AT-263 [TE]

Digital Attenuator, 31 dB, 5-Bit, TTL Driver, DC - 2 GHz; 数字衰减31分贝, 5位, TTL驱动器, DC - 2 GHz的
AT-263
型号: AT-263
厂家: TE CONNECTIVITY    TE CONNECTIVITY
描述:

Digital Attenuator, 31 dB, 5-Bit, TTL Driver, DC - 2 GHz
数字衰减31分贝, 5位, TTL驱动器, DC - 2 GHz的

驱动器
文件: 总3页 (文件大小:229K)
中文:  中文翻译
下载:  下载PDF数据表文档文件
Digital Attenuator, 31 dB, 5-Bit,  
TTL Driver, DC - 2 GHz  
V 3.00  
Features  
CR-12  
n
Attenuation: 1 dB steps to 31 dB  
n
Temperature Stability: ± 0.18 dB from –55°C to +85°C  
Typical  
n
n
n
n
Low DC Power Consumption  
Hermetic Surface Mount Package  
Integral TTL Driver  
50 Ohm Nominal Impedance  
Description  
M/A-COM’s AT-263 is  
a GaAs FET 5-bit digital  
attenuator with a 1 dB minimum step size and 31 dB total  
attenuation. This attenuator and integral TTL driver is in a  
hermetically sealed ceramic 16-lead surface mount package.  
The AT-263 is ideally suited for use where accuracy, fast  
switching, very low power consumption and low  
intermodulation products are required. Typical applications  
include dynamic range setting in precision receiver circuits  
and other gain/leveling control circuits. Environmental  
screening is available. Contact the factory for information.  
Electrical Specifications1  
(From –55°C to +85°C)  
Parameter  
Test Conditions  
Frequency  
Units  
Min  
Typ  
Max  
Reference Insertion Loss  
DC - 0.5 GHz  
DC - 1.0 GHz  
DC - 2.0 GHz  
dB  
dB  
dB  
2.4  
2.8  
3.0  
Attenuation Accuracy 2  
Any Single Bit  
Any Combination of Bits  
DC - 1.0 GHz  
DC - 2.0 GHz  
± (0.25 +3% of atten setting in dB) dB  
± (0.25 +3% of atten setting in dB) dB  
or ± 0.4 dB, whichever is greater  
VSWR  
Trise, Tfall  
DC - 2.0 GHz  
Ratio  
ns  
9
1.6:1  
10% to 90%  
Ton, Toff  
50% Control to 90/10% RF  
In-Band (peak-peak)  
ns  
40  
30  
Transients  
mV  
1 dB Compression  
Input Power  
Input Power  
0.05 GHz  
0.5 - 2.0 GHz  
dBm  
dBm  
+20  
+28  
Input IP3  
Input IP2  
For two-tone Input Power  
Up to +5 dBm  
0.05 GHz  
0.5 - 2.0 GHz  
dBm  
dBm  
+40  
+48  
For two-tone Input Power  
Up to +5 dBm  
0.05 GHz  
0.5 - 2.0 GHz  
dBm  
dBm  
+45  
+68  
Vcc  
Vee  
V
V
4.5  
5.0  
5.5  
-8.0  
-5.0  
1. All specifications apply when operated with bias voltages of +5V for Vcc and –5.0V for Vee.  
2. This attenuator is guaranteed monotonic.  
Digital Attenuator, 31 dB, 5-Bit, TTL Driver, DC - 2 GHz  
Electrical Specifications (From –55°C to +85°C)  
AT-263  
V 3.00  
Parameter  
Test Conditions  
Frequency  
Units  
Min  
Typ  
Max  
Icc  
Vcc = 4.5 to 5.5V  
mA  
5.0  
Vctl = 0 to 0.8V, or Vcc –2.1V to Vcc  
Iee  
Vee = -5.0 to -8.0V  
mA  
1.0  
Vctl  
Vctl  
Logic 0 (TTL)  
Logic 1 (TTL)  
V
V
0.0  
2.0  
0.8  
5.0  
Input Leakage Current (Low)  
Input Leakage Current (High)  
0 to 0.8V  
µA  
µA  
1.0  
1.0  
2.0 to 5.0V  
Absolute Maximum Ratings 3  
Truth Table  
Control Inputs  
Parameter  
Absolute Maximum  
Max Input Power  
0.5 GHz  
0.5 - 2.0 GHz  
C5  
0
C4  
0
C3  
0
C2  
0
C1  
0
Attenuation  
Reference  
1 dB  
+27 dBm  
+34 dBm  
0
0
0
0
1
Supply Voltages  
Vcc  
Vee  
+5.5V  
-8.5V  
0
0
0
1
0
2 dB  
Control Voltage 4  
Operating Temperature  
Storage Temperature  
-0.5V to Vcc +0.5V  
-55°C to +125°C  
-65°C to +150°C  
0
0
1
0
0
4 dB  
0
1
0
0
0
8 dB  
1
0
0
0
0
16 dB  
1
1
1
1
1
31 dB  
3. Operation of this device above any one of these parameters  
may cause permanent damage.  
4. Standard CMOS TTL interface, latch-up will occur if logic  
signal is applied prior to power supply.  
0 = TTL Low  
1 = TTL High  
Functional Schematic (Top View)  
C5  
+5V  
-5V  
C4  
RF2  
16 dB  
8 dB  
GND  
GND  
GND  
4 dB  
2 dB  
1 dB  
C3  
GND  
GND  
C2  
C1  
GND Orientation Mark  
RF1 PIN 1  
PIN 16 GND  
2
Specifications subject to change without notice.  
n North America: Tel. (800) 366-2266  
n Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298  
n Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020  
Visit www.macom.com for additional data sheets and product information.  
Digital Attenuator, 31 dB, 5-Bit, TTL Driver, DC - 2 GHz  
Typical Performance Curves  
AT-263  
V 3.00  
Ref. Insertion Loss vs. Frequency  
Attenuation Accuracy vs. Frequency  
+85°C  
+25°C  
-55°C  
1,2,4,8,16 dB  
Full Attenuation  
0.5  
0
5
4
3
2
1
0
-0.5  
-1  
-1.5  
0.0  
0.5  
1.0  
1.5  
2.0  
0.0  
0.5  
1.0  
Frequency (GHz)  
1.5  
2.0  
Frequency (GHz)  
VSWR vs. Frequency  
Ordering Information  
4 dB State  
1 dB State  
Part Number  
Package  
2.00  
1.80  
1.60  
1.40  
1.20  
1.00  
AT-263 PIN  
CR-12  
0.00  
0.50  
1.00  
1.50  
2.00  
Frequency (GHz)  
3
Specifications subject to change without notice.  
n North America: Tel. (800) 366-2266  
n Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298  
n Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020  
Visit www.macom.com for additional data sheets and product information.  

相关型号:

AT-263-PIN

Digital Attenuator 31.0dB, TTL Driver, DC-2.0 GHz
TE

AT-263-TB

Digital Attenuator 31.0dB, TTL Driver, DC-2.0 GHz
TE

AT-263PIN

Digital Attenuator, 31 dB, 5-Bit, TTL Driver, DC - 2 GHz
TE

AT-263TR

Digital Attenuator 31.0dB, TTL Driver, DC-2.0 GHz
TE

AT-264

Digital Attenuator, 4 Bit, Single Control 30 dB, 0.5 - 2.0 GHz
TE

AT-264-PIN

Digital Attenuator, 4-Bit, Single Control 30 dB, 0.5 - 2.0 GHz
TE

AT-264PIN

Digital Attenuator, 4 Bit, Single Control, 30 dB, 0.5-2.0 GHz
TE

AT-264TR

Digital Attenuator, 4 Bit, Single Control 30 dB, 0.5 - 2.0 GHz
TE

AT-264_1

Digital Attenuator, 4-Bit, Single Control 30dB, 0.5-2.0 GHz
TE

AT-266

Digital Attenuator, 1 Bit, 10 dB Step DC - 2.0 GHz
TE

AT-266RTR

Digital Attenuator, 1 Bit, 10 dB Step DC - 2.0 GHz
TE

AT-266TR

Digital Attenuator, 1 Bit, 10 dB Step DC - 2.0 GHz
TE