2018875-2 [TE]
Mini-SAS HD Seating Tool Kit;
| 型号： | 2018875-2 |
| 厂家： | 
TE CONNECTIVITY |
| 描述： | Mini-SAS HD Seating Tool Kit |
| 文件： | 总4页 (文件大小：84K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Instruction Sheet
Mini-SAS HD Seating Tool Kit
2018875-1, 2018875-2, and 2018875-3
408-32028
08 FEB 12 Rev A
Seating Tool Bottomed
on Cage Assembly
1 X 1 Mini-SAS HD
Connector and Cage
Assembly 2149027-1
(Shown)
Wall Support Tool
(Shown Uninstalled for Clarity)
SEATING
TOOL
KIT NUMBER
MINI-SAS HD
CONNECTOR AND CAGE
CONFIGURATION
Printed Circuit Board (Ref)
Printed Circuit Board (Ref)
2018875-1
2018875-2
2018875-3
1 x 1
1 x 2
1 x 4
Figure 1
damage. The wall support supports the individual
port(s) of the cage assembly to prevent the cage
assembly from collapsing.
1. INTRODUCTION
Mini-SAS HD Seating Tool Kits 2018875-[ ] are used to
seat the Mini-SAS HD connector and cage assembly
configurations given in Figure 1 onto the printed circuit
(pc) board. The connector and cage assemblies
contain press-fit contacts to allow solderless pc board
installation.
3. ASSEMBLY PROCEDURE
3.1. PC Board Support Fixture (Customer Supplied)
A pc board support must be used to provide proper
support for the pc board and to protect the pc board
and product from damage. The support fixture must be
designed for specific needs using the following
recommendations:
Read these instructions thoroughly before using the
seating tool kit.
Dimensions in this instruction sheet are in
NOTE
millimeters [with inch equivalents i.n brackets].
Figures are not drawn to scale.
i
• It should be at least 25.4 mm [1 in.] longer and
wider than the pc board.
• It should have flat surfaces with holes or a channel
large enough and deep enough to receive any
protruding components of the connector and cage
assembly and to prevent the pc board from bowing.
2. DESCRIPTION
Each seating tool kit consists of a seating tool and a
wall support. The seating tool and wall support are
also available separately. The seating tool has cutouts
(three located on each side) to accept the protruding
parts of the cage assembly. The wall support must be
installed into the port(s) of the cage assembly. The top
of the seating tool provides a surface to accept the
force applied by the application tool to seat the
3.2. Application Tool
Power for seating tools must be provided by an
application tool (with a ram) capable of supplying a
downward force of 44.5 N [10 lb-force] per contact.
Manual Arbor Frame Assembly 58024-1 is available
for use with these seating tool kits. Refer to Instruction
Sheet 408-6923 for operating procedure.
connector and cage assembly onto the pc board.
During seating, the back and sides of the seating tool
protect the connector and cage assembly from
©2012 Tyco Electronics Corporation, a TE Connectivity Ltd. Company TOOLING ASSISTANCE CENTER 1-800-722-1111
All Rights Reserved
*Trademark
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.te.com
1 of 4
PRODUCT INFORMATION 1-800-522-6752
LOC B
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.
408-32028
Over-driving of the connector and cage assembly
will deform parts critical to the quality of the
connection. Maximum force occurs prior to the
connector and cage assembly bottoming on the pc
board.
cage assembly standoffs and the pc board is
CAUTION
allowed.
NOTE
i
Use the tool seating height as a reference starting
point. This height may need to be adjusted to
obtain the amount allowed (maximum of 0.10 mm
[.004 in.]) between the standoffs of the cage
assembly and the pc board.
!
4. SETUP
When setting up equipment to seat the connector and
cage assembly, pay particular attention to the
following:
2. Slide the wall support into the port(s) of the cage
assembly until the wall support is secure.
5. SEATING (see Figure 2)
• The seating tool must be matched to the
connector and cage assembly.
1. Place the pc board on the support fixture.
2. Orient the seating tool over the cage assembly so
that the back is aligned with the back of the cage
assembly. Then lower the seating tool onto the cage
assembly, making sure that the cutouts slide over
the protruding components of the cage assembly,
until the seating tool bottoms on the top of the cage
assembly.
If the seating tool and connector and cage
assembly are mismatched or are improperly
aligned, damage could occur to the tooling,
connector and cage assembly, or both.
CAUTION
!
• The wall support must be properly installed, and
the seating tool, connector and cage assembly, and
application tool ram must be properly aligned before
cycling the application tool
3. Place the connector and cage assembly on the
pc board so that the contacts are aligned and
started into the matching holes in the pc board.
4. Center the seating tool (with the connector and
cage assembly) under the ram of the application
tool. Slowly lower the ram until it just meets the
seating tool. Verify alignment of pc board support,pc
board, connector and cage assembly, and seating
tool.
1. Set tool seating height to the dimension shown in
Figure 2 (application tool shut height will equal the
tool seating height PLUS the combined thicknesses
of the pc board and support fixture). After seating, a
gap of no more than 0.10 mm [.004 in.] between the
Ram of Application
Tool (Fully Down)
Seating Tool 2018875-1
Cage Assembly
Wall Support (Installed in
Ports of Cage Assembly)
Application Tool Shut Height
(Ram Fully Down)
Press-Fit Contacts Inserted
into Holes in PC Board
Suport Fixture
0.1 mm (Max)
Gap Allowed
Printed Circuit (PC) Board
PC Board Support Fixture
Figure 2
2 of 4
Rev A
408-32028
Damage to the pc board, seating tool, or connector
and cage assembly may occur if the seating tool is
not properly seated on the connector and cage
assembly before cycling the application tool
necessary. Parts other than those listed should be
CAUTION
replaced by TE Connectivity to ensure quality and
reliability. Order replacement parts through your
representative, or call 1-800-526-5142, or send a
facsimile of your purchase order to 717--986--7605, or
write to:
!
5. Cycle the application tool to seat the connector
and cage assembly on the pc board. Then retract
the ram, and carefully remove the seating tool by
pulling it straight from the cage assembly
CUSTOMER SERVICE (038-035)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
6. Remove the wall support from the cage
HARRISBURG PA 17105-3608
7. Check the connector and cage assembly for
proper seating according to the following:
8. REVISION SUMMARY
a. the widest section of each compliant pin is
inside its intended pc board hole
This document supersedes 408-127007. New release
of 408-32028.
b. the connector and cage assembly is seated on
the pc board with a seating height-measured from
the top of the cage assembly (not including the)
to the top of the pc board- given in Figure 2
c. if present, the gap between the standoffs and
the pc board is no more than 0.10 mm [.004 in.]
For detailed application requirements of the
connector and cage assembly, refer to the relative
NOTE
application specification.
i
6. MAINTENANCE AND INSPECTION
The seating tool inspected before shipment. It is
recommended that the seating tool be inspected
immediately upon arrival at your facility to ensure that
it has not been damaged during shipment, and that it
conforms to the dimensions provided in Figure 3.
6.1. Daily Maintenance
It is recommended that each operator be made aware
of, and responsible for, the following steps of daily
maintenance.
1. Remove dust, moisture, and contaminants with a
clean, soft brush or a lint-free cloth. DO NOT use
objects that could damage the components.
2. When the seating tool and wall support are not in
use, store them in a clean, dry area.
6.2. Periodic Inspection
Regular inspections should be performed by quality
control personnel. A record of scheduled inspections
should remain with the seating tool or be supplied to
personnel responsible for the seating tool kit.
Inspection frequency should be based on amount of
use, working conditions, operator training and skill,
and established standards.
7. REPLACEMENT AND REPAIR
Customer-replaceable parts are listed in Figure 3. A
complete inventory should be stocked and controlled
to prevent lost time when replacement of parts is
3 of 4
Rev A
408-32028
Wall Support
( 1 X 4 Shown)
Seating Tool
(1 X 4 Shown)
REPLACEMENT PARTS
ITEM PART NUMBER (By Cage Assembly Configuration)
ITEM DESCRIPTION
QTY PER KIT
1 X 1
1 X 2
1 X 4
Seating Tool
Wall Support
2018876-1
2018877-1
2018876-2
2018877-2
2018876-3
2018877-3
1
1
DIMENSIONS (mm [In.])
CAGE ASSEMBLY
CONFIGURATION
A
B
C
D
E
F
1 X 1
1 X 2
1 X 4
18.2 [0717]
29.2 [1.50]
51.2 [2.016]
10.35 [0.407]
21.35 [0.841]
43.35 [1.707]
31 [1.220]
33 [1.299]
40 [1.575]
10.5 [0.413]
Figure 3
4 of 4
Rev A
相关型号：
©2020 ICPDF网 联系我们和版权申明