2215880-1 [TE]
Small Form-Factor Pluggable;
| 型号： | 2215880-1 |
| 厂家： | 
TE CONNECTIVITY |
| 描述： | Small Form-Factor Pluggable |
| 文件： | 总4页 (文件大小：319K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Instruction Sheet
Small Form-Factor Pluggable (SFP+ EMI
Gasket with Heat Sink and Light Pipe)
Cage Assembly Seating Tool 2215085-[ ]
408-32217
23 DEC 15 Rev A
1 X 4 Seating Tool
(Bottomed on Cage
Assembly)
Back of
Seating Tool
1 X 4 Cage Assembly
2198243-6
1 X 4 Single-Piece Wall
Support (For Clarity, Not
Shown Installed)
Compliant Pin
Contact
PC Board Support
Fixture (Ref)
SFP+ CAGE
ASSEMBLY
CONFIGURATION
SEATING
TOOL KIT
APPLICATION
SPECIFICATION
Printed Circuit
(PC) Board (Ref)
2215085-1
2215085-2
1 X 4
114-13120
Figure 1
1. INTRODUCTION
SFP+ cage assembly seating tool listed in Figure 1 is used to seat the cage assembly described in Figure 1
onto the pc board. The cage assembly contains compliant pin contacts to allow solderless pc board installation.
Read these instructions thoroughly before using the seating tool kit.
NOTE
Dimensions on this sheet are in metric units [with U.S. customary units in brackets]. Figures and illustrations are for reference
only and are not drawn to scale.
2. DESCRIPTION (Figure 1)
Each seating tool consists of a seating tool and a wall support. The seating tool has cutouts (two located on
each side) to accept the protruding part of the standoffs of the cage assembly. The wall support must be
installed into the ports of the cage assembly.
The top of the seating tool provides a surface to accept the force applied by the application tool to seat the
product onto the pc board. During seating, the back and sides of the seating tool protect the cage assembly
from damage. The wall support supports the individual ports of the cage assembly.
3. REQUIREMENTS
3.1. PC Board Support Fixture (Customer Supplied)
A pc board support must be used to provide proper support for the pc board and to protect the pc board and
the connector and cage assembly from damage. The support fixture must be designed for specific needs using
the following recommendations:
it should be at least 25.4 mm [1 in.] longer and wider than the pc board
it should have flat surfaces with holes or a channel large enough and deep enough to receive any
protruding components of the product
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.te.com.
© 2015 TE Connectivity family of companies
All Rights Reserved
*Trademark
PRODUCT INFORMATION 1-800-522-6752
1 of 4
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.
408-32217
3.2. Application Tool
Power for seating tools must be provided by an application tool (with a ram) capable of supplying a downward
force of 44.5 N [10 lb-force] per contact. For available application tools, call PRODUCT INFORMATION at the
number at the bottom of page 1.
CAUTION
Over-driving of the cage assembly will deform parts critical to the quality of the connection. Maximum force occurs prior to the
cage assembly bottoming on the pc board.
4. SETUP
When setting up equipment to seat the cage assembly, pay particular attention to the following:
the seating tool must be matched to the cage assembly
CAUTION
If the seating tool and cage assembly are mismatched or are improperly aligned, damage could occur to the tooling, cage
assembly, or both.
light pipes MUST NOT be assembled onto the cage assembly
the wall support must be properly installed, and the seating tool, cage assembly, and application tool ram
must be properly aligned before cycling the application tool
1. Set the tool seating height to the dimension shown in Figure 2 (application tool shut height will equal
the tool seating height PLUS the combined thicknesses of the pc board and support fixture).
Ram of Application
Application Tool
Shut Height (Ram
Fully Down) (See
Section 4, Step 1)
Seating
Tool
Tool Seating Height
26.63 [1.048] with
Cage Assembly Seated
Tool (Fully Down)
Wall Support
(Installed in
Ports of Cage
Assembly)
Compliant Pin Contacts
(and Any Protruding
Components) Inserted into
Holes in PC Board and PC
Board Support Fixture
0.10 [.004]
(Max) Gap
Allowed
PC Board
PC Board
Support Fixture
Figure 2
After seating, a gap of no more than 0.10 mm [.004 in.] between the cage assembly standoffs and the
pc board is allowed.
NOTE
Use the tool seating height as a reference starting point. This height may need to be adjusted to obtain the amount allowed
(maximum of 0.10 mm [.004 in.]) between the standoffs of the cage assembly and the pc board.
2. Slide the wall support into the ports of the cage assembly until the wall support is secure.
5. SEATING (Figure 2)
NOTE
The connector must be mounted on the pc board BEFORE seating the cage assembly.
2 of 4
Rev A
408-32217
1. Place the pc board on the support fixture.
2. Orient the seating tool over the cage assembly so that the back is aligned with the back of the cage
assembly. Then lower the seating tool onto the cage assembly, making sure that the cutouts slide
over the protruding components of the cage assembly, until the seating tool bottoms on the top of the
cage assembly.
3. Place the cage assembly on the pc board so that the contacts and alignment posts are aligned and
started into the matching holes in the pc board.
4. Center the seating tool (with the cage assembly) under the ram of the application tool. Slowly lower
the ram until it just meets the seating tool. Verify alignment of pc board support, pc board, cage
assembly, and seating tool.
CAUTION
Damage to the pc board, seating tool, or cage assembly may occur if the seating tool is not properly seated on the cage
assembly before cycling the application tool.
5. Cycle the application tool to seat the cage assembly on the pc board. Then retract the ram, and
carefully remove the seating tool by pulling it straight from the cage assembly.
6. Check the cage assembly for proper seating according to the following:
a. the widest section of each compliant pin is inside its intended pc board hole
b. each alignment post is in its intended pc board hole
c. if present, the gap between the standoffs and the pc board is no more than 0.10 mm [.004 in.]
NOTE
For detailed application requirements of the cage assembly, refer to the application specification given in Figure 1.
6. MAINTENANCE AND INSPECTION
The seating tool kit is assembled and inspected before shipment. It is recommended that the seating tool kit be
inspected immediately upon arrival at your facility to ensure that it has not been damaged during shipment, and
that it conforms to the dimensions provided in Figure 3.
6.1. Daily Maintenance
It is recommended that each operator be made aware of, and responsible for, the following steps of daily
maintenance:
1. Remove dust, moisture, and contaminants with a clean, soft brush or a lint-free cloth. DO NOT use
objects that could damage the components.
2. When the seating tool and wall support are not in use, store them in a clean, dry area.
6.2. Periodic Inspection
Regular inspections should be performed by quality control personnel. A record of scheduled inspections
should remain with the seating tool or be supplied to personnel responsible for the seating tool kit. Inspection
frequency should be based on amount of use, working conditions, operator training and skill, and established
standards.
7. REPLACEMENT AND REPAIR
Customer-replaceable parts are listed in Figure 3. Parts other than those listed should be replaced by TE to
ensure quality and reliability. For customer repair service or to order replacement parts, call 1-800-522-6752, or
fax your purchase order to 717-986-7605, or write to: Customer Service (038-035), Tyco Electronics
Corporation, PO Box 3608, Harrisburg, PA 17105-3608.
8. REVISION SUMMARY
Initial release of document
3 of 4
Rev A
408-32217
11
3
Seating Tool 2215085-[ ]
Top
1
Single Piece Wall Support
Front
Side
G
2
8
F
A
E
B
11
6
Front
End
10
5
4
9
C
7
DIMENSION
SEATING
TOOL
A
B
C
E
F
G
2215085-1
2215085-2
45.0 [1.77]
44.5 [1.75]
28.5 [1.12]
31.3 [1.23]
60.8 [2.39]
56.0 [2.21]
8.4 [.33]
50.8 [2.00]
REPLACEMENT PARTS
QTY PER KIT
2215085-1 2215085-2
ITEM NUMBER
PART NUMBER
DESCRIPTION
1
2
2215818-5
2215876-1
2215878-1
2215878-2
2215879-1
2215879-2
2215880-1
2215880-2
2215877-1
2215877-2
2215881-1
2215881-2
18024-2
Wall Support
Center Block
1
1
1
1
1
3
4
5
6
7
Rear Plate
1
1
1
1
1
1
1
3
Right Side Plate
Left Side Plate
Front Plate
Plate, Insert
3
8
2
2
4
8
9
Screw, Btn Head Cap
Pin, Dowel
8
2
2
4
7-992946-7
2-992946-4
1-992946-4
10
11
Pin, Dowel
Pin, Dowel
Figure 3
4 of 4
Rev A
相关型号：
©2020 ICPDF网 联系我们和版权申明