350694 [TE]

Extraction Tool 2063388- 1;


型号：	350694
厂家：	TE CONNECTIVITY
描述：	Extraction Tool 2063388- 1
文件：	总2页 (文件大小：90K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Instruction Sheet

408-10376

Extraction Tool 2063388-1

23 Mar 11 Rev B

PROPER USE GUIDELINES

Cumulative Trauma Disorders can resultfrom the prolonged use ofmanually powered hand tools. Hand tools are intended for occasional use and low volume

applications. A wide selection of powered application equipment for extended-use, production operations is available.

Handle

Sheet 408--9501. The pin and socket contacts are

listed by part number in Figure 1. Read these

instructions thoroughly before attempting to remove

any contacts from the housings.

Dimensions on this sheet are in millimeters [with

inch equivalent dimensions in brackets]. Figures

and illustrations are for identification only and are

not drawn to scale.

NOTE

Tip

Plunger

2. DESCRIPTION

PART NUMBERS

FOR MINIATURE RECTANGULAR (MR) CONTACTS

PIN SOCKET

The tool consists of a metal tip and a plastic handle. The

tip is inserted into the mating face of the housing,

depressing the locking lances of the crimped contact.

This action allows the contact to be extracted from the

wire--entry face of the housing.

STRIP

350018

350171

350183

350663

350684

350694

350968

350967

STRIP

350019

350184

350665

350696

-- -- --

350036

350197

350185

350664

350685

350695

640579

640545

350037

350186

350666

350697

-- -- --

3. EXTRACTION PROCEDURE

The procedures which follow are recommended to

extract a crimped contact from a housing. See Figures

2 and 3.

-- -- --

Proceed as follows:

641294

-- -- --

641300

-- -- --

1. Grasp wire of contact to be removed. Push

contact toward mating face of connector and hold

in this position. This will disengage contact locking

lance from shoulder of cavity.

FOR MINIATURE UNIVERSAL MATE-N-LOK* CONTACTS

PIN SOCKET

STRIP

170359

170360

171636

STRIP

170361

170362

171637

2. While holding wire, place tool releasing barrel

over end of contact and push straight into cavity

until it bottoms. The locking lance is now released.

170363

170364

171638

170365

170366

171639

3. Keep releasing barrel firmly bottomed in cavity

and depress plunger (handle). Contact will partially

eject.

FOR COMMERCIAL PIN .062 CONTACTS

STRIP

350629

640391

-- -- --

If difficulty is encountered in pushing contact

forward, Insertion Tool 91002 -1 (tweezer type),

may be used to perform the task from the wire

side of the housing.

NOTE

Figure 1

1. INTRODUCTION

4. Pull contact from BACK of connector and

remove tool from cavity.

Extraction Tool 2063388--1, Figure 1, is designed to

remove Miniature Rectangular (MR) contacts,

Miniature Universal MATE--N--LOK contacts, or

Commercial .062 pin contacts from the housings

designed for these contacts. Information for the

removal of Commercial .062 socket contacts with

Extraction Tool 844134--1 can be found on Instruction

Before inserting contact into housing, reset

locking lances to their original positions. Consult

the Customer Drawing covering the specific

contact removed (or consult TE Connectivity

Engineering) for correct setting of locking lances.

NOTE

E2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company

TOOLING ASSISTANCE CENTER 1--800--722--1111 This controlled document is subject to change.

1 of 2

PRODUCT INFORMATION 1--800--522--6752

For latest revision and Regional Customer Service,

visit our website at www.te.com

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks.

*Trademark. Other logos, product and/or Company names may be trademarks of their respective owners.

LOC B

408-10376

Wire

Plug

Contact Cavity

Locking Lances

Plunger (Ref

Contact

Socket

Contact

Releasing Barrel

Figure 2

Figure 3

Additional tools can be purchased from:

4. MAINTENANCE AND INSPECTION

To ensure proper operation, the tool should conform

to the dimensions provided in Figure 4. It is

recommended that the tool be inspected immediately

on its arrival and at regularly scheduled intervals. The

tool is not repairable and should be replaced when

worn or damaged. It is recommended that the tool be

stored in a clean, dry place and cleaned with a soft,

lint--free cloth.

TYCO ELECTRONICS CORPORATION

CUSTOMER SERVICE (38--35)

P. O. BOX 3608

HARRISBURG, PA 17105--3608

5. REVISION SUMMARY

S Updated document to corporate requirements.

NOTE: Not to Scale

19.05 [.750] Ref

2.03 [.080] Ref

2.54 [.100] Ref

60.60 [2.386] Ref

Figure 4

2 of 2

Rev B

相关型号：