DS11-1Y [TE]
DC solid state relay for loads up to 2A @ 60Vdc; 直流固态继电器的负载可达2A, 60V直流型号: | DS11-1Y |
厂家: | TE CONNECTIVITY |
描述: | DC solid state relay for loads up to 2A @ 60Vdc |
文件: | 总4页 (文件大小:124K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
DS11 Series High Performance Solid State Relays
DC solid state relay for loads up to 2A @ 60Vdc
Product Facts
ꢀ Standard options: short
circuit/overload protection,
switch status and trip
status.
ꢀ Optically coupled all solid
state relay.
ꢀ TTL & CMOS compatible
input.
DS11 series SSRs feature
state of the art photo-voltaic switch status or trip status.
and wiring; and isolated
the output is off and a logic
“1” when the output is on.
Trip status, also optically
isolated from the load,
provides a logic “1” if the
output trips off and a logic
“0” when the output is in a
normal condition, on or off,
and is available only in
conjunction with short
ꢀ Low on-resistance power
MOSFET output.
ꢀ Tested per MIL-R-28750 and
approved to DSCC drawing
88062 with “Y” level
screening.
optical isolation and power
MOSFET output chips for
ultra-reliable high speed
switching of DC loads up to
2 amps, with extremely low
on-resistance. Standard
options include integral
current overload/short
circuit protection to provide
protection of the relay, load
The overload feature
provides protection if a
short or overload develops
while the relay is in the on
state or if the relay is turned
on into a dead short. Switch
status, optically isolated
from the load, signals the
status of the output and
provides a logic “0” when
circuit protection.
CII Part No. DSCC Dwg. No.
Relay Version
DS11-1Y
DS11-1000
DS11-1001
DS11-1002
DS11-1003
88062-008
88062-004
88062-006
88062-002
N/A
Basic relay
Relay w/ short circuit protection
Relay w/ switch status
Relay w/ short circuit protection and switch status
Relay w/ short circuit protection and trip status
2 Terminal Input Configuration
Direct Drive (Status Optional)
Status Output
Load
TTL Drive
Load
V
Status
V
+V Supply
CC
+V Load Supply
V
CC
1
14
3
6
OUTPUT
INPUT
6
3
1
8
12
INPUT
OUTPUT
14
8
12
TTL
3 Terminal Input Configuration
With Output Status
Without Output Status
Load
V
Status Output
Status
V
+V Supply
CC
Load
V
+V Load Supply
CC
1
3
6
OUTPUT
INPUT
14
8
12
1
3
6
INPUT
OUTPUT
14
8
12
TTL or CMOS
TTL or CMOS
© 2004 by Tyco Electronics Corporation. All Rights Reserved.
CII and TYCO are trademarks.
1
Catalog DS11-TBD
Issued 1-04
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
www.tycoelectronics.com
C. America: 52-55-5-729-0425
UK: 44-141-810-8967
DS11 Series High Performance Solid State Relays
DC solid state relay for loads up to 2A @ 60Vdc (Continued)
Environmental Characteristics
Electrical Specifications (-55°C to +105°C unless otherwise specified)
Ambient Temperature Range:
Operating: -55°C to +105°C.
Storage: -55°C to +105°C.
Input (2 terminal configuration)
Input supply voltage range (Vcc)
Input current (max.) @ 5Vdc
Must turn-on voltage
3.8 - 32 Vdc (Notes 1 & 2, Figures 1 & 2)
15mAdc (Notes 1 & 2, Figures 1 & 2)
Vibration Resistance:
100 G’s, 10-3,000 Hz.
3.8Vdc
1.5Vdc
-32Vdc
Must turn-off voltage
Shock Resistance:
50 G’s, 11 ms pulse.
Reverse voltage protection
Input (3 terminal configuration)
Control voltage range
Constant Acceleration Resistance
(Y1 axis):
5,000 G’s.
0 - 18 Vd
250µAdc @ 5V, 1mA @ 18V
3.8 - 32 Vdc (Notes 1 & 2, Figures 1 & 2)
15mADC (Notes 1 & 2, Figures 1 & 2)
0.3Vdc
Control current (max.)
Input supply voltage range (Vcc)
Input current (max.) @ 5Vdc
Must turn-on voltage
Mechanical Characteristics
Must turn-off voltage
3.2Vdc
Weight (approx.):
.176 oz. (5 grams)
I/O
Materials:
Header: Kovar
Cover: Nickel
Dielectric strength (min.)
Insulation resistance (min.) @ 500Vdc
Capacitance (max.)
1,000V rms
9
10 ohms
10pF
Pins: Kovar, gold plated
Output
Continuous load current (max.) @ 25°C
Continuous load voltage (max.)
Transient blocking voltage (max.)
On resistance (max.) @ T = 25°C, I = 100mA
2.1Adc (Figure 7)
60Vdc
80Vdc (Note 5)
0.15 ohm (Note 6, Figure 6)
0.5Vdc
j
L
Output voltage drop (max.)
Leakage current (max.) @ V = 60Vdc
Leakage current (max.) @ V = 60Vdc, with switch status
Turn-on time (max.)
100µAdc
2mAdc
3 ms (Figure 3)
1 ms (Figure 3)
100V / µs
Turn-off time (max.)
dv/dt (min.)
Electrical system spike
600Vdc (Note 5)
125°C
Output chip junction temperature (max.)
Thermal resistance (max.), junction to ambient
Thermal resistance (max.), junction to case
Status
90°C/W
25°C/W
Status supply voltage range
1 - 18Vdc
600µADC (Figure 5, Note 8)
10µAdc
Status current (max.) @ Vstatus ≤ 0.4Vdc
Status leakage current (max.) @ 16Vdc
Status turn-on time (max.)
3.5 ms (Figure 4)
8 ms (Figure 4)
Status turn-off time (max.)
Short Circuit Protection
Current surge without tripping (max.), 100ms pulse
Overload trip current (max.), 0.5 ms pulse, V = 60Vdc
Trip time (typical), turning on into short
Trip time (typical), shorting while relay is on
4.25Adc
10Adc
400µs
280µs
2
Catalog DS11-TBD
Issued 1-04
Dimensions are in inches and
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
www.tycoelectronics.com
C. America: 52-55-5-729-0425
UK: 44-141-810-8967
DS11 Series High Performance Solid State Relays
DC solid state relay for loads up to 2A @ 60Vdc (Continued)
Figure 1 - Maximum Input Current vs. Input Voltage
Figure 2 - Series Resistance vs. Vcc Supply Voltage (Note 1)
18
15
1800
1500
1200
900
12
9
6
600
3
300
0
0
0
5
10 15
30
20 25 40 50 60
0
6
10 15
20 25 30 35
Input Voltage, Vcc (Vdc)
Vcc (Volts)
Figure 3 - Turn-on and Turn-off Timing
Figure 4 - Output Status Timing
OFF
Pin 14
(Input)
V
High
Low
Off
Control
50%
ON
T
V
S
Pin 6-8
90%
10%
90%
10%
On
T
Status
Turn-On
Time
T
T
Status
Turn-Off
Time
On
Off
Figure 5 - Status Resistor vs. Status Supply Voltage
Figure 6 - On-Resistance vs. Temperature (Note 6)
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
35000
30000
25000
20000
15000
10000
0.4
0.2
0.0
5000
0
0
5
10
15
20
25
50
75
100
125
Junction Temperature (°C)
Status Supply Voltage (Volts)
3
Catalog DS11-TBD
Issued 1-04
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
www.tycoelectronics.com
UK: 44-141-810-8967
DS11 Series High Performance Solid State Relays
DC solid state relay for loads up to 2A @ 60Vdc (Continued)
Figure 7 - Temperature Derating Curve
Figure 8 - Maximum Surge Current Without Tripping
2.0
1.8
1.6
1.4
7.0
-55°C
6.0
5.0
1.2
1.0
0.8
0.6
0.4
0.2
0
+25°C
4.0
3.0
+85°C
2.0
1.0
0.01
0.1
1
10
-50 -40 -20
0
20 40 60 80 100 120
Time (seconds)
Ambient Temperature (°C)
Figure 9 - Outline Dimensions
.273 .020
(6.93 .50)
.530 MAX
(13.46)
.490 REF.
(12.44)
.140
(3.55)
.200
(5.08)
.020 MAX.
(.50)
TOP MARKING
ORIENT AS
SHOWN
.890 MAX.
(22.60)
.500
(12.70)
.850 REF.
(21.59)
.600
(15.24)
.190 MAX.
(4.82)
.110
DATE CODE
HERE
(2.79)
.017 +.002, –.001 DIA.
(.43 + .05, –.02)
6 PLS.
.300
(7.62)
TOLERANCE:
0.010 (0.25mm) FOR 2 PLACE DECIMALS,
0.005 (0.13mm) FOR 3 PLACE DECIMALS.
UNLESS OTHERWISE SPECIFIED
Notes
1.2 terminal input configuration is compatible with CMOS or open collector TTL (with pull-up resistor). For Vcc levels above 6Vdc, a series limiting resistor is
required. See Fig. 2 for resistor value. Use standard resistor value equal to or less than value from the curve.
2.Input transitions to be ≤ 1ms duration, and input direct drive should be “bounceless contact” type.
3. Vcc = 5Vdc for all tests unless otherwise specified.
4.All DS11 Series relays may drive loads connected to either positive or negative referenced power supply lines. Reversing polarity of output may cause permanent
damage. Inductive loads must be diode suppressed.
5.Transient blocking voltage and electrical system spike tests are performed per MIL-STD-704 (28VDC systems).
6.To determine the maximum on-resistance at any given junction temperature, multiply on-resistance at 25°C (0.15 ohm) by normalized on-resistance factor from
curve (Fig. 6).
7.Overload testing per MIL-R-28750 is constrained to the limits imposed by the short circuit protection requirements of this specification and DSCC drawing 88062.
Load circuit series inductance for “load shorted” mode of operation to be limited to 50mH max. Maximum repetition rate into a shorted load should not exceed 10
Hz.
8.Proper operation of the status feedback requires a status pull-up resistor. See Fig. 5 for status resistor value.
DS11-TBD–PDF–KRG–1-04
4
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
www.tycoelectronics.com
UK: 44-141-810-8967
相关型号:
©2020 ICPDF网 联系我们和版权申明