5962-9153202QPA [TI]
DUAL MICROPOWER LinCMOS VOLTAGE COMPARATORS; 双通道,微路LinCMOS电压比较器型号: | 5962-9153202QPA |
厂家: | TEXAS INSTRUMENTS |
描述: | DUAL MICROPOWER LinCMOS VOLTAGE COMPARATORS |
文件: | 总36页 (文件大小:1139K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TLC3702
DUAL MICROPOWER LinCMOS™ VOLTAGE COMPARATORS
SLCS013E − NOVEMBER 1986 − REVISED MARCH 2012
D, JG, OR P PACKAGE
D Push-Pull CMOS Output Drives Capacitive
(TOP VIEW)
Loads Without Pullup Resistor,
I = 8 mA
O
1OUT
1IN−
1IN+
GND
VDD
1
2
3
4
8
7
6
5
D Very Low Power . . . 100 μW Typ at 5 V
2OUT
2IN−
2IN+
D Fast Response Time . . . t
= 2.7 μs Typ
PLH
With 5-mV Overdrive
D Single-Supply Operation . . . 3 V to 16 V
TLC3702M . . . 4 V to 16 V
FK PACKAGE
(TOP VIEW)
D On-Chip ESD Protection
description
The TLC3702 consists of two independent
micropower voltage comparators designed to
operate from a single supply and be compatible
with modern HCMOS logic systems. They are
functionally similar to the LM339 but use one-
twentieth of the power for similar response times.
The push-pull CMOS output stage drives
capacitive loads directly without a power-
consuming pullup resistor to achieve the stated
response time. Eliminating the pullup resistor not
only reduces power dissipation, but also saves
board space and component cost. The output
stage is also fully compatible with TTL
requirements.
3
2
1
20 19
18
NC
2OUT
NC
2IN−
NC
NC
1IN−
NC
1IN+
NC
4
5
6
7
8
17
16
15
14
9 10 11 12 13
NC − No internal connection
symbol (each comparator)
Texas Instruments LinCMOS™ process offers
superior analog performance to standard CMOS
processes. Along with the standard CMOS
advantages of low power without sacrificing
speed, high input impedance, and low bias
currents, the LinCMOS™ process offers
extremely stable input offset voltages with large
differential input voltages. This characteristic
makes it possible to build reliable CMOS
comparators.
IN+
OUT
IN−
The TLC3702C is characterized for operation over the commercial temperature range of 0°C to 70°C. The
TLC3702I is characterized for operation over the extended industrial temperature range of −40°C to 85°C. The
TLC3702M is characterized for operation over the full military temperature range of −55°C to 125°C.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
LinCMOS is a trademark of Texas Instruments Incorporated.
Copyright © 1998, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC3702
DUAL MICROPOWER LinCMOS™ VOLTAGE COMPARATORS
SLCS013E − NOVEMBER 1986 − REVISED MARCH 2012
AVAILABLE OPTIONS
PACKAGES
V
max
IO
T
A
SMALL OUTLINE
(D)
CERAMIC
(FK)
CERAMIC DIP
(JG)
PLASTIC DIP
(P)
at 25°C
0°C to 70°C
−40°C to 85°C
−55°C to 125°C
5 mV
5 mV
5 mV
TLC3702CD
TLC3702ID
TLC3702MD
—
—
—
—
TLC3702CP
TLC3702IP
—
TLC3702MFK
TLC3702MJG
The D package is available taped and reeled. Add R suffix to the device type (e.g., TLC3702CDR).
functional block diagram (each comparator)
V
DD
IN+
Differential
Input
Circuits
OUT
IN−
GND
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range, V (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 18 V
DD
Differential input voltage, V (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 V
ID
Input voltage range, V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to V
I
DD
Output voltage range, V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . − 0.3 V to V
O
DD
Input current, I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 mA
I
Output current, I (each output) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 mA
O
Total supply current into V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 mA
DD
Total current out of GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 mA
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating free-air temperature range, T : TLC3702C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
A
TLC3702I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to 85°C
TLC3702M . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −55°C to 125°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
Case temperature for 60 seconds: FK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: D or P package . . . . . . . . . . . . . . . . . 260°C
Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: JG package . . . . . . . . . . . . . . . . . . . . 300°C
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential voltages, are with respect to network ground.
2. Differential voltages are at IN+ with respect to IN−.
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC3702
DUAL MICROPOWER LinCMOS™ VOLTAGE COMPARATORS
SLCS013E − NOVEMBER 1986 − REVISED MARCH 2012
DISSIPATION RATING TABLE
T
≤ 25°C
DERATING FACTOR
T
= 70°C
T
= 85°C
T = 125°C
A
POWER RATING
A
A
A
PACKAGE
POWER RATING
ABOVE T = 25°C
POWER RATING
POWER RATING
A
D
FK
JG
P
725 mW
5.8 mW/°C
11.0 mW/°C
8.4 mW/°C
8.0 mW/°C
464 mW
377 mW
145 mW
1375 mW
880 mW
715 mW
275 mW
1050 mW
672 mW
546 mW
210 mW
1000 mW
640 mW
520 mW
N/A
recommended operating conditions
TLC3702C
MIN NOM
UNIT
MAX
Supply voltage, V
3
5
16
V
V
DD
Common-mode input voltage, V
− 0.2
V
− 1.5
DD
IC
High-level output current, I
−20
mA
mA
°C
OH
OL
Low-level output current, I
20
70
Operating free-air temperature, T
0
A
electrical characteristics at specified operating free-air temperature, VDD = 5 V (unless otherwise
noted)
TLC3702C
†
PARAMETER
T
A
UNIT
TEST CONDITIONS
MIN
TYP
MAX
V
V
= 5 V to 10 V,
25°C
1.2
5
DD
= V min,
V
Input offset voltage
mV
IC
ICR
IO
0°C to 70°C
6.5
See Note 3
25°C
70°C
1
5
pA
nA
pA
nA
I
I
Input offset current
V
V
= 2.5 V
= 2.5 V
IO
IC
IC
0.3
0.6
25°C
Input bias current
IB
70°C
25°C
0 to V − 1
DD
V
Common-mode input voltage range
V
ICR
0°C to 70°C
25°C
0 to V − 1.5
DD
84
84
84
85
85
85
4.7
70°C
CMRR Common-mode rejection ratio
V
= V min
dB
IC
ICR
0°C
25°C
70°C
k
Supply-voltage rejection ratio
V
V
= 5 V to 10 V
dB
SVR
DD
0°C
25°C
4.5
4.3
= 1 V,
= −4 mA
ID
V
V
High-level output voltage
V
OH
OL
I
OH
70°C
25°C
210
18
300
375
40
V
= −1 V,
= 4 mA
ID
Low-level output voltage
mV
μA
I
OH
70°C
25°C
I
Supply current (both comparators)
Outputs low, No load
DD
0°C to 70°C
50
†
All characteristics are measured with zero common-mode voltage unless otherwise noted.
NOTE 3: The offset voltage limits given are the maximum values required to drive the output up to 4.5 V or down to 0.3 V.
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC3702
DUAL MICROPOWER LinCMOS™ VOLTAGE COMPARATORS
SLCS013E − NOVEMBER 1986 − REVISED MARCH 2012
recommended operating conditions
TLC3702I
MIN NOM
UNIT
MAX
Supply voltage, V
3
5
16
V
V
DD
Common-mode input voltage, V
−0.2
V
− 1.5
DD
IC
High-level output current, I
−20
mA
mA
°C
OH
OL
Low-level output current, I
20
85
Operating free-air temperature, T
−40
A
electrical characteristics at specified operating free-air temperature, VDD = 5 V (unless otherwise
noted)
TLC3702I
†
PARAMETER
Input offset voltage
Input offset current
Input bias current
T
UNIT
TEST CONDITIONS
A
MIN
TYP
MAX
25°C
−40°C to 85°C
25°C
1.2
5
7
V
V
= 5 V to 10 V,
DD
V
mV
IO
= V min, See Note 3
IC
ICR
1
5
pA
nA
pA
nA
I
I
V
V
= 2.5 V
= 2.5 V
IO
IC
85°C
1
2
25°C
IB
IC
85°C
0 to
25°C
V
− 1
DD
V
Common-mode input voltage range
V
ICR
0 to
−40°C to 85°C
V
− 1.5
DD
25°C
85°C
84
84
83
85
85
83
4.7
CMRR Common-mode rejection ratio
V
V
= V min
dB
dB
IC
ICR
−40°C
25°C
85°C
k
Supply-voltage rejection ratio
= 5 V to 10 V
DD
SVR
−40°C
25°C
4.5
4.3
V
V
High-level output voltage
V
V
= 1 V,
I
I
= −4 mA
= −4 mA
V
OH
OL
ID
ID
OH
OH
85°C
25°C
210
18
300
400
40
Low-level output voltage
= −1 V,
mV
μA
85°C
25°C
I
Supply current (both comparators)
Outputs low, No load
DD
−40°C to 85°C
65
†
All characteristics are measured with zero common-mode voltage unless otherwise noted.
NOTE 3. The offset voltage limits given are the maximum values required to drive the output up to 4.5 V or down to 0.3 V.
4
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC3702
DUAL MICROPOWER LinCMOS™ VOLTAGE COMPARATORS
SLCS013E − NOVEMBER 1986 − REVISED MARCH 2012
recommended operating conditions
TLC3702M
MIN NOM MAX
UNIT
Supply voltage, V
4
0
5
16
V
V
DD
Common-mode input voltage, V
V
− 1.5
DD
IC
High-level output current, I
− 20
20
125
mA
mA
°C
OH
OL
Low-level output current, I
Operating free-air temperature, T
− 55
A
electrical characteristics at specified operating free-air temperature, VDD = 5 V (unless otherwise
noted)
TLC3702M
†
PARAMETER
Input offset voltage
Input offset current
Input bias current
T
UNIT
TEST CONDITIONS
A
MIN
TYP
MAX
5
25°C
−55°C to 125°C
25°C
1.2
V
V
= 5 V to 10 V,
DD
V
mV
IO
= V min, See Note 3
10
IC
ICR
1
5
pA
nA
pA
nA
I
I
V
V
= 2.5 V
= 2.5 V
IO
IC
125°C
15
30
25°C
IB
IC
125°C
0 to
25°C
V
− 1
DD
V
Common-mode input voltage range
V
ICR
0 to
−55°C to 125°C
V
− 1.5
DD
25°C
125°C
84
83
82
85
85
82
4.7
CMRR Common-mode rejection ratio
V
V
= V min
dB
dB
IC
ICR
−55°C
25°C
125°C
k
Supply-voltage rejection ratio
= 5 V to 10 V
DD
SVR
− 55°C
25°C
4.5
4.2
V
V
High-level output voltage
V
V
= 1 V,
I
I
= −4 mA
= −4 mA
V
OH
OL
ID
ID
OH
OH
125°C
25°C
210
18
300
500
40
Low-level output voltage
= −1 V,
mV
μA
125°C
25°C
I
Supply current (both comparators)
Outputs low, No load
DD
−55°C to 125°C
90
†
All characteristics are measured with zero common-mode voltage unless otherwise noted.
NOTE 3. The offset voltage limits given are the maximum values required to drive the output up to 4.5 V or down to 0.3 V.
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC3702
DUAL MICROPOWER LinCMOS™ VOLTAGE COMPARATORS
SLCS013E − NOVEMBER 1986 − REVISED MARCH 2012
switching characteristics, VDD = 5 V, TA = 25°C
TLC3702C, TLC3702I
TLC3702M
PARAMETER
TEST CONDITIONS
UNIT
MIN
TYP
4.5
2.7
1.9
1.4
1.1
1.1
4
MAX
Overdrive = 2 mV
Overdrive = 5 mV
f = 10 kHz,
C = 50 pF
†
Overdrive = 10 mV
Overdrive = 20 mV
Overdrive = 40 mV
t
t
Propagation delay time, low-to-high-level output
μs
PLH
L
V = 1.4 V step at IN+
I
Overdrive = 2 mV
Overdrive = 5 mV
Overdrive = 10 mV
Overdrive = 20 mV
Overdrive = 40 mV
2.3
1.5
0.95
0.65
0.15
f = 10 kHz,
C = 50 pF
†
Propagation delay time, high-to-low-level output
μs
PHL
L
V = 1.4 V step at IN+
I
f = 10 kHz,
C = 50 pF
L
t
t
Fall time
Overdrive = 50 mV
Overdrive = 50 mV
50
ns
ns
f
f = 10 kHz,
C = 50 pF
L
Rise time
125
r
†
Simultaneous switching of inputs causes degradation in output response.
6
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC3702
DUAL MICROPOWER LinCMOS™ VOLTAGE COMPARATORS
SLCS013E − NOVEMBER 1986 − REVISED MARCH 2012
PRINCIPLES OF OPERATION
LinCMOS™ process
The LinCMOS™ process is a linear polysilicon-gate CMOS process. Primarily designed for single-supply
applications, LinCMOS™ products facilitate the design of a wide range of high-performance analog functions
from operational amplifiers to complex mixed-mode converters.
While digital designers are experienced with CMOS, MOS technologies are relatively new for analog designers.
This short guide is intended to answer the most frequently asked questions related to the quality and reliability
of LinCMOS™ products. Further questions should be directed to the nearest TI field sales office.
electrostatic discharge
CMOS circuits are prone to gate oxide breakdown when exposed to high voltages even if the exposure is only
for very short periods of time. Electrostatic discharge (ESD) is one of the most common causes of damage to
CMOS devices. It can occur when a device is handled without proper consideration for environmental
electrostatic charges, e.g., during board assembly. If a circuit in which one amplifier from a dual op amp is being
used and the unused pins are left open, high voltages tend to develop. If there is no provision for ESD protection,
these voltages may eventually punch through the gate oxide and cause the device to fail. To prevent voltage
buildup, each pin is protected by internal circuitry.
Standard ESD-protection circuits safely shunt the ESD current by providing a mechanism whereby one or more
transistors break down at voltages higher than the normal operating voltages but lower than the breakdown
voltage of the input gate. This type of protection scheme is limited by leakage currents which flow through the
shunting transistors during normal operation after an ESD voltage has occurred. Although these currents are
small, on the order of tens of nanoamps, CMOS amplifiers are often specified to draw input currents as low as
tens of picoamps.
To overcome this limitation, TI design engineers developed the patented ESD-protection circuit shown in
Figure 1. This circuit can withstand several successive 2-kV ESD pulses, while reducing or eliminating leakage
currents that may be drawn through the input pins. A more detailed discussion of the operation of the TI
ESD-protection circuit is presented on the next page.
All input and output pins on LinCMOS™ and Advanced LinCMOS™ products have associated ESD-protection
circuitry that undergoes qualification testing to withstand 2000 V discharged from a 100-pF capacitor through
a 1500-Ω resistor (human body model) and 200 V from a 100-pF capacitor with no current-limiting resistor
(charged device model). These tests simulate both operator and machine handling of devices during normal
test and assembly operations.
V
DD
R1
Input
To Protect Circuit
R2
Q1
Q2
D1
D2
D3
GND
Figure 1. LinCMOS™ ESD-Protection Schematic
LinCMOS and Advanced LinCMOS are trademarks of Texas Instruments Incorporated.
7
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC3702
DUAL MICROPOWER LinCMOS™ VOLTAGE COMPARATORS
SLCS013E − NOVEMBER 1986 − REVISED MARCH 2012
PRINCIPLES OF OPERATION
input protection circuit operation
Texas Instruments patented protection circuitry allows for both positive- and negative-going ESD transients.
These transients are characterized by extremely fast rise times and usually low energies, and can occur both
when the device has all pins open and when it is installed in a circuit.
positive ESD transients
Initial positive charged energy is shunted through Q1 to V . Q1 turns on when the voltage at the input rises
SS
above the voltage on the V pin by a value equal to the V of Q1. The base current increases through R2
DD
BE
with input current as Q1 saturates. The base current through R2 forces the voltage at the drain and gate of Q2
to exceed its threshold level (V ∼ 22 to 26 V) and turn Q2 on. The shunted input current through Q1 to V is
T
SS
now shunted through the n-channel enhancement-type MOSFET Q2 to V . If the voltage on the input pin
SS
continues to rise, the breakdown voltage of the zener diode D3 is exceeded and all remaining energy is
dissipated in R1 and D3. The breakdown voltage of D3 is designed to be 24 V to 27 V, which is well below the
gate-oxide voltage of the circuit to be protected.
negative ESD transients
The negative charged ESD transients are shunted directly through D1. Additional energy is dissipated in R1
and D2 as D2 becomes forward biased. The voltage seen by the protected circuit is −0.3 V to −1 V (the forward
voltage of D1 and D2).
circuit-design considerations
LinCMOS™ products are being used in actual circuit environments that have input voltages that exceed the
recommended common-mode input voltage range and activate the input protection circuit. Even under normal
operation, these conditions occur during circuit power up or power down, and in many cases, when the device
is being used for a signal conditioning function. The input voltages can exceed V
and not damage the device
ICR
only if the inputs are current limited. The recommended current limit shown on most product data sheets is
5 mA. Figure 2 and Figure 3 show typical characteristics for input voltage versus input current.
Normal operation and correct output state can be expected even when the input voltage exceeds the positive
supply voltage. Again, the input current should be externally limited even though internal positive current limiting
is achieved in the input protection circuit by the action of Q1. When Q1 is on, it saturates and limits the current
to approximately 5-mA collector current by design. When saturated, Q1 base current increases with input
current. This base current is forced into the V pin and into the device I
or the V supply through R2
DD
DD
DD
producing the current limiting effects shown in Figure 2. This internal limiting lasts only as long as the input
voltage is below the V of Q2.
T
When the input voltage exceeds the negative supply voltage, normal operation is affected and output voltage
states may not be correct. Also, the isolation between channels of multiple devices (duals and quads) can be
severely affected. External current limiting must be used since this current is directly shunted by D1 and D2 and
no internal limiting is achieved. If normal output voltage states are required, an external input voltage clamp is
required (see Figure 4).
8
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC3702
DUAL MICROPOWER LinCMOS™ VOLTAGE COMPARATORS
SLCS013E − NOVEMBER 1986 − REVISED MARCH 2012
PRINCIPLES OF OPERATION
circuit-design considerations (continued)
INPUT CURRENT
vs
POSITIVE INPUT VOLTAGE
INPUT CURRENT
vs
NEGATIVE INPUT VOLTAGE
8
7
−10
−9
T
A
= 25° C
T = 25° C
A
−8
−7
6
5
−6
−5
4
3
2
1
0
−4
−3
−2
−1
−0
V
V
+ 4
V
+ 8
V + 12
DD
−0.3
−0.5
−0.7
−0.9
DD
DD
DD
V − Input Voltage − V
I
V − Input Voltage − V
I
Figure 2
Figure 3
V
DD
R
I
Positive Voltage Input Current Limit :
V
+
I
1/2
VI * VDD * 0.3 V
TLC3702
RI
+
5 mA
−
V
ref
Negative Voltage Input Current Limit :
* VI * VDD * (* 0.3 V)
RI
+
5 mA
See Note A
NOTE A: If the correct input state is required when the negative input exceeds GND, a Schottky clamp is required.
Figure 4. Typical Input Current-Limiting Configuration for a LinCMOS™ Comparator
9
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC3702
DUAL MICROPOWER LinCMOS™ VOLTAGE COMPARATORS
SLCS013E − NOVEMBER 1986 − REVISED MARCH 2012
PARAMETER MEASUREMENT INFORMATION
The TLC3702 contains a digital output stage which, if held in the linear region of the transfer curve, can cause
damage to the device. Conventional operational amplifier/comparator testing incorporates the use of a servo
loop which is designed to force the device output to a level within this linear region. Since the servo-loop method
of testing cannot be used, we offer the following alternatives for measuring parameters such as input offset
voltage, common-mode rejection, etc.
To verify that the input offset voltage falls within the limits specified, the limit value is applied to the input as shown
in Figure 5(a). With the noninverting input positive with respect to the inverting input, the output should be high.
With the input polarity reversed, the output should be low.
A similar test can be made to verify the input offset voltage at the common-mode extremes. The supply voltages
can be slewed to provide greater accuracy, as shown in Figure 5(b) for the V
of changing the input voltages.
test. This slewing is done instead
ICR
A close approximation of the input offset voltage can be obtained by using a binary search method to vary the
differential input voltage while monitoring the output state. When the applied input voltage differential is equal,
but opposite in polarity, to the input offset voltage, the output changes states.
Figure 6 illustrates a practical circuit for direct dc measurement of input offset voltage that does not bias the
comparator in the linear region. The circuit consists of a switching mode servo loop in which IC1a generates
a triangular waveform of approximately 20-mV amplitude. IC1b acts as a buffer, with C2 and R4 removing any
residual dc offset. The signal is then applied to the inverting input of the comparator under test, while the
noninverting input is driven by the output of the integrator formed by IC1c through the voltage divider formed
by R8 and R9. The loop reaches a stable operating point when the output of the comparator under test has a
duty cycle of exactly 50%, which can only occur when the incoming triangle wave is sliced symmetrically or when
the voltage at the noninverting input exactly equals the input offset voltage.
Voltage dividers R8 and R9 provide an increase in input offset voltage by a factor of 100 to make measurement
easier. The values of R5, R7, R8, and R9 can significantly influence the accuracy of the reading; therefore, it
is suggested that their tolerance level be one percent or lower.
Measuring the extremely low values of input current requires isolation from all other sources of leakage current
and compensation for the leakage of the test socket and board. With a good picoammeter, the socket and board
leakage can be measured with no device in the socket. Subsequently, this open socket leakage value can be
subtracted from the measurement obtained with a device in the socket to obtain the actual input current of the
device.
5 V
1 V
+
+
−
−
Applied V
Applied V
IO
IO
Limit
Limit
V
V
O
O
− 4 V
(a) V WITH V = 0 V
(b) V WITH V = 4 V
IO IC
IO
IC
Figure 5. Method for Verifying That Input Offset Voltage Is Within Specified Limits
10
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC3702
DUAL MICROPOWER LinCMOS™ VOLTAGE COMPARATORS
SLCS013E − NOVEMBER 1986 − REVISED MARCH 2012
PARAMETER MEASUREMENT INFORMATION
V
DD
C3
0.68 μF
R5
1.8 kΩ 1%
IC1a
1/4 TLC274CN
C2
1 μF
IC1c
Buffer
+
1/4 TLC274CN
R6
1 MΩ
−
DUT
−
−
V
IO
+
R4
47 kΩ
(X100)
+
Integrator
R7
1.8 kΩ 1%
R1
240 kΩ
IC1b
1/4 TLC274CN
C4
0.1 μF
−
C1
0.1 μF
+
Triangle
Generator
R8
10 kΩ 1%
R9
100 Ω 1%
R2
10 kΩ
R3
100 Ω
Figure 6. Circuit for Input Offset Voltage Measurement
Response time is defined as the interval between the application of an input step function and the instant when
the output reaches 50% of its maximum value. Response time for the low-to-high-level output is measured from
the leading edge of the input pulse, while response time for the high-to-low-level output is measured from the
trailing edge of the input pulse. Response time measurement at low input signal levels can be greatly affected
by the input offset voltage. The offset voltage should be balanced by the adjustment at the inverting input as
shown in Figure 7, so that the circuit is just at the transition point. A low signal, for example 105-mV or 5-mV
overdrive, causes the output to change state.
11
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC3702
DUAL MICROPOWER LinCMOS™ VOLTAGE COMPARATORS
SLCS013E − NOVEMBER 1986 − REVISED MARCH 2012
PARAMETER MEASUREMENT INFORMATION
V
DD
Pulse
Generator
μ
F
1
Ω
50
+
1 V
DUT
10 Ω
−
C
L
10-Turn
Potentiometer
(see Note A)
1 kΩ
μ
F
0.1
− 1 V
TEST CIRCUIT
Overdrive
Overdrive
Input
100 mV
Input
100 mV
90%
50%
10%
90%
50%
10%
Low-to-High
Level Output
High-to-Low
Level Output
t
r
t
f
t
t
PHL
PLH
VOLTAGE WAVEFORMS
NOTE A: C includes probe and jig capacitance.
L
Figure 7. Response, Rise, and Fall Times Circuit and Voltage Waveforms
12
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC3702
DUAL MICROPOWER LinCMOS™ VOLTAGE COMPARATORS
SLCS013E − NOVEMBER 1986 − REVISED MARCH 2012
TYPICAL CHARACTERISTICS†
Table of Graphs
FIGURE
V
Input offset voltage
Input bias current
Distribution
8
9
IO
I
vs Free-air temperature
vs Free-air temperature
vs Free-air temperature
IB
CMRR Common-mode rejection ratio
10
11
k
Supply-voltage rejection ratio
SVR
vs Free-air temperature
vs High-level output current
12
13
V
V
High-level output current
OH
OL
vs Low-level output current
vs Free-air temperature
14
15
Low-level output voltage
t
Transition time
vs Load capacitance
16
17
18
19
20
21
t
Supply current response
Low-to-high-level output response
High-to-low level output response
vs Time
Low-to-high level output propagation delay time
High-to-low level output propagation delay time
t
t
Low-to-high level output propagation delay time vs Supply voltage
High-to-low level output propagation delay time vs Supply voltage
vs Frequency
PLH
PHL
22
23
24
vs Supply voltage
vs Free-air temperature
I
Supply current
DD
INPUT BIAS CURRENT
vs
FREE-AIR TEMPERATURE
DISTRIBUTION OF INPUT
OFFSET VOLTAGE
200
180
160
140
10
V
V
= 5 V
DD
V
V
= 5 V
DD
IC
= 2.5 V
IC
= 2.5 V
T
= 25° C
A
698 Units Tested
From 4 Wafer Lots
1
0.1
120
100
80
60
40
20
0.01
0.001
0
−5 −4 −3 −2 −1
0
1
2
3
4
5
25
50
75
100
125
V
− Input Offset Voltage − mV
T
A
− Free-Air Temperature − °C
IO
Figure 8
Figure 9
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
13
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC3702
DUAL MICROPOWER LinCMOS™ VOLTAGE COMPARATORS
SLCS013E − NOVEMBER 1986 − REVISED MARCH 2012
TYPICAL CHARACTERISTICS†
SUPPLY VOLTAGE REJECTION RATIO
COMMON-MODE REJECTION RATIO
vs
vs
FREE-AIR TEMPERATURE
FREE-AIR TEMPERATURE
90
88
86
84
82
90
88
86
84
82
80
78
76
V
= 5 V to 10 V
V
= 5 V
DD
DD
80
78
76
74
72
70
74
72
70
−75 −50 −25
0
25
50
75
100 125
−75 −50 −25
0
25
50
75
100 125
T
A
− Free-Air Temperature − °C
T
A
− Free-Air Temperature − °C
Figure 10
Figure 11
HIGH-LEVEL OUTPUT VOLTAGE
vs
HIGH-LEVEL OUTPUT CURRENT
HIGH-LEVEL OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
5
4.95
4.9
V
DD
V
OH
= 5 V
DD
I
= − 4 mA
V
= 16 V
10 V
−0.25
DD
−0.5
4.85
4.8
−0.75
4.75
−1
5 V
4.7
−1.25
4.65
4 V
−1.5
4.6
4.55
4.5
3 V
−1.75
−2
T
A
= 25° C
0
−2.5 −5 −7.5 −10 −12.5 −15 −17.5 −20
−75 −50 −25
0
25
50
75
100
125
I
− High-Level Output Current − mA
T
A
− Free-Air Temperature − °C
OH
Figure 12
Figure 13
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
14
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC3702
DUAL MICROPOWER LinCMOS™ VOLTAGE COMPARATORS
SLCS013E − NOVEMBER 1986 − REVISED MARCH 2012
TYPICAL CHARACTERISTICS†
LOW-LEVEL OUTPUT VOLTAGE
LOW-LEVEL OUTPUT VOLTAGE
vs
vs
LOW-LEVEL OUTPUT CURRENT
FREE-AIR TEMPERATURE
1.5
400
350
300
250
200
150
100
T
A
= 25°C
V
I
= 5 V
DD
3 V
= 4 mA
4 V
OL
1.25
5 V
1
0.75
10 V
0.5
0.25
V
= 16 V
DD
50
0
0
0
2
4
6
8
10 12 14 16 18
20
−75 −50 −25
0
25
50
75
100 125
I
− Low-Level Output Current − mA
OL
T
A
− Free-Air Temperature − °C
Figure 14
Figure 15
OUTPUT TRANSITION TIME
vs
SUPPLY CURRENT RESPONSE
TO AN OUTPUT VOLTAGE TRANSITION
LOAD CAPACITANCE
250
225
200
V
C
= 5 V
= 50 pF
DD
V
T
A
= 5 V
= 25°C
DD
L
f = 10 kHz
10
Rise Time
175
150
125
100
75
5
0
5
0
Fall Time
50
25
0
0
200
400
600
800
1000
t − Time
C
L
− Load Capacitance − pF
Figure 16
Figure 17
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
15
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC3702
DUAL MICROPOWER LinCMOS™ VOLTAGE COMPARATORS
SLCS013E − NOVEMBER 1986 − REVISED MARCH 2012
TYPICAL CHARACTERISTICS
LOW-TO-HIGH-LEVEL OUTPUT RESPONSE
FOR VARIOUS INPUT OVERDRIVES
HIGH-TO-LOW-LEVEL OUTPUT RESPONSE
FOR VARIOUS INPUT OVERDRIVES
5
5
40 mV
20 mV
10 mV
5 mV
40 mV
20 mV
10 mV
5 mV
2 mV
2 mV
0
100
0
0
100
0
V
T
C
= 5 V
= 25° C
= 50 pF
DD
A
L
V
= 5 V
= 25°C
= 50 pF
DD
T
A
C
L
0
1
2
3
4
5
0
1
2
3
4
5
t
− Low-to-High-Level Output
Response Time − μs
t
− High-to-Low-Level Output
Response Time − μs
PLH
PHL
Figure 18
Figure 19
LOW-TO-HIGH-LEVEL
HIGH-TO-LOW-LEVEL
OUTPUT RESPONSE TIME
vs
OUTPUT RESPONSE TIME
vs
SUPPLY VOLTAGE
SUPPLY VOLTAGE
6
5
6
5
C
= 50 pF
= 25°C
L
C
= 50 pF
= 25°C
L
T
A
T
A
Overdrive = 2 mV
Overdrive = 2 mV
4
3
2
1
0
4
3
5 mV
10 mV
5 mV
2
10 mV
20 mV
20 mV
40 mV
1
0
40 mV
6
0
2
4
6
8
10
12
14
16
0
2
4
8
10
12
14
16
V
− Supply Voltage − V
DD
V
− Supply Voltage − V
DD
Figure 20
Figure 21
16
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC3702
DUAL MICROPOWER LinCMOS™ VOLTAGE COMPARATORS
SLCS013E − NOVEMBER 1986 − REVISED MARCH 2012
TYPICAL CHARACTERISTICS†
AVERAGE SUPPLY CURRENT
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
(PER COMPARATOR)
vs
FREQUENCY
40
35
10000
1000
Outputs Low
No Loads
T
= − 55°C
A
T
C
= 25°C
= 50 pF
A
T = − 40°C
A
L
V
= 16 V
DD
30
25
20
15
10
T
= − 25°C
10 V
A
5 V
100
10
T
= − 125°C
A
4 V
T
= 85°C
A
5
0
3 V
0
1
2
3
4
5
6
7
8
0.01
0.1
1
10
100
f − Frequency − kHz
V
− Supply Voltage − V
DD
Figure 22
Figure 23
SUPPLY CURRENT
vs
FREE-AIR TEMPERATURE
30
25
20
15
V
= 5 V
DD
No Load
Outputs Low
Outputs High
10
5
0
−75 −50 −25
0
25
50
75
100 125
T
A
− Free-Air Temperature − °C
Figure 24
†
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
17
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC3702
DUAL MICROPOWER LinCMOS™ VOLTAGE COMPARATORS
SLCS013E − NOVEMBER 1986 − REVISED MARCH 2012
APPLICATION INFORMATION
The inputs should always remain within the supply rails in order to avoid forward biasing the diodes in the
electrostatic discharge (ESD) protection structure. If either input exceeds this range, the device is not damaged
as long as the input is limited to less than 5 mA. To maintain the expected output state, the inputs must remain
within the common-mode range. For example, at 25°C with V
−0.2 V and 4 V to ensure proper device operation.
= 5 V, both inputs must remain between
DD
To ensure reliable operation, the supply should be decoupled with a capacitor (0.1 μF) that is positioned as close
to the device as possible.
The TLC3702 has internal ESD-protection circuits that prevent functional failures at voltages up to 2000 V as
tested under MIL-STD-883C, Method 3015.2; however, care should be exercised in handling these devices as
exposure to ESD may result in the degradation of the device parametric performance.
Table of Applications
FIGURE
Pulse-width-modulated motor speed controller
Enhanced supply supervisor
25
26
27
28
Two-phase nonoverlapping clock generator
Micropower switching regulator
12 V
SN75603
Half-H Driver
DIR
EN
5 V
1/2 TLC3702
+
See
Note A
100 kΩ
+
10 kΩ
−
5 V
Motor
10 kΩ
C1
−
1/2 TLC3704
0.01 μF
12 V
(see Note B)
SN75604
Half-H Driver
DIR
EN
10 kΩ
5 V
10 kΩ
Motor Speed Control
Potentiometer
5 V
Direction
Control
S1
SPDT
NOTES: A. The recommended minimum capacitance is 10 μF to eliminate common ground switching noise.
B. Adjust C1 for change in oscillator frequency.
Figure 25. Pulse-Width-Modulated Motor Speed Controller
18
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC3702
DUAL MICROPOWER LinCMOS™ VOLTAGE COMPARATORS
SLCS013E − NOVEMBER 1986 − REVISED MARCH 2012
APPLICATION INFORMATION
5 V
5 V
V
SENSE
CC
12 V
1/2 TLC3702
3.3 kΩ
10 kΩ
To μP
12-V
Sense
+
TL7705A
Reset
RESIN
REF
RESET
GND
1 kΩ
−
C
T
2.5 V
1 μF
C
T
(see Note B)
1/2 TLC3702
+
To μP Interrupt
Early Power Fail
R1
V
(UNREG)
−
(see Note A)
R2
Monitors 5 VDC Rail
Monitors 12 VDC Rail
Early Power Fail Warning
(R1 +R2)
R2
NOTES: A.
V(UNREG) + 2.5
B. The value of C determines the time delay of reset.
T
Figure 26. Enhanced Supply Supervisor
19
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC3702
DUAL MICROPOWER LinCMOS™ VOLTAGE COMPARATORS
SLCS013E − NOVEMBER 1986 − REVISED MARCH 2012
APPLICATION INFORMATION
12 V
R1
12 V
100 kΩ
12 V
(see Note B)
1/2 TLC3702
−
1OUT
2OUT
R2
5 kΩ
+
1/2 TLC3702
100 kΩ
(see Note C)
−
+
1/2 TLC3702
−
22 kΩ
C1
0.01 μF
(see Note A)
+
100 kΩ
100 kΩ
R3
100 kΩ
(see Note B)
12 V
1OUT
2OUT
NOTES: A. Adjust C1 for a change in oscillator frequency where:
1/f = 1.85(100 kΩ)C1
B. Adjust R1 and R3 to change duty cycle
C. Adjust R2 to change deadtime
Figure 27. Two-Phase Nonoverlapping Clock Generator
20
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC3702
DUAL MICROPOWER LinCMOS™ VOLTAGE COMPARATORS
SLCS013E − NOVEMBER 1986 − REVISED MARCH 2012
APPLICATION INFORMATION
V
I
+ 6 V to 16 V
I
+ 0.01 mA to 0.25 mA
L
(R1 ) R2)
V
+ 2.5
O
R2
1/2 TLC3702
V
SK9504
(see Note C)
I
1/2 TLC3702
+
100 kΩ
G
S
V
−
I
100 kΩ
+
47 μF
V
−
I
Tantalum
D
100 kΩ
+
C1
IN5818
180 μF
(see Note A)
100 kΩ
R = 6 Ω
L = 1 mH
(see Note D)
R1
V
O
100 kΩ
TLC271
(see Note B)
V
I
R
L
470 μF
+
R2
100 kΩ
−
C2
100 pF
100 kΩ
270 kΩ
V
I
LM385
2.5 V
NOTES: A. Adjust C1 for a change in oscillator frequency
B. TLC271 − Tie pin 8 to pin 7 for low bias operation
C. SK9504 − VDS = 40 V
IDS = 1 A
D. To achieve microampere current drive, the inductance of the circuit must be increased.
Figure 28. Micropower Switching Regulator
21
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
PACKAGE OPTION ADDENDUM
www.ti.com
25-Sep-2013
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
5962-9153201Q2A
ACTIVE
LCCC
FK
20
1
TBD
POST-PLATE
N / A for Pkg Type
-55 to 125
5962-
9153201Q2A
TLC3702
MFKB
5962-9153201QHA
5962-9153202Q2A
5962-9153202QPA
TLC3702CD
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
CDIP
LCCC
CDIP
SOIC
SOIC
SOIC
SOIC
PDIP
PDIP
JG
FK
JG
D
8
20
8
1
1
TBD
TBD
TBD
A42
N / A for Pkg Type
N / A for Pkg Type
N / A for Pkg Type
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
N / A for Pkg Type
N / A for Pkg Type
-55 to 125
-55 to 125
-55 to 125
0 to 70
9153201QPA
TLC3702M
POST-PLATE
A42
5962-
9153202Q2A
1
5962-
9153202QPA
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
3702C
TLC3702CDG4
TLC3702CDR
D
8
75
Green (RoHS
& no Sb/Br)
0 to 70
3702C
D
8
2500
2500
50
Green (RoHS
& no Sb/Br)
0 to 70
3702C
TLC3702CDRG4
TLC3702CP
D
8
Green (RoHS
& no Sb/Br)
0 to 70
3702C
P
8
Pb-Free
(RoHS)
0 to 70
TLC3702CP
TLC3702CP
TLC3702CPE4
P
8
50
Pb-Free
(RoHS)
0 to 70
TLC3702CPSLE
TLC3702CPSR
OBSOLETE
ACTIVE
SO
SO
PS
PS
8
8
TBD
Call TI
Call TI
0 to 70
0 to 70
2000
2000
150
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
P3702
P3702
P3702
P3702
TLC3702CPSRG4
TLC3702CPW
ACTIVE
ACTIVE
ACTIVE
SO
PS
PW
PW
8
8
8
Green (RoHS
& no Sb/Br)
CU NIPDAU
CU NIPDAU
CU NIPDAU
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
0 to 70
0 to 70
0 to 70
TSSOP
TSSOP
Green (RoHS
& no Sb/Br)
TLC3702CPWG4
150
Green (RoHS
& no Sb/Br)
TLC3702CPWLE
TLC3702CPWR
OBSOLETE
ACTIVE
TSSOP
TSSOP
PW
PW
8
8
TBD
Call TI
Call TI
0 to 70
0 to 70
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
P3702
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
25-Sep-2013
Orderable Device
Status Package Type Package Pins Package
Eco Plan Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
0 to 70
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
TLC3702CPWRG4
TLC3702ID
ACTIVE
TSSOP
SOIC
PW
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
POST-PLATE
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
N / A for Pkg Type
P3702
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
D
D
75
75
Green (RoHS
& no Sb/Br)
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-55 to 125
-55 to 125
-55 to 125
-55 to 125
-55 to 125
3702I
TLC3702IDG4
TLC3702IDR
SOIC
Green (RoHS
& no Sb/Br)
3702I
SOIC
D
2500
2500
50
Green (RoHS
& no Sb/Br)
3702I
TLC3702IDRG4
TLC3702IP
SOIC
D
Green (RoHS
& no Sb/Br)
3702I
PDIP
P
Pb-Free
(RoHS)
TLC3702IP
TLC3702IP
P3702I
P3702I
P3702I
P3702I
3702M
3702M
3702M
3702M
TLC3702IPE4
TLC3702IPW
PDIP
P
50
Pb-Free
(RoHS)
N / A for Pkg Type
TSSOP
TSSOP
TSSOP
TSSOP
SOIC
PW
PW
PW
PW
D
150
150
2000
2000
75
Green (RoHS
& no Sb/Br)
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
N / A for Pkg Type
TLC3702IPWG4
TLC3702IPWR
TLC3702IPWRG4
TLC3702MD
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
TLC3702MDG4
TLC3702MDR
TLC3702MDRG4
TLC3702MFKB
SOIC
D
75
Green (RoHS
& no Sb/Br)
SOIC
D
2500
2500
1
Green (RoHS
& no Sb/Br)
SOIC
D
Green (RoHS
& no Sb/Br)
LCCC
FK
TBD
5962-
9153201Q2A
TLC3702
MFKB
TLC3702MJG
ACTIVE
CDIP
JG
8
1
TBD
A42
N / A for Pkg Type
-55 to 125
TLC3702MJG
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
25-Sep-2013
Orderable Device
TLC3702MJGB
Status Package Type Package Pins Package
Eco Plan Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
ACTIVE
CDIP
JG
8
1
TBD
A42
N / A for Pkg Type
-55 to 125
9153201QPA
TLC3702M
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TLC3702, TLC3702M :
Catalog: TLC3702
•
Addendum-Page 3
PACKAGE OPTION ADDENDUM
www.ti.com
25-Sep-2013
Automotive: TLC3702-Q1, TLC3702-Q1
•
Enhanced Product: TLC3702-EP, TLC3702-EP
•
Military: TLC3702M
•
NOTE: Qualified Version Definitions:
Catalog - TI's standard catalog product
•
Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
•
Enhanced Product - Supports Defense, Aerospace and Medical Applications
•
Military - QML certified for Military and Defense Applications
•
Addendum-Page 4
PACKAGE MATERIALS INFORMATION
www.ti.com
8-Jul-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TLC3702CDR
TLC3702CPSR
TLC3702IDR
SOIC
SO
D
PS
D
8
8
8
8
8
8
2500
2000
2500
2000
2500
2500
330.0
330.0
330.0
330.0
330.0
330.0
12.4
16.4
12.4
12.4
12.4
12.4
6.4
8.2
6.4
7.0
6.4
6.4
5.2
6.6
5.2
3.6
5.2
5.2
2.1
2.5
2.1
1.6
2.1
2.1
8.0
12.0
8.0
8.0
8.0
8.0
12.0
16.0
12.0
12.0
12.0
12.0
Q1
Q1
Q1
Q1
Q1
Q1
SOIC
TSSOP
SOIC
SOIC
TLC3702IPWR
TLC3702MDR
TLC3702MDRG4
PW
D
D
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
8-Jul-2013
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TLC3702CDR
TLC3702CPSR
TLC3702IDR
SOIC
SO
D
PS
D
8
8
8
8
8
8
2500
2000
2500
2000
2500
2500
340.5
367.0
340.5
367.0
367.0
367.0
338.1
367.0
338.1
367.0
367.0
367.0
20.6
38.0
20.6
35.0
35.0
35.0
SOIC
TSSOP
SOIC
SOIC
TLC3702IPWR
TLC3702MDR
TLC3702MDRG4
PW
D
D
Pack Materials-Page 2
MECHANICAL DATA
MCER001A – JANUARY 1995 – REVISED JANUARY 1997
JG (R-GDIP-T8)
CERAMIC DUAL-IN-LINE
0.400 (10,16)
0.355 (9,00)
8
5
0.280 (7,11)
0.245 (6,22)
1
4
0.065 (1,65)
0.045 (1,14)
0.310 (7,87)
0.290 (7,37)
0.063 (1,60)
0.015 (0,38)
0.020 (0,51) MIN
0.200 (5,08) MAX
0.130 (3,30) MIN
Seating Plane
0.023 (0,58)
0.015 (0,38)
0°–15°
0.100 (2,54)
0.014 (0,36)
0.008 (0,20)
4040107/C 08/96
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a ceramic lid using glass frit.
D. Index point is provided on cap for terminal identification.
E. Falls within MIL STD 1835 GDIP1-T8
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
相关型号:
5962-9153301MRA
IC DUAL SWITCHED CAPACITOR FILTER, RESISTOR PROGRAMMABLE, UNIVERSAL, CDIP20, Active Filter
WEDC
5962-9153401M2X
Buffer Amplifier, 1 Func, BIPolar, 0.358 X 0.358 INCH, 0.100 INCH HEIGHT, LCC-20
WEDC
5962-9153401MPX
IC BUFFER AMPLIFIER, DIP8, 0.405 X 0.310 INCH, 0.200 INCH HEIGHT, DIP-8, Buffer Amplifier
WEDC
5962-9153402MPX
Buffer Amplifier, 1 Func, BIPolar, 0.405 X 0.310 INCH, 0.200 INCH HEIGHT, DIP-8
WEDC
©2020 ICPDF网 联系我们和版权申明