Electronic Components Datasheet Search
English 中文版
Manufacturer Upload
Part Name:
 
Description:
X28HC256S-12  LNC56T-102  LP38856S-1.2  MC56U016HAFB-0QC00  1SS356T-12K  MC56U016HAVB-0QC00  MC56U016HBYA-0QC00  MC56U016HACB-0QC00  ECM56T-122  MC56U016HAYB-0QC00  
BQ2004E Fast-Charge ICs
Prototype PCB
Part No.:   BQ2004E
Download: Download   Right selection Save Target As
View Datasheet (Html)   No need to install PDF reader software
Description:   Fast-Charge ICs
File Size :   295 K    
Page : 19 Pages
Logo:   
Maker   TI [ TEXAS INSTRUMENTS ]http://www.ti.com
Buy Now :   
  BQ2004E Datasheet PDF page 1 BQ2004E Datasheet PDF page 2 BQ2004E Datasheet PDF page 3 BQ2004E Datasheet PDF page 5 BQ2004E Datasheet PDF page 6 BQ2004E Datasheet PDF page 7 BQ2004E Datasheet PDF page 8 BQ2004E Datasheet PDF page 9  
100%
bq2004E/H
TM1 TM2
TCO
OSC
LED1
LED2
DSEL
DCMD
DVEN
Display
Control
Timing
Control
TCO
Check
LTF
Check
VTS - VSNS
TS
Charge Control
State Machine
VBAT - VSNS
A/D
EDV
Check
SNS
Discharge
Control
MOD
Control
PWR
Control
MCV
Check
BAT
DIS
MOD
INH
VCC VSS
BD200401.eps
Figure 2. Block Diagram
The valid temperature range is V
HTF
< V
TEMP
< V
LTF
,
where:
V
LTF
= 0.4
V
CC
±
30mV
V
HTF
= [(1/3
V
LTF
) + (2/3
V
TCO
)]
±
30mV
V
TCO
is the voltage presented at the TCO input pin, and is
configured by the user with a resistor divider between V
CC
and ground. The allowed range is 0.2 to 0.4
V
CC
.
If the temperature of the battery is out of range, or the
voltage is too low, the chip enters the charge pending
state and waits for both conditions to fall within their al-
lowed limits. During the charge-pending mode, the IC
first applies a top-off charge to the battery.
The top-off charge, at the rate of 1 8 of the fast charge,
continues until the fast-charge conditions are met or the
top-off time-out period is exceeded. The IC then trickle
charges until the fast-charge conditions are met. There
is no time limit on the charge pending state; the charger
remains in this state as long as the voltage or tempera-
ture conditons are outside of the allowed limits. If the
voltage is too high, the chip goes to the battery absent
state and waits until a new charge cycle is started.
Fast charge continues until termination by one or more
of the six possible termination conditions:
n
n
n
n
n
n
Delta temperature/delta time (∆T/∆t)
Peak voltage detection (PVD)
Negative delta voltage (-∆V)
Maximum voltage
Maximum temperature
Maximum time
PVD and -∆V Termination
The bq2004E/H samples the voltage at the BAT pin once
every 34s. When -∆V termination is selected, if V
CELL
is
lower than any previously measured value by 12mV
±4mV
(6mV/cell), fast charge is terminated. When PVD
termination is selected, if V
CELL
is lower than any previ-
ously measured value by 6mV
±2mV
(3mV/cell), fast
charge is terminated. The PVD and -∆V tests are valid
in the range 0.4
V
CC
< V
CELL
< 0.8
V
CC
.
4
Home - IC Supply - Link
Copyright© 2001 - 2014 ICPDF All Rights Reserved ICPDF.COM

粤公网安备 44030402000629号


粤ICP备13051289号-7