ADS1000A0IDBVTG4 [TI]
具有 PGA、振荡器和 I2C 的 12 位、128SPS、单通道 Δ-Σ ADC | DBV | 6 | -40 to 125;
| 型号： | ADS1000A0IDBVTG4 |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | 具有 PGA、振荡器和 I2C 的 12 位、128SPS、单通道 Δ-Σ ADC | DBV | 6 | -40 to 125 光电二极管 振荡器 转换器 |
| 文件： | 总23页 (文件大小：1035K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
BD0
B
u
r
r
Ć
B
r
o
w
n
P
r
o
d
u
c
t
s
ADS1000
f
r
o
m
T
e
x
a
s
I
n
s
t
r
u
m
e
n
t
s
SBAS357A–SEPTEMBER 2006–REVISED OCTOBER 2007
LOW-POWER, 12-Bit ANALOG-TO-DIGITAL CONVERTER
with I2C™ INTERFACE
1
FEATURES
DESCRIPTION
The ADS1000 is an I2C-compatible serial interface
Analog-to-Digital (A/D) converter with differential
inputs and 12 bits of resolution in a tiny SOT23-6
package. Conversions are performed ratiometrically,
using the power supply as the reference voltage. The
ADS1000 operates from a single power supply
ranging from 2.7V to 5.5V.
23
•
Complete 12-Bit Data Acquisition System in
a Tiny SOT-23 Package
•
•
•
•
Low Current Consumption: Only 90μA
Integral Nonlinearity: 1LSB Max
Single-Cycle Conversion
Programmable Gain Amplifier
Gain = 1, 2, 4, or 8
The ADS1000 performs conversions at a rate of 128
samples per second (SPS). The onboard
programmable gain amplifier (PGA), which offers
gains of up to 8, allows smaller signals to be
measured with high resolution. In single-conversion
mode, the ADS1000 automatically powers down after
a conversion, greatly reducing current consumption
during idle periods.
•
•
•
•
128SPS Data Rate
I2C Interface with Two Available Addresses
Power Supply: 2.7V to 5.5V
Pin- and Software-Compatible with 16-Bit
ADS1100
APPLICATIONS
The ADS1000 is designed for applications where
space and power consumption are major
considerations. Typical applications include portable
instrumentation, consumer goods, and voltage
monitoring.
•
•
•
•
•
Voltage Monitors
Battery Management
Industrial Process Control
Consumer Goods
Temperature Measurement
VDD
A = 1, 2, 4, or 8
VIN+
SCL
2
I C
A/D
PGA
Converter
Interface
VIN-
SDA
Clock
Oscillator
ADS1000
GND
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
3
I2C is a trademark of NXP Semiconductors, Inc.
All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2006–2007, Texas Instruments Incorporated
ADS1000
www.ti.com
SBAS357A–SEPTEMBER 2006–REVISED OCTOBER 2007
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
PACKAGE/ORDERING INFORMATION
For the most current package and ordering information, see the Package Option Addendum located at the end of
this datasheet or see the TI website at www.ti.com.
ABSOLUTE MAXIMUM RATINGS(1)
Over operating free-air temperature range (unless otherwise noted).
ADS1000
–0.3 to +6
100
UNIT
V
VDD to GND
Input Current (Momentary)
Input Current (Continuous)
Voltage to GND, VIN+, VIN–
Voltage to GND, SDA, SCL
Maximum Junction Temperature, TJ
Operating Temperature
mA
mA
V
10
–0.3 to VDD to +0.3
–0.5 to +6
+150
V
°C
°C
°C
°C
–40 to +125
–60 to +150
+300
Storage Temperature
Lead Temperature (soldering, 10s)
(1) Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to absolute
maximum conditions for extended periods may affect device reliability.
PIN CONFIGURATIONS
VIN- VDD
VIN- VDD
SDA
4
SDA
4
6
5
6
5
BD0
BD1
1
2
3
1
2
3
VIN+
VIN+
GND SCL
GND SCL
I2C address: 1001000
I2C address: 1001001
NOTE: Marking text direction indicates pin 1. Marking text depends on I2C address; see Package Option Addendum.
2
Submit Documentation Feedback
Copyright © 2006–2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1000
ADS1000
www.ti.com
SBAS357A–SEPTEMBER 2006–REVISED OCTOBER 2007
ELECTRICAL CHARACTERISTICS
All specifications at –40°C to +85°C, VDD = 5V, GND = 0V, and all PGAs, unless otherwise noted.
ADS1000
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
ANALOG INPUT
Full-Scale Input Voltage
Analog Input Voltage
Differential Input Impedance
Common-Mode Input Impedance
SYSTEM PERFORMANCE
Resolution
(VIN+) – (VIN–
)
±VDD/PGA(1)
V
VIN+, VIN– to GND
GND – 0.2
VDD + 0.2
V
2.4/PGA
8
MΩ
MΩ
No Missing Codes
12
Bits
SPS
LSB
LSB
%
Data Rate
104
128
±0.1
1
184
1
Integral Nonlinearity (INL)
Offset Error
±2
0.1
Gain Error
0.01
DIGITAL INPUT/OUTPUT
Logic Level
VIH
0.7 VDD
GND – 0.5
GND
6
V
V
V
VIL
0.3 VDD
0.4
VOL
IOL = 3mA
Input Leakage
IIH
VIH = 5.5V
VIL = GND
10
μA
μA
IIL
– 10
2.7
POWER-SUPPLY REQUIREMENTS
Power-Supply Voltage
Supply Current
VDD
Power-Down
Active
5.5
2
V
0.05
90
μA
μA
μA
μW
μW
150
Power Dissipation
VDD = 5.0V
VDD = 3.0V
450
210
750
(1) Each input, VIN+ and VIN–, must meet the absolute input voltage specifications.
Copyright © 2006–2007, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Link(s): ADS1000
ADS1000
www.ti.com
SBAS357A–SEPTEMBER 2006–REVISED OCTOBER 2007
TYPICAL CHARACTERISTICS
At TA = 25°C and VDD = 5V, unless otherwise indicated.
SUPPLY CURRENT vs TEMPERATURE
SUPPLY CURRENT vs I2C BUS FREQUENCY
120
100
80
250
225
200
175
150
125
100
75
VDD = 5V
_
25 C
_
125 C
60
VDD = 2.7V
−
_
40 C
40
50
−
−
−
10
100
1k
10k
60
40
20
0
20
40
60
80 100 120 140
I2C Bus Frequency (kHz)
_
Temperature ( C)
Figure 1.
Figure 2.
OFFSET ERROR vs TEMPERATURE
GAIN ERROR vs TEMPERATURE
2.0
1.0
0.04
0.03
PGA = 4
PGA = 8
0.02
PGA = 1
PGA = 8 PGA = 4 PGA = 2 PGA = 1
0.01
0.0
0.00
-0.01
-0.02
-0.03
-0.04
-1.0
-2.0
PGA = 2
-60 -40 -20
0
20
40
60
80 100 120 140
-60 -40 -20
0
20
40
60
80 100 120 140
Temperature (°C)
Temperature (°C)
Figure 3.
Figure 4.
DATA RATE vs TEMPERATURE
160
144
128
112
96
VDD = 2.7V
VDD = 5V
−
−
−
40 20
60
0
20
40
60
80 100 120 140
_
Temperature ( C)
Figure 5.
4
Submit Documentation Feedback
Copyright © 2006–2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1000
ADS1000
www.ti.com
SBAS357A–SEPTEMBER 2006–REVISED OCTOBER 2007
THEORY OF OPERATION
conversion has been completed, the ADS1000 places
the result in the output register, and immediately
begins another conversion. When the ADS1000 is in
continuous conversion mode, the ST/BSY bit in the
configuration register always reads '1'.
The ADS1000 is a fully differential, 12-bit A/D
converter. The ADS1000 allows users to obtain
precise measurements with a minimum of effort, and
the device is extremely easy to design with and
configure.
In single conversion mode, the ADS1000 waits until
the ST/BSY bit in the conversion register is set to '1'.
When this happens, the ADS1000 powers up and
performs a single conversion. After the conversion
completes, the ADS1000 places the result in the
output register, resets the ST/BSY bit to '0' and
powers down. Writing a '1' to ST/BSY while a
conversion is in progress has no effect.
The ADS1000 consists of an A/D converter core with
adjustable gain, a clock generator, and an I2C
interface. Each of these blocks are described in detail
in the sections that follow.
ANALOG-TO-DIGITAL CONVERTER
The ADS1000 uses a switched-capacitor input stage.
To external circuitry, it looks roughly like a resistance.
The resistance value depends on the capacitor
values and the rate at which they are switched. The
switching clock is generated by the onboard clock
generator, so its frequency, nominally 275kHz, is
dependent on supply voltage and temperature. The
capacitor values depend on the PGA setting.
When switching from continuous conversion mode to
single conversion mode, the ADS1000 will complete
the current conversion, reset the ST/BSY bit to '0' and
power-down the device.
RESET AND POWER-UP
When the ADS1000 powers up, it automatically
performs a reset. As part of the reset, the ADS1000
sets all of the bits in the configuration register to their
respective default settings.
The common-mode and differential input impedances
are different. For
a gain setting of PGA, the
differential input impedance is typically 2.4MΩ/PGA.
The common-mode impedance is typically 8MΩ.
The ADS1000 responds to the I2C General Call
Reset command. When the ADS1000 receives a
General Call Reset, it performs an internal reset,
exactly as though it had just been powered on.
OUTPUT CODE CALCULATION
The ADS1000 outputs codes in binary two’s
complement format. The output code is confined to
the range of numbers: –2048 to 2047, and is given
by:
I2C INTERFACE
The ADS1000 communicates through an I2C
(Inter-Integrated Circuit) interface. The I2C interface is
a two-wire, open-drain interface supporting multiple
devices and masters on a single bus. Devices on the
I2C bus only drive the bus lines low, by connecting
them to ground; they never drive the bus lines high.
Instead, the bus wires are pulled high by pull-up
resistors, so the bus wires are high when no device is
driving them low. This way, two devices cannot
conflict; if two devices drive the bus simultaneously,
there is no driver contention.
V
IN)*VIN−
Output Code + 2048(PGA)ǒ Ǔ
VDD
CLOCK GENERATOR
The ADS1000 features an onboard clock generator.
The Typical Characteristics show variations in data
rate over supply voltage and temperature. It is not
possible to operate the ADS1000 with an external
clock.
Communication on the I2C bus always takes place
between two devices, one acting as the master and
the other acting as the slave. Both masters and
slaves can read and write, but slaves can only do so
under the direction of the master. Some I2C devices
can act as masters or slaves, but the ADS1000 can
only act as a slave device.
USING THE ADS1000
OPERATING MODES
The ADS1000 operates in one of two modes:
continuous conversion and single conversion.
In continuous conversion mode, the ADS1000
continuously performs conversions. Once
a
Copyright © 2006–2007, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Link(s): ADS1000
ADS1000
www.ti.com
SBAS357A–SEPTEMBER 2006–REVISED OCTOBER 2007
An I2C bus consists of two lines, SDA and SCL. SDA
carries data; SCL provides the clock. All data is
transmitted across the I2C bus in groups of eight bits.
To send a bit on the I2C bus, the SDA line is driven to
the bit level while SCL is low (a Low on SDA
indicates the bit is '0'; a High indicates the bit is '1').
Once the SDA line has settled, the SCL line is
brought high, then low. This pulse on SCL clocks the
SDA bit into the receiver shift register.
The I2C bus is bidirectional: the SDA line is used both
for transmitting and receiving data. When a master
reads from a slave, the slave drives the data line;
when a master sends to a slave, the master drives
the data line. The master always drives the clock line.
The ADS1000 never drives SCL, because it cannot
act as a master. On the ADS1000, SCL is an input
only.
Every byte transmitted on the I2C bus, whether it be
address or data, is acknowledged with an
acknowledge bit. When
a master has finished
sending a byte, eight data bits, to a slave, it stops
driving SDA and waits for the slave to acknowledge
the byte. The slave acknowledges the byte by pulling
SDA low. The master then sends a clock pulse to
clock the acknowledge bit. Similarly, when a master
has finished reading a byte, it pulls SDA low to
acknowledge to the slave that it has finished reading
the byte. It then sends a clock pulse to clock the bit.
(Remember that the master always drives the clock
line.)
A not-acknowledge is performed by simply leaving
SDA high during an acknowledge cycle. If a device is
not present on the bus, and the master attempts to
address it, it will receive a not-acknowledge because
no device is present at that address to pull the line
low.
Most of the time the bus is idle, no communication
takes place, and both lines are high. When
communication takes place, the bus is active. Only
master devices can start a communication. They do
this by causing a start condition on the bus. Normally,
the data line is only allowed to change state while the
clock line is low. If the data line changes state while
the clock line is high, it is either a start condition or its
counterpart, a stop condition. A start condition is
when the clock line is high and the data line goes
from high to low. A stop condition is when the clock
line is high and the data line goes from low to high.
When a master has finished communicating with a
slave, it may issue a stop condition. When a stop
condition is issued, the bus becomes idle again. A
master may also issue another start condition. When
a start condition is issued while the bus is active, it is
called a repeated start condition.
A timing diagram for an ADS1000 I2C transaction is
shown in Figure 6. Table 1 gives the parameters for
this diagram.
After the master issues a start condition, it sends a
byte that indicates with which slave device it wants to
communicate. This byte is called the address byte.
Each device on an I2C bus has a unique 7-bit
address to which it responds. (Slaves can also have
10-bit addresses; see the I2C specification for
details.) The master sends an address in the address
byte, together with a bit that indicates whether it
wishes to read from or write to the slave device.
6
Submit Documentation Feedback
Copyright © 2006–2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1000
ADS1000
www.ti.com
SBAS357A–SEPTEMBER 2006–REVISED OCTOBER 2007
t(LOW)
t(HDSTA)
tR
tF
SCL
SDA
t(HDSTA)
t(HIGH) t(SUSTA)
t(SUSTO)
t(SUDAT)
t(HDDAT)
t(BUF)
P
S
S
P
Figure 6. I2C Timing Diagram
Table 1. Timing Diagram Definitions
FAST MODE
HIGH-SPEED MODE
PARAMETER
SCLK Operating Frequency
MIN
MAX
MIN
MAX
UNITS
MHz
ns
f(SCLK)
0.4
3.4
Bus Free Time Between STOP and START
Condition
t(BUF)
600
600
160
160
Hold Time After Repeated START Condition.
After this period, the first clock is generated.
t(HDSTA)
ns
Repeated START Condition Setup Time
STOP Condition Setup Time
Data Hold Time
t(SUSTA)
t(SUSTO)
t(HDDAT)
t(SUDAT)
t(LOW)
t(HIGH)
tF
600
600
0
160
160
0
ns
ns
ns
ns
ns
ns
ns
ns
Data Setup Time
100
1300
600
10
SCLK Clock Low Period
SCLK Clock High Period
Clock/Data Fall Time
160
60
300
300
160
160
Clock/Data Rise Time
tR
Copyright © 2006–2007, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Link(s): ADS1000
ADS1000
www.ti.com
SBAS357A–SEPTEMBER 2006–REVISED OCTOBER 2007
ADS1000 I2C ADDRESSES
The ADS1000 I2C address is either 1001000 or
1001001, set at the factory. The address is identified
with an A0 or an A1 within the orderable name.
The two different I2C variants are also marked
differently. Devices with an I2C address of 1001000
have packages marked BD0, while devices with an
I2C address of 1001001 are marked with BD1. See
mode must be activated. To activate High-speed
mode, send a special address byte of 00001XXX
following the start condition, where the XXX bits are
unique to the Hs-capable master. This byte is called
the Hs master code. (Note that this is different from
normal address bytes; the low bit does not indicate
read/write
status.)
The
ADS1000
will
not
acknowledge this byte; the I2C specification prohibits
acknowledgment of the Hs master code. On receiving
a master code, the ADS1000 will switch on its
High-speed mode filters, and will communicate at up
to 3.4MHz. The ADS1000 switches out of Hs mode
with the next stop condition.
the Package/Ordering Information Table for
a
complete listing of the ADS1000 I2C addresses and
tape and reel size.
I2C GENERAL CALL
For more information on High-speed mode, consult
the I2C specification.
The ADS1000 responds to General Call Reset, which
is an address byte of 00h followed by a data byte of
06h. The ADS1000 acknowledges both bytes.
REGISTERS
On receiving a General Call Reset, the ADS1000
performs a full internal reset, just as though it had
been powered off and then on. If a conversion is in
process, it is interrupted; the output register is set to
zero, and the configuration register returns to its
default setting.
The ADS1000 has two registers that are accessible
via its I2C port. The output register contains the result
of the last conversion; the configuration register
allows users to change the ADS1000 operating mode
and query the status of the device.
OUTPUT REGISTER
The ADS1000 always acknowledges the General Call
address byte of 00h, but it does not acknowledge any
General Call data bytes other than 04h or 06h.
The 16-bit output register contains the result of the
last conversion in binary two’s complement format.
Since the port yields 12 bits of data, the ADS1000
outputs right-justified and sign-extended codes. This
output format makes it possible to perform averaging
using a 16-bit accumulator.
I2C DATA RATES
The I2C bus operates in one of three speed modes:
Standard, which allows a clock frequency of up to
100kHz; Fast, which allows a clock frequency of up to
400kHz; and High-speed mode (also called Hs
mode), which allows a clock frequency of up to
3.4MHz. The ADS1000 is fully compatible with all
three modes.
Following reset or power-up, the output register is
cleared to '0'; it remains zero until the first conversion
is completed. Therefore, if a user reads the ADS1000
just after reset or power-up, the output register will
read '0'.
No special action needs to be taken to use the
ADS1000 in Standard or Fast modes, but High-speed
The output register format is shown in Table 2.
Table 2. OUTPUT REGISTER
BIT
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
NAME D15(1) D14(1) D13(1) D12(1)
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
(1) D15–D12 are sign extensions of 12-bit data.
8
Submit Documentation Feedback
Copyright © 2006–2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1000
ADS1000
www.ti.com
SBAS357A–SEPTEMBER 2006–REVISED OCTOBER 2007
CONFIGURATION REGISTER
A user controls the ADS1000 operating mode and
PGA settings via the 8-bit configuration register. The
configuration register format is shown in Table 3. The
default setting is 80H.
Bits 1 - 0: PGA
Bits 1 and 0 control the ADS1000 gain setting; see
Table 4.
Table 4. PGA Bits
Table 3. CONFIGURATION REGISTER
7
6
5
4
3
2
1
0
PGA1
PGA0
GAIN
0(1)
0(1)
1(1)
ST/BSY
0
0
SC
0
0
PGA1 PGA0
0
1
2
Bit 7: ST/BSY
1
0
4
1
1
8
The meaning of the ST/BSY bit depends on whether
it is being written to or read from.
(1) Default setting.
In single conversion mode, writing a '1' to the ST/BSY
bit causes a conversion to start, and writing a '0' has
no effect. In continuous conversion mode, the
ADS1000 ignores the value written to ST/BSY.
READING FROM THE ADS1000
A user can read the output register and the contents
of the configuration register from the ADS1000. To do
this, address the ADS1000 for reading, and read
three bytes from the device. The first two bytes are
the output register contents; the third byte is the
configuration register contents.
When read in single conversion mode, ST/BSY
indicates whether the A/D converter is busy taking a
conversion. If ST/BSY is read as '1', the A/D
converter is busy, and a conversion is taking place; if
'0', no conversion is taking place, and the result of the
last conversion is available in the output register.
A user does not always have to read three bytes from
the ADS1000. If only the contents of the output
register are needed, read only two bytes.
In continuous mode, ST/BSY is always read as '1'.
Bits 6 - 5: Reserved
Bits 6 and 5 must be set to zero.
Bit 4: SC
Reading more than three bytes from the ADS1000
has no effect. All of the bytes beginning with the
fourth byte will be FFh. See Figure 7 for a timing
diagram of an ADS1000 read operation.
SC controls whether the ADS1000 is in continuous
conversion or single conversion mode. When SC is
'1', the ADS1000 is in single conversion mode; when
SC is '0', the ADS1000 is in continuous conversion
mode. The default setting is '0'.
WRITING TO THE ADS1000
A user can write new contents into the configuration
register (the contents of the output register cannot
change). To do this, address the ADS1000 for writing,
and write one byte to it. This byte is written into the
configuration register.
Bits 3 - 2: Reserved
Bits 3 and 2 must be set to zero.
Writing more than one byte to the ADS1000 has no
effect. The ADS1000 ignores any bytes sent to it after
the first one, and will only acknowledge the first byte.
See Figure 8 for a timing diagram of an ADS1000
write operation.
Copyright © 2006–2007, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Link(s): ADS1000
ADS1000
www.ti.com
SBAS357A–SEPTEMBER 2006–REVISED OCTOBER 2007
1
9
1
9
SCL
···
···
SDA
R/W
1
0
0
1
A2
A1
A0
D15 D14 D13 D12 D11 D10 D9
From
D8
Start By
Master
ACK By
ACK By
Master
ADS1000
ADS1000
2
Frame 1: I C Slave Address Byte
Frame 2: Output Register Upper Byte
1
9
1
9
SCL
···
···
(Continued)
SDA
ST/
D7
D6
D5
D4
D3
D2
D1 D0
PGA1 PGA0
0
0
SC
0
0
(Continued)
BSY
From
ACK By
Master
ACK By
Master
Stop By
Master
From
ADS1000
ADS1000
Frame 3: Output Register Lower Byte
Frame 4: Configuration Register
(Optional)
Figure 7. Timing Diagram for Reading from the ADS1000
1
9
1
9
SCL
SDA
ST/
A2
0
0
PGA1 PGA0
1
0
0
1
A1
A0 R/W
0
0
SC
Stop By
Master
BSY
Start By
Master
ACK By
ACK By
ADS1000
ADS1000
2
Frame 1: I C Slave Address Byte
Frame 2: Configuration Register
Figure 8. Timing Diagram for Writing to the ADS1000
10
Submit Documentation Feedback
Copyright © 2006–2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1000
ADS1000
www.ti.com
SBAS357A–SEPTEMBER 2006–REVISED OCTOBER 2007
APPLICATION INFORMATION
The ADS1000 interfaces directly to standard mode,
fast mode, and high-speed mode I2C controllers. Any
microcontroller I2C peripheral, including master-only
and non-multiple-master I2C peripherals, will work
with the ADS1000. The ADS1000 does not perform
clock-stretching (that is, it never pulls the clock line
low), so it is not necessary to provide for this unless
other devices are on the same I2C bus.
BASIC CONNECTIONS
For many applications, connecting the ADS1000 is
extremely simple. A basic connection diagram for the
ADS1000 is shown in Figure 9.
The fully differential voltage input of the ADS1000 is
ideal for connection to differential sources with
moderately low source impedance, such as bridge
sensors and thermistors. Although the ADS1000 can
read bipolar differential signals, it cannot accept
negative voltages on either input. It may be helpful to
think of the ADS1000 positive voltage input as
noninverting, and of the negative input as inverting.
Pull-up resistors are necessary on both the SDA and
SCL lines because I2C bus drivers are open-drain.
The size of these resistors depends on the bus
operating speed and capacitance of the bus lines.
Higher-value resistors consume less power, but
increase the transition times on the bus, limiting the
bus speed. Lower-value resistors allow higher speed
at the expense of higher power consumption. Long
bus lines have higher capacitance and require
smaller pullup resistors to compensate. The resistors
should not be too small; if they are, the bus drivers
may not be able to pull the bus lines low.
When the ADS1000 is converting, it draws current in
short spikes. The 0.1μF bypass capacitor supplies
the momentary bursts of extra current needed from
the supply.
Positive Input
(0V to 5V)
Negative Input
(0V to 5V)
2
I C Pull-Up Resistors
VDD
1kW to 10kW (typ.)
ADS1000
VDD
Microcontroller or
1
2
3
VIN+
VIN-
VDD
6
5
4
Microprocessor
2
with I C Port
GND
SCL
SDA
SCL
SDA
4.7mF (typ.)
Figure 9. Typical Connections of the ADS1000
Copyright © 2006–2007, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Link(s): ADS1000
ADS1000
www.ti.com
SBAS357A–SEPTEMBER 2006–REVISED OCTOBER 2007
CONNECTING MULTIPLE DEVICES
VDD
ADS1000
VIN+ VIN-
VDD
Connecting two ADS1000s to a single bus is almost
trivial. An example showing two ADS1000s and one
ADS1100 connected on a single bus is shown in
Figure 10. Multiple devices can be connected to a
single bus (provided that their addresses are
different).
Microcontroller or
Microprocessor
2
with I C Port
1
2
3
6
5
4
GND
SCL
SDA
SCL
SDA
Note that only one set of pull-up resistors is needed
per bus. A user might find that he or she needs to
lower the pull-up resistor values slightly to
compensate for the additional bus capacitance
presented by multiple devices and increased line
length.
NOTE: ADS1000 power
and input connections
omitted for clarity.
2
I C Pull-Up Resistors
Figure 11. Using GPIO with a Single ADS1000
VDD
1kW to 10kW (typ.)
Bit-banging I2C with GPIO pins can be done by
setting the GPIO line to zero and toggling it between
input and output modes to apply the proper bus
states. To drive the line low, the pin is set to output a
'0'; to let the line go high, the pin is set to input. When
the pin is set to input, the state of the pin can be
read; if another device is pulling the line low, this
device will read as a '0' in the port input register.
ADS1000A0
Microcontroller or
1
2
3
VIN+
VIN-
VDD
6
5
4
Microprocessor
2
with I C Port
GND
SCL
SCL
SDA
SDA
ADS1000A1
Note that no pull-up resistor is shown on the SCL
line. In this simple case, the resistor is not needed;
the microcontroller can simply leave the line on
output, and set it to '1' or '0' as appropriate. It can do
this because the ADS1000 never drives its clock line
low. This technique can also be used with multiple
devices, and has the advantage of lower current
consumption resulting from the absence of a resistive
pull-up.
1
2
3
VIN+
VIN-
VDD
6
5
4
GND
SCL
SDA
ADS1100A2
NOTE: ADS1000 power
and input connections
omitted for clarity.
1
2
3
VIN+
VIN-
VDD
6
5
4
If there are any devices on the bus that may drive
their clock lines low, the above method should not be
used; the SCL line should be high-Z or zero and a
pull-up resistor provided as usual. Note also that this
cannot be done on the SDA line in any case,
because the ADS1000 does drive the SDA line low
from time to time, as all I2C devices do.
GND
SCL
SDA
Figure 10. Connecting Multiple ADS1000s
USING GPIO PORTS FOR I2C
Some microcontrollers have selectable strong pull-up
circuits built into the GPIO ports. In some cases,
these can be switched on and used in place of an
external pull-up resistor. Weak pull-ups are also
provided on some microcontrollers, but usually these
are too weak for I2C communication. If there is any
doubt about the matter, test the circuit before
committing it to production.
Most
microcontrollers
have
programmable
input/output pins that can be set in software to act as
inputs or outputs. If an I2C controller is not available,
the ADS1000 can be connected to GPIO pins, and
the I2C bus protocol simulated, or bit-banged, in
software. An example of this for a single ADS1000 is
shown in Figure 11.
12
Submit Documentation Feedback
Copyright © 2006–2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1000
ADS1000
www.ti.com
SBAS357A–SEPTEMBER 2006–REVISED OCTOBER 2007
SINGLE-ENDED INPUTS
amplifier, which can output fully differential signals.
This device can also help recover the lost bit noted
previously for single-ended positive signals.
Level-shifting can also be performed using the
DRV134.
Although the ADS1000 has a fully differential input, it
can easily measure single-ended signals. A simple
single-ended connection scheme is shown in
Figure 12. The ADS1000 is configured for
single-ended measurement by grounding either of its
input pins, usually VIN–, and applying the input signal
to VIN+. The single-ended signal can range from
–0.2V to VDD + 0.3V. The ADS1000 loses no linearity
anywhere in its input range. Negative voltages cannot
be applied to this circuit because the ADS1000 inputs
can only accept positive voltages.
LOW-SIDE CURRENT MONITOR
Figure 13 shows a circuit for a low-side shunt-type
current monitor. The circuit reads the voltage across
a shunt resistor, which is sized as small as possible
while still giving a readable output voltage. This
voltage is amplified by an OPA335 low-drift op-amp,
and the result is read by the ADS1000.
VDD
11.5kW
0V - VDD
ADS1000
Single-Ended
5V
5V
V
1
2
3
VIN+
VIN-
VDD
6
5
4
FS = 0.63V
GND
SCL
Load
OPA335
Filter Capacitor
33pF to 100pF
(typ.)
(1)
2
I C
SDA
R3
Output
Codes
ADS1000
49.9kW
(2)
RS
0 - 2048
1kW
G = 12.5
-5V
(PGA Gain = 8)
5V FS
Figure 12. Measuring Single-Ended Inputs
NOTES: (1) Pull-down resistor to allow accurate swing to 0V.
(2) RS is sized for a 50mV drop at full-scale current.
The ADS1000 input range is bipolar differential with
respect to the reference, that is, VDD
.
The
Figure 13. Low-Side Current Measurement
single-ended circuit shown in Figure 12 covers only
half the ADS1000 input scale because it does not
produce differentially negative inputs; therefore, one
bit of resolution is lost. The DRV134 balanced line
driver can be employed to regain this bit for
single-ended signals.
It is recommended that the ADS1000 be operated at
a gain of 8. The gain of the OPA335 can then be set
lower. For a gain of 8, the op amp should be
configured to give a maximum output voltage of no
greater than 0.75V. If the shunt resistor is sized to
Negative input voltages must be level-shifted. A good
candidate for this function is the THS4130 differential
provide
a maximum voltage drop of 50mV at
full-scale current, the full-scale input to the ADS1000
is 0.63V.
Copyright © 2006–2007, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Link(s): ADS1000
ADS1000
www.ti.com
SBAS357A–SEPTEMBER 2006–REVISED OCTOBER 2007
ADDITIONAL RECOMMENDATIONS
stabilized; this momentary spike can damage the
ADS1000. Sometimes this damage is incremental
and results in slow, long-term failure—which can be
The ADS1000 is fabricated in a small-geometry
low-voltage process. The analog inputs feature
protection diodes to the supply rails. However, the
current-handling ability of these diodes is limited, and
the ADS1000 can be permanently damaged by
analog input voltages that remain more than
approximately 300mV beyond the rails for extended
periods. One way to protect against overvoltage is to
place current-limiting resistors on the input lines. The
ADS1000 analog inputs can withstand momentary
currents of as large as 10mA.
distastrous
for
permanently
installed,
low-
maintenance systems.
If using an op amp or other front-end circuitry with the
ADS1000, be sure to take the performance
characteristics of this circuitry into account; a chain is
only as strong as its weakest link.
Any data converter is only as good as its reference.
For the ADS1000, the reference is the power supply,
and the power supply must be clean enough to
achieve the desired performance. If a power-supply
filter capacitor is used, it should be placed close to
the VDD pin, with no vias placed between the
capacitor and the pin. The trace leading to the pin
should be as wide as possible, even if it must be
necked down at the device.
The previous paragraph does not apply to the I2C
ports, which can both be driven to 6V regardless of
the supply.
If the ADS1000 is driven by an op amp with high
voltage supplies, such as ±12V, protection should be
provided, even if the op amp is configured so that it
will not output out-of-range voltages. Many op amps
seek to one of the supply rails immediately when
power is applied, usually before the input has
14
Submit Documentation Feedback
Copyright © 2006–2007, Texas Instruments Incorporated
Product Folder Link(s): ADS1000
ADS1000
www.ti.com
SBAS357A–SEPTEMBER 2006–REVISED OCTOBER 2007
Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Original (September 2006) to Revision A ............................................................................................... Page
•
Changed logic level min value from (0.7GND) to (0.7VDD) .................................................................................................. 3
Copyright © 2006–2007, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Link(s): ADS1000
PACKAGE OPTION ADDENDUM
www.ti.com
14-Oct-2022
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
ADS1000A0IDBVR
ADS1000A0IDBVT
ADS1000A0IDBVTG4
ADS1000A1IDBVR
ADS1000A1IDBVT
ADS1000A1IDBVTG4
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
DBV
DBV
DBV
DBV
DBV
DBV
6
6
6
6
6
6
3000 RoHS & Green
NIPDAU
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
BD0
BD0
BD0
BD1
BD1
BD1
Samples
Samples
Samples
Samples
Samples
Samples
250
250
RoHS & Green
RoHS & Green
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
3000 RoHS & Green
250
250
RoHS & Green
RoHS & Green
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
14-Oct-2022
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF ADS1000 :
Automotive : ADS1000-Q1
•
NOTE: Qualified Version Definitions:
Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
•
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
24-Apr-2020
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
ADS1000A0IDBVR
ADS1000A0IDBVT
ADS1000A1IDBVR
ADS1000A1IDBVT
SOT-23
SOT-23
SOT-23
SOT-23
DBV
DBV
DBV
DBV
6
6
6
6
3000
250
178.0
178.0
178.0
178.0
9.0
9.0
9.0
9.0
3.23
3.23
3.23
3.23
3.17
3.17
3.17
3.17
1.37
1.37
1.37
1.37
4.0
4.0
4.0
4.0
8.0
8.0
8.0
8.0
Q3
Q3
Q3
Q3
3000
250
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
24-Apr-2020
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
ADS1000A0IDBVR
ADS1000A0IDBVT
ADS1000A1IDBVR
ADS1000A1IDBVT
SOT-23
SOT-23
SOT-23
SOT-23
DBV
DBV
DBV
DBV
6
6
6
6
3000
250
180.0
180.0
180.0
180.0
180.0
180.0
180.0
180.0
18.0
18.0
18.0
18.0
3000
250
Pack Materials-Page 2
PACKAGE OUTLINE
DBV0006A
SOT-23 - 1.45 mm max height
S
C
A
L
E
4
.
0
0
0
SMALL OUTLINE TRANSISTOR
C
3.0
2.6
0.1 C
1.75
1.45
B
1.45 MAX
A
PIN 1
INDEX AREA
1
2
6
5
2X 0.95
1.9
3.05
2.75
4
3
0.50
6X
0.25
C A B
0.15
0.00
0.2
(1.1)
TYP
0.25
GAGE PLANE
0.22
0.08
TYP
8
TYP
0
0.6
0.3
TYP
SEATING PLANE
4214840/C 06/2021
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. Body dimensions do not include mold flash or protrusion. Mold flash and protrusion shall not exceed 0.25 per side.
4. Leads 1,2,3 may be wider than leads 4,5,6 for package orientation.
5. Refernce JEDEC MO-178.
www.ti.com
EXAMPLE BOARD LAYOUT
DBV0006A
SOT-23 - 1.45 mm max height
SMALL OUTLINE TRANSISTOR
PKG
6X (1.1)
1
6X (0.6)
6
SYMM
5
2
3
2X (0.95)
4
(R0.05) TYP
(2.6)
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:15X
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
METAL
EXPOSED METAL
EXPOSED METAL
0.07 MIN
ARROUND
0.07 MAX
ARROUND
NON SOLDER MASK
DEFINED
SOLDER MASK
DEFINED
(PREFERRED)
SOLDER MASK DETAILS
4214840/C 06/2021
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
DBV0006A
SOT-23 - 1.45 mm max height
SMALL OUTLINE TRANSISTOR
PKG
6X (1.1)
1
6X (0.6)
6
SYMM
5
2
3
2X(0.95)
4
(R0.05) TYP
(2.6)
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
SCALE:15X
4214840/C 06/2021
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2022, Texas Instruments Incorporated
相关型号：
©2020 ICPDF网 联系我们和版权申明