MD-169PIN [TE]
Termination Insensitive Mixer, 1 MHz - 3.5 GHz; 终止不敏感搅拌机, 1兆赫 - 3.5 GHz的型号: | MD-169PIN |
厂家: | TE CONNECTIVITY |
描述: | Termination Insensitive Mixer, 1 MHz - 3.5 GHz |
文件: | 总4页 (文件大小:251K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Termination Insensitive Mixer,
1 MHz - 3.5 GHz
V 3.00
Features
FP-2 (MD-169)
n
n
n
n
n
Intermodulation Ratio is Insensitive to Port Mismatches
VSWR: <2.0:1 Typical Midband
Isolation: 35 dB Typical Midband
Impedance: 50 Ohms Nominal
Maximum Input Power: 350 mW Max @ 25°C, Derated
to 85°C @ 3.2 mW/°C
n
n
LO Power: +24 dBm Max.
MIL-STD-883 Screening Available
Description
The unique design of the termination insensitive mixer
(TIM) enables it to apply high reverse voltage to diodes
during their “off” phase, in the LO cycle. This allows for
higher power level performance with minimum distortion.
In addition the TIM has internal loads that provide a good
match and also absorb mixer generated LO frequency
terms. Combined, these features give the mixer its
insensitivity to external mismatches, plus superior VSWR.
C-7 (MDC-169)
SF-1 (MDS-169)
Termination-Insensitive Mixer, 1 MHz - 3.5 GHz
MD-/MDC-/MDS-169
V 3.00
Electrical Specifications1(MD-/MDC-169): TA = -55°C to +85°C
Parameter
Test Conditions
Frequency
Units
Min
Typ
Max
Frequency Range
Conversion Loss
RF, LO Ports
IF Port
0.001 - 3.5
5 - 1500
GHz
MHz
—
—
—
—
—
—
5 - 1000 MHz 2
5 - 3000 MHz 3
1 - 3500 MHz
dB
dB
dB
—
—
—
—
—
—
7
8
10
Isolation
LO to RF
LO to IF
RF to IF
5 - 1000 MHz
1 - 3500 MHz
dB
dB
30
20
—
—
—
—
5 - 1000 MHz
1 - 3500 MHz
dB
dB
30
20
—
—
—
—
10 - 500 MHz
1 - 3000 MHz
1 - 3500 MHz
dB
dB
dB
30
20
18
—
—
—
—
—
—
RF Input
1 dB Compression
1 dB Desensitization
—
—
dBm
dBm
—
—
+7
+5
—
—
SSB Noise Figure
Within 1 dB of Conversion Loss
Max
—
—
—
—
—
Typical Two-Tone IM
Ratio
with a –10 dBm input, each input,
25 MHz and 35 MHz IF
10 MHz
500 MHz
3000 MHz
dB
dB
dB
—
—
—
55
58
56
—
—
—
3rd Order
Intermodulation Ratio
Degradation
@ IF VSWR 3:1
—
dB
—
3
—
1. All specifications apply when operated at +10 available LO power with 50 Ohm source and load impedance.
2. For IF Frequencies of 5 - 300 MHz and RF of –10 dBm or less.
3. For MDC-169, add 1.0 dB to conversion loss.
Electrical Specifications (MDS-169): TA = -55°C to +85°C,
Frequency: RF, LO Ports = 1 - 3500 MHz, IF Port = 5 - 1500 MHz
Parameter
Test Conditions
Frequency
Units
Min
Typ
Max
Conversion Loss
LO @ +10 dBm
IF @ 60 MHz
5 - 1000 MHz
1000 - 3000 MHz
1 - 3500 MHz
dB
dB
dB
—
—
—
6.5
7.5
8.0
7.0
9.0
10.0
Isolation
LO to RF
LO to IF
RF to IF
5 - 1000 MHz
1 - 3500 MHz
dB
dB
30
20
35
25
—
—
5 - 1000 MHz
1 - 3500 MHz
dB
dB
30
20
35
25
—
—
10 - 500 MHz
1 - 3000 MHz
1 - 3500 MHz
dB
dB
dB
30
20
18
35
25
23
—
—
—
2
Specifications subject to change without notice.
n North America: Tel. (800) 366-2266
n Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298
n Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020
Visit www.macom.com for additional data sheets and product information.
Termination-Insensitive Mixer, 1 MHz - 3.5 GHz
Pin Configuration (MD-169)
MD-/MDC-/MDS-169
V 3.00
Absolute Maximum Ratings
(MDS-169) 4
Pin No.
Function
Pin No.
Function
1
2
3
4
GND
GND
GND
IF
5
6
7
8
LO
GND
GND
RF
Parameter
Max Input Power 5
Total Power
Absolute Maximum
350 mW Derated to 85°C @
3.2 mW/°C
LO Power
+24 dBm
Bottom View of SF-1
4. Operation of this device above any one of these
parameters may cause permanent damage.
5. Ambient Temperature (TA) = +25°C
4X .016 ± .002
.506
.385 Ref
.220
.165
.381
.002
.000
Typical Performance Curves
Isolation - Input +10 dBm
Conversion Loss - LO @ +10 dBm,
IF @ 60 MHz
L-R
L-I
R-I
60
50
40
30
20
10
0
10
9
8
7
6
5
4
0
1
3
10
30
100 1000 2000 3000 4000
0
1
3
10
30
100 1000 2000 3000 4000
Frequency (MHz)
Frequency (MHz)
3
Specifications subject to change without notice.
n North America: Tel. (800) 366-2266
n Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298
n Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020
Visit www.macom.com for additional data sheets and product information.
Termination-Insensitive Mixer, 1 MHz - 3.5 GHz
Typical Performance Curves
MD-/MDC-/MDS-169
V 3.00
3rd Order IM Ratio - LO @ +10 dBm,
Conversion Loss vs. LO Power - RF
@ 2000 MHz –10 dBm, IF @ 60 MHz
IF Port Terminated
with 3.0:1 Mismatch
IF Port Match
65
60
55
50
45
10
9
8
7
6
0
2
4
6
8
10
12
14
0
1
3
10
30
100 1000 2000 3000 4000
LO Power (dBm)
Frequency (MHz)
IF Port Response
VSWR
IF
RF
LO
3
2.5
2
2.0
1.5
1.0
0.5
0.0
1.5
1
0
1
3
10
30
100 1000 2000 3000 4000
0
1
3
10
30
100 1000 2000 3000 4000
IF Frequency (MHz)
Frequency (MHz)
Ordering Information
Part Number
Package
MD-169 PIN
FP-2
MDC-169 SMA
MDS-169
C-7
SF-1
4
Specifications subject to change without notice.
n North America: Tel. (800) 366-2266
n Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298
n Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020
Visit www.macom.com for additional data sheets and product information.
相关型号:
©2020 ICPDF网 联系我们和版权申明