ADS1110A3IDBVTG4 [TI]

16-Bit 240SPS 1-Ch Delta-Sigma ADC With PGA, Oscillator, Voltage Reference, and I<sup>2</sup>C 6-SOT-23;


型号：	ADS1110A3IDBVTG4
厂家：	TEXAS INSTRUMENTS
描述：	16-Bit 240SPS 1-Ch Delta-Sigma ADC With PGA, Oscillator, Voltage Reference, and I<sup>2</sup>C 6-SOT-23 光电二极管转换器
文件：	总23页 (文件大小：1152K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

ADS1110

SBAS276A − MARCH 2003 − REVISED NOVEMBER 2003

16-Bit ANALOG-TO-DIGITAL CONVERTER

with Onboard Reference

FEATURES

DESCRIPTION

The ADS1110 is a precision, continuously self−calibrating

COMPLETE DATA ACQUISITION SYSTEM IN

A TINY SOT23-6 PACKAGE

Analog-to-Digital (A/D) converter with differential inputs and

up to 16 bits of resolution in a small SOT23-6 package. The

onboard 2.048V reference provides an input range of

2.048V differentially. The ADS1110 uses an I²C-compatible

serial interface and operates from a single power supply

ranging from 2.7V to 5.5V.

ONBOARD REFERENCE:

Accuracy: 2.048V 0.05%

Drift: 5ppm/°C

ONBOARD PGA

ONBOARD OSCILLATOR

16-BITS NO MISSING CODES

INL: 0.01% of FSR max

The ADS1110 can perform conversions at rates of 15, 30, 60,

or 240 samples per second. The onboard programmable

gain amplifier (PGA), which offers gains of up to 8, allows

smaller signals to be measured with high resolution. In

single-conversion mode, the ADS1110 automatically powers

CONTINUOUS SELF-CALIBRATION

SINGLE-CYCLE CONVERSION

down after

conversion, greatly reducing current

consumption during idle periods.

PROGRAMMABLE DATA RATE: 15SPS TO

240SPS

The ADS1110 is designed for applications requiring

high-resolution measurement, where space and power

consumption are major considerations. Typical applications

include portable instrumentation, industrial process control,

and smart transmitters.

I CINTERFACE—EIGHT AVAILABLE

ADDRESSES

POWER SUPPLY: 2.7V to 5.5V

LOW CURRENT CONSUMPTION: 240µA

APPLICATIONS

PORTABLE INSTRUMENTATION

INDUSTRIAL PROCESS CONTROL

SMART TRANSMITTERS

CONSUMER GOODS

FACTORY AUTOMATION

TEMPERATURE MEASUREMENT

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments

semiconductor products and disclaimers thereto appears at the end of this data sheet.

All trademarks are the property of their respective owners.

ꢀꢁ ꢂ ꢃꢄ ꢅ ꢆꢇ ꢂꢈ ꢃ ꢉꢆꢉ ꢊꢋ ꢌꢍ ꢎ ꢏꢐ ꢑꢊꢍꢋ ꢊꢒ ꢓꢔ ꢎ ꢎ ꢕꢋꢑ ꢐꢒ ꢍꢌ ꢖꢔꢗ ꢘꢊꢓ ꢐꢑꢊ ꢍꢋ ꢙꢐ ꢑꢕꢚ ꢀꢎ ꢍꢙꢔ ꢓꢑꢒ

ꢓ ꢍꢋ ꢌꢍꢎ ꢏ ꢑꢍ ꢒ ꢖꢕ ꢓ ꢊ ꢌꢊ ꢓ ꢐ ꢑꢊ ꢍꢋꢒ ꢖ ꢕꢎ ꢑꢛꢕ ꢑꢕ ꢎ ꢏꢒ ꢍꢌ ꢆꢕꢜ ꢐꢒ ꢇꢋꢒ ꢑꢎ ꢔꢏ ꢕꢋꢑ ꢒ ꢒꢑ ꢐꢋꢙ ꢐꢎ ꢙ ꢝ ꢐꢎ ꢎ ꢐ ꢋꢑꢞꢚ

ꢀꢎ ꢍ ꢙꢔꢓ ꢑ ꢊꢍ ꢋ ꢖꢎ ꢍ ꢓ ꢕ ꢒ ꢒ ꢊꢋ ꢟ ꢙꢍ ꢕ ꢒ ꢋꢍꢑ ꢋꢕ ꢓꢕ ꢒꢒ ꢐꢎ ꢊꢘ ꢞ ꢊꢋꢓ ꢘꢔꢙ ꢕ ꢑꢕ ꢒꢑꢊ ꢋꢟ ꢍꢌ ꢐꢘ ꢘ ꢖꢐ ꢎ ꢐꢏ ꢕꢑꢕ ꢎ ꢒꢚ

www.ti.com

ADS1110

www.ti.com

SBAS276A − MARCH 2003 − REVISED NOVEMBER 2003

This integrated circuit can be damaged by ESD.

Texas Instruments recommends that all

integrated circuits be handled with appropriate

precautions. Failure to observe proper handling and

installation procedures can cause damage.

(1)

ABSOLUTE MAXIMUM RATINGS

to GND

−0.3V to +6V

100mA, Momentary

10mA, Continuous

Input Current

Voltage to GND, V

, V

−0.3V to V + 0.3V

IN+ IN−

ESD damage can range from subtle performance degradation

to complete device failure. Precision integrated circuits may

be more susceptible to damage because very small

parametric changes could cause the device not to meet its

published specifications.

Voltage to GND, SDA, SCL

−0.5V to 6V

+150°C

Maximum Junction Temperature

Operating Temperature Range

Storage Temperature Range

Lead Temperature (soldering, 10s)

−40°C to +125°C

−60°C to +150°C

+300°C

(1)

Stresses above those listed under “Absolute Maximum Ratings”

may cause permanent damage to the device. Exposure to

absolute maximum conditions for extended periods may affect

device reliability.

PACKAGE/ORDERING INFORMATION

SPECIFIED

TEMPERATURE

RANGE

I C

PACKAGE

DESIGNATOR

PACKAGE

MARKING

ORDERING

NUMBER

TRANSPORT

MEDIA, QUANTITY

PRODUCT

PACKAGE−LEAD

(1)

ADDRESS

1001 000

1001 001

1001 010

1001 011

1001 100

1001 101

1001 110

1001 111

ADS1110A0IDBVT

ADS1110A0IDBVR

ADS1110A1IDBVT

ADS1110A1IDBVR

ADS1110A2IDBVT

ADS1110A2IDBVR

ADS1110A3IDBVT

ADS1110A3IDBVR

ADS1110A4IDBVT

ADS1110A4IDBVR

ADS1110A5IDBVT

ADS1110A5IDBVR

ADS1110A6IDBVT

ADS1110A6IDBVR

ADS1110A7IDBVT

ADS1110A7IDBVR

Tape and Reel, 250

Tape and Reel, 3000

Tape and Reel, 250

Tape and Reel, 3000

Tape and Reel, 250

Tape and Reel, 3000

Tape and Reel, 250

Tape and Reel, 3000

Tape and Reel, 250

Tape and Reel, 3000

Tape and Reel, 250

Tape and Reel, 3000

Tape and Reel, 250

Tape and Reel, 3000

Tape and Reel, 250

Tape and Reel, 3000

ADS1110

SOT23-6

DBV

−40°C to +85°C

ED0

ED1

ED2

ED3

ED4

ED5

ED6

ED7

(1)

For the most current specification and package information, refer to our web site at www.ti.com.

SOT23

Top View

ADS1110

www.ti.com

SBAS276A − MARCH 2003 − REVISED NOVEMBER 2003

ELECTRICAL CHARACTERISTICS

All specifications at −40°C to +85°C, V

= 5V, and all PGAs, unless otherwise noted.

ADS1110

MIN

TYP

MAX

PARAMETER

ANALOG INPUT

CONDITIONS

UNIT

Full-Scale Input Voltage

Analog Input Voltage

) − (V

)

2.048/PGA

2.8/PGA

IN+

IN−

to GND or V

IN−

to GND

GND − 0.2

+ 0.2

Differential Input Impedance

Common-Mode Input Impedance

MΩ

PGA = 1

PGA = 2

PGA = 4

PGA = 8

3.5

1.8

0.9

MΩ

SYSTEM PERFORMANCE

Resolution and No Missing Codes

DR = 00

DR = 01

DR = 10

DR = 11

Bits

Data Rate

DR = 00

DR = 01

DR = 10

DR = 11

180

240

308

SPS

Output Noise

See Typical Characteristic Curves

(1)

(2)

Integral Nonlinearity

Offset Error

DR = 11, PGA = 1, End Point Fit

0.004

0.010

% of FSR

PGA = 1

PGA = 2

PGA = 4

PGA = 8

1.2

0.7

0.5

0.4

2.5

1.5

Offset Drift

PGA = 1

PGA = 2

PGA = 4

PGA = 8

1.2

0.6

0.3

µV/°C

Offset vs V

PGA = 1

PGA = 2

PGA = 4

PGA = 8

800

400

200

150

µV/V

(3)

Gain Error

0.05

0.02

0.40

0.10

(3)

PGA Gain Error Match

Match Between Any Two PGA Gains

(3)

Gain Error Drift

ppm/°C

ppm/V

Gain vs V

Common-Mode Rejection

At DC and PGA = 8

At DC and PGA = 1

105

100

DIGITAL INPUT/OUTPUT

Logic Level

0.7 • V

GND − 0.5

0.3 • V

= 3mA

GND

0.4

Input Leakage

= 5.5V

= GND

µA

−10

2.7

POWER-SUPPLY REQUIREMENTS

Power-Supply Voltage

5.5

Supply Current

Power Down

Active Mode

0.05

240

µA

350

Power Dissipation

= 5.0V

= 3.0V

1.2

1.75

0.675

(1)

(2)

(3)

99% of full-scale.

FSR = full-scale range = 2 × 2.048V/PGA = 4.096V/PGA.

Includes all errors from onboard PGA and reference.

ADS1110

www.ti.com

SBAS276A − MARCH 2003 − REVISED NOVEMBER 2003

TYPICAL CHARACTERISTICS

At T = 25°C and V

= 5V, unless otherwise noted.

ADS1110

www.ti.com

SBAS276A − MARCH 2003 − REVISED NOVEMBER 2003

TYPICAL CHARACTERISTICS (continued)

At T = 25°C and V

= 5V, unless otherwise noted.

ADS1110

www.ti.com

SBAS276A − MARCH 2003 − REVISED NOVEMBER 2003

TYPICAL CHARACTERISTICS (continued)

At T = 25°C and V

= 5V, unless otherwise noted.

THEORY OF OPERATION

The ADS1110 is a fully differential, 16-bit, self-calibrating,

delta-sigma A/D converter. Extremely easy to design with

and configure, the ADS1110 allows precise measure-

ments to be obtained with a minimum of effort.

mance of the onboard reference as well as the perfor-

mance of the A/D converter core. There are no separate

specifications for the onboard reference itself.

The ADS1110 consists of a delta-sigma A/D converter

core with adjustable gain, a 2.048V reference, a clock os-

cillator, and an I²C interface. Each of these blocks are de-

scribed in detail in the sections that follow.

OUTPUT CODE CALCULATION

The output code is a scalar value that is, except for clip-

ping, proportional to the voltage difference between the

two analog inputs. The output code is confined to a finite

range of numbers; this range depends on the number of

bits needed to represent the code. The number of bits

needed to represent the output code for the ADS1110 de-

pends on the data rate, as shown in Table 1.

ANALOG-TO-DIGITAL CONVERTER

The ADS1110 A/D converter core consists of a differential

switched-capacitor delta-sigma modulator followed by a

digital filter. The modulator measures the voltage differ-

ence between the positive and negative analog inputs and

compares it to a reference voltage, which, in the ADS1110,

is 2.048V. The digital filter receives a high-speed bitstream

from the modulator and outputs a code, which is a number

proportional to the input voltage.

NUMBER OF

BITS

MINIMUM

CODE

MAXIMUM

CODE

DATA RATE

15SPS

−32,768

−16,384

−8192

32,767

16,383

8191

30SPS

60SPS

240SPS

−2048

2047

Table 1. Minimum and Maximum Codes

For a minimum output code of Min Code, gain setting of

PGA, and positive and negative input voltages of V_IN+and

V_IN−, the output code is given by the expression:

VOLTAGE REFERENCE

The ADS1110 contains an onboard 2.048V voltage refer-

ence. This reference is always used as the A/D converter’s

voltage reference; an external reference cannot be con-

nected. The ADS1110’s voltage reference is internal only,

and cannot be measured directly or used by external cir-

cuitry.

(V_IN)) * (V_IN*

)

Output Code + −1 Min Code PGA

2.048V

In the previous expression, it is important to note that the

negated minimum output code is used. The ADS1110

outputs codes in binary two’s complement format, so the

absolute values of the minima and maxima are not the

same; the maximum n−bit code is 2ⁿ⁻¹− 1, while the

The onboard reference’s specifications are part of the

ADS1110’s overall gain and drift specifications. The con-

verter’s drift and gain error specifications reflect the perfor-

minimum n−bit code is −1 × 2ⁿ⁻¹

ADS1110

www.ti.com

SBAS276A − MARCH 2003 − REVISED NOVEMBER 2003

For example, the ideal expression for output codes with a

data rate of 16SPS and PGA = 2 is:

generated by the onboard clock oscillator, so its frequency,

nominally 275kHz, is dependent on supply voltage and

temperature.

(V_IN)) * (V_IN*

)

Output Code + 16384 2

The common-mode and differential input impedances are

different. For a gain setting of PGA, the differential input

impedance is typically:

2.048V

The ADS1110 outputs all codes right-justified and

sign-extended. This makes it possible to perform

averaging on the higher data rate codes using only a 16-bit

accumulator.

2.8MΩ/PGA

The common-mode impedance also depends on the PGA

setting. See the Electrical Characteristics for details.

Table 2 shows the output codes for various input levels.

The typical value of the input impedance often cannot be

neglected. Unless the input source has a low impedance,

the ADS1110’s input impedance may affect the

measurement accuracy. For sources with high output

impedance, buffering may be necessary. Bear in mind,

however, that active buffers introduce noise, and also

introduce offset and gain errors. All of these factors should

be considered in high-accuracy applications.

SELF-CALIBRATION

The previous expressions for the ADS1110’s output code

do not account for the gain and offset errors in the

modulator. To compensate for these, the ADS1110

incorporates self-calibration circuitry.

The self-calibration system operates continuously and

requires no user intervention. No adjustments can be

made to the self-calibration system, and none need to be

made. The self-calibration system cannot be deactivated.

Because the clock oscillator frequency drifts slightly with

temperature, the input impedances will also drift. For many

applications, this input impedance drift can be neglected,

and the expression given above for typical input

impedance can be used.

The offset and gain error figures shown in the Electrical

Characteristics include the effects of calibration.

ALIASING

CLOCK OSCILLATOR

If frequencies are input to the ADS1110 that exceed half

the data rate, aliasing will occur. To prevent aliasing, the

input signal must be bandlimited. Some signals are

inherently bandlimited. For example, a thermocouple’s

output, which has a limited rate of change, may

nevertheless contain noise and interference components.

These can fold back into the sampling band just as any

other signal can.

The ADS1110 features an onboard clock oscillator, which

drives the operation of the modulator and digital filter. The

Typical Characteristics show variations in data rate over

supply voltage and temperature.

It is not possible to operate the ADS1110 with an external

system clock.

The ADS1110’s digital filter provides some attenuation of

high-frequency noise, but the digital filter’s Sinc¹

frequency response cannot completely replace an

anti-aliasing filter. For a few applications, some external

filtering may be needed; in such applications, a simple RC

filter will suffice.

INPUT IMPEDANCE

The ADS1110 uses a switched-capacitor input stage. To

external circuitry, it looks roughly like a resistance. The

resistance value depends on the capacitor values and the

rate at which they are switched. The switching frequency

is the same as the modulator frequency; the capacitor

values depend on the PGA setting. The switching clock is

When designing an input filter circuit, remember to take

into account the interaction between the filter network and

the input impedance of the ADS1110.

DIFFERENTIAL INPUT SIGNAL

DATA RATE

(1)

−2.048V

−1LSB

ZERO

+1LSB

+2.048V

15SPS

30SPS

60SPS

240SPS

8000

FFFF

0000

0001

7FFF

3FFF

1FFF

07FF

C000

E000

F800

(1)

Differential input only; do not drive the ADS1110’s inputs below −200mV.

Table 2. Output Codes for Different Input Signals

ADS1110

www.ti.com

SBAS276A − MARCH 2003 − REVISED NOVEMBER 2003

An I²C bus consists of two lines, SDA and SCL. SDA

carries data; SCL provides the clock. All data is

transmitted across the I²C bus in groups of eight bits. To

send a bit on the I²C bus, the SDA line is driven to the

appropriate level while SCL is LOW (a LOW on SDA

indicates the bit is zero; a HIGH indicates the bit is one).

Once the SDA line has settled, the SCL line is brought

HIGH, then LOW. This pulse on SCL clocks the SDA bit

into the receiver’s shift register.

USING THE ADS1110

OPERATING MODES

The ADS1110 operates in one of two modes: continuous

conversion or single conversion.

In continuous conversion mode, the ADS1110 continuous-

ly performs conversions. Once a conversion has been

completed, the ADS1110 places the result in the output

The I²C bus is bidirectional: the SDA line is used both for

transmitting and receiving data. When a master reads from

a slave, the slave drives the data line; when a master

sends to a slave, the master drives the data line. The

master always drives the clock line. The ADS1110 never

drives SCL, because it cannot act as a master. On the

ADS1110, SCL is an input only.

In single conversion mode, the ADS1110 waits until the

ST/DRDY bit in the conversion register is set to 1. When

this happens, the ADS1110 powers up and performs a

single conversion. After the conversion completes, the

ADS1110 places the result in the output register, resets the

ST/DRDY bit to 0, and powers down. Writing a 1 to

ST/DRDY while a conversion is in progress has no effect.

Most of the time the bus is idle, no communication is taking

place, and both lines are HIGH. When communication is

taking place, the bus is active. Only master devices can

start a communication. They do this by causing a START

condition on the bus. Normally, the data line is only allowed

to change state while the clock line is LOW. If the data line

changes state while the clock line is HIGH, it is either a

START condition or its counterpart, a STOP condition. A

START condition is when the clock line is HIGH and the

data line goes from HIGH to LOW. A STOP condition is

when the clock line is HIGH and the data line goes from

LOW to HIGH.

When switched from continuous conversion mode to

single conversion mode, the ADS1110 completes the

current conversion, resets the ST/DRDY bit to 0, and

powers down.

RESET AND POWER−UP

When the ADS1110 powers up, it automatically performs

a reset. As part of the reset, the ADS1110 sets all of the bits

in the configuration register to their default settings.

After the master issues a START condition, it sends a byte

that indicates which slave device it wants to communicate

with. This byte is called the address byte. Each device on

an I²C bus has a unique 7-bit address to which it responds.

(Slaves can also have 10-bit addresses; see the I²C

specification for details.) The master sends an address in

the address byte, together with a bit that indicates whether

it wishes to read from or write to the slave device.

The ADS1110 responds to the I²C General Call Reset

command. When the ADS1110 receives a General Call

Reset, it performs an internal reset, exactly as though it

had just been powered on.

I C INTERFACE

The ADS1110 communicates through an I²C

(inter-integrated circuit) interface. I²C is a two-wire

open-drain interface supporting multiple devices and

masters on a single bus. Devices on the I²C bus only drive

the bus lines LOW by connecting them to ground; they

never drive the bus lines HIGH. Instead, the bus wires are

pulled HIGH by pull-up resistors, so the bus wires are

HIGH when no device is driving them LOW. This way, two

devices cannot conflict; if two devices drive the bus

simultaneously, there is no driver contention.

Every byte transmitted on the I²C bus, whether it is

address or data, is acknowledged with an acknowledge

bit. When a master has finished sending a byte (eight data

bits) to a slave, it stops driving SDA and waits for the slave

to acknowledge the byte. The slave acknowledges the

byte by pulling SDA LOW. The master then sends a clock

pulse to clock the acknowledge bit. Similarly, when a

master has finished reading a byte, it pulls SDA LOW to

acknowledge this to the slave. It then sends a clock pulse

to clock the bit. (Remember that the master always drives

the clock line.)

Communication on the I²C bus always takes place

between two devices, one acting as the master and the

other acting as the slave. Both masters and slaves can

read and write, but slaves can only do so under the

direction of the master. Some I²C devices can act as

masters or slaves, but the ADS1110 can only act as a slave

device.

A not-acknowledge is performed by simply leaving SDA

HIGH during an acknowledge cycle. If a device is not

present on the bus, and the master attempts to address it,

it will receive a not−acknowledge because no device is

present at that address to pull the line LOW.

ADS1110

www.ti.com

SBAS276A − MARCH 2003 − REVISED NOVEMBER 2003

When a master has finished communicating with a slave,

it may issue a STOP condition. When a STOP condition is

issued, the bus becomes idle again. A master may also

issue another START condition. When a START condition

is issued while the bus is active, it is called a repeated

START condition.

Each variant of the ADS1110 is marked with EDx, where

x identifies the address variant. For example, the

ADS1110A0 is marked ED0, and the ADS1110A3 is

marked ED3. See the Package/Ordering Information table

for a complete listing.

A timing diagram for an ADS1110 I²C transaction is shown

in Figure 1. The parameters for this diagram are given in

Table 3.

I C GENERAL CALL

The ADS1110 responds to a General Call Reset, which is

an address byte of 00h followed by a data byte of 06_H. The

ADS1110 acknowledges both bytes.

ADS1110 I C ADDRESSES

The ADS1110 I²C address is 1001aaa, where aaa are bits

set at the factory. The ADS1110 is available in eight

different versions, each having a different I²C address. For

example, the ADS1110A0 has address 1001000, and the

ADS1110A3 has address 1001011. See the Ordering

Information table for a complete listing.

On receiving a General Call Reset, the ADS1110 performs

a full internal reset, just as though it had been powered off

and then on. If a conversion is in process, it is interrupted;

the output register is set to zero, and the configuration

The ADS1110 always acknowledges the General Call

address byte of 00_H, but it does not acknowledge any

General Call data bytes other than 04_Hor 06_H.

The I²C address is the only difference between the eight

variants. In all other respects, they operate identically.

Figure 1. I C Timing Diagram

FAST MODE

HIGH-SPEED MODE

MIN

MAX

MIN

MAX

PARAMETER

UNITS

SCLK operating frequency

0.4

3.4

MHz

(SCLK)

Bus free time between START and STOP condition

600

160

(BUF)

Hold time after repeated START condition.

After this period, the first clock is generated.

(HDSTA)

Repeated START condition setup time

Stop condition setup time

Data hold time

600

160

(SUSTA)

(SUSTO)

(HDDAT)

Data setup time

100

1300

600

(SUDAT)

SCLK clock LOW period

SCLK clock HIGH period

Clock/data fall time

160

(LOW)

(HIGH)

300

160

Clock/data rise time

Table 3. Timing Diagram Definitions

ADS1110

www.ti.com

SBAS276A − MARCH 2003 − REVISED NOVEMBER 2003

For more information on High-speed mode, consult the I²C

specification.

I C DATA RATES

The I²C bus operates in one of three speed modes:

Standard, which allows a clock frequency of up to 100kHz;

Fast, which allows a clock frequency of up to 400kHz; and

High-speed mode (also called Hs mode), which allows a

clock frequency of up to 3.4MHz. The ADS1110 is fully

compatible with all three modes.

REGISTERS

The ADS1110 has two registers that are accessible via its

I²C port. The output register contains the result of the last

conversion; the configuration register allows the user to

change the ADS1110 operating mode and query the status

of the device.

No special action needs to be taken to use the ADS1110

in Standard or Fast modes, but High-speed mode must be

activated. To activate High-speed mode, send a special

address byte of 00001xxx following the START condition,

where xxx are bits unique to the Hs-capable master. This

byte is called the Hs master code. (Note that this is different

from normal address bytes: the low bit does not indicate

read/write status.) The ADS1110 will not acknowledge this

byte; the I²C specification prohibits acknowledgment of

the Hs master code. On receiving a master code, the

ADS1110 will switch on its Hs mode filters, and

communicate at up to 3.4MHz. The ADS1110 will switch

out of Hs mode with the next STOP condition.

OUTPUT REGISTER

The 16-bit output register contains the result of the last

conversion in binary two’s complement format. Following

reset or power−up, the output register is cleared to zero;

it remains zero until the first conversion is completed.

The output register’s format is shown in Table 4.

BIT

NAME

D15

D14

D13

D12

D11

D10

Table 4. Output Register

ADS1110

www.ti.com

SBAS276A − MARCH 2003 − REVISED NOVEMBER 2003

Note that the output register is returned from the ADS1110

before the configuration register. The state of the

ST/DRDY bit applies to the data just read from the output

CONFIGURATION REGISTER

The 8-bit configuration register can be used to control the

ADS1110’s operating mode, data rate, and PGA settings.

The configuration register format is shown in Table 5. The

default setting is 8C_H.

Bits 6−5: Reserved

Bits 6 and 5 must be set to zero.

Bit 4: SC

BIT

ST/DRDY

DR1

NAME

DR0 PGA1 PGA0

DEFAULT

SC controls whether the ADS1110 is in continuous

conversion or single conversion mode. When SC is 1, the

ADS1110 is in single conversion mode; when SC is 0, the

ADS1110 is in continuous conversion mode. The default

setting is 0.

Table 5. Configuration Register

Bit 7: ST/DRDY

The meaning of the ST/DRDY bit depends on whether it is

being written to or read from.

Bits 3−2: DR

In single conversion mode, writing a 1 to the ST/DRDY bit

causes a conversion to start, and writing a 0 has no effect.

In continuous conversion mode, the ADS1110 ignores the

value written to ST/DRDY.

Bits 3 and 2 control the ADS1110’s data rate, as shown in

Table 6.

DR1

DR0

DATA RATE

240SPS

60SPS

When read, ST/DRDY indicates whether the data in the

output register is new data. If ST/DRDY is 0, the data just

read from the output register is new, and has not been read

before. If ST/DRDY is 1, the data just read from the output

30SPS

(1)

15SPS

(1)

Default setting.

The ADS1110 sets ST/DRDY to 0 when it writes data into

the output register. It sets ST/DRDY to 1 after any of the

bits in the configuration register have been read. (Note that

the read value of the bit is independent of the value written

to this bit.)

Table 6. DR Bits

Bits 1−0: PGA

Bits 1 and 0 control the ADS1110’s gain setting, as shown

in Table 7.

In continuous-conversion mode, use ST/DRDY to

determine when new conversion data is ready. If

ST/DRDY is 1, the data in the output register has already

been read, and is not new. If it is 0, the data in the output

PGA1

PGA0

GAIN

(1)

In single-conversion mode, use ST/DRDY to determine

when a conversion has completed. If ST/DRDY is 1, the

output register data is old, and the conversion is still in

process; if it is 0, the output register data is the result of the

new conversion.

(1)

Default setting.

Table 7. PGA Bits

ADS1110

www.ti.com

SBAS276A − MARCH 2003 − REVISED NOVEMBER 2003

it will return the same data each time. New data will be

returned only when the output register has been updated.

READING FROM THE ADS1110

To read the output register and the configuration register

from the ADS1110, address the ADS1110 for reading, then

read three bytes. The first two bytes will be the output

A timing diagram of a typical ADS1110 read operation is

shown in Figure 2.

WRITING TO THE ADS1110

It is not required to read the configuration register byte. It

is permissible to read fewer than three bytes during a read

operation.

To write to the configuration register, address the ADS1110

for writing, and send one byte. The byte will be written to

the configuration register. Note that the output register

cannot be written to.

Reading more than three bytes from the ADS1110 has no

effect. All bytes following the third will be FF_H.

Writing more than one byte to the ADS1110 has no effect.

The ADS1110 will ignore any bytes sent to it after the first

one, and it will only acknowledge the first byte.

It is possible to ignore the ST/DRDY bit and read data from

the ADS1110’s output register at any time, without regard

to whether a new conversion is complete. If the output

A timing diagram of a typical ADS1110 write operation is

shown in Figure 3.

Figure 2. Timing Diagram for Reading From the ADS1110

Figure 3. Timing Diagram for Writing To the ADS1110

ADS1110

www.ti.com

SBAS276A − MARCH 2003 − REVISED NOVEMBER 2003

Pull-up resistors are necessary on both the SDA and SCL

lines because I²C bus drivers are open-drain. The size of

these resistors depends on the bus operating speed and

capacitance of the bus lines. Higher-value resistors

consume less power, but increase the transition times on

the bus, limiting the bus speed. Lower-value resistors

allow higher speed at the expense of higher power

consumption. Long bus lines have higher capacitance and

require smaller pull-up resistors to compensate. The

resistors should not be too small; if they are, the bus drivers

may not be able to pull the bus lines low.

APPLICATIONS INFORMATION

The sections that follow give example circuits and tips for

using the ADS1110 in various situations.

BASIC CONNECTIONS

For many applications, connecting the ADS1110 is

extremely simple. A basic connection diagram for the

ADS1110 is shown in Figure 4.

CONNECTING MULTIPLE DEVICES

Connecting multiple ADS1110s to a single bus is trivial.

The ADS1110 is available in eight different versions, each

of which has a different I²C address. An example showing

three ADS1110s connected on a single bus is shown in

Figure 5. Up to eight ADS1110s (provided their addresses

are different) can be connected to a single bus.

Figure 4. Typical Connections of the ADS1110

The fully differential voltage input of the ADS1110 is ideal

for connection to differential sources with moderately low

source impedance, such as bridge sensors and

thermistors. Although the ADS1110 can read bipolar

differential signals, it cannot accept negative voltages on

either input. It may be helpful to think of the ADS1110

positive voltage input as non−inverting, and of the negative

input as inverting.

When the ADS1110 is converting, it draws current in short

spikes. The 0.1µF bypass capacitor supplies the

momentary bursts of extra current needed from the supply.

The ADS1110 interfaces directly to standard mode, fast

mode, and high−speed mode I²C controllers. Any

microcontroller’s I²C peripheral, including master-only

and non-multiple-master I²C peripherals, will work with the

Figure 5. Connecting Multiple ADS1110s

ADS1110.

The

ADS1110

does

not

perform

Note that only one set of pull-up resistors is needed per

bus. The pull-up resistor values may need to be lowered

slightly to compensate for the additional bus capacitance

presented by multiple devices and increased line length.

clock-stretching (i.e., it never pulls the clock line low), so

it is not necessary to provide for this unless

clock-stretching devices are on the same I²C bus.

ADS1110

www.ti.com

SBAS276A − MARCH 2003 − REVISED NOVEMBER 2003

Figure 6 shows a circuit with several different devices

connected to a single I²C bus. A Texas Instruments

TMP100 temperature sensor and a Texas Instruments

DAC8574 4-channel 16-bit digital-to-analog converter

share the bus with two ADS1110s.

Figure 7. Using GPIO with a Single ADS1110

Bit-banging I²C with GPIO pins can be done by setting the

GPIO line to zero and toggling it between input and output

modes to apply the proper bus states. To drive the line low,

the pin is set to output a zero; to let the line go high, the pin

is set to input. When the pin is set to input, the state of the

pin can be read; if another device is pulling the line low, this

will read as a zero in the port’s input register.

Note that no pull-up resistor is shown on the SCL line. In

this simple case, the resistor is not needed; the

microcontroller can simply leave the line on output, and set

it to one or zero as appropriate. It can do this because the

ADS1110 never drives its clock line low. This technique

can also be used with multiple devices, and has the

advantage of lower current consumption due to the

absence of a resistive pull-up.

If there are any devices on the bus that may drive their

clock lines low, the above method should not be used; the

SCL line should be high-Z or zero and a pull-up resistor

provided as usual. Note also that this cannot be done on

the SDA line in any case, because the ADS1110 does drive

the SDA line low from time to time, as all I²C devices do.

Figure 6. Connecting Multiple Device Types

The TMP100 and DAC8574 devices detect their I²C bus

addresses based on the states of pins. In the example, the

TMP100 has the address 1001011, and the DAC8574 has

the address 1001100. Consult the DAC8574 and TMP100

data sheets, located at www.ti.com, for details.

Some microcontrollers have selectable strong pull-up

circuits built in to their GPIO ports. In some cases, these

can be switched on and used in place of an external pull-up

resistor. Weak pull-ups are also provided on some

microcontrollers, but usually these are too weak for I²C

communication. If there is any doubt about the matter, test

the circuit before committing it to production.

USING GPIO PORTS FOR I C

Most microcontrollers have programmable input/output

pins that can be set in software to act as inputs or outputs.

If an I²C controller is not available, the ADS1110 can be

connected to GPIO pins and the I²C bus protocol

simulated, or “bit-banged”, in software. An example of this

for a single ADS1110 is shown in Figure 7.

ADS1110

www.ti.com

SBAS276A − MARCH 2003 − REVISED NOVEMBER 2003

SINGLE-ENDED INPUTS

Although the ADS1110 has a fully differential input, it can

easily measure single-ended signals.

simple

single-ended connection scheme is shown in Figure 8.

The ADS1110 is configured for single-ended

measurement by grounding either of its input pins, usually

_IN−, and applying the input signal to V_IN+. The

single-ended signal can range from 0V to 2.048V. The

ADS1110 loses no linearity anywhere in its input range.

Negative voltages cannot be applied to this circuit

because the ADS1110 inputs can only accept positive

voltages.

Figure 9. Low-Side Current Measurement

It is suggested that the ADS1110 be operated at a gain of

8. The gain of the OPA335 can then be set lower. For a gain

of 8, the op amp should be set up to give a maximum output

voltage of no greater than 0.256V. If the shunt resistor is

sized to provide a maximum voltage drop of 50mV at

full-scale current, the full-scale input to the ADS1110 is

0.2V.

Figure 8. Measuring Single-Ended Inputs

ADVICE

The ADS1110 input range is bipolar differential with

respect to the reference, i.e. 2.048V. The single-ended

circuit shown in Figure 8 covers only half the ADS1110

input scale because it does not produce differentially

negative inputs; therefore, one bit of resolution is lost.

The ADS1110 is fabricated in

a small-geometry

low-voltage process. The analog inputs feature protection

diodes to the supply rails. However, the current-handling

ability of these diodes is limited, and the ADS1110 can be

permanently damaged by analog input voltages that

remain more than approximately 300mV beyond the rails

for extended periods. One way to protect against

overvoltage is to place current-limiting resistors on the

input lines. The ADS1110 analog inputs can withstand

momentary currents of as large as 10mA.

LOW-SIDE CURRENT MONITOR

Figure 9 shows a circuit for a low-side shunt-type current

monitor. The circuit reads the voltage across a shunt

resistor, which is sized as small as possible while still

giving a readable output voltage. This voltage is amplified

by an OPA335 low-drift op amp and the result is read by the

ADS1110.

The previous paragraph does not apply to the I²C ports,

which can both be driven to 6V regardless of the supply.

If the ADS1110 is driven by an op amp with high-voltage

supplies, such as 12V, protection should be provided,

even if the op amp is configured so that it does not output

out-of-range voltages. Many op amps seek to one of the

supply rails immediately when power is applied, usually

before the input has stabilized; this momentary spike can

damage the ADS1110. Sometimes this damage is

incremental and results in slow, long-term failure—which

can be disastrous for permanently installed,

low-maintenance systems.

If an op amp or other front-end circuitry is used with the

ADS1110, its performance characteristics must be taken

into account. A chain is only as strong as its weakest link.

PACKAGE OPTION ADDENDUM

www.ti.com

10-Jun-2014

PACKAGING INFORMATION

Orderable Device

ADS1110A0IDBVR

ADS1110A0IDBVRG4

ADS1110A0IDBVT

ADS1110A0IDBVTG4

ADS1110A1IDBVR

ADS1110A1IDBVRG4

ADS1110A1IDBVT

ADS1110A1IDBVTG4

ADS1110A2IDBVR

ADS1110A2IDBVT

ADS1110A2IDBVTG4

ADS1110A3IDBVT

ADS1110A3IDBVTG4

ADS1110A4IDBVR

ADS1110A4IDBVT

ADS1110A4IDBVTG4

ADS1110A5IDBVR

Status Package Type Package Pins Package

Eco Plan

Lead/Ball Finish

MSL Peak Temp

Op Temp (°C)

Device Marking

Samples

Drawing

Qty

(1)

(2)

(6)

(3)

(4/5)

ACTIVE

SOT-23

DBV

3000

Green (RoHS

& no Sb/Br)

CU NIPDAU

Level-1-260C-UNLIM

ED0

ED1

ED2

ED3

ED4

ED5

ACTIVE

DBV

3000

250

Green (RoHS

& no Sb/Br)

Green (RoHS

& no Sb/Br)

250

Green (RoHS

& no Sb/Br)

3000

250

Green (RoHS

& no Sb/Br)

Green (RoHS

& no Sb/Br)

Green (RoHS

& no Sb/Br)

250

Green (RoHS

& no Sb/Br)

3000

250

Green (RoHS

& no Sb/Br)

Green (RoHS

& no Sb/Br)

250

Green (RoHS

& no Sb/Br)

250

Green (RoHS

& no Sb/Br)

250

Green (RoHS

& no Sb/Br)

3000

250

Green (RoHS

& no Sb/Br)

Green (RoHS

& no Sb/Br)

250

Green (RoHS

& no Sb/Br)

3000

Green (RoHS

& no Sb/Br)

Addendum-Page 1

PACKAGE OPTION ADDENDUM

www.ti.com

10-Jun-2014

Orderable Device

Status Package Type Package Pins Package

Eco Plan

Lead/Ball Finish

MSL Peak Temp

Op Temp (°C)

Device Marking

Samples

Drawing

Qty

(1)

(2)

(6)

(3)

(4/5)

ADS1110A5IDBVRG4

ADS1110A5IDBVT

ADS1110A5IDBVTG4

ADS1110A6IDBVT

ADS1110A7IDBVR

ADS1110A7IDBVT

ACTIVE

SOT-23

DBV

3000

Green (RoHS

& no Sb/Br)

CU NIPDAU

Level-1-260C-UNLIM

ED5

ED6

ED7

ACTIVE

DBV

250

3000

250

Green (RoHS

& no Sb/Br)

Green (RoHS

& no Sb/Br)

Green (RoHS

& no Sb/Br)

Green (RoHS

& no Sb/Br)

Green (RoHS

& no Sb/Br)

⁽¹⁾The marketing status values are defined as follows:

ACTIVE: Product device recommended for new designs.

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.

NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.

PREVIEW: Device has been announced but is not in production. Samples may or may not be available.

OBSOLETE: TI has discontinued the production of the device.

⁽²⁾Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability

information and additional product content details.

TBD: The Pb-Free/Green conversion plan has not been defined.

Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that

lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.

Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between

the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.

Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight

in homogeneous material)

⁽³⁾MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

⁽⁴⁾There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

⁽⁵⁾Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation

of the previous line and the two combined represent the entire Device Marking for that device.

Addendum-Page 2

PACKAGE OPTION ADDENDUM

www.ti.com

10-Jun-2014

⁽⁶⁾Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish

value exceeds the maximum column width.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information

provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and

continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.

TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

Addendum-Page 3

PACKAGE MATERIALS INFORMATION

www.ti.com

26-Jan-2013

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device

Package Package Pins

Type Drawing

SPQ

Reel

Pin1

Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant

(mm) W1 (mm)

ADS1110A0IDBVR

ADS1110A0IDBVT

ADS1110A1IDBVR

ADS1110A1IDBVT

ADS1110A2IDBVR

ADS1110A2IDBVT

ADS1110A3IDBVT

ADS1110A4IDBVR

ADS1110A4IDBVT

ADS1110A5IDBVR

ADS1110A5IDBVT

ADS1110A6IDBVT

ADS1110A7IDBVR

ADS1110A7IDBVT

SOT-23

DBV

3000

250

178.0

9.0

3.23

3.17

1.37

4.0

8.0

3000

250

3000

250

3000

250

3000

250

3000

250

Pack Materials-Page 1

PACKAGE MATERIALS INFORMATION

www.ti.com

26-Jan-2013

*All dimensions are nominal

Device

Package Type Package Drawing Pins

SPQ

Length (mm) Width (mm) Height (mm)

ADS1110A0IDBVR

ADS1110A0IDBVT

ADS1110A1IDBVR

ADS1110A1IDBVT

ADS1110A2IDBVR

ADS1110A2IDBVT

ADS1110A3IDBVT

ADS1110A4IDBVR

ADS1110A4IDBVT

ADS1110A5IDBVR

ADS1110A5IDBVT

ADS1110A6IDBVT

ADS1110A7IDBVR

ADS1110A7IDBVT

SOT-23

DBV

3000

250

180.0

18.0

3000

250

3000

250

3000

250

3000

250

3000

250

Pack Materials-Page 2

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other

changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest

issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and

complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale

supplied at the time of order acknowledgment.

TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms

and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary

to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily

performed.

TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and

applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide

adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or

other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information

published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or

endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the

third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration

and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered

documentation. Information of third parties may be subject to additional restrictions.

Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service

voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.

TI is not responsible or liable for any such statements.

Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements

concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support

that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which

anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause

harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use

of any TI components in safety-critical applications.

In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to

help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and

requirements. Nonetheless, such components are subject to these terms.

No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties

have executed a special agreement specifically governing such use.

Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in

military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components

which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and

regulatory requirements in connection with such use.

TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of

non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.

Products

Applications

Audio

www.ti.com/audio

amplifier.ti.com

dataconverter.ti.com

www.dlp.com

Automotive and Transportation www.ti.com/automotive

Communications and Telecom www.ti.com/communications

Amplifiers

Data Converters

DLP® Products

DSP

Computers and Peripherals

Consumer Electronics

Energy and Lighting

Industrial

www.ti.com/computers

www.ti.com/consumer-apps

www.ti.com/energy

dsp.ti.com

Clocks and Timers

Interface

www.ti.com/clocks

interface.ti.com

logic.ti.com

www.ti.com/industrial

www.ti.com/medical

Medical

Logic

Security

www.ti.com/security

Power Mgmt

Microcontrollers

RFID

power.ti.com

Space, Avionics and Defense

Video and Imaging

www.ti.com/space-avionics-defense

www.ti.com/video

microcontroller.ti.com

www.ti-rfid.com

www.ti.com/omap

OMAP Applications Processors

Wireless Connectivity

TI E2E Community

e2e.ti.com

www.ti.com/wirelessconnectivity

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

ADS1110A3IDBVTG4 [TI]

相关型号：

ADS1110A4IDBVR

ADS1110A4IDBVRG4

ADS1110A4IDBVT

ADS1110A4IDBVTG4

ADS1110A5IDBVR

ADS1110A5IDBVT

ADS1110A6IDBVR

ADS1110A6IDBVT

ADS1110A6IDBVTG4

ADS1110A7IDBVR

ADS1110A7IDBVT

ADS1110_10