1059773-1 [TE]
Installation Tool 1059773-1ï;型号: | 1059773-1 |
厂家: | TE CONNECTIVITY |
描述: | Installation Tool 1059773-1ï |
文件: | 总2页 (文件大小:72K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Instruction Sheet
Installation Tool 1059773-1
for OSP* Hermetic Plug Connectors
408-8778
10 AUG 11 Rev A
PROPER USE GUIDELINES
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use
and low volume applications. A wide selection of powered application equipment for extended-use, production operations is available.
Locking Handle
in Open Position
Handle
(Torque Driver)
Locking Handle
in Closed Position
Collet
Collet Adjustment Nut
TOOL
CONNECTOR TYPE
PRESET TORQUE
TE PART
NUMBER
REVIOUS PART
NUMBER
DESCRIPTION
1059773-1
1059765-1
4598-5014-54
4598-3200-54
Installation Tool
OSP Hermetic
Plug Connector
18 In.-Lbs.
Replacement Head Assembly
Figure 1
1. INTRODUCTION
3. INSTALLATION AND REMOVAL
3.1. Installation
Installation Tool 1059773-1 (Figure 1) is used to install
and remove OSP Hermetic Plug Connectors. Figure 1
also lists the available replacement head that may be
purchased from Tyco Electronics separately.
1. Place the hermetic plug connector in the collet.
The connector should bottom on a stop within the
collet.
NOTE
Dimensions in this document are in metric units
[with U.S. customary units in brackets], unless
NOTE
i
otherwise indicated.
i
2. Once the connector is in place in the collet, move
the locking handle to the closed position. This
secures the connector in the tool.
2. DESCRIPTION
Do not force the locking handle closed. If the
handle does not easily close the collet tension may
CAUTION
Installation Tool 1059773-1 contains an adjustablE
handle that allows for torque settings between 6 in.-
lbs. and 30 in.-lbs. This tool also contains a connector-
specific head assembly.
have to be adjusted.
!
3. If necessary, turn the adjustment nut until the
connector is held snuggly in place.
Once the tool head is adjusted for the specific
connector, the installation of multiple connectors is
made easy with a quick-release locking handle.
The collet adjusting nut is covered with a heat
shrink tubing to help maintain adjustment.
NOTE
A collet at the end of the assembly, holds the
connector. A collet adjustment nut tightens the
connector in the collet.
i
The locking handle is used to secure the hermetic
style plug in place during installation, and release the
hermetic style plug assembly after installation.
CAUTION
Damage to the connector may result if the collet is
not properly adjusted.
!
©2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company TOOLING ASSISTANCE CENTER 1-800-722-1111
All Rights Reserved
*Trademark
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.te.com
1 of 2
PRODUCT INFORMATION 1-800-522-6752
LOC B
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.
408-8778
4. Holding the handle, turn the tool clockwise to
thread the plug connector together.
4. Holding the handle, turn the tool
counterclockwise to unthread the plug connector.
5. Continue turning the handle (and connector) until
the drive handle makes a "clicking" sound. This
clicking sound is an indication that the proper torque
has been reached.
5. Move the locking handle to the open position to
release the connector.
4. REPLACEMENT
6. Move the locking handle to the open position to
release the connector.
The torque driver contains a 6.35 [.250] square drive
which accepts the replacement head (shown in
Figure 1).
3.2. Removal
1. Pull the head off the standard 6.35 [.250] square
drive.
1. Place the hermetic plug connector into the collet.
The connector should bottom on a stop within the
collet.
2. Snap the replacement head (Figure 1) onto the
square drive.
NOTE
i
3. Order replacements from your TE representative,
or call 1-800-526-5142, or send a facsimile of your
purchase order to 1-717-986-7605, or write to:
2. Once the connector is in place in the collet, move
the locking handle to the closed position. This
secures the connector in the tool.
CUSTOMER SERVICE (038-035)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
Do not force the locking handle closed. If the
CAUTION
HARRISBURG PA 17105-3608
handle does not easily close the collet tension may
For tool repair service, please contact a representative
at 1-800-526-5136.
have to be adjusted.
!
5. REVISION SUMMARY
3. If necessary, turn the adjustment nut until the
connector is held snuggly in place.
Since the previous release, the new company logo
was applied.
The collet adjusting nut is covered with a heat
NOTE
shrink tubing to help maintain adjustment.
i
Damage to the connector may result if the collet is
not properly adjusted.
CAUTION
!
2 of 2
Rev A
相关型号:
©2020 ICPDF网 联系我们和版权申明