1424587-3 [TE]
Read these instructions and understand them before using the seating tool.;
| 型号： | 1424587-3 |
| 厂家： | 
TE CONNECTIVITY |
| 描述： | Read these instructions and understand them before using the seating tool. |
| 文件： | 总3页 (文件大小：147K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Instruction Sheet
Seating Tools 91346-[ ]
for Z-PACK* 2mm HM (Hard Metric),
Type A/B Pin Headers
408-8465
04 OCT 11 Rev A
Seating Tools
91346-[ ]
Adapter
Blade
Typical Z-PACK 2mm
HM Pin Header
Printed Circuit
Board (Ref)
ACTION PIN* Contact
Board Retention Feature
Printed Circuit Board
Support Fixture
(Customer Supplied)
Figure 1
1. INTRODUCTION
2. DESCRIPTION
This instruction sheet covers the use and maintenance
of Seating Tools 91346-[ ].
Each seating tool is an assembly of a blade and an
adapter. Figure 2 matches tool part number to the size
(positions) of the pin header to be seated. The adapter
straightens the header, during the cycle of the
applicator ram, to provide proper insertion into the pc
board. Each tool is designed for a specific combination
of contacts in a row and number of rows in a header.
During seating, the tool sits inside the header housing
with the blades engaging the housing floor and contact
shoulders, preventing contacts from pushing out of
the housing.
These tools are used to seat Z-PACK 2mm HM (hard
metric) 5-row and 5-row +2 Type A/B pin headers
onto a printed circuit (pc) board. These headers
contain ACTION PIN contacts to allow solderless pc
board installation. See Figure 1.
Read these instructions and understand them before
using the seating tool.
Dimensions in this instruction sheet are in metric
units [with U.S. customary units in brackets].
NOTE
Figures are not drawn to scale.
i
©2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company TOOLING ASSISTANCE CENTER 1-800-722-1111
All Rights Reserved
*Trademark
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.te.com
1 of 3
PRODUCT INFORMATION 1-800-522-6752
LOC B
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.
408-8465
Adapter Length
2
3
Blade Length
(Ref)
13.34 mm [.525 in.]
Blade Width
1
DESCRIPTION
(Length in mm [in.]
QUANTITY FOR SEATING TOOL
PART
NUMBER
ITEM
1
91346-1
91346-2
91346-3
+0.00/-0.10 [+.000/-.004]
BLADE, 25 Column, 49.9 [1.95]
BLADE, 22 Column, 43.9 [1.73]
BLADE, 19 Column, 37.9 [1.49]
ADAPTER, 50.80 [2.000]
1424587-1
1424587-2
1424587-3
354698-1
2-21012-8
1
- -
- -
1
- -
1
- -
- -
1
- -
1
2
3
1
SOCKET SETSCREW, 6-32 X .19 In.
5
3
3
Figure 2
2. Position header into pc board so that header
contacts are properly aligned to the board and
board support.
3. REQUIREMENTS
3.1. PC Board Support Fixture (Customer Supplied)
A pc board support must be used to provide proper
support for the pc board and alignment of the tool to
the header pins, and to protect the pc board and
header posts from damage. Design a pc board
support fixture for your specific needs using the
recommendations in Instruction Sheet 408-6927.
3. Insert header into pc board until the ACTION PIN
post section of the contacts are resting securely on,
but have not fully entered, the pc board.
4. Position appropriate seating tool into header,
making sure tool is bottomed on housing floor.
5. Center seating tool and header under the
applicator ram of the power source; slowly lower
ram until it just meets the seating tool. Verify the
alignment of the board support, pc board, header,
and seating tool.
3.2. Application Tooling
Power for the seating tool must be provided by an
application tool (with a ram) capable of supplying a
downward force of 133 N [30 lb] per contact.
Damage to the pc board, tool, or header may occur
if seating height is improperly set, or if tool is not
properly seated in the header before cycling the
applicator ram.
Manual Electric Servo Presses (CMP 6T) 1585699-8
and (CMP 12T) 1585698-8, and Bench Top Electric
Servo Press (CBP 5T) 1585696-9 are available for this
seating tool.
CAUTION
!
6. Cycle applicator ram according to instructions for
the power source. Check assembly for proper
seating using the requirements in Figure 3.
For information on the presses, visit the press-fit
assembly equipment website at
http://tooling.te.com/pressfit.asp.
7. Remove pc board and seated header, or
reposition board and board support for seating
additional headers.
4. SEATING
1. Set seating height to the dimension shown in
Figure 3 (applicator shut height will equal the
seating height PLUS the combined thicknesses of
the pc board and pc board support).
2 of 3
Rev A
408-8465
View After Seating
Applicator Ram
(Fully Down)
Seating Tool Bottomed
on Housing Floor
Seating Height
(Header Seated)
38.10 +0.25/-0.00mm
[1.50 +.010/-.000 In.]
Contact Posts in Holes in
PC Board and Aligned with
Holes in Board Support
Applicator Shut Height
(Ram Fully Down)
(See Section 4, Step 1)
PC Board
PC Board Support
Fixture (Ref)
Figure 3
5. TOOL INSPECTION
7. REPLACEMENT AND REPAIR
Each seating tool is assembled and inspected before
shipment. We recommend that the tool be inspected
immediately upon arrival at your plant to ensure that it
has not been damaged during shipment.
The parts listed in Figure 2 are customer-replaceable.
A complete inventory can be stocked and controlled to
prevent lost time when replacement of parts is
necessary. Order replacement parts through your Tyco
representative, or call 1-800-526-5142, or send a
facsimile of your purchase order to 717-986-7605, or
write to:
Regular inspections should be performed by quality
control personnel. A record of scheduled inspections
should remain with the tool or be supplied to
supervisory personnel responsible for the tool. The
inspection frequency should be based on the amount
of use, working conditions, operator training and skill,
and established company standards.
CUSTOMER SERVICE (038-035)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
HARRISBURG PA 17105-3608
6. MAINTENANCE
For customer repair service, call 1-800-526-5136.
It is recommended that each operator be made aware
of, and responsible for, the following steps of daily
maintenance:
8. REVISION SUMMARY
Since the previous version of this document, the
following changes were made:
1. Remove dust, moisture, and other contaminants
with a clean, soft brush, or lint-free cloth. Do NOT
use objects that could damage the tool.
• Changed Paragraph 3.2.
• Updated document to corporate requirements.
2. Ensure that the screws are in place and secured.
3. When the tool is not in use, store it in a clean,
dry area.
3 of 3
Rev A
相关型号：
©2020 ICPDF网 联系我们和版权申明