1725731-1 [TE]
626 Pneumatic Crimping Head 1490191-1 (Used with 626 Pneumatic Tooling Assemblies);型号: | 1725731-1 |
厂家: | TE CONNECTIVITY |
描述: | 626 Pneumatic Crimping Head 1490191-1 (Used with 626 Pneumatic Tooling Assemblies) |
文件: | 总4页 (文件大小:217K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Instruction Sheet
626 Pneumatic Crimping Head
1490191-1 (Used with 626 Pneumatic
Tooling Assemblies)
408-8878
07 MAR 12 Rev A
Quick Pin(s)
(Ref)
354425-1
Assembly Pins
Rollers
Anvil Crimping Jaws
Tool Holder
Assembly 189767-1
CRIMPING HEAD POWER UNITS
Crimping Head
1490191-1
189721-1
Guard
1490191-1
189722-1
Indenter Crimping Jaw
Figure 1
1. INTRODUCTION
3. HEAD INSTALLATION AND REMOVAL
3.1. Installation
The 626 Pneumatic Crimping Head, 1490191-1, is
designed to crimp wire ferrules on solid or stranded
copper wire. The crimping head is used with 626
Pneumatic Tooling Assemblies. Figure 1 shows the
tool holder assembly, and lists the power units for the
crimping head.
Crimping heads are coated with a preservative to
NOTE
prevent rust and corrosion. Wipe any excess
preservative from the head, particularly from the
crimping surfaces.
i
To avoid personal injury, ALWAYS disconnect tool
from air supply before installing crimping head.
DANGER
This instruction sheet provides recommended
procedures for crimp head installation, crimping, and
maintenance and inspection. For information
concerning tool setup and operation, refer to the
customer manual packaged with the appropriate tool.
STOP
Do NOT operate pneumatic tool without proper
crimping head installed; make sure that the quick
pins are FULLY tightened to avoid personal injury
and damage to the tool.
DANGER
Read these instructions thoroughly before proceeding
STOP
Measurements are in metric units [followed by U.S.
Customary units in brackets]. Figures are for
NOTE
1. Remove quick pins from tool holder.
reference only, and are not drawn to scale.
i
2. Insert crimping head into tool holder as shown in
Figure 1.
2. DESCRIPTION
3. After crimping head is properly aligned, insert and
tighten the quick pins provided with the tool holder
assembly.
The pneumatic crimping head consists of integral jaws
which close in an arc-like motion. After an operator
locates the ferrule between the crimping jaws and
inserts the stripped wire, the tool is activated to crimp
the ferrule to the wire.
©2012 Tyco Electronics Corporation, a TE Connectivity Ltd. company TOOLING ASSISTANCE CENTER 1-800-722-1111
All Rights Reserved
*Trademark
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.te.com
1 of 4
PRODUCT INFORMATION 1-800-522-6752
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.
408-8878
TE Connectivity recommends using Loctite No.
242, removable threadlock or equivalent, to prevent
the quick pins from loosening.
4. Insert stripped wire into ferrule as shown in
Figure 3.
NOTE
i
4. Connect tool to an adequate air supply between
620-690 kPa [90-100 psi]. For specific information
on air line requirements and air hose installation,
refer to the customer manual packaged with the
pneumatic power unit.
3.2. Removal
ALWAYS disconnect tool from air supply before
removing crimping head.
DANGER
STOP
Remove quick pins from the crimping head; then
remove crimping head from the tool holder.
4. CRIMPING PROCEDURES
Figure 3
To avoid personal injury, always keep fingers clear
of crimping jaws when operating the tool. Never
place anything within the crimping jaws except
DANGER
5. Activate the tool to complete the crimp. Open the
crimping jaws by squeezing the rollers together
simultaneously; then remove the crimped ferrule.
STOP
terminals or splices.
Crimping head shown without guard for clarity.
Damaged ferrules should not be used. If a
damaged ferrule is evident, it should be cut from
the wire and replaced.
NOTE
NOTE
i
i
1. Strip wire to required length. DO NOT nick the
wire strand or use wires with nicked or missing
conductor strands.
5. MAINTENANCE AND INSPECTION
To avoid personal injury, disconnect tool from air
supply before performing any maintenance,
inspection, or repairs.
DANGER
2. Open crimping jaws by squeezing the rollers
together simultaneously; then place the ferrule into
the center of the appropriate chamber, as shown in
Figure 2. Use the correct crimp chamber for the
specific wire size.
STOP
It is recommended that a maintenance and inspection
program be performed periodically to ensure
dependable and uniform terminations. Heads should
be inspected once a month. Frequency of inspection
should be adjusted to suit your requirements through
experience and depends on:
Center Ferrule
In Dies
1. The care, amount of use, and handling of
the head.
2. The type and size of the products crimped.
3. The degree of operator skill.
4. The presence of abnormal amounts of dust
and dirt.
5. Your own established standards.
Each crimping head is thoroughly inspected before
packaging. Since there is the possibility of crimping
head damage in shipment, new crimping heads should
be inspected immediately upon arrival at your facility.
Figure 2
3. After ferrule is properly positioned, release the
rollers to allow the jaws to spring shut, holding the
ferrule in place.
5.1. Daily Maintenance
It is recommended that each operator be responsible
for the following steps of daily maintenance:
2 of 4
Rev A
408-8878
1. Remove dust, moisture, and other contaminants
with a clean, soft brush, or a lint-free cloth. Do NOT
use objects that could damage the heads.
die closure area onto certain terminations may affect
the electrical characteristics of a termination.
5.5. Gaging the Crimping Chamber
2. Make sure pins, rings, and other components are
in place and secure.
This inspection requires the use of plug gages
conforming to the dimensions shown in Figure 4. TE
does not manufacture or market these gages.
Make sure quick pins, are in place and FULLY
tightened to avoid personal injury and damage to
the tool.
DANGER
STOP
GO Diameter
NO-GO Diameter
3. Make certain all surfaces are protected with a thin
coat of any good SAE 20 motor oil. Do NOT oil
excessively.
4. When the head assembly is not in use, store it in
a clean, dry area.
50.8 [2.0] Min Typ
5.2. Periodic Inspection
Jaw Closure
Configuration
Regular inspections should be performed by quality
control personnel. A record of scheduled inspections
should remain with the crimping heads or be supplied
to supervisory personnel responsible for the crimping
heads. Though recommendations call for at least one
inspection a month, the frequency should be based on
amount of use, working conditions, operator training
and skill, and your established company policies.
These inspections should include a visual inspection
(Paragraph 5.3 and a crimping chamber inspection
(Paragraph 5.5).
WIRE
GAGE ELEMENT DIMENSIONS
CRIMPING
HEAD
RANGE,
mm²
GO
NO-GO
1.371 - 1.379
[.0540 - .0543]
1.496 - 1.498
[.0589 - .0590]
2.4
4.0
6.0
1.955 - 1.963
[.0770 - .0773]
2.080 - 2.082
[.0819 - .0820]
1490191-1
2.362 - 2.369
[.0930 - .0933]
2.486 - 2.489
[.0979 - .0980]
5.3. Visual Inspection
Figure 4
1. Remove all lubrication and accumulated film by
immersing the crimping head in a suitable
commercial degreaser that will not affect paint
or plastic.
To avoid personal injury, disconnect air supply and
remove crimping head from tool before inspection
the crimping chambers.
DANGER
STOP
2. Make certain all components are in place. If
replacements are necessary, refer to Figure 6.
1. Remove oil and dirt from the bottom of the jaw
surfaces, and plug gage element surfaces.
3. Check all bearing surfaces for wear. Make sure
the rollers turn freely with minimal resistance.
Replace any worn parts.
2. Close the crimping jaws until they are bottomed,
but not under pressure.
3. Align the GO element with the crimping chamber.
Push the GO element straight into the crimping
chamber without using force. The GO element must
pass completely through the crimping chamber. See
Figure 5.
4. Inspect the crimp area for flattened, chipped, or
broken areas. Although the crimping chambers may
gage within permissible limits, worn or damaged die
closure surfaces are objectionable and will affect
the quality of the crimp.
4. Align the NO-GO element with the crimping
chamber, and try to insert it straight into the
crimping chamber. The NO-GO element may start
entry but must not pass completely through the
chamber.
5.4. Lubrication
Lubricate all pins, pivot points, and bearing surfaces
with a high quality grease. TE recommends the use of
Molykote paste, which is a commercially available
lubricant. Lubricate according to the following
schedule:
— Head used in daily production - lubricate daily
— Head used daily (occasional) - lubricate weekly
— Head used weekly - lubricate monthly
Wipe excess grease from crimping head, particularly
from die closure areas. Grease transferred from the
3 of 4
Rev A
408-8878
GO Element Must Pass
Completely Through
the Crimping Jaws
NO-GO Element May
Enter Partially, But
Must Not Pass Through
the Crimping Jaws
Jaws Bottomed But
Not Under Pressure
Figure 5
If the jaw closure meets the plug gage conditions, the
crimping head is considered dimensionally correct and
should be lubricated with a THIN coat of any good
SAE 20 motor oil. If the crimping chambers do not
conform to the plug gage conditions, contact your local
TE Field Service Engineer, or refer to Section 6,
REPLACEMENT AND REPAIR.
Order replacement parts through your TE
Representative, or call 1-800-526-5142, or send a
facsimile of your purchase order to 1-717-986-7605, or
write to:
CUSTOMER SERVICE (038-035)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
For additional information about the use of a plug
gage, refer to Instruction Sheet 408-7424.
HARRISBURG PA 17105-3608
For customer repair service, call 1-800-526-5136.
6. REPLACEMENT AND REPAIR
7. REVISION SUMMARY
Replacement parts and recommended spares are
listed in Figure 6. The recommended spares should
be stocked for immediate replacement. Parts should
be replaced by TE to ensure quality and reliability of
the tool.
Since the previous version of this document, the
following changes were made:
• Updated document to corporate requirements.
2
3
9
8
7
4
5
10
1
11
6
QTY
PER
HEAD
QTY
PER
HEAD
ITEM
NO.
ITEM
NO.
PART NO.
DESCRIPTION
PART NO.
DESCRIPTION
1
2
3
4
5
1725731-1 ANVIL, Wire Ferrule
23241-2 BALL, Steel
1725733-1 GUARD
768521-2 LINK
1725732-1 NEST, Wire Ferrule
3-23620-3 PIN, Retain, Grvd, 1/4 x .894
1
1
1
2
2
2
7
6-23629-0 PIN, Retain, Grvd, 5/16 x 1.488
21045-6 RING, Retaining
1-21048-0 RING, Retaining
2
4
4
4
1
8†
9
10†
11 †
314479-6
679942-1
ROLLER
SPRING
6†
†Recommended Spares
Figure 6
4 of 4
Rev A
相关型号:
©2020 ICPDF网 联系我们和版权申明