MA4L_1 [TE]
Silicon PIN Limiter Diodes; 硅PIN二极管限
| 型号： | MA4L_1 |
| 厂家： | 
TE CONNECTIVITY |
| 描述： | Silicon PIN Limiter Diodes |
| 文件： | 总6页 (文件大小：376K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Silicon PIN Limiter Diodes
MA4L Series
V 5.0
5
Absolute Maximum Ratings1
@ T = +25°C ( Unless otherwise specified )
Features
A
• Lower Insertion Loss and Noise Figure
• Higher Peak and Average Operating Power
• Various P1dB Compression Powers
• Lower Flat Leakage Power
Parameter
Forward Current
Absolute Maximum
100 mA
Operating Temperature
Storage Temperature
Junction Temperature
RF Peak Incident Power
RF C.W. Incident Power
Mounting Temperature
Notes:
-55°C to +125°C
-55°C to +150°C
+175°C
• Reliable Silicon Nitride Passivation
Per Performance Table
Per Performance Table
+320°C for 10 sec.
Description
M/A-COM produces a series of small and
medium I-region length silicon PIN diodes
specifically designed for high signal limiter
applications. Each of these devices provides
circuit designers with lower insertion loss at
zero bias, faster response and recovery times,
and lower flat leakage power. This series of
diode is available as passivated chips
(ODS 132 or ODS 134) as well as hermetic
surface mount and cylindrical ceramic
packages. Consult factory for specific package
style availability.
1. Exceeding these limits may cause permanent damage.
A Square
Anode
Applications
The MA4L Series of PIN limiter diodes are
designed for use in passive limiter control
circuits to protect sensitive receiver components
such as low noise amplifiers ( LNA ), detectors,
and mixers covering the 10MHz to 18GHz
frequency band.
.007” +/- .001
(0.18 mm +/- .02)
ODS
Dimension
Mils
mm
0.33 +/- 0.05
0.51 +/- 0.05
134
132
A
A
13 +/- 2.0
20 +/- 2.0
Specification Subject to Change Without Notice
1
M/A-COM Inc.
þ
43 South Avenue, Burlington, MA 01803 USA
þ
Telephone: 781-564-3100
Silicon PIN Limiter Diodes
MA4L Series
V 5.0
Un-Packaged Die Electrical Specifications at +25°C
Nominal Characteristics
Carrier
Lifetime
@
10mA
nS
15
15
15
20
20
15
90
800
Minimum Maximum
Part Number
Maximum1
RS 10mA
Ohms
2.00
Thermal2
Thickness Diameter Resistance
Reverse
Voltage
VR
Reverse
Voltage
VR
Minimum Maximum
I-Region
Contact
Cj0V
pF
Cj0V
pF
µM
2
mils
1.00
1.00
1.00
1.50
1.50
1.50
3.50
4.50
°C/W
200
200
200
150
150
150
30
MA4L011-134
MA4L021-134
MA4L022-134
MA4L031-134
MA4L032-134
MA4L062-134
MA4L101-134
MA4L401-132
20
35
0.13
0.13
0.13
0.13
0.13
0.07
0.20
0.20
0.20
0.20
0.20
0.15
0.15
0.30
20
35
2.00
2.00
2.50
2.50
2.50
2.00
1.20
2
2
3
3
20
35
30
50
30
50
65
75
4
100
250
13
25
25
Nominal High Signal Performance @ +25º C
Incident3
Incident3
Incident3
Recovery3
Time, (3dB)
@ 50W Peak
Power
Maximum3
Incident Peak
Power
Maximum4
CW Input
Power
Peak Power Peak Power Peak Power
For 1dB
Limiting @
9.4GHz
dBm
For 10dB
Limiting @
9.4GHz
dBm
For 20dB
Limiting @
9.4GHz
dBm
Part Number
nS
10
10
10
20
20
20
10
Watts
100
Watts
MA4L011-134
MA4L021-134
MA4L022-134
MA4L031-134
MA4L032-134
MA4L062-134
MA4L101-134
MA4L401-132
7
25
40
2
4
3
5
3
5
4
10
10
16
16
16
19
29
30
30
36
36
36
42
52
43
43
49
49
49
52
65
400
200
800
600
600
900
100
2000
10
Specification Subject to Change Without Notice
M/A-COM Inc. 43 South Avenue, Burlington, MA 01803 USA
2
þ
þ
Telephone: 781-564-3100
Silicon PIN Limiter Diodes
MA4L Series
V 5.0
Notes for Specifications and Nominal High Signal Performance Table:
1. Maximum Series Resistance - RS, is measured at 500MHz in the ODS-30 package and is equivalent
to the total diode resistance : Rs = Rj ( Junction Resistance) + Rc ( Ohmic Resistance)
2. Nominal C.W. Thermal Resistance - θTH is measured in ceramic pill package, ODS-30, mounted to
a metal ( infinite ) heatsink. Diode only thermal resistance values are approximately 2 ºC/W lower in
value than the ODS-30 listed package values.
3. Maximum High Signal Performance – Measured using a single shunt diode ( die ) attached
directly to the gold plated RF housing ground with 2 mil thick conductive silver epoxy in a 50Ω,
SMA, connectorized test fixture. Chip anode contact is thermo sonically wire bonded using a
1 mil dia. gold wire onto a 7.2 mil thick Rogers 5880 duroid microstrip trace. A shunt coil
provides the D.C. return. Test Frequency = 9.4 GHz, RF pulse width = 1.0 µS, 0.001 duty cycle.
4. Maximum C.W Incident Power - Measured in a 50 Ω, SMA, connectorized housing @ 4GHz utilizing a
TWT amplifier and the same single diode assembly configuration as stated in Note 3 above.
Die Handling and Mounting Information
Handling: All semiconductor chips should be handled with care in order to avoid damage or contamination
from perspiration, salts, and skin oils. For individual die, the use of plastic tipped tweezers or vacuum pick
up tools is strongly recommended. Bulk handling should ensure that abrasion and mechanical shock are
minimized.
Die Attach: The die have Ti-Pt-Au back and anode metal, with a final gold thickness of 1.0 µm. Die can be
mounted with a gold-tin, eutectic solder preform or conductive silver epoxy. The metal RF and D.C. ground
plane mounting surface must be free of contamination and should have a surface flatness of < +/- 0.002“.
Eutectic Die Attachment Using Hot Gas Die Bounder: An 80/20, gold-tin eutectic solder preform is
recommended with a work surface temperature of 255oC and a tool tip temperature of 220oC. When the hot
gas is applied, the temperature at the tool tip should be approximately 290oC. The chip should not be
exposed to temperatures greater than 320oC for more than 10 seconds.
Eutectic Die Attachment Using Reflow Oven: See Application Note M541, “Bonding and Handling
Procedures for Chip Diode Devices” at www.macom.com. for recommended profile.
Epoxy Die Attachment: A thin, controlled amount of electrically conductive silver epoxy should be applied
at approximately a 1–2 mils thickness to minimize ohmic and thermal resistances. A thin epoxy fillet should
be visible around the perimeter of the chip after placement to ensure full area coverage. Cure conductive
epoxy per manufacturer’s schedule.
Die Bonding: The anode bond pads on these die have a Ti-Pt-Au metallization scheme, with a final gold
thickness of 1.0 µm. Thermosonic wedge wire bonding of 0.001” diameter gold wire is recommended with a
stage temperature of 150oC and a force of 18 to 40 grams. Ultrasonic energy should be adjusted to the
minimum required. Automatic ball bonding can also be used.
See Application Note M541, “Bonding and Handling Procedures for Chip Diode Devices”
for more detailed handling and assembly instructions at www.macom.com.
Specification Subject to Change Without Notice
3
M/A-COM Inc.
þ
43 South Avenue, Burlington, MA 01803 USA
þ
Telephone: 781-564-3100
Silicon PIN Limiter Diodes
MA4L Series
V 5.0
Typical High Signal Peak Power Performance for the Single Shunt Limiter Diode
in a 50Ω Test Fixture ( Note 3 )
Typical Peak Power Performance for Single Shunt Limiter Diode in 50 Ohm System
at 9.4 GHz, 1uS Pulse Width, 0.001 Duty
45
40
35
30
25
20
15
10
5
MA4L022-134
MA4L032-134
MA4L101-134
MA4L401-132
0 dB Loss
Line
30 dB Loss
Line
10 dB Loss
Line
20 dB Loss
Line
0
0
10
20
30
40
50
Pin ( dBm )
Specification Subject to Change Without Notice
M/A-COM Inc. 43 South Avenue, Burlington, MA 01803 USA
4
þ
þ
Telephone: 781-564-3100
Silicon PIN Limiter Diodes
MA4L Series
V 5.0
Application Circuits
Typical +60dBm Peak Power, 1µS P.W., 0.001% Duty Cycle, +20dBm Flat Leakage Limiter Circuit
Transmission Line: 90º @ Fo
Transmission Line: 90º @ Fo
RF Input
RF Output
MA4L032-134
MA4L401-132
Coil: D.C. Return
MA4L101-134
Typical +50 dBm Peak Power, 1µS P.W., 0.001% Duty Cycle, +20 dBm Flat Leakage Limiter Circuit
Transmission Line: 90º @ Fo
RF Input
RF Output
MA4L032-134
Coil: D.C. Return
MA4L022-134
Specification Subject to Change Without Notice
M/A-COM Inc. 43 South Avenue, Burlington, MA 01803 USA
5
þ
þ
Telephone: 781-564-3100
Silicon PIN Limiter Diodes
MA4L Series
V 5.0
Popular Case Styles and Associated Parasitics ( Table I )
Package Style
Package Type
Cpkg ( pF )
0.18
Ls ( nH )
0.60
30
Ceramic Pill
31
Ceramic Pill
0.18
0.60
32
Ceramic Pill
0.30
0.40
36
Ceramic Pill
0.18
0.60
137
Ceramic Surface Mount with Leads
0.14
0.70
186
Ceramic Surface Mount with Leads
0.18
0.70
Ceramic Surface Mount with
1056
0.20
0.70
Wrap Around Contacts
Part Numbering and Ordering Information
1. The die only P/N’s use either the -132 or -134 suffix (see Electrical Specification Table).
2. The packaged P/N’s use the associated suffix as defined in Table I instead of the die number.
For example, the MA4L032-134 die in the 186 style package becomes: MA4L032-186
Specification Subject to Change Without Notice
6
M/A-COM Inc.
þ
43 South Avenue, Burlington, MA 01803 USA
þ
Telephone: 781-564-3100
相关型号：
©2020 ICPDF网 联系我们和版权申明