1055525-1 [TE]
The production cable pointers are hand-fed pointers that use a small diameter cutter to allow âpointing" of pre-bent cable assemblies.;型号: | 1055525-1 |
厂家: | TE CONNECTIVITY |
描述: | The production cable pointers are hand-fed pointers that use a small diameter cutter to allow âpointing" of pre-bent cable assemblies. |
文件: | 总2页 (文件大小:55K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Instruction Sheet
Production Coaxial Cable Pointers
1080269-1 and 1055525-1
408-8821
12 JAN 12 Rev B
Cover
CenterConductor
Holder
Foot
Pedal
SEMI-RIGID COAXIAL CABLE
SIZE (mm [in.])
PRODUCTION COAXIAL CABLE POINTER
TYPE
1080269-1 ‡
1055525-1 ‡
RG-405/U
RG-402/U
2.197 [.086]
3.581 [.141]
‡ Replacement Cutter Blade 1055529-1 is Available for This Cable Pointer
Figure 1
3. Slowly insert the cable center conductor into the
center conductor holder.
1. INTRODUCTION
These production cable pointers are used to point the
cable type and size listed in Figure 1.
4. With no pressure on the cable, press the foot
pedal to begin pointer assembly operation.
Dimensions in this instruction sheet are in metric
NOTE
5. Slowly feed the cable (with light pressure) in until
the cable face stops against the center conductor
holder.
units [with U.S. customary units in brackets].
Figures are not drawn to scale.
i
6. Remove the cable. The proper center conductor
length and point should now be achieved. If
necessary, refer to Section 4 and Section 5.
Reasons for reissue of this instruction sheet are
provided in Section 7, REVISION SUMMARY.
2. DESCRIPTION
4. CENTER CONDUCTOR LENGTH ADJUSTMENT
The production cable pointers are hand-fed pointers
that use a small diameter cutter to allow “pointing" of
pre-bent cable assemblies. Various standard center
conductor lengths may be obtained by means of a
simple adjustment.
To change the length of the center conductor, proceed
as follows:
1. Loosen the center conductor holder set screw.
2. Using appropriate gripping material (such as a
pencil eraser), turn the center conductor holder set
screw clockwise to shorten the center conductor
length; turn the center conductor holder set screw
counterclockwise to lengthen the center conductor.
3. POINTING PROCEDURE
1. Cut the coaxial cable to the length required.
2. Trim the cable jacket to expose the center
conductor. The following production cable trimmers
are available.
One complete turn equals approximately 0.15 mm
[.006 in.].
NOTE
i
Production Cable Trimmer
1055530-1
Cable Size (mm [in.])
2.197 [.086]
3. Tighten the set screw lightly so that no damage is
done to the threads on the center conductor holder.
1055526-1
3.581 [.141]
©2012 Tyco Electronics Corporation, a TE Connectivity Ltd. Company TOOLING ASSISTANCE CENTER 1-800-722-1111
All Rights Reserved
*Trademark
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.te.com
1 of 2
PRODUCT INFORMATION 1-800-522-6752
LOC B
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.
408-8821
There is a small piece of fluoropolymer in the
threaded hole which prevents the set screw from
touching the threads on the center conductor
holder. DO NOT lose the piece of fluoropolymer.
8. Clean with pressurized air.
CAUTION
Make sure to follow all local practices, particularly
wearing safety glasses, when using pressurized air.
DANGER
!
STOP
5. CUTTER REPLACEMENT (See Figure 2)
9. Replace the cutter blade. Reverse these steps to
re-assemble.
Replacement Cutter Blade 1055529-1 is available
for Cable Pointer 1055525-1.
NOTE
6. MAINTENANCE
i
Occasionally remove the cover and the cable holder
and clean these areas with pressurized air. If
necessary, clean the shavings with a razor knife or
tweezers.
1. Turn “off" the power.
2. Remove the cover.
3. While holding the cutter holder with a pair of
pliers, loosen the 5/16-24 UNF nut at rear of the
spindle.
Make sure to follow all local practices, particularly
wearing safety glasses, when using pressurized air.
DANGER
STOP
4. Remove the draw bar (5/16-24 UNF threaded
rod).
7. REVISION SUMMARY
5. Unlock the two 7/8-in. diameter collars from the
spindle using a hex wrench.
Revisions to this instruction sheet include:
6. Slide the spindle back through the bearings to
separate it from the cutter holder.
• Changed company name and logo
• Replaced trademark with fluoropolymer in
7. Remove the cutter holder and front bearing. Hold
the cutter holder and front bearing, and with a slight
rocking motion, pull them away from the plate.
CAUTION of Step 3 of Section 4
Cutter Replacement
Spindle
Cutter
Cover Holder
Nut
Draw
Bar
Collars
Figure 2
2 of 2
Rev B
相关型号:
1055526-1
The production cable pointers are hand-fed pointers that use a small diameter cutter to allow âpointing" of pre-bent cable assemblies.
TE
1055530-1
The production cable pointers are hand-fed pointers that use a small diameter cutter to allow âpointing" of pre-bent cable assemblies.
TE
©2020 ICPDF网 联系我们和版权申明