312156-1 [TE]

Pistol Grip Pneumatic Handle Assembly;


型号：	312156-1
厂家：	TE CONNECTIVITY
描述：	Pistol Grip Pneumatic Handle Assembly
文件：	总5页 (文件大小：268K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Instruction Sheet



Pistol Grip Pneumatic

Handle Assembly 58075-1

408-6789

25 JUL 11 Rev E

PROPER USE GUIDELINES

Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use

and low volume applications. A wide selection of powered application equipment for extended-use, production operations is available.

personal injury, as well as damage to the equipment.

For best results, application equipment must be

operated in a dry, dust-free environment. Do not

operate equipment in a gaseous or hazardous

environment.

Carefully observe the following safety precautions

before and during operation of the equipment:

• ALWAYS wear appropriate ear protection.

• ALWAYS wear approved eye protection when

operating powered equipment.

• ALWAYS keep guard(s) in place during normal

operation.

• ALWAYS disconnect the tool from its power

source when performing maintenance on the

equipment.

• NEVER wear loose clothing or jewelry that may

catch in moving parts of the application equipment.

• NEVER insert hands into installed application

equipment.

• NEVER alter, modify, or misuse the application

Figure 1

equipment.

1. INTRODUCTION

2.2. Contact



These instructions deal with the safety, installation,

operation and maintenance of the Pistol Grip

Pneumatic Handle Assembly 58075-1. See Figure 1.

CALL TOLL FREE 1-800-722-1111 (CONTINENTAL

UNITED STATES AND PUERTO RICO ONLY)

The Tooling Assistance Center offers a means of

providing technical assistance when required.

Pistol Grip Pneumatic Handle Assembly 58075-1

accepts interchangeable terminating heads that

terminate wires in connectors. To ensure accurate

termination of wires, setup adjustments, and head

maintenance, refer to the instructions packaged with

the terminating head.

In addition, Field Service Specialists are available to

provide assistance in the adjustment or repair of the

application equipment when problems arise which

your maintenance personnel are unable to correct.

Dimensions in this instruction sheet are in metric

units [with U.S. customary units in brackets].

Figures are for reference only and are not drawn to

scale.

When calling the Tooling Assistance Center regarding

service to equipment, it is suggested that a person

familiar with the device be present with a copy of the

manual (and drawings) to receive instructions. Many

difficulties can be avoided in this manner.

NOTE

Reasons for reissue of this instruction sheet are

provided in Section 9, REVISION SUMMARY.

When calling the Tooling Assistance Center, be ready

with the following information:

2. SAFETY PRECAUTIONS AND COMPANY CONTACT

2.1. Safety

1. Customer name

2. Customer address

Safeguards are designed into this application

equipment to protect operators and maintenance

personnel from most hazards during equipment

operation. However, certain safety precautions must

be taken by the operator and repair personnel to avoid

3. Person to contact (name, title, telephone number,

and extension)

4. Person calling

*Trademark



This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com

1 of 5

PRODUCT INFORMATION 1-800-522-6752

LOC B

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.

408-6789

5. Equipment number (and serial number if

applicable)

8. Nature of problem

9. Description of inoperative component(s)

6. Product part number (and serial number if

applicable)

10. Additional information/comments that may be

helpful

7. Urgency of request

2 of 5

Rev E

408-6789

Read these instructions thoroughly before operating

any of the pneumatic tools. The performance of these

tools will depend largely upon the intelligent use of

information contained in this manual and pay

particular attention to DANGER, CAUTION, and

NOTE statements.

4. HEAD INSTALLATION AND REMOVAL

To avoid personal injury, ALWAYS disconnect

handle assembly from the air supply when installing

or removing the terminating head.

DANGER

STOP

1. Disconnect and/or lockout the tool from its air

supply.

Denotes an imminent hazard which may result in

moderate or severe injury.

DANGER

STOP

2. Position the blade tip of a screwdriver between

the shoulder of the key and the handle assembly

body. Pry and remove the key.



CAUTION

3. Insert the terminating head into the head

entrance until the head bottoms. See Figure 3.

Denotes a condition which may result in product or

equipment damage.

Key

Highlights special or important information.

NOTE

Terminating

Head (Ref)

3. DESCRIPTION

The pneumatic handle assembly features a molded

nylon handle with a trigger and an air tube. The handle

holds an air cylinder with a key which retains the

terminating head in the body and allows the head to

be rotated. Refer to Figure 2.

Head Entrance

In this use, the handle assembly noise level with the

terminating head emits a maximum of 78 dB, and the

vibration level is less than 2.5 mm/s².

Figure 3

Air Cylinder

Body

4. Re-insert the key to retain the head.

5. To remove the head, remove the key and pull the

head out of the handle assembly.

Key (Visible on

this Side)

5. SETUP

It is recommended that a regulator-filter-lubricator unit

with the lubricator adjusted to the minimum setting be

used with the handle assembly. Refer to Figure 4.

Handle

It is also recommended that quick-disconnect fittings

are used to connect the tool to the air supply. If not

using quick-disconnect fittings, provide a pneumatic

lock-out on the air line that bleeds air after it is turned

off.

Trigger

The handle assembly is designed to operate with an

air pressure range of 276 to 483 kPa [40 to 70 psi].

Service life can be greatly extended when only the

necessary air pressure is applied. Excessive pressure

causes wear and strain on handle assembly

components and the connectors.

Air Tube

Do not use this tool as a blunt object, a crushing

device, or for any purpose other than crimping the

CAUTION

proper specified product. Inappropriate use of the

tool could result in personal injury or damage to the

tool.

Figure 2

3 of 5

Rev E

408-6789

Lubricator

Filter and Moisture

Separator

To Machine

Airflow

Regulator

Figure 4

3. The degree of operator skill.

6. OPERATION

The following procedure provides only general

information concerning crimping. Refer to the

instructions packaged with the terminating heads for

detailed information including wire stripping

dimensions and instructions for positioning terminals

in the terminating heads.

4. Your own established standards.

The handle assembly is inspected before being

shipped; however, it is recommended that the handle

assembly be inspected immediately upon arrival to

ensure that the handle assembly has not been

damaged during shipment.

1. Insert the connector into the left side of the head.

7.1. Daily Maintenance

2. Align the contact to be terminated with the wire

inserter of the head. Make sure that the locating

pawl rests between the connector index ribs.

Each operator should be aware of, and responsible

for, the following:

1. Remove dust, moisture, and other contaminants

with a clean brush, or soft, lint-free cloth. DO NOT

use objects that could damage the handle

assembly.

3. Insert an unstripped wire into the funnel area

between the contact and the wire inserter until it

bottoms on the tool base.

4. Depress the trigger of the handle assembly and

hold it until the wire inserter bottoms.

2. Ensure that all components are in place and

properly secured.

5. Release the trigger. The wire inserter will retract

and the feed slide will automatically advance the

connector to the next contact position.

3. With the terminating head in place, connect the

air supply, then squeeze and release the trigger to

ensure that the mechanisms and plunger move

smoothly.

6. Repeat steps 2 through 5 until all contacts have

been terminated.

7.2. Periodic Inspection (At Least Once a Month)

7. Inspect each termination.

1. Remove any accumulated film with a suitable

cleaning agent that will not affect plastic material.

7. MAINTENANCE AND INSPECTION

To avoid personal injury, ALWAYS disconnect the

handle assembly from the air supply when

performing maintenance or inspection procedures.

DANGER

2. Make sure all components are in place and are

properly secured. Refer to Figure 5. Check the

handle assembly for chipped, cracked, worn, or

broken areas. If damage is evident, repair is

necessary. See Section 8, REPLACEMENT AND

REPAIR.

STOP

It is recommended that a maintenance and inspection

program be performed periodically to ensure

dependable and uniform terminations. Though

recommendations call for at least one inspection a

month, frequency of inspection depends on:

8. REPLACEMENT AND REPAIR

Customer-replaceable parts are listed in Figure 5.

A complete inventory can be stocked and controlled to

prevent lost time when replacement of parts is

necessary. Parts other than those listed should be

replaced by TE to ensure quality and reliability of the

handle assembly. Order replacement parts through

1. The care, amount of use, and handling of the

handle assembly.

2. The presence of abnormal amounts of dust and

dirt.

4 of 5

Rev E

408-6789

your representative, or call 1-800-526-5142, or send a

facsimile of your purchase to 717-986-7605, or write

to:

TYCO ELECTRONICS CORPORATION UK LTD

BARTON TORS 

BIDEFORD 

NORTH DEVON, GREAT BRITAIN

CUSTOMER SERVICE (038-035)

TYCO ELECTRONICS CORPORATION

PO BOX 3608

For customer repair service, call 1-800-526-5136.

HARRISBURG PA 17105-3608

9. REVISION SUMMARY

Since the previous release of these instructions, the

new company logo was applied, and the document

was re-formatted and re-arranged.

ITEM

PART NUMBER

27174-1

DESCRIPTION

VALVE, Poppet

QTY PER ASSEMBLY

1-21003-3

28472-1

SCREW, Flat Head Socket Cap

PUSH BUTTON TRIGGER, Valve Actuator

KEY

312140-1

312141-1

312157-1

21086-6

NUT, Cam Adjustment

AIR CYLINDER

O-RING

310421-1

310424-1

312156-1

312622-2

217915-1

PLUG, Cap

BRACKET, Air Cylinder

HANDLE

SUBASSEMBLY, Air Tube

LABEL, CE

Figure 5

5 of 5

Rev E

312156-1 [TE]

相关型号：

312157-1

312158-2

312159-1

312160-1

312160-1

312161-1

312161-1

312175

312187

3121CP-8

3122

3122-1-00-1-00-00-08-0