ADC78H90CIMTX/NOPB [TI]
8 通道、500 KSPS、12 位模数转换器 | PW | 16 | -40 to 85;
| 型号： | ADC78H90CIMTX/NOPB |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | 8 通道、500 KSPS、12 位模数转换器 | PW | 16 | -40 to 85 光电二极管 转换器 模数转换器 |
| 文件： | 总26页 (文件大小：728K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
ADC78H90
www.ti.com
SNAS227D –NOVEMBER 2003–REVISED MARCH 2013
ADC78H90 8-Channel, 500 kSPS, 12-Bit A/D Converter
Check for Samples: ADC78H90
The ADC78H90 is packaged in a 16-lead TSSOP
package. Operation over the industrial temperature
range of −40°C to +85°C is ensured.
1
FEATURES
2
•
•
•
•
•
Eight input channels
Variable power management
Connection Diagram
Independent analog and digital supplies
SPI™/QSPI™/MICROWIRE™/DSP compatible
Packaged in 16-lead TSSOP
CS
AV
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
SCLK
DOUT
DIN
DD
APPLICATIONS
AGND
AIN1
AIN2
AIN3
AIN4
AIN5
•
•
•
•
•
Automotive Navigation
Portable Systems
DV
DD
ADC78H90
DGND
AIN8
AIN7
AIN6
Medical Instruments
Mobile Communications
Instrumentation and Control Systems
KEY SPECIFICATIONS
Figure 1. 16-Lead TSSOP
See PW Package
•
•
•
•
Conversion Rate: 500kSPS
DNL: ± 1LSB (max)
INL: ± 1LSB (max)
Block Diagram
Power Consumption
AIN1
–
–
3V Supply: 1.5 mW (typ)
5V Supply: 8.3 mW (typ)
12-BIT
SUCCESSIVE
APPROXIMATION
ADC
.
.
.
AV
DD
MUX
T/H
AGND
DESCRIPTION
AGND
The ADC78H90 is a low-power, eight-channel CMOS
12-bit analog-to-digital converter with a conversion
throughput of 500 kSPS. The converter is based on a
successive-approximation register architecture with
an internal track-and-hold circuit. It can be configured
to accept up to eight input signals at inputs AIN1
through AIN8.
AIN8
DV
DD
SCLK
CS
ADC78H90
CONTROL
LOGIC
DIN
DOUT
The output serial data is straight binary, and is
compatible with several standards, such as SPI™,
QSPI™, MICROWIRE™, and many common DSP
serial interfaces.
DGND
PIN DESCRIPTIONS AND EQUIVALENT CIRCUITS
Pin
No.
Equivalent
Circuit
Description
Symbol
The ADC78H90 may be operated with independent
analog and digital supplies. The analog supply (AVDD
)
ANALOG I/O
can range from +2.7V to +5.25V, and the digital
supply (DVDD) can range from +2.7V to AVDD. Normal
power consumption using a +3V or +5V supply is 1.5
mW and 8.3 mW, respectively. The power-down
feature reduces the power consumption to just 0.3
µW using a +3V supply, or 0.5 µW using a +5V
supply.
4 - AIN1 to
Analog inputs. These signals
11
AIN8
can range from 0V to AVDD
.
DIGITAL I/O
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
2
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2003–2013, Texas Instruments Incorporated
ADC78H90
SNAS227D –NOVEMBER 2003–REVISED MARCH 2013
www.ti.com
PIN DESCRIPTIONS AND EQUIVALENT
CIRCUITS (continued)
PIN DESCRIPTIONS AND EQUIVALENT
CIRCUITS (continued)
Pin
No.
Equivalent
Circuit
Description
Pin
No.
Equivalent
Circuit
Description
Symbol
Symbol
Digital clock input. The range of
frequencies for this input is 50
kHz to 8 MHz, with ensured
performance at 8 MHz. This
clock directly controls the
conversion and readout
processes.
Positive analog supply pin. This
pin should be connected to a
quiet +2.7V to +5.25V source
and bypassed to GND with a 1
µF tantalum capacitor and a 0.1
µF ceramic monolithic capacitor
located within 1 cm of the
power pin.
16
SCLK
2
AVDD
Digital data output. The output
samples are clocked out of this
pin on falling edges of the
SCLK pin.
Positive digital supply pin. This
pin should be connected to a
+2.7V to AVDD supply, and
bypassed to GND with a 0.1 µF
ceramic monolithic capacitor
located within 1 cm of the
power pin.
15
14
1
DOUT
DIN
13
DVDD
Digital data input. The
ADC78H90's Control Register
is loaded through this pin on
rising edges of the SCLK pin.
The ground return for the
analog supply and signals.
Chip select. On the falling edge
of CS, a conversion process
begins. Conversions continue
as long as CS is held low.
3
AGND
DGND
CS
The ground return for the digital
supply and signals.
12
POWER SUPPLY
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
(1)(2)
Absolute Maximum Ratings
Analog Supply Voltage AVDD
Digital Supply Voltage DVDD
Voltage on Any Pin to GND
−0.3V to 6.5V
−0.3V to AVDD + 0.3V, max 6.5V
−0.3V to AVDD +0.3V
±10 mA
(3)
Input Current at Any Pin
Package Input Current(3)
±20 mA
(4)
Power Dissipation at TA = 25°C
See
(5)
ESD Susceptibility
Human Body Model
Machine Model
2500V
250V
Soldering Temperature, Infrared,
(6)
10 seconds
260°C
+150°C
Junction Temperature
Storage Temperature
−65°C to +150°C
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. For ensured specifications and test conditions, see the
Electrical Characteristics. The ensured specifications apply only for the test conditions listed. Some performance characteristics may
degrade when the device is not operated under the listed test conditions.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
(3) When the input voltage at any pin exceeds the power supplies (that is, VIN < AGND or VIN >VA or VD), the current at that pin should be
limited to 10 mA. The 20 mA maximum package input current rating limits the number of pins that can safely exceed the power supplies
with an input current of 10 mA to two.
(4) The absolute maximum junction temperature (TJmax) for this device is 150°C. The maximum allowable power dissipation is dictated by
TJmax, the junction-to-ambient thermal resistance (θJA), and the ambient temperature (TA), and can be calculated using the formula
PDMAX = (TJmax − TA)/θJA. In the 16-pinTSSOP, θJA is 96°C/W, so PDMAX = 1,200mW at 25°C and 625 mW at the maximum
operating ambient temperature of85°C. Note that the power consumption of this device under normal operation is a maximum of 12 mW.
The values for maximum power dissipation listed above will be reached only when the ADC78H90 is operated in a severe fault condition
(e.g. when input or output pins are driven beyond the power supply voltages, or the power supply polarity is reversed). Obviously, such
conditions should always be avoided.
(5) Human body model is 100 pF capacitor discharged through a 1.5 kΩ resistor. Machine model is 220 pF discharged through ZERO ohms
(6) See AN450, “Surface Mounting Methods and Their Effect on Product Reliability”, or the section entitled “Surface Mount” found in any
post 1986 Texas Instruments Linear Data Book, for other methods of soldering surface mount devices.
2
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: ADC78H90
ADC78H90
www.ti.com
SNAS227D –NOVEMBER 2003–REVISED MARCH 2013
(1)(2)
Operating Ratings
Operating Temperature Range
−40°C ≤ TA ≤ +85°C
+2.7V to +5.25V
+2.7V to AVDD
-0.3V to AVDD
AVDD Supply Voltage
DVDD Supply Voltage
Digital Input Pins Voltage Range
Clock Frequency
50 kHz to 8 MHz
0V to AVDD
Analog Input Voltage
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. For ensured specifications and test conditions, see the
Electrical Characteristics. The ensured specifications apply only for the test conditions listed. Some performance characteristics may
degrade when the device is not operated under the listed test conditions.
(2) All voltages are measured with respect to GND = 0V, unless otherwise specified.
Package Thermal Resistance
Package
θJA
16-lead TSSOP on 4-layer, 2 oz. PCB
96°C / W
Copyright © 2003–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: ADC78H90
ADC78H90
SNAS227D –NOVEMBER 2003–REVISED MARCH 2013
www.ti.com
(1)
ADC78H90 Converter Electrical Characteristics
The following specifications apply for AVDD = DVDD = +2.7V to 5.25V, AGND = DGND = 0V, fSCLK = 8 MHz, fSAMPLE = 500
KSPS, unless otherwise noted. Boldface limits apply for TA = TMIN to TMAX: all other limits TA = 25°C.
Limits
Symbol
Parameter
Conditions
Typical
Units
(2)
STATIC CONVERTER CHARACTERISTICS
Resolution with No Missing Codes
12
±1
±1
±2
±2
±3
±3
Bits
INL
Integral Non-Linearity
Differential Non-Linearity
Offset Error
AVDD = +5.0V, DVDD = +3.0V
AVDD = +5.0V, DVDD = +3.0V
AVDD = +5.0V, DVDD = +3.0V
AVDD = +5.0V, DVDD = +3.0V
AVDD = +5.0V, DVDD = +3.0V
AVDD = +5.0V, DVDD = +3.0V
LSB (max)
LSB (max)
LSB (max)
LSB (max)
LSB (max)
LSB (max)
DNL
VOFF
OEM
GE
Offset Error Match
Gain Error
GEM
Gain Error Match
DYNAMIC CONVERTER CHARACTERISTICS
AVDD = +5.0V, DVDD = +3.0V,
fIN = 40.2 kHz, −0.02 dBFS
SINAD
SNR
Signal-to-Noise Plus Distortion Ratio
Signal-to-Noise Ratio
73
73
70
dB (min)
dB (min)
dB (max)
AVDD = +5.0V, DVDD = +3.0V,
fIN = 40.2 kHz, −0.02 dBFS
70.8
−74
AVDD = +5.0V, DVDD = +3.0V,
fIN = 40.2 kHz, −0.02 dBFS
THD
Total Harmonic Distortion
−86
AVDD = +5.0V, DVDD = +3.0V,
fIN = 40.2 kHz, −0.02 dBFS
SFDR
ENOB
Spurious-Free Dynamic Range
Effective Number of Bits
88
11.8
-82
75.6
11.3
dB (min)
Bits (min)
dB
AVDD = +5.0V, DVDD = +3.0V,
AVDD = +5.0V, DVDD = +3.0V,
fIN = 40.2 kHz
Channel-to-Channel Crosstalk
Intermodulation Distortion, Second
Order Terms
AVDD = +5.0V, DVDD = +3.0V,
fa = 40.161 kHz, fb = 41.015 kHz
-93
-90
dB
dB
IMD
Intermodulation Distortion, Third Order
Terms
AVDD = +5.0V, DVDD = +3.0V,
fa = 40.161 kHz, fb = 41.015 kHz
AVDD = +5V
AVDD = +3V
11
8
MHz
MHz
FPBW
-3 dB Full Power Bandwidth
ANALOG INPUT CHARACTERISTICS
VIN
Input Range
0 to AVDD
V
µA (max)
pF
IDCL
DC Leakage Current
±1
Track Mode
Hold Mode
33
3
CINA
Input Capacitance
pF
DIGITAL INPUT CHARACTERISTICS
DVDD = +4.75Vto +5.25V
DVDD = +2.7V to +3.6V
DVDD = +2.7V to +5.25V
VIN = 0V or DVDD
2.4
2.1
0.8
±1
4
V (min)
V (min)
VIH
Input High Voltage
VIL
Input Low Voltage
Input Current
V (max)
µA (max)
pF (max)
IIN
±0.01
2
CIND
Digital Input Capacitance
DIGITAL OUTPUT CHARACTERISTICS
ISOURCE = 200 µA, DVDD = +2.7V to
+5.25V
VOH
VOL
Output High Voltage
Output Low Voltage
DVDD −0.5
V (min)
ISINK = 200 µA
0.4
±1
4
V (max)
µA (max)
pF (max)
IOZH, IOZL TRI-STATE® Leakage Current
COUT
TRI-STATE® Output Capacitance
Output Coding
2
Straight (Natural) Binary
(1) Data sheet min/max specification limits are ensured by design, test, or statistical analysis.
(2) Tested limits are specified to TI's AOQL (Average Outgoing Quality Level).
4
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: ADC78H90
ADC78H90
www.ti.com
SNAS227D –NOVEMBER 2003–REVISED MARCH 2013
ADC78H90 Converter Electrical Characteristics (1) (continued)
The following specifications apply for AVDD = DVDD = +2.7V to 5.25V, AGND = DGND = 0V, fSCLK = 8 MHz, fSAMPLE = 500
KSPS, unless otherwise noted. Boldface limits apply for TA = TMIN to TMAX: all other limits TA = 25°C.
Limits
Symbol
Parameter
Conditions
Typical
Units
(2)
POWER SUPPLY CHARACTERISTICS (CL = 10 pF)
2.7
V (min)
V (max)
AVDD
DVDD
,
Analog and Digital Supply Voltages
AVDD ≥ DVDD
5.25
AVDD = DVDD = +4.75V to +5.25V,
fSAMPLE = 500 kSPS, fIN = 40 kHz
1.65
0.5
2.3
2.3
mA (max)
mA (max)
nA
Total Supply Current, Normal Mode
(Operational, CS low)
AVDD = DVDD = +2.7V to +3.6V,
fSAMPLE = 500 kSPS, fIN = 40 kHz
IA + ID
AVDD = DVDD = +4.75V to +5.25V,
fSAMPLE = 0 kSPS
200
200
Total Supply Current, Shutdown (CS
high)
AVDD = DVDD = +2.7V to +3.6V,
fSAMPLE = 0 kSPS
nA
\AVDD = DVDD = +4.75V to +5.25V
AVDD = DVDD = +2.7V to +3.6V
AVDD = DVDD = +4.75V to +5.25V
AVDD = DVDD = +2.7V to +3.6V
8.3
1.5
0.5
0.3
12
mW (max)
mW (max)
µW
Power Consumption, Normal Mode
(Operational, CS low)
8.3
PD
Power Consumption, Shutdown (CS
high)
µW
AC ELECTRICAL CHARACTERISTICS
fSCLK
fSMIN
fS
Maximum Clock Frequency
Minimum Clock Frequency
Maximum Sample Rate
Conversion Time
8
MHz (min)
kHz
50
50
500
13
40
60
3
KSPS (min)
SCLK cycles
% (min)
tCONV
DC
SCLK Duty Cycle
% (max)
tACQ
Track/Hold Acquisition Time
Throughput Time
Full-Scale Step Input
SCLK cycles
SCLK cycles
kSPS (min)
ns
Acquisition Time + Conversion Time
16
500
fRATE
tAD
Throughput Rate
Aperture Delay
4
ADC78H90 Timing Specifications
The following specifications apply for AVDD = DVDD = +2.7V to 5.25V, AGND = DGND = 0V, fSCLK = 8 MHz, fSAMPLE = 500
KSPS, CL = 50 pF, Boldface limits apply for TA = TMIN to TMAX: all other limits TA = 25°C.
Limits
Symbol
Parameter
Conditions
Typical
Units
(1)
Setup Time SCLK High to CS Falling
Edge
(2)
(2)
t1a
10
ns (min)
Hold time SCLK Low to CS Falling
Edge
t1b
t2
10
30
30
ns (min)
ns (max)
ns (max)
Delay from CS Until DOUT active
Data Access Time after SCLK Falling
Edge
t3
Data Setup Time Prior to SCLK Rising
Edge
t4
10
ns (min)
t5
t6
t7
Data Valid SCLK Hold Time
SCLK High Pulse Width
SCLK Low Pulse Width
10
ns (min)
ns (min)
ns (min)
0.4 x tSCLK
0.4 x tSCLK
CS Rising Edge to DOUT High-
Impedance
t8
20
ns (max)
(1) Tested limits are specified to TI's AOQL (Average Outgoing Quality Level).
(2) Clock may be in any state (high or low) when CS is asserted, with the restrictions on setup and hold time given by t1a and t1b
.
Copyright © 2003–2013, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: ADC78H90
ADC78H90
SNAS227D –NOVEMBER 2003–REVISED MARCH 2013
www.ti.com
Timing Diagrams
Figure 2. Timing Test Circuit
Figure 3. ADC78H90 Operational Timing Diagram
CS
tCONVERT
tACQ
t6
SCLK
1
2
3
4
5
6
7
8
16
t7
t8
t2
t3
DB11 DB10
DB1 DB0
DOUT
DIN
Z3
Z2
Z1
Z0
DB9
DB8
t5
t4
DONTC
DONT DONTC ADD2 ADD1 ADD0
DONTC DONTC
Figure 4. ADC78H90 Serial Timing Diagram
6
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: ADC78H90
ADC78H90
www.ti.com
SNAS227D –NOVEMBER 2003–REVISED MARCH 2013
Figure 5. SCLK and CS Timing Parameters
Specification Definitions
ACQUISITION TIME is the time required to acquire the input voltage. That is, it is time required for the hold
capacitor to charge up to the input voltage.
APERTURE DELAY is the time between the fourth falling SCLK edge of a conversion and the time when the
input signal is acquired or held for conversion.
CONVERSION TIME is the time required, after the input voltage is acquired, for the ADC to convert the input
voltage to a digital word.
CROSSTALK is the coupling of energy from one channel into the other channel, or the amount of signal energy
from one analog input that appears at the measured analog input.
DIFFERENTIAL NON-LINEARITY (DNL) is the measure of the maximum deviation from the ideal step size of 1
LSB.
DUTY CYCLE is the ratio of the time that a repetitive digital waveform is high to the total time of one period. The
specification here refers to the SCLK.
EFFECTIVE NUMBER OF BITS (ENOB, or EFFECTIVE BITS) is another method of specifying Signal-to-Noise
and Distortion or SINAD. ENOB is defined as (SINAD - 1.76) / 6.02 and says that the converter is
equivalent to a perfect ADC of this (ENOB) number of bits
FULL POWER BANDWIDTH is a measure of the frequency at which the reconstructed output fundamental
drops 3 dB below its low frequency value for a full scale input.
GAIN ERROR is the deviation of the last code transition (111...110) to (111...111) from the ideal (VREF - 1.5
LSB), after adjusting for offset error.
INTEGRAL NON-LINEARITY (INL) is a measure of the deviation of each individual code from a line drawn from
negative full scale (½ LSB below the first code transition) through positive full scale (½ LSB above the last
code transition). The deviation of any given code from this straight line is measured from the center of that
code value.
INTERMODULATION DISTORTION (IMD) is the creation of additional spectral components as a result of two
sinusoidal frequencies being applied to the ADC input at the same time. It is defined as the ratio of the
power in the second and third order intermodulation products to the sum of the power in both of the
original frequencies. IMD is usually expressed in dB.
MISSING CODES are those output codes that will never appear at the ADC outputs. The ADC78H90 is ensured
not to have any missing codes.
OFFSET ERROR is the deviation of the first code transition (000...000) to (000...001) from the ideal (i.e. GND +
0.5 LSB).
SIGNAL TO NOISE RATIO (SNR) is the ratio, expressed in dB, of the rms value of the input signal to the rms
value of the sum of all other spectral components below one-half the sampling frequency, not including
harmonics or d.c.
SIGNAL TO NOISE PLUS DISTORTION (S/N+D or SINAD) Is the ratio, expressed in dB, of the rms value of
the input signal to the rms value of all of the other spectral components below half the clock frequency,
Copyright © 2003–2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: ADC78H90
ADC78H90
SNAS227D –NOVEMBER 2003–REVISED MARCH 2013
www.ti.com
including harmonics but excluding d.c.
SPURIOUS FREE DYNAMIC RANGE (SFDR) is the difference, expressed in dB, between the rms values of the
input signal and the peak spurious signal where a spurious signal is any signal present in the output
spectrum that is not present at the input, excluding d.c.
TOTAL HARMONIC DISTORTION (THD) is the ratio, expressed in dB or dBc, of the rms total of the first five
harmonic components at the output to the rms level of the input signal frequency as seen at the output.
THD is calculated as
2
2
A
+3+ A
f2
f6
THD = 20 log
•
10
2
A
f1
where
•
•
Af1 is the RMS power of the input frequency at the output
Af2 through Af6 are the RMS power in the first 5 harmonic frequencies
(1)
THROUGHPUT TIME is the minimum time required between the start of two successive conversion. It is the
acquisition time plus the conversion time. In the case of the ADC78H90, this is 16 SCLK periods.
8
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: ADC78H90
ADC78H90
www.ti.com
SNAS227D –NOVEMBER 2003–REVISED MARCH 2013
Typical Performance Characteristics
TA = +25°C, fSAMPLE = 500 kSPS, fSCLK = 8 MHz, fIN = 40.2 kHz unless otherwise stated.
DNL
DNL
Figure 6.
INL
Figure 7.
INL
Figure 8.
Figure 9.
DNL vs. Supply
INL vs. Supply
Figure 10.
Figure 11.
Copyright © 2003–2013, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: ADC78H90
ADC78H90
SNAS227D –NOVEMBER 2003–REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics (continued)
TA = +25°C, fSAMPLE = 500 kSPS, fSCLK = 8 MHz, fIN = 40.2 kHz unless otherwise stated.
SNR vs. Supply
THD vs. Supply
Figure 12.
Figure 13.
ENOB vs. Supply
SNR vs. Input Frequency
Figure 14.
Figure 15.
THD vs. Input Frequency
ENOB vs. Input Frequency
Figure 16.
Figure 17.
10
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: ADC78H90
ADC78H90
www.ti.com
SNAS227D –NOVEMBER 2003–REVISED MARCH 2013
Typical Performance Characteristics (continued)
TA = +25°C, fSAMPLE = 500 kSPS, fSCLK = 8 MHz, fIN = 40.2 kHz unless otherwise stated.
Spectral Response
Spectral Response
Figure 18.
Figure 19.
Power Consumption vs. Throughput
Figure 20.
Copyright © 2003–2013, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: ADC78H90
ADC78H90
SNAS227D –NOVEMBER 2003–REVISED MARCH 2013
www.ti.com
APPLICATIONS INFORMATION
ADC78H90 OPERATION
The ADC78H90 is a successive-approximation analog-to-digital converter designed around a charge-
redistribution digital-to-analog converter. Simplified schematics of the ADC78H90 in both track and hold
operation are shown in Figure 21 and Figure 22, respectively. In Figure 21, the ADC78H90 is in track mode:
switch SW1 connects the sampling capacitor to one of eight analog input channels through the multiplexer, and
SW2 balances the comparator inputs. The ADC78H90 is in this state for the first three SCLK cycles after CS is
brought low.
There is no power-up delay or dummy conversions with the ADC78H90. The ADC is able to sample and convert
an input to full resolution in the first conversion immediately following power up. The first conversion result after
power up will be that of the first channel.
Figure 22 shows the ADC78H90 in hold mode: switch SW1 connects the sampling capacitor to ground,
maintaining the sampled voltage, and switch SW2 unbalances the comparator. The control logic then instructs
the charge-redistribution DAC to add or subtract fixed amounts of charge to or from the sampling capacitor until
the comparator is balanced. When the comparator is balanced, the digital word supplied to the DAC is the digital
representation of the analog input voltage. The ADC78H90 is in this state for the last thirteen SCLK cycles after
CS is brought low.
AIN1
CHARGE
REDISTRIBUTION
DAC
MUX
SAMPLING
CAPACITOR
SW1
+
-
AIN8
CONTROL
LOGIC
SW2
AGND
AV /2
DD
Figure 21. ADC78H90 in Track Mode
AIN1
AIN8
CHARGE
REDISTRIBUTION
DAC
MUX
SAMPLING
CAPACITOR
+
-
SW1
CONTROL
LOGIC
SW2
AGND
AV /2
DD
Figure 22. ADC78H90 in Hold Mode
The time when CS is low is considered a serial frame. Each of these frames should contain an integer multiple of
16 SCLK cycles, during which time a conversion is performed and clocked out at the DOUT pin and data is
clocked into the DIN pin to indicate the multiplexer address for the next conversion.
12
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: ADC78H90
ADC78H90
www.ti.com
SNAS227D –NOVEMBER 2003–REVISED MARCH 2013
USING THE ADC78H90
Figure 3 and Figure 4 for the ADC78H90 are shown in Timing Diagrams. CS, chip select, initiates conversions
and frames the serial data transfers. SCLK (serial clock) controls both the conversion process and the timing of
serial data. DOUT is the serial data output pin, where a conversion result is sent as a serial data stream, MSB
first. Data to be written to the ADC78H90's Control Register is placed on DIN, the serial data input pin. New data
is written to DIN with each conversion.
A serial frame is initiated on the falling edge of CS and ends on the rising edge of CS. Each frame must contain
an integer multiple of 16 rising SCLK edges. The ADC output data (DOUT) is in a high impedance state when
CS is high and is active when CS is low. Thus, CS acts as an output enable. Additionally, the device goes into a
power down state when CS is high.
During the first 3 cycles of SCLK, the ADC is in the track mode, acquiring the input voltage. For the next 13
SCLK cycles the conversion is accomplished and the data is clocked out, MSB first. If there is more than one
conversion in a frame, the ADC will re-enter the track mode on the falling edge of SCLK after the N*16th rising
edge of SCLK, and re-enter the hold/convert mode on the N*16+4th falling edge of SCLK, where "N" must be an
integer.
When CS is brought high, SCLK is internally gated off. If SCLK is in a low state when CS goes high, the
subsequent fall of CS will generate a falling edge of the internal version of SCLK, putting the ADC into the track
mode. This is seen by the ADC as the first falling edge of SCLK. If SCLK is in a high state when CS goes high,
the ADC enters the track mode on the first falling edge of SCLK after the falling edge of CS.
During each conversion, data is clocked into the DIN pin on the first 8 rising edges of SCLK after the fall of CS.
For each conversion, it is necessary to clock in the data indicating the input that is selected for the conversion
after the current one. See Table 1, Table 2, and Table 3.
If CS and SCLK go low simultaneously, it is the following rising edge of SCLK that is considered the first rising
edge for clocking data into DIN.
Table 1. Control Register Bits
Bit 7 (MSB)
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
DONTC
DONTC
ADD2
ADD1
ADD0
DONTC
DONTC
DONTC
Table 2. Control Register Bit Descriptions
Bit #:
Symbol:
DONTC
ADD2
Description
7, 6, 2, 1, 0
Don't care. The value of these bit do not affect the device.
5
4
3
These three bits determine which input channel will be sampled and converted on the next falling
edge of CS. The mapping between codes and channels is shown in Table 3.
ADD1
ADD0
Table 3. Input Channel Selection
ADD2
ADD1
ADD0
Input Channel
AIN1 (Default)
AIN2
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
AIN3
AIN4
AIN5
AIN6
AIN7
AIN8
Copyright © 2003–2013, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: ADC78H90
ADC78H90
SNAS227D –NOVEMBER 2003–REVISED MARCH 2013
www.ti.com
ADC78H90 TRANSFER FUNCTION
The output format of the ADC89H90 is straight binary. Code transitions occur midway between successive
integer LSB values. The LSB width for the ADC78H90 is AVDD / 4096. The ideal transfer characteristic is shown
in Figure 23. The transition from an output code of 0000 0000 0000 to a code of 0000 0000 0001 is at 1/2 LSB,
or a voltage of AVDD / 8192. Other code transitions occur at steps of one LSB.
Figure 23. Ideal Transfer Characteristic
TYPICAL APPLICATION CIRCUIT
A typical application of the ADC78H90 is shown in Figure 24. The split analog and digital supplies are both
provided in this example by the TI LP2950 low-dropout voltage regulator, available in a variety of fixed and
adjustable output voltages. The analog supply is bypassed with a capacitor network located close to the
ADC78H90. The digital supply is separated from the analog supply by an isolation resistor and conditioned with
additional bypass capacitors. The ADC78H90 uses the analog supply (AVDD) as its reference voltage, so it is
very important that AVDD be kept as clean as possible. Because of the ADC78H90's low power requirements, it is
also possible to use a precision reference as a power supply to maximize performance. The four-wire interface is
also shown connected to a microprocessor or DSP.
100W
LP2950
5V
1 mF
TANT
0.1 mF
680 nF
0.1 mF
1 mF
0.1 mF
DV
AV
DD
DD
SCLK
CS
AIN1
.
.
.
MICROPROCESSOR
DSP
ADC78H90
DIN
AIN8
DOUT
DGND
AGND
Figure 24. Typical Application Circuit
14
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: ADC78H90
ADC78H90
www.ti.com
SNAS227D –NOVEMBER 2003–REVISED MARCH 2013
ANALOG INPUTS
An equivalent circuit for one of the ADC78H90's input channels is shown in Figure 25. Diodes D1 and D2 provide
ESD protection for the analog inputs. At no time should an analog input go beyond (AVDD + 300 mV) or (GND -
300 mV), as these ESD diodes will begin conducting, which could result in erratic operation.
The capacitor C1 in Figure 25 has a typical value of 3 pF, and is mainly the package pin capacitance. Resistor
R1 is the on resistance of the multiplexer and track / hold switch, and is typically 500 ohms. Capacitor C2 is the
ADC78H90 sampling capacitor, and is typically 30 pF. The ADC78H90 will deliver best performance when driven
by a low-impedance source to eliminate distortion caused by the charging of the sampling capacitance. This is
especially important when using the ADC78H90 to sample AC signals. Also important when sampling dynamic
signals is a band-pass or low-pass filter to reduce harmonics and noise, improving dynamic performance.
Figure 25. Equivalent Input Circuit
DIGITAL INPUTS AND OUTPUTS
The ADC78H90's digital inputs (SCLK, CS, and DIN) are limited by and cannot exceed the analog supply voltage
AVDD. The digital input pins are not prone to latch-up; SCLK, CS, and DIN may be asserted before DVDD without
any risk.
POWER SUPPLY CONSIDERATIONS
The ADC78H90 has two supplies, although they could both have the same potential. There are two major power
supply concerns with this product. They are relative power supply levels, including power on sequencing, and the
effect of digital supply noise on the analog supply.
Power Management
The ADC78H90 is a dual-supply device. These two supplies share ESD resources, and thus care must be
exercised to ensure that the power supplies are applied in the correct sequence. To avoid turning on the ESD
diodes, the digital supply (DVDD) cannot exceed the analog supply (AVDD) by more than 300 mV. The
ADC78H90's analog power supply must, therefore, be applied before (or concurrently with) the digital power
supply.
The ADC78H90 is fully powered-up whenever CS is low, and fully powered-down whenever CS is high, with one
exception: the ADC78H90 automatically enters power-down mode between the 16th falling edge of a conversion
and the 1st falling edge of the subsequent conversion (see Figure 3).
The ADC78H90 can perform multiple conversions back to back; each conversion requires 16 SCLK cycles. The
ADC78H90 will perform conversions continuously as long as CS is held low.
The user may trade off throughput for power consumption by simply performing fewer conversions per unit time.
Figure 20 in Typical Performance Characteristics shows the typical power consumption of the ADC78H90 versus
throughput. To calculate the power consumption, simply multiply the fraction of time spent in the normal mode by
the normal mode power consumption (8.3 mW with AVDD = DVDD = +3.6V, for example), and add the fraction of
time spent in shutdown mode multiplied by the shutdown mode power dissipation (0.3 mW with AVDD = DVDD
+3.6V).
=
Copyright © 2003–2013, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: ADC78H90
ADC78H90
SNAS227D –NOVEMBER 2003–REVISED MARCH 2013
www.ti.com
Power Supply Noise Considerations
The charging of any output load capacitance requires current from the digital supply, DVDD. The current pulses
required from the supply to charge the output capacitance will cause voltage variations on the digital supply. If
these variations are large enough, they could cause degrade SNR and SINAD performance of the ADC.
Furthermore, if the analog and digital supplies are tied directly together, the noise on the digital supply will be
coupled directly into the analog supply, causing greater performance degradation than noise on the digital
supply. Furthermore, discharging the output capacitance when the digital output goes from a logic high to a logic
low will dump current into the die substrate, which is resistive. Load discharge currents will cause "ground
bounce" noise in the substrate that will degrade noise performance if that current is large enough. The larger is
the output capacitance, the more current flows through the die substrate and the greater is the noise coupled into
the analog channel, degrading noise performance.
The first solution is to decouple the analog and digital supplies from each other, or use separate supplies for
them, to keep digital noise out of the analog supply. To keep noise out of the digital supply, keep the output load
capacitance as small as practical. If the load capacitance is greater than 25 pF, use a 100 Ω series resistor at
the ADC output, located as close to the ADC output pin as practical. This will limit the charge and discharge
current of the output capacitance and improve noise performance.
16
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: ADC78H90
ADC78H90
www.ti.com
SNAS227D –NOVEMBER 2003–REVISED MARCH 2013
REVISION HISTORY
Changes from Revision C (March 2013) to Revision D
Page
•
Changed layout of National Data Sheet to TI format .......................................................................................................... 16
Copyright © 2003–2013, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links: ADC78H90
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
ADC78H90CIMT/NOPB
ADC78H90CIMTX/NOPB
ACTIVE
TSSOP
TSSOP
PW
16
16
92
RoHS & Green
SN
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-40 to 85
-40 to 85
78H90
CIMT
ACTIVE
PW
2500 RoHS & Green
SN
78H90
CIMT
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Aug-2022
TAPE AND REEL INFORMATION
REEL DIMENSIONS
TAPE DIMENSIONS
K0
P1
W
B0
Reel
Diameter
Cavity
A0
A0 Dimension designed to accommodate the component width
B0 Dimension designed to accommodate the component length
K0 Dimension designed to accommodate the component thickness
Overall width of the carrier tape
W
P1 Pitch between successive cavity centers
Reel Width (W1)
QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE
Sprocket Holes
Q1 Q2
Q3 Q4
Q1 Q2
Q3 Q4
User Direction of Feed
Pocket Quadrants
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
ADC78H90CIMTX/NOPB TSSOP
PW
16
2500
330.0
12.4
6.95
5.6
1.6
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Aug-2022
TAPE AND REEL BOX DIMENSIONS
Width (mm)
H
W
L
*All dimensions are nominal
Device
Package Type Package Drawing Pins
TSSOP PW 16
SPQ
Length (mm) Width (mm) Height (mm)
367.0 367.0 35.0
ADC78H90CIMTX/NOPB
2500
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Aug-2022
TUBE
T - Tube
height
L - Tube length
W - Tube
width
B - Alignment groove width
*All dimensions are nominal
Device
Package Name Package Type
PW TSSOP
Pins
SPQ
L (mm)
W (mm)
T (µm)
B (mm)
ADC78H90CIMT/NOPB
16
92
495
8
2514.6
4.06
Pack Materials-Page 3
PACKAGE OUTLINE
PW0016A
TSSOP - 1.2 mm max height
S
C
A
L
E
2
.
5
0
0
SMALL OUTLINE PACKAGE
SEATING
PLANE
C
6.6
6.2
TYP
A
0.1 C
PIN 1 INDEX AREA
14X 0.65
16
1
2X
5.1
4.9
4.55
NOTE 3
8
9
0.30
16X
4.5
4.3
NOTE 4
1.2 MAX
0.19
B
0.1
C A B
(0.15) TYP
SEE DETAIL A
0.25
GAGE PLANE
0.15
0.05
0.75
0.50
A
20
0 -8
DETAIL A
TYPICAL
4220204/A 02/2017
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed 0.15 mm per side.
4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.25 mm per side.
5. Reference JEDEC registration MO-153.
www.ti.com
EXAMPLE BOARD LAYOUT
PW0016A
TSSOP - 1.2 mm max height
SMALL OUTLINE PACKAGE
SYMM
16X (1.5)
(R0.05) TYP
16
1
16X (0.45)
SYMM
14X (0.65)
8
9
(5.8)
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE: 10X
METAL UNDER
SOLDER MASK
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL
EXPOSED METAL
EXPOSED METAL
0.05 MAX
ALL AROUND
0.05 MIN
ALL AROUND
NON-SOLDER MASK
DEFINED
SOLDER MASK
DEFINED
15.000
(PREFERRED)
SOLDER MASK DETAILS
4220204/A 02/2017
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
PW0016A
TSSOP - 1.2 mm max height
SMALL OUTLINE PACKAGE
16X (1.5)
SYMM
(R0.05) TYP
16
1
16X (0.45)
SYMM
14X (0.65)
8
9
(5.8)
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
SCALE: 10X
4220204/A 02/2017
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2022, Texas Instruments Incorporated
相关型号：
ADC80-10
IC 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL/PARALLEL ACCESS, CDIP32, HYBRID, SIDE BRAZED, CERAMIC, DIP-24, Analog to Digital Converter
ADI
ADC80-12
IC 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL/PARALLEL ACCESS, CDIP32, HYBRID, SIDE BRAZED, CERAMIC, DIP-24, Analog to Digital Converter
ADI
©2020 ICPDF网 联系我们和版权申明