35221M0JT [TE]
SMD POWER RESISTORS â AEC-Q200 QUALIFIED;型号: | 35221M0JT |
厂家: | TE CONNECTIVITY |
描述: | SMD POWER RESISTORS â AEC-Q200 QUALIFIED |
文件: | 总7页 (文件大小:269K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
SMD POWER RESISTORS – AEC-Q200 QUALIFIED
Type 3522 Series
Key Features
3 Watts at
70°C
Small size to
power ratio
Supplied on
tape
Value marked
on resistor
Available via
distribution
500 volt
maximum
TE Connectivity is pleased to announce that our 3522 series resistor is now AEC-
overload
Q200 qualified. This low cost high power device, suitable for auto placement in
volume and for most applications, including high frequency operations, owing to
the short lead structure is supplied as standard on 7 inch Reels of 2000 pieces
per reel.
250 volt
working
voltage
Terminal finish
matte Sn over
Ni
Characteristics – Electrical
Power rating at 70°C
3W
AEC-Q200
Qualified
Rated current (Jumper)
Max. overload current (Jumper)
Max working voltage
2.5A
10A
250V
500V
Max overload voltage
Dielectric withstand voltage
Temperature range
500V
-55°C ~ +155°C
70°C
Ambient temperature
* Rated continuous working voltage (RCWV) shall be determined from
RCWV = √(Rated Power x Resistance Value), or Maximum RCWV listed above,
whichever is less
**Recommended Circuit Board Design - If this device is anticipated to run at full
continuous power then action to improve the cooling should be taken. This can
be a metal substrate, copper pad left under the chip, an opening in the PCB or
enlarged silver conductor pads each end.
Dimensions in
Dimensions Shown for
reference purposes only.
Specifications subject to
change
9-1773463-7 Rev. G 04/2020
For Email, phone or live chat,
go to: www.te.com/help
millimetres unless
otherwise specified
SMD POWER RESISTORS – AEC-Q200 QUALIFIED
Power derating curve
For resistors operated in ambient temperatures above 70°C, power rating
must be derated in accordance with this curve.
Construction and dimensions
L ± 0.10
6.35
W ± 0.15
3.20
H ± 0.10
1.10
ℓꢀ ± ꢁ.ꢂ5
0.60
ℓꢂ ± ꢁ.ꢂꢁ
1.80
Power rating
@70°C
Tolerance %
Resistance
Range
Standard series
Jumper
± 1%
± 5%
<5ꢁꢃΩ
ꢀΩ - 10MΩ
ꢀΩ - ꢀꢁMΩ
3W
E96
E24
Dimensions in
Dimensions Shown for
reference purposes only.
Specifications subject to
change
9-1773463-7 Rev. G 04/2020
For Email, phone or live chat,
go to: www.te.com/help
millimetres unless
otherwise specified
SMD POWER RESISTORS – AEC-Q200 QUALIFIED
Performance specification
Characteristics
Limits
Test Methods
125, at35% of operating power,
1000H(1.5 hours ꢇONꢈ, ꢁ.5 hour
ꢇOFFꢈꢅ. ꢄMIL-STD-202)
Applꢉ to rate curreꢊt for ꢁ Ω
Parametrically test per lot and
sample size requirements, summary
to show Min, Max, Mean and
Standard deviation at room as well as
Min and Max operating
±ꢄꢀ%+ꢁ.ꢀΩꢅꢃaꢆ
<ꢀꢁꢁꢃΩ
Operational life
1Ω ≤ R ≤10Ω ≤ ±400PPM/°C
10Ω< R ≤100Ω ≤ ±200PPM/°C
100Ω<R≤10MΩ ≤
Temperature
Coefficient of
Resistance
±100PPM/°C
temperatures. (User Spec)
Electrical test not required. Inspect
device construction, marking and
workmanship
External Visual
No Mechanical Damage
(MIL-STD-883 Method 2009)
Verify physical dimensions to the
applicable device detail specification
Note: User(s) and Suppliers spec.
Electrical test not required.
(JESD22 MH Method JB-100)
Note: Add Aqueous wash chemical –
OKEM Clean or equivalent.
Do not use banned solvents.
( MIL-STD-202 Method 215)
Force of 1.8kg for 60 seconds.
(JIS-C-6429)
Physical
dimension
Reference 2.0 Dimension
standards
Resistance to
solvent
Marking Unsmeared
Not broken
Terminal
Strength
1000hrs. @T=155°C.Unpowered.
Measurement at 24±2 hours after
test conclusion.
(MIL-STD-202 Method 108)
Applꢉ to rate curreꢊt for ꢁ Ω
High
±(1%+0.1Ω)max
Temperature
Exposure
(storage)
<5ꢁꢃΩ
1000 Cycles (-55°C to +155°C).
Measurement at 24±2 hours after
test conclusion
(JESD22 Method JA-104)
Applꢉ to rate curreꢊt for ꢁ Ω
Resistance change rate is
±ꢄꢁ.5%+ꢁ.ꢀΩꢅ Maꢆ
Temperature
cycling
<5ꢁꢃΩ
Resistance change rate is
± ꢄꢁ.5%+ꢁ.ꢀΩꢅ Maꢆ.
Moisture
Resistance
T=24 hours /cycle. Unpowered.
Measurement at 24±2 hours
after test conclusion.
(MIL-STD-202 Method 106)
Applꢉ to rate curreꢊt for ꢁ Ω
10% rated power, 85°C/85% RH,
1000H,
Measurement at 24 hours after test
conclusion
<5ꢁꢃΩ
Resistance change rate is
± ꢄꢀ%+ꢁ.ꢀΩꢅ Maꢆ.
Biased Humidity
(MIL-STD-202 Method 103)
Applꢉ to rate curreꢊt for ꢁ Ω
<ꢀꢁꢁꢃΩ
Dimensions in
Dimensions Shown for
9-1773463-7 Rev. G 04/2020
For Email, phone or live chat,
millimetres unless
otherwise specified
reference purposes only.
Specifications subject to
change
go to: www.te.com/help
SMD POWER RESISTORS – AEC-Q200 QUALIFIED
Characteristics
Limits
Test Methods
Wave Form: Tolerance for half sine
shock pulse. Peak value is ꢀꢁꢁg’s.
Normal duration (D) is 6.
Mechanical
Shock
±(1%+0.1Ω)max
(MIL-STD-202 Method 213)
5g’s for ꢂꢁ ꢃiꢊ., ꢀꢂcꢉcle each of ꢋ
orientations
Note: Use ꢌꢈ*5ꢈPCB. ꢁꢋꢀꢈ thick ꢍ
secure points on one long side and 2
secure points at corners of opposite
sides. Parts ꢃouꢊted withiꢊ ꢂ’ froꢃ
any secure point.
Vibration
±(1%+0.1Ω)max
Test from 10-2000Hz.
(MIL-STD-202 Method 204)
-55°C/+155°C, Note: Number of
cycles required - 300,
±(1%+0.1Ω)max
<50mΩ
Maximum transfer time -20 seconds,
Dwell time -15 minutes. Air-Air.
(MIL-STD-202 Method 107)
Apply to rate current for 0Ω
With the electrometer in direct
contact with the discharge tip, verify
the voltage setting at levels of
±500V, ±1KV, ±2KV, ±4KV, ±8KV, The
electrometer reading shall be within
±10% for voltages from 500V to
≦800V.
Thermal Shock
ESD
±(10%+0.1Ω)max
(AEC-Q200-002)
For both leaded & SMD. Electrical
test not required.
Magnification 50X. Conditions:
a) Method B 4hrs at 155°C dry heat,
the dip in bath with 245°C, 5s.
b) Method B: at 215°C, 5s.
c) Method D: at 260°C, 60s.
(J-STD-002)
Solderability
95% coverage Min.
No ignition of the tissue paper
or scorching of the pinewood
board
V-0 or V-1 are acceptable. Electrical
test not required.
(UL-94)
Flammability
Board Flex
±(1%+0.05Ω)max
<50mΩ
2mm (Min) (JIS-C-6429)
Apply to rate current for 0Ω
Temperature sensing at 500°C,
Voltage power subjected to 32VDC
current clamped up to 500ADC and
decreased in 1.0VDC/hour.
(AEC-Q200-001)
Flame
Retardance
No flame
Condition B No per-heat of samples.
Note: Single Wave Solder - Procedure
2 for SMD and Procedure 1 for
Leaded with solder within 1.5mm of
device body.
Resistance to
Soldering Heat
±ꢄꢀ%+ꢁ.ꢁ5Ωꢅ max.
<50mΩ
* Sulfuration test: H2S 3~5PPM 50 ±2 91%~93%RH 1000H
(MIL-STD-202 Method 210)
Apply to rate current for 0 W
Dimensions in
Dimensions Shown for
reference purposes only.
Specifications subject to
change
9-1773463-7 Rev. G 04/2020
For Email, phone or live chat,
go to: www.te.com/help
millimetres unless
otherwise specified
SMD POWER RESISTORS – AEC-Q200 QUALIFIED
Marking:
Marking for E-96 series in 2512 size: 4 digit marking
First three digits are significant figures of resistance and the fourth
digit represents the number of following zeros. N.B. For values below
100Ω the letter R denotes decimal point eg. 1R80 = 1.8Ω
Marking for E-24 series in 2512 size: 3 digit marking
First two digits are significant figures, and the third digit represents
the number of zeros
Packing specification:
Taping dimensions (mm)
A
B
C
ØD
+0.1 -0 ±0.10 ±0.15 ±0.1
1.5 1.75 5.5 4.0
E
F
G
W
±0.30
12
ØD₁
±0.1
1.5
T
±0.1
1.35
±0.10 ±0.10
3.5 6.7
±0.15
2.0
Peeling strength of Top Cover Tape
Test Condition 0.1 to 0.7 N at a peel-off speed of 300mm / min.
Dimensions in
Dimensions Shown for
reference purposes only.
Specifications subject to
change
9-1773463-7 Rev. G 04/2020
For Email, phone or live chat,
go to: www.te.com/help
millimetres unless
otherwise specified
SMD POWER RESISTORS – AEC-Q200 QUALIFIED
Reel dimension (mm)
Qty / Reel
2000
A ±0.5
2
B ±0.5
13
C ±0.5
21
D ±1
60
M ±2
178
W ±1
13.5
Environment Related Substance
This product complies to EU RoHS directive, EU PAHs directive, EU PFOS
directive and Halogen free.
Ozone layer depleting substances.
Ozone depleting substances are not used in our manufacturing process of this
product.
This product is not manufactured using Chlorofluorocarbons (CFCs),
Hydrochlorofluorocarbons (HCFCs), Hydrobromofluorocarbons (HBFCs) or
other ozone depleting substances in any phase of the manufacturing process.
Storage Condition
The performance of these products, including the solderability, is guaranteed
for a year from the date of arrival at your company, provided that they
remain packed as they were when delivered and stored at a temperature of
25°C ± 10°C and a relative humidity of 60%RH ± 10%RH, chemical and dust
free atmosphere
Even within the above guarantee periods, do not store these products in the
following conditions, otherwise, their electrical performance and/or
solderability may be deteriorated, and the packaging materials (e.g. taping
materials) may be deformed or deteriorated, resulting in mounting failures.
1. In salty air or in air with a high concentration of corrosive gas, such as Cl2,
H2S, NH3, SO2, or NO2
2. In direct sunlight
Dimensions in
Dimensions Shown for
reference purposes only.
Specifications subject to
change
9-1773463-7 Rev. G 04/2020
For Email, phone or live chat,
go to: www.te.com/help
millimetres unless
otherwise specified
SMD POWER RESISTORS – AEC-Q200 QUALIFIED
Recommended solder pad
A
B
C
3.70
3.30
2.70
4 layers PCB specification:
1) Outside 2 layers (Top and Bottom) with copper foil thickness at 2oz.
2) Inside 2 layers (Middle layers) with copper foil thickness at 4 oz.
AEC-Q200
The 3522 series is qualified to AEC-Q200 standard at Grade"4"
How To Order
3522
1K0
Resistance Value
1 ohm 1R0
F
T
Common Part
Tolerance Pack Style
1K ohm 1000 ohms
1K0
3522
F – 1%
J – 5%
T – 2000
reel
1 Meg ohm
1000000 ohms
1M0
Dimensions in
Dimensions Shown for
9-1773463-7 Rev. G 04/2020
For Email, phone or live chat,
go to: www.te.com/help
millimetres unless
otherwise specified
reference purposes only.
Specifications subject to
change
相关型号:
©2020 ICPDF网 联系我们和版权申明