1214044-1 [TE]
Reasons for reissue are provided in Section 7, REVISION SUMMARY.;
| 型号： | 1214044-1 |
| 厂家： | 
TE CONNECTIVITY |
| 描述： | Reasons for reissue are provided in Section 7, REVISION SUMMARY. |
| 文件： | 总4页 (文件大小：106K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Instruction Sheet
Seating Tool Assemblies 1320142-[ ] and 356198-[ ]
For CHAMP* .050 Series I Blindmate Press-Fit
Connectors with Compliant Pin Contacts
408-4328
28 APR 11 Rev C
Seating Tool
Assembly
356198-1 (Ref)
CHAMP .050 Series I
Blindmate Press-Fit
Vertical Receptacle
Connector (Ref)
Compliant Pin Contact
(Board Retention Feature)
PC (Printed
Circuit) Board
(Ref)
NO. OF
CONNECTOR
ROWS
SEATING
TOOL
CONNECTOR
TYPE
Extended
Height
1320142--1
40
PC Board Support
Fixture (Ref)
1320142--2
356198--1
356198--2
356198--3
80
80
40
20
Press--Fit
Press--Fit
Figure 1
1. INTRODUCTION
2. DESCRIPTION
During seating, the seating tool covers the connector
and presses on the top surface of the connector when
the applicator ram applies force to the seating tool.
The pc board is positioned onto a pc board support
fixture for support.
Seating Tool Assemblies 1320142--[ ] and 356198--[ ]
are designed to seat CHAMP .050 Series I Blindmate
press--fit and extended height press--fit vertical
receptacle connectors. The connectors contain
compliant pin contacts to allow solderless pc board
installation. Each seating tool is specifically designed
for the number of rows in a connector. See Figure 1.
Read these instructions and understand them before
using the seating tool.
3. REQUIREMENTS
3.1. PC Board Support Fixture (Customer Supplied)
Dimensions on this sheet are in metric units [with
U.S. customary units in brackets]. Figures are not
drawn to scale.
NOTE
A pc board support must be used to provide proper
support for the pc board and alignment of the seating
tool to the contacts, and to protect the pc board and
and connector from damage. The board support
fixture must be designed for specific needs using the
recommendations in Instruction Sheet 408--6927.
i
Reasons for reissue are provided in Section 7,
REVISION SUMMARY.
E2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company
All Rights Reserved
*Trademark
TOOLING ASSISTANCE CENTER 1--800--722--1111 This controlled document is subject to change.
1 of 4
PRODUCT INFORMATION 1--800--522--6752
For latest revision and Regional Customer Service,
visit our website at www.te.com
LOC B
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.
408-4328
2. Position connector onto pc board so that the
connector contacts are properly aligned to the pc
board and pc board support fixture.
3.2. Application Tooling
Power for seating tools must be provided by a
machine capable of supplying a downward force of
20 Newtons (N) [5 lb] per contact. 10/20--Ton “H”
Frame Assembly 803880--6 (Customer Manual
409--5567 provides instructions), SM--3 Frame
Assembly 814700--2 (409--5626), or GreenerdG
Frame Assemblies 3A and 3B equipped with Adapter
Kit (408--9027) can be used.
3. Insert connector into pc board until the contacts
are resting securely on, but have not fully entered,
the board.
4. Position the seating tool on the connector,
making sure that the tool is bottomed on the
housing floor.
5. Center the seating tool and connector under the
applicator ram of the tool. Lower the ram slowly
until it just meets the seating tool. Verify alignment
of pc board support, pc board, connector, and
seating tool.
4. SEATING
When setting up equipment to seat connectors, pay
particular attention to the following:
S The seating tool must be matched to the
connector
Damage to the pc board, seating tool, or
connector may occur if seating height is
improperly set or if tool is not properly seated in
the connector before cycling the tool.
CAUTION
S The seating tool, connector, and applicator ram
must be properly aligned before cycling the tool
!
If the tool and connector are mismatched or are
improperly aligned, damage could occur to the
tooling, connector, or both.
CAUTION
6. Cycle the tool to seat the connector in the pc
board. Then retract the ram and carefully remove
the seating tool. Check assembly for proper
seating according to Application Specification
114--6061.
!
1. Set seating height to the dimension shown in
Figure 2 (applicator shut height will equal the
seating height PLUS the combined thicknesses of
the pc board and pc board support).
7. Repeat Steps 2 through 6 until all the
connectors are seated.
View After Seating
Applicator Ram
(Fully Down)
Seating Tool Centered
Under Applicator Ram and
Bottomed on Connector
Seating Height
(Connector Seated)
38.1+0.25/ -0.00 mm
Applicator
Shut Height
[1.50+.010/ -.000 in.]
(Ram Fully Down)
(See Section 4, Step 1)
Connector Contacts Inserted
into Holes in PC Board and
PC Board Support Fixture
PC Board
PC Board Support
Fixture (Ref)
Note: Not to Scale
Figure 2
GTrademark of Greenerd Press & Machine Co., Inc.
2 of 4
Rev C
408-4328
should remain with the tooling or be supplied to
supervisory personnel responsible for the tool.
Inspection frequency should be based on amount of
use, working conditions, operator training and skill,
and established standards.
5. MAINTENANCE AND INSPECTION
The seating tool is assembled and inspected before
shipment. TE Connectivity recommends that the tool
be inspected immediately upon arrival at your facility
to ensure that the tool has not been damaged during
shipment, and that the tool conforms to the
dimensions provided in Figure 3.
6. REPLACEMENT AND REPAIR
5.1. Daily Maintenance
Refer to Figure 3 for customer--replaceable parts. A
complete inventory should be stocked to prevent
production downtime when replacement of parts is
necessary. Order replacement parts through your TE
representative, or call 1--800--526--5142, or send a
facsimile of your purchase order to 717--986--7605, or
write to:
TE recommends that each operator be made aware
of, and responsible for, the following steps of daily
maintenance:
1. Remove dust, moisture, and contaminants with
a clean, soft brush or a lint--free cloth. Do NOT use
objects that could damage the tool components.
CUSTOMER SERVICE (038--035)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
2. When the tool is not in use, store it in a clean,
dry area.
HARRISBURG PA 17105--3608
5.2. Periodic Inspection
Regular inspections should be performed by quality
control personnel. A record of scheduled inspections
For customer repair service, please contact a TE
representative at 1--800--526--5136.
38.1 mm
[1.50 in.]
Dim. A
4
1
3
38.02 mm
[1.497 in.]
2
DIMENSION A (Length mm [in.]) FOR SEATING TOOL
1320142-1
1320142-2
95.3 [3.75]
50.8 [2.00]
REPLACEMENT PARTS
PART NUMBER FOR ASSEMBLY
1320142-1 1320142-2
QTY PER
DESCRIPTION
ITEM
ASSEMBLY
1--21002--3
—
—
SCREW, Button Head Cap 4--40
SCREW, Button Head Cap 4--40
BLADE, Insertion
2
4
1
2
3
4
1--21002--3
1320143--2
—
1320143--1
2--21012--8
—
2
SCREW, Socket Set 6--32
SCREW, Socket Set 6--32
ADAPTER
5
2--21012--8
354699--1
10
1
354698--2
Figure 3 (cont’d)
Rev C
3 of 4
408-4328
9
5
3
38.1 mm
[1.50 in.]
4
2
1
38.02 mm
[1.497 in.]
7
8
Dim. A
DIMENSION A (Length mm [in.]) FOR SEATING TOOL
356198-1
74.7 [2.94]
356198-2
356198-3
35.6 [1.40]
49.3 [1.94]
REPLACEMENT PARTS
PART NUMBER FOR ASSEMBLY
QTY PER
ITEM
DESCRIPTION
ASSEMBLY
356198-1
356195--1
356198-2
356195--2
1214044--1
1--21002--7
1214041--2
2--21002--1
—
356198-3
1
2
3
4
356195--3
1214044--1
1--21002--7
1214041--2
—
BAR, Push
1
2
4
1
2
1
2
2
1
1
2
1214044--1
1--21002--7
1214041--1
2--21002--1
—
PLATE, End
SCREW, Button Head Cap 6--32
PLATE, Stabilizer
SCREW, Button Head Cap 8--32
SCREW, Button Head Cap 8--32
PLATE, Side
5
6
7
2--21002--1
356194--3
—
356194--1
2--21000--9
—
356194--2
2--21000--9
—
SCREW, Socket Head Cap 8--32
SCREW, Socket Head Cap 8--32
NUT, Hex 8--32
2--21000--9
—
21018--6
—
21018--6
—
8
21018--6
NUT, Hex 8--32
Figure 3 (end)
7. REVISION SUMMARY
Since the previous version of this document, the
following changes were made:
S Updated document to corporate requirements.
4 of 4
Rev C
相关型号：
©2020 ICPDF网 联系我们和版权申明