58529-2 [TE]
PRO--CRIMPER III Hand Crimping Tool;型号: | 58529-2 |
厂家: | TE CONNECTIVITY |
描述: | PRO--CRIMPER III Hand Crimping Tool |
文件: | 总6页 (文件大小:246K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Instruction Sheet
PRO- CRIMPER* III Hand
408-9999
Crimping Tool Assembly 58529-1
with Die Assembly 58529-2
11 AUG 14 Rev D
PROPER USE GUIDELINES
Cumulative Trauma Disorders can resultfrom the prolonged use ofmanually powered hand tools. Hand tools are intended for occasional use and low volume
applications. A wide selection of powered application equipment for extended-use, production operations is available.
Locator Assembly
Stationary Jaw
(Supplied with
Back of Tool
Wire Side)
Die Assembly)
Front of Tool
Pivot Pin
(Locator Side)
Die
PRO-CRIMPER III Hand
Crimping Tool Frame
Assembly
Moving Jaw
354940-1 (408-9930)
Ratchet
Adjustment
Wheel
Stationary
Handle
The PRO-CRIMPER III Hand Crimping Tool is a “Commercial” grade tool
and is designed primarily for field installation, repair, maintenance work, or
prototyping in industrial, commercial, or institutional applications. Product
crimped with this tool will meet the crimp height requirement for hand tools in
the appropriate 114 series specification, but may not comply with other feature
parameters of the specification. TE Connectivity offers a variety of tools to
satisfy your performance requirements. For additional information, contact the
Tooling Assistance Center at 1-800-722-1111.
Moving Handle
Wire
TE Die
Assembly
TE Locator
Assemblya
Contact
Familyc
Size
(AWG)
Strip Length
(mm [In.])
Insul Dia
16
AMPSEAL*
Contacts
1.7 to 2.7
5.15.1 á.4
[.20 á.02]
58529-- 2
58515-- 1
[.07 to .11]
18 to 20
a
c
Supplied with the die assembly. Also available separately.
Call the Tooling Assistance Center or Production Information (see below) for product part numbers.
Figure 1
Dimensions on this sheet are in millimeters [with
inch equivalents provided in brackets]. Figures
and illustrations are for identification only and are
not drawn to scale.
1. INTRODUCTION
NOTE
PRO--CRIMPER III Hand Crimping Tool
Assembly 58529--1 consists of Die Assembly
58529--2 and PRO--CRIMPER III Hand Tool Frame
354940--1. The die assembly consists of crimping
dies and a locator assembly.
i
2. DESCRIPTION (Figures 1 and 2)
Read these instructions thoroughly before crimping
any contacts.
The tool features a tool frame with a stationary jaw
and handle, a moving jaw, a moving handle, and an
adjustable ratchet that ensures full contact crimping.
Reasons for reissue are provided in Section 11,
REVISION SUMMARY.
.2014 TE Connectivity family of companies
All Rights Reserved
TOOLING ASSISTANCE CENTER 1--800--722--1111 This controlled document is subject to change.
1 of 6
PRODUCT INFORMATION 1--800--522--6752
For latest revision and Regional Customer Service,
*Trademark
visit our website at www.te.com
LOC B
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.
408-9999
Locator
Nut
Assembly
Tool Frame
Locator
Insulation
Crimper
Die Retaing
Pins
Chamfer
Wire Crimper
Offset
Wire Anvil
Chamfer
Die Retaining
Screws
Insulation
Anvil
Figure 2
The tool frame holds a die assembly with two
crimping sections.
5. Place the wire crimper and insulation crimper so
that their chamfered sides and their marked
surfaces face outward, when mounted in the
stationary jaw of the tool frame.
The die assembly features a wire anvil, an insulation
anvil, a wire crimper, and an insulation crimper.
6. Insert the two die retaining pins.
Attached to the outside of the frame is a locator
assembly, which contains a locator, a spring retainer,
and a contact support.
7. Insert the long die retaining screw through the
jaw and through both crimper dies, and tighten the
screw just enough to hold the dies in place. Do not
tighten the screw completely at this time.
Die retaining pins and die retaining screws are used
to position and secure the dies in the tool frame. A
nut is used on the upper die retaining screw to hold
the locator assembly in place.
8. Carefully close the tool handles, making sure
that the anvils and crimpers align properly.
9. Continue closing the tool handles until the
ratchet in the tool frame has engaged sufficiently to
hold the anvils and crimpers in place, then tighten
both die retaining screws.
3. INSTALLATION AND REMOVAL OF DIE SET
AND LOCATOR ASSEMBLY (Figure 2)
1. Open the tool handles and remove the two die
retaining screws from the tool jaws.
10. Place the locator assembly over the end of the
long screw, and position the locator assembly
against the side of the tool jaw.
2. Place the wire anvil and insulation anvil so that
their chamfered sides and their marked surfaces
face outward, when mounted in the moving jaw of
the tool frame.
11. Place the nut onto the end of the long screw
and tighten the nut enough to hold the locator
assembly in place, while still allowing the locator to
slide up and down.
3. Insert the two die retaining pins.
12. To disassemble, close the tool handles until the
ratchet releases, remove the nut, the locator
assembly, the two die retaining screws, and the
four die retaining pins, and slide the anvils and
crimpers out of the tool jaws.
4. Insert the short die retaining screw through the
jaw and through both anvil dies, and tighten the
screw just enough to hold the dies in place. Do not
tighten the screw completely at this time.
2 of 6
Rev D
408-9999
contact is still being bent during crimping, repeat
4. CONTACT SUPPORT ADJUSTMENT (Figure 3)
the adjustment procedure.
The contact support is preset prior to shipment,
but minor adjustment may be necessary.
NOTE
5. CRIMPING PROCEDURE
i
This tool is provided with a crimp adjustment
NOTE
feature. Initially, the crimp height should be
verified as specified in Figure 4. Refer to
Section 6, CRIMP HEIGHT INSPECTION, and
Section 7, RATCHET ADJUSTMENT, to verify
crimp height before using the tool to crimp
desired contacts and wire sizes.
1. Make a sample crimp and determine if the
contact is straight, bending upward, or bending
downward.
i
2. If adjustment is required, loosen the screw that
holds the contact support onto the locator
assembly.
Refer to the table in Figure 1 and select wire of the
specified size and insulation diameter. Strip the wire
to the length indicated in Figure 1, taking care not to
nick or cut wire strands. Select an applicable contact
and identify the appropriate crimp section according
to the wire size markings on the tool. Refer to
Figure 3 and proceed as follows:
The ratchet has detents that create audible clicks
as the tool handles are closed.
NOTE
i
3. Place a contact with wire into the proper nest
and close the tool handles until the ratchet reaches
the sixth click, or until the contact support touches
the contact.
1. Hold the tool so that the back (wire side) is
facing you. Squeeze tool handles together and
allow them to open fully.
4. Slightly loosen the nut that holds the locator
assembly onto the tool frame.
2. Holding the contact by the mating end, insert the
contact — insulation barrel first — through the front
of the tool and into the appropriate crimp section.
5. Move the contact support as required to
eliminate the bending of the contact.
3. Position the contact so that the mating end of
the contact is on the locator side of the tool, and so
that the open “U” of the wire and insulation barrels
face the top of the tool. Place the contact up into
the nest so that the movable locator drops into the
slot in the contact. Refer to Figure 3. Butt the front
end of the wire barrel against the movable locator.
6. Tighten the nut and close the handles until the
ratchet releases.
7. Remove and inspect the contact.
8. Make another sample crimp. If the contact is
straight, tighten the contact support screw. If the
Contact
Locator
Support
Back of Tool
(Wire Side)
Adjustment
Screw for
Contact
Support
Strip
Contact
(Typ)
Length
Locator
in Wire
Slot
Wire
Wire
Inserted
to Stop
Figure 3
Rev D
3 of 6
408-9999
Make sure that both sides of the insulation barrel
are started evenly into the crimping section. Do
NOT attempt to crimp an improperly positioned
contact.
Proceed as follows:
CAUTION
1. Refer to Figure 4 and select a wire (maximum
size) for each crimp section listed.
!
2. Refer to Section 5, CRIMPING PROCEDURE,
and crimp the contact(s) accordingly.
4. Hold the contact in position and squeeze the
tool handles together until ratchet engages
sufficiently to hold the contact in position. Do NOT
deform insulation barrel or wire barrel.
3. Using a crimp height comparator, measure the
wire barrel crimp height as shown in Figure 4. If the
crimp height conforms to that shown in the table,
the tool is considered dimensionally correct. If not,
the tool must be adjusted. Refer to Section 7,
RATCHET ADJUSTMENT.
5. Insert stripped wire into contact insulation and
wire barrels until it is butted against the wire stop,
as shown in Figure 3.
6. Holding the wire in place, squeeze tool handles
together until ratchet releases. Allow tool handles
to open and remove crimped contact.
7. RATCHET (Crimp Height) ADJUSTMENT (Figure 5)
1. Remove the lockscrew from the ratchet
adjustment wheel.
The crimped contact may stick in the crimping
area, but the contact can be easily removed by
pushing downward on the top of the locator (see
Figure 3).
NOTE
2. With a screwdriver, adjust the ratchet wheel
from the locator side of the tool.
i
3. Observe the ratchet adjustment wheel. If a
tighter crimp is required, rotate the adjustment
wheel COUNTERCLOCKWISE to a
7. Check the contact’s crimp height as described in
Section 6, CRIMP HEIGHT INSPECTION. If
necessary, adjust the crimp height as described in
Section 7, RATCHET ADJUSTMENT.
higher--numbered setting. If a looser crimp is
required, rotate the adjustment wheel
CLOCKWISE to a lower--numbered setting.
4. Replace the lockscrew.
6. CRIMP HEIGHT INSPECTION
5. Make a sample crimp and measure the crimp
height. If the dimension is acceptable, replace and
secure the lockscrew. If the dimension is
unacceptable, continue to adjust the ratchet, and
again measure a sample crimp.
Crimp height inspection is performed through the use
of a micrometer with a modified anvil, commonly
referred to as a crimp--height comparator. TE does
not manufacture or market crimp--height comparators.
Detailed information on obtaining and using
crimp--height comparators can be found in instruction
sheet 408--7424.
Screwdriver
Position Point
on Center of
Wire Barrel
Opposite
Seam
Modified Anvil
“A”
Ratchet
Adjustment
Wheel
Wire Size
AWG (Max)
Crimp Section
(Wire Size Marking)
Crimp Height
Dimension A
1.22á.05
18
16
20--18
[.048á.002]
1.41á.05
Lockscrew
(Typ)
16
[.056á.002]
Figure 4
Figure 5
4 of 6
Rev D
408-9999
Available separately, PRO--CRIMPER III Hand
8. MAINTENANCE
Crimping Tool Repair Kit 679221--1 includes a
replacement nut and a variety of pins, rings, screws,
and springs.
Ensure that the tool and dies are clean by wiping
them with a clean, soft cloth. Remove any debris with
a clean, soft brush. Do not use objects that could
damage the tool. When not in use, keep handles
closed to prevent objects from becoming lodged in
the crimping dies, and store in a clean, dry area.
If the dies are damaged or worn excessively, they
must be replaced.
Order the repair kit and replaceable parts through
your TE representative, or call 1--800--526--5142, or
send a facsimile of your purchase order to
1--717--986--7605, or write to:
9. VISUAL INSPECTION
The crimping dies should be inspected on a regular
basis to ensure that they have not become worn or
damaged. Inspect the crimp sections for flattened,
chipped, worn, or broken areas. If damage or
abnormal wear is evident, the tool must be replaced.
See Section 10, REPLACEMENT.
CUSTOMER SERVICE (38--35)
TYCO ELECTRONICS
PO BOX 3608
HARRISBURG PA 17105--3608
11.REVISION SUMMARY
10. REPLACEMENT
Revisions to this instruction sheet include:
: Changed wire size in table in Figure 1
Customer--replaceable parts are shown in Figure 1.
Rev D
5 of 6
408-9999
Die Assembly 58529-2 Can Be Used In the Following Tools:
PRO-CRIMPER III Hand Tool 354940-1
SDE PEW-12 Hand Tool 9-1478240-0
(Instruction Sheet 408-8851)
(Instruction Sheet 408-9930)
SDE Bench Terminator 1490076-2
(Customer Manual 409-10052)
626 Adapter 679304-1
(Instruction Sheet 408-4070)
Battery Tool (Pin Die) 1213890-1, -2
(Customer Manual 409-10065)
Battery Tool (Shouldered Die) 1725837-1, -2
(Customer Manual 409-10053)
6 of 6
Rev D
相关型号:
5852BK001
Wire And Cable, 7 Conductor(s), 28AWG, 600V, Flexible Cord And Fixture Wire, ROHS AND REACH COMPLIANT
ALPHAWIRE
58537-302LF
Board Connector, 24 Contact(s), 4 Row(s), Male, Straight, Press Fit Terminal, LEAD FREE
AMPHENOL
58537-306LF
Board Connector, 24 Contact(s), 4 Row(s), Male, Straight, Press Fit Terminal, LEAD FREE
AMPHENOL
©2020 ICPDF网 联系我们和版权申明