2215061-1 [TE]
Small Form-Factor Pluggable;
| 型号： | 2215061-1 |
| 厂家： | 
TE CONNECTIVITY |
| 描述： | Small Form-Factor Pluggable |
| 文件： | 总4页 (文件大小：286K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Instruction Sheet
Small Form-Factor Pluggable (zSFP+ with
EMI Springs or Enhanced) Surface Mount
Cage Assembly Seating Tool 2215061-[ ]
408-32165
10 FEB 15 Rev A
Seating Tool 2215061-1 (Shown)
1 X 4 Seating Tool
(Bottomed on Cage Assembly)
Compliant Pin
Contact
Back of Seating
Tool
Enhanced 1 X 4 Cage
Assembly (Shown)
Printed Circuit
(PC) Board (Ref)
PC Board Support
Fixture (Ref)
zSFP+ CAGE
SEATING
APPLICATION
SPECIFICATION
ASSEMBLY
1 X 4 Wall Support
(For Clarity, Not
Shown Installed)
TOOL KIT
CONFIGURATION
2215061-1
2215061-2
2215061-3
2215061-4
2215061-5
2215061-6
1 X 1
1 X 2
1 X 3
1 X 4
1 X 5
1 X 6
114-13120
NOTE: Connector Not Shown
Figure 1
1. INTRODUCTION
zSFP+ surface mount PT connector and cage assembly seating tool kits listed in Figure 1 are used to seat the
cage assemblies described in Figure 1 onto the pc board. The cage assembly contains compliant pin contacts
to allow solderless pc board installation. The seating tool is not designed to seat the connector.
Read these instructions thoroughly before using the seating tool kit.
NOTE
Dimensions on this sheet are in metric units [with U.S. customary units in brackets]. Figures and illustrations are for reference
only and are not drawn to scale.
2. DESCRIPTION (Figure 1)
Each seating tool kit consists of a seating tool and a wall support. The seating tool and wall support are also
available separately. The seating tool has cutouts (two located on each side) to accept the protruding part of
the standoffs of the cage assembly. The wall support must be installed into the ports of the cage assembly.
The top of the seating tool provides a surface to accept the force applied by the application tool to seat the
product onto the pc board. During seating, the back and sides of the seating tool protect the cage assembly
from damage. The wall support supports the individual ports of the cage assembly.
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.te.com.
© 2015 TE Connectivity family of companies
All Rights Reserved
*Trademark
TOOLING ASSISTANCE CENTER 1-800-722-1111
PRODUCT INFORMATION 1-800-522-6752
1 of 4
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.
408-32165
3. REQUIREMENTS
3.1. PC Board Support Fixture (Customer Supplied)
A pc board support must be used to provide proper support for the pc board and to protect the pc board and
the connector and cage assembly from damage. The support fixture must be designed for specific needs using
the following recommendations:
it should be at least 25.4 mm [1 in.] longer and wider than the pc board
it should have flat surfaces with holes or a channel large enough and deep enough to receive any
protruding components of the product
3.2. Application Tool
Power for seating tools must be provided by an application tool (with a ram) capable of supplying a downward
force of 44.5 N [10 lb-force] per contact. For available application tools, call PRODUCT INFORMATION at the
number at the bottom of page 1.
CAUTION
Over-driving of the cage assembly will deform parts critical to the quality of the connection. Maximum force occurs prior to the
cage assembly bottoming on the pc board.
4. SETUP
When setting up equipment to seat the cage assembly, pay particular attention to the following:
the seating tool must be matched to the cage assembly
CAUTION
If the seating tool and cage assembly are mismatched or are improperly aligned, damage could occur to the tooling, cage
assembly, or both.
light pipes MUST NOT be assembled onto the cage assembly
the wall support must be properly installed, and the seating tool, cage assembly, and application tool ram
must be properly aligned before cycling the application tool
1. Set the tool seating height to the dimension shown in Figure 2 (application tool shut height will equal
the tool seating height PLUS the combined thicknesses of the pc board and support fixture).
Ram of Application
Tool (Fully Down)
Seating Tool
Tool Seating Height
Wall Support (Installed in
(With Cage
Ports of Cage Assembly
Assembly Seated)
Compliant Pin Contacts (and Any
Protruding Components) Inserted into
Application Tool
Shut Height
(Ram Fully Down)
(See Section 4,
0.10 [.004] (Max)
Holes in PC Board and PC Board
Gap Allowed
Support Fixture
Step 1)
PC Board
PC Board
Support Fixture
Figure 2
After seating, a gap of no more than 0.10 mm [.004 in.] between the cage assembly standoffs and the
pc board is allowed.
NOTE
Use the tool seating height as a reference starting point. This height may need to be adjusted to obtain the amount allowed
(maximum of 0.10 mm [.004 in.]) between the standoffs of the cage assembly and the pc board.
2 of 4
Rev A
408-32165
2. Slide the wall support into the ports of the cage assembly until the wall support is secure.
5. SEATING (Figure 2)
NOTE
The connector must be mounted on the pc board BEFORE seating the cage assembly.
1. Place the pc board on the support fixture.
2. Orient the seating tool over the cage assembly so that the back is aligned with the back of the cage
assembly. Then lower the seating tool onto the cage assembly, making sure that the cutouts slide
over the protruding components of the cage assembly, until the seating tool bottoms on the top of the
cage assembly.
3. Place the cage assembly on the pc board so that the contacts and alignment posts are aligned and
started into the matching holes in the pc board.
4. Center the seating tool (with the cage assembly) under the ram of the application tool. Slowly lower
the ram until it just meets the seating tool. Verify alignment of pc board support, pc board, cage
assembly, and seating tool.
CAUTION
Damage to the pc board, seating tool, or cage assembly may occur if the seating tool is not properly seated on the cage
assembly before cycling the application tool.
5. Cycle the application tool to seat the cage assembly on the pc board. Then retract the ram, and
carefully remove the seating tool by pulling it straight from the cage assembly.
6. Check the cage assembly for proper seating according to the following:
a. the widest section of each compliant pin is inside its intended pc board hole
b. each alignment post is in its intended pc board hole
c. if present, the gap between the standoffs and the pc board is no more than 0.10 mm [.004 in.]
NOTE
For detailed application requirements of the cage assembly, refer to the application specification given in Figure 1.
6. MAINTENANCE AND INSPECTION
The seating tool kit is assembled and inspected before shipment. It is recommended that the seating tool kit be
inspected immediately upon arrival at your facility to ensure that it has not been damaged during shipment, and
that it conforms to the dimensions provided in Figure 3.
6.1. Daily Maintenance
It is recommended that each operator be made aware of, and responsible for, the following steps of daily
maintenance:
1. Remove dust, moisture, and contaminants with a clean, soft brush or a lint-free cloth. DO NOT use
objects that could damage the components.
2. When the seating tool and wall support are not in use, store them in a clean, dry area.
6.2. Periodic Inspection
Regular inspections should be performed by quality control personnel. A record of scheduled inspections
should remain with the seating tool or be supplied to personnel responsible for the seating tool kit. Inspection
frequency should be based on amount of use, working conditions, operator training and skill, and established
standards.
7. REPLACEMENT AND REPAIR
Customer-replaceable parts are listed in Figure 3. A complete inventory should be stocked and controlled to
prevent lost time when replacement of parts is necessary. Parts other than those listed should be replaced by
TE Connectivity to ensure quality and reliability. Order replacement parts through your TE Representative, or
call 1-800-526-5142, or send a facsimile of your purchase order to 717-986-7605, or write to:
3 of 4
Rev A
408-32165
CUSTOMER SERVICE (038-035)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
HARRISBURG PA 17105-3608
8. REVISION SUMMARY
Initial release of document
Seating Tool 2215061-4 (1 X 4 Shown)
Top
F
B
E
G
A
Side
Front
C
SEATING TOOL
KIT ( By Cage
DIMENSION
Assembly
Configuration)
A
B
C
E
F
G
1 X 1
1 X 2
1 X 3
1 X 4
1 X 5
1 X 6
18.00 [.709]
32.70 [1.287]
47.00 [1.850]
61.20 [2.409]
75.40 [2.968]
88.90 [3.500]
13.64 [.537]
27.94 [1.100]
42.16 [1.660]
56.39 [2.220]
70.66 [2.782]
84.33 [3.320]
41.10 [1.618]
21.00 [.827]
8.38 [.330]
50.8 [2.00]
Figure 3 (end)
4 of 4
Rev A
相关型号：
©2020 ICPDF网 联系我们和版权申明