ADC08B3000CIYB/NOPB [TI]
缓冲区容量为 4K 的 8 位、3.0GSPS 模数转换器 (ADC) | NNB | 128 | -40 to 85;
| 型号： | ADC08B3000CIYB/NOPB |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | 缓冲区容量为 4K 的 8 位、3.0GSPS 模数转换器 (ADC) | NNB | 128 | -40 to 85 转换器 模数转换器 |
| 文件： | 总57页 (文件大小：1190K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
ADC08B3000
www.ti.com
SNAS331M –JUNE 2006–REVISED APRIL 2013
ADC08B3000 8-Bit, 3 GSPS, High Performance, Low Power A/D Converter with 4K Buffer
Check for Samples: ADC08B3000
1
FEATURES
DESCRIPTION
The ADC08B3000 is a single, low power, high
performance CMOS analog-to-digital converter that
digitizes signals to 8 bits resolution at sample rates
up to 3.4 Gigasamples Per Second, (Gsps).
Consuming a typical 1.6 Watts at 3 Gsps from a
single 1.9 Volt supply, this device is ensured to have
no missing codes over the full operating temperature
range. The unique folding and interpolating
architecture, the fully differential comparator design,
the innovative design of the internal sample-and-hold
amplifier and the calibration scheme enable an
excellent response of all dynamic parameters up to
Nyquist, producing a high 7.1 Effective Number Of
Bits, (ENOB), with a 748 MHz input signal and a 3
GHz sample rate while providing a 10-18 Code Error
Rate. A sample rate of 3 Gsps is achieved by
interleaving two ADCs, each operating at 1.5 Gsps.
Output formatting is offset binary. The device
contains a 4K Capture Buffer with output on two 8-bit
Low Voltage CMOS (LVCMOS) output buses at rates
up to 200MHz.
2
•
Single +1.9V ±0.1V Operation
•
•
•
•
Choice of SDR or DDR Output Clocking
Internal selectable 4K Data Buffer
Serial Interface for Extended Control
Adjustment of Input Full-Scale Range, Offset
and Clock Phase
•
•
Duty Cycle Corrected Sample Clock
Test Pattern Output Capability
APPLICATIONS
•
•
Distance Ranging
Test and Measurement
KEY SPECIFICATIONS
•
•
•
•
•
•
•
Resolution: 8 Bits
Max Conversion Rate: 3 Gsps (min)
Code Error Rate: 10-18 (typ)
ENOB @ 748 MHz Input: 7.1 Bits (typ)
SNR @ 748 MHz: 44.9 dB (typ)
Full Power Bandwidth: 3 GHz (typ)
Power Consumption
The converter typically consumes less than 25 mW in
the Power Down Mode and is available in a 128-lead,
thermally enhanced exposed pad HLQFP and
operates over the Industrial (-40°C ≤ TA ≤ +85°C)
temperature range.
–
–
Full Power Capure: 1.6 W (typ)
Power Down Mode: 25 mW (typ)
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2006–2013, Texas Instruments Incorporated
ADC08B3000
SNAS331M –JUNE 2006–REVISED APRIL 2013
www.ti.com
Block Diagram
+
S/H
8-BIT
ADC
-
RESET
OR
V +
IN
V
-
IN
D1 CMOS Data
DRDY1
8 bit
8 bit
4k Data
Capture
Buffer
+
-
S/H
D2 CMOS Data
DRDY2
8-BIT
ADC
V
REF
V
BG
RCLK
CalRun
CLK+
CLK-
CLK/2
2
Control
Inputs
ADC
Control
Logic
Capture Buffer
Control
Logic
Serial
Interface
3
FF WENSYNC
PD CAL
ADCCLK_RST
WEN REN EF
2
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: ADC08B3000
ADC08B3000
www.ti.com
SNAS331M –JUNE 2006–REVISED APRIL 2013
Pin Configuration
D1<7>
96
GND
1
2
3
4
5
6
7
8
V
A
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
D1<6>
D1<5>
D1<4>
D1<3>
D1<2>
D1<1>
D1<0>
SCLK
OutEdge/DDR/SDATA
V
A
GND
V
CMO
V
A
V
DR
GND
CLK+
CLK-
GND
9
DR GND
DRDY1
NC
NC
NC
RCLK
RESET
OR
WENSYNC
NC
10
11
12
V
A
13
14
15
16
17
18
19
20
FSR/ECE
ADCCLK_RST
V
A
V
A
ADC08B3000
V
V
+
-
IN
IN
V
NC
NC
DRDY2
DR GND
A
GND 21
22
23
24
25
26
27
28
29
30
31
32
ADCCLK_RST+
ADCCLK_RST-
GND
Exposed pad bottom side.
(See Note below.)
V
DR
V
A
D2<0>
D2<1>
D2<2>
D2<3>
D2<4>
D2<5>
D2<6>
D2<7>
PD
GND
V
A
NC
CAL
V
BG
R
EXT
Note: The exposed pad on the bottom of the package must be soldered to a ground plane to ensure rated
performance.
Figure 1. HLQFP Package
See Package Number NNB0128A
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: ADC08B3000
ADC08B3000
SNAS331M –JUNE 2006–REVISED APRIL 2013
www.ti.com
Pin Descriptions and Equivalent Circuits
Pin Functions
Pin No.
Symbol
Equivalent Circuit
Description
V
A
Serial Interface Clock
50k
(Input): LVCMOS - When the extended control mode is
enabled, this pin functions as the SCLK input which clocks in
the serial data. See NORMAL/EXTENDED CONTROL for
details on the extended control mode. See THE SERIAL
INTERFACE for description of the serial interface. Ground
this pin when the ADC is not in extended control mode.
3
SCLK
GND
V
A
Edge Select / Double Data Rate / Serial Data
50k
(Input): LVCMOS - When this input is low or high, it sets the
edge of DRDY at which the output data transitions. (See
OutEdge Setting). When this pin is floating or connected to
1/2 the supply voltage, DDR clocking is enabled. When the
extended control mode is enabled, this pin functions as the
SDATA input. See NORMAL/EXTENDED CONTROL for
details on the extended control mode. See THE SERIAL
INTERFACE for description of the serial interface.
200k
DDR
50k
8 pF
OutEdge / DDR /
SDATA
4
GND
SDATA
V
A
ADC Sample Clock Reset
(Input): LVCMOS - A positive pulse on this pin is used to
reset and synchronize the ADC08B3000 with other
ADC08B3000s in the system. See MULTIPLE ADC
SYNCHRONIZATION. When bit 14 in the Configuration
Register (address 1h) is set to 0b, this single-ended
ADCCLK_RST pin is selected. See description of pins 22,
23.
15
ADCCLK_RST
V
A
Power Down
(Input): LVCMOS - A logic high on the PD pin puts the
device, except for the Capture Buffer, into the Power Down
Mode.
26
30
PD
Calibration Cycle Initiate
GND
(Input): LVCMOS - A minimum 80 input clock cycles logic
low followed by a minimum of 80 input clock cycles high on
this pin initiates the self calibration sequence. See
Calibration for an overview of calibration and On-Command
Calibration for a description of on-command calibration.
CAL
V
A
Full Scale Range Select / Extended Control Enable
(Input): LVCMOS - In the Normal (Non-Extended) Control
Mode, a logic low on this pin sets the full-scale differential
input range to 600 mVP-P. A logic high on this pin sets the
full-scale differential input range to 810 mVP-P. See The
Analog Inputs. To enable the extended control mode,
whereby the serial interface and control registers are
employed, allow this pin to float or connect it to a voltage
equal to VA/2. See NORMAL/EXTENDED CONTROL for
information on the extended control mode.
50k
50k
200k
14
FSR/ECE
8 pF
GND
V
A
Calibration Delay / Serial Interface Chip Select
(Input): LVCMOS - With a logic high or low on pin 14, this
pin functions as Calibration Delay and sets the number of
input clock cycles after power up before calibration begins
(See Calibration). With pin 14 floating, this pin acts as the
chip select pin for the serial interface input and the CalDly
value becomes "0" (short delay with no provision for a long
power-up calibration delay).
50k
50k
127
CalDly / SCS
GND
4
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: ADC08B3000
ADC08B3000
www.ti.com
Pin No.
SNAS331M –JUNE 2006–REVISED APRIL 2013
Pin Descriptions and Equivalent Circuits (continued)
Pin Functions
Equivalent Circuit
Symbol
Description
V
A
Sample Clock Input
(Input): LVDS - The differential clock signal must be a.c.
coupled to these pins. The input signal is sampled on both
the rising and falling edge of CLK. See Acquiring the Input
for a description of acquiring the input, Clocking and THE
SAMPLE CLOCK INPUT for an overview of the clock inputs.
50k
50k
AGND
10
11
CLK+
CLK-
100
V
BIAS
V
A
AGND
V
A
50k
Signal Input
AGND
100
V
CMO
(Input): Analog - Analog Signal Input that must be applied
differentially. The differential full-scale input is defined by
pin 14 in the Normal mode and by the Full-Scale Voltage
Adjust register in the Extended Control mode. See
REGISTER DESCRIPTION.
18
19
VIN
+
Control from V
CMO
VIN−
V
A
50k
AGND
V
A
Sample Clock Reset
(Input): LVDS - A positive differential pulse on these pins is
used to reset and synchronize the ADC sample clock when
multiple ADCs are used. See MULTIPLE ADC
SYNCHRONIZATION. When bit 14 in the Configuration
Register (address 1h) is set to 1b, these differential
ADCCLK_RST± pins are selected. See description for
pin 15.
AGND
22
23
ADCCLK_RST+
ADCCLK_RST-
100
V
A
AGND
V
CMO
V
A
Common Mode Voltage
(Output): ANALOG - The voltage output at this pin is
required to be the common mode input voltage at VIN+ and
VIN− when d.c. coupling is used. This pin should be
grounded when a.c. coupling is used at the analog input.
This pin is capable of sourcing or sinking 100μA and can
drive a load up to 80 pF. See THE ANALOG INPUT.
AC
Couple
Enable
200k
8 pF
7
VCMO
GND
Bandgap Output Voltage
31
VBG
(Output): Analog - Capable of 100 μA source/sink and can
drive a load up to 80 pF.
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: ADC08B3000
ADC08B3000
SNAS331M –JUNE 2006–REVISED APRIL 2013
www.ti.com
Pin Descriptions and Equivalent Circuits (continued)
Pin Functions
Equivalent Circuit
Pin No.
Symbol
Description
V
D
Calibration Running
126
CalRun
(Output): LVCMOS - This pin is at a logic high while a
calibration is running.
DGND
V
A
V
External Bias Resistor Connection
Analog - Nominal value is 3.3k-Ohms (±0.1%) to ground.
See Calibration.
32
REXT
GND
Temperature Diode
Tdiode_P
Tdiode_N
Analog - Positive (Anode) and Negative (Cathode). These
pins may be used for die temperature measurements,
however no specified accuracy is implied or ensured. See
Thermal Management.
34
35
Tdiode_P
Tdiode_N
Digital Data Output 2
72
71
70
69
68
67
66
65
D2<0>
D2<1>
D2<2>
D2<3>
D2<4>
D2<5>
D2<6>
D2<7>
(Output): LVCMOS - When the REN input is asserted and
Two Port Enable, (TPE) is set to 1b in the Capture Buffer
register (addr: Fh, bit: 12), half of the data is read from the
capture buffer and presented at this port synchronous with
each rising edge of Read CLK (RCLK). The data on this port
is the earlier sample data vs. the Digital Data Output 1 data.
When Two Port Enable is set to 0b in the Capture Buffer
register, data output 2 is high-impedance.
Data Ready 2
(Output): LVCMOS - DRDY is generated by RCLK and is
synchronized to the output data. The use of this pin assists
in eliminating the latency uncertainty between when Read
CLK (RCLK) transitions and when data transitions at the
output.
V
75
DRDY2
D
Digital Data Output 1
(Output): LVCMOS - When the REN input is asserted, data
is read from the capture buffer and presented at this port
synchronous with each rising edge of Read CLK (RCLK).
When the Two Port Enable bit (TPE) is set to 1b in the
Capture Buffer register (addr: Fh, bit: 12), half of the data is
presented at this port. The data on this port is the later
sample data vs. the Digital Data Output 2 data. When REN
is deasserted, this output holds the data from the previous
read. When Two Port Enable is set to 0b in the Capture
Buffer register, this port presents all of the data from the
Capture Buffer.
89
90
91
92
93
94
95
96
D1<0>
D1<1>
D1<2>
D1<3>
D1<4>
D1<5>
D1<6>
D1<7>
DGND
Data Ready 1
(Output): LVCMOS - DRDY is generated by RCLK and is
synchronized to the output data. The use of this pin assists
in eliminating the latency uncertainty between when Read
CLK (RCLK) transitions and when data transitions at the
output.
86
DRDY1
6
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: ADC08B3000
ADC08B3000
www.ti.com
SNAS331M –JUNE 2006–REVISED APRIL 2013
Pin Descriptions and Equivalent Circuits (continued)
Pin Functions
Equivalent Circuit
Pin No.
Symbol
Description
Read Enable
(Input): LVCMOS - A logic high on this input causes a byte
of data to be read from the Capture Buffer with each RCLK
cycle. This signal must not be asserted while the WEN is
already asserted. See Coordinating Read Enable (REN) and
Write Enable (WEN).
45
REN
V
A
Write Enable
(Input): LVCMOS - A logic high on this input causes a byte
of data to be written into the Capture Buffer with each
sample clock cycle. This signal may be asserted
asynchronously as it is internally synchronized with the
internal sample clock.
46
82
WEN
Read Clock
(Input): LVCMOS - Free running clock that is used to read
data from the Capture Buffer. The parallel data at the output
port and the EF flag are asserted synchronous with this
clock.
GND
RCLK
Reset
81
79
RESET
(Input): LVCMOS - A logic high at this input resets all
Capture Buffer control logic in the chip.
Synchronized WEN
(Output): LVCMOS - The control input WEN is synchronized
on-chip with the internal Sample Clock and is provided at this
output.
WENSYNC
Out Of Range
(Output): LVCMOS - A logic high on this pin indicates that
the differential input is out of the linear range. This signal is
asserted if the input signal has gone out of range at any time
during the data capture operation. This pin is cleared after
the Capture Buffer is read or after asserting the RESET pin.
80
OR
FF
V
D
Buffer Full Flag
(Output): LVCMOS - This signal is asserted synchronous
with the clock when the capture buffer is full. If the WEN
input remains asserted, the next CLK will cause an overflow,
whereby the pointer will wrap around and begin overwriting
the old data if the Auto Stop Write (ASW) bit is set to 0b in
the Capture Buffer Control register. This signal is deasserted
when a read cycle is initiated or a RESET is issued because
the data buffer is no longer "full".
115
116
DGND
Buffer Empty Flag
(Output): LVCMOS - This signal is asserted synchronous
with the RCLK signal when the Capture Buffer is empty. It is
deasserted when a write cycle is initiated and the data buffer
is no longer "empty".
EF
VA
2, 5, 8, 13,
16, 17, 20,
25, 28, 33,
128
Analog power supply pins
(Power) - Bypass these pins to ground.
40, 51, 62,
73, 88, 99,
110, 121
Output Driver power supply pins
(Power) - Bypass these pins to DR GND.
VDR
GND
1, 6, 9, 12,
21, 24, 27
(Gnd) - Ground return for VA.
42, 53, 64,
74, 87, 97,
108, 119
DR GND
(Gnd) - Ground return for VDR.
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: ADC08B3000
ADC08B3000
SNAS331M –JUNE 2006–REVISED APRIL 2013
www.ti.com
Pin Descriptions and Equivalent Circuits (continued)
Pin Functions
Equivalent Circuit
Pin No.
Symbol
Description
29, 36, 37,
38, 39, 41,
43, 44, 47,
48, 49, 50,
52, 54, 55,
56, 57, 58,
59, 60, 61,
63, 76, 77,
78, 83, 84,
85, 98,
NC
No Connection Make no connection to these pins.
100, 101,
102, 103,
104, 105,
106, 107,
109, 111,
112, 113,
114, 117,
118, 120,
122, 123,
124, 125
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings(1)(2)(3)
Analog Supply Voltage (VA)
2.2V
VDR
0V to (VA + 300mV)
Voltage on Any Input Pin
(Except VIN+, VIN-)
−0.15V to (VA + 0.15V)
Voltage on VIN+, VIN
-
(Maintaining Common Mode)
-0.15V to 2.5V
Ground Difference
(|GND - DR GND|)
Input Current at Any Pin(4)
Package Input Current(4)
0V to 100 mV
±25 mA
±50 mA
Power Dissipation at TA ≤ 85°C
2.3 W
Human Body Model
Machine Model
2500V
ESD Susceptibility(5)
Storage Temperature
250V
−65°C to +150°C
(1) All voltages are measured with respect to GND = DR GND = 0V, unless otherwise specified.
(2) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. There is no specification of operation at the
Absolute Maximum Ratings. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific
performance limits. For ensured specifications and test conditions, see Converter Electrical Characteristics. The ensured specifications
apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed
test conditions.
(3) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
(4) When the input voltage at any pin exceeds the power supply limits (that is, less than GND or greater than VA), the current at that pin
should be limited to 25 mA. The 50 mA maximum package input current rating limits the number of pins that can safely exceed the
power supplies with an input current of 25 mA to two. This limit is not placed upon the power and ground pins.
(5) Human body model is 100 pF capacitor discharged through a 1.5 kΩ resistor. Machine model is 220 pF discharged through ZERO
Ohms.
8
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: ADC08B3000
ADC08B3000
www.ti.com
SNAS331M –JUNE 2006–REVISED APRIL 2013
Operating Ratings(1)(2)
Ambient Temperature Range
Supply Voltage (VA)
−40°C ≤ TA ≤ +85°C
+1.8V to +2.0V
+1.8V to VA
Driver Supply Voltage (VDR
)
Analog Input Common Mode Voltage
VCMO ±50mV
0V to 2.15V
(100% duty cycle)
0V to 2.5V
VIN+, VIN- Voltage Range (Maintaining Common Mode)
(10% duty cycle)
Ground Difference
(|GND - DR GND|)
0V
0V to VA
CLK Pins Voltage Range
Differential CLK Amplitude
0.4VP-P to 2.0VP-P
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. There is no specification of operation at the
Absolute Maximum Ratings. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific
performance limits. For ensured specifications and test conditions, see Converter Electrical Characteristics. The ensured specifications
apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed
test conditions.
(2) All voltages are measured with respect to GND = DR GND = 0V, unless otherwise specified.
Package Thermal Resistance(1)(2)
Package
θJA
θJC (Top of Package)
θJ-PAD (Thermal Pad)
128-Lead Exposed Pad
HLQFP
26°C / W
10°C / W
2.8°C / W
(1) Soldering process must comply with Reflow Temperature Profile specifications. Refer to www.ti.com/packaging.
(2) Reflow temperature profiles are different for lead-free and non-lead-free packages.
Converter Electrical Characteristics(1)(2)
The following specifications apply after calibration for VA = VDR = 1.9V, VIN FSR (a.c. coupled) = differential 810mVP-P
,
CL = 10 pF, Differential a.c. coupled sine wave Input Clock, fCLK = 1.5 GHz at 0.4VP-P with 50% duty cycle, Duty Cycle
Stabilizer enabled, RCLK = 100 MHz, VBG = Floating, Non-Extended Control Mode, SDR Mode, REXT = 3300Ω ±0.1%, Analog
Signal Source Impedance = 100Ω Differential, after calibration. Boldface limits apply for TA = TMIN to TMAX. All other limits
TA = 25°C, unless otherwise noted.
Units
(Limits)
Parameter
Test Conditions
Typical(3)
Limits(3)
STATIC CONVERTER CHARACTERISTICS
DC Coupled, 1MHz Sine Wave
Over Ranged
INL
Integral Non-Linearity (Best fit)
Differential Non-Linearity
±0.35
±0.20
±0.9
LSB (max)
LSB (max)
DC Coupled, 1MHz Sine Wave
Over Ranged
DNL
±0.6
8
Resolution with No Missing Codes
Offset Error
Bits
LSB
VOFF
-0.10
±45
VOFF_ADJ Input Offset Adjustment Range
Extended Control Mode
Extended Control Mode
mV
PFSE
Positive Full-Scale Error(4)
Negative Full-Scale Error(4)
Full-Scale Adjustment Range
−2.7
−1.6
±20
±25
±25
±15
mV (max)
mV (max)
%FS
NFSE
FS_ADJ
DYNAMIC CONVERTER CHARACTERISTICS
FPBW Full Power Bandwidth
3
GHz
(1) The analog inputs are protected as shown below. Input voltage magnitudes beyond the Absolute Maximum Ratings may damage this
device. See Figure 2
(2) To ensure accuracy, it is required that VA and VDR be well bypassed. Each supply pin must be decoupled with separate bypass
capacitors. Additionally, achieving rated performance requires that the backside exposed pad be well grounded.
(3) Typical figures are at TA = 25°C, and represent most likely parametric norms. Test limits are ensured to AOQL (Average Outgoing
Quality Level).
(4) Calculation of Full-Scale Error for this device assumes that the actual reference voltage is exactly its nominal value. Full-Scale Error for
this device, therefore, is a combination of Full-Scale Error and Reference Voltage Error. See Figure 3. For relationship between Gain
Error and Full-Scale Error, see Specification Definitions for Gain Error.
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: ADC08B3000
ADC08B3000
SNAS331M –JUNE 2006–REVISED APRIL 2013
www.ti.com
Converter Electrical Characteristics(1)(2) (continued)
The following specifications apply after calibration for VA = VDR = 1.9V, VIN FSR (a.c. coupled) = differential 810mVP-P
,
CL = 10 pF, Differential a.c. coupled sine wave Input Clock, fCLK = 1.5 GHz at 0.4VP-P with 50% duty cycle, Duty Cycle
Stabilizer enabled, RCLK = 100 MHz, VBG = Floating, Non-Extended Control Mode, SDR Mode, REXT = 3300Ω ±0.1%, Analog
Signal Source Impedance = 100Ω Differential, after calibration. Boldface limits apply for TA = TMIN to TMAX. All other limits
TA = 25°C, unless otherwise noted.
Units
(Limits)
Parameter
Code Error Rate
Test Conditions
Typical(3)
Limits(3)
Errors/
Sample
10-18
50 to 950
7.2
Gain Flatness
0.0 to -1.0 dBFS
MHz
fIN = 373 MHz,
VIN = FSR − 0.5 dB
6.7
6.5
Bits (min)
fIN = 748 MHz,
VIN = FSR − 0.5 dB
ENOB
SINAD
SNR
Effective Number of Bits
7.1
6.4
Bits (min)
Bits
fIN = 1498 MHz,
VIN = FSR − 0.5 dB
fIN = 373 MHz,
VIN = FSR − 0.5 dB
45.1
44.5
40.3
45.3
44.9
42.4
-57
41.8
41.0
dB (min)
dB (min)
dB
fIN = 748 MHz,
VIN = FSR − 0.5 dB
Signal-to-Noise Plus Distortion Ratio
fIN = 1498 MHz,
VIN = FSR − 0.5 dB
fIN = 373 MHz,
VIN = FSR − 0.5 dB
42.5
42
dB (min)
dB (min)
dB
fIN = 748 MHz,
VIN = FSR − 0.5 dB
Signal-to-Noise Ratio
fIN = 1498 MHz,
VIN = FSR − 0.5 dB
fIN = 373 MHz,
VIN = FSR − 0.5 dB
-50
-48
dB (max)
dB (max)
dB
fIN = 748 MHz,
VIN = FSR − 0.5 dB
THD
Total Harmonic Distortion
-54.8
-44.3
-68
fIN = 1498 MHz,
VIN = FSR − 0.5 dB
fIN = 373 MHz,
VIN = FSR − 0.5 dB
dB
fIN = 748 MHz,
VIN = FSR − 0.5 dB
2nd Harm Second Harmonic Distortion
-65
dB
fIN = 1498 MHz,
VIN = FSR − 0.5 dB
-45
dB
fIN = 373 MHz,
VIN = FSR − 0.5 dB
-63
dB
fIN = 748 MHz,
VIN = FSR − 0.5 dB
3rd Harm Third Harmonic Distortion
-57
dB
fIN = 1498 MHz,
VIN = FSR − 0.5 dB
-51
dB
fIN = 373 MHz,
VIN = FSR − 0.5 dB
55.4
54.0
45.3
47
dB (min)
dB (min)
dB
fIN = 748 MHz,
VIN = FSR − 0.5 dB
SFDR
IMD
Spurious-Free dynamic Range
Intermodulation Distortion
46.5
fIN = 1498 MHz,
VIN = FSR − 0.5 dB
fIN1 = 749.084 MHz,
VIN = FSR − 7 dB
fIN2 = 756.042 MHz,
VIN = FSR − 7 dB
-52
dBFS
10
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: ADC08B3000
ADC08B3000
www.ti.com
SNAS331M –JUNE 2006–REVISED APRIL 2013
Converter Electrical Characteristics(1)(2) (continued)
The following specifications apply after calibration for VA = VDR = 1.9V, VIN FSR (a.c. coupled) = differential 810mVP-P
,
CL = 10 pF, Differential a.c. coupled sine wave Input Clock, fCLK = 1.5 GHz at 0.4VP-P with 50% duty cycle, Duty Cycle
Stabilizer enabled, RCLK = 100 MHz, VBG = Floating, Non-Extended Control Mode, SDR Mode, REXT = 3300Ω ±0.1%, Analog
Signal Source Impedance = 100Ω Differential, after calibration. Boldface limits apply for TA = TMIN to TMAX. All other limits
TA = 25°C, unless otherwise noted.
Units
(Limits)
Parameter
Test Conditions
Typical(3)
Limits(3)
ANALOG INPUT AND REFERENCE CHARACTERISTICS
mVP-P
(min)
550
650
740
880
FSR pin 14 Low
600
mVP-P
(max)
VIN
Full Scale Analog Differential Input Range
mVP-P
(min)
FSR pin 14 High
810
mVP-P
(max)
V
CMO − 50 mV (min)
VCMI
CIN
Analog Input Common Mode Voltage
Analog Input Capacitance(5)
VCMO
VCMO + 50 mV (max)
Differential
0.8
2.2
pF
pF
Each input pin to ground
95
103
Ω (min)
Ω (max)
RIN
Differential Input Resistance
100
ANALOG OUTPUT CHARACTERISTICS
VCMO Common Mode Output Voltage
0.95
1.45
V (min)
V (max)
ICMO = ±100 µA
1.26
VA = 1.8V
VA = 2.0V
0.60
0.66
V
V
VCMO_LVL VCMO input threshold to set DC Coupling mode
Common Mode Output Voltage Temperature
Coefficient
TC VCMO
TA = −40°C to +85°C
118
ppm/°C
pF
CLOAD
Maximum VCMO load Capacitance
VCMO
80
1.20
1.33
V (min)
V (max)
VBG
Bandgap Reference Output Voltage
IBG = ±100 µA
1.26
28
TA = −40°C to +85°C,
IBG = ±100 µA
TC VBG
Bandgap Reference Voltage Temperature Coefficient
ppm/°C
pF
CLOAD VBG Maximum Bandgap Reference load Capacitance
80
TEMPERATURE DIODE CHARACTERISTICS
192 µA vs. 12 µA,
TJ = 25°C
71.23
85.54
mV
mV
ΔVBE
Temperature Diode Voltage
192 µA vs. 12 µA,
TJ = 85°C
LVDS INPUT CHARACTERISTICS
0.4
0.7
VP-P (min)
VP-P (max)
Sine Wave Clock
0.5
0.5
VID
Differential Clock Input Level
0.4
0.7
VP-P (min)
VP-P (max)
Square Wave Clock
II
Input Current
VIN = 0 or VIN = VA
Differential
±1
0.02
1.5
µA
pF
pF
CIN
Input Capacitance(5)
Each input to ground
(5) The analog and clock input capacitances include packaging capacitance values of 0.7 pF differential and 1 pF each input pin to ground,
which are isolated from the die capacitance by lead and bond wire inductances.
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: ADC08B3000
ADC08B3000
SNAS331M –JUNE 2006–REVISED APRIL 2013
www.ti.com
Converter Electrical Characteristics(1)(2) (continued)
The following specifications apply after calibration for VA = VDR = 1.9V, VIN FSR (a.c. coupled) = differential 810mVP-P
,
CL = 10 pF, Differential a.c. coupled sine wave Input Clock, fCLK = 1.5 GHz at 0.4VP-P with 50% duty cycle, Duty Cycle
Stabilizer enabled, RCLK = 100 MHz, VBG = Floating, Non-Extended Control Mode, SDR Mode, REXT = 3300Ω ±0.1%, Analog
Signal Source Impedance = 100Ω Differential, after calibration. Boldface limits apply for TA = TMIN to TMAX. All other limits
TA = 25°C, unless otherwise noted.
Units
(Limits)
Parameter
Test Conditions
Typical(3)
Limits(3)
LVCMOS INPUT CHARACTERISTICS
ADCCLK_RST, PD, CAL
OutEdge, FSR, CalDly
All LVCMOS Inputs
0.69 x VA
0.79 x VA
0.28 x VA
V (min)
V (min)
V (max)
VIH
VIL
Logic High Input Voltage
Logic Low Input Voltage
ADCCLK_RST, CAL, PD,
CalDly
1
30
1
µA
µA
µA
IIH
Logic High Input Current
FSR/ECE
ADCCLK_RST, CAL, PD,
CalDly
IIL
Logic Low Input Current
Input Capacitance(6)
FSR/ECE
30
µA
pF
CIN
Each input to ground
1.2
LVCMOS OUTPUT CHARACTERISTICS
VOH
VOL
CMOS High level output
CMOS Low level output
IOH = -400uA
IOH = 400uA
1.65
0.15
1.5
0.3
V (min)
V (max)
POWER SUPPLY CHARACTERISTICS
Full Power Capture Mode
WEN = High,
REN =PD = Low
723
2.4
800
180
1.9
mA (max)
mA
IA
Analog Supply Current
Output Driver Supply Current
Power Consumption
Power Down Mode
WEN = Low,
REN = PD = High
Full Power Capture Mode
WEN = High,
REN =PD = Low
135
10.8
1.6
mA (max)
mA
IDR
Power Down Mode
WEN = Low,
REN = PD = High
Full Power Capture Mode
WEN = High,
REN =PD = Low
W (max)
mW
PD
Power Down Mode
WEN = Low,
25
REN = PD = High
Change in Offset Error with
change in VA from 1.8V to 2.0V
PSRR1
PSRR2
D.C. Power Supply Rejection Ratio
A.C. Power Supply Rejection Ratio
70
50
dB
dB
248 MHz, 100mVP-P riding on
VA
(6) The digital control pin capacitances are die capacitances only. Additional package capacitance of 1.6 pF each pin to ground are isolated
from the die capacitances by lead and bond wire inductances.
12
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: ADC08B3000
ADC08B3000
www.ti.com
SNAS331M –JUNE 2006–REVISED APRIL 2013
Converter Electrical Characteristics(1)(2) (continued)
The following specifications apply after calibration for VA = VDR = 1.9V, VIN FSR (a.c. coupled) = differential 810mVP-P
,
CL = 10 pF, Differential a.c. coupled sine wave Input Clock, fCLK = 1.5 GHz at 0.4VP-P with 50% duty cycle, Duty Cycle
Stabilizer enabled, RCLK = 100 MHz, VBG = Floating, Non-Extended Control Mode, SDR Mode, REXT = 3300Ω ±0.1%, Analog
Signal Source Impedance = 100Ω Differential, after calibration. Boldface limits apply for TA = TMIN to TMAX. All other limits
TA = 25°C, unless otherwise noted.
Units
(Limits)
Parameter
Test Conditions
Typical(3)
Limits(3)
AC ELECTRICAL CHARACTERISTICS - Sample Clock
fCLK1
fCLK2
Maximum Input Clock Frequency
Minimum Input Clock Frequency
Sample rate is 2x clock input
Sample rate is 2x clock input
1.5
GHz (min)
MHz
500
50
500MHz ≤ Input clock frequency
≤ 1.5 GHz(7)
20
80
% (min)
% (max)
tCYC
Input Clock Duty Cycle
tLC
Input Clock Low Time
Input Clock High Time
See(8)
See(8)
333
333
133
133
ps (min)
ps (min)
tHC
Input CLK transition to
Acquisition of Data
tAD
tAJ
Sample (Aperture) Delay
Aperture Jitter
1.4
ns
0.55
ps rms
AC ELECTRICAL CHARACTERISTICS - Capture Buffer Signals
fRCLK
tLHT
Maximum Capture Buffer Read Clock Frequency
Low to High Transition Time
200
250
250
MHz
ps
10% to 90%
10% to 90%
tHLT
High to Low Transition Time
ps
Delay after 3 Write Clock
Cycles
tDWS1
tDWS2
tHWEN
Delay WENSYNC
7.0
-1.3
-5.0
ns
ns
Delay WENSYNC
Delay after FF assertion
Hold Time after WENSYNC
deassertion
Minimum Hold Time WEN
0
1
ns (min)
RCLK cycle delay after
deassertion of REN
RCLK
Cyc. (min)
TASWEN
Minimum Assertion Delay WEN
Delay Full Flag
0
Delay after REN assertion,
RCLK = 100 MHz
7.3
5.0
ns
ns
tDFF
Delay after REN assertion,
RCLK = 200 MHz
Delay after last DRDY pulse,
RCLK = 200 MHz
tDEF1
tDEF2
tDEF3
Delay Empty Flag
Delay Empty Flag
Delay Empty Flag
0
ns
ns
ns
Delay after RESET
2.0
9.5
Delay after WENSYNC
assertion
Setup Time before rising edge
of RCLK
tSREN
Minimum Setup Time REN
Minimum Hold Time REN
0.2
-5
0.3
0
ns (min)
ns (min)
Hold Time after last DRDY
pulse or positive edge of
RESET
tHREN
1.8
4.0
ns (min)
ns (max)
RCLK to DRDY Delay, RCLK =
100 MHz or 200 MHz
tDDRDY
Delay RCLK to DRDY
2.7
For SDR and
DDR 0º modes.
tSKEW
tSO
Skew DRDY to Data
0
5
5
±200
ps (max)
Data Output to DRDY
For DDR 90º mode
Setup Time Data Output
Hold Time Data Output
ns
ns
DRDY to Data Output
For DDR 90º mode
tHO
(7) This parameter is ensured by design and/or characterization and is not tested in production.
(8) This parameter is ensured by design and is not tested in production.
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: ADC08B3000
ADC08B3000
SNAS331M –JUNE 2006–REVISED APRIL 2013
www.ti.com
Converter Electrical Characteristics(1)(2) (continued)
The following specifications apply after calibration for VA = VDR = 1.9V, VIN FSR (a.c. coupled) = differential 810mVP-P
,
CL = 10 pF, Differential a.c. coupled sine wave Input Clock, fCLK = 1.5 GHz at 0.4VP-P with 50% duty cycle, Duty Cycle
Stabilizer enabled, RCLK = 100 MHz, VBG = Floating, Non-Extended Control Mode, SDR Mode, REXT = 3300Ω ±0.1%, Analog
Signal Source Impedance = 100Ω Differential, after calibration. Boldface limits apply for TA = TMIN to TMAX. All other limits
TA = 25°C, unless otherwise noted.
Units
(Limits)
Parameter
Test Conditions
Typical(3)
Limits(3)
AC ELECTRICAL CHARACTERISTICS - Serial Interface
fSCLK
tSSU
tSH
Serial Clock Frequency
67
2.5
1
MHz
ns (min)
ns (min)
ns
Data to Serial Clock Rising Setup Time
Data to Serial Clock Rising Hold Time
CS to Serial Clock Rising Setup Time
CS to Serial Clock Falling Hold Time
Serial Clock Low Time
tSCS
tHCS
2.5
1.5
ns
6
6
ns (min)
ns (min)
Serial Clock High Time
AC ELECTRICAL CHARACTERISTICS - General Signals
tSR
tHR
Setup Time ADCCLK_RST±
Hold Time ADCCLK_RST±
Differential ADCCLK_RST
Differential ADCCLK_RST
90
30
ps
ps
CLK± Cyc.
(min)
tPWR
Pulse Width ADCCLK_RST±
See(9)
4
PD low to Rated Accuracy Conversion (Wake-Up
Time)
tWU
1
µs
tCAL
Calibration Cycle Time
1.4 x 105
CLK± Cyc.
CLK± Cyc.
(min)
tCAL_L
CAL Pin Low Time
See(9) and Figure 6
80
80
CLK± Cyc.
(min)
tCAL_H
CAL Pin High Time
See(9) and Figure 6
Calibration delay
CalDly = Low
CLK± Cyc.
(max)
See(9), Calibration and Figure 6
See(9), Calibration and Figure 6
225
231
tCalDly
Calibration delay
CalDly = High
CLK± Cyc.
(max)
(9) This parameter is ensured by design and is not tested in production.
V
A
TO INTERNAL
CIRCUITRY
I / O
GND
Figure 2.
14
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: ADC08B3000
ADC08B3000
www.ti.com
SNAS331M –JUNE 2006–REVISED APRIL 2013
SPECIFICATION DEFINITIONS
APERTURE (SAMPLING) DELAY is the amount of delay, measured from the sample edge of the Clock input,
after which the signal present at the input pin is sampled inside the device.
APERTURE JITTER (tAJ) is the variation in aperture delay from sample to sample. Aperture jitter shows up as
input noise.
CLOCK DUTY CYCLE is the ratio of the clock wave form logic high to the total time of one clock period.
CODE ERROR RATE (C.E.R.) is the probability of error and is defined as the probable number of errors per unit
of time divided by the number of words seen in that amount of time. A Code Error Rate of 10-18 corresponds to a
statistical error in one conversion about every four (4) years.
COMMON MODE VOLTAGE is the d.c. potential that is common to both pins of a differential pair. For a voltage
to be a common mode one, the signal departure from this d.c. common mode voltage at any given instant must
be the same for each of the pins, but in opposite directions from each other.
DIFFERENTIAL NON-LINEARITY (DNL) is the maximum deviation from the ideal step size of 1 LSB. Measured
at 3 Gsps with a sine wave input.
EFFECTIVE NUMBER OF BITS (ENOB, or EFFECTIVE BITS) is another method of specifying Signal-to-Noise
and Distortion Ratio, or SINAD. ENOB is defined as (SINAD − 1.76) / 6.02 and says that the converter is
equivalent to a perfect ADC of this (ENOB) number of bits.
FULL POWER BANDWIDTH (FPBW) is a measure of the frequency at which the reconstructed output
fundamental drops 3 dB below its low frequency value for a full scale input.
GAIN ERROR is the deviation from the ideal slope of the transfer function. It can be calculated from Offset and
Full-Scale Errors:
Pos. Gain Error = Offset Error − Pos. Full-Scale Error
(1)
(2)
(3)
Neg. Gain Error = − (Offset Error − Neg. Full-Scale Error)
Gain Error = Neg. Full-Scale Error − Pos. Full-Scale Error = Pos. Gain Error + Neg. Gain Error
INTEGRAL NON-LINEARITY (INL) is the maximum departure of the transfer curve from a straight line through
the input to output transfer function. The deviation of any given code from this straight line is measured from the
center of that code value. The best fit method is used.
INTERMODULATION DISTORTION (IMD) is the creation of additional spectral components as a result of two
sinusoidal frequencies being applied to the ADC input at the same time. It is defined as the ratio of the power in
the second and third order intermodulation products to the power in one of the original frequencies. IMD is
usually expressed in dBFS.
LSB (LEAST SIGNIFICANT BIT) is the bit that has the smallest value or weight of all bits. This value is
VFS / 2n
(4)
where VFS is the differential full-scale amplitude of VIN as set by the FSR input (pin-14) and "n" is the ADC
resolution in bits, which is 8 for the ADC08B3000.
MISSING CODES are those output codes that are skipped and will never appear at the ADC outputs. These
codes cannot be reached with any input value.
MSB (MOST SIGNIFICANT BIT) is the bit that has the largest value or weight. Its value is one half of full scale.
NEGATIVE FULL-SCALE ERROR (NFSE) is a measure of how far the first code transition is from the ideal 1/2
LSB above a differential -VIN / 2. For the ADC08B3000 the reference voltage is assumed to be ideal, so this error
is a combination of full-scale error and reference voltage error.
OFFSET ERROR (VOFF) is a measure of how far the mid-scale point is from the ideal zero voltage differential
input.
Offset Error = Actual Input causing average of 8k samples to result in an average code of 128.
OVER-RANGE RECOVERY TIME is the time required after the differential input voltages goes from ±1.2V to 0V
for the converter to recover and make a conversion with its rated accuracy.
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: ADC08B3000
ADC08B3000
SNAS331M –JUNE 2006–REVISED APRIL 2013
www.ti.com
POSITIVE FULL-SCALE ERROR (PFSE) is a measure of how far the last code transition is from the ideal 1-1/2
LSB below a differential +VIN / 2. For the ADC08B3000 the reference voltage is assumed to be ideal, so this
error is a combination of full-scale error and reference voltage error.
POWER SUPPLY REJECTION RATIO (PSRR) can be one of two specifications. PSRR1 (DC PSRR) is the ratio
of the change in full-scale error that results from a power supply voltage change from 1.8V to 2.0V. PSRR2 (AC
PSRR) is a measure of how well an a.c. signal riding upon the power supply is rejected from the output and is
measured with a 248 MHz, 100 mVP-P signal riding upon the power supply. It is the ratio of the output amplitude
of that signal at the output to its amplitude on the power supply pin. PSRR is expressed in dB.
SIGNAL TO NOISE RATIO (SNR) is the ratio, expressed in dB, of the rms value of the input signal at the output
to the rms value of the sum of all other spectral components below one-half the sample frequency, not including
harmonics or d.c.
SIGNAL TO NOISE PLUS DISTORTION (S/(N+D) or SINAD) is the ratio, expressed in dB, of the rms value of
the input signal at the output to the rms value of all of the other spectral components below half the input clock
frequency, including harmonics but excluding d.c.
SPURIOUS-FREE DYNAMIC RANGE (SFDR) is the difference, expressed in dB, between the rms values of the
input signal at the output and the peak spurious signal, where a spurious signal is any signal present in the
output spectrum that is not present at the input, excluding d.c.
TOTAL HARMONIC DISTORTION (THD) is the ratio expressed in dB, of the rms total of the first nine harmonic
levels at the output to the level of the fundamental at the output. THD is calculated as
2
2
f10
A
+ . . . + A
f2
THD = 20 x log
2
A
f1
(5)
where Af1 is the RMS power of the fundamental (output) frequency and Af2 through Af10 are the RMS power of
the first 9 harmonic frequencies in the output spectrum.
– Second Harmonic Distortion (2nd Harm) is the difference, expressed in dB, between the RMS power in the
input frequency seen at the output and the power in its 2nd harmonic level at the output.
– Third Harmonic Distortion (3rd Harm) is the difference expressed in dB between the RMS power in the input
frequency seen at the output and the power in its 3rd harmonic level at the output.
16
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: ADC08B3000
ADC08B3000
www.ti.com
SNAS331M –JUNE 2006–REVISED APRIL 2013
Transfer Characteristic
IDEAL
POSITIVE
FULL-SCALE
TRANSITION
Output
Code
ACTUAL
POSITIVE
FULL-SCALE
TRANSITION
1111 1111 (255)
1111 1110 (254)
1111 1101 (253)
POSITIVE
FULL-SCALE
ERROR
MID-SCALE
TRANSITION
1000 0000 (128)
0111 1111 (127)
OFFSET
ERROR
IDEAL NEGATIVE
FULL-SCALE TRANSITION
ACTUAL NEGATIVE
FULL-SCALE TRANSITION
NEGATIVE
FULL-SCALE
ERROR
0000 0010 (2)
0000 0001 (1)
0000 0000 (0)
(V +) < (V -)
IN IN
(V +) > (V -)
IN IN
0.0V
-V /2
+V /2
IN
IN
Differential Analog Input Voltage (+V /2) - (-V /2)
IN
IN
Figure 3. Input / Output Transfer Characteristic
TEST CIRCUIT DIAGRAMS
Timing Diagrams
Single Register Access
SCS
t
SCS
t
HCS
13
16
17
t
12
32
1
HCS
SCLK
SDATA
Fixed Header Pattern
Register Address
Register Write Data
LSB
MSB
t
SH
t
SSU
Figure 4. Serial Interface Timing
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links: ADC08B3000
ADC08B3000
SNAS331M –JUNE 2006–REVISED APRIL 2013
www.ti.com
Synchronizing Edge
CLK
t
HR
t
SR
DCLK_RST-
DCLK_RST+
t
PWR
Figure 5. Clock Reset Timing
t
CAL
t
CAL
CalRun
t
t
CAL_H
CalDly
Calibration Delay
determined by
CalDly Pin (127)
CAL
t
CAL_L
POWER
SUPPLY
Figure 6. Self Calibration and On-Command Calibration Timing
1
5
10
15
20
25
30
35
40
45
50
55
60
65
70
Sampling
Clock
WEN
FF asserted
FF cleared
EF cleared
EF asserted
FIFO
Contents
RCLK
REN
Figure 7. Capture Buffer Read Operation
18
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: ADC08B3000
ADC08B3000
www.ti.com
SNAS331M –JUNE 2006–REVISED APRIL 2013
Captured
Sample
X
X
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
13
14
14
15
15
16
16
CLK-
Write CLK
(Internal)
3T
WRITE CLOCK
WEN
WENSYNC
Vin
t
DWS
t
AD
Actual Sampling
Buffer
Capture
X
X
X
X
X
X
X
X
X
8
9
10
11
12
13
14
15
16
Figure 8. Capture Buffer Write Enable Timing - 7 Input Clock Cycles
Captured
Sample
X
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
17
CLK-
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Write CLK
(Internal)
3T
WRITE CLOCK
WEN
WENSYNC
Vin
t
DWS
t
AD
Actual Sampling
Buffer
Capture
X
X
X
X
X
X
X
X
X
9
10
11
12
13
14
15
16
17
Figure 9. Capture Buffer Write Enable Timing - 8 Input Clock Cycles
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Links: ADC08B3000
ADC08B3000
SNAS331M –JUNE 2006–REVISED APRIL 2013
www.ti.com
1
1
1
1
1
2
2
2
3
3
3
3
3
4
4
5
5
6
6
6
7
7
7
8
8
8
9
9
9
RCLK
D1 <7:0>
D1[1]
D1[2]
D1[3]
D1[4]
D1[5]
D1[6]
D1[7]
D1[8]
D1[9]
DRDY
SDR DRDY Clocking
(OutEdge = 1b)
4
5
RCLK
D1 <7:0>
D1[1]
D1[2]
D1[3]
D1[4]
D1[5]
D1[6]
D1[7]
D1[8]
D1[9]
DRDY
2
4
5
6
7
8
9
SDR DRDY Clocking
(OutEdge = 0b)
2
4
5
6
7
8
9
RCLK
D1 <7:0>
D1[1]
1
D1[2]
D1[3]
2
D1[4]
D1[5]
3
D1[6]
D1[7]
D1[8]
D1[9]
DRDY
4
5
0o Phase
tSO
tHO
DRDY
2
3
4
5
1
90o Phase
DDR DRDY Clocking
Figure 10. Capture Buffer DRDY Timing - SDR/DDR
RESET
WEN
WENsync
FF
FF deasserted when REN is asserted
tDFF
EF
REN
tSREN
tCYC
1
2
3
4
5
6
RCLK
D1 <7:0>
2TRCLK
D1[1]
D1[2]
D1[3]
D1[4]
D1[5]
tSKEW
First bit read out of Capture Buffer
tCYC
tDDRDY
While no valid data is transferred,
D and DRDY are forced low (OutEdge = 1b)
DRDY
1
2
3
4
5
6
A. For (OutEdge = 0b), all activity occurs on falling edge of DRDY.
Figure 11. Capture Buffer Beginning of READ Phase (OutEdge = 1b)
20
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: ADC08B3000
ADC08B3000
www.ti.com
SNAS331M –JUNE 2006–REVISED APRIL 2013
RESET
WEN
T
ASWEN(min)
REN must be deasserted and EF must be asserted
for (2) RCLKs before WEN can be asserted
WENsync
FF
EF asserted w/ last data read
EF
t
DEF1
from the Capture Buffer
REN
t
HREN1(min)
RCLK
D1 <7:0>
Last data bit out
512th data bit if BSIZE<1:0> = 00b
While no valid data is transferred,
D and DRDY are forced low (OutEdge = 1b)
DRDY
A. For (OutEdge = 0b), all activity occurs on falling edge of DRDY.
B. tHREN: REN is internally latched on the 3rd rising edge of RCLK (see Figure 12)
Figure 12. Capture Buffer End of READ Phase (OutEdge = 1b)
RESET
WEN
WENsync
FF
EF will not assert after early REN
EF
REN pulled low to stop READ phase
before Capture Buffer is completely empty
REN
RCLK
D1 <7:0>
While no valid data is transferred,
D and DRDY are forced low (OutEdge = 1b)
Last data bit out; data stopped (2) RCLK rising edges after REN
deassertion; 510th data bit if BSIZE<1:0> = 00b
2T
RCLK
DRDY
A. For (OutEdge = 0b), all activity occurs on falling edge of DRDY.
Figure 13. Capture Buffer Early REN Deassertion on READ Phase (OutEdge = 1b)
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
21
Product Folder Links: ADC08B3000
ADC08B3000
SNAS331M –JUNE 2006–REVISED APRIL 2013
www.ti.com
RESET
WEN
t
PWRST
WENsync
FF
EF
EF asserted w/ RESET
HREN2 (min)
t
DEF2
REN
t
RCLK
Last data bit out
507 data bit if BSIZE<1:0> = 00b
th
D1 <7:0>
While no valid data is transferred,
D and DRDY are forced low (OutEdge = 1b)
DRDY
A. For (OutEdge = 0b), all activity occurs on falling edge of DRDY.
Figure 14. Capture Buffer RESET on READ Phase (OutEdge = 1b)
RESET
WEN
t
PWRST
t
DWEN(min)
Write CLK
(Internal)
3T
WRITE CLK
WENsync
FF
t
DWS1
t
EF
DEF3
REN
D1 <7:0>
DRDY
Figure 15. Capture Buffer Beginning of WRITE Phase
22
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: ADC08B3000
ADC08B3000
www.ti.com
SNAS331M –JUNE 2006–REVISED APRIL 2013
RESET
WEN
t
HWEN (min)
Write CLK
(Internal)
WENsync
FF
t
DWS2
th
FF asserted with 512 data bit written into Capture Buffer
if BSIZE<1:0> = 00b
EF
3T
WRITE CLK
REN
D1 <7:0>
DRDY
A. tHWEN: WEN is internally latched on the 4th rising edge of the internal write clock (see Figure 16)
Figure 16. Capture Buffer End of WRITE Phase (ASW = 1b)
RESET
WEN deassertion
stops data storage
WEN
Write CLK
(Internal)
WENsync
FF
3T
t
DWS1
WRITE CLK
th
FF asserted with 512 data bit written into Capture Buffer
if BSIZE<1:0> = 00b
EF
7T
WRITE CLK
REN
D1 <7:0>
DRDY
Figure 17. Capture Buffer End of WRITE Phase (ASW = 0b)
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
23
Product Folder Links: ADC08B3000
ADC08B3000
SNAS331M –JUNE 2006–REVISED APRIL 2013
www.ti.com
Typical Performance Characteristics
VA=VDR=1.9V, fCLK=1500 MHz (i.e., Sample Rate = 3 Gsps), fIN=373 MHz, TA=25°C unless otherwise stated.
DNL vs. TEMPERATURE
INL vs. TEMPERATURE
Figure 18.
Figure 19.
DNL vs. CODE
INL vs. CODE
Figure 20.
Figure 21.
POWER CONSUMPTION vs. SAMPLE RATE
ENOB vs. TEMPERATURE
Figure 22.
Figure 23.
24
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: ADC08B3000
ADC08B3000
www.ti.com
SNAS331M –JUNE 2006–REVISED APRIL 2013
Typical Performance Characteristics (continued)
VA=VDR=1.9V, fCLK=1500 MHz (i.e., Sample Rate = 3 Gsps), fIN=373 MHz, TA=25°C unless otherwise stated.
ENOB vs. SUPPLY VOLTAGE
ENOB vs. SAMPLE RATE
Figure 24.
Figure 25.
ENOB vs. INPUT FREQUENCY
SNR vs. TEMPERATURE
Figure 26.
Figure 27.
SNR vs. SUPPLY VOLTAGE
SNR vs. SAMPLE RATE
Figure 28.
Figure 29.
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
25
Product Folder Links: ADC08B3000
ADC08B3000
SNAS331M –JUNE 2006–REVISED APRIL 2013
www.ti.com
Typical Performance Characteristics (continued)
VA=VDR=1.9V, fCLK=1500 MHz (i.e., Sample Rate = 3 Gsps), fIN=373 MHz, TA=25°C unless otherwise stated.
SNR vs. INPUT FREQUENCY
THD vs. TEMPERATURE
Figure 30.
Figure 31.
THD vs. SUPPLY VOLTAGE
THD vs. SAMPLE RATE
Figure 32.
Figure 33.
THD vs. INPUT FREQUENCY
SFDR vs. TEMPERATURE
Figure 34.
Figure 35.
26
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: ADC08B3000
ADC08B3000
www.ti.com
SNAS331M –JUNE 2006–REVISED APRIL 2013
Typical Performance Characteristics (continued)
VA=VDR=1.9V, fCLK=1500 MHz (i.e., Sample Rate = 3 Gsps), fIN=373 MHz, TA=25°C unless otherwise stated.
SFDR vs. SUPPLY VOLTAGE
SFDR vs. SAMPLE RATE
Figure 36.
Figure 37.
SFDR vs. INPUT FREQUENCY
Spectral Response at FIN = 373 MHz
Figure 38.
Figure 39.
Spectral Response at FIN = 748 MHz
Spectral Response at FIN = 1497 MHz
Figure 40.
Figure 41.
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
27
Product Folder Links: ADC08B3000
ADC08B3000
SNAS331M –JUNE 2006–REVISED APRIL 2013
www.ti.com
Typical Performance Characteristics (continued)
VA=VDR=1.9V, fCLK=1500 MHz (i.e., Sample Rate = 3 Gsps), fIN=373 MHz, TA=25°C unless otherwise stated.
FULL POWER BANDWIDTH
Figure 42.
FUNCTIONAL DESCRIPTION
The ADC08B3000 is a versatile A/D Converter with an innovative architecture permitting very high speed
operation. The controls available ease the application of the device to circuit solutions. Optimum performance
requires adherence to the provisions discussed here and in Applications Information.
While it is generally poor practice to allow an active pin to float, pins 4 and 14 of the ADC08B3000 are designed
to be left floating without jeopardy. In all discussions throughout this data sheet, whenever a function is called by
allowing a control pin to float, connecting that pin to a potential of one half the VA supply voltage will have the
same effect as allowing it to float.
OVERVIEW
The ADC08B3000 uses a calibrated folding and interpolating architecture that achieves very high performance.
The use of folding amplifiers greatly reduces the number of comparators and power consumption. Interpolation
reduces the number of front-end amplifiers required, minimizing the load on the input signal and further reducing
power requirements. In addition to other things, on-chip calibration reduces the INL bow often seen with folding
architectures. The result is an extremely fast, high performance, low power converter.
The analog input signal that is within the converter's input voltage range is digitized to eight bits at speeds of 1.0
Gsps to 3.4 Gsps, typical. Differential input voltages below negative full-scale will cause the output word to
consist of all zeroes. Differential input voltages above positive full-scale will cause the output word to consist of
all ones. Either of these conditions at the analog input will cause the OR (Out of Range) output to be activated.
This single OR output indicates when the output code from the converter is below negative full scale or above
positive full scale.
Calibration
A calibration is performed upon power-up and can also be invoked by the user upon command. Calibration trims
the 100Ω analog input differential termination resistor and minimizes full-scale error, offset error, DNL and INL,
resulting in maximizing SNR, THD, SINAD (SNDR) and ENOB. Internal bias currents are also set with the
calibration process. All of this is true whether the calibration is performed upon power up or is performed upon
command. Running the calibration is an important part of this chip's functionality and is required in order to obtain
adequate performance. In addition to the requirement to be run at power-up, calibration must be re-run by the
user whenever the state of the FSR pin is changed. For best performance, we recommend an on command
calibration be run after initial power up and the device has reached a stable temperature. Also, we recommend
that an on-command calibration be run 20 seconds or more after application of power and whenever the
operating temperature changes significantly relative to the specific system performance requirements. See On-
Command Calibration for more information. Calibration can not be initiated or run while the device is in the
power-down mode. See Power Down for information on the interaction between Power Down and Calibration.
28
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: ADC08B3000
ADC08B3000
www.ti.com
SNAS331M –JUNE 2006–REVISED APRIL 2013
In normal operation, calibration is performed just after application of power and whenever a valid calibration
command is given, which is holding the CAL pin low for at least 80 input clock cycles, then hold it high for at
least another 80 input clock cycles. The time taken by the calibration procedure is specified in the
AC ELECTRICAL CHARACTERISTICS section of Converter Electrical Characteristics. Holding the CAL pin high
during power up will prevent the calibration process from running until the CAL pin experiences the above-
mentioned 80 input clock cycles low followed by 80 cycles high.
CalDly (pin 127) is used to select one of two delay times from the application of power before the start of
calibration. This calibration delay is 225 input clock cycles (about 22 ms with a 1.5 GHz clock) with CalDly low, or
231 input clock cycles (about 1.4 seconds with a 1.5 GHz clock) with CalDly high. These delay values allow the
power supply to come up and stabilize before calibration takes place. If the PD pin is high upon power-up, the
calibration delay counter will be disabled until the PD pin is brought low. Therefore, holding the PD pin high
during power up will further delay the start of the power-up calibration cycle. The best setting of the CalDly pin
depends upon the power-on settling time of the power supply.
NOTE: These things should be noted regarding device calibration:
•
If the PD input is brought high while a calibration is running, the device will not go into power down until the
calibration sequence is complete. However, if power is applied and PD is already high, the device will not
begin the calibration sequence until the PD input goes low. If a manual calibration is requested while the
device is powered down, the calibration will not begin at all. That is, the manual calibration input is completely
ignored in the power down state.
•
•
During the calibration cycle, the OR output may be active as a result of the calibration algorithm. All data on
the output pins and the OR output are invalid during the calibration cycle.
If a calibration is initiated at any time after clock phase adjustment has been enabled (bit 15 of Coarse Clock
Phase Adjust Register, address Eh, set to 1b), the internal clock will stop running at the very beginning of the
calibration sequence. It is important to ensure that the clock phase enable bit is off (set to 0b), or that the
Resistor Trim Disable bit is on (set to 1b) before running an on-command calibration.
•
At least one calibration cycle must be run with the RTD bit in the Configuration Register cleared (at 0b) after
power-up to adjust the Analog Input Termination Resistor.
•
•
All input must be within operating norms during the entire calibration process.
The on-board registers must not be accessed during the calibration process, although the SCLK may be
active.
•
The CalRun output is high whenever the calibration procedure is running. This is true whether the calibration
is done at power-up or on-command.
Acquiring the Input
Data is acquired at both the rising and falling edges of CLK (pin 10). When a Write Enable (WEN) is initiated, the
converted data from the ADCs will be loaded into the Capture Buffer. Because of the asynchronous nature of
WEN to the sample clock, the Capture Buffer write will occur after the two ADCs have completed a full
conversion cycle. This allows the Capture Buffer to store the converted data in a predictable, ordered fashion.
The Capture Buffer will output its digital data at two, 8 bit wide LVCMOS outputs when initiated with the Read
Enable (REN) command. For more information on Capture Buffer operation, please refer to CAPTURE BUFFER
FUNCTIONAL DESCRIPTION and its subsections. Refer to the timing diagrams related to the Capture Buffer for
timing related information.
The ADC08B3000 will convert as long as the sample input clock signal is present. The ADC08B3000 output data
signaling is LVCMOS and the output format is offset binary.
Control Modes
Much of the user control can be accomplished with several control pins that are provided. Examples include
initiation of the calibration cycle, power down mode and full scale range setting. However, the ADC08B3000 also
provides an Extended Control mode whereby a serial interface is used to access register-based control of
several advanced features. The Extended Control mode is not intended to be enabled and disabled dynamically.
Rather, the user is expected to employ either the normal control mode or the Extended Control mode at all times.
When the device is in the Extended Control mode, pin-based control of several features is replaced with register-
based control and those pin-based controls are disabled. These pins are OutEdge/DDR (pin 4), FSR (pin 14) and
CalDly (pin 127). See THE SERIAL INTERFACE for details on the Extended Control mode.
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
29
Product Folder Links: ADC08B3000
ADC08B3000
SNAS331M –JUNE 2006–REVISED APRIL 2013
www.ti.com
The Analog Inputs
The ADC08B3000 must be driven with a differential input signal. Operation with a single-ended signal is not
recommended as performance will suffer. It is important that the input signals are either a.c. coupled to the inputs
with the VCMO pin grounded or d.c. coupled with the VCMO pin left floating or lightly loaded. An input common
mode voltage that is equal to and tracks the VCMO output must be provided when d.c. coupling is used.
In the Normal mode, the full-scale range is set to one of two levels, as indicated in Converter Electrical
Characteristics, with pin 14 (FSR). In the Extended Control Mode, the full-scale range may be set to one of 512
values, as described in REGISTER DESCRIPTION.
In the Extended Control mode, the full-scale input range can be set to values between 560 mVP-P and 840 mVP-P
through a serial interface. See NORMAL/EXTENDED CONTROL, THE SERIAL INTERFACE, and THE ANALOG
INPUT.
Clocking
The ADC08B3000 must be driven with an a.c. coupled, differential clock signal. THE SAMPLE CLOCK INPUT
describes the use of the clock input pins. This sample clock, CLK, has an optional duty cycle correction feature
which is enabled by default and provides improved ADC clocking. This circuitry allows the ADC to be clocked
with a signal source having a duty cycle of 20% to 80% (worst case).
To assist the user in reading captured data from the Capture Buffer, the ADC08B3000 has an RCLK input. RCLK
is a free-running clock which can be applied asynchronously with respect to the analog input sample clock and
can operate up to 200MHz. The data output, DRDY signals and EF flag are asserted synchronous with RCLK.
See CAPTURE BUFFER FUNCTIONAL DESCRIPTION and its subsections for information on reading the
Capture Buffer.
Dual-Edge Sampling
To achieve 3 Gsps with a 1.5 GHz sample clock, the device uses two ADCs, one sampling the input on the
positive edge of the sample clock and the other ADC sampling the same input on the negative edge of the
sample clock. The input is thus sampled twice per sample clock cycle, resulting in an overall sample rate of twice
the sample clock frequency.
The ADC08B3000 includes an automatic clock phase background adjustment which automatically and
continuously adjusts the phase of the rising and falling clock edges relative to each other. This feature removes
the need to manually adjust the clock phase and provides optimal ENOB performance.
Double Data Rate
Choice of single data rate (SDR) or double data rate (DDR) output is offered. To select the DDR mode, address
1h, bit 10 of the Configuration Register must be set to 0b. With single data rate the Data Ready (DRDY)
frequency is the same as the data rate of the two output buses. With double data rate the DRDY frequency is
half the data rate and data is sent to the outputs on both edges of DRDY. DDR clocking is enabled in non-
Extended Control mode by allowing pin 4 to float.
OutEdge Setting
To help ease data capture in the SDR mode, the output data may be caused to transition on either the positive or
the negative edge of the Data Ready (DRDY) Pins. This is chosen in the Normal mode with the OutEdge input
(pin 4). A high on the OutEdge input pin causes the output data to transition on the rising edge of DRDY, while
grounding this input causes the output to transition on the falling edge of DRDY. See Output Edge
Synchronization. In the Extended Control mode, the OutEdge setting is made with bit 8 of the Configuration
Register. See REGISTER DESCRIPTION.
Power Down
The ADC08B3000 is in the active state when the Power Down pin (PD) is low. When the PD pin is high, the
device is in the power down mode. In this power down mode the data output pins, DRDY, FF, EF, OR, REN,
RCLK and RESET are left active to allow the user to unload the Capture Buffer while the ADC core and the
Capture Buffer write circuitry power down to reduce the device power consumption to a minimal level.
See Calibration for information on the interaction of the power down and calibration functions.
30
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: ADC08B3000
ADC08B3000
www.ti.com
SNAS331M –JUNE 2006–REVISED APRIL 2013
NORMAL/EXTENDED CONTROL
The ADC08B3000 may be operated in one of two modes. In the Normal Control Mode, the user accomplishes
available configuration and control of the device through several control pins. The "extended control mode"
provides additional configuration and control options through the serial interface and a set of 6 internal registers.
The control mode is selected with pin 14 (FSR/ECE). The choice of control modes is required to be a fixed
selection and is not intended to be switched dynamically while the device is operational.
Table 1 shows how several of the device features are affected by the control mode chosen.0
Table 1. Features and Modes
Feature
SDR or DDR Clocking
Normal Control Mode
Extended Control Mode
Selected with nDE in the Configuration Register
(address 1h; bit 10). When the device is in DDR
mode, address 1h, bit 8 must be set to 0b.
Selected with pin 4
Selected with DCP in the Configuration Register
(address 1h; bit 11).
DDR Clock Phase
Not Selectable (0° Phase Only)
SDR Data transitions with rising or falling
DRDY edge
Selected with OE in the Configuration Register
(address 1h; bit 8).
Selected with pin 4
Power-On Calibration Delay
Delay Selected with pin 127
Short delay only.
512 step adjustments possible over a nominal
range of 560 mV to 840 mV by using the Full-
Scale Voltage Register (address 3h; bits 7
thru 15).
Two ranges selected with pin 14 as
described in Converter Electrical
Full-Scale Range
Characteristics(1)(2)
.
Up to ±45 mV adjustment in 512 steps in the
Offset Adjust Register (address 2h; bits 7
thru 15).
Input Offset Adjust
Not possible
The clock phase can be adjusted manually
through the Fine & Coarse registers (address Dh
and Eh).
Sample Clock Phase Adjustment
Test Pattern Output
Not possible
Not possible
A test pattern can be made present at the data
outputs by selecting TPO in the Test Pattern
Register (address Fh; bit 11).
(1) The analog inputs are protected as shown below. Input voltage magnitudes beyond the Absolute Maximum Ratings may damage this
device. See Figure 2
(2) To ensure accuracy, it is required that VA and VDR be well bypassed. Each supply pin must be decoupled with separate bypass
capacitors. Additionally, achieving rated performance requires that the backside exposed pad be well grounded.
The default state of the Extended Control Mode is set upon power-on reset (internally performed by the device)
and is shown in Table 2.
Table 2. Extended Control Mode Operation (Pin 14 Floating)
Feature
Calibration Delay
Extended Control Mode Default State
Short Delay
Full-Scale Range
700 mV nominal
Input Offset Adjust
Clock Phase Adjust - Fine
Clock Phase Adj - Course
Duty Cycle Stabilizer
DDR Clock Phase
DDR Enable
0 mV
0 ps Phase Adjust
0 ps Phase Adjust
Enabled
90° phase aligned
Single Data Rate, SDR
4K bytes
Capture Buffer Size
Auto-Stop Write
Writes to Capture Buffer will stop automatically
Data on data D1 only
Falling edge of DRDY
No test pattern
Two Port Enable
Output Edge
Test Pattern Output
Differential ADCCLK_RST Enable
Single-ended ADCCLK_RST
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
31
Product Folder Links: ADC08B3000
ADC08B3000
SNAS331M –JUNE 2006–REVISED APRIL 2013
www.ti.com
THE SERIAL INTERFACE
NOTE
IMPORTANT: During the initial write using the serial interface, all six registers must be
written with desired or default values. Subsequent writes to single registers are allowed.
The 3-pin serial interface is enabled only when the device is in the Extended Control mode. The pins of this
interface are Serial Clock (SCLK), Serial Data (SDATA) and Serial Interface Chip Select (SCS). Eight write only
registers are accessible through this serial interface. Registers are write only and can not be read back.
SCS: This signal must be asserted low to access a register through the serial interface. Setup and hold times
with respect to the SCLK must be observed.
SCLK: Serial data input is accepted at the rising edge of this signal. There is no minimum frequency requirement
of this signal.
SDATA: Each register access requires a specific 32-bit pattern at this input. This pattern consists of a header,
register address and register value. The data is shifted in MSB first. Setup and hold times with respect to the
SCLK must be observed. See the Timing Diagram of Figure 4.
Each Register access consists of 32 bits, as shown in Figure 4 of the Timing Diagrams. The fixed header pattern
is 0000 0000 0001 (eleven zeros followed by a 1). The loading sequence is such that a "0" is loaded first. The
next 4 bits are the address of the register that is to be written to and the last 16 bits are the data written to the
addressed register. The addresses of the various registers are indicated in Table 3. Refer to REGISTER
DESCRIPTION for information on the data to be written to the registers. Subsequent register accesses may be
performed immediately, starting with the 33rd SCLK. This means that the SCS input does not have to be de-
asserted and asserted again between register addresses. It is possible, although not recommended, to keep the
SCS input permanently enabled (at a logic low) when using extended control.
NOTE
IMPORTANT: The Serial Interface should not be accessed while the ADC is undergoing a
calibration cycle. Doing so will impair the performance of the device until it is re-calibrated
correctly. Programming the serial registers will also reduce dynamic performance of the
ADC for the duration of the register access time.
Table 3. Register Addresses
4-Bit Address
Loading Sequence: A3 loaded after Fixed Header Pattern, A0 loaded last
A3
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
A2
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
A1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
A0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Hex
0h
1h
2h
3h
4h
5h
6h
7h
8h
9h
Ah
Bh
Ch
Dh
Eh
Fh
Register Addressed
Reserved
Configuration
Offset
Full-Scale Voltage Adjust
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Extended Clock Phase Adjust Fine
Extended Clock Phase Adjust Coarse
Capture Buffer
32
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: ADC08B3000
ADC08B3000
www.ti.com
SNAS331M –JUNE 2006–REVISED APRIL 2013
REGISTER DESCRIPTION
Six write-only registers provide several control and configuration options in the Extended Control Mode. These
registers have no effect when the device is in the Normal Control Mode. Each register description below also
shows the Power-On Reset (POR) state of each control bit.
The contents of the all registers are retained when the device is in the Power Down mode.
Table 4. Configuration Register
Addr: 1h (0001b)
D15
1
D14
D13
D12
D11
D10
nDE
D9
1
D8
DRE
RTD
DCS
DCP
OE
D7
1
D6
1
D5
1
D4
1
D3
1
D2
1
D1
1
D0
1
Bit 15
Bit 14
Must be set to 1b
DRE: Differential Reset Enable. When this bit is set to 0b, it enables the single-ended ADCCLK_RST input.
When this bit is set to 1b, it enables the differential ADCCLK_RST input.
POR State: 0b
Bit 13
RTD: Resistor Trim Disable. The state of this bit determines whether the input signal termination resistor is
trimmed or not during the calibration cycle. If the Clock Phase Adjust feature is enabled (ENA bit is set to 1b in
register Eh), then this bit must be set to 1b also.
NOTE: The input termination resistor MUST be trimmed at least once, which will only happen if this bit is 0b.
The Power-Up self-calibration cycle will trim the termination resistor as the power-up default value of this bit
is 0b.
POR State: 0b
Bit 12
Bit 11
DCS: Duty Cycle Stabilizer. When this bit is set to 1b, a duty cycle stabilization circuit is applied to the clock
input. When this bit is set to 0b the stabilization circuit is disabled.
POR State: 1b
DCP: DDR Clock Phase. This bit only has an effect in the DDR mode. When this bit is set to 0b, the DRDY
edges are time-aligned with the data bus edges (“0° Phase”). When this bit is set to 1b, the DRDY edges are
placed in the middle of the data bit cells (“90° Phase”).
POR State: 1b
Bit 10
nDE: DDR Enable. When this bit is set to 0b, data bus clocking follows the DDR (Dual Data Rate) mode
whereby a data word is output with each rising and falling edge of DRDY. When this bit is set to a 1b, data bus
clocking follows the SDR (Single Data Rate) mode whereby each data word is output with either the rising or
falling edge of DRDY, as determined by the OutEdge bit.
POR State: 1b
Bit 9
Bit 8
Must be set to 1b
OE: Output Edge. This bit selects the edge of the DRDY pins with which the data words transition in the SDR
mode and has the same effect as the OutEdge pin in the normal control mode. When this bit is set to 1b, the
data outputs change with the rising edge of the DRDY pins. When this bit is set to 0b, the data outputs change
with the falling edge of the DRDY pins.
POR State: 0b
Bits 7:0
Must be set to 1b.
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
33
Product Folder Links: ADC08B3000
ADC08B3000
SNAS331M –JUNE 2006–REVISED APRIL 2013
www.ti.com
Table 5. Offset Adjust
Addr: 2h (0010b)
D15
(MSB)
D14
D13
D12
D11
D10
D9
D8
Offset Value
(LSB)
D7
D6
1
D5
1
D4
1
D3
1
D2
1
D1
1
D0
1
Sign
Bits 15:8
Offset Value. The input offset of the ADC is adjusted linearly and monotonically by the value in this field. 00h
provides a nominal zero offset, while FFh provides a nominal 45 mV of offset. Thus, each code step provides
0.176 mV of offset.
POR State: 0000 0000 b (no adjustment)
Sign bit. 0b gives positive offset, 1b gives negative offset.
POR State: 0b
Bit 7
Bit 6:0
Must be set to 1b
Table 6. Full-Scale Voltage Adjust
Addr: 3h (0011b)
D15
D14
D13
D12
D11
D10
D9
D8
(MSB)
Adjust Value
D7
D6
1
D5
1
D4
1
D3
1
D2
1
D1
1
D0
1
(LSB)
Bit 15:7
Full Scale Voltage Adjust Value. The input full-scale voltage or gain of the ADC is adjusted linearly and
monotonically with a 9 bit data value. The adjustment range is ±20% of the nominal 700 mVP-P differential
value.
0000 0000 0
560mVP-P
700mVP-P
840mVP-P
1000 0000 0 Default Value
1111 1111 1
For best performance, it is recommended that the value in this field be limited to the range of 0110 0000 0b to
1110 0000 0b. i.e., limit the amount of adjustment to ±15%. The remaining ±5% headroom allows for the ADC's
own full scale variation. A gain adjustment does not require ADC re-calibration.
POR State: 1000 0000 0b
Must be set to 1b
Bits 6:0
Table 7. Sample Clock Phase Adjust Fine
Addr: Dh (1101b)
D15
D14
D13
D12
D11
D10
D9
D8
(MSB)
Fine Phase Adjust
D7
D6
1
D5
1
D4
1
D3
1
D2
1
D1
1
D0
1
(LSB)
Bit 15:7
Bit 6:0
Fine Adjust Magnitude. The phase of the ADC sample clock is adjusted monotonically by the value in this
register. A value of 00h provides a nominal zero phase adjustment, while 1FFh provides a nominal 110ps
delay.
POR State: 0000 0000 0b
Must be set to 1b
34
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: ADC08B3000
ADC08B3000
www.ti.com
SNAS331M –JUNE 2006–REVISED APRIL 2013
Table 8. Sample Clock Phase Adjust Coarse
Addr: Eh (1110b)
D15
D14
D13
D12
D11
D10
LFS
D9
1
D8
1
ENA
CAM
D7
1
D6
1
D5
1
D4
1
D3
1
D2
1
D1
1
D0
1
Bit 15
Enable Sample Clock Phase Adjust. Default is 0b. When this feature is enabled, the RTD bit in register 1h
MUST also be enabled to ensure proper calibration.
Bit 14:11
Coarse Adjust Magnitude. Each LSB results in approximately 70ps of clock adjust.
POR State: 0000b
Bit 10
Low Frequency Sample clock. When this bit is set 1b, the dynamic performance of the device is improved when
the sample clock is less than 900MHz.
POR State: 0b
Bits 9:0
Must be set to 1b
NOTE: When this feature is enabled, the RTD bit in register 1h must also be enabled.
Table 9. Capture Buffer Register
Addr: Fh (1111b)
D15
D14
D13
D12
TPE
D11
D10
1
D9
1
D8
1
BSIZE
ASW
TPO
D7
1
D6
1
D5
1
D4
1
D3
1
D2
1
D1
1
D0
1
Bit 15
Bit 14
Bit 13
BSIZE<1>: This bit in combination with BSIZE<0> (BIT 14) is used to select the buffer size of the Capture
Buffer. The Capture Buffer is size adjustable and it cannot be split between the two LVCMOS data output ports.
See CAPTURE BUFFER FUNCTIONAL DESCRIPTION for a table which relates the Capture Buffer size to
BSIZE<1:0> programming.
POR State: 1b
BSIZE<0>: This bit in combination with BSIZE<1> (BIT 15) is used to select the buffer size of the Capture
Buffer. The Capture Buffer is size adjustable and it cannot be split between the two LVCMOS data output ports.
See CAPTURE BUFFER FUNCTIONAL DESCRIPTION for a table which relates the Capture Buffer size to
BSIZE<1:0> programming.
POR State: 1b
ASW: Auto-Stop Write. When ASW is set to 1b, Capture Buffer writing will stop automatically when the Capture
Buffer is full of captured data and the FF flag is asserted. If this bit is set to 0b, the device will continuously
write data to the Capture Buffer while overwriting previously captured data.
POR State: 1b
Bit 12
Bit 11
TPE: Two Port Output Enable. When this bit is set to 1b, data stored in the Capture Buffer will appear on two 8
bit output ports. When this bit is set to 0b, data will only appear on the D1 8 bit output port.
POR State: 0b
TPO: Test Pattern Output enable. When this bit is set 1b, the ADC is disengaged and a test pattern generator
is connected to the outputs including the OR output. This test pattern will work with the device in either the
SDR and DDR modes. See ADC TEST PATTERN OUTPUT.
POR State: 0b
Bits10:0
Must be set to 1b
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
35
Product Folder Links: ADC08B3000
ADC08B3000
SNAS331M –JUNE 2006–REVISED APRIL 2013
www.ti.com
Clock Phase Adjustment
This is a feature intended to help the system designer remove small imbalances in clock distribution traces at the
board level when multiple ADCs are used. Please note, however, that enabling this feature will reduce the
dynamic performance (SNR, ENOB, SFDR) some finite amount. The amount of degradation increases with the
amount of adjustment applied. The user is strongly advised to use the minimal amount of adjustment and to
verify the net benefit of this feature in his system before relying upon it.
Extended Mode Offset Correction
For offset values of +0000 0000 and -0000 0000, the actual offset is not the same. By changing only the sign bit
in this case, an offset step in the digital output code of about 1/10th of an LSB is experienced. This is shown
more clearly in the Figure 43.
Figure 43. Extended Mode Offset Behavior
MULTIPLE ADC SYNCHRONIZATION
The ADC08B3000 has the capability to precisely reset its sample clock input to support the synchronization of
multiple ADCs in a system. The ADCCLK_RST allows multiple ADCs in a system to be synchronized so that
there is a known relationship between the sampling times of all ADCs.
The ADC08B3000 has been designed to accommodate systems which require a single-ended (LVCMOS)
ADCCLK_RST and those using a differential (LVDS) ADCCLK_RST. In either case, the ADCCLK_RST signal
must observe the timing requirements shown in Figure 5 of the Timing Diagrams. The ADCCLK_RST pulse must
be of a minimum width and its deassertion edge must observe setup and hold times with respect to the CLK
input rising edge. These timing specifications are listed as tHR, tSR, and tPWR. The duration of the ADCCLK_RST
pulse affects the length of time before valid data can be captured, so minimizing this pulse width is
recommended.
Single-Ended (LVCMOS) ADCCLK_RST: The Power on Reset state of ADCCLK_RST is to have single-ended
ADCCLK_RST activated. That is, bit 14, (DRE) in the Configuration Register is low, 0b. When not using singled-
ended ADCCLK_RST, this input pin should be grounded. When using the single-ended ADCCLK_RST, consider
the ADCCLK_RST+ signal of Figure 5 and ignore ADCCLK_RST-.
36
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: ADC08B3000
ADC08B3000
www.ti.com
SNAS331M –JUNE 2006–REVISED APRIL 2013
Differential (LVDS) ADCCLK_RST: Activated by setting bit 14 (DRE) of the configuration register high, 1b.
When the differential ADCCLK_RST is not activated (that is, when bit 14 of the Configuration Register is 0b),
these inputs should be grounded. Differential ADCCLK_RST has an internal 100 ohm termination resistor and
should be DC coupled, not be AC coupled.
The ADCCLK_RST signal can be asserted asynchronous to the input clock. When the ADCCLK_RST signal is
de-asserted in synchronization with the CLK rising edge, the next CLK falling edge synchronizes the
ADC08B3000 with the other ADC08B3000s in the system. The user has the option of using a single-ended
ADCCLK_RST signal, but a differential ADCCLK_RST is strongly recommended due to its superior timing
performance.
ADC TEST PATTERN OUTPUT
To aid in system debug, the ADC08B3000 has the capability of providing a test pattern at the 2 outputs
completely independent of the input signal. By default, the test pattern will only appear at the D1 port. To have
the test pattern appear at both D1 and D2 ports, bit 12 (TPE) must be programmed to 1b in the Capture Buffer
Register (address Fh). Refer to REGISTER DESCRIPTION. To engage the test pattern, bit 11 (TPO) must be
programmed to 1b in the Capture Buffer Register (address Fh). When the test pattern is enabled, the ADC is
disengaged and a test pattern generator is connected to the output ports, including OR. The OR output is
asserted high at the start of the test pattern output and will remain high until the data is read out of the Capture
Buffer and the Empty Flag (EF) is asserted high. Each port can output a unique pattern sequence as described
in Table 10 and Table 11. The test pattern appears on the output port with the transition of DRDY.
Table 10. Test Pattern Output By Port in One Port Output SDR Mode
Time
T0
Port D1
01h
02h
03h
04h
FEh
FDh
FCh
FBh
01h
02h
03h
04h
FEh
FDh
FCh
FBh
01h
02h
03h
04h
Port D2
OR
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Comments
T1
T2
T3
T4
T5
T6
T7
T8
T9
Hi-Z
Pattern Sequence n
T10
T11
T12
T13
T14
T15
T16
T17
T18
T19
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
37
Product Folder Links: ADC08B3000
ADC08B3000
SNAS331M –JUNE 2006–REVISED APRIL 2013
www.ti.com
Table 10. Test Pattern Output By Port in One Port Output SDR Mode (continued)
Time
T20
T21
T22
T23
T24
T25
T26
T27
T28
T29
T30
Port D1
01h
02h
03h
04h
FEh
FDh
FCh
FBh
01h
02h
...
Port D2
OR
1
Comments
1
1
1
1
Hi-Z
1
Pattern Sequence n+1
1
1
1
1
...
Table 11. Test Pattern Output By Port in Two Port Output SDR Mode
Time
T0
Port D1
02h
04h
FDh
FBh
02h
04h
FDh
FBh
02h
04h
02h
04h
FDh
FBh
02h
...
Port D2
01h
03h
FEh
FCh
01h
03h
FEh
FCh
01h
03h
01h
03h
FEh
FCh
01h
...
OR
1
Comments
T1
1
T2
1
T3
1
T4
1
Pattern Sequence n
T5
1
T6
1
T7
1
T8
1
T9
1
T10
T11
T12
T13
T14
T15
1
1
1
Pattern Sequence n+1
1
1
...
CAPTURE BUFFER FUNCTIONAL DESCRIPTION
With the integration of the Capture Buffer, the ADC08B3000 allows sampling and processing tasks to be
separated. The intent is that the input signal can be sampled at a high rate and collected samples can be off-
loaded for digital processing at a slower rate. There are 5 main signals which are used to coordinate the
handshaking between the Capture Buffer data capture operation and the Capture Buffer read operation. These
five signals are Write Enable (WEN), Read Enable (REN), Empty Flag (EF), Full Flag (FF) and RESET.
It is important to note that the Capture Buffer implemented in this product is not a general purpose FIFO. The
Capture Buffer size is programmable in the Extended Control Mode using bit 15 (BSIZE<1>) and bit 14
(BSIZE<0>) in the Capture Buffer Register. See Table 12. In order for a Capture Buffer read to commence, the
entire buffer has to be filled. It is not possible to write to and read from the Capture Buffer simultaneously.
Table 12. Programmable Capture Buffer Size
BSIZE<1>
BSIZE<0>
Buffer Size (Bytes)
0
0
1
1
0
1
0
1
512
1024
2048
4096
38
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: ADC08B3000
ADC08B3000
www.ti.com
SNAS331M –JUNE 2006–REVISED APRIL 2013
Error Flags
The ADC08B3000 provides two output control signals, the Full Flag (FF) and the Empty Flag (EF), to monitor the
status of the Capture Buffer. Following the assertion of REN and the subsequent reading of the Capture Buffer,
the Empty Flag (EF) will be asserted by the device to indicate that the last data was read and the Capture Buffer
is now empty. Once the (EF) Empty Flag is asserted by the device, the user cannot re-read the Capture Buffer.
Only when Empty Flag (EF) is asserted high can a Capture Buffer data capture or WEN operation begin. The
assertion of WEN clears the Empty Flag (EF).
The data can only be read from the Capture Buffer when the buffer is full. That is, when FF (Full Flag) is high.
Once the FF is high, the data is ready to be read from the Capture Buffer on the rising edges of RCLK. The
assertion of REN clears the Full Flag (FF).
The assertion of a RESET signal clears the Full Flag (FF), sets the Empty Flag (EF) and clears both the data
capture to buffer and the buffer read operations.
Writing to the Capture Buffer
An internally generated write clock is used to write the converted data into the Capture Buffer. The write clock is
the same speed as the ADC Sample Clock. Unless the chip is in a power-down state, the ADC is always
converting the input signal. The data is stored in the Capture Buffer only when the Write Enable (WEN) signal is
asserted.
After the Capture Buffer is full and the Full Flag (FF) is asserted, new data will start writing over the oldest data
because the Write Pointer will wrap-around. The user has the option to stop the writing of the Capture Buffer
automatically upon a full condition with the use of the ASW (Auto-Stop Write) input. This is done in the Extended
Control Mode by setting bit 13 in the Capture Buffer register to 1b. Refer to REGISTER DESCRIPTION.
When the data is completely read from the Capture Buffer, the Empty Flag (EF) will be asserted by the device.
Only at this point can another data capture sequence begin (by the assertion of WEN). The assertion and
internal synchronization of WEN clears the Empty Flag (EF).
Reading from the Capture Buffer
Once the Full Flag (FF) is asserted high, the data is ready to be read from the Capture Buffer on the rising edges
of RCLK, which is an externally applied free-running clock that can be asynchronous with respect to the ADC
sample clock. To read the data out of the Capture Buffer, the Read Enable (REN) signal must be asserted. The
Full Flag (FF) is cleared with the assertion and internal synchronizing of REN. An Empty Flag (EF) will be
asserted by the device to indicate that the last data was read and the Capture Buffer is now empty.
When the Two Port Output Enable is set to 0b in the Capture Buffer Register (addr: Fh, bit: 12 (TPE)), only port
D1 will be enabled for data extraction from the Capture Buffer. When the Two Port Output Enable is set to 1b in
the Capture Buffer Register, ports D1 and D2 will be enabled for data extraction. For interleaving purposes, the
format of data is in 8-bit words with D2 outputting the first 8-bits from the Capture Buffer followed by D1 and back
to D2. Data output order is the same as the Test Pattern Output mode data output order. See Table 11 for data
order in Test Pattern Output mode.
Coordinating Read Enable (REN) and Write Enable (WEN)
It is not possible to write to and read from the Capture Buffer simultaneously. This means that the Write Enable
(WEN) and the Read Enable (REN) signals should not be asserted simultaneously. If the Read Enable (REN)
and Write Enable (WEN) signals are asserted at the same time, the Write Enable (WEN) signal supersedes and
the Read Enable (REN) signal is ignored. This is true even if the Read Enable (REN) signal is asserted first and
the buffer read operation is progressing normally. If the Write Enable (WEN) signal is asserted while Read
Enable (REN) is asserted, the Capture Buffer will freeze its operation until a RESET is applied. Recall that
RESET allows the Capture Buffer pointers to be reset so a new data capture operation can begin.
Capture Buffer Reset
The RESET signal clears FF and sets EF and halts both the data capture and data read operations. The RESET
signal can be useful during a partial read scenario where the data read operation stops early and the EF is not
asserted by the device. In this case the RESET signal allows the Capture Buffer pointers to be reset so a new
data capture operation can begin. The RESET signal has no effect upon the operation of the ADC, which has its
own internal Power-On Reset circuit.
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
39
Product Folder Links: ADC08B3000
ADC08B3000
SNAS331M –JUNE 2006–REVISED APRIL 2013
www.ti.com
Data Ready and Write Enable Sync
The ADC08B3000 has three other signals available to coordinate the Capture Buffer data capture and Capture
Buffer read operations. These signals are Data Ready Port 1 (DRDY1), Date Ready Port 2 (DRDY2), and Write
Enable Sync (WENSYNC). Data Ready Port 1 (DRDY1) and Data Ready Port 2 (DRDY2) can be used as latch
clocks for external systems as there are applications where using RCLK alone to capture the data on the data
output ports D1 and D2 is not practical. The Data Ready (DRDY) pins offer improved data capture capability by
eliminating the impact of the RCLK path delay and the internal RCLK-to-DataOut delay. Data Ready (DRDY) is
presented on the output ports at the same time as the data output. RCLK is used by the device to clock the data
out of the Capture Buffer and the DRDY signals are used to clock that data into the receiving circuit. The output
data and DRDY signals appear at the output ports three rising edges of RCLK after the assertion of REN.
Write Enable Sync (WENSYNC) is a synchronized version of Write Enable (WEN) and is synchronized with the
ADC sample clock. Write Enable Sync (WENSYNC) is provided as an output because Write Enable (WEN) can
be asserted completely asynchronous with the ADC sample clock, therefore it would be difficult for the user to
know exactly when the data capture operation actually began. Write Enable Sync (WENSYNC) allows the user to
determine this.
Out of Range
Out of Range (OR) is a signal used to determine if the input signal has over gone out of range at any time during
a data capture operation. It is asserted if an Out of Range condition occurred during the data capture operation
and is cleared only after the Capture Buffer read operation is complete and the Empty Flag (EF) is asserted. The
OR output is invalid during a calibration cycle.
Applications Information
THE REFERENCE VOLTAGE
The voltage reference for the ADC08B3000 is derived from a 1.254V bandgap reference, a buffered version of
which is made available at pin 31, VBG, for user convenience. This output has an output current capability of
±100 μA. This reference voltage should be buffered if more current is required.
The internal bandgap-derived reference voltage has a choice of two nominal values in the Normal mode as
determined by the FSR pin and described in The Analog Inputs.
There is no provision for the use of an external reference voltage, but the full-scale input voltage can be set to
one of two values in the Normal mode, as shown in the Electrical Tables, or it can be set through the Full-Scale
Voltage Adjust Register in the Extended Control mode to one of 512 values, as explained in
NORMAL/EXTENDED CONTROL. Never drive this pin.
Differential input signals up to the chosen full-scale level will be digitized to 8 bits. Signal excursions beyond the
full-scale range will be clipped at the output.
THE ANALOG INPUT
The analog input is a differential one to which the signal source may be a.c. coupled or d.c. coupled. The full-
scale input range is selected with the FSR pin, or can be adjusted to one of 512 values in the Extended Control
mode through the Serial Interface. For best performance it is recommended that the full-scale range be kept
between 595 mVP-P and 805 mVP-P in the Extended Control mode because the internal DAC which sets the full-
scale range is not as linear at the ends of its range.
Table 13 gives the input to output relationship with the FSR pin high when the Normal (non-extended) mode is
used. With the FSR pin grounded, the millivolt values in Table 13 are reduced to about 75% (600/810) of the
values indicated. In the Enhanced Control Mode, these values will be determined by the full scale range and
offset settings in the Control Registers.
40
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: ADC08B3000
ADC08B3000
www.ti.com
SNAS331M –JUNE 2006–REVISED APRIL 2013
Table 13. DIFFERENTIAL INPUT TO OUTPUT RELATIONSHIP (Non-Extended Control Mode, FSR High)
VIN
+
VIN
−
Output Code
0000 0000
0100 0000
V
CM − 405 mV
VCM + 405 mV
V
CM − 202.5 mV
VCM + 202.5 mV
0111 1111 /
1000 0000
VCM
VCM
VCM + 202.5 mV
VCM + 405 mV
V
CM − 202.5 mV
1100 0000
1111 1111
V
CM − 405 mV
The internally buffered analog inputs simplify the task of driving these inputs and the RC pole that is generally
used at sampling ADC inputs is not required. If it is desired to use an amplifier circuit before the ADC, use care in
choosing an amplifier with adequate noise and distortion performance and adequate gain at the frequencies used
for the application.
The Input impedance of the analog input in the d.c. coupled mode (VCMO pin not grounded) consists of a
precision 100Ω resistor across the inputs and a capacitance from each of these inputs to ground. In the a.c.
coupled mode, the input appears the same except there is also a resistor of 50KΩ between each analog input
pin and the on-chip VCMO potential.
When the inputs are a.c. coupled, the VCMO output must be grounded, as shown in Figure 44. This causes the
on-chip VCMO voltage to be connected to the inputs through on-chip 50KΩ resistors.
C
C
couple
couple
V +
IN
V -
IN
V
CMO
ADC08B3000
Figure 44. Differential Data Input Connection
When the d.c. coupled mode is used, a precise common mode voltage must be provided at the differential
inputs. This common mode voltage should track the VCMO output pin. Note that the VCMO output potential will
change with temperature. The common mode output of the driving device should track this change.
Full-scale distortion performance falls off rapidly as the input common mode voltage deviates from VCMO. This is
a direct result of using a very low supply voltage to minimize power. Keep the input common voltage within
50 mV of VCMO
.
Performance is as good in the d.c. coupled mode as it is in the a.c. coupled mode, provided the input common
mode voltage at both analog inputs remain within 50 mV of VCMO
.
Handling Single-Ended Input Signals
There is no provision for the ADC08B3000 to adequately process single-ended input signals. The best way to
handle single-ended signals is to convert them to differential signals before presenting them to the ADC.
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
41
Product Folder Links: ADC08B3000
ADC08B3000
SNAS331M –JUNE 2006–REVISED APRIL 2013
www.ti.com
A.C. Coupled Input
The easiest way to accomplish single-ended to differential conversion for a.c. signals is with an appropriate
balun, as shown in Figure 45. This figure is a generic depiction of a single-ended to differential signal conversion
using a balun. The balun-specific circuitry will depend upon the type of balun selected and the overall board
layout. It is recommended that the manufacturer of the selected balun be contacted for aid in designing the best
performing single-ended to differential conversion circuit using that particular balun.
C
COUPLE
Signal
Input
To V +
IN
Balun
To V -
IN
C
COUPLE
Figure 45. Single-Ended to Differential Signal Conversion with a Balun
When selecting a balun, it is important to understand the input architecture of the ADC. There are specific balun
parameters about which the system designer should be mindful. Match the impedance of the analog source to
transmission path and that path to the ADC08B3000’s on-chip 100Ω differential input termination resistor. The
range of this input termination resistor is described in Converter Electrical Characteristics as the specification RIN.
The phase and amplitude balance are important. The lowest possible phase and amplitude imbalance is desired
when selecting a balun. The phase imbalance should be no more than ±2.5° and the amplitude imbalance should
be limited to less than 1dB at the desired input frequency range.
Finally, when selecting a balun, the VSWR (Voltage Standing Wave Ratio), bandwidth and insertion loss of the
balun should also be considered. The VSWR aids in determining the overall transmission line termination
capability of the balun when interfacing to the ADC input. The insertion loss should be considered so that the
signal at the balun output is within the desired input range at the ADC input.
42
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: ADC08B3000
ADC08B3000
www.ti.com
SNAS331M –JUNE 2006–REVISED APRIL 2013
D.C. Coupled Input
When d.c. coupling to the ADC08B3000 analog input is required, single-ended to differential conversion may be
easily accomplished with the LMH6555 fully differential amplifier. An example of this type of circuit is shown in
Figure 46. In such applications, the LMH6555 performs the task of single-ended to differential conversion while
delivering low distortion and noise, as well as output balance, that supports the operation of the ADC08B3000.
Connecting the ADC08B3000 VCMO pin to the VCM_REF pin of the LMH6555 will ensure that the common mode
input voltage is as needed for optimum performance of the ADC08B3000. The LMV321 was chosen to buffer
VCMO for its low voltage operation and reasonable offset voltage.
3.3V
LMH6555
RF1
RT2
50W
V -
IN
RG1
-
+
Signal
Input
50W
RT1
50W
RG2
V +
IN
RF2
VCM_REF
+
-
V
CMO
LMV321
Figure 46. Example of Servoing the Analog Input with VCMO
Be sure that the current drawn from the VCMO output does not exceed 100 μA.
In Figure 46, RADJ-and RADJ+ are used to adjust the differential offset that can be measured between the ADC
inputs VIN+ and VIN-. An unadjusted positive offset greater than 15mV should be reduced with a resistor in the
RADJ-position. Likewise, an unadjusted negative offset more negative than −15mV should be reduced with a
resistor in the RADJ+ position. Table 14 gives suggested RADJ-and RADJ+ values for various unadjusted differential
offsets to bring the offset between VIN+ and VIN-back to within |15mV|. The circuit of Figure 46 assumes a 50Ω
d.c. coupled driving source.
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
43
Product Folder Links: ADC08B3000
ADC08B3000
SNAS331M –JUNE 2006–REVISED APRIL 2013
www.ti.com
Table 14. D.C. Coupled Offset Adjustment
Unadjusted Offset Reading
0mV to 10mV
Resistor Value
no resistor needed
20.0kΩ
11mV to 30mV
31mV to 50mV
10.0kΩ
51mV to 70mV
6.81kΩ
71mV to 90mV
4.75kΩ
91mV to 110mV
3.92kΩ
Out Of Range (OR) Indication
When the conversion result is clipped the Out of Range output is activated such that OR+ goes high and OR-
goes low. This output is active as long as accurate data on either or both of the buses would be outside the
range of 00h to FFh. The OR output is invalid During a calibration cycle.
Full-Scale Input Range
As with all A/D Converters, the input range is determined by the value of the ADC's reference voltage. The
reference voltage of the ADC08B3000 is derived from an internal band-gap reference. In the Normal Mode, the
FSR pin controls the effective reference voltage of the ADC08B3000 such that the differential full-scale input
range at the analog inputs is one value with the FSR pin high and another value with the FSR pin low. These full
scale values are in Converter Electrical Characteristics. In the Extended Control Mode, the Full Scale Range can
be set to any of 512 values, as indicated in the Full-Scale Adjust Register description of REGISTER
DESCRIPTION. Best SNR is obtained with higher Full Scale Ranges, but better distortion and SFDR are
obtained with lower Full Scale Ranges. The LMH6555 of Figure 46 is suitable for any Full Scale Range capability
of the ADC08B3000.
THE SAMPLE CLOCK INPUT
The ADC08B3000 has a differential LVDS clock input which must be driven with an a.c. coupled, differential
clock signal. Although the ADC08B3000 is tested and its performance is ensured with a differential 1.5 GHz
clock, it typically will function well with input clock frequencies indicated in Converter Electrical Characteristics.
The clock inputs are internally terminated and biased. The input clock signal must be capacitively coupled to the
clock pins as indicated in Figure 47.
Operation up to the sample rates indicated in Converter Electrical Characteristics is typically possible if the
maximum ambient temperatures indicated are not exceeded. Operating at higher sample rates than indicated for
the given ambient temperature may result in reduced device reliability and product lifetime. This is because of the
higher power consumption and die temperatures at high sample rates. Also important for reliability is proper
thermal management, as discussed in Thermal Management.
C
C
couple
couple
CLK+
CLK-
ADC08B3000
Figure 47. Differential Sample Clock Connection
44
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: ADC08B3000
ADC08B3000
www.ti.com
SNAS331M –JUNE 2006–REVISED APRIL 2013
The differential sample clock line should have a differential characteristic impedance of 100Ω and be terminated
at the clock source in that (100Ω) characteristic impedance. The input clock line should be as short and as direct
as possible. The ADC08B3000 clock input is internally terminated with an untrimmed 100Ω resistance.
The clock level is important if the specified dynamic performance is to be met. Insufficient input clock levels will
result in poor noise performance. Excessively high input clock levels could result in poor SFDR performance our
cause a change in the analog input offset voltage. To avoid these problems, keep the input clock level within the
range specified in Converter Electrical Characteristics.
The low and high times of the input clock signal can affect the performance of any A/D Converter. The
ADC08B3000 features a clock duty cycle correction circuit which can maintain performance over a wide range of
input clock duty cycles and over temperature. The ADC will meet its performance specification if the input clock
high and low times are maintained as specified in Converter Electrical Characteristics.
High speed, high performance ADCs such as the ADC08B3000 require a very stable input clock signal with
minimum phase noise or jitter. ADC jitter requirements are defined by the ADC resolution (number of bits),
maximum ADC input frequency and the input signal amplitude relative to the ADC input full scale range. The
maximum jitter (the sum of the jitter from all sources) allowed to prevent a jitter-induced reduction in SNR is
found to be
tJ(MAX) = (VINFSR/VIN(P-P)) x (1/(2(N+1) x π x fIN))
(6)
where tJ(MAX) is the rms total of all jitter sources in seconds, VIN(P-P) is the peak-to-peak analog input signal, VINFSR
is the full-scale range of the ADC, "N" is the ADC resolution in bits and fIN is the maximum input frequency, in
Hertz, at the ADC analog input.
Note that the maximum jitter described above is the Root Sum Square, (RSS), of the jitter from all sources,
including the internal ADC clock jitter, that added by the system to the ADC input clock and input signals and that
added by the ADC itself. Since the effective jitter added by the ADC is beyond user control, the best the user can
do is to keep the sum of the externally added input clock jitter and the jitter added by the analog circuitry to the
analog signal to a minimum.
Synchronizing Multiple ADCs (Manual Sample Clock Phase Adjust)
To facilitate the synchronization of multiple ADC08B3000 chips to achieve net sample rates higher than that
possible with a single device, the ADC08B3000 has a manual clock phase capability. This adjustment is only
possible in the Extended Control Mode and is intended to allow the user to accommodate subtle layout
differences when between multiple ADCs. Register addresses Dh and Eh provide extended mode access to fine
and coarse adjustments. Use of Low Frequency Sample Clock control, (register Eh; bit 10) is not supported while
using manual sample clock phase adjustments.
It should be noted that by just enabling the phase adjust capability (register Eh; bit 15), degradation of dynamic
performance is expected, specifically SFDR. It is intended that very small adjustments are used. That is just a
few counts of the fine adjustment and no adjustment of the coarse adjustment. Larger increases in phase
adjustments will begin to affect SNR and ultimately ENOB. Therefore, the use of coarse phase adjustment
should be minimized in favor of better system design.
It is best, then, to ensure that the proper phase relationships exist between the analog input and clock signals
presented to each of the ADC08B3000s that are synchronized. That is, use as much care in PCB design and
layout that would be used if there were no clock phase adjustment circuitry.
Figure 48 and Figure 49 indicate the typical phase adjustment for the fine and coarse phase adjustments,
respectively.
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
45
Product Folder Links: ADC08B3000
ADC08B3000
SNAS331M –JUNE 2006–REVISED APRIL 2013
www.ti.com
Figure 48. Typical Fine Clock Phase Adjust Range
Figure 49. Typical Coarse Clock Phase Adjust Range
CONTROL PINS
Without the use of the serial interface, six control pins provide a range of possibilities in the operation of the
ADC08B3000 to facilitate its use. These control pins provide Full-Scale Input Range setting, Self Calibration,
Calibration Delay, Output Edge Synchronization choice, and Power Down.
Full-Scale Input Range Setting
The input full-scale range can be selected to be either of two settings with the FSR control input (pin 14) in the
Normal Mode of operation. In the Extended Control Mode, the input full-scale range may be set to any of 512
settings. See REGISTER DESCRIPTION for more information.
Calibration
The ADC08B3000 calibration must be run to achieve specified performance. The calibration procedure is run
upon power-up and can be run any time on command. The calibration procedure is exactly the same whether
there is an input clock present upon power up or if the clock begins some time after application of power. The
calibration procedure is also exactly the same whether it is a power-on calibration or an on-command calibration.
The CalRun output is high while a calibration is in progress.
Power-On Calibration
Power-on calibration begins after a time delay following the application of power. This time delay is determined
by the setting of CalDly. See Calibration Delay.
The calibration process will be not be performed if the CAL pin is high at power up. In this case, the calibration
cycle will not begin until the on-command calibration conditions are met. The ADC08B3000 will function with the
CAL pin held high at power up, but no calibration will be done and performance will be impaired. A manual
calibration, however, may be performed after powering up with the CAL pin high. See On-Command Calibration.
46
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: ADC08B3000
ADC08B3000
www.ti.com
SNAS331M –JUNE 2006–REVISED APRIL 2013
The internal power-on calibration circuitry comes up in an unknown logic state. If the input clock is not running at
power up and the power on calibration circuitry is active, it will hold the analog circuitry in power down and the
power consumption will typically be less than 25 mW. The power consumption will be normal after the clock
starts.
On-Command Calibration
To initiate an on-command calibration, bring the CAL pin high for a minimum of 80 input clock cycles after it has
been low for a minimum of 80 input clock cycles. Holding the CAL pin high upon power up will prevent execution
of power-on calibration until the CAL pin is low for a minimum of 80 input clock cycles, then brought high for a
minimum of another 80 input clock cycles. The calibration cycle will begin 80 input clock cycles after the CAL pin
is thus brought high. The CalRun signal should be monitored to determine when the calibration cycle has
completed.
The minimum tCAL_Land tCAL_H input clock cycle sequence is required to ensure that random noise does not
cause a calibration to begin when it is not desired. As mentioned in Calibration, for best performance a
calibration should be performed 20 seconds or more after power up because and repeated when the operating
temperature changes significantly relative to the specific system design performance requirements. The
suggestion for performing an on-command calibration 20 seconds or more after application of power is because
dynamic performance changes with a large change in die temperature and that temperature is nearly stable
about 20 seconds after application of power. Dynamic performance changes slightly with increasing junction
temperature and can be easily corrected by performing an on-command calibration.
Both the ADC and the input termination resistor are calibrated during a power-on calibration cycle. By default, on-
command calibration includes calibration of the input termination resistor and the ADC. However, since the input
termination resistor changes only slightly with temperature, the user has the option to disable the input
termination resistor trim, once trimmed at power up. The Resistor Trim Disable can be programmed in the
Configuration Register when in the Extended Control mode.
Calibration Delay
The CalDly input (pin 127) is used to select one of two delay times after the application of power to the start of
calibration, as described in Calibration. The calibration delay values allow the power supply to come up and
stabilize before calibration takes place. With no delay or insufficient delay, calibration might begin before the
power supply is stabilized at its operating value and result in non-optimal calibration coefficients. If the PD pin is
high upon power-up, the calibration delay counter will be disabled until the PD pin is brought low. Therefore,
holding the PD pin high during power up will further delay the start of the power-up calibration cycle. The best
setting of the CalDly pin depends upon the power-on settling time of the power supply.
Note that the calibration delay selection is not possible in the Extended Control mode and the short delay time is
used.
Input Termination Resistor Trim
The calibration algorithm also trims the input signal termination resistor. This is essential for proper operation of
the device. Once trimmed upon power-up, however, it is not essential for proper operation of the device. Once
trimmed, however, it is not necessary to trim the resistor at each subsequent calibration. The RTD bit in the
Configuration Register allows the user to disable input resistor trim. It is required that this RTD bit be set to 1b if
the Clock Phase Adjust feature is used.
Output Edge Synchronization
OutEdge is an input available to help latch the converter output data into external circuitry. This pin may make
data capture easier, especially when output clock and data trace lengths are not matched. This pin allows the
user to shift the phase of the Data Ready pins (DRDY1 and DRDY2) with respect to the data outputs. See
Double Data Rate.
Power Down Feature
The Power Down pin (PD) allows the ADC08B3000 to be powered down while the capture buffer is still active so
that it may be read. See Power Down for details on the power down feature.
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
47
Product Folder Links: ADC08B3000
ADC08B3000
SNAS331M –JUNE 2006–REVISED APRIL 2013
www.ti.com
The Capture Buffer, its control pins and digital data outputs remain active in the power down mode, allowing the
user to read the Capture Buffer when the PD is high. Upon return to normal operation, the pipeline will contain
meaningless information and must be flushed.
If the PD input is brought high while a calibration is running, the device will not go into power down until the
calibration sequence is complete. However, if power is applied when the PD input is high, the device will not
begin the calibration sequence until the PD input goes low. If a manual calibration is requested while the device
is powered down, the calibration will not begin at all. That is, the manual calibration input is completely ignored in
the power down state.
THE DIGITAL OUTPUTS
The output format is Offset Binary and the logic is LVCMOS. Accordingly, a full-scale input level with VIN+
positive with respect to VIN− will produce an output code of all ones, a full-scale input level with VIN− positive with
respect to VIN+ will produce an output code of all zeros and when VIN+ and VIN− are equal, the output code will
be 127 or 128.
Since the minimum recommended input clock rate for this ADC is 500 MHz and the ADC08B3000 sample rate is
twice the clock rate, the minimum sample rate is generally 1 Gsps. However, the output can easily be decimated
by two, which effectively reduces the minimum effective sample rate to 500 Msps. This is done by setting the
TPE bit in the Capture Buffer register (address Fh, bit D12) to 1b, setting the clock rate to 500 MHz and using
the output data from only one of the two ports.
The output format is Offset Binary. Accordingly, a full-scale input level with VIN+ positive with respect to VIN- will
produce an output code of all ones, a full-scale input level with VIN- positive with respect to VIN+ will produce an
output code of all zeros and when VIN+ and VIN- are equal, the output code will vary between code 127 and 128.
POWER CONSIDERATIONS
A/D converters draw sufficient transient current to corrupt their own power supplies if not adequately bypassed. A
33 µF capacitor should be placed within an inch (2.5 cm) of the A/D converter power pins and a 0.1 µF capacitor
should be placed as close as possible to each VA pin, preferably within one-half centimeter. Leadless chip
capacitors are preferred because they have low lead inductance.
The VA and VDR supply pins should be isolated from each other to prevent any digital noise from being coupled
into the analog portions of the ADC. A ferrite choke, such as the Bourns FB20009-3B, is recommended between
these supply lines when a common source is used for them.
As is the case with all high speed converters, the ADC08B3000 should be assumed to have little power supply
noise rejection. Any power supply used for digital circuitry in a system where a lot of digital power is being
consumed should not be used to supply power to the ADC08B3000. The ADC supplies should be the same
supply used for other analog circuitry, if not a dedicated supply.
Supply Voltage
The ADC08B3000 is specified to operate with a supply voltage of 1.9V ±0.1V. It is very important to note that,
while this device will function with slightly higher supply voltages, these higher supply voltages may reduce
product lifetime.
No pin should ever have a voltage on it that is in excess of the supply voltage or below ground by more than
150 mV, not even on a transient basis. This can be a problem upon application of power and power shut-down.
Be sure that the supplies to circuits driving any of the input pins, analog or digital, do not come up any faster than
does the voltage at the ADC08B3000 power pins.
The Absolute Maximum Ratings should be strictly observed, even during power up and power down. A power
supply that produces a voltage spike at turn-on and/or turn-off of power can destroy the ADC08B3000. The
circuit of Figure 50 will provide supply overshoot protection.
Many linear regulators will produce output spiking at power-on unless there is a minimum load provided. Active
devices draw very little current until their supply voltages reach a few hundred millivolts. The result can be a turn-
on spike that can destroy the ADC08B3000, unless a minimum load is provided for the supply. The 100Ω resistor
at the regulator output of Figure 50 provides a minimum output current during power-up to ensure there is no
turn-on spiking. Whether a linear or switching regulator is used, it is advisable to provide a slow start circuit to
prevent overshoot of the supply.
48
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: ADC08B3000
ADC08B3000
www.ti.com
SNAS331M –JUNE 2006–REVISED APRIL 2013
In the circuit of Figure 50, an LM317 linear regulator is satisfactory if its input supply voltage is 4V to 5V. If a 3.3V
supply is used, an LM1086 linear regulator is recommended.
Linear
Regulator
1.9V
to ADC
V
IN
+
10 mF
210
110
+
33 mF
100
+
10 mF
Figure 50. Non-Spiking Power Supply
The output drivers should have a supply voltage, VDR, that is within the range specified in Operating Ratings.
This voltage should not exceed the VA supply voltage and should never spike to a voltage greater than (VA +
100mV).
If the power is applied to the device without an input clock signal present, the current drawn by the device might
be below 200 mA. This is because the ADC08B3000 gets reset through clocked logic and its initial state is
unknown. If the reset logic comes up in the "on" state, it will cause most of the analog circuitry to be powered
down, resulting in less than 100 mA of current draw. This current is greater than the power down current
because not all of the ADC is powered down. The device current will be normal after the input clock is
established.
Thermal Management
The ADC08B3000 is capable of impressive speeds and performance at very low power levels for its speed.
However, the power consumption is still high enough to require attention to thermal management. For reliability
reasons, the die temperature should be kept to a maximum of 130°C. That is, TA (ambient temperature) plus
ADC power consumption times θJA (junction to ambient thermal resistance) should not exceed 130°C. This is not
a problem if the ambient temperature is kept to a maximum of +85°C as specified in Operating Ratings and the
exposed pad on the bottom of the package is thermally connected to a large enough copper area of the PC
board.
Please note that the following are general recommendations for mounting exposed pad devices onto a PCB. This
should be considered the starting point in PCB and assembly process development. It is recommended that the
process be developed based upon past experience in package mounting.
The package of the ADC08B3000 has an exposed pad on its back that provides the primary heat removal path
as well as excellent electrical grounding to the printed circuit board. The land pattern design for lead attachment
to the PCB should be the same as for a conventional HLQFP, but the exposed pad must be attached to the
board to remove the maximum amount of heat from the package, as well as to ensure best product parametric
performance.
To maximize the removal of heat from the package, a thermal land pattern must be incorporated on the PC
board within the footprint of the package. The exposed pad of the device must be soldered down to ensure
adequate heat conduction out of the package. The land pattern for this exposed pad should be at least as large
as the 5 x 5 mm of the exposed pad of the package and be located such that the exposed pad of the device is
entirely over that thermal land pattern. This thermal land pattern should be electrically connected to ground. A
clearance of at least 0.5 mm should separate this land pattern from the mounting pads for the package pins.
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
49
Product Folder Links: ADC08B3000
ADC08B3000
SNAS331M –JUNE 2006–REVISED APRIL 2013
www.ti.com
5.0 mm, min
0.25 mm, typ
0.33 mm, typ
1.2 mm, typ
Figure 51. Recommended Package Exposed Pad Land Pattern
Since a large aperture opening may result in poor release, the aperture opening should be subdivided into an
array of smaller openings, similar to the land pattern of Figure 51.
To minimize junction temperature, it is recommended that a simple heat sink be built into the PCB. This is done
by including a copper area of about 2 square inches (6.5 square cm) on the opposite side of the PCB. This
copper area may be plated or solder coated to prevent corrosion, but should not have a conformal coating, which
could provide some thermal insulation. Thermal vias should be used to connect these top and bottom copper
areas. These thermal vias act as "heat pipes" to carry the thermal energy from the device side of the board to the
opposite side of the board where it can be more effectively dissipated. The use of 9 to 16 thermal vias is
recommended.
The thermal vias should be placed on a 1.2 mm grid spacing and have a diameter of 0.30 to 0.33 mm. These
vias should be barrel plated to avoid solder wicking into the vias during the soldering process as this wicking
could cause voids in the solder between the package exposed pad and the thermal land on the PCB. Such voids
could increase the thermal resistance between the device and the thermal land on the board, which would cause
the device to run hotter.
If it is desired to monitor die temperature, a temperature sensor may be mounted on the heat sink area of the
board near the thermal vias. Allow for a thermal gradient between the temperature sensor and the ADC08B3000
die of θJ-PAD times typical power consumption = 2.8 x 1.9 = 5.3°C. Allowing for 6.3°C, including some margin for
temperature drop from the pad to the temperature sensor, then, would mean that maintaining a maximum pad
temperature reading of 123.7°C will ensure that the die temperature does not exceed 130°C, assuming that the
exposed pad of the ADC08B3000 is properly soldered down and the thermal vias are adequate. (The inaccuracy
of the temperature sensor is additional to the above calculation).
LAYOUT AND GROUNDING
Proper grounding and proper routing of all signals are essential to ensure optimum performance. A single ground
plane should be used instead of splitting the ground plane into analog and digital areas.
Since digital switching transients are composed largely of high frequency components, the skin effect tells us that
total ground plane copper weight will have little effect upon the logic-generated noise. Total surface area is more
important than is total ground plane volume. Coupling between the typically noisy digital circuitry and the
sensitive analog circuitry can lead to poor performance that may seem impossible to isolate and remedy. The
solution is to keep the analog circuitry well separated from the digital circuitry.
High power digital components should not be located on or near any linear component or power plane that
services analog or mixed signal components as the resulting common return current path could cause fluctuation
in the analog input “ground” return of the ADC, resulting in excessive noise in the conversion result.
50
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: ADC08B3000
ADC08B3000
www.ti.com
SNAS331M –JUNE 2006–REVISED APRIL 2013
Generally, we assume that analog and digital lines should cross each other at 90° to avoid getting digital noise
into the analog path. In high frequency systems, however, avoid crossing analog and digital lines altogether. The
input clock lines should be isolated from ALL other lines, analog AND digital. The generally accepted 90°
crossing should be avoided as even a little coupling can cause problems at high frequencies. Best performance
at high frequencies is obtained with a short, straight signal path.
The analog input should be isolated from other signal traces to avoid coupling of spurious signals into the input.
This is especially important with the low level drive required of the ADC08B3000. Any external component (e.g.,
a filter capacitor) connected between the converter's input and ground should be connected to a very clean point
in the ground plane. All analog circuitry (input amplifiers, filters, etc.) should be separated from any digital
components.
DYNAMIC PERFORMANCE
The ADC08B3000 is a.c. tested and its dynamic performance is ensured. To meet the published specifications
and avoid jitter-induced noise, the clock source driving the CLK input must exhibit low rms jitter. The allowable
jitter is a function of the input frequency and the input signal level, as described in THE SAMPLE CLOCK INPUT.
It is good practice to keep the ADC input clock line as short as possible, to keep it well away from any other
signals and to treat it as a transmission line. Other signals can introduce jitter into the input clock signal. The
clock signal can also introduce noise into the analog path if not isolated from that path.
Best dynamic performance is obtained when the exposed pad at the back of the package has a good connection
to ground. This is because this path from the die to ground is of lower impedance than offered by the package
pins.
USING THE SERIAL INTERFACE
The ADC08B3000 may be operated in the non-extended control (non-Serial Interface) mode or in the extended
control mode. Table 15 and Table 16, below, describe the functions of pins 3, 4, 14 and 127 in the non-extended
control mode and the extended control mode, respectively.
Non-Extended Control Mode Operation
Non-extended control mode operation means that the Serial Interface is not active and all controllable functions
are controlled with various pin settings. That is, the output voltage swing, full-scale range and output edge
selections are all controlled with pin settings. The non-extended control mode is used by setting pin 14 high or
low, as opposed to letting it float. Table 15 indicates the pin functions of the ADC08B3000 in the non-extended
control mode.
Table 15. Non-Extended Control Mode Operation (Pin 14 High or Low)
Pin
4
Low
High
Floating
DDR
OutEdge = Neg
600 mVP-P input range
CalDly Low
OutEdge = Pos
810 mVP-P input range
CalDly High
14
Extended Control Mode
Serial Interface Enable
127
Pin 4 can be high or low or can be left floating in the non-extended control mode. In the non-extended control
mode, pin 4 high or low defines the edge at which the output data transitions. See NORMAL/EXTENDED
CONTROL for more information. If this pin is floating, the output clock (DRDY) is a DDR (Double Data Rate)
clock (see Double Data Rate) and the output edge synchronization is irrelevant since data is clocked out on both
DRDY edges.
If pin 127 is high or low in the non-extended control mode, if sets the calibration delay time. If pin 14 is floating,
the calibration delay is the short one and pin 127 acts as the enable pin for the serial interface input.
Table 16. Extended Control Mode Operation (Pin 14 Floating)
Pin
3
Function
SCLK (Serial Clock)
4
SDATA (Serial Data)
SCS (Serial Interface Select)
127
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
51
Product Folder Links: ADC08B3000
ADC08B3000
SNAS331M –JUNE 2006–REVISED APRIL 2013
www.ti.com
COMMON APPLICATION PITFALLS
Failure to write all register locations when using extended control mode. When using the serial interface, all
six address locations must be written at least once with the default or desired values before calibration and
subsequent use of the ADC.
Driving the inputs (analog or digital) beyond the power supply rails. For device reliability, no input should go
more than 150 mV below the ground pins or 150 mV above the supply pins. Exceeding these limits on even a
transient basis may not only cause faulty or erratic operation, but may impair device reliability. It is not
uncommon for high speed digital circuits to exhibit undershoot that goes more than a volt below ground.
Controlling the impedance of high speed lines and terminating these lines in their characteristic impedance
should control overshoot.
Care should be taken not to overdrive the inputs of the ADC08B3000. Such practice may lead to conversion
inaccuracies and even to device damage.
Incorrect analog input common mode voltage in the d.c. coupled mode. As discussed in The Analog Inputs
and THE ANALOG INPUT, the Input common mode voltage must remain within 50 mV of the VCMO output, which
has a variability with temperature that must also be tracked. Distortion performance will be degraded if the input
common mode voltage is more than 50 mV from VCMO
.
Using an inadequate amplifier to drive the analog input. Use care when choosing a high frequency amplifier
to drive the ADC08B3000 as many high speed amplifiers will have higher distortion than will the ADC08B3000,
resulting in overall system performance degradation.
Driving the VBG pin to change the reference voltage. As mentioned in THE REFERENCE VOLTAGE, the
reference voltage is intended to be fixed to provide one of two different full-scale values in the Normal Mode, or a
range of full-scale values in the Extended Control Mode. The reference can not be changed by driving the
VBG pin, which should not driven.
Driving the clock input with an excessively high level signal. As described in THE SAMPLE CLOCK INPUT,
the ADC input clock level should not exceed the level described in Operating Ratings or the input offset could
change and a degradation of SFDR and SNR could result.
Inadequate input clock levels. As described in THE SAMPLE CLOCK INPUT, insufficient input clock levels can
result in poor performance.
Using a clock source with excessive jitter, using an excessively long input clock signal trace, or having
other signals coupled to the input clock signal trace. Any of these will cause the sampling interval to vary,
causing excessive output noise and a reduction in SNR performance.
Driving an LVCMOS input with LVPECL. The common mode voltage of LVPECL is too high, so the
ADC08B3000 may not properly interpret the input, so recognition of the intended function may be marginal,
intermittent, or non-existent.
Accessing the internal registers while a calibration is in process. As indicated in Calibration and THE
SERIAL INTERFACE, the internal registers (via the serial port) should not be accessed during calibration. Doing
so will impair the performance of the device until it is re-calibrated correctly.
Failure to strictly observe ADCCLK_RST set-up and hold times. The deassertion edge of the ADCCLK_RST
pulse must observe the specified setup and hold times (tSR, tSH). See MULTIPLE ADC SYNCHRONIZATION.
Allowing for timing uncertainty in this timing is also important.
Failure to provide adequate heat removal. As described in Thermal Management, it is important to provide
adequate heat removal to ensure device reliability. This can be done either with adequate air flow or the use of a
simple heat sink built into the board. The backside pad should be grounded for best performance.
52
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: ADC08B3000
ADC08B3000
www.ti.com
SNAS331M –JUNE 2006–REVISED APRIL 2013
REVISION HISTORY
Changes from Revision L (April 2013) to Revision M
Page
•
Changed layout of National Data Sheet to TI format .......................................................................................................... 52
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
53
Product Folder Links: ADC08B3000
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
ADC08B3000CIYB/NOPB
ACTIVE
HLQFP
NNB
128
60
RoHS & Green
SN
Level-3-260C-168 HR
-40 to 85
ADC08B3000
CIYB
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Jun-2023
TRAY
L - Outer tray length without tabs
KO -
Outer
tray
height
W -
Outer
tray
width
Text
P1 - Tray unit pocket pitch
CW - Measurement for tray edge (Y direction) to corner pocket center
CL - Measurement for tray edge (X direction) to corner pocket center
Chamfer on Tray corner indicates Pin 1 orientation of packed units.
*All dimensions are nominal
Device
Package Package Pins SPQ Unit array
Max
matrix temperature
(°C)
L (mm)
W
K0
P1
CL
CW
Name
Type
(mm) (µm) (mm) (mm) (mm)
ADC08B3000CIYB/
NOPB
NNB
HLQFP
128
60
5 X 12
150
322.6 135.9 7620 25.4
17.8 17.55
Pack Materials-Page 1
MECHANICAL DATA
NNB0128A
VNX128A (Rev B)
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023, Texas Instruments Incorporated
相关型号：
ADC08D1000CIYB
DUAL 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP128, MS-026BFB, LQFP-128
ROCHESTER
©2020 ICPDF网 联系我们和版权申明