ADC121C021-Q1 [TI]
具有报警引脚的汽车类 I2C 兼容、12 位模数转换器;
| 型号： | ADC121C021-Q1 |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | 具有报警引脚的汽车类 I2C 兼容、12 位模数转换器 转换器 模数转换器 |
| 文件： | 总45页 (文件大小：1057K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
ADC121C021, ADC121C021Q, ADC121C027
www.ti.com
SNAS415F –JANUARY 2008–REVISED MARCH 2013
ADC121C021/ADC121C021Q/ADC121C027 I2C-Compatible, 12-Bit Analog-to-Digital
Converter with Alert Function
Check for Samples: ADC121C021, ADC121C021Q, ADC121C027
1
FEATURES
DESCRIPTION
•
I2C-Compatible 2-Wire Interface Which
Supports Standard (100kHz), Fast (400kHz),
and High Speed (3.4MHz) Modes
These converters are low-power, monolithic, 12-bit,
analog-to-digital converters (ADCs) that operates
from a +2.7 to 5.5V supply. The converter is based
23
upon
a
successive
approximation
register
•
•
Extended Power Supply Range (+2.7V to
+5.5V)
architecture with an internal track-and-hold circuit that
can handle input frequencies up to 11MHz. These
converters operate from a single supply which also
serves as the reference. The device features an I2C-
compatible serial interface that operates in all three
speed modes, including high speed mode (3.4MHz).
Up to Nine Pin-Selectable Chip Addresses
(VSSOP Only)
•
•
Out-of-Range Alert Function
Automatic Power-Down Mode while Not
Converting
The ADC121C021's Alert feature provides an
interrupt that is activated when the analog input
violates a programmable upper or lower limit value.
The device features an automatic conversion mode,
which frees up the controller and I2C interface. In this
mode, the ADC continuously monitors the analog
input for an "out-of-range" condition and provides an
interrupt if the measured voltage goes out-of-range.
•
•
Very Small 6-Pin SOT and 8-Pin VSSOP
Packages
ADC121C021Q is an Automotive Grade
Product that is AEC-Q100 Grade 2 Qualified
APPLICATIONS
The ADC121C021 comes in two packages: a small 6-
pin SOT package with an alert output, and an 8-pin
VSSOP package with an alert output and two
•
•
•
•
•
•
System Monitoring
Peak Detection
Portable Instruments
Medical Instruments
Test Equipment
Automotive
address selection inputs. The
ADC121C021Q is
available in a 6-pin SOT package. The ADC121C027
comes in a small 6-pin SOT package with an address
selection input. The ADC121C027 provides three pin-
selectable addresses while the 8-pin VSSOP version
of the ADC121C021 provides nine pin-selectable
addresses. Pin-compatible alternatives to the 6-pin
SOT options are available with additional address
options.
KEY SPECIFICATIONS
•
•
•
•
•
Resolution: 12 Bits (No Missing Codes)
Conversion Time: 1µs (Typ)
Normal power consumption using a +3V or +5V
supply is 0.26mW or 0.78mW, respectively. The
automatic power-down feature reduces the power
consumption to less than 1µW while not converting.
Operation over the industrial temperature range of
−40°C to +105°C is ensured. Their low power
consumption and small packages make this family of
ADCs an excellent choice for use in battery operated
equipment.
INL & DNL: ±1 LSB (Max) (Up to 22ksps)
Throughput Rate: 188.9 ksps (Max)
Power Consumption (at 22 ksps)
–
–
3V Supply: 0.26 mW (Typ)
5v Supply: 0.78 mW (Typ)
The ADC121C021 and ADC121C027 are part of a
family of pin-compatible ADCs that also provide 8 and
10 bit resolution. For 8-bit ADCs see the
ADC081C021 and ADC081C027. For 10-bit ADCs
see the ADC101C021 and ADC101C027.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
3
I2C is a registered trademark of Phillips Corporation..
All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2008–2013, Texas Instruments Incorporated
ADC121C021, ADC121C021Q, ADC121C027
SNAS415F –JANUARY 2008–REVISED MARCH 2013
www.ti.com
Pin-Compatible Alternatives (All devices are fully pin and function compatible across resolution)
Resolution
SOT (Alert only) and VSSOP
SOT (Addr only)
ADC121C027
ADC101C027
ADC081C027
12-bit
ADC121C021
10-bit
ADC101C021
8-bit
ADC081C021
Connection Diagrams
VA
VA
1
2
3
6
5
4
1
2
3
6
5
4
SCL
1
2
8
7
SDA
GND
ADR1
VA
SDA
SDA
SCL
ALERT
SCL
GND
VIN
GND
VIN
ADR0
VIN
3
4
6
5
ALERT
ADDR
ADC121C027
ADC121C021
ADC121C021/ADC121C021Q
Figure 1. 6-Pin SOT
See DDC Package
Figure 2. 6-Pin SOT
See DDC Package
Figure 3. 8-Pin VSSOP
See DGK Package
Block Diagram
V
V
IN
A
ADC121C021/
ADC121C027
REF
Oscillator
12-Bit
Successive
Approximation
ADC
T/H
Conversion Result
Highest Conversion
Lowest Conversion
Configuration
Pointer
Register
and
Decode
Logic
Alert Status
Hysteresis
High Limit
Low Limit
Alert
Set-Point
Comparator
ALERT*
SDA
SCL
I2C Serial Interface
ADDR*
GND
* Note: The ADC121C021 has the ALERT pin but no ADDR pin.
The ADC121C027 has the ADDR pin but no ALERT pin.
2
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: ADC121C021 ADC121C021Q ADC121C027
ADC121C021, ADC121C021Q, ADC121C027
www.ti.com
SNAS415F –JANUARY 2008–REVISED MARCH 2013
PIN DESCRIPTIONS
Symbol
Type
Equivalent Circuit
Description
Power and unbuffered reference voltage. VA must be free of
noise and decoupled to GND.
VA
Supply
GND
VIN
Ground
Ground for all on-chip circuitry.
Analog Input
See Figure 22
Analog input. This signal can range from GND to VA.
Alert output. Can be configured as active high or active low.
This is an open drain data line that must be pulled to the
supply (VA) with an external pull-up resistor.
ALERT
Digital Output
Digital Input
Serial Clock Input. SCL is used together with SDA to control
the transfer of data in and out of the device. This is an open
drain data line that must be pulled to the supply (VA) with an
external pull-up resistor.
PIN
D1
SCL
Snap
Back
Serial Data bi-directional connection. Data is clocked into or
out of the internal 16-bit register with SCL. This is an open
drain data line that must be pulled to the supply (VA) with an
external pull-up resistor.
GND
Digital
Input/Output
SDA
Tri-level Address Selection Input. Sets Bits A0 & A1 of the
7-bit slave address. (see Table 1)
ADR0
V+
PIN
41.5k
2.1k
Digital Input,
three levels
D1
Snap
Back
Tri-level Address Selection Input. Sets Bits A2 & A3 of the
7-bit slave address. (see Table 1)
ADR1
41.5k
GND
Package Pinouts
VA
1
GND
VIN
ALERT
SCL
SDA
ADR0
ADR1
N/A
N/A
6
ADC121C021, SOT
ADC121C027, SOT
ADC121C021, VSSOP
2
2
7
3
3
4
4
N/A
2
5
5
1
6
6
8
N/A
4
1
5
3
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: ADC121C021 ADC121C021Q ADC121C027
ADC121C021, ADC121C021Q, ADC121C027
SNAS415F –JANUARY 2008–REVISED MARCH 2013
www.ti.com
Absolute Maximum Ratings(1)(2)(3)
Supply Voltage, VA
-0.3V to +6.5V
−0.3V to (VA +0.3V)
−0.3V to 6.5V
±15 mA
Voltage on any Analog Input Pin to GND
Voltage on any Digital Input Pin to GND
Input Current at Any Pin(4)
Package Input Current(4)
±20 mA
Power Dissipation at TA = 25°C
See(5)
HBM
VA, GND, VIN, ALERT, ADDR Pins SDA
CDM
2500V
250V
ESD Susceptibility per JESD22(6)
1250V
HBM
8000V
SDA
MM
400V
HBM
VA, GND, VIN, ALERT, ADDR Pins MM
CDM
2500V
250V
ESD Susceptibility per AEC-Q100(6)
1250V
HBM
2500V
SDA, SCL Pins
MM
250V
Junction Temperature
Storage Temperature
+150°C
−65°C to +150°C
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. For ensured specifications and test conditions, see the
Electrical Characteristics. The ensured specifications apply only for the test conditions listed. Some performance characteristics may
degrade when the device is not operated under the listed test conditions. Operation of the device beyond the maximum Operating
Ratings is not recommended.
(2) All voltages are measured with respect to GND = 0V, unless otherwise specified.
(3) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
(4) When the input voltage at any pin exceeds 5.5V or is less than GND, the current at that pin should be limited per the Absolute Maximum
Ratings. The maximum package input current rating limits the number of pins that can safely exceed the power supplies.
(5) The absolute maximum junction temperature (TJmax) for this device is 150°C. The maximum allowable power dissipation is dictated by
TJmax, the junction-to-ambient thermal resistance (θJA), and the ambient temperature (TA), and can be calculated using the formula
PDMAX = (TJmax − TA) / θJA. The values for maximum power dissipation will be reached only when the device is operated in a severe
fault condition (e.g., when input or output pins are driven beyond the operating ratings, or the power supply polarity is reversed).
(6) Human body model is a 100 pF capacitor discharged through a 1.5 kΩ resistor. Machine model is a 220 pF capacitor discharged
through 0 Ω. Charged device model simulates a pin slowly acquiring charge (such as from a device sliding down the feeder in an
automated assembler) then rapidly being discharged.
4
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: ADC121C021 ADC121C021Q ADC121C027
ADC121C021, ADC121C021Q, ADC121C027
www.ti.com
SNAS415F –JANUARY 2008–REVISED MARCH 2013
Operating Ratings(1)(2)
Operating Temperature Range
Supply Voltage, VA
−40°C ≤ TA ≤ +105°C
+2.7V to 5.5V
0V to VA
Analog Input Voltage, VIN
Digital Input Voltage(3)
Sample Rate
0V to 5.5V
up to 188.9 ksps
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. For ensured specifications and test conditions, see the
Electrical Characteristics. The ensured specifications apply only for the test conditions listed. Some performance characteristics may
degrade when the device is not operated under the listed test conditions. Operation of the device beyond the maximum Operating
Ratings is not recommended.
(2) All voltages are measured with respect to GND = 0V, unless otherwise specified.
(3) The inputs are protected as shown below. Input voltage magnitudes up to 5.5V, regardless of VA, will not cause errors in the conversion
result. For example, if VA is 3V, the digital input pins can be driven with a 5V logic device.
I/O
TO INTERNAL
CIRCUITRY
GND
Package Thermal Resistances(1)(2)
Package
6-Lead SOT
8-Lead VSSOP
θJA
250°C/W
200°C/W
(1) Soldering process must comply with Reflow Temperature Profile specifications.
(2) Reflow temperature profiles are different for lead-free packages.
Electrical Characteristics
The following specifications apply for VA = +2.7V to +5.5V, GND = 0V, fSCL up to 3.4MHz, fIN = 1kHz for fSCL up to 400kHz,
fIN = 10kHz for fSCL = 3.4MHz unless otherwise noted. Boldface limits apply for TA = TMIN to TMAX: all other limits TA = 25°C
(1)
unless otherwise noted.
Symbol
Parameter
Conditions
Typical(2)
Limits(2)
Units (Limits)
STATIC CONVERTER CHARACTERISTICS
Resolution with No Missing Codes
12
±1
Bits
LSB (max)
LSB
VA = +2.7V to +3.6V, fSCL up to 400kHz(3)
VA = +2.7V to +5.5V. fSCL up to 3.4MHz
±0.5
+1.2
−0.9
+0.5
−0.5
+1.3
−0.9
+0.1
+1.4
-0.8
Integral Non-Linearity (End Point
Method)
INL
LSB
+1
LSB (max)
LSB (min)
LSB
VA = +2.7V to +3.6V, fSCL up to 400kHz(3)
−0.9
DNL
Differential Non-Linearity
VA = +2.7V to +5.5V, fSCL up to 3.4MHz
LSB
VA = +2.7V to +3.6V, fSCL up to 400kHz(3)
VA = +2.7V to +5.5V. fSCL up to 3.4MHz
±1.6
±6
LSB (max)
LSB
VOFF
GE
Offset Error
Gain Error
LSB (max)
(1) To ensure accuracy, it is required that VA be well bypassed and free of noise.
(2) Typical figures are at TJ = 25°C, and represent most likely parametric norms. Test limits are specified to TI's AOQL (Average Outgoing
Quality Level).
(3) The ADC will meet Minimum/Maximum specifications for fSCL up to 3.4MHz and VA = 2.7V to 3.6V when operating in the Quiet Interface
Mode (See Quiet Interface Mode).
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: ADC121C021 ADC121C021Q ADC121C027
ADC121C021, ADC121C021Q, ADC121C027
SNAS415F –JANUARY 2008–REVISED MARCH 2013
www.ti.com
Electrical Characteristics (continued)
The following specifications apply for VA = +2.7V to +5.5V, GND = 0V, fSCL up to 3.4MHz, fIN = 1kHz for fSCL up to 400kHz,
fIN = 10kHz for fSCL = 3.4MHz unless otherwise noted. Boldface limits apply for TA = TMIN to TMAX: all other limits TA = 25°C
unless otherwise noted. (1)
Symbol
Parameter
Conditions
Typical(2)
Limits(2)
11.3
70.4
−78
Units (Limits)
DYNAMIC CONVERTER CHARACTERISTICS
VA = +2.7V to +3.6V
11.7
11.5
72.5
71
Bits (min)
Bits (min)
dB (min)
dB (min)
dB (max)
dB (max)
dB (min)
dB (min)
dB (min)
dB (min)
ENOB
SNR
Effective Number of Bits
VA = +3.6V to +5.5V
VA = +2.7V to +3.6V
VA = +3.6V to +5.5V
VA = +2.7V to +3.6V
VA = +3.6V to +5.5V
VA = +2.7V to +3.6V
VA = +3.6V to +5.5V
VA = +2.7V to +3.6V
VA = +3.6V to +5.5V
Signal-to-Noise Ratio
−92
−87
72.6
71
THD
Total Harmonic Distortion
Signal-to-Noise Plus Distortion Ratio
Spurious-Free Dynamic Range
70
SINAD
SFDR
90
76
87
VA = +3.0V,
fa = 1.035 kHz, fb = 1.135 kHz
−89
−91
−88
−88
dB
dB
dB
dB
Intermodulation Distortion, Second
Order Terms (IMD2)
VA = +5.0V,
fa = 1.035 kHz, fb = 1.135 kHz
IMD
VA = +3.0V,
fa = 1.035 kHz, fb = 1.135 kHz
Intermodulation Distortion, Third
Order Terms (IMD3)
VA = +5.0V,
fa = 1.035 kHz, fb = 1.135 kHz
VA = +3.0V
VA = +5.0V
8
MHz
MHz
FPBW
Full Power Bandwidth (−3dB)
11
ANALOG INPUT CHARACTERISTICS
VIN
Input Range
DC Leakage Current(4)
0 to VA
V
µA (max)
pF
IDCL
±1
Track Mode
Hold Mode
30
3
CINA
Input Capacitance
pF
SERIAL INTERFACE INPUT CHARACTERISTICS (SCL, SDA)
VIH
VIL
Input High Voltage
Input Low Voltage
Input Current(4)
0.7 x VA
0.3 x VA
±1
V (min)
V (max)
µA (max)
pF
IIN
CIN
Input Pin Capacitance
Input Hysteresis
3
VHYST
0.1 x VA
V (min)
ADDRESS SELECTION INPUT CHARACTERISTICS (ADDR)
VIH
VIL
IIN
Input High Voltage
Input Low Voltage
Input Current(4)
VA - 0.5V
0.5
V (min)
V (max)
µA (max)
±1
LOGIC OUTPUT CHARACTERISTICS, OPEN-DRAIN (SDA, ALERT)
ISINK = 3 mA
0.4
0.6
V (max)
V (max)
VOL
IOZ
Output Low Voltage
ISINK = 6 mA
High Impedance Output Leakage
Current(4)
±1
µA (max)
Output Coding
Straight (Natural) Binary
(4) This parameter is ensured by design and/or characterization and is not tested in production.
6
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: ADC121C021 ADC121C021Q ADC121C027
ADC121C021, ADC121C021Q, ADC121C027
www.ti.com
SNAS415F –JANUARY 2008–REVISED MARCH 2013
Electrical Characteristics (continued)
The following specifications apply for VA = +2.7V to +5.5V, GND = 0V, fSCL up to 3.4MHz, fIN = 1kHz for fSCL up to 400kHz,
fIN = 10kHz for fSCL = 3.4MHz unless otherwise noted. Boldface limits apply for TA = TMIN to TMAX: all other limits TA = 25°C
unless otherwise noted. (1)
Symbol
POWER REQUIREMENTS
Supply Voltage Minimum
Supply Voltage Maximum
Continuous Operation Mode -- 2-wire interface active.
Parameter
Conditions
Typical(2)
Limits(2)
Units (Limits)
2.7
5.5
V (min)
V (max)
VA
VA = 2.7V to 3.6V
0.08
0.16
0.37
0.74
0.26
0.78
1.22
3.67
0.14
0.30
0.55
0.99
mA (max)
mA (max)
mA (max)
mA (max)
mW
fSCL=400kHz
fSCL=3.4MHz
fSCL=400kHz
fSCL=3.4MHz
VA = 4.5V to 5.5V
VA = 2.7V to 3.6V
VA = 4.5V to 5.5V
VA = 3.0V
IN
Supply Current
VA = 5.0V
mW
PN
Power Consumption
VA = 3.0V
mW
VA = 5.0V
mW
Automatic Conversion Mode -- 2-wire interface stopped and quiet (SCL = SDA = VA). fSAMPLE = TCONVERT * 32
VA = 2.7V to 3.6V
VA = 4.5V to 5.5V
VA = 3.0V
0.41
0.78
1.35
3.91
0.59
1.2
mA (max)
mA (max)
mW
IA
Supply Current
PA
Power Consumption
VA = 5.0V
mW
Power Down Mode (PD1) -- 2-wire interface stopped and quiet. (SCL = SDA = VA).
IPD1
Supply Current
0.1
0.5
0.2
0.9
µA (max)
µW (max)
See(5)
PPD1
Power Consumption
Power Down Mode (PD2) -- 2-wire interface active. Master communicating with a different device on the bus.
VA = 2.7V to 3.6V
VA = 4.5V to 5.5V
VA = 2.7V to 3.6V
VA = 4.5V to 5.5V
VA = 3.0V
13
27
45
80
µA (max)
µA (max)
µA (max)
µA (max)
mW
fSCL=400kHz
fSCL=3.4MHz
fSCL=400kHz
fSCL=3.4MHz
IPD2
Supply Current
89
150
250
168
0.04
0.14
0.29
0.84
VA = 5.0V
mW
PPD2
Power Consumption
VA = 3.0V
mW
VA = 5.0V
mW
(5) This parameter is ensured by design and/or characterization and is not tested in production.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: ADC121C021 ADC121C021Q ADC121C027
ADC121C021, ADC121C021Q, ADC121C027
SNAS415F –JANUARY 2008–REVISED MARCH 2013
www.ti.com
A.C. and Timing Characteristics
The following specifications apply for VA = +2.7V to +5.5V. Boldface limits apply for TMIN ≤ TA ≤ TMAX and all other limits are
at TA = 25°C, unless otherwise specified.
Units
(Limits)
Symbol
Parameter
Conditions(1)
Typical(2)
Limits(2)
CONVERSION RATE
Conversion Time
1
µs
fSCL = 100kHz
fSCL = 400kHz
fSCL = 1.7MHz
fSCL = 3.4MHz
5.56
22.2
94.4
188.9
ksps
ksps
ksps
ksps
fCONV
Conversion Rate
DIGITAL TIMING SPECS (SCL, SDA)
Standard Mode
Fast Mode
High Speed Mode, Cb = 100pF
High Speed Mode, Cb = 400pF
100
400
3.4
1.7
kHz (max)
kHz (max)
MHz (max)
MHz (max)
fSCL
Serial Clock Frequency
SCL Low Time
Standard Mode
Fast Mode
High Speed Mode, Cb = 100pF
High Speed Mode, Cb = 400pF
4.7
1.3
160
320
us (min)
us (min)
ns (min)
ns (min)
tLOW
Standard Mode
Fast Mode
High Speed Mode, Cb = 100pF
High Speed Mode, Cb = 400pF
4.0
0.6
60
us (min)
us (min)
ns (min)
ns (min)
tHIGH
SCL High Time
120
Standard Mode
Fast Mode
High Speed Mode
250
100
10
ns (min)
ns (min)
ns (min)
tSU;DAT
Data Setup Time
0
3.45
us (min)
us (max)
Standard Mode(3)
0
0.9
us (min)
us (max)
Fast Mode(3)
tHD;DAT
Data Hold Time
0
70
ns (min)
ns (max)
High Speed Mode, Cb = 100pF
High Speed Mode, Cb = 400pF
0
150
ns (min)
ns (max)
Standard Mode
Fast Mode
High Speed Mode
4.7
0.6
160
us (min)
us (min)
ns (min)
Setup time for a start or a repeated
start condition
tSU;STA
Standard Mode
Fast Mode
High Speed Mode
4.0
0.6
160
us (min)
us (min)
ns (min)
Hold time for a start or a repeated start
condition
tHD;STA
Bus free time between a stop and start Standard Mode
4.7
1.3
us (min)
us (min)
tBUF
condition
Fast Mode
Standard Mode
Fast Mode
High Speed Mode
4.0
0.6
160
us (min)
us (min)
ns (min)
tSU;STO
Setup time for a stop condition
Standard Mode
1000
ns (max)
20+0.1Cb
300
ns (min)
ns (max)
Fast Mode
trDA
Rise time of SDA signal
10
80
ns (min)
ns (max)
High Speed Mode, Cb = 100pF
High Speed Mode, Cb = 400pF
20
160
ns (min)
ns (max)
(1) Cb refers to the capacitance of one bus line. Cb is expressed in pF units.
(2) Typical figures are at TJ = 25°C, and represent most likely parametric norms. Test limits are specified to TI's AOQL (Average Outgoing
Quality Level).
(3) The ADC121C021 will provide a minimum data hold time of 300ns to comply with the I2C Specification.
8
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: ADC121C021 ADC121C021Q ADC121C027
ADC121C021, ADC121C021Q, ADC121C027
www.ti.com
SNAS415F –JANUARY 2008–REVISED MARCH 2013
A.C. and Timing Characteristics (continued)
The following specifications apply for VA = +2.7V to +5.5V. Boldface limits apply for TMIN ≤ TA ≤ TMAX and all other limits are
at TA = 25°C, unless otherwise specified.
Units
(Limits)
Symbol
Parameter
Conditions(1)
Standard Mode
Typical(2)
Limits(2)
250
ns (max)
20+0.1Cb
250
ns (min)
ns (max)
Fast Mode
tfDA
Fall time of SDA signal
10
80
ns (min)
ns (max)
High Speed Mode, Cb = 100pF
20
160
ns (min)
ns (max)
High Speed Mode, Cb = 400pF
Standard Mode
1000
ns (max)
20+0.1Cb
300
ns (min)
ns (max)
Fast Mode
trCL
trCL1
tfCL
Rise time of SCL signal
10
40
ns (min)
ns (max)
High Speed Mode, Cb = 100pF
20
80
ns (min)
ns (max)
High Speed Mode, Cb = 400pF
Standard Mode
1000
ns (max)
20+0.1Cb
300
ns (min)
ns (max)
Fast Mode
Rise time of SCL signal after a
repeated start condition and after an
acknowledge bit.
10
80
ns (min)
ns (max)
High Speed Mode, Cb = 100pF
20
160
ns (min)
ns (max)
High Speed Mode, Cb = 400pF
Standard Mode
300
ns (max)
20+0.1Cb
300
ns (min)
ns (max)
Fast Mode
Fall time of a SCL signal
10
40
ns (min)
ns (max)
High Speed Mode, Cb = 100pF
High Speed Mode, Cb = 400pF
20
80
ns (min)
ns (max)
Capacitive load for each bus line (SCL
and SDA)
Cb
400
pF (max)
Fast Mode
High Speed Mode
50
10
ns (max)
ns (max)
tSP
Pulse Width of spike suppressed(4)
(4) Spike suppression filtering on SCL and SDA will suppress spikes that are less than the indicated width.
Timing Diagrams
SDA
t
BUF
t
t
LOW
t
f
HD;STA
t
r
t
t
SP
t
f
r
SCL
t
t
HD;STA
SU;STA
t
SU;STO
t
HIGH
t
t
SU;DAT
HD;DAT
STOP START
START
REPEATED
START
Figure 4. Serial Timing Diagram
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: ADC121C021 ADC121C021Q ADC121C027
ADC121C021, ADC121C021Q, ADC121C027
SNAS415F –JANUARY 2008–REVISED MARCH 2013
www.ti.com
Specification Definitions
ACQUISITION TIME is the time required for the ADC to acquire the input voltage. During this time, the hold
capacitor is charged by the input voltage.
APERTURE DELAY is the time between the start of a conversion and the time when the input signal is internally
acquired or held for conversion.
CONVERSION TIME is the time required, after the input voltage is acquired, for the ADC to convert the input
voltage to a digital word.
DIFFERENTIAL NON-LINEARITY (DNL) is the measure of the maximum deviation from the ideal step size of 1
LSB.
EFFECTIVE NUMBER OF BITS (ENOB, or EFFECTIVE BITS) is another method of specifying Signal-to-Noise
and Distortion or SINAD. ENOB is defined as (SINAD - 1.76) / 6.02 and says that the converter is equivalent to a
perfect ADC of this (ENOB) number of bits.
FULL POWER BANDWIDTH is a measure of the frequency at which the reconstructed output fundamental
drops 3 dB below its low frequency value for a full scale input.
GAIN ERROR is the deviation of the last code transition (111...110) to (111...111) from the ideal (VREF - 1.5
LSB), after adjusting for offset error.
INTEGRAL NON-LINEARITY (INL) is a measure of the deviation of each individual code from a line drawn from
negative full scale (½ LSB below the first code transition) through positive full scale (½ LSB above the last code
transition). The deviation of any given code from this straight line is measured from the center of that code value.
INTERMODULATION DISTORTION (IMD) is the creation of additional spectral components as a result of two
sinusoidal frequencies being applied to an individual ADC input at the same time. It is defined as the ratio of the
power in both the second and the third order intermodulation products to the power in one of the original
frequencies. Second order products are fa ± fb, where fa and fb are the two sine wave input frequencies. Third
order products are (2fa ± fb) and (fa ± 2fb). IMD is usually expressed in dB.
MISSING CODES are those output codes that will never appear at the ADC output. The ADC121C021 is
ensured not to have any missing codes.
OFFSET ERROR is the deviation of the first code transition (000...000) to (000...001) from the ideal (i.e. GND +
0.5 LSB).
SIGNAL TO NOISE RATIO (SNR) is the ratio, expressed in dB, of the rms value of the input signal to the rms
value of the sum of all other spectral components below one-half the sampling frequency, not including
harmonics or d.c.
SIGNAL TO NOISE PLUS DISTORTION (S/N+D or SINAD) Is the ratio, expressed in dB, of the rms value of the
input signal to the rms value of all of the other spectral components below half the clock frequency, including
harmonics but excluding d.c.
SPURIOUS FREE DYNAMIC RANGE (SFDR) is the difference, expressed in dB, between the desired signal
amplitude to the amplitude of the peak spurious spectral component, where a spurious spectral component is
any signal present in the output spectrum that is not present at the input and may or may not be a harmonic.
10
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: ADC121C021 ADC121C021Q ADC121C027
ADC121C021, ADC121C021Q, ADC121C027
www.ti.com
SNAS415F –JANUARY 2008–REVISED MARCH 2013
TOTAL HARMONIC DISTORTION (THD) is the ratio, expressed in dBc, of the rms total of the first n harmonic
components at the output to the rms level of the input signal frequency as seen at the output. THD is calculated
as
2
2
A
+ L + A
f2
Fn
THD = 20 x log
10
2
A
f1
(1)
where Af1 is the RMS power of the input frequency at the output and Af2 through Afn are the RMS power in the
first n harmonic frequencies.
THROUGHPUT TIME is the minimum time required between the start of two successive conversions. It is the
acquisition time plus the conversion time.
LEAST SIGNIFICANT BIT (LSB) is the bit that has the smallest value or weight of all bits in a word. This value is
LSB = VA / 2n
(2)
where VA is the supply voltage for this product, and "n" is the resolution in bits, which is 12 for the ADC121C021.
MOST SIGNIFICANT BIT (MSB) is the bit that has the largest value or weight of all bits in a word. Its value is
1/2 of VA.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: ADC121C021 ADC121C021Q ADC121C027
ADC121C021, ADC121C021Q, ADC121C027
SNAS415F –JANUARY 2008–REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics
fSCL = 400kHz, fSAMPLE = 22ksps, fIN = 1kHz, VA = 5.0V, TA = +25°C, unless otherwise stated.
INL vs. Code - VA=3V
DNL vs. Code - VA=3V
Figure 5.
Figure 6.
INL vs. Code - VA=5V
DNL vs. Code - VA=5V
Figure 7.
Figure 8.
INL vs. Supply
DNL vs. Supply
Figure 9.
Figure 10.
12
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: ADC121C021 ADC121C021Q ADC121C027
ADC121C021, ADC121C021Q, ADC121C027
www.ti.com
SNAS415F –JANUARY 2008–REVISED MARCH 2013
Typical Performance Characteristics (continued)
fSCL = 400kHz, fSAMPLE = 22ksps, fIN = 1kHz, VA = 5.0V, TA = +25°C, unless otherwise stated.
ENOB vs. Supply
SINAD vs. Supply
Figure 11.
FFT Plot
Figure 12.
FFT Plot
Figure 13.
Figure 14.
Offset Error vs. Temperature
Gain Error vs. Temperature
Figure 15.
Figure 16.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: ADC121C021 ADC121C021Q ADC121C027
ADC121C021, ADC121C021Q, ADC121C027
SNAS415F –JANUARY 2008–REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics (continued)
fSCL = 400kHz, fSAMPLE = 22ksps, fIN = 1kHz, VA = 5.0V, TA = +25°C, unless otherwise stated.
Continuous Operation Supply Current vs. VA
Automatic Conversion Supply Current vs. VA
Figure 17.
Figure 18.
Power Down (PD1) Supply Current vs. VA
Figure 19.
14
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: ADC121C021 ADC121C021Q ADC121C027
ADC121C021, ADC121C021Q, ADC121C027
www.ti.com
SNAS415F –JANUARY 2008–REVISED MARCH 2013
Functional Description
The ADC121C021 is a successive-approximation analog-to-digital converter designed around a charge-
redistribution digital-to-analog converter. Unless otherwise stated, references to the ADC121C021 in this section
will apply to both the ADC121C021 and the ADC121C027.
CONVERTER OPERATION
Simplified schematics of the ADC121C021 in both track and hold operation are shown in Figure 20 and
Figure 21 respectively. In Figure 20, the ADC121C021 is in track mode. SW1 connects the sampling capacitor to
the analog input channel, and SW2 equalizes the comparator inputs. The ADC is in this state for approximately
0.4µs at the beginning of every conversion cycle, which begins at the ACK fall of SDA. Conversions occur when
the conversion result register is read and when the ADC is in automatic conversion mode (see Automatic
Conversion Mode).
Figure 21 shows the ADC121C021 in hold mode. SW1 connects the sampling capacitor to ground and SW2
unbalances the comparator. The control logic then instructs the charge-redistribution DAC to add or subtract
fixed amounts of charge to or from the sampling capacitor until the comparator is balanced. At this time the
digital word supplied to the DAC is also the digital representation of the analog input voltage. This digital word is
stored in the conversion result register and read via the 2-wire interface.
In the Normal (non-Automatic) Conversion mode, a new conversion is started after the previous conversion result
is read. In the Automatic Mode, conversions are started at set intervals, as determined by bits D7 through D5 of
the Configuration Register. The intent of the Automatic mode is to provide a "watchdog" function to ensure that
the input voltage remains within the limits set in the Alert Limit Registers. The minimum and maximum
conversion results can then be read from the Lowest Conversion Register and the Highest Conversion Register,
as described in Internal Registers.
CHARGE
REDISTRIBUTION
V
IN
DAC
SAMPLING
CAPACITOR
SW1
+
-
CONTROL
LOGIC
SW2
AGND
V
A
/2
Figure 20. ADC121C021 in Track Mode
CHARGE
REDISTRIBUTION
DAC
V
IN
SAMPLING
CAPACITOR
SW1
+
-
CONTROL
LOGIC
SW2
AGND
V
/2
A
Figure 21. ADC121C021 in Hold Mode
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: ADC121C021 ADC121C021Q ADC121C027
ADC121C021, ADC121C021Q, ADC121C027
SNAS415F –JANUARY 2008–REVISED MARCH 2013
www.ti.com
ANALOG INPUT
An equivalent circuit for the input of the ADC121C021 is shown in Figure 22. The diodes provide ESD protection
for the analog input. The operating range for the analog input is 0 V to VA. Going beyond this range will cause
the ESD diodes to conduct and may result in erratic operation. For this reason, these diodes should NOT be
used to clamp the input signal.
The capacitor C1 in Figure 22 has a typical value of 3 pF and is mainly the package pin capacitance. Resistor R1
is the on resistance (RON) of the multiplexer and track / hold switch and is typically 500Ω. Capacitor C2 is the
ADC121C021 sampling capacitor, and is typically 30 pF. The ADC121C021 will deliver best performance when
driven by a low-impedance source (less than 100Ω). This is especially important when using the ADC121C021 to
sample dynamic signals. A buffer amplifier may be necessary to limit source impedance. Use a precision op-amp
to maximize circuit performance. Also important when sampling dynamic signals is a band-pass or low-pass filter
to reduce noise at the input.
V
A
C2
30 pF
D1
D2
R1
V
IN
C1
3 pF
Conversion Phase - Switch Open
Track Phase - Switch Closed
Figure 22. Equivalent Input Circuit
The analog input is sampled for eight internal clock cycles, or for typically 400 ns, after the fall of SDA for
acknowledgement. This time could be as long as about 530 ns. The sampling switch opens and the conversion
begins this time after the fall of ACK. This time are typical at room temperature and may vary with temperature.
ADC TRANSFER FUNCTION
The output format of the ADC121C021 is straight binary. Code transitions occur midway between successive
integer LSB values. The LSB width for the ADC121C021 is VA / 4096. The ideal transfer characteristic is shown
in Figure 23. The transition from an output code of 0000 0000 0000 to a code of 0000 0000 0001 is at 1/2 LSB,
or a voltage of VA / 8192. Other code transitions occur at intervals of 1 LSB.
111...111
111...110
111...000
ö
1 LSB = V /4096
A
011...111
000...010
000...001
000...000
+V - 1.5 LSB
A
0.5 LSB
0V
ANALOG INPUT
Figure 23. Ideal Transfer Characteristic
16
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: ADC121C021 ADC121C021Q ADC121C027
ADC121C021, ADC121C021Q, ADC121C027
www.ti.com
SNAS415F –JANUARY 2008–REVISED MARCH 2013
REFERENCE VOLTAGE
The ADC121C021 uses the supply (VA) as the reference, so VA must be treated as a reference. The analog-to-
digital conversion will only be as precise as the reference (VA), so the supply voltage should be free of noise. The
reference should be driven by a low output impedance voltage source.
The Applications section provides recommended ways to drive the ADC reference input appropriately. Refer to
Typical Application Circuit for details.
POWER-ON RESET
An internal power-on reset (POR) occurs when the supply voltage transitions above the power-on reset
threshold. Each of the registers contains a defined value upon POR and this data remains there until any of the
following occurs:
•
•
•
The first conversion is completed, causing the Conversion Result and Status registers to be updated.
A different data word is written to a writable register.
The ADC is powered down.
The internal registers will lose their contents if the supply voltage goes below 2.4V. Should this happen, it is
important that the VA supply be lowered to a maximum of 200mV before the supply is raised again to properly
reset the device and ensure that the ADC performs as specified.
INTERNAL REGISTERS
The ADC121C021 has 8 internal data registers and one address pointer. The registers provide additional ADC
functions such as storing minimum and maximum conversion results, setting alert threshold levels, and storing
data to configure the operation of the device. Figure 24 shows all of the registers and their corresponding
address pointer values. All of the registers are read/write capable except the conversion result register, which is
read-only.
Conversion Result
Pointer = 00000000
Alert Status
Pointer = 00000001
Configuration
Pointer = 00000010
Pointer
Register
Low Limit
Pointer = 00000011
(selects
register to
read from
or write to)
High Limit
Pointer = 00000100
Hysteresis
Pointer = 00000101
Lowest Conversion
Pointer = 00000110
Highest Conversion
Pointer = 00000111
SDA
SCL
2
I C Serial Interface
Figure 24. Register Structure
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links: ADC121C021 ADC121C021Q ADC121C027
ADC121C021, ADC121C021Q, ADC121C027
SNAS415F –JANUARY 2008–REVISED MARCH 2013
www.ti.com
Address Pointer Register
The address pointer determines which of the data registers is accessed by the I2C interface. The first data byte
of every write operation is stored in the address pointer register. This value selects the register that the following
data bytes will be written to or read from. Only the three LSBs of this register are variable. The other bits must
always be written to as zeros. After a power-on reset, the pointer register defaults to all zeros (conversion result
register).
Default Value: 00h
P7
P6
P5
P4
P3
P2
P1
P0
0
0
0
0
0
Register Select
P2
P1
P0
0
REGISTER
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
Conversion Result (read only)
Alert Status (read/write)
1
0
Configuration (read/write)
Low Limit (read/write)
1
0
High Limit (read/write)
1
Hysteresis (read/write)
0
Lowest Conversion (read/write)
Highest Conversion (read/write)
1
Conversion Result Register
This register holds the result of the most recent conversion. In the normal mode, a new conversion is started
whenever this register is read. The conversion result data is in straight binary format with the MSB at D11.
Pointer Address 00h (Read Only)
Default Value: 0000h
D15
D14
D13
D12
D4
D11
D3
D10
D9
D8
D0
Alert Flag
Reserved
Conversion Result [11:8]
D7
D6
D5
D2
D1
Conversion Result [7:0]
Bits
Name
Description
15
Alert Flag
This bit indicates when an alert condition has occurred. When the Alert Bit Enable is set in the
Configuration Register, this bit will be high if either alert flag is set in the Alert Status Register.
Otherwise, this bit is a zero. The I2C controller will typically read the Alert Status register and other data
registers to determine the source of the alert.
14:12
11:0
Reserved
Always reads zeros.
Conversion Result
The Analog-to-Digital conversion result. The Conversion result data is a 12-bit data word in straight
binary format. The MSB is D11.
18
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: ADC121C021 ADC121C021Q ADC121C027
ADC121C021, ADC121C021Q, ADC121C027
www.ti.com
SNAS415F –JANUARY 2008–REVISED MARCH 2013
Alert Status Register
This register indicates if a high or a low threshold has been violated. The bits of this register are active high. That
is, a high indicates that the respective limit has been violated.
Pointer Address 01h (Read/Write)
Default Value: 00h
D7
D6
D5
D4
D3
D2
D1
D0
Over Range
Alert
Under Range
Alert
Reserved
Bits
7:2
1
Name
Description
Always reads zeros. Zeros must be written to these bits.
Reserved
Over Range
Alert Flag
Bit is set to 1 when the measured voltage exceeds the VHIGH limit stored in the programmable VHIGH
limit register. Flag is reset to 0 when one of the following two conditions is met: (1) The controller writes
a one to this bit. (2) The measured voltage decreases below the programmed VHIGH limit minus the
programmed VHYST value (See Figure 27). The alert will only self-clear if the Alert Hold bit is cleared in
the Configuration register. If the Alert Hold bit is set, the only way to clear an over range alert is to write
a zero to this bit.
0
Under Range
Alert Flag
Bit is set to 1 when the measured voltage falls below the VLOW limit stored in the programmable VLOW
limit register. Flag is reset to 0 when one of the following two conditions is met: (1) The controller writes
a one to this bit. (2) The measured voltage increases above the programmed VLOW limit plus the
programmed VHYST value. The alert will only self-clear if the Alert Hold bit is cleared in the
Configuration register. If the Alert Hold bit is set, the only way to clear an under range alert is to write a
zero to this bit.
Configuration Register
Pointer Address 02h (Read/Write)
Default Value: 00h
D7
D6
D5
D4
D3
D2
D1
D0
Cycle Time [2:0]
Alert Hold
Alert Flag Enable
Alert Pin Enable
0
Polarity
Cycle Time[2:0]
Typical
fconvert (ksps)
Conversion
Interval
D7
0
D6
0
D5
0
Automatic Mode Disabled
Tconvert x 32
0
0
0
1
27
0
1
0
Tconvert x 64
13.5
6.7
3.4
1.7
0.9
0.4
0
1
1
Tconvert x 128
1
0
0
Tconvert x 256
1
0
1
Tconvert x 512
1
1
0
Tconvert x 1024
Tconvert x 2048
1
1
1
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Links: ADC121C021 ADC121C021Q ADC121C027
ADC121C021, ADC121C021Q, ADC121C027
SNAS415F –JANUARY 2008–REVISED MARCH 2013
www.ti.com
Bits
Name
Description
7:5
Cycle Time
Configures Automatic Conversion mode. When these bits are set to zeros, the automatic conversion
mode is disabled. This is the case at power-up.
When these bits are set to a non-zero value, the ADC will begin operating in automatic conversion
mode (see Automatic Conversion Mode). The Cycle Time table shows how different values provide
various conversion intervals.
4
Alert Hold
0: Alerts will self-clear when the measured voltage moves within the limits by more than the hysteresis
register value.
1: Alerts will not self-clear and are only cleared when a one is written to the alert high flag or the alert
low flag in the Alert Status register.
3
2
Alert Flag Enable
Alert Pin Enable
0: Disables alert status bit [D15] in the Conversion Result register.
1: Enables alert status bit [D15] in the Conversion Result register.
0: Disables the ALERT output pin. The ALERT output will be high impedance when the pin is disabled.
1: Enables the ALERT output pin.
*This bit does not apply to and is a "don't care" for the ADC121C027.
1
0
Reserved
Polarity
Always reads zeros. Zeros must be written to this bit.
This bit configures the active level polarity of the ALERT output pin.
0: Sets the ALERT pin to active low.
1: Sets the ALERT pin to active high.
*This bit does not apply to and is a "don't care" for the ADC121C027.
VLOW -- Alert Limit Register - Under Range
This register holds the lower limit threshold used to determine the alert condition. If the conversion moves lower
than this limit, a VLOW alert is generated.
Pointer Address 03h (Read/Write)
Default Value: 0000h
D15
D14
D13
D12
D4
D11
D3
D10
D9
D1
D8
D0
Reserved
VLOW Limit [11:8]
D7
D6
D5
D2
VLOW Limit [7:0]
Bits
Name
Description
15:12
11:0
Reserved
VLOW Limit
Always reads zeros. Zeros must be written to these bits.
Lower limit threshold. D11 is MSB.
20
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: ADC121C021 ADC121C021Q ADC121C027
ADC121C021, ADC121C021Q, ADC121C027
www.ti.com
SNAS415F –JANUARY 2008–REVISED MARCH 2013
VHIGH -- Alert Limit Register - Over Range
This register holds the upper limit threshold used to determine the alert condition. If the conversion moves higher
than this limit, a VHIGH alert is generated.
Pointer Address 04h (Read/Write)
Default Value: 0FFFh
D15
D14
D13
D12
D4
D11
D3
D10
D9
D1
D8
D0
Reserved
VHIGH Limit [11:8]
D7
D6
D5
D2
VHIGH Limit [7:0]
Bits
Name
Description
15:12
11:0
Reserved
VHIGH Limit
Always reads zeros. Zeros must be written to these bits.
Upper limit threshold. D11 is MSB.
VHYST -- Alert Hysteresis Register
This register holds the hysteresis value used to determine the alert condition. After a VHIGH or VLOW alert occurs,
the conversion result must move within the VHIGH or VLOW limit by more than this value to clear the alert
condition. Note: If the Alert Hold bit is set in the configuration register, alert conditions will not self-clear.
Pointer Address 05h (Read/Write)
Default Value: 0000h
D15
D14
D13
D12
D4
D11
D3
D10
D9
D1
D8
D0
Reserved
Hysteresis [11:8]
D7
D6
D5
D2
Hysteresis [7:0]
Bits
Name
Description
15:12
11:0
Reserved
Hysteresis
Always reads zeros. Zeros must be written to these bits.
Hysteresis value. D11 is MSB.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
21
Product Folder Links: ADC121C021 ADC121C021Q ADC121C027
ADC121C021, ADC121C021Q, ADC121C027
SNAS415F –JANUARY 2008–REVISED MARCH 2013
www.ti.com
VMIN -- Lowest Conversion Register
This register holds the Lowest Conversion result when in the automatic conversion mode. Each conversion result
is compared against the contents of this register. If the value is lower, it becomes the lowest conversion and
replaces the current value. If the value is higher, the register contents remain unchanged. The lowest conversion
value can be cleared at any time by writing 0FFFh to this register. The value of this register will update
automatically when the automatic conversion mode is enabled, but is NOT updated in the normal mode.
Pointer Address 06h (Read/Write)
Default Value: 0FFFh
D15
D14
D13
D12
D4
D11
D3
D10
D9
D8
D0
Reserved
Lowest Conversion [11:8]
D7
D6
D5
D2
D1
Lowest Conversion [7:0]
Bits
Name
Description
15:12
11:0
Reserved
Always reads zeros. Zeros must be written to these bits.
Lowest conversion result data. D11 is MSB.
Lowest Conversion
VMAX -- Highest Conversion Register
This register holds the Highest Conversion result when in the Automatic mode. Each conversion result is
compared against the contents of this register. If the value is higher, it replaces the previous value. If the value is
lower, the register contents remain unchanged. The highest conversion value can be cleared at any time by
writing 0000h to this register. The value of this register will update automatically when the automatic conversion
mode is enabled, but is NOT updated in the normal mode.
Pointer Address 07h (Read/Write)
Default Value: 0000h
D15
D14
D13
D12
D4
D11
D3
D10
D9
D8
D0
Reserved
Highest Conversion [11:8]
D7
D6
D5
D2
D1
Highest Conversion [7:0]
Bits
Name
Description
15:12
11:0
Reserved
Always reads zeros. Zeros must be written to these bits.
Highest conversion result data. D11 is MSB.
Highest Conversion
22
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: ADC121C021 ADC121C021Q ADC121C027
ADC121C021, ADC121C021Q, ADC121C027
www.ti.com
SNAS415F –JANUARY 2008–REVISED MARCH 2013
SERIAL INTERFACE
The I2C-compatible interface operates in all three speed modes. Standard mode (100kHz) and Fast mode
(400kHz) are functionally the same and will be referred to as Standard-Fast mode in this document. High-Speed
mode (3.4MHz) is an extension of Standard-Fast mode and will be referred to as Hs-mode in this document.
The following diagrams describe the timing relationships of the clock (SCL) and data (SDA) signals. Pull-up
resistors or current sources are required on the SCL and SDA busses to pull them high when they are not being
driven low. A logic zero is transmitted by driving the output low. A logic high is transmitted by releasing the output
and allowing it to be pulled-up externally. The appropriate pull-up resistor values will depend upon the total bus
capacitance and operating speed. The ADC121C021 offers extended ESD tolerance (8kV HBM) for the I2C bus
pins (SCL & SDA) allowing extension of the bus across multiple boards without extra ESD protection.
Basic I2C Protocol
The I2C interface is bi-directional and allows multiple devices to operate on the same bus. The bus consists of
master devices and slave devices which can communicate back and forth over the I2C interface. Master devices
control the bus and are typically microcontrollers, FPGAs, DSPs, or other digital controllers. Slave devices are
controlled by a master and are typically peripheral devices such as the ADC121C021. To support multiple
devices on the same bus, each slave has a unique hardware address which is referred to as the "slave address."
To communicate with a particular device on the bus, the controller (master) sends the slave address and listens
for a response from the slave. This response is referred to as an acknowledge bit. If a slave on the bus is
addressed correctly, it Acknowledges (ACKs) the master by driving the SDA bus low. If the address doesn't
match a device's slave address, it Not-acknowledges (NACKs) the master by letting SDA be pulled high. ACKs
also occur on the bus when data is being transmitted. When the master is writing data, the slave ACKs after
every data byte is successfully received. When the master is reading data, the master ACKs after every data
byte is received to let the slave know it wants to receive another data byte. When the master wants to stop
reading, it NACKs after the last data byte and creates a stop condition on the bus.
All communication on the bus begins with either a Start condition or a Repeated Start condition. The protocol for
starting the bus varies between Standard-Fast mode and Hs-mode. In Standard-Fast mode, the master
generates a Start condition by driving SDA from high to low while SCL is high. In Hs-mode, starting the bus is
more complicated. Please refer to High-Speed (Hs) Mode for the full details of a Hs-mode Start condition.
A Repeated Start is generated to address a different device or register, or to switch between read and write
modes. The master generates a Repeated Start condition by driving SDA low while SCL is high. Following the
Repeated Start, the master sends out the slave address and a read/write bit as shown in Figure 25. The bus
continues to operate in the same speed mode as before the Repeated Start condition.
All communication on the bus ends with a Stop condition. In either Standard-Fast mode or Hs-Mode, a Stop
condition occurs when SDA is pulled high while SCL is high. After a Stop condition, the bus remains idle until a
master generates another Start condition.
Please refer to the Philips I2C® Specification (Version 2.1 Jan, 2000) for a detailed description of the serial
interface.
ACK
MSB
N/ACK
SDA
SCL
MSB
LSB
LSB
R/W
Direction
Bit
7-bit Slave Address
Data Byte
Acknowledge
from the Device
*Acknowledge
or Not-ACK
8
9
8
9
1
2
6
7
1
2
Repeated for the Lower Data Byte
and Additional Data Transfers
START or
REPEATED
START
STOP
*Note: In continuous mode, this bit must be an ACK from
the data receiver. Immediately preceding a STOP
condition, this bit must be a NACK from the master.
Figure 25. Basic Operation.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
23
Product Folder Links: ADC121C021 ADC121C021Q ADC121C027
ADC121C021, ADC121C021Q, ADC121C027
SNAS415F –JANUARY 2008–REVISED MARCH 2013
www.ti.com
Standard-Fast Mode
In Standard-Fast mode, the master generates a start condition by driving SDA from high to low while SCL is
high. The start condition is always followed by a 7-bit slave address and a Read/Write bit. After these 8 bits have
been transmitted by the master, SDA is released by the master and the ADC121C021 either ACKs or NACKs the
address. If the slave address matches, the ADC121C021 ACKs the master. If the address doesn't match, the
ADC121C021 NACKs the master.
For a write operation, the master follows the ACK by sending the 8-bit register address pointer to the ADC. Then
the ADC121C021 ACKs the transfer by driving SDA low. Next, the master sends the upper 8-bits to the
ADC121C021. Then the ADC121C021 ACKs the transfer by driving SDA low. For a single byte transfer, the
master should generate a stop condition at this point. For a 2-byte write operation, the lower 8-bits are sent by
the master. The ADC121C021 then ACKs the transfer, and the master either sends another pair of data bytes,
generates a Repeated Start condition to read or write another register, or generates a Stop condition to end
communication.
A read operation can take place either of two ways:
If the address pointer is pre-set before the read operation, the desired register can be read immediately following
the slave address. In this case, the upper 8-bits of the register, set by the pre-set address pointer, are sent out
by the ADC. For a single byte read operation, the Master sends a NACK to the ADC and generates a Stop
condition to end communication after receiving 8-bits of data. For a 2-Byte read operation, the Master continues
the transmission by sending an ACK to the ADC. Then the ADC sends out the lower 8-bits of the ADC register.
At this point, the master either sends an ACK to receive more data or sends a NACK followed by a Stop or
Repeated Start. If the master sends an ACK, the ADC sends the next data byte, and the read cycle repeats.
If the ADC121C021address pointer needs to be set, the master needs to write to the device and set the address
pointer before reading from the desired register. This type of read requires a start, the slave address, a write bit,
the address pointer, a Repeated Start (if appropriate), the slave address, and a read bit (refer to Figure 30).
Following this sequence, the ADC sends out the upper 8-bits of the register. For a single byte read operation, the
Master must then send a NACK to the ADC and generate a Stop condition to end communication. For a 2-Byte
write operation, the Master sends an ACK to the ADC. Then, the ADC sends out the lower 8-bits of the ADC
register. At this point, the master sends either an ACK to receive more data, or a NACK followed by a Stop or
Repeated Start. If the master sends an ACK, the ADC sends another pair of data bytes, and the read cycle will
repeat. The number of data words that can be read is unlimited.
High-Speed (Hs) Mode
For Hs-mode, the sequence of events to begin communication differs slightly from Standard-Fast mode.
Figure 26 describes this in further detail. Initially, the bus begins running in Standard-Fast mode. The master
generates a Start condition and sends the 8-bit Hs master code (00001XXX) to the ADC121C021. Next, the
ADC121C021 responds with a NACK. Once the SCL line has been pulled to a high level, the master switches to
Hs-mode by increasing the bus speed and generating a second Repeated Start condition (driving SDA low while
SCL is pulled high). At this point, the master sends the slave address to the ADC121C021, and communication
continues as shown above in the "Basic Operation" Diagram (see Figure 25).
When the master generates a Repeated Start condition while in Hs-mode, the bus stays in Hs-mode awaiting the
slave address from the master. The bus continues to run in Hs-mode until a Stop condition is generated by the
master. When the master generates a Stop condition on the bus, the bus must be started in Standard-Fast mode
again before increasing the bus speed and switching to Hs-mode.
24
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: ADC121C021 ADC121C021Q ADC121C027
ADC121C021, ADC121C021Q, ADC121C027
www.ti.com
SNAS415F –JANUARY 2008–REVISED MARCH 2013
NACK
MSB
SDA
SCL
8-bit Master code —00001xxx“
7-bit Slave
Address
Not-Acknowledge
from the Device
8
9
1
2
6
7
1
2
5
Repeated
START
START
Standard-Fast Mode
Hs-Mode
Figure 26. Beginning Hs-Mode Communication
I2C Slave (Hardware) Address
The ADC has a seven-bit hardware address which is also referred to as a slave address. For the VSSOP version
of the ADC121C021, this address is configured by the ADR0 and ADR1 addres selection inputs. For the
ADC121C027, the address is configured by the ADR0 address selection input. ADR0 and ADR1 can be
grounded, left floating, or tied to VA. If desired, ADR0 and ADR1 can be set to VA/2 rather than left floating. The
state of these inputs sets the hardware address that the ADC responds to on the I2C bus (see Table 1). For the
ADC121C021, the hardware address is not pin-configurable and is set to 1010100. The diagrams in
Communicating with the ADC121C021 describes how the I2C controller should address the ADC via the I2C
interface.
Table 1. Slave Addresses
ADC121C027
ADC121C021
ADC121C021
(VSSOP)
Slave Address
[A6 - A0]
(SOT)
(SOT)
ADR0
Floating
ALERT
ADR1
Floating
Floating
Floating
GND
GND
GND
VA
ADR0
Floating
GND
VA
1010000
1010001
1010010
1010100
1010101
1010110
1011000
1011001
1011010
-----------------
-----------------
-----------------
Single Address
-----------------
-----------------
-----------------
-----------------
-----------------
GND
VA
-----------------
-----------------
-----------------
-----------------
-----------------
-----------------
Floating
GND
VA
Floating
GND
VA
VA
VA
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
25
Product Folder Links: ADC121C021 ADC121C021Q ADC121C027
ADC121C021, ADC121C021Q, ADC121C027
SNAS415F –JANUARY 2008–REVISED MARCH 2013
www.ti.com
ALERT FUNCTION
The ALERT function is an "out-of-range" indicator. At the end of every conversion, the measured voltage is
compared to the values in the VHIGH and VLOW registers. If the measured voltage exceeds the value stored in
VHIGH or falls below the value stored in VLOW, an alert condition occurs. The Alert condition is indicated in up to
three places. First, the alert condition always causes either or both of the alert flags in the Alert Status register to
go high. If the measured voltage exceeds the VHIGH limit, the Over Range Alert Flag is set. If the measured
voltage falls below the VLOW limit, the Under Range Alert Flag is set. Second, if the Alert Flag Enable bit is set in
the Configuration register, the alert condition also sets the MSB of the Conversion Result register. Third, if the
Alert Pin Enable bit is set in the Configuration register, the ALERT output becomes active (see Figure 27). The
ALERT output (ADC121C021 only) can be configured as an active high or active low output via the Polarity bit in
the Configuration register. If the Polarity bit is cleared, the ALERT output is configured as active low. If the
Polarity bit is set, the ALERT output is configured as active high.
The Over Range Alert condition is cleared when one of the following two conditions is met:
1. The controller writes a one to the Over Range Alert Flag bit.
2. The measured voltage goes below the programmed VHIGH limit minus the programmed VHYST value and the
Alert Hold bit is cleared in the Configuration register. (see Figure 27). If the Alert Hold bit is set, the alert
condition persists and only clears when a one is written to the Over Range Alert Flag bit.
The Under Range Alert condition is cleared when one of the following two conditions is met:
1. The controller writes a one to the Under Range Alert Flag bit.
2. The measured voltage goes above the programmed VLOW limit plus the programmed VHYST value and the
Alert Hold bit is cleared in the Configuration register. If the Alert Hold bit is set, the alert condition persists
and only clears when a one is written to the Under Range Alert Flag bit.
If the alert condition has been cleared by writing a one to the alert flag while the measured voltage still violates
the VHIGH or VLOW limits, an alert condition will occur again after the completion of the next conversion (see
Figure 28).
Alert conditions only occur if the input voltage exceeds the VHIGH limit or falls below the VLOW limit at the sample-
hold instant. The input voltage can exceed the VHIGH limit or fall below the VLOW limit briefly between conversions
without causing an alert condition.
Measured Voltage
V
V
Limit
HIGH
- V
HIGH
HYST
ALERT pin
(Active Low)
TIME
Figure 27. Alert condition cleared when measured voltage crosses VHIGH - VHYST
Over Range Alert
Flag set to —1“
Measured Voltage
V
V
Limit
HIGH
- V
HIGH
HYST
ALERT pin
(Active Low)
TIME
Figure 28. Alert condition cleared by writing a "1" to the Alert Flag.
26
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: ADC121C021 ADC121C021Q ADC121C027
ADC121C021, ADC121C021Q, ADC121C027
www.ti.com
SNAS415F –JANUARY 2008–REVISED MARCH 2013
AUTOMATIC CONVERSION MODE
The automatic conversion mode configures the ADC to continually perform conversions without receiving "read"
instructions from the controller over the I2C interface. The mode is activated by writing a non-zero value into the
Cycle Time bits - D[7:5] - of the Configuration register (see Configuration Register). Once the ADC121C021
enters this mode, the internal oscillator is always enabled. The ADC's control logic samples the input at the
sample rate set by the cycle time bits. Although the conversion result is not transmitted by the 2-wire interface, it
is stored in the conversion result register and updates the various status registers of the device.
In automatic conversion mode, the out-of-range alert function is active and updates after every conversion. The
ADC can operate independently of the controller in automatic conversion mode. When the input signal goes "out-
of-range", an alert signal is sent to the controller. The controller can then read the status registers and determine
the source of the alert condition. Also, comparison and updating of the VMIN and VMAX registers occurs after every
conversion in automatic conversion mode. The controller can occasionally read the VMIN and/or VMAX registers to
determine the sampled input extremes. These register values persist until the user resets the VMIN and VMAX
registers. These two features are useful in system monitoring, peak detection, and sensing applications.
COMMUNICATING WITH THE ADC121C021
The ADC121C021's data registers are selected by the address pointer (see Address Pointer Register). To
read/write a specific data register, the pointer must be set to that register's address. The pointer is always written
at the beginning of a write operation. When the pointer needs to be updated for a read cycle, a write operation
must precede the read operation to set the pointer address correctly. On the other hand, if the pointer is preset
correctly, a read operation can occur without writing the address pointer register. The following timing diagrams
describe the various read and write operations supported by the ADC.
Reading from a 2-Byte ADC Register
The following diagrams indicate the sequence of actions required for a 2-Byte read from an ADC121C021
Register.
1
9
1
9
1
9
SCL
SDA
A6 A5 A4 A3 A2 A1 A0 R/W
D15 D14 D13 D12 D11 D10 D9 D8
D7 D6 D5 D4 D3 D2 D1 D0
ACK
by
ADC
ACK
by
Master
N/ACK* Stop
Start by
Master
by
by
Master Master
Frame 1
Address Byte
from Master
Frame 2
Data Byte from
ADC
Frame 3
Data Byte from
ADC
Repeat Frames
2 & 3 for
Continuous Mode
*Note: In continuous mode, this bit must be an ACK. Immediately
preceding a STOP condition, this bit must be a NACK.
Figure 29. (a) Typical Read from a 2-Byte ADC Register with Preset Pointer
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
27
Product Folder Links: ADC121C021 ADC121C021Q ADC121C027
ADC121C021, ADC121C021Q, ADC121C027
SNAS415F –JANUARY 2008–REVISED MARCH 2013
www.ti.com
1
9
1
0
9
SCL
SDA
R/W
A6 A5 A4 A3 A2 A1 A0
0
0
0
0
P2 P1 P0
Ack
by
ADC
Ack
by
ADC
Start by
Master
Frame 1
Frame 2
Address Byte
from Master
Pointer Byte
from Master
1
9
1
9
1
9
SCL
(continued)
SDA
(continued)
A6 A5 A4 A3 A2 A1 A0
Repeat
D15 D14 D13 D12 D11 D10 D9 D8
D7 D6 D5 D4 D3 D2 D1 D0
R/W
ACK
by
ADC
ACK
by
Master
N/ACK* Stop
by by
Master Master
Start by
Master
Frame 3
Frame 4
Data Byte from
ADC
Frame 5
Data Byte from
ADC
Address Byte
from Master
Repeat Frames
4 & 5 for
Continuous Mode
*Note: In continuous mode, this bit must be an ACK. Immediately
preceding a STOP condition, this bit must be a NACK.
Figure 30. (b) Typical Pointer Set Followed by Immediate Read of a 2-Byte ADC Register
Reading from a 1-Byte ADC Register
The following diagrams indicate the sequence of actions required for a single Byte read from an ADC121C021
Register.
1
9
1
9
SCL
SDA
A6 A5 A4 A3 A2 A1 A0
D7 D6 D5 D4 D3 D2 D1 D0
R/W
ACK
by
ADC
NACK
by
Master Master
Stop
by
Start by
Master
Frame 1
Address Byte
from Master
Frame 2
Data Byte from
ADC
Figure 31. (a) Typical Read from a 1-Byte ADC Register with Preset Pointer
1
9
1
0
9
SCL
SDA
R/W
A6 A5 A4 A3 A2 A1 A0
0
0
0
0
P2 P1 P0
Ack
by
ADC
Ack
by
ADC
Start by
Master
Frame 1
Frame 2
Address Byte
from Master
Pointer Byte
from Master
1
9
1
9
SCL
(continued)
SDA
(continued)
A6 A5 A4 A3 A2 A1 A0
Repeat
D7 D6 D5 D4 D3 D2 D1 D0
R/W
ACK
by
ADC
NACK
by
Stop
by
Start by
Master
Master Master
Frame 3
Frame 4
Data Byte from
ADC
Address Byte
from Master
Figure 32. (b) Typical Pointer Set Followed by Immediate Read of a 1-Byte ADC Register
28
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: ADC121C021 ADC121C021Q ADC121C027
ADC121C021, ADC121C021Q, ADC121C027
www.ti.com
SNAS415F –JANUARY 2008–REVISED MARCH 2013
Writing to an ADC Register
The following diagrams indicate the sequence of actions required for writing to an ADC121C021 Register.
1
9
1
9
1
9
SCL
SDA
R/W
A6 A5 A4 A3 A2 A1 A0
0
0
0
0
0
P2 P1 P0
D7 D6 D5 D4 D3 D2 D1 D0
Start by
Master
ACK
by
ACK
by
ACK Stop by
by
Master
ADC
ADC
ADC
Frame 1
Address Byte
from Master
Frame 2
Pointer Byte
from Master
Frame 3
Data Byte
from Master
Figure 33. (a) Typical Write to a 1-Byte ADC Register
1
9
1
0
9
SCL
SDA
R/W
A6 A5 A4 A3 A2 A1 A0
0
0
0
0
P2 P1 P0
Ack
by
ADC
Ack
by
ADC
Start by
Master
Frame 1
Frame 2
Address Byte
from Master
Pointer Byte
from Master
1
9
1
9
SCL
(continued)
SDA
(continued)
D15 D14 D13 D12 D11 D10 D9 D8
D7 D6 D5 D4 D3 D2 D1 D0
ACK
by
NACK
by
Stop
by
ADC
Master Master
Frame 3
Data Byte
from Master
Frame 4
Data Byte
from Master
Figure 34. (b) Typical Write to a 2-Byte ADC Register
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
29
Product Folder Links: ADC121C021 ADC121C021Q ADC121C027
ADC121C021, ADC121C021Q, ADC121C027
SNAS415F –JANUARY 2008–REVISED MARCH 2013
www.ti.com
QUIET INTERFACE MODE
To improve performance at High Speed, operate the ADC in Quiet Interface Mode. This mode provides improved
INL and DNL performance in I2C Hs-Mode (3.4MHz). The Quiet Interface mode provides a maximum throughput
rate of 162ksps. Figure 35 describes how to read the conversion result register in this mode. Basically, the
Master needs to release SCL for at least 1µs before the MSB of every upper data byte. The diagram assumes
that the address pointer register is set to its default value.
Quiet Interface mode will only improve INL and DNL performance in Hs-Mode. Standard and Fast mode
performance is unaffected by the Quiet Interface mode.
Interface Delay
tQuiet 8 1us
1
9
1
9
SCL
SDA
R/W
A6 A5 A4 A3 A2 A1 A0
D15 D14 D13 D12 D11 D10 D9 D8
ACK
by
ADC
ACK
by
Master
Start by
Master
Frame 1
Address Byte
from Master
Frame 2
Upper Data Byte
from ADC
Interface Delay
tQuiet 8 1us
1
9
1
9
1
9
SCL
(continued)
SDA
(continued)
D7 D6 D5 D4 D3 D2 D1 D0
D15 D14 D13 D12 D11 D10 D9 D8
D7 D6 D5 D4 D3 D2 D1 D0
ACK
by
ACK
by
NACK
by
Stop
by
Master
Master
Master Master
Frame 3
Lower Data Byte
from ADC
Frame 4
Upper Data Byte
from ADC
Frame 5
Lower Data Byte
from ADC
Repeat Frames
4 and 5 for
Continuous Mode
Figure 35. Reading in Quiet Interface Mode
30
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: ADC121C021 ADC121C021Q ADC121C027
ADC121C021, ADC121C021Q, ADC121C027
www.ti.com
SNAS415F –JANUARY 2008–REVISED MARCH 2013
APPLICATIONS INFORMATION
TYPICAL APPLICATION CIRCUIT
A typical application circuit is shown in Figure 36. The analog supply is bypassed with a capacitor network
located close to the ADC121C021. The ADC uses the analog supply (VA) as its reference voltage, so it is very
important that VA be kept as clean as possible. Due to the low power requirements of the ADC121C021, it is
possible to use a precision reference as a power supply.
The bus pull-up resistors (RP) should be powered by the controller's supply. It is important that the pull-up
resistors are pulled to the same voltage potential as VA. This will ensure that the logic levels of all devices on the
bus are compatible. If the controller's supply is noisy, an appropriate bypass capacitor should be added between
the controller's supply pin and the pull-up resistors. For Hs-mode applications, this bypass capacitance will
improve the accuracy of the ADC.
The value of the pull-up resistors (RP) depends upon the characteristics of each particular I2C bus. The I2C
specification describes how to choose an appropriate value. As a general rule-of-thumb, we suggest using a 1kΩ
resistor for Hs-mode bus configurations and a 5kΩ resistor for Standard or Fast Mode bus configurations.
Depending upon the bus capacitance, these values may or may not be sufficient to meet the timing requirements
of the I2C bus specification. Please see the I2C specification for further information.
Regulated Supply
0.1 mF
4.7 mF
5 kW
R
R
P
P
V
DD
Controller
V
A
INTERRUPT
ALERT
22W
INPUT
V
IN
ADC121C021
SDA
SCL
SDA
SCL
470 pF
GND
Figure 36. Typical Application Circuit
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
31
Product Folder Links: ADC121C021 ADC121C021Q ADC121C027
ADC121C021, ADC121C021Q, ADC121C027
SNAS415F –JANUARY 2008–REVISED MARCH 2013
www.ti.com
BUFFERED INPUT
A buffered input application circuit is shown in Figure 37. The analog input is buffered by a Texas Instruments
LMP7731. The non-inverting amplifier configuration provides a buffered gain stage for a single ended source.
This application circuit is good for single-ended sensor interface. The input must have a DC bias level that keeps
the ADC input signal from swinging below GND or above the supply (+5V in this case).
The LM4132, with its 0.05% accuracy over temperature, is an excellent choice as a reference source for the
ADC121C021.
Unregulated
Supply
LM4132
4.7 mF
0.1 mF
4.7 mF
V
A
+
RS
CS
INPUT
LMP7731
-
V
IN
ADC121C027
SDA
SCL
ADDR
GND
R
1
R
2
Figure 37. Buffered Input Circuit
INTELLIGENT BATTERY MONITOR
The ADC121C021 is easily used as an intelligent battery monitor. The simple circuit shown in Figure 38, uses
the ADC121C021, the LP2980 fixed reference, and a resistor divider to implement an intelligent battery monitor
with a window supervisory feature. The window supervisory feature is implemented by the "out of range" alert
function. When the battery is recharging, the Over Range Alert will indicate that the charging cycle is complete
(see Figure 39). When the battery is nearing depletion, the Under Range Alert will indicate that the battery is low
(see Figure 40).
REF
[LP2980-2.8]
R
Low
Battery
Indicator
V
A
ALERT
ADC121C021
To Controller...
V
IN
SCL
SDA
GND
Figure 38. Intelligent Battery Monitor Circuit
32
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: ADC121C021 ADC121C021Q ADC121C027
ADC121C021, ADC121C021Q, ADC121C027
www.ti.com
SNAS415F –JANUARY 2008–REVISED MARCH 2013
RECHARGE CYCLE
Measured
Battery
Voltage
V
High
Limit
ALERT pin
(Active Low)
TIME
Figure 39. Recharge Cycle
DISCHARGE CYCLE
Measured
Battery
Voltage
V
LOW
Limit
ALERT pin
(Active Low)
TIME
Figure 40. Discharge Cycle
In addition to the window supervisory feature, the ADC121C021 will allow the controller to read the battery
voltage at any time during operation.
The accurate voltage reading and the alert feature will allow a controller to improve the efficiency of a battery-
powered device. During the discharge cycle, the controller can switch to a low-battery mode, safely suspend
operation, or report a precise battery level to the user. During the recharge cycle, the controller can implement an
intelligent recharge cycle, decreasing the charge rate when the battery charge nears capacity.
Trickle Charge Controller
While a battery is discharging, the ADC121C021 can be used to control a trickle charge to keep the battery near
full capacity (see Figure 41). When the alert output is active, the battery will recharge. An intelligent recharge
cycle will prevent over-charging and damaging the battery. With a trickle charge, the battery powered device can
be disconnected from the charger at any time with a full charge.
Measured
Battery Voltage
V +V
LOW HYST
V
LOW
Limit
ALERT pin
(Active Low)
TIME
Figure 41. Trickle Charge
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
33
Product Folder Links: ADC121C021 ADC121C021Q ADC121C027
ADC121C021, ADC121C021Q, ADC121C027
SNAS415F –JANUARY 2008–REVISED MARCH 2013
www.ti.com
LAYOUT, GROUNDING, AND BYPASSING
For best accuracy and minimum noise, the printed circuit board containing the ADC121C021 should have
separate analog and digital areas. The areas are defined by the locations of the analog and digital power planes.
Both of these planes should be located on the same board layer. A single, solid ground plane is preferred if
digital return current does not flow through the analog ground area. Frequently a single ground plane design will
utilize a "fencing" technique to prevent the mixing of analog and digital ground current. Separate ground planes
should only be utilized when the fencing technique is inadequate. The separate ground planes must be
connected in one place, preferably near the ADC121C021. Special care is required to ensure that signals do not
pass over power plane boundaries. Return currents must always have a continuous return path below their
traces.
The ADC121C021 power supply should be bypassed with a 4.7µF and a 0.1µF capacitor as close as possible to
the device with the 0.1µF right at the device supply pin. The 4.7µF capacitor should be a tantalum type and the
0.1µF capacitor should be a low ESL type. The power supply for the ADC121C021 should only be used for
analog circuits.
Avoid crossover of analog and digital signals and keep the clock and data lines on the component side of the
board. The clock and data lines should have controlled impedances.
34
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: ADC121C021 ADC121C021Q ADC121C027
ADC121C021, ADC121C021Q, ADC121C027
www.ti.com
SNAS415F –JANUARY 2008–REVISED MARCH 2013
REVISION HISTORY
Changes from Revision E (March 2013) to Revision F
Page
•
Changed layout of National Data Sheet to TI format .......................................................................................................... 34
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
35
Product Folder Links: ADC121C021 ADC121C021Q ADC121C027
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
ADC121C021CIMK/NOPB
ADC121C021CIMKX/NOPB
ADC121C021CIMM/NOPB
ADC121C021QIMK/NOPB
ADC121C021QIMKX/NOPB
ADC121C027CIMK/NOPB
ADC121C027CIMKX/NOPB
ACTIVE SOT-23-THIN
ACTIVE SOT-23-THIN
DDC
DDC
DGK
DDC
DDC
DDC
DDC
6
6
8
6
6
6
6
1000 RoHS & Green
3000 RoHS & Green
1000 RoHS & Green
1000 RoHS & Green
3000 RoHS & Green
1000 RoHS & Green
3000 RoHS & Green
SN
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-40 to 105
-40 to 105
-40 to 105
-40 to 105
-40 to 105
-40 to 105
-40 to 105
X30C
X30C
X37C
X30Q
X30Q
X31C
X31C
SN
SN
SN
SN
SN
SN
ACTIVE
VSSOP
ACTIVE SOT-23-THIN
ACTIVE SOT-23-THIN
ACTIVE SOT-23-THIN
ACTIVE SOT-23-THIN
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF ADC121C021, ADC121C021-Q1 :
Catalog: ADC121C021
•
Automotive: ADC121C021-Q1
•
NOTE: Qualified Version Definitions:
Catalog - TI's standard catalog product
•
Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
•
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Aug-2022
TAPE AND REEL INFORMATION
REEL DIMENSIONS
TAPE DIMENSIONS
K0
P1
W
B0
Reel
Diameter
Cavity
A0
A0 Dimension designed to accommodate the component width
B0 Dimension designed to accommodate the component length
K0 Dimension designed to accommodate the component thickness
Overall width of the carrier tape
W
P1 Pitch between successive cavity centers
Reel Width (W1)
QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE
Sprocket Holes
Q1 Q2
Q3 Q4
Q1 Q2
Q3 Q4
User Direction of Feed
Pocket Quadrants
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
ADC121C021CIMK/NOPB SOT-23-
THIN
DDC
DDC
DGK
DDC
DDC
DDC
DDC
6
6
8
6
6
6
6
1000
3000
1000
1000
3000
1000
3000
178.0
178.0
178.0
178.0
178.0
178.0
178.0
8.4
8.4
12.4
8.4
8.4
8.4
8.4
3.2
3.2
5.3
3.2
3.2
3.2
3.2
3.2
3.2
3.4
3.2
3.2
3.2
3.2
1.4
1.4
1.4
1.4
1.4
1.4
1.4
4.0
4.0
8.0
4.0
4.0
4.0
4.0
8.0
8.0
12.0
8.0
8.0
8.0
8.0
Q3
Q3
Q1
Q3
Q3
Q3
Q3
ADC121C021CIMKX/
NOPB
SOT-23-
THIN
ADC121C021CIMM/
NOPB
VSSOP
ADC121C021QIMK/NOPB SOT-23-
THIN
ADC121C021QIMKX/
NOPB
SOT-23-
THIN
ADC121C027CIMK/NOPB SOT-23-
THIN
ADC121C027CIMKX/
NOPB
SOT-23-
THIN
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Aug-2022
TAPE AND REEL BOX DIMENSIONS
Width (mm)
H
W
L
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
ADC121C021CIMK/NOPB
SOT-23-THIN
SOT-23-THIN
DDC
DDC
6
6
1000
3000
210.0
210.0
185.0
185.0
35.0
35.0
ADC121C021CIMKX/
NOPB
ADC121C021CIMM/NOPB
ADC121C021QIMK/NOPB
VSSOP
DGK
DDC
DDC
8
6
6
1000
1000
3000
210.0
210.0
210.0
185.0
185.0
185.0
35.0
35.0
35.0
SOT-23-THIN
SOT-23-THIN
ADC121C021QIMKX/
NOPB
ADC121C027CIMK/NOPB
SOT-23-THIN
SOT-23-THIN
DDC
DDC
6
6
1000
3000
210.0
210.0
185.0
185.0
35.0
35.0
ADC121C027CIMKX/
NOPB
Pack Materials-Page 2
PACKAGE OUTLINE
DDC0006A
SOT-23 - 1.1 max height
S
C
A
L
E
4
.
0
0
0
SMALL OUTLINE TRANSISTOR
3.05
2.55
1.1
0.7
1.75
1.45
0.1 C
B
A
PIN 1
INDEX AREA
1
6
4X 0.95
1.9
3.05
2.75
4
3
0.5
0.3
0.1
6X
TYP
0.0
0.2
C A B
C
0 -8 TYP
0.25
GAGE PLANE
SEATING PLANE
0.20
0.12
TYP
0.6
0.3
TYP
4214841/C 04/2022
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. Reference JEDEC MO-193.
www.ti.com
EXAMPLE BOARD LAYOUT
DDC0006A
SOT-23 - 1.1 max height
SMALL OUTLINE TRANSISTOR
SYMM
6X (1.1)
1
6
6X (0.6)
SYMM
4X (0.95)
4
3
(R0.05) TYP
(2.7)
LAND PATTERN EXAMPLE
EXPLOSED METAL SHOWN
SCALE:15X
METAL UNDER
SOLDER MASK
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL
EXPOSED METAL
EXPOSED METAL
0.07 MIN
ARROUND
0.07 MAX
ARROUND
NON SOLDER MASK
DEFINED
SOLDER MASK
DEFINED
SOLDERMASK DETAILS
4214841/C 04/2022
NOTES: (continued)
4. Publication IPC-7351 may have alternate designs.
5. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
DDC0006A
SOT-23 - 1.1 max height
SMALL OUTLINE TRANSISTOR
SYMM
6X (1.1)
1
6
6X (0.6)
SYMM
4X(0.95)
4
3
(R0.05) TYP
(2.7)
SOLDER PASTE EXAMPLE
BASED ON 0.125 THICK STENCIL
SCALE:15X
4214841/C 04/2022
NOTES: (continued)
6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
7. Board assembly site may have different recommendations for stencil design.
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2022, Texas Instruments Incorporated
相关型号：
ADC121C021CIMK/NOPB
I2C-Compatible, 12-Bit Analog-to-Digital Converter with Alert Pin 6-SOT-23-THIN -40 to 105
TI
ADC121C021CIMKX/NOPB
I2C-Compatible, 12-Bit Analog-to-Digital Converter with Alert Pin 6-SOT-23-THIN -40 to 105
TI
ADC121C021CIMM
IC 1-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO8, MSOP-8, Analog to Digital Converter
NSC
ADC121C021CIMM/NOPB
IC 1-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO8, MSOP-8, Analog to Digital Converter
NSC
ADC121C021CIMM/NOPB
I2C-Compatible, 12-Bit Analog-to-Digital Converter with Alert Pin 8-VSSOP -40 to 105
TI
ADC121C021CIMMX
IC 1-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO8, MSOP-8, Analog to Digital Converter
NSC
ADC121C021CIMMX/NOPB
I2C-Compatible, 12-Bit Analog-to-Digital Converter with Alert Pin 8-VSSOP -40 to 105
TI
©2020 ICPDF网 联系我们和版权申明