QEV101BDDFREQ [TEMEX]
暂无描述;FREQUENCY
QEV101
SMD 7x5 VCXO – Communications Equipment Application
Specification (Rev-F)
Electrical Characteristics ......................................................P01
Mechanical Characteristics...................................................P02
Ordering Information.............................................................P03
Suggested Reflow Soldering profile......................................P03
Tape Drawing........................................................................P04
Reel Drawing ........................................................................P04
F r e q u e n c y
QEV101
SMD 7x5 VCXO – Communications Equipment Application
Specification (rev-F)
April 05th, 2006
Electrical Characteristics
Electrical Parameters
Frequency range
Unit
Minimum
Typical
Maximum
Test conditions
MHz
1.544
65.536
HCMOS / TTL Output
0 to +70
Output logic
Operating temperature
Refer to Ordering
Information
°C
°C
-40 to +85
+125
range (see table 1)
-55
Storage temperature range
Power supply voltage (VCC)
Refer to Ordering
Information
VDC
3.135
4.750
3.3
5.0
3.465
5.250
3.3V version
5.0V version
Refer to Ordering
Information
Frequency Stability
± ppm
± ppm
±25 or ±50
(see note 1)
Aging (First Year)
3
Ref at 25°C
Input current
3.3V version
mA
pF
40mA
55mA
5.0V version
HCMOS Output load
15
30
Output Logic Levels
Output Logic High (VOH)
Output Logic Low (VOL)
With 30pF HCMOS
Load
VDC
90%VCC
10%VCC
Pullability
Refer to Ordering
Information
± ppm
±50, ±100 or ±150
3.3V ⇒ VC=1.65 ±1.50V
5.0V ⇒ VC=2.50 ±2.00V
Positive slope
%
%
20
55
Linearity
Duty cycle
45
50
Rise & Fall time
Start-up time
ns
10
10
20% VCC ~ 80% VCC
ms
KΩ
100
Input Impedance
Note 1: Include 25°C tolerance, operating temperature range, input voltage change (VCC±5%), load change
(15pF±10%), first year aging, shock and vibration.
Table 1 : Stability Codes
Table 2 : Phase Noise
± 25ppm
± 50ppm
Maximum values for 20MHz VCXO
0 to +70°C
C
D
A
B
Unit
10Hz
dBc/Hz
- 60
- 40 to +85°C
100Hz
1KHz
10KHz
Floor
- 90
-120
-135
-145
1
TEMEX reserves the right to modify herein specifications and informations at any time when necessary to provide optimum performance and cost.
F r e q u e n c y
QEV101
SMD 7x5 VCXO – Communications Equipment Application
Specification (rev-F)
April 05th, 2006
Mechanical Characteristics
BOTTOM VIEW
SUGGESTED PAD
Hmax = 2.0mm max
Pin connections
#1
#2
#3
#4
#5
#6
VCONTROL
Tri state
Ground
Output
N.C.
+VCC
Tristate Function
Marking
Line 1 Manufacturing code + V1 + stability/supply voltage/pulling code
Line 2 Frequency in MHz (6 digits)
Pin ≠1
Open
“1”
Output (Pin ≠4)
Active
Line 3 Date code (YYWW)
Active
“0”
High Z
Example for QEV101BAB / 10MHz
ꢀ Line 1 : NV1BAB
ꢀ Line 2 : 10.000
ꢀ Line 3 : 0614
2
TEMEX reserves the right to modify herein specifications and informations at any time when necessary to provide optimum performance and cost.
F r e q u e n c y
QEV101
SMD 7x5 VCXO – Communications Equipment Application
Specification (rev-F)
April 05th, 2006
Ordering Information
Part numbering system
QEV101
B
A
B
10.000MHZ
Package type
Temperature Stability
Supply
Voltage
Pulling Range
Nominal
Frequency (MHz)
SMD Package
A : + 5.0V
D : +3.3V
Please enter the
A : ± 100ppm min
B : ± 150ppm min
A : ± 50ppm vs 0 to +70°C
B :± 50ppm vs -40 to +85°C
C : ± 25ppm vs 0 to +70°C
D :± 50ppm vs -40 to +85°C
QEV101 : SMD 7x5
nominal frequency
D :
± 50ppm min
Suggested Reflow Soldering Profile
3
TEMEX reserves the right to modify herein specifications and informations at any time when necessary to provide optimum performance and cost.
F r e q u e n c y
QEV101
SMD 7x5 VCXO – Communications Equipment Application
Specification (rev-F)
April 05th, 2006
Tape Drawing
Item
Code
Dimension
Tolerance
Pitch of components
P
Po
P1
W
8.0
4.0
± 0.1
± 0.1
Pitch of sprocket hole
Length from hole center to component center
Width of carrier tape
2.0
± 0.1
16.0
7.5
+0.3/-0.1
± 0.1
Width of adhesive tape
W0
A
Height of component hole
Width of component hole
Gap of hold down tape and carrier tape
Diameter of sprocket hole
Diameter of feed hole
8.18
5.56
1.75
∅ 1.5
∅ 1.5
2.16
± 0.1
B
± 0.1
W2
Do
D1
K
± 0.1
± 0.05
± 0.25
± 0.1
Total of tape thickness
Reel Drawing
Multiple : 1Kpcs per Reel
Unit : mm
4
TEMEX reserves the right to modify herein specifications and informations at any time when necessary to provide optimum performance and cost.
相关型号:
©2020 ICPDF网 联系我们和版权申明