COP8SEC516M8CMT/NOPB [TI]
IC,MICROCONTROLLER,8-BIT,COP800 CPU,CMOS,SOP,16PIN,PLASTIC;型号: | COP8SEC516M8CMT/NOPB |
厂家: | TEXAS INSTRUMENTS |
描述: | IC,MICROCONTROLLER,8-BIT,COP800 CPU,CMOS,SOP,16PIN,PLASTIC 微控制器 光电二极管 |
文件: | 总47页 (文件大小:438K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
July 1999
COP8SE Family
8-Bit CMOS ROM Based and OTP Microcontrollers with
4k Memory and 128 Bytes EERAM
RAM, one multi-function 16-bit timer/counter, idle timer with
General Description
™
MIWU, MICROWIRE/PLUS , serial I/O, crystal or R/C oscil-
The COP8SEx5 Family ROM based microcontrollers are
lator, two power saving HALT/IDLE modes, Schmitt trigger
™
highly integrated COP8
Feature core devices with 4k
™
inputs, software selectable I/O options, WATCHDOG timer
memory and advanced features including EERAM.
COP8SER7 devices are pin and software compatible (differ-
ent VCC range), 32k OTP (One Time Programmable) ver-
sions for engineering development use with a range of
COP8 software and hardware development tools.
and Clock Monitor, Low EMI 2.7V to 5.5V operation, and
16/20 pin packages.
Devices included in this data sheet are:
Family features include an 8-bit memory mapped architec-
ture, 10 MHz CKI with 1µs instruction cycle, 128 bytes of EE-
Device
OSC Memory (bytes) RAM (bytes) EERAM I/O Pins Package
Temperature
COP8SEC5
4k ROM
128
128
128
128 bytes 12/16 16/20 SOIC -40 to +85˚C, -40 to +135˚C
COP8SER7-XE xtal 32k OTP EPROM
COP8SER7-RE R/C 32k OTP EPROM
128 bytes
128 bytes
16
16
20 SOIC
20 SOIC
-40 to +85˚C, Engineering
-use only
— Software Trap
— Default VIS
Key Features
n 256 bytes data memory
— 128 bytes RAM
n Idle Timer with programmable interrupt interval
n One 16 bit timer with two 16-bit registers supporting:
— Processor Independent PWM mode
— External Event counter mode
— Input Capture mode
n 8-bit Stack Pointer SP (stack in RAM)
n Two 8-bit Register Indirect Data Memory Pointers
n Versatile instruction set
— 128 bytes EERAM
n OTP with security feature (SER7)
n Quiet Design (low radiated emissions)
n Multi-Input Wakeup pins with optional interrupts (8 pins)
n User selectable clock options:
— R/C oscillator
— Crystal oscillator
n True bit manipulation
n Memory mapped I/O
n BCD arithmetic instructions
n WATCHDOG and Clock Monitor logic
n Software selectable I/O options:
— TRI-STATE® Output:
Other Features
n Fully static CMOS, with low current drain
n Available with Crystal (-XE) or RC (-RE) oscillator
n Two power saving modes: HALT and IDLE
n 1 µs instruction cycle time
— Push-Pull Output
n 4k bytes on-board masked ROM or 32k bytes OTP
n Single supply operation: 2.7V — 5.5V
n MICROWIRE/PLUS Serial Peripheral Interface
Compatible
— Weak Pull Up Input
— High Impedance Input
n Schmitt trigger inputs on ports G and L
n Temperature ranges:
n Nine multi-source vectored interrupts servicing
— EERAM write complete
— External interrupt
— Idle Timer T0
— One Timer (with 2 Interrupts)
— −40˚C to +85˚C
— −40˚C to +135˚C (SEC5 only)
n Packaging: 16, and 20 SO (SEC5); 20 SO (SER7)
n Real time emulation and full program debug offered by
MetaLink Development System
— MICROWIRE/PLUS Serial Interface
— Multi-Input Wake Up
TRI-STATE® is a registered trademark of National Semiconductor Corporation.
™
™
™
™
MICROWIRE/PLUS , COP8 , MICROWIRE and WATCHDOG are trademarks of National Semiconductor Corporation.
™
iceMASTER is a trademark of MetaLink Corporation.
PC® is a registered trademark of International Business Machines Corporation.
© 2000 National Semiconductor Corporation
DS100973
www.national.com
Block Diagram
DS100973-44
FIGURE 1. Block Diagram
space (ROM/OTP). Selecting a microcontroller with less pro-
gram memory size translates into lower system costs, and
the added security of knowing that more code can be packed
into the available program memory space.
1.0 Device Description
1.1 ARCHITECTURE
The COP8 family is based on a modified Harvard architec-
ture, which allows data tables to be accessed directly from
program memory. This is very important with modern
microcontroller-based applications, since program memory
is usually ROM or EPROM, while data memory is usually
RAM. Consequently data tables need to be contained in
non-volatile memory, so they are not lost when the microcon-
troller is powered down. Non-memory for the storage of data
variables is provided by the EERAM in the COP8SEC5 and
COP8SER7. In a Harvard architecture, instruction fetch and
memory data transfers can be overlapped with a two stage
pipeline, which allows the next instruction to be fetched from
program memory while the current instruction is being ex-
ecuted using data memory. This is not possible with a Von
Neumann single-address bus architecture.
1.2.1 Key Instruction Set Features
The COP8 family incorporates a unique combination of in-
struction set features, which provide designers with optimum
code efficiency and program memory utilization.
Single Byte/Single Cycle Code Execution
The efficiency is due to the fact that the majority of instruc-
tions are of the single byte variety, resulting in minimum pro-
gram space. Because compact code does not occupy a sub-
stantial amount of program memory space, designers can
integrate additional features and functionality into the micro-
controller program memory space. Also, the majority instruc-
tions executed by the device are single cycle, resulting in
minimum program execution time. In fact, 77% of the instruc-
tions are single byte single cycle, providing greater code and
I/O efficiency, and faster code execution.
The COP8 family supports a software stack scheme that al-
lows the user to incorporate many subroutine calls. This ca-
pability is important when using High Level Languages. With
a hardware stack, the user is limited to a small fixed number
of stack levels.
1.2.2 Many Single-Byte, Multifunction Instructions
The COP8 instruction set utilizes many single-byte, multi-
function instructions. This enables a single instruction to ac-
complish multiple functions, such as DRSZ, DCOR, JID, LD
(Load) and X (Exchange) instructions with post-incrementing
and post-decrementing, to name just a few examples. In
many cases, the instruction set can simultaneously execute
as many as three functions with the same single-byte in-
struction.
1.2 INSTRUCTION SET
In today’s 8-bit microcontroller application arena cost/
performance, flexibility and time to market are several of the
key issues that system designers face in attempting to build
well-engineered products that compete in the marketplace.
Many of these issues can be addressed through the manner
in which a microcontroller’s instruction set handles process-
ing tasks. And that’s why the COP8 family offers a unique
and code-efficient instruction set—one that provides the
flexibility, functionality, reduced costs and faster time to mar-
ket that today’s microcontroller based products require.
JID: (Jump Indirect); Single byte instruction; decodes exter-
nal events and jumps to corresponding service routines
(analogous to “DO CASE” statements in higher level lan-
guages).
LAID: (Load Accumulator-Indirect); Single byte look up table
Code efficiency is important because it enables designers to
pack more on-chip functionality into less program memory
instruction provides efficient data path from the program
www.national.com
2
1.2.4 Register Set
1.0 Device Description (Continued)
Three memory-mapped pointers handle register indirect ad-
dressing and software stack pointer functions. The memory
data pointers allow the option of post-incrementing or post-
decrementing with the data movement instructions (LOAD/
EXCHANGE). And 15 memory-maped registers allow de-
signers to optimize the precise implementation of certain
specific instructions.
memory to the CPU. This instruction can be used for table
lookup and to read the entire program memory for checksum
calculations.
RETSK: (Return Skip); Single byte instruction allows return
from subroutine and skips next instruction. Decision to
branch can be made in the subroutine itself, saving code.
AUTOINC/DEC: (Auto-Increment/Auto-Decrement); These
instructions use the two memory pointers B and X to effi-
ciently process a block of data (analogous to “FOR NEXT” in
higher level languages).
1.3 PACKAGING/PIN EFFICIENCY
Real estate and board configuration considerations demand
maximum space and pin efficiency, particularly given today’s
high integration and small product form factors. Microcontrol-
ler users try to avoid using large packages to get the I/O
needed. Large packages take valuable board space and in-
crease device cost, two trade-offs that microcontroller de-
signs can ill afford.
1.2.3 Bit-Level Control
Bit-level control over many of the microcontroller’s I/O ports
provides a flexible means to ease layout concerns and save
board space. All members of the COP8 family provide the
ability to set, reset and test any individual bit in the data
memory address space, including memory-mapped I/O ports
and associated registers.
The COP8 family offers a wide range of packages and does
not waste pins: up to 90.9% (or 40 pins in the 44-pin pack-
age, these packages are not available on all COP8 devices)
are devoted to useful I/O.
Connection Diagrams
DS100973-6
Top View
Order Number COP8SEC516M
See NS Package Number M16B
DS100973-43
Top View
Order Number COP8SEC520M or COP8SER720M
See NS Package Number M20B
FIGURE 2. Connection Diagrams
3
www.national.com
Connection Diagrams (Continued)
Pinouts for 16-, and 20-Pin Packages
Port
L0
Type
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I
Alt. Fun
MIWU
MIWU
MIWU
MIWU
MIWU
MIWU
MIWU
MIWU
INT
20-Pin SO
16-Pin SO
7
8
7
8
L1
L2
9
9
L3
10
11
12
13
14
17
18
19
20
1
10
L4
L5
L6
L7
G0
G1
G2
G3
G4
G5
G6
G7
D0
13
14
15
16
1
WDOUT*
T1B
T1A
SO
SK
2
2
SI
3
3
I
CKO
4
4
O
D1
O
D2
O
D3
O
F0
I/O
I/O
I/O
I/O
F1
F2
F3
VCC
GND
CKI
RESET
6
15
5
6
11
5
I
I
16
12
* G1 operation as WDOUT is controlled by Mask Option.
2.1 Ordering Information
DS100973-8
FIGURE 3. Part Numbering Scheme
www.national.com
4
3.0 Electrical Characteristics
Storage Temperature
Range
−65˚C to +150˚C
ESD Protection Level
2 kV(Human Body Model)
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
ESD Protection Level
(CKI pin)
Note 1: Absolute maximum ratings indicate limits beyond which damage to
the device may occur. DC and AC electrical specifications are not ensured
when operating the device at absolute maximum ratings.
150 V(Machine Model)
Supply Voltage (VCC
Voltage at Any Pin
)
7V
Note 2: The COP8SER7 is for Engineering Development purpose only and
is not recommended for production or pre-production use.
−0.3V to VCC +0.3V
Total Current into VCC
Pin (Source)
80 mA
Total Current out of
GND Pin (Sink)
100 mA
DC Electrical Characteristics
−40˚C ≤ TA ≤ +85˚C unless otherwise specified.
Parameter
Operating Voltage
Conditions
Min
2.7
10
Typ
Max
5.5
50 x 106
Units
V
Power Supply Rise Time
ns
Power Supply Ripple (Note 4)
Supply Current (Note 5)
CKI = 10 MHz
Peak-to-Peak
0.1 Vcc
V
VCC = 5.5V, tC = 1 µs
(SEC5)
6
mA
mA
(SER7)(Note 13)
VCC = 5.5V, CKI = 0 MHz
(SEC5)
10
HALT Current (Note 6)
8
20
22
µA
µA
(SER7)
IDLE Current (Note 5)
CKI = 10 MHz
VCC = 5.5V, tC = 1 µs
(SEC5)
1.5
1.5
mA
mA
(SER7)
Input Levels (VIH, VIL)
RESET
Logic High
0.8 Vcc
0.7 Vcc
V
V
Logic Low
0.2 Vcc
CKI, All Other Inputs
Logic High
V
V
Logic Low
0.2 Vcc
+2
Hi-Z Input Leakage
Input Pullup Current
G and L Port Input Hysteresis
VCC = 5.5V
−2
µA
µA
V
VCC = 5.5V, VIN = 0V
VCC = 5.5V
−40
−250
0.25 Vcc
0.31 Vcc
VCC = 2.7V
V
5
www.national.com
DC Electrical Characteristics (Continued)
−40˚C ≤ TA ≤ +85˚C unless otherwise specified.
Parameter
Output Current Levels
Conditions
Min
Typ
Max
Units
Source (Weak Pull-Up Mode)
Source (Push-Pull Mode)
Sink (Push-Pull Mode)
VCC = 4.5V, VOH = 2.7V
VCC = 2.7V, VOH = 1.8V
VCC = 4.5V, VOH = 3.3V
VCC = 2.7V, VOH = 1.8V
VCC = 4.5V, VOL = 0.4V
VCC = 2.7V, VOL = 0.4V
VCC = 5.5V
−10
−2.5
−0.4
−0.2
1.6
−110
−33
µA
µA
mA
mA
mA
mA
µA
0.7
TRI-STATE Leakage
−2
+2
3
Allowable Sink Current per Pin
Maximum Input Current without Latchup
(Note 7)
(Note 9)
mA
mA
±
Room Temp.
200
RAM Retention Voltage, Vr
VCC Rise Time from a VCC ≥ 2.0V
Input Capacitance
(Note 9)
2
6
V
µs
(Note 9)
(Note 9)
(Note 9)
7
pF
EERAM Number of Write Cycles
EERAM Data Retention
105
cycles
years
10
www.national.com
6
AC Electrical Characteristics
−40˚C ≤ TA ≤ +85˚C unless otherwise specified.
Parameter
Instruction Cycle Time (tC)
Crystal/Resonator
Conditions
Min
Typ
Max
Units
4.5V ≤ VCC ≤ 5.5V
1
2
3
6
DC
DC
DC
DC
µs
µs
µs
µs
%
<
2.7V ≤ VCC 4.5V
R/C Oscillator
4.5V ≤ VCC ≤ 5.5V
<
2.7V ≤ VCC 4.5V
±
Frequency Variation (Note 9), (Note 10)
CKI Clock Duty Cycle (Note 9)
Rise Time (Note 9)
4.5V ≤ VCC ≤ 5.5V
fr = Max
15
45
55
%
fr = 10 MHz Ext Clock
fr = 10 MHz Ext Clock
12
8
ns
ns
ms
µs
Fall Time (Note 9)
EERAM Write Cycle
7
15
65
Delay from Power-Up to first EERAM Write
Cycle
Output Propagation Delay (Note 8)
t
PD1, tPD0
RL = 2.2k, CL = 100
pF
SO, SK
4.5V ≤ VCC ≤ 5.5V
0.7
1.75
1
µs
µs
µs
µs
ns
ns
ns
<
2.7V ≤ VCC 4.5V
All Others
4.5V ≤ VCC ≤ 5.5V
<
2.7V ≤ VCC 4.5V
2.5
MICROWIRE Setup Time (tUWS) (Note 12)
MICROWIRE Hold Time (tUWH) (Note 12)
20
56
MICROWIRE Output Propagation Delay
(tUPD)(Note 12)
220
Input Pulse Width (Note 9)
Interrupt Input High Time
Interrupt Input Low Time
Timer 1 Input High Time
Timer 1 Input Low Time
Reset Pulse Width
1
1
1
1
1
tC
tC
tC
tC
µs
Note 3: t = Instruction cycle time.
C
<
Note 4: Maximum rate of voltage change must be 0.5 V/ms.
Note 5: Supply and IDLE currents are measured with CKI driven with a square wave Oscillator, CKO driven 180˚ out of phase with CKI, inputs connected to V
CC
and outputs driven low but not connected to a load.
Note 6: The HALT mode will stop CKI from oscillating in the R/C and the Crystal configurations. In the R/C configuration, CKI is forced high internally. In the crystal
configuration, CKI is TRI-STATE. Measurement of I HALT is done with device neither sourcing nor sinking current; with L, G0, and G2–G5 programmed as low out-
DD
puts and not driving a load; all outputs programmed low and not driving a load; all inputs tied to V ; WATCHDOG and clock monitor disabled. Parameter refers to
CC
HALT mode entered via setting bit 7 of the G Port data register.
>
Note 7: Pins G6 and RESET are designed with a high voltage input network. These pins allow input voltages
V
and the pins will have sink current to V when
CC CC
>
biased at voltages
V
(the pins do not have source current when biased at a voltage below V ). The effective resistance to V
pins will not latch up. The voltage at the pins must be limited to 14V. WARNING: Voltages in excess of 14V will cause damage to the pins. This warning ex-
is 750Ω (typical). These two
CC
CC
CC
<
cludes ESD transients.
Note 8: The output propagation delay is referenced to the end of the instruction cycle where the output change occurs.
Note 9: Parameter characterized but not tested.
Note 10: Rise times faster than the minimum specification may trigger an internal power-on-reset.
Note 11: Exclusive of R and C variation.
Note 12: MICROWIRE Setup and Hold Times and Propagation Delays are referenced to the appropriate edge of the MICROWIRE clock. See Figure 4 and the MI-
CROWIRE operation description.
Note 13: COP7SER7 Supply Current during Reset will be somewhat higher.
7
www.national.com
Absolute Maximum Ratings (Note 14)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Storage Temperature Range
ESD Protection Level
−65˚C to +150˚C
2kV (Human Body
Model)
ESD Protection Level (CKI
pin)
150 V (Machine
Model)
Supply Voltage (VCC
Voltage at Any Pin
)
7V
Note 14: Absolute maximum ratings indicate limits beyond which damage to
the device may occur. DC and AC electrical specifications are not ensured
when operating the device at absolute maximum ratings.
−0.3V to VCC +0.3V
Total Current into VCC Pin
(Source)
Note 15: The COP8SER7 is for Engineering Development purpose only and
is not recommended for production or pre-production use.
80 mA
Total Current out of GND Pin
(Sink)
100 mA
DC Electrical Characteristics (SEC5 only)
−40˚C ≤ TA ≤ +135˚C unless otherwise specified.
Parameter
Conditions
Min
4.5
10
Typ
Max
5.5
50 x 106
Units
V
Operating Voltage
Power Supply Rise Time
Power Supply Ripple (Note 17)
Supply Current (Note 18)
CKI = 10 MHz
ns
Peak-to-Peak
0.1 Vcc
V
VCC = 5.5V, tC = 1 µs
8
mA
µA
HALT Current (Note 19)
IDLE Current (Note 18)
CKI = 10 MHz
VCC = 5.5V, CKI = 0 MHz
15
50
VCC = 5.5V, tC = 1 µs
2
mA
Input Levels (VIH, VIL)
RESET
Logic High
0.8 Vcc
0.7 Vcc
V
V
Logic Low
0.2 Vcc
CKI, All Other Inputs
Logic High
V
V
Logic Low
0.2 Vcc
+5
Hi-Z Input Leakage
Input Pullup Current
G and L Port Input Hysteresis
VCC = 5.5V
−5
µA
µA
V
VCC = 5.5V, VIN = 0V
VCC = 5.5V
−35
−400
0.25
Vcc
Output Current Levels
Source (Weak Pull-Up Mode)
Source (Push-Pull Mode)
Sink (Push-Pull Mode)
VCC = 4.5V, VOH = 2.7V
VCC = 4.5V, VOH = 3.3V
VCC = 4.5V, VOL = 0.4V
VCC = 5.5V
−9.0
−0.4
1.6
−140
+5
µA
mA
mA
µA
TRI-STATE Leakage
−5
Allowable Sink Current per Pin (Note 22)
Maximum Input Current without Latchup (Note
20)
Room Temp.
±
200
7
mA
RAM Retention Voltage, Vr
VCC Rise Time from a VCC ≥ 2.0V
Input Capacitance
2.0
6
V
µs
(Note 23)
(Note 22)
(Note 22)
(Note 22)
pF
EERAM Number of Write Cycles
EERAM Data Retention
105
cycles
years
10
www.national.com
8
AC Electrical Characteristics
−40˚C ≤ TA ≤ +135˚C unless otherwise specified.
Parameter
Instruction Cycle Time (tC)
Crystal/Resonator, External
R/C Oscillator (Internal)
Conditions
Min
Typ
Max
Units
4.5V ≤ VCC ≤ 5.5V
4.5V ≤ VCC ≤ 5.5V
4.5V ≤ VCC ≤ 5.5V
fr = Max
1
3
DC
DC
µs
µs
%
±
Frequency Variation (Note 22), (Note 21)
CKI Clock Duty Cycle (Note 22)
Rise Time (Note 22)
20
45
55
%
fr = 10 MHz Ext Clock
fr = 10 MHz Ext Clock
12
8
ns
ns
ms
µs
Fall Time (Note 22)
EERAM Write Cycle
7
15
65
Delay from Power-up to first EERAM Write
Cycle
Output Propagation Delay (Note 21)
RL = 2.2k, CL = 100
pF
tPD1, tPD0
SO, SK
4.5V ≤ VCC ≤ 5.5V
4.5V ≤ VCC ≤ 5.5V
0.7
1.0
µs
µs
ns
ns
ns
All Others
MICROWIRE Setup Time (tUWS) (Note 25)
MICROWIRE Hold Time (tUWH) (Note 25)
20
56
MICROWIRE Output Propagation Delay
(tUPD) (Note 25)
220
Input Pulse Width (Note 22)
Interrupt Input High Time
Interrupt Input Low Time
Timer 1 Input High Time
Timer 1 Input Low Time
Reset Pulse Width
1
1
1
1
1
tC
tC
tC
tC
µs
Note 16: t = Instruction cycle time.
C
<
Note 17: Maximum rate of voltage change must be 0.5 V/ms.
Note 18: Supply and IDLE currents are measured with CKI driven with a square wave Oscillator, CKO driven 180˚ out of phase with CKI, inputs connected to V
CC
and outputs driven low but not connected to a load.
Note 19: The HALT mode will stop CKI from oscillating in the R/C and the Crystal configurations. In the R/C configuration, CKI is forced high internally. In the crystal
configuration, CKI is TRI-STATE. Measurement of I HALT is done with device neither sourcing nor sinking current; with L, G0, and G2–G5 programmed as low out-
DD
puts and not driving a load; all outputs programmed low and not driving a load; all inputs tied to V ; clock monitor disabled. Parameter refers to HALT mode entered
CC
via setting bit 7 of the G Port data register.
>
Note 20: Pins G6 and RESET are designed with a high voltage input network. These pins allow input voltages
V
and the pins will have sink current to V when
CC CC
>
biased at voltages
V
(the pins do not have source current when biased at a voltage below V ). The effective resistance to V
pins will not latch up. The voltage at the pins must be limited to 14V. WARNING: Voltages in excess of 14V will cause damage to the pins. This warning excludes
ESD transients.
is 750Ω (typical). These two
CC
CC
CC
<
Note 21: The output propagation delay is referenced to the end of the instruction cycle where the output change occurs.
Note 22: Parameter characterized but not tested.
Note 23: Rise times faster than the minimum specification may trigger an internal power-on-reset.
Note 24: Exclusive of R and C variation.
Note 25: MICROWIRE Setup and Hold Times and Propagation Delays are referenced to the appropriate edge of the MICROWIRE clock. See Figure 4 and the MI-
CROWIRE operation description.
DS100973-9
FIGURE 4. MICROWIRE/PLUS Timing
9
www.national.com
Port G is an 8-bit port. Pin G0, G2–G5 are bi-directional I/O
ports. Pin G6 is always a general purpose Hi-Z input. All pins
have Schmitt Triggers on their inputs. Pin G1 serves as the
dedicated WATCHDOG output with weak pullup, if
WATCHDOG feature is selected by the mask option. The
pin is a general purpose I/O, if WATCHDOG feature is not
selected. If WATCHDOG feature is selected, bit 1 of the Port
G configuration and data register does not have any effect
on Pin G1 setup. Pin G7 is either input or output depending
on the oscillator option selected. With the crystal oscillator
option selected, G7 serves as the dedicated output pin for
the CKO clock output. With the R/C oscillator option se-
lected, G7 serves as a general purpose Hi-Z input pin and is
also used to bring the device out of HALT mode with a low to
high transition on G7.
4.0 Pin Descriptions
The device I/O structure enables designers to reconfigure
the microcontroller’s I/O functions with a single instruction.
Each individual I/O pin can be independently configured as
output pin low, output high, input with high impedance or in-
put with weak pull-up device. A typical example is the use of
I/O pins as the keyboard matrix input lines. The input lines
can be programmed with internal weak pull-ups so that the
input lines read logic high when the keys are all open. With
a key closure, the corresponding input line will read a logic
zero since the weak pull-up can easily be overdriven. When
the key is released, the internal weak pull-up will pull the in-
put line back to logic high. This eliminates the need for exter-
nal pull-up resistors. The high current options are available
for driving LEDs, motors and speakers. This flexibility helps
to ensure a cleaner design, with fewer external components
and lower costs. Below is the general description of all avail-
able pins.
Since G6 is an input only pin and G7 is the dedicated CKO
clock output pin (crystal clock option) or general purpose in-
put (R/C or clock option), the associated bits in the data and
configuration registers for G6 and G7 are used for special
purpose functions as outlined below. Reading the G6 and G7
data bits will return zeroes.
VCC and GND are the power supply pins. All VCC and GND
pins must be connected.
CKI is the clock input. This can come from the Internal R/C
oscillator, or a crystal oscillator (in conjunction with CKO).
See Oscillator Description section.
Each device will be placed in the HALT mode by writing a “1”
to bit 7 of the Port G Data Register. Similarly the device will
be placed in the IDLE mode by writing a “1” to bit 6 of the
Port G Data Register.
RESET is the master reset input. See Reset description sec-
tion.
Writing a “1” to bit 6 of the Port G Configuration Register en-
ables the MICROWIRE/PLUS to operate with the alternate
phase of the SK clock. The G7 configuration bit, if set high,
enables the clock start up delay after HALT when the R/C
clock configuration is used.
Each device contains two bidirectional 8-bit I/O ports (G and
L) and one bidirectional 4-I/O port (F), where each individual
bit may be independently configured as an input (Schmitt
trigger inputs on ports L and G), output or TRI-STATE under
program control. Three data memory address locations are
allocated for each of these I/O ports. Each I/O port has two
associated 8-bit memory mapped registers, the CONFIGU-
RATION register and the output DATA register. A memory
mapped address is also reserved for the input pins of each
I/O port. (See the memory map for the various addresses as-
sociated with the I/O ports.) Figure 5 shows the I/O port con-
figurations. The DATA and CONFIGURATION registers allow
for each port bit to be individually configured under software
control as shown below:
Config. Reg.
CLKDLY
Alternate SK
Data Reg.
HALT
IDLE
G7
G6
Port G has the following alternate features:
G7 CKO Oscillator dedicated output or general purpose in-
put
G6 SI (MICROWIRE Serial Data Input)
G5 SK (MICROWIRE Serial Clock)
G4 SO (MICROWIRE Serial Data Output)
G3 T1A (Timer T1 I/O)
CONFIGURATION
Register
DATA
Port Set-Up
Hi-Z Input
Register
0
0
G2 T1B (Timer T1 Capture Input)
(TRI-STATE Output)
Input with Weak Pull-Up
Push-Pull Zero Output
Push-Pull One Output
G1 WDOUT WATCHDOG and/or CLock Monitor if WATCH-
DOG enabled, otherwise it is a general purpose I/O
(General purpose I/O is not available on COP8SER7)
0
1
1
1
0
1
G0 INTR (External Interrupt Input)
Port L is an 8-bit I/O port. All L-pins have Schmitt triggers on
the inputs.
Port L supports the Multi-Input Wake Up feature on all eight
pins.
DS100973-10
FIGURE 5. I/O Port Configurations
www.national.com
10
SP is the 8-bit stack pointer, which points to the subroutine/
interrupt stack (in RAM). With reset the SP is initialized to
RAM address 02F Hex (devices with 64 bytes of RAM), or
initialized to RAM address 06F Hex (devices with 128 bytes
of RAM).
4.0 Pin Descriptions (Continued)
All the CPU registers are memory mapped with the excep-
tion of the Accumulator (A) and the Program Counter (PC).
5.2 PROGRAM MEMORY
The program memory consists of 4096 Bytes of ROM or
32,768 bytes of OTP EPROM. These bytes may hold pro-
gram instructions or constant data (data tables for the LAID
instruction, jump vectors for the JID instruction, and interrupt
vectors for the VIS instruction). The program memory is ad-
dressed by the 15-bit program counter (PC). All interrupts in
the device vector to program memory location 0FF Hex. The
contents of the program memory read 00 Hex in the erased
state. Program execution starts at location 0 after RESET.
DS100973-12
FIGURE 6. I/O Port Configurations—Output Mode
5.3 DATA MEMORY
The data memory address space includes the on-chip RAM
and data registers, the I/O registers (Configuration, Data and
Pin), the control registers, the MICROWIRE/PLUS SIO shift
register, and the various registers, and counters associated
with the timers (with the exception of the IDLE timer). Data
memory is addressed directly by the instruction or indirectly
by the B, X and SP pointers.
The data memory consists of 256 bytes of combined EE-
RAM and RAM. Sixteen bytes of RAM are mapped as “reg-
isters” at addresses 0F0 to 0FE Hex. These registers can be
loaded immediately, and also decremented and tested with
the DRSZ (decrement register and skip if zero) instruction.
The memory pointer registers X, SP and B are memory
mapped into this space at address locations 0FC to 0FE Hex
respectively, with the other registers (except 0FF) being
available for general usage.
DS100973-11
FIGURE 7. I/O Port Configurations—Input Mode
The instruction set permits any bit in memory to be set, reset
or tested. All I/O and registers (except A and PC) are
memory mapped; therefore, I/O bits and register bits can be
directly and individually set, reset and tested. The accumula-
tor (A) bits can also be directly and individually tested.
Note: RAM contents are undefined upon power-up.
5.0 Functional Description
The architecture of the devices is a modified Harvard archi-
tecture. With the Harvard architecture, the program memory
ROM or EPROM is separated from the data store memory
(RAM). Program Memory will be referred to as ROM. Both
ROM and RAM have their own separate addressing space
with separate address buses. The architecture, though
based on the Harvard architecture, permits transfer of data
from ROM to RAM.
5.4 EERAM / NON-VOLATILE MEMORY
The devices provide 128 bytes of EERAM in segment 1 for
nonvolatile data memory. The data EERAM can be read and
written in exactly the same way as the RAM. All instructions
that perform read and write operations on the RAM work
similarly upon the data EERAM. EERAM write cycles take
much more time than reads. During this time, processing
continues, but all EERAM accesses are inhibited. The data
EERAM contains all 00s when shipped by the factory.
5.1 CPU REGISTERS
The CPU can do an 8-bit addition, subtraction, logical or shift
operation in one instruction (tC) cycle time.
There are six CPU registers:
A data memory EERAM programming cycle is initiated by an
instruction that writes to the EERAM such as X, LD, SBIT
and RBIT. The EERAM memory support circuitry sets the
E2BUSY flag in the E2CFG register immediately upon begin-
ning a data EERAM write cycle. It will be automatically reset
by the hardware at the end of the data EERAM write cycle.
The application program should test the E2BUSY flag before
attempting a read or write operation to the data EERAM. An
EERAM read or write operation while an operation is in
progress will be ignored and the E2ILRW flag in the E2CFG
register will be set to indicate the error status. Once the write
operation starts, nothing will stop the write operation, not by
resetting the device, and not even turning off the VCC will
guarantee the write operation to stop.
A is the 8-bit Accumulator Register
PC is the 15-bit Program Counter Register
PU is the upper 7 bits of the program counter (PC)
PL is the lower 8 bits of the program counter (PC)
B is an 8-bit RAM address pointer, which can be optionally
post auto incremented or decremented.
X is an 8-bit alternate RAM address pointer, which can be
optionally post auto incremented or decremented.
S is the 8-bit Segment Address Register used to extend the
lower half of the address range (00 to 7F) into 256 data seg-
ments of 128 bytes each.
11
www.national.com
The data store memory is either addressed directly by a
single byte address within the instruction, or indirectly rela-
tive to the reference of the B, X, or SP pointers (each con-
tains a single-byte address). This single-byte address allows
an addressing range of 256 locations from 00 to FF hex. The
upper bit of this single-byte address divides the data store
memory into two separate sections as outlined previously.
With the exception of the RAM register memory from ad-
dress locations 00F0 to 00FF, all RAM memory is memory
mapped with the upper bit of the single-byte address being
equal to zero. This allows the upper bit of the single-byte ad-
dress to determine whether or not the base address range
(from 0000 to 00FF) is extended. If this upper bit equals one
(representing address range 0080 to 00FF), then address
extension does not take place. Alternatively, if this upper bit
equals zero, then the data segment extension register S is
used to extend the base address range (from 0000 to 007F)
from XX00 to XX7F, where XX represents the 8 bits from the
S register. Thus the 128-byte data segment extensions are
located from addresses 0100 to 017F for data segment 1,
0200 to 027F for data segment 2, etc., up to FF00 to FF7F
for data segment 255. The base address range from 0000 to
007F represents data segment 0.
5.0 Functional Description (Continued)
Caution: In order to prevent the unexpected setting of the ILRW of the
E2CFG Register and the corresponding interrupt, the use of the X
Register and direct addressing are recommanded for EERAM ac-
cess. It is further recommended that the B Register be set to a
value between 80 (hex) and FF (hex) before setting the Segment
register to 1 and that this value be retained until S is set back to 0.
Due to an artifact of the COP8 architecture, the ILRW bit of the
E2CFG Register will be set and an interrupt will be generated un-
der the following conditions:
1. The Segment Register (S) = 01,
and
2. The B Register points to the EERAM, i.e. B ≤7F (hex),
and
3. One of the following instructions is executed: SC, RC, IFC, IFNC, NOP,
RPND, SWAPA, JMPL, VIS or LD B, Imm with Imm ≤7F (hex),
or
3a. if any instruction is skipped.
Warning: The segment register should not point to the EE-
RAM unless the EERAM is addressed. This will prevent in-
advertent writes to EERAM.
5.4.1. E2CFG and EE Support Circuitry
Figure 8 illustrates how the S register data memory exten-
sion is used in extending the lower half of the base address
range (00 to 7F hex) into 256 data segments of 128 bytes
each, with a total addressing range of 32 kbytes from XX00
to XX7F. This organization allows a total of 256 data seg-
ments of 128 bytes each with an additional upper base seg-
ment of 128 bytes. Furthermore, all addressing modes are
available for all data segments. The S register must be
changed under program control to move from one data seg-
ment (128 bytes) to another. However, the upper base seg-
ment (containing the 16 memory registers, I/O registers,
control registers, etc.) is always available regardless of the
contents of the S register, since the upper base segment
(address range 0080 to 00FF) is independent of data seg-
ment extension.
The EERAM module contains EERAM support circuits to
generate all necessary high voltage programming pulses.
The E2CFG register provides control and status functions for
the EERAM module. The E2CFG register bit assignments
are shown below. The E2CFG register is set to 0 on RESET
except the E2BUSY bit, which is unaffected. The EECFG
register can be accessed at any time without error.
Reserved, must be 0
R/W R/W R/W R/W
Bit 7
E2PEND E2ILRW E2BUSY E2EI
R/W
R/W
RO
R/W
Bit 0
RESERVED These bits are reserved and must be 0.
E2PEND
Interrupt Pending Bit. This bit indicates that
a write operation has completed and a Write
Complete Interrupt is pending. This bit is
logically ANDed with the E2EI bit to cause
an interrupt. This bit can be written by either
hardware or software. This bit must be reset
by software after processing the interrupt.
E2ILRW
EERAM illegal read/write operation. This bit
is set when the EERAM array is accessed
while E2BUSY is set. This bit will cause an
EERAM interrupt, without setting the
E2PEND bit, if the E2EI bit is set. This bit
can be written by either hardware or soft-
ware. This bit must be reset by software af-
ter processing the interrupt.
E2BUSY
E2EI
This bit is set by the hardware when a write
to the EERAM is in process and reset by the
hardware when the write completes. The
E2PEND bit is set when this bit is reset.
This bit is software read-only.
Interrupt Enable Bit. Setting this bit enables
EERAM interrupts. The default condition is
interrupts disabled after RESET. This bit
must be used in conjunction with the GIE
bit. This bit can be written by software only.
DS100973-45
5.5 DATA MEMORY SEGMENT RAM EXTENSION
FIGURE 8. RAM Organization
Data memory address 0FF is used as a memory mapped lo-
cation for the Data Segment Address Register (S).
The instructions that utilize the stack pointer (SP) always ref-
erence the stack as part of the base segment (Segment 0),
regardless of the contents of the S register. The S register is
www.national.com
12
S Register: CLEARED
5.0 Functional Description (Continued)
E2CFG: Cleared except the E2BUSY Bit (Bit 1)
EERAM: Unaffected
not changed by these instructions. Consequently, the stack
(used with subroutine linkage and interrupts) is always lo-
cated in the base segment. The stack pointer will be initial-
ized to point at data memory location 006F as a result of re-
set.
ITMR: Cleared
RAM:
UNAFFECTED after RESET with power already applied
RANDOM after RESET at power-on
WATCHDOG (if enabled):
The 128 bytes of RAM contained in the base segment are
split between the lower and upper base segments. The first
112 bytes of RAM are resident from address 0000 to 006F in
the lower base segment, while the remaining 16 bytes of
RAM represent the 16 data memory registers located at ad-
dresses 00F0 to 00FF of the upper base segment. No RAM
is located at the upper sixteen addresses (0070 to 007F) of
the lower base segment.
The device comes out of reset with both the WATCH-
DOG logic and the Clock Monitor detector armed, with the
WATCHDOG service window bits set and the Clock Monitor
bit set. The WATCHDOG and Clock Monitor circuits are in-
hibited during reset. The WATCHDOG service window bits
being initialized high default to the maximum WATCHDOG
service window of 64k tC clock cycles. The Clock Monitor bit
being initialized high will cause a Clock Monitor error follow-
ing reset if the clock has not reached the minimum specified
frequency at the termination of reset. A Clock Monitor error
will cause an active low error output on pin G1. This error
output will continue until 16 tC–32 tC clock cycles following
the clock frequency reaching the minimum specified value,
at which time the G1 output will go high.
Additional RAM beyond these initial 128 bytes, however, will
always be memory mapped in groups of 128 bytes (or less)
at the data segment address extensions (XX00 to XX7F) of
the lower base segment. The 128 bytes of EERAM in this de-
vice are memory mapped at address locations 0100 to 017F.
5.6 SECURITY FEATURE (COP8SER7 only)
The program memory array has an associated Security Byte
that is located outside of the program address range. This
byte can be addressed only from programming mode by a
programmer tool.
5.8.1 External Reset
The RESET input when pulled low initializes the device. The
RESET pin must be held low for a minimum of one instruc-
tion cycle to guarantee a valid reset. During Power-Up initial-
ization, the user must ensure that the RESET pin is held low
until the device is within the specified VCC voltage. An R/C
circuit on the RESET pin with a delay 5 times (5x) greater
than the power supply rise time is recommended. Reset
should also be wide enough to ensure crystal start-up upon
Power-Up.
Security is an optional feature and can only be asserted after
the memory array has been programmed and verified. A se-
cured part will read 00(hex) by a programmer. The part will
fail Blank Check and will fail Verify operations. A READ op-
eration will fill the programmer’s memory with 00(hex). The
Security Byte itself is always readable with value of 00(hex)
if unsecure and FF(hex) if secure.
5.7 RESET
RESET may also be used to cause an exit from the HALT
mode.
The devices are initialized when the RESET pin is pulled low.
The following occurs upon initialization:
Port L: TRI-STATE (High Impedance Input)
Port G: TRI-STATE (High Impedance Input)
PC: CLEARED to 0000
A recommended reset circuit for this device is shown in Fig-
ure 9.
PSW, CNTRL and ICNTRL registers: CLEARED
SIOR:
UNAFFECTED after RESET with power already applied
RANDOM after RESET at power-on
Accumulator, Timer 1:
DS100973-14
RANDOM after RESET with crystal clock option
(power already applied)
>
RC 5x power supply rise time.
FIGURE 9. Reset Circuit Using External Reset
UNAFFECTED after RESET with R/C clock option
(power already applied)
5.9 OSCILLATOR CIRCUITS
RANDOM after RESET at power-on
WKEN, WKEDG: CLEARED
These devices can be driven by a clock input on the CKI in-
put pin which can be between DC and 10 MHz. The CKO
output clock is on pin G7 (crystal configuration). The CKI in-
put frequency is divided down by 10 to produce the instruc-
tion cycle clock (1/tC ).
WKPND: RANDOM
SP (Stack Pointer):
Initialized to RAM address 06F Hex
B and X Pointers:
Figure 10 shows the crystal and R/C oscillator connection
diagram.
UNAFFECTED after RESET with power already applied
RANDOM after RESET at power-on
13
www.national.com
5.0 Functional Description (Continued)
DS100973-51
DS100973-50
FIGURE 10. Crystal and R/C Oscillator
5.9.2 R/C Oscillator
5.9.1 Crystal Oscillator
CKI and CKO can be connected to make a closed loop crys-
tal (or resonator) controlled oscillator.
By selecting CKI as a single pin oscillator input, a single pin
R/C oscillator circuit can be connected to it. CKO is available
as a general purpose input, and /or HALT restart input.
Table 1 shows the component values required for various
standard crystal values.
Table 2 shows the variation in the oscillator frequency as a
function of the component (R and C) value.
TABLE 1. Crystal Oscillator Configuration,
TA = 25˚C, VCC = 5V
TABLE 2. R/C Oscillator Configuration,
TA = 25˚C, VCC = 5V
CKI Freq.
R1 (kΩ)
R2 (MΩ)
C1 (pF)
C2 (pF)
R (kΩ)
3.3
C (pF)
82
CKI Freq.(MHz)
2.2 to 2.7
Instr. Cycle (µs)
3.7 to 4.6
(MHz)
10
0
0
1
1
1
32
39
32
39
5.6
100
1.1 to 1.3
7.4 to 9.0
4
6.8
100
0.9 to 1.1
8.8 to 10.8
5.6
100
100–156
0.455
www.national.com
14
5.0 Functional Description (Continued)
6.0 Timers
Each device contains a very versatile set of timers (T0 and
T1). All timers and associated autoreload/capture registers
power up containing random data.
5.10 CONTROL REGISTERS
CNTRL Register (Address X'00EE)
T1C3
Bit 7
T1C2
T1C1
T1C0 MSEL
IEDG
SL1
SL0
6.1 TIMER T0 (IDLE TIMER)
Bit 0
Each device supports applications that require maintaining
real time and low power with the IDLE mode. This IDLE
mode support is furnished by the IDLE timer T0, which is a
16-bit timer. The Timer T0 runs continuously at the fixed rate
of the instruction cycle clock, tC. The user cannot read or
write to the IDLE Timer T0, which is a count down timer.
The Timer1 (T1) and MICROWIRE/PLUS control register
contains the following bits:
T1C3
T1C2
T1C1
T1C0
Timer T1 mode control bit
Timer T1 mode control bit
Timer T1 mode control bit
Timer T1 Start/Stop control in timer
The Timer T0 supports the following functions:
•
•
•
Exit out of the Idle Mode (See Idle Mode description)
WATCHDOG logic (See WATCHDOG description)
Start up delay out of the HALT mode
modes 1 and 2, T1 Underflow Interrupt
Pending Flag in timer mode 3
MSEL
IEDG
Selects G5 and G4 as MICROWIRE/PLUS
signals SK and SO respectively
Figure 11 is a functional block diagram showing the structure
of the IDLE Timer and its associated interrupt logic.
External interrupt edge polarity select
(0 = Rising edge, 1 = Falling edge)
Bits 11 through 15 of the Idle Timer register can be selected
for triggering the IDLE Timer interrupt. Each time the se-
lected bit underflows (every 4k, 8k, 16k, 32k or 64k instruc-
tion cycles), the IDLE Timer interrupt pending bit T0PND is
set, thus generating an interrupt (if enabled), and bit 6 of the
Port G data register is reset, thus causing an exit from the
IDLE mode if the device is in that mode.
SL1 & SL0 Select the MICROWIRE/PLUS clock divide
by (00 = 2, 01 = 4, 1x = 8)
PSW Register (Address X'00EF)
HC
C
T1PNDA T1ENA EXPND BUSY EXEN GIE
Bit 0
In order for an interrupt to be generated, the IDLE Timer in-
terrupt enable bit T0EN must be set, and the GIE (Global In-
terrupt Enable) bit must also be set. The T0PND flag and
T0EN bit are bits 5 and 4 of the ICNTRL register, respec-
tively. The interrupt can be used for any purpose. Typically, it
is used to perform a task upon exit from the IDLE mode. For
more information on the IDLE mode, refer to the Power Save
Modes section.
Bit 7
The PSW register contains the following bits:
HC
C
Half Carry Flag
Carry Flag
T1PNDA Timer T1 Interrupt Pending Flag (Autoreload
RA in mode 1, T1 Underflow in Mode 2, T1A
capture edge in mode 3)
The Idle Timer period is selected by bits 0–2 of the ITMR
register Bits 3–7 of the ITMR Register are reserved and
must be “0”.
T1ENA
Timer T1 Interrupt Enable for Timer Underflow
or T1A Input capture edge
EXPND External interrupt pending
BUSY
EXEN
GIE
MICROWIRE/PLUS busy shifting flag
TABLE 3. Idle Timer Window Length
Enable external interrupt
ITSEL2
ITSEL1
ITSEL0
Idle Timer Period
(Instruction Cycles)
4,096
Global interrupt enable (enables interrupts)
The Half-Carry flag is also affected by all the instructions that
affect the Carry flag. The SC (Set Carry) and R/C (Reset
Carry) instructions will respectively set or clear both the carry
flags. In addition to the SC and R/C instructions, ADC,
SUBC, RRC and RLC instructions affect the Carry and Half
Carry flags.
0
0
0
0
1
0
0
1
1
X
0
1
0
1
X
8,192
16,384
32,768
65,536
ICNTRL Register (Address X'00E8)
The ITMR register is cleared on Reset and the Idle Timer pe-
riod is reset to 4,096 instruction cycles.
Reserved
Bit 7
LPEN
T0PND
T0EN µWPND µWEN T1PNDB
T1ENB
Bit 0
The ICNTRL register contains the following bits:
Reserved This bit is reserved and must be set to zero
ITMR Register (Address X’0xCF)
Reserved (Must be ″0″)
ITSEL2
ITSEL1
ITSEL0
Bit 0
LPEN
L Port Interrupt Enable (Multi-Input Wakeup/
Interrupt)
Bit 7
Bit 3
Any time the IDLE Timer period is changed there is the pos-
sibility of generating a spurious IDLE Timer interrupt by set-
ting the T0PND bit. The user is advised to disable IDLE
Timer interrupts prior to changing the value of the ITSEL bits
of the ITMR Register and then clear the T0PND bit before at-
tempting to synchronize operation to the IDLE Timer.
T0PND
T0EN
Timer T0 Interrupt pending
Timer T0 Interrupt Enable (Bit 12 toggle)
MICROWIRE/PLUS interrupt pending
Enable MICROWIRE/PLUS interrupt
µWPND
µWEN
T1PNDB Timer T1 Interrupt Pending Flag for T1B cap-
ture edge
T1ENB
Timer T1 Interrupt Enable for T1B Input cap-
ture edge
15
www.national.com
6.0 Timers (Continued)
DS100973-52
FIGURE 11. Functional Block Diagram for Idle Timer T0
6.2 TIMER T1
the register R1A. Subsequent underflows cause the timer to
be reloaded from the registers alternately beginning with the
register R1B.
The device has a powerful timer/counter block. The timer
consists of a 16-bit timer, T1, and two supporting 16-bit
autoreload/capture registers, R1A and R1B. The timer block
has two pins associated with it, T1A and T1B. The pin T1A
supports I/O required by the timer block, while the pin T1B is
an input to the timer block. The powerful and flexible timer
block allows the device to easily perform all timer functions
with minimal software overhead. The timer block has three
operating modes: Processor Independent PWM mode, Ex-
ternal Event Counter mode, and Input Capture mode.
The T1 Timer control bits, T1C3, T1C2 and T1C1 set up the
timer for PWM mode operation.
Figure 12 shows a block diagram of the timer in PWM mode.
The underflows can be programmed to toggle the T1A output
pin. The underflows can also be programmed to generate in-
terrupts.
Underflows from the timer are alternately latched into two
pending flags, T1PNDA and T1PNDB. The user must reset
these pending flags under software control. Two control en-
able flags, T1ENA and T1ENB, allow the interrupts from the
timer underflow to be enabled or disabled. Setting the timer
enable flag T1ENA will cause an interrupt when a timer un-
derflow causes the R1A register to be reloaded into the
timer. Setting the timer enable flag T1ENB will cause an in-
terrupt when a timer underflow causes the R1B register to be
reloaded into the timer. Resetting the timer enable flags will
disable the associated interrupts.
The control bits T1C3, T1C2, and T1C1 allow selection of the
different modes of operation.
6.2.1 Mode 1. Processor Independent PWM Mode
As the name suggests, this mode allows the device to gen-
erate a PWM signal with very minimal user intervention. The
user only has to define the parameters of the PWM signal
(ON time and OFF time). Once begun, the timer block will
continuously generate the PWM signal completely indepen-
dent of the microcontroller. The user software services the
timer block only when the PWM parameters require updat-
ing.
Either or both of the timer underflow interrupts may be en-
abled. This gives the user the flexibility of interrupting once
per PWM period on either the rising or falling edge of the
PWM output. Alternatively, the user may choose to interrupt
on both edges of the PWM output.
In this mode the timer T1 counts down at a fixed rate of tC.
Upon every underflow the timer is alternately reloaded with
the contents of supporting registers, R1A and R1B. The very
first underflow of the timer causes the timer to reload from
www.national.com
16
6.0 Timers (Continued)
DS100973-46
FIGURE 12. Timer in PWM Mode
6.2.2 Mode 2. External Event Counter Mode
6.2.3 Mode 3. Input Capture Mode
This mode is quite similar to the processor independent
PWM mode previously described. The main difference is that
the timer, T1, is clocked by the input signal from the T1A pin.
The T1 timer control bits, T1C3, T1C2 and T1C1 allow the
timer to be clocked either on a positive or negative edge from
the T1A pin. Underflows from the timer are latched into the
T1PNDA pending flag. Setting the T1ENA control flag will
cause an interrupt when the timer underflows.
The device can precisely measure external frequencies or
time external events by placing the timer block, T1, in the in-
put capture mode.
In this mode, the timer T1 is constantly running at the fixed tC
rate. The two registers, R1A and R1B, act as capture regis-
ters. Each register acts in conjunction with a pin. The register
R1A acts in conjunction with the T1A pin and the register
R1B acts in conjunction with the T1B pin.
In this mode the input pin T1B can be used as an indepen-
dent positive edge sensitive interrupt input if the T1ENB con-
trol flag is set. The occurrence of a positive edge on the T1B
input pin is latched into the T1PNDB flag.
The timer value gets copied over into the register when a
trigger event occurs on its corresponding pin. Control bits,
T1C3, T1C2 and T1C1, allow the trigger events to be speci-
fied either as a positive or a negative edge. The trigger con-
dition for each input pin can be specified independently.
Figure 13 shows a block diagram of the timer in External
Event Counter mode.
The trigger conditions can also be programmed to generate
interrupts. The occurrence of the specified trigger condition
on the T1A and T1B pins will be respectively latched into the
pending flags, T1PNDA and T1PNDB. The control flag
T1ENA allows the interrupt on T1A to be either enabled or
disabled. Setting the T1ENA flag enables interrupts to be
generated when the selected trigger condition occurs on the
T1A pin. Similarly, the flag T1ENB controls the interrupts
from the T1B pin.
Note: The PWM output is not available in this mode since the T1A pin is be-
ing used as the counter input clock.
Underflows from the timer can also be programmed to gen-
erate interrupts. Underflows are latched into the timer T1C0
pending flag (the T1C0 control bit serves as the timer under-
flow interrupt pending flag in the Input Capture mode). Con-
sequently, the T1C0 control bit should be reset when enter-
ing the Input Capture mode. The timer underflow interrupt is
enabled with the T1ENA control flag. When a T1A interrupt
occurs in the Input Capture mode, the user must check both
the T1PNDA and T1C0 pending flags in order to determine
whether a T1A input capture or a timer underflow (or both)
caused the interrupt.
DS100973-47
FIGURE 13. Timer in External Event Counter Mode
Figure 14 shows a block diagram of the timer in Input Cap-
ture Mode.
17
www.national.com
6.0 Timers (Continued)
DS100973-48
FIGURE 14. Timer in Input Capture Mode
T1PNDA Timer Interrupt Pending Flag
6.3 TIMER CONTROL FLAGS
The Timer T1 control bits and their functions are summarized
below.
T1ENA
Timer Interrupt Enable Flag
1 = Timer Interrupt Enabled
0 = Timer Interrupt Disabled
T1C3
T1C2
T1C1
T1C0
Timer mode control
Timer mode control
Timer mode control
T1PNDB Timer Interrupt Pending Flag
T1ENB
Timer Interrupt Enable Flag
1 = Timer Interrupt Enabled
0 = Timer Interrupt Disabled
Timer Start/Stop control in Modes 1 and 2 (Pro-
cessor Independent PWM and External Event
Counter), where 1 = Start, 0 = Stop Timer Under-
flow Interrupt Pending Flag in Mode 3 (Input Cap-
ture)
The timer mode control bits (T1C3, T1C2 and T1C1) are detailed below:
Interrupt A
Source
Interrupt B
Source
Timer
Mode
T1C3
T1C2
T1C1
Description
Counts On
1
1
0
0
1
0
PWM: T1A Toggle
Autoreload RA
Autoreload RA
Autoreload RB
Autoreload RB
tC
1
PWM: No T1A
Toggle
tC
0
0
0
0
0
1
0
1
0
External Event
Counter
Timer
Underflow
Pos. T1B Edge
Pos. T1B Edge
Pos. T1B Edge
Pos. T1A
Edge
2
External Event
Counter
Timer
Underflow
Pos. T1A
Edge
Captures:
Pos. T1A Edge
or Timer
tC
tC
tC
tC
T1A Pos. Edge
T1B Pos. Edge
Captures:
Underflow
1
0
1
1
1
1
0
1
1
Pos. T1A
Neg. T1B
Edge
T1A Pos. Edge
T1B Neg. Edge
Captures:
Edge or Timer
Underflow
3
Neg. T1A
Neg. T1B
Edge
T1A Neg. Edge
T1B Neg. Edge
Captures:
Edge or Timer
Underflow
Neg. T1A
Neg. T1B
Edge
T1A Neg. Edge
T1B Neg. Edge
Edge or Timer
Underflow
www.national.com
18
This method precludes the use of the crystal clock configura-
tion (since CKO becomes a dedicated output), and so may
only be used with an R/C clock configuration. The third
method of exiting the HALT mode is by pulling the RESET
pin low.
7.0 Power Saving Features
Today, the proliferation of battery-operated based applica-
tions has placed new demands on designers to drive power
consumption down. Battery-operated systems are not the
only type of applications demanding low power. The power
budget constraints are also imposed on those consumer/
industrial applications where well regulated and expensive
power supply costs cannot be tolerated. Such applications
rely on low cost and low power supply voltage derived di-
rectly from the “mains” by using voltage rectifier and passive
components. Low power is demanded even in automotive
applications, due to increased vehicle electronics content.
This is required to ease the burden from the car battery. Low
power 8-bit microcontrollers supply the smarts to control
battery-operated, consumer/industrial, and automotive appli-
cations.
On wakeup from G7 or Port L, the devices resume execution
from the HALT point. On wakeup from RESET execution will
resume from location PC=0 and all RESET conditions apply.
If a crystal or ceramic resonator may be selected as the os-
cillator, the Wakeup signal is not allowed to start the chip
running immediately since crystal oscillators and ceramic
resonators have a delayed start up time to reach full ampli-
tude and frequency stability. The IDLE timer is used to gen-
erate a fixed delay to ensure that the oscillator has indeed
stabilized before allowing instruction execution. In this case,
upon detecting a valid Wakeup signal, only the oscillator cir-
cuitry is enabled. The IDLE timer is loaded with a value of
256 and is clocked with the tC instruction cycle clock. The tC
clock is derived by dividing the oscillator clock down by a fac-
tor of 9. The Schmitt trigger following the CKI inverter on the
chip ensures that the IDLE timer is clocked only when the os-
cillator has a sufficiently large amplitude to meet the Schmitt
trigger specifications. This Schmitt trigger is not part of the
oscillator closed loop. The start-up time-out from the IDLE
timer enables the clock signals to be routed to the rest of the
chip.
Each device offers system designers a variety of low-power
consumption features that enable them to meet the demand-
ing requirements of today’s increasing range of low-power
applications. These features include low voltage operation,
low current drain, and power saving features such as HALT,
IDLE, and Multi-Input wakeup (MIWU).
Each device offers the user two power save modes of opera-
tion: HALT and IDLE. In the HALT mode, all microcontroller
activities are stopped. In the IDLE mode, the on-board oscil-
lator circuitry and timer T0 are active but all other microcon-
troller activities are stopped. In either mode, all on-board
RAM, registers, I/O states, and timers (with the exception of
T0) are unaltered.
If an R/C clock option is being used, the fixed delay is intro-
duced optionally. A control bit, CLKDLY, mapped as configu-
ration bit G7, controls whether the delay is to be introduced
or not. The delay is included if CLKDLY is set, and excluded
if CLKDLY is reset. The CLKDLY bit is cleared on reset.
Clock Monitor if enabled can be active in both modes.
Each device has two options associated with the HALT
mode. The first option enables the HALT mode feature, while
the second option disables the HALT mode selected through
bit 0 of the mask option. With the HALT mode enable option,
the device will enter and exit the HALT mode as described
above. With the HALT disable option, the device cannot be
placed in the HALT mode (writing a “1” to the HALT flag will
have no effect, the HALT flag will remain “0”).
7.1 HALT MODE
Each device can be placed in the HALT mode by writing a “1”
to the HALT flag (G7 data bit). All microcontroller activities,
including the clock and timers, are stopped. The WATCH-
DOG logic on the devices are disabled during the HALT
mode. However, the clock monitor circuitry, if enabled, re-
mains active and will cause the WATCHDOG output pin
(WDOUT) to go low. If the HALT mode is used and the user
does not want to activate the WDOUT pin, the Clock Monitor
should be disabled after the devices come out of reset (re-
setting the Clock Monitor control bit with the first write to the
WDSVR register). In the HALT mode, the power require-
ments of the devices are minimal and the applied voltage
(VCC) may be decreased to Vr (Vr = 2.0V) without altering the
state of the machine.
The WATCHDOG detector circuit is inhibited during the
HALT mode. However, the clock monitor circuit if enabled re-
mains active during HALT mode in order to ensure a clock
monitor error if the device inadvertently enters the HALT
mode as a result of a runaway program or power glitch.
If the device is placed in the HALT mode, with the R/C oscil-
lator selected, the clock input pin (CKI) is forced to a logic
high internally. With the crystal oscillator the CKI pin is
TRI-STATE.
Each device supports three different ways of exiting the
HALT mode. The first method of exiting the HALT mode is
with the Multi-Input Wakeup feature on Port L. The second
method is with a low to high transition on the CKO (G7) pin.
19
www.national.com
7.0 Power Saving Features (Continued)
DS100973-25
FIGURE 15. Wakeup from HALT
7.2 IDLE MODE
The user can enter the IDLE mode with the Timer T0 inter-
rupt enabled. In this case, when the T0PND bit gets set, the
device will first execute the Timer T0 interrupt service routine
and then return to the instruction following the ″Enter Idle
Mode″ instruction.
The device is placed in the IDLE mode by writing a ″1″ to the
IDLE flag (G6 data bit). In this mode, all activity, except the
associated on-board oscillator circuitry, the WATCHDOG
logic, the clock monitor and the IDLE Timer T0, is stopped.
The power supply requirements of the microcontroller in this
mode of operation are typically around 30% of normal power
requirement of the microcontroller.
Alternatively, the user can enter the IDLE mode with the
IDLE Timer T0 interrupt disabled. In this case, the device will
resume normal operation with the instruction immediately
following the ″Enter IDLE Mode″ instruction.
As with the HALT mode, the device can be returned to nor-
mal operation with a reset, or with a Multi-Input Wakeup from
the L Port.
The IDLE timer cannot be started or stopped under software
control, and it is not memory mapped, so it cannot be read or
written by the software. Its state upon Reset is unknown.
Therefore, if the device is put into the IDLE mode at an arbi-
trary time, it will stay in the IDLE mode for somewhere be-
tween 1 and the selected number of instruction cycles. Upon
reset the ITMR register is cleared and selects the 4,096 in-
struction cycle tap of the Idle Timer.
Note: It is necessary to program two NOP instructions following both the set
HALT mode and set IDLE mode instructions. These NOP instructions
are necessary to allow clock resynchronization following the HALT or
IDLE modes.
The microcontroller may also be awakened from the IDLE
mode after a selectable amount of time up to 65,536 instruc-
tion cycles, or 65.536 milliseconds with a 1 MHz instruction
clock frequency (10 MHz oscillator).
The IDLE timer period is selectable from one of five values,
4k, 8k, 16k, 32k or 64k instruction cycles. Selection of this
value is made through the ITMR register.
The user has the option of being interrupted with an under-
flow of the selected bit of the IDLE Timer T0. This condition
is latched into the T0PND pending flag. The interrupt can be
enabled or disabled via the T0EN control bit. Setting the
T0EN flag enables the interrupt and vice versa.
For more information on the IDLE Timer and its associated
interrupt, see the description in the Timers Section.
www.national.com
20
7.0 Power Saving Features (Continued)
DS100973-26
FIGURE 16. Wakeup from IDLE
7.3 MULTI-INPUT WAKEUP
An example may serve to clarify this procedure. Suppose we
wish to change the edge select from positive (low going high)
to negative (high going low) for L Port bit 5, where bit 5 has
previously been enabled for an input interrupt. The program
would be as follows:
The Multi-Input Wakeup feature is used to return (wakeup)
the device from either the HALT or IDLE modes. Alternately
Multi-Input Wakeup/Interrupt feature may also be used to
generate up to 8 edge selectable external interrupts.
RBIT 5, WKEN
SBIT 5, WKEDG ; Change edge polarity
RBIT 5, WKPND ; Reset pending flag
; Disable MIWU
Figure 17 shows the Multi-Input Wakeup logic.
The Multi-Input Wakeup feature utilizes the L Port. The user
selects which particular L port bit (or combination of L Port
bits) will cause the device to exit the HALT or IDLE modes.
The selection is done through the register WKEN. The regis-
ter WKEN is an 8-bit read/write register, which contains a
control bit for every L port bit. Setting a particular WKEN bit
enables a Wakeup from the associated L port pin.
SBIT 5, WKEN
; Enable MIWU
If the L port bits have been used as outputs and then
changed to inputs with Multi-Input Wakeup/Interrupt, a safety
procedure should also be followed to avoid wakeup condi-
tions. After the selected L port bits have been changed from
output to input but before the associated WKEN bits are en-
abled, the associated edge select bits in WKEDG should be
set or reset for the desired edge selects, followed by the as-
sociated WKPND bits being cleared.
The user can select whether the trigger condition on the se-
lected L Port pin is going to be either a positive edge (low to
high transition) or a negative edge (high to low transition).
This selection is made via the register WKEDG, which is an
8-bit control register with a bit assigned to each L Port pin.
Setting the control bit will select the trigger condition to be a
negative edge on that particular L Port pin. Resetting the bit
selects the trigger condition to be a positive edge. Changing
an edge select entails several steps in order to avoid a
Wakeup condition as a result of the edge change. First, the
associated WKEN bit should be reset, followed by the edge
select change in WKEDG. Next, the associated WKPND bit
should be cleared, followed by the associated WKEN bit be-
ing re-enabled.
This same procedure should be used following reset, since
the L port inputs are left floating as a result of reset.
The occurrence of the selected trigger condition for Multi-
Input Wakeup is latched into a pending register called WK-
PND. The respective bits of the WKPND register will be set
on the occurrence of the selected trigger edge on the corre-
sponding Port L pin. The user has the responsibility of clear-
ing these pending flags. Since WKPND is a pending register
for the occurrence of selected wakeup conditions, the device
will not enter the HALT mode if any Wakeup bit is both en-
abled and pending. Consequently, the user must clear the
pending flags before attempting to enter the HALT mode.
WKEN and WKEDG are all read/write registers, and are
cleared at reset. WKPND register contains random value af-
ter reset.
21
www.national.com
7.0 Power Saving Features (Continued)
DS100973-27
FIGURE 17. Multi-Input Wake Up Logic
8.0 Interrupts
8.1 INTRODUCTION
The Software trap has the highest priority while the default
VIS has the lowest priority.
Each device supports eight vectored interrupts. Interrupt
sources include Timer 0, Timer 1, EERAM Write Complete,
Port L Wakeup, Software Trap, MICROWIRE/PLUS, and Ex-
ternal Input.
Each of the 7 maskable inputs has a fixed arbitration ranking
and vector.
Figure 18 shows the Interrupt Block Diagram.
All interrupts force a branch to location 00FF Hex in program
memory. The VIS instruction may be used to vector to the
appropriate service routine from location 00FF Hex.
DS100973-28
FIGURE 18. Interrupt Block Diagram
www.national.com
22
interrupt, and jump to the interrupt handling routine corre-
sponding to the highest priority enabled and active interrupt.
Alternately, the user may choose to poll all interrupt pending
and enable bits to determine the source(s) of the interrupt. If
more than one interrupt is active, the user’s program must
decide which interrupt to service.
8.0 Interrupts (Continued)
8.2 MASKABLE INTERRUPTS
All interrupts other than the Software Trap are maskable.
Each maskable interrupt has an associated enable bit and
pending flag bit. The pending bit is set to 1 when the interrupt
condition occurs. The state of the interrupt enable bit, com-
bined with the GIE bit determines whether an active pending
flag actually triggers an interrupt. All of the maskable inter-
rupt pending and enable bits are contained in mapped con-
trol registers, and thus can be controlled by the software.
Within a specific interrupt service routine, the associated
pending bit should be cleared. This is typically done as early
as possible in the service routine in order to avoid missing
the next occurrence of the same type of interrupt event.
Thus, if the same event occurs a second time, even while the
first occurrence is still being serviced, the second occur-
rence will be serviced immediately upon return from the cur-
rent interrupt routine.
A maskable interrupt condition triggers an interrupt under the
following conditions:
1. The enable bit associated with that interrupt is set.
2. The GIE bit is set.
An interrupt service routine typically ends with an RETI in-
struction. This instruction sets the GIE bit back to 1, pops the
address stored on the stack, and restores that address to the
program counter. Program execution then proceeds with the
next instruction that would have been executed had there
been no interrupt. If there are any valid interrupts pending,
the highest-priority interrupt is serviced immediately upon re-
turn from the previous interrupt.
3. The device is not processing a non-maskable interrupt.
(If
a non-maskable interrupt is being serviced, a
maskable interrupt must wait until that service routine is
completed.)
An interrupt is triggered only when all of these conditions are
met at the beginning of an instruction. If different maskable
interrupts meet these conditions simultaneously, the highest
priority interrupt will be serviced first, and the other pending
interrupts must wait.
8.3 VIS INSTRUCTION
The general interrupt service routine, which starts at address
00FF Hex, must be capable of handling all types of inter-
rupts. The VIS instruction, together with an interrupt vector
table, directs the device to the specific interrupt handling rou-
tine based on the cause of the interrupt.
Upon Reset, all pending bits, individual enable bits, and the
GIE bit are reset to zero. Thus, a maskable interrupt condi-
tion cannot trigger an interrupt until the program enables it by
setting both the GIE bit and the individual enable bit. When
enabling an interrupt, the user should consider whether or
not a previously activated (set) pending bit should be ac-
knowledged. If, at the time an interrupt is enabled, any pre-
vious occurrences of the interrupt should be ignored, the as-
sociated pending bit must be reset to zero prior to enabling
the interrupt. Otherwise, the interrupt may be simply en-
abled; if the pending bit is already set, it will immediately trig-
ger an interrupt. A maskable interrupt is active if its associ-
ated enable and pending bits are set.
VIS is a single-byte instruction, typically used at the very be-
ginning of the general interrupt service routine at address
00FF Hex, or shortly after that point, just after the code used
for context switching. The VIS instruction determines which
enabled and pending interrupt has the highest priority, and
causes an indirect jump to the address corresponding to that
interrupt source. The jump addresses (vectors) for all pos-
sible interrupts sources are stored in a vector table.
The vector table may be as long as 32 bytes (maximum of 16
vectors) and resides at the top of the 256-byte block contain-
ing the VIS instruction. However, if the VIS instruction is at
the very top of a 256-byte block (such as at 00FF Hex), the
vector table resides at the top of the next 256-byte block.
Thus, if the VIS instruction is located somewhere between
00FF and 01DF Hex (the usual case), the vector table is lo-
cated between addresses 01E0 and 01FF Hex. If the VIS in-
struction is located between 01FF and 02DF Hex, then the
vector table is located between addresses 02E0 and 02FF
Hex, and so on.
An interrupt is an asychronous event which may occur be-
fore, during, or after an instruction cycle. Any interrupt which
occurs during the execution of an instruction is not acknowl-
edged until the start of the next normally executed instruction
is to be skipped, the skip is performed before the pending in-
terrupt is acknowledged.
At the start of interrupt acknowledgment, the following ac-
tions occur:
1. The GIE bit is automatically reset to zero, preventing any
subsequent maskable interrupt from interrupting the cur-
rent service routine. This feature prevents one maskable
interrupt from interrupting another one being serviced.
Each vector is 15 bits long and points to the beginning of a
specific interrupt service routine somewhere in the 32 kbyte
memory space. Each vector occupies two bytes of the vector
table, with the higher-order byte at the lower address. The
vectors are arranged in order of interrupt priority. The vector
of the maskable interrupt with the lowest rank is located to
0yE0 (higher-order byte) and 0yE1 (lower-order byte). The
next priority interrupt is located at 0yE2 and 0yE3, and so
forth in increasing rank. The Software Trap has the highest
rank and its vector is always located at 0yFE and 0yFF. The
number of interrupts which can become active defines the
size of the table.
2. The address of the instruction about to be executed is
pushed onto the stack.
3. The program counter (PC) is loaded with 00FF Hex,
causing a jump to that program memory location.
The device requires seven instruction cycles to perform the
actions listed above.
If the user wishes to allow nested interrupts, the interrupts
service routine may set the GIE bit to 1 by writing to the PSW
register, and thus allow other maskable interrupts to interrupt
the current service routine. If nested interrupts are allowed,
caution must be exercised. The user must write the program
in such a way as to prevent stack overflow, loss of saved
context information, and other unwanted conditions.
Table 4 shows the types of interrupts, the interrupt arbitration
ranking, and the locations of the corresponding vectors in
the vector table.
The vector table should be filled by the user with the memory
locations of the specific interrupt service routines. For ex-
The interrupt service routine stored at location 00FF Hex
should use the VIS instruction to determine the cause of the
23
www.national.com
gram context (A, B, X, etc.) and executing the RETI instruc-
tion, an interrupt service routine can be terminated by return-
ing to the VIS instruction. In this case, interrupts will be
serviced in turn until no further interrupts are pending and
the default VIS routine is started. After testing the GIE bit to
ensure that execution is not erroneous, the routine should
restore the program context and execute the RETI to return
to the interrupted program.
8.0 Interrupts (Continued)
ample, if the Software Trap routine is located at 0310 Hex,
then the vector location 0yFE and -0yFF should contain the
data 03 and 10 Hex, respectively. When a Software Trap in-
terrupt occurs and the VIS instruction is executed, the pro-
gram jumps to the address specified in the vector table.
The interrupt sources in the vector table are listed in order of
rank, from highest to lowest priority. If two or more enabled
and pending interrupts are detected at the same time, the
one with the highest priority is serviced first. Upon return
from the interrupt service routine, the next highest-level
pending interrupt is serviced.
This technique can save up to fifty instruction cycles (t
c), or
more, (50µs at 10 MHz oscillator) of latency for pending in-
terrupts with a penalty of fewer than ten instruction cycles if
no further interrupts are pending.
To ensure reliable operation, the user should always use the
VIS instruction to determine the source of an interrupt. Al-
though it is possible to poll the pending bits to detect the
source of an interrupt, this practice is not recommended. The
use of polling allows the standard arbitration ranking to be al-
tered, but the reliability of the interrupt system is compro-
mised. The polling routine must individually test the enable
and pending bits of each maskable interrupt. If a Software
Trap interrupt should occur, it will be serviced last, even
though it should have the highest priority. Under certain con-
ditions, a Software Trap could be triggered but not serviced,
resulting in an inadvertent “locking out” of all maskable inter-
rupts by the Software Trap pending flag. Problems such as
this can be avoided by using VIS instruction.
If the VIS instruction is executed, but no interrupts are en-
abled and pending, the lowest-priority interrupt vector is
used, and a jump is made to the corresponding address in
the vector table. This is an unusual occurrence, and may be
the result of an error. It can legitimately result from a change
in the enable bits or pending flags prior to the execution of
the VIS instruction, such as executing a single cycle instruc-
tion which clears an enable flag at the same time that the
pending flag is set. It can also result, however, from inadvert-
ent execution of the VIS command outside of the context of
an interrupt.
The default VIS interrupt vector can be useful for applica-
tions in which time critical interrupts can occur during the
servicing of another interrupt. Rather than restoring the pro-
TABLE 4. Interrupt Vector Table
Description
Arbitration
Ranking
Vector Address (Note 26)
Source
(Hi-Low Byte)
0yFE–0yFF
(1) Highest
Software
INTR Instruction
(2)
Reserved
External
0yFC–0yFD
0yFA–0yFB
0yF8–0yF9
0yF6–0yF7
0yF4–0yF5
0yF2–0yF3
0yF0–0yF1
0yEE–0yEF
0yEC–0yED
0yEA–0yEB
0yE8–0yE9
0yE6–0yE7
0yE4–0yE5
0yE2–0yE3
0yE0–0yE1
(3)
G0
(4)
Timer T0
Underflow
(5)
Timer T1
T1A/Underflow
T1B
(6)
Timer T1
(7)
MICROWIRE/PLUS
EERAM
BUSY Low
EERAM Write Complete
(8)
(9)
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Port L/Wakeup
Default VIS
(10)
(11)
(12)
(13)
(14)
(15)
(16) Lowest
Port L Edge
Reserved
Note 26: y is a variable which represents the VIS block. VIS and the vector table must be located in the same 256-byte block except if VIS is located at the last ad-
dress of a block. In this case, the table must be in the next block.
www.national.com
24
mains unchanged. The new PC is therefore pointing to the
vector of the active interrupt with the highest arbitration rank-
ing. This vector is read from program memory and placed
into the PC which is now pointed to the 1st instruction of the
service routine of the active interrupt with the highest arbitra-
tion ranking.
8.0 Interrupts (Continued)
8.3.1 VIS Execution
When the VIS instruction is executed it activates the arbitra-
tion logic. The arbitration logic generates an even number
between E0 and FE (E0, E2, E4, E6 etc...) depending on
which active interrupt has the highest arbitration ranking at
the time of the 1st cycle of VIS is executed. For example, if
the software trap interrupt is active, FE is generated. If the
external interrupt is active and the software trap interrupt is
not, then FA is generated and so forth. If the only active inter-
rupt is software trap, than E0 is generated. This number re-
places the lower byte of the PC. The upper byte of the PC re-
Figure 19 illustrates the different steps performed by the VIS
instruction. Figure 20 shows a flowchart for the VIS instruc-
tion.
The non-maskable interrupt pending flag is cleared by the
RPND (Reset Non-Maskable Pending Bit) instruction (under
certain conditions) and upon RESET.
DS100973-29
FIGURE 19. VIS Operation
25
www.national.com
8.0 Interrupts (Continued)
DS100973-30
FIGURE 20. VIS Flowchart
www.national.com
26
8.0 Interrupts (Continued)
Programming Example: External Interrupt
PSW
CNTRL
RBIT
RBIT
SBIT
SBIT
SBIT
JP
=00EF
=00EE
0,PORTGC
0,PORTGD
IEDG, CNTRL
EXEN, PSW
GIE, PSW
WAIT
; G0 pin configured Hi-Z
; Ext interrupt polarity; falling edge
; Enable the external interrupt
; Set the GIE bit
WAIT:
; Wait for external interrupt
.
.
.
.=0FF
VIS
; The interrupt causes a
; branch to address 0FF
; The VIS causes a branch to
;interrupt vector table
.
.
.
.=01FA
.ADDRW SERVICE
; Vector table (within 256 byte
; of VIS inst.) containing the ext
; interrupt service routine
.
.
INT_EXIT:
SERVICE:
RETI
.
.
RBIT
EXPND, PSW
; Interrupt Service Routine
; Reset ext interrupt pend. bit
.
.
.
JP
INT_EXIT
; Return, set the GIE bit
27
www.national.com
flag; upon return to the first Software Trap routine, the
STPND flag will have the wrong state. This will allow
maskable interrupts to be acknowledged during the servicing
of the first Software Trap. To avoid problems such as this, the
user program should contain the Software Trap routine to
perform a recovery procedure rather than a return to normal
execution.
8.0 Interrupts (Continued)
8.4 NON-MASKABLE INTERRUPT
8.4.1 Pending Flag
There is a pending flag bit associated with the non-maskable
interrupt, called STPND. This pending flag is not memory-
mapped and cannot be accessed directly by the software.
Under normal conditions, the STPND flag is reset by a
RPND instruction in the Software Trap service routine. If a
programming error or hardware condition (brownout, power
supply glitch, etc.) sets the STPND flag without providing a
way for it to be cleared, all other interrupts will be locked out.
To alleviate this condition, the user can use extra RPND in-
structions in the main program and in the WATCHDOG ser-
vice routine (if present). There is no harm in executing extra
RPND instructions in these parts of the program.
The pending flag is reset to zero when a device Reset oc-
curs. When the non-maskable interrupt occurs, the associ-
ated pending bit is set to 1. The interrupt service routine
should contain an RPND instruction to reset the pending flag
to zero. The RPND instruction always resets the STPND
flag.
8.4.2 Software Trap
The Software Trap is a special kind of non-maskable inter-
rupt which occurs when the INTR instruction (used to ac-
knowledge interrupts) is fetched from program memory and
placed in the instruction register. This can happen in a vari-
ety of ways, usually because of an error condition. Some ex-
amples of causes are listed below.
8.5 PORT L INTERRUPTS
Port L provides the user with an additional eight fully select-
able, edge sensitive interrupts which are all vectored into the
same service subroutine.
The interrupt from Port L shares logic with the wake up cir-
cuitry. The register WKEN allows interrupts from Port L to be
individually enabled or disabled. The register WKEDG speci-
fies the trigger condition to be either a positive or a negative
edge. Finally, the register WKPND latches in the pending
trigger conditions.
If the program counter incorrectly points to a memory loca-
tion beyond the available program memory space, the non-
existent or unused memory location returns zeroes which is
interpreted as the INTR instruction.
If the stack is popped beyond the allowed limit (address 06F
Hex), a 7FFF will be loaded into the PC, if this last location in
program memory is unprogrammed or unavailable, a Soft-
ware Trap will be triggered.
The GIE (Global Interrupt Enable) bit enables the interrupt
function.
A control flag, LPEN, functions as a global interrupt enable
for Port L interrupts. Setting the LPEN flag will enable inter-
rupts and vice versa. A separate global pending flag is not
needed since the register WKPND is adequate.
A Software Trap can be triggered by a temporary hardware
condition such as a brownout or power supply glitch.
The Software Trap has the highest priority of all interrupts.
When a Software Trap occurs, the STPND bit is set. The GIE
bit is not affected and the pending bit (not accessible by the
user) is used to inhibit other interrupts and to direct the pro-
gram to the ST service routine with the VIS instruction. Noth-
ing can interrupt a Software Trap service routine except for
another Software Trap. The STPND can be reset only by the
RPND instruction or a chip Reset.
Since Port L is also used for waking the device out of the
HALT or IDLE modes, the user can elect to exit the HALT or
IDLE modes either with or without the interrupt enabled. If he
elects to disable the interrupt, then the device will restart ex-
ecution from the instruction immediately following the in-
struction that placed the microcontroller in the HALT or IDLE
modes. In the other case, the device will first execute the in-
terrupt service routine and then revert to normal operation.
(See HALT MODE for clock option wakeup information.)
The Software Trap indicates an unusual or unknown error
condition. Generally, returning to normal execution at the
point where the Software Trap occurred cannot be done re-
liably. Therefore, the Software Trap service routine should
reinitialize the stack pointer and perform a recovery proce-
dure that restarts the software at some known point, similar
to a device Reset, but not necessarily performing all the
same functions as a device Reset. The routine must also ex-
ecute the RPND instruction to reset the STPND flag. Other-
wise, all other interrupts will be locked out. To the extent pos-
sible, the interrupt routine should record or indicate the
context of the device so that the cause of the Software Trap
can be determined.
8.6 INTERRUPT SUMMARY
The device uses the following types of interrupts, listed be-
low in order of priority:
1. The Software Trap non-maskable interrupt, triggered by
the INTR (00 opcode) instruction. The Software Trap is
acknowledged immediately. This interrupt service rou-
tine can be interrupted only by another Software Trap.
The Software Trap should end with two RPND instruc-
tions followed by a restart procedure.
2. Maskable interrupts, triggered by an on-chip peripheral
block or an external device connected to the device. Un-
der ordinary conditions, a maskable interrupt will not in-
If the user wishes to return to normal execution from the
point at which the Software Trap was triggered, the user
must first execute RPND, followed by RETSK rather than
RETI or RET. This is because the return address stored on
the stack is the address of the INTR instruction that triggered
the interrupt. The program must skip that instruction in order
to proceed with the next one. Otherwise, an infinite loop of
Software Traps and returns will occur.
terrupt any other interrupt routine in progress.
maskable interrupt routine in progress can be inter-
rupted by the non-maskable interrupt request.
maskable interrupt routine should end with an RETI in-
struction or, prior to restoring context, should return to
execute the VIS instruction. This is particularly useful
when exiting long interrupt service routiness if the time
between interrupts is short. In this case the RETI instruc-
tion would only be executed when the default VIS rou-
tine is reached.
A
A
Programming a return to normal execution requires careful
consideration. If the Software Trap routine is interrupted by
another Software Trap, the RPND instruction in the service
routine for the second Software Trap will reset the STPND
www.national.com
28
9.1 CLOCK MONITOR
9.0 WATCHDOG/Clock Monitor
The Clock Monitor aboard the device can be selected or de-
selected under program control. The Clock Monitor is guar-
anteed not to reject the clock if the instruction cycle clock (1/
tC) is greater or equal to 10 kHz. This equates to a clock
input rate on CKI of greater or equal to 100 kHz.
Each device contains a user selectable WATCHDOG and
clock monitor. The following section is applicable only if
WATCHDOG feature has been selected by mask option. The
WATCHDOG is designed to detect the user program getting
stuck in infinite loops resulting in loss of program control or
“runaway” programs.
9.2 WATCHDOG/CLOCK MONITOR OPERATION
The WATCHDOG logic contains two separate service win-
dows. While the user programmable upper window selects
the WATCHDOG service time, the lower window provides
protection against an infinite program loop that contains the
WATCHDOG service instruction.
The WATCHDOG and Clock Monitor are disabled during re-
set. The device comes out of reset with the WATCHDOG
armed, the WATCHDOG Window Select bits (bits 6, 7 of the
WDSVR Register) set, and the Clock Monitor bit (bit 0 of the
WDSVR Register) enabled. Thus, a Clock Monitor error will
occur after coming out of reset, if the instruction cycle clock
frequency has not reached a minimum specified value, in-
cluding the case where the oscillator fails to start.
The Clock Monitor is used to detect the absence of a clock or
a very slow clock below a specified rate on the CKI pin.
The WATCHDOG consists of two independent logic blocks:
WD UPPER and WD LOWER. WD UPPER establishes the
upper limit on the service window and WD LOWER defines
the lower limit of the service window.
The WDSVR register can be written to only once after reset
and the key data (bits 5 through 1 of the WDSVR Register)
must match to be a valid write. This write to the WDSVR reg-
ister involves two irrevocable choices: (i) the selection of the
WATCHDOG service window (ii) enabling or disabling of the
Clock Monitor. Hence, the first write to WDSVR Register in-
volves selecting or deselecting the Clock Monitor, select the
WATCHDOG service window and match the WATCHDOG
key data. Subsequent writes to the WDSVR register will
compare the value being written by the user to the WATCH-
DOG service window value and the key data (bits 7 through
1) in the WDSVR Register. Table 7 shows the sequence of
events that can occur.
Servicing the WATCHDOG consists of writing a specific
value to a WATCHDOG Service Register named WDSVR
which is memory mapped in the RAM. This value is com-
posed of three fields, consisting of a 2-bit Window Select, a
5-bit Key Data field, and the 1-bit Clock Monitor Select field.
Table 5 shows the WDSVR register.
TABLE 5. WATCHDOG Service Register (WDSVR)
Window
Select
Clock
Key Data
The user must service the WATCHDOG at least once before
the upper limit of the service window expires. The WATCH-
DOG may not be serviced more than once in every lower
limit of the service window.
Monitor
X
7
X
6
0
5
1
4
1
3
0
2
0
1
Y
0
The lower limit of the service window is fixed at 256 instruc-
tion cycles. Bits 7 and 6 of the WDSVR register allow the
user to pick an upper limit of the service window.
The WATCHDOG has an output pin associated with it. This
is the WDOUT pin, on pin 1 of the port G. WDOUT is active
low and must be externally connected to the RESET pin or to
some other external logic which handles WATCHDOG event.
The WDOUT pin has a weak pullup in the inactive state. This
pull-up is sufficient to serve as the connection to VCC for sys-
tems which use the internal Power On Reset. Upon trigger-
ing the WATCHDOG, the logic will pull the WDOUT (G1) pin
low for an additional 16 tC–32 tC cycles after the signal level
on WDOUT pin goes below the lower Schmitt trigger thresh-
old. After this delay, the WDOUT output will go high. The
WATCHDOG service window will restart when the WDOUT
pin goes high.
Table 6 shows the four possible combinations of lower and
upper limits for the WATCHDOG service window. This flex-
ibility in choosing the WATCHDOG service window prevents
any undue burden on the user software.
Bits 5, 4, 3, 2 and 1 of the WDSVR register represent the
5-bit Key Data field. The key data is fixed at 01100. Bit 0 of
the WDSVR Register is the Clock Monitor Select bit.
TABLE 6. WATCHDOG Service Window Select
WDSVR WDSVR
Clock
Service Window
(Lower-Upper Limits)
2048–8k tC Cycles
A WATCHDOG service while the WDOUT signal is active will
be ignored. The state of the WDOUT pin is not guaranteed
on reset, but if it powers up low then the WATCHDOG will
time out and WDOUT will go high.
Bit 7
Bit 6
Monitor
0
0
1
1
x
x
0
1
0
1
x
x
x
x
x
x
0
1
2048–16k tC Cycles
2048–32k tC Cycles
2048–64k tC Cycles
Clock Monitor Disabled
Clock Monitor Enabled
The Clock Monitor forces the G1 pin low upon detecting a
clock frequency error. The Clock Monitor error will continue
until the clock frequency has reached the minimum specified
value, after which the G1 output will go high following 16
tC–32 tC clock cycles. The Clock Monitor generates a con-
tinual Clock Monitor error if the oscillator fails to start, or fails
to reach the minimum specified frequency. The specification
for the Clock Monitor is as follows:
>
1/tC 10 kHz—No clock rejection.
<
1/tC 10 Hz—Guaranteed clock rejection.
29
www.national.com
9.0 WATCHDOG/Clock Monitor (Continued)
TABLE 7. WATCHDOG Service Actions
Key
Window Clock
Action
Data
Data
Monitor
Match
Match
Match
Valid Service: Restart Service Window
Error: Generate WATCHDOG Output
Error: Generate WATCHDOG Output
Error: Generate WATCHDOG Output
Don’t Care
Mismatch
Don’t Care
Mismatch
Don’t Care
Don’t Care
Don’t Care
Don’t Care
Mismatch
9.3 WATCHDOG AND CLOCK MONITOR SUMMARY
•
A hardware WATCHDOG service occurs just as the de-
vice exits the IDLE mode. Consequently, the WATCH-
DOG should not be serviced for at least 2048 instruction
cycles following IDLE, but must be serviced within the se-
lected window to avoid a WATCHDOG error.
The following salient points regarding the WATCHDOG and
CLOCK MONITOR should be noted:
•
Both the WATCHDOG and CLOCK MONITOR detector
circuits are inhibited during RESET.
•
Following RESET, the initial WATCHDOG service (where
the service window and the CLOCK MONITOR enable/
disable must be selected) may be programmed any-
where within the maximum service window (65,536 in-
struction cycles) initialized by RESET. Note that this initial
WATCHDOG service may be programmed within the ini-
tial 2048 instruction cycles without causing a WATCH-
DOG error.
•
Following RESET, the WATCHDOG and CLOCK MONI-
TOR are both enabled, with the WATCHDOG having the
maximum service window selected.
•
•
•
•
The WATCHDOG service window and CLOCK MONI-
TOR enable/disable option can only be changed once,
during the initial WATCHDOG service following RESET.
The initial WATCHDOG service must match the key data
value in the WATCHDOG Service register WDSVR in or-
der to avoid a WATCHDOG error.
9.4 DETECTION OF ILLEGAL CONDITIONS
Subsequent WATCHDOG services must match all three
data fields in WDSVR in order to avoid WATCHDOG er-
rors.
The device can detect various illegal conditions resulting
from coding errors, transient noise, power supply voltage
drops, runaway programs, etc.
The correct key data value cannot be read from the
WATCHDOG Service register WDSVR. Any attempt to
read this key data value of 01100 from WDSVR will read
as key data value of all 0’s.
Reading of undefined ROM gets zeroes. The opcode for
software interrupt is 00. If the program fetches instructions
from undefined ROM, this will force a software interrupt, thus
signaling that an illegal condition has occurred.
•
•
The WATCHDOG detector circuit is inhibited during both
the HALT and IDLE modes.
The subroutine stack grows down for each call (jump to sub-
routine), interrupt, or PUSH, and grows up for each return or
POP. The stack pointer is initialized to RAM location 06F Hex
during reset. Consequently, if there are more returns than
calls, the stack pointer will point to addresses 070 and 071
Hex (which are undefined RAM). Undefined RAM from ad-
dresses 070 to 07F (Segment 0), and all other segments
(i.e., Segments 4 … etc.) is read as all 1’s, which in turn will
cause the program to return to address 7FFF Hex. It is rec-
ommended that the user either leave this location unpro-
grammed or place an INTR instruction (all 0’s) in this location
to generate a software interrupt signaling an illegal condition.
The CLOCK MONITOR detector circuit is active during
both the HALT and IDLE modes. Consequently, the de-
vice inadvertently entering the HALT mode will be de-
tected as a CLOCK MONITOR error (provided that the
CLOCK MONITOR enable option has been selected by
the program).
•
•
With the single-pin R/C oscillator option selected and the
CLKDLY bit reset, the WATCHDOG service window will
resume following HALT mode from where it left off before
entering the HALT mode.
Thus, the chip can detect the following illegal conditions:
1. Executing from undefined ROM.
With the crystal oscillator option selected, or with the
single-pin R/C oscillator option selected and the CLKDLY
bit set, the WATCHDOG service window will be set to its
selected value from WDSVR following HALT. Conse-
quently, the WATCHDOG should not be serviced for at
least 2048 instruction cycles following HALT, but must be
serviced within the selected window to avoid a WATCH-
DOG error.
2. Over “POP”ing the stack by having more returns than
calls.
When the software interrupt occurs, the user can re-initialize
the stack pointer and do a recovery procedure before restart-
ing (this recovery program is probably similar to that follow-
ing reset, but might not contain the same program initializa-
tion procedures). The recovery program should reset the
software interrupt pending bit using the RPND instruction.
•
•
The IDLE timer T0 is not initialized with external RESET.
The user can sync in to the IDLE counter cycle with an
IDLE counter (T0) interrupt or by monitoring the T0PND
flag. The T0PND flag is set whenever the selected bit of
the IDLE counter toggles (every 4, 8, 16, 32 or 64k in-
struction cycles). The user is responsible for resetting the
T0PND flag.
www.national.com
30
10.1 MICROWIRE/PLUS OPERATION
10.0 MICROWIRE/PLUS
Setting the BUSY bit in the PSW register causes the
MICROWIRE/PLUS to start shifting the data. It gets reset
when eight data bits have been shifted. The user may reset
the BUSY bit by software to allow less than 8 bits to shift. If
enabled, an interrupt is generated when eight data bits have
been shifted. The device may enter the MICROWIRE/PLUS
mode either as a Master or as a Slave. Figure 21 shows how
two microcontroller devices and several peripherals may be
interconnected using the MICROWIRE/PLUS arrangements.
MICROWIRE/PLUS is a serial SPI compatible synchronous
communications interface. The MICROWIRE/PLUS capabil-
ity enables the device to interface with MICROWIRE/PLUS
or SPI peripherals (i.e. A/D converters, display drivers, EE-
PROMs etc.) and with other microcontrollers which support
the MICROWIRE/PLUS or SPI interface. It consists of an
8-bit serial shift register (SIO) with serial data input (SI), se-
rial data output (SO) and serial shift clock (SK). Figure 21
shows a block diagram of the MICROWIRE/PLUS logic.
WARNING
The shift clock can be selected from either an internal source
or an external source. Operating the MICROWIRE/PLUS ar-
rangement with the internal clock source is called the Master
mode of operation. Similarly, operating the MICROWIRE/
PLUS arrangement with an external shift clock is called the
Slave mode of operation.
The SIO register should only be loaded when the SK clock is
in the idle phase. Loading the SIO register while the SK clock
is in the active phase, will result in undefined data in the SIO
register.
Setting the BUSY flag when the input SK clock is in the ac-
tive phase while in the MICROWIRE/PLUS is in the slave
mode may cause the current SK clock for the SIO shift reg-
ister to be narrow. For safety, the BUSY flag should only be
set when the input SK clock is in the idle phase.
The CNTRL register is used to configure and control the
MICROWIRE/PLUS mode. To use the MICROWIRE/PLUS,
the MSEL bit in the CNTRL register is set to one. In the mas-
ter mode, the SK clock rate is selected by the two bits, SL0
and SL1, in the CNTRL register. Table 8 details the different
clock rates that may be selected.
10.1.1 MICROWIRE/PLUS Master Mode Operation
In the MICROWIRE/PLUS Master mode of operation the
shift clock (SK) is generated internally. The MICROWIRE
Master always initiates all data exchanges. The MSEL bit in
the CNTRL register must be set to enable the SO and SK
functions onto the G Port. The SO and SK pins must also be
selected as outputs by setting appropriate bits in the Port G
configuration register. In the slave mode, the shift clock
stops after 8 clock pulses. Table 9 summarizes the bit set-
tings required for Master mode of operation.
TABLE 8. MICROWIRE/PLUS
Master Mode Clock Select
SL1
0
SL0
SK Period
2 x tC
0
1
x
0
4 x tC
1
8 x tC
Where t is the instruction cycle clock
C
DS100973-32
FIGURE 21. MICROWIRE/PLUS Application
31
www.national.com
The user must set the BUSY flag immediately upon entering
the Slave mode. This ensures that all data bits sent by the
Master is shifted properly. After eight clock pulses the BUSY
flag is clear, the shift clock is stopped, and the sequence
may be repeated.
10.0 MICROWIRE/PLUS (Continued)
10.1.2 MICROWIRE/PLUS Slave Mode Operation
In the MICROWIRE/PLUS Slave mode of operation the SK
clock is generated by an external source. Setting the MSEL
bit in the CNTRL register enables the SO and SK functions
onto the G Port. The SK pin must be selected as an input
and the SO pin is selected as an output pin by setting and re-
setting the appropriate bits in the Port G configuration regis-
ter. Table 9 summarizes the settings required to enter the
Slave mode of operation.
10.1.3 Alternate SK Phase Operation and SK Idle
Polarity
The device allows either the normal SK clock or an alternate
phase SK clock to shift data in and out of the SIO register. In
both the modes the SK idle polarity can be either high or low.
The polarity is selected by bit 5 of Port G data register. In the
normal mode data is shifted in on the rising edge of the SK
clock and the data is shifted out on the falling edge of the SK
clock. In the alternate SK phase operation, data is shifted in
on the falling edge of the SK clock and shifted out on the ris-
ing edge of the SK clock. Bit 6 of Port G configuration regis-
ter selects the SK edge.
TABLE 9. MICROWIRE/PLUS Mode Settings
This table assumes that the control flag MSEL is set.
G4 (SO)
Config. Bit
1
G5 (SK)
Config. Bit
1
G4
Fun.
SO
G5
Fun.
Int.
Operation
MICROWIRE/PLUS
Master
A control flag, SKSEL, allows either the normal SK clock or
the alternate SK clock to be selected. Resetting SKSEL
causes the MICROWIRE/PLUS logic to be clocked from the
normal SK signal. Setting the SKSEL flag selects the alter-
nate SK clock. The SKSEL is mapped into the G6 configura-
tion bit. The SKSEL flag will power up in the reset condition,
selecting the normal SK signal.
SK
0
1
0
1
0
0
TRI-
STATE
SO
Int.
MICROWIRE/PLUS
Master
SK
Ext.
SK
MICROWIRE/PLUS
Slave
TRI-
Ext.
SK
MICROWIRE/PLUS
Slave
STATE
TABLE 10. MICROWIRE/PLUS Shift Clock Polarity and Sample/Shift Phase
Port G
SK Phase
G6 (SKSEL)
G5 Data
SO Clocked Out
On:
SI Sampled On:
SK Idle
Phase
Low
Config. Bit
Bit
0
Normal
Alternate
Alternate
Normal
0
1
0
1
SK Falling Edge
SK Rising Edge
SK Rising Edge
SK Falling Edge
SK Rising Edge
SK Falling Edge
SK Falling Edge
SK Rising Edge
0
Low
1
High
1
High
DS100973-33
FIGURE 22. MICROWIRE/PLUS SPI Mode Interface Timing, Normal SK Mode, SK Idle Phase being Low
DS100973-34
FIGURE 23. MICROWIRE/PLUS SPI Mode Interface Timing, Alternate SK Mode, SK Idle Phase being Low
www.national.com
32
10.0 MICROWIRE/PLUS (Continued)
DS100973-35
FIGURE 24. MICROWIRE/PLUS SPI Mode Interface Timing, Alternate SK Mode, SK Idle Phase being High
DS100973-31
FIGURE 25. MICROWIRE/PLUS SPI Mode Interface Timing, Normal SK Mode, SK Idle Phase being High
33
www.national.com
11.0 Memory Map
All RAM, ports and registers (except A and PC) are mapped into data memory address space.
Address
S/ADD REG
0000 to 006F
0070 to 007F
Contents
On-Chip RAM bytes (112 bytes)
Unused RAM Address Space (Reads
As All Ones)
xx80 to xxBF
xxC7
Unused RAM Address Space (Reads
Undefined Data)
WATCHDOG Service Register
(Reg:WDSVR)
xxC8
MIWU Edge Select Register
(Reg:WKEDG)
xxC9
xxCA
MIWU Enable Register (Reg:WKEN)
MIWU Pending Register
(Reg:WKPND)
xxCB
Reserved
xxCC
Reserved
xxCD to xxCE
xxCF
Reserved
Idle Timer Window Length (Reg:ITMR)
Port L Data Register
Port L Configuration Register
Port L Input Pins (Read Only)
Reserved
xxD0
xxD1
xxD2
xxD3
xxD4
Port G Data Register
Port G Configuration Register
Port G Input Pins (Read Only)
Reserved
xxD5
xxD6
xxD7 to xxDF
xxE0
EERAM Control Register E2CFG
Reserved for EE Control Registers
xxE1 to xxE5
xxE6
Timer T1 Autoload Register T1RB
Lower Byte
xxE7
Timer T1 Autoload Register T1RB
Upper Byte
xxE8
xxE9
xxEA
xxEB
xxEC
ICNTRL Register
MICROWIRE/PLUS Shift Register
Timer T1 Lower Byte
Timer T1 Upper Byte
Timer T1 Autoload Register T1RA
Lower Byte
xxED
Timer T1 Autoload Register T1RA
Upper Byte
xxEE
CNTRL Control Register
PSW Register
xxEF
xxF0 to xxFB
xxFC
On-Chip RAM Mapped as Registers
X Register
xxFD
SP Register
xxFE
B Register
xxFF
S Register
0100–017F
On-Chip 128 EERAM Bytes
Note: Reading memory locations 0070H–007FH (Segment 0) will return all
ones. Reading unused memory locations 0080H–00BFH (Segment 0)
will return undefined data. Reading memory locations from other Seg-
ments (i.e., Segment 2, Segment 3, … etc.) will return undefined data.
www.national.com
34
The available addressing modes are:
12.0 Instruction Set
•
•
•
Direct
12.1 INTRODUCTION
Register B or X Indirect
This section defines the instruction set of the COPSAx7
Family members. It contains information about the instruc-
tion set features, addressing modes and types.
Register
B or X Indirect with Post-Incrementing/
Decrementing
•
•
•
Immediate
Immediate Short
Indirect from Program Memory
12.2 INSTRUCTION FEATURES
The strength of the instruction set is based on the following
features:
The addressing modes are described below. Each descrip-
tion includes an example of an assembly language instruc-
tion using the described addressing mode.
•
•
•
•
•
•
Mostly single-byte opcode instructions minimize program
size.
Direct. The memory address is specified directly as a byte in
the instruction. In assembly language, the direct address is
written as a numerical value (or a label that has been defined
elsewhere in the program as a numerical value).
One instruction cycle for the majority of single-byte in-
structions to minimize program execution time.
Many single-byte, multiple function instructions such as
DRSZ.
Example: Load Accumulator Memory Direct
LD A,05
Three memory mapped pointers: two for register indirect
addressing, and one for the software stack.
Reg/Data
Memory
Contents
Before
Contents
After
Sixteen memory mapped registers that allow an opti-
mized implementation of certain instructions.
Ability to set, reset, and test any individual bit in data
memory address space, including the memory-mapped
I/O ports and registers.
Accumulator
Memory Location
0005 Hex
XX Hex
A6 Hex
A6 Hex
A6 Hex
•
•
Register-Indirect LOAD and EXCHANGE instructions
with optional automatic post-incrementing or decrement-
ing of the register pointer. This allows for greater effi-
ciency (both in cycle time and program code) in loading,
walking across and processing fields in data memory.
Register B or X Indirect. The memory address is specified
by the contents of the B Register or X register (pointer regis-
ter). In assembly language, the notation [B] or [X] specifies
which register serves as the pointer.
Example: Exchange Memory with Accumulator, B Indirect
X A,[B]
Unique instructions to optimize program size and
throughput efficiency. Some of these instructions are
DRSZ, IFBNE, DCOR, RETSK, VIS and RRC.
Reg/Data
Memory
Contents
Before
Contents
After
12.3 ADDRESSING MODES
The instruction set offers a variety of methods for specifying
memory addresses. Each method is called an addressing
mode. These modes are classified into two categories: oper-
and addressing modes and transfer-of-control addressing
modes. Operand addressing modes are the various meth-
ods of specifying an address for accessing (reading or writ-
ing) data. Transfer-of-control addressing modes are used in
conjunction with jump instructions to control the execution
sequence of the software program.
Accumulator
Memory Location
0005 Hex
01 Hex
87 Hex
87 Hex
01 Hex
B Pointer
05 Hex
05 Hex
Register
B or X Indirect with Post-Incrementing/
Decrementing. The relevant memory address is specified
by the contents of the B Register or X register (pointer regis-
ter). The pointer register is automatically incremented or
decremented after execution, allowing easy manipulation of
memory blocks with software loops. In assembly language,
the notation [B+], [B−], [X+], or [X−] specifies which register
serves as the pointer, and whether the pointer is to be incre-
mented or decremented.
12.3.1 Operand Addressing Modes
The operand of an instruction specifies what memory loca-
tion is to be affected by that instruction. Several different op-
erand addressing modes are available, allowing memory lo-
cations to be specified in a variety of ways. An instruction
can specify an address directly by supplying the specific ad-
dress, or indirectly by specifying a register pointer. The con-
tents of the register (or in some cases, two registers) point to
the desired memory location. In the immediate mode, the
data byte to be used is contained in the instruction itself.
Example: Exchange Memory with Accumulator, B Indirect
with Post-Increment
X A,[B+]
Reg/Data
Memory
Contents
Before
Contents
After
Each addressing mode has its own advantages and disad-
vantages with respect to flexibility, execution speed, and pro-
gram compactness. Not all modes are available with all in-
structions. The Load (LD) instruction offers the largest
number of addressing modes.
Accumulator
Memory Location
0005 Hex
03 Hex
62 Hex
62 Hex
03 Hex
B Pointer
05 Hex
06 Hex
Intermediate. The data for the operation follows the instruc-
tion opcode in program memory. In assembly language, the
number sign character (#) indicates an immediate operand.
35
www.national.com
The transfer-of-control addressing modes are described be-
low. Each description includes an example of a Jump in-
struction using a particular addressing mode, and the effect
on the Program Counter bytes of executing that instruction.
12.0 Instruction Set (Continued)
Example: Load Accumulator Immediate
#
LD A, 05
Jump Relative. In this 1-byte instruction, six bits of the in-
struction opcode specify the distance of the jump from the
current program memory location. The distance of the jump
can range from −31 to +32. A JP+1 instruction is not allowed.
The programmer should use a NOP instead.
Reg/Data
Contents
Before
Contents
After
Memory
Accumulator
XX Hex
05 Hex
Immediate Short. This is a special case of an immediate in-
struction. In the “Load B immediate” instruction, the 4-bit im-
mediate value in the instruction is loaded into the lower
nibble of the B register. The upper nibble of the B register is
reset to 0000 binary.
Example: Jump Relative
JP 0A
Reg
Contents
Before
Contents
After
Example: Load B Register Immediate Short
LD B,#7
PCU
PCL
02 Hex
05 Hex
02 Hex
0F Hex
Reg/Data
Memory
B Pointer
Contents
Before
Contents
After
Jump Absolute. In this 2-byte instruction, 12 bits of the in-
struction opcode specify the new contents of the Program
Counter. The upper three bits of the Program Counter re-
main unchanged, restricting the new Program Counter ad-
dress to the same 4 kbyte address space as the current in-
struction.
12 Hex
07 Hex
Indirect from Program Memory. This is a special case of
an indirect instruction that allows access to data tables
stored in program memory. In the “Load Accumulator Indi-
rect” (LAID) instruction, the upper and lower bytes of the Pro-
gram Counter (PCU and PCL) are used temporarily as a
pointer to program memory. For purposes of accessing pro-
gram memory, the contents of the Accumulator and PCL are
exchanged. The data pointed to by the Program Counter is
loaded into the Accumulator, and simultaneously, the original
contents of PCL are restored so that the program can re-
sume normal execution.
(This restriction is relevant only in devices using more than
one 4 kbyte program memory space.)
Example: Jump Absolute
JMP 0125
Reg
Contents
Before
Contents
After
PCU
PCL
0C Hex
77 Hex
01 Hex
25 Hex
Example: Load Accumulator Indirect
LAID
Jump Absolute Long. In this 3-byte instruction, 15 bits of
the instruction opcode specify the new contents of the Pro-
gram Counter.
Reg/Data
Memory
Contents
Before
04 Hex
35 Hex
1F Hex
25 Hex
Contents
After
Example: Jump Absolute Long
JMP 03625
PCU
04 Hex
36 Hex
25 Hex
25 Hex
PCL
Accumulator
Memory Location
041F Hex
Reg/
Memory
PCU
Contents
Before
Contents
After
42 Hex
36 Hex
36 Hex
25 Hex
PCL
12.3.2 Tranfer-of-Control Addressing Modes
Program instructions are usually executed in sequential or-
der. However, Jump instructions can be used to change the
normal execution sequence. Several transfer-of-control ad-
dressing modes are available to specify jump addresses.
A change in program flow requires a non-incremental
change in the Program Counter contents. The Program
Counter consists of two bytes, designated the upper byte
(PCU) and lower byte (PCL). The most significant bit of PCU
is not used, leaving 15 bits to address the program memory.
Different addressing modes are used to specify the new ad-
dress for the Program Counter. The choice of addressing
mode depends primarily on the distance of the jump. Farther
jumps sometimes require more instruction bytes in order to
completely specify the new Program Counter contents.
The available transfer-of-control addressing modes are:
•
•
•
•
Jump Relative
Jump Absolute
Jump Absolute Long
Jump Indirect
www.national.com
36
Jump to Subroutine Long (JSRL)
Return from Subroutine (RET)
Return from Subroutine and Skip (RETSK)
Return from Interrupt (RETI)
12.0 Instruction Set (Continued)
Jump Indirect. In this 1-byte instruction, the lower byte of
the jump address is obtained from a table stored in program
memory, with the Accumulator serving as the low order byte
of a pointer into program memory. For purposes of access-
ing program memory, the contents of the Accumulator are
written to PCL (temporarily). The data pointed to by the Pro-
gram Counter (PCH/PCL) is loaded into PCL, while PCH re-
mains unchanged.
Software Trap Interrupt (INTR)
Vector Interrupt Select (VIS)
12.4.3 Load and Exchange Instructions
The load and exchange instructions write byte values in reg-
isters or memory. The addressing mode determines the
source of the data.
Example: Jump Indirect
JID
Load (LD)
Reg/
Memory
PCU
Contents
Before
01 Hex
C4 Hex
26 Hex
Contents
After
Load Accumulator Indirect (LAID)
Exchange (X)
01 Hex
32 Hex
26 Hex
PCL
12.4.4 Logical Instructions
The logical instructions perform the operations AND, OR,
and XOR (Exclusive OR). Other logical operations can be
performed by combining these basic operations. For ex-
ample, complementing is accomplished by exclusiveORing
the Accumulator with FF Hex.
Accumulator
Memory
Location
0126 Hex
32 Hex
32 Hex
The VIS instruction is a special case of the Indirect Transfer
of Control addressing mode, where the double-byte vector
associated with the interrupt is transferred from adjacent ad-
dresses in program memory into the Program Counter in or-
der to jump to the associated interrupt service routine.
Logical AND (AND)
Logical OR (OR)
Exclusive OR (XOR)
12.4.5 Accumulator Bit Manipulation Instructions
The Accumulator bit manipulation instructions allow the user
to shift the Accumulator bits and to swap its two nibbles.
12.4 INSTRUCTION TYPES
The instruction set contains a wide variety of instructions.
The available instructions are listed below, organized into re-
lated groups.
Rotate Right Through Carry (RRC)
Rotate Left Through Carry (RLC)
Swap Nibbles of Accumulator (SWAP)
Some instructions test a condition and skip the next instruc-
tion if the condition is not true. Skipped instructions are ex-
ecuted as no-operation (NOP) instructions.
12.4.6 Stack Control Instructions
Push Data onto Stack (PUSH)
Pop Data off of Stack (POP)
12.4.1 Arithmetic Instructions
The arithmetic instructions perform binary arithmetic such as
addition and subtraction, with or without the Carry bit.
12.4.7 Memory Bit Manipulation Instructions
Add (ADD)
The memory bit manipulation instructions allow the user to
set and reset individual bits in memory.
Add with Carry (ADC)
Subtract (SUB)
Set Bit (SBIT)
Subtract with Carry (SUBC)
Increment (INC)
Reset Bit (RBIT)
Reset Pending Bit (RPND)
Decrement (DEC)
Decimal Correct (DCOR)
Clear Accumulator (CLR)
Set Carry (SC)
12.4.8 Conditional Instructions
The conditional instruction test a condition. If the condition is
true, the next instruction is executed in the normal manner; if
the condition is false, the next instruction is skipped.
Reset Carry (RC)
If Equal (IFEQ)
If Not Equal (IFNE)
12.4.2 Transfer-of-Control Instructions
If Greater Than (IFGT)
If Carry (IFC)
The transfer-of-control instructions change the usual se-
quential program flow by altering the contents of the Pro-
gram Counter. The Jump to Subroutine instructions save the
Program Counter contents on the stack before jumping; the
Return instructions pop the top of the stack back into the
Program Counter.
If Not Carry (IFNC)
If Bit (IFBIT)
If B Pointer Not Equal (IFBNE)
And Skip if Zero (ANDSZ)
Decrement Register and Skip if Zero (DRSZ)
Jump Relative (JP)
Jump Absolute (JMP)
Jump Absolute Long (JMPL)
Jump Indirect (JID)
Jump to Subroutine (JSR)
37
www.national.com
12.0 Instruction Set (Continued)
Registers
C
1 Bit of PSW Register for Carry
1 Bit of PSW Register for Half Carry
12.4.9 No-Operation Instruction
HC
GIE
The no-operation instruction does nothing, except to occupy
space in the program memory and time in execution.
1 Bit of PSW Register for Global Interrupt
Enable
No-Operation (NOP)
Note: The VIS is a special case of the Indirect Transfer of Control addressing
mode, where the double byte vector associated with the interrupt is
transferred from adjacent addresses in the program memory into the
program counter (PC) in order to jump to the associated interrupt ser-
vice routine.
VU
VL
Interrupt Vector Upper Byte
Interrupt Vector Lower Byte
Symbols
[B]
Memory Indirectly Addressed by B Register
Memory Indirectly Addressed by X Register
Direct Addressed Memory
12.5 REGISTER AND SYMBOL DEFINITION
[X]
The following abbreviations represent the nomenclature
used in the instruction description and the COP8
cross-assembler.
MD
Mem
Meml
Direct Addressed Memory or [B]
Direct Addressed Memory or [B] or
Immediate Data
Registers
A
8-Bit Accumulator Register
8-Bit Address Register
8-Bit Address Register
8-Bit Stack Pointer Register
15-Bit Program Counter Register
Upper 7 Bits of PC
Imm
Reg
8-Bit Immediate Data
B
Register Memory: Addresses F0 to FF
(Includes B, X and SP)
X
SP
PC
PU
PL
Bit
←
↔
Bit Number (0 to 7)
Loaded with
Exchanged with
Lower 8 Bits of PC
12.6 INSTRUCTION SET SUMMARY
←
←
ADD
ADC
A,Meml
A,Meml
ADD
A
A
A + Meml
A + Meml + C, C Carry,
←
ADD with Carry
←
HC Half Carry
← ←
A − MemI + C, C Carry,
SUBC
A,Meml
Subtract with Carry
A
←
HC Half Carry
←
AND
ANDSZ
OR
A,Meml
A,Imm
A,Meml
A,Meml
MD,Imm
A,Meml
A,Meml
A,Meml
#
Logical AND
A
A and Meml
Logical AND Immed., Skip if Zero
Logical OR
Skip next if (A and Imm) = 0
←
←
A
A
A or Meml
XOR
IFEQ
IFEQ
IFNE
IFGT
IFBNE
DRSZ
SBIT
RBIT
IFBIT
RPND
X
Logical EXclusive OR
IF EQual
A xor Meml
Compare MD and Imm, Do next if MD = Imm
Compare A and Meml, Do next if A = Meml
IF EQual
≠
Compare A and Meml, Do next if A Meml
IF Not Equal
>
IF Greater Than
Compare A and Meml, Do next if A Meml
≠
If B Not Equal
Do next if lower 4 bits of B Imm
←
Reg
Decrement Reg., Skip if Zero
Set BIT
Reg Reg − 1, Skip if Reg = 0
#
#
#
,Mem
,Mem
,Mem
1 to bit, Mem (bit = 0 to 7 immediate)
0 to bit, Mem
Reset BIT
#
IF BIT
If bit , A or Mem is true do next instruction
Reset PeNDing Flag
EXchange A with Memory
EXchange A with Memory [X]
LoaD A with Memory
LoaD A with Memory [X]
LoaD B with Immed.
LoaD Memory Immed.
LoaD Register Memory Immed.
EXchange A with Memory [B]
EXchange A with Memory [X]
Reset Software Interrupt Pending Flag
↔
↔
←
←
←
A,Mem
A,[X]
A
A
A
A
B
Mem
[X]
X
LD
A,Meml
A,[X]
Meml
[X]
LD
LD
B,Imm
Imm
←
Mem Imm
LD
Mem,Imm
Reg,Imm
←
Reg Imm
LD
↔
↔
←
±
±
±
±
X
A, [B
A, [X
]
]
A
A
[B], (B
[X], (X
B
X
1)
1)
←
X
www.national.com
38
12.0 Instruction Set (Continued)
←
←
←
←
±
±
1)
LD
A, [B ]
LoaD A with Memory [B]
LoaD A with Memory [X]
LoaD Memory [B] Immed.
CLeaR A
A
A
[B], (B
B
±
±
LD
A, [X ]
[X], (X X 1)
←
←
±
±
LD
[B ],Imm
[B] Imm, (B B 1)
←
A
←
A
←
A
←
A
←
A
→
C
←
C
CLR
INC
A
A
A
0
INCrement A
A + 1
DEC
LAID
DCOR
RRC
RLC
SWAP
SC
DECrement A
A − 1
Load A InDirect from ROM
Decimal CORrect A
Rotate A Right thru C
Rotate A Left thru C
SWAP nibbles of A
Set C
ROM (PU,A)
A
A
A
A
BCD correction of A (follows ADC, SUBC)
→
←
→
←
→
A0 C
A7
A7
…
…
←
←
A0 C, HC A0
↔
A7…A4 A3…A0
←
←
←
←
C
C
1, HC
0, HC
1
0
RC
Reset C
IFC
IF C
IF C is true, do next instruction
IFNC
POP
PUSH
VIS
IF Not C
If C is not true, do next instruction
← ←
SP SP + 1, A [SP]
A
A
POP the stack into A
PUSH A onto the stack
Vector to Interrupt Service Routine
Jump absolute Long
Jump absolute
←
←
[SP] A, SP SP − 1
←
←
PU [VU], PL [VL]
←
PC ii (ii = 15 bits, 0 to 32k)
JMPL
JMP
JP
Addr.
Addr.
Disp.
Addr.
Addr.
←
PC9…0 i (i = 12 bits)
←
PC PC + r (r is −31 to +32, except 1)
Jump relative short
Jump SubRoutine Long
Jump SubRoutine
Jump InDirect
← ← ←
[SP] PL, [SP−1] PU,SP−2, PC ii
JSRL
JSR
JID
←
←
←
[SP] PL, [SP−1] PU,SP−2, PC9…0
i
←
PL ROM (PU,A)
← ←
SP + 2, PL [SP], PU [SP−1]
RET
RETSK
RETurn from subroutine
RETurn and SKip
←
←
SP + 2, PL [SP],PU [SP−1],
skip next instruction
←
←
←
RETI
INTR
NOP
RETurn from Interrupt
Generate an Interrupt
No OPeration
SP + 2, PL [SP],PU [SP−1],GIE
1
←
←
←
[SP] PL, [SP−1] PU, SP−2, PC 0FF
←
PC PC + 1
39
www.national.com
Instructions Using A & C
12.0 Instruction Set (Continued)
CLRA
INCA
DECA
LAID
1/1
1/1
1/1
1/3
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/3
1/3
2/2
12.7 INSTRUCTION EXECUTION TIME
Most instructions are single byte (with immediate addressing
mode instructions taking two bytes).
Most single byte instructions take one cycle time to execute.
Skipped instructions require x number of cycles to be
skipped, where x equals the number of bytes in the skipped
instruction opcode.
DCORA
RRCA
RLCA
SWAPA
SC
See the BYTES and CYCLES per INSTRUCTION table for
details.
Bytes and Cycles per Instruction
RC
The following table shows the number of bytes and cycles for
each instruction in the format of byte/cycle.
IFC
Arithmetic and Logic Instructions
IFNC
PUSHA
POPA
ANDSZ
[B]
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
Direct
3/4
Immed.
2/2
ADD
ADC
SUBC
AND
OR
3/4
2/2
Transfer of Control Instructions
3/4
2/2
3/4
2/2
JMPL
JMP
JP
3/4
2/3
1/3
3/5
2/5
1/3
1/5
1/5
1/5
1/5
1/7
1/1
3/4
2/2
XOR
IFEQ
IFGT
IFBNE
DRSZ
SBIT
RBIT
IFBIT
3/4
2/2
3/4
2/2
JSRL
JSR
3/4
2/2
JID
1/3
3/4
3/4
3/4
VIS
1/1
1/1
1/1
RET
RETSK
RETI
INTR
NOP
RPND
1/1
Memory Transfer Instructions
Register
Indirect
Direct Immed.
Register Indirect
Auto Incr. & Decr.
[B+, B−] [X+, X−]
1/2 1/3
1/3
[B]
[X]
1/3
1/3
X A, (Note 27)
LD A, (Note 27)
LD B, Imm
1/1
1/1
2/3
2/3
2/2
1/1
2/2
1/2
<
(If B 16)
>
(If B 15)
LD B, Imm
LD Mem, Imm
LD Reg, Imm
IFEQ MD, Imm
2/2
3/3
2/3
3/3
2/2
>
Memory location addressed by B or X or directly.
Note 27:
=
www.national.com
40
12.0 Instruction Set (Continued)
N i b b l e L o w e r
41
www.national.com
13.0 Mask Options For COP8SEC5
14.0 Development Support
The mask options for this device are described below. These
options are programmed at the same time as the ROM pat-
tern and therefore must be submitted with the ROM pattern.
14.1 OVERVIEW
National is engaged with an international community of inde-
pendent 3rd party vendors who provide hardware and soft-
ware development tool support. Through National’s interac-
tion and guidance, these tools cooperate to form a choice of
solutions that fits each developer’s needs.
OPTION 1: Clock configuration
=1 Crystal Oscillator (CKI/10)
G7 (CKO) is clock generator output to
crystal/resonator
This section provides a summary of the tool and develop-
ment kits currently available. Up-to-date information, selec-
tion guides, free tools, demos, updates, and purchase infor-
mation can be obtained at our web site at:
www.national.com/cop8.
CKI is the clock input
=2 Single-pin R/C Controlled Oscillator
G7 is available as a HALT restart and/or general pur-
pose input
CKI is the clock input
OPTION 2: HALT
14.2 SUMMARY OF TOOLS
COP8 Evaluation Tools
=1 Enable HALT mode
•
COP8–NSEVAL: Free Software Evaluation package for
Windows. A fully integrated evaluation environment for
COP8, including versions of WCOP8 IDE (Integrated De-
velopment Environment), COP8-NSASM, COP8-MLSIM,
=2 Disable HALT mode
OPTION 3: WATCHDOG
=1 Enable WATCHDOG output on Pin G1
™
COP8C, DriveWay COP8, Manuals, and other COP8
=2 Disable WATCHDOG output on G1 and Enable stan-
dard I/O on Pin G1
information.
•
•
COP8–MLSIM: Free Instruction Level Simulator tool for
Windows. For testing and debugging software instruc-
tions only (No I/O or interrupt support).
OPTION 4: BONDING
=1 Reserved
=2 20 pin SO
COP8–EPU: Very Low cost COP8 Evaluation & Pro-
gramming Unit. Windows based evaluation and
hardware-simulation tool, with COP8 device programmer
and erasable samples. Includes COP8-NSDEV, Drive-
way COP8 Demo, MetaLink Debugger, I/O cables and
power supply.
=3 16 pin SO (Note: ROM Mask prototypes of 16 pin SO
devices will be provided in 16 pin ceramic DIP pack-
age)
13.1 Options for COP8SER7
COP8SER7 is only available in two versions:
•
•
COP8–EVAL-HIxx: Low cost target application evalua-
tion and development board for COP8Sx Families, from
Hilton Inc. Real-time environment with integrated A/D,
Temp Sensor, and Peripheral I/O.
COP8SER7XXM8–XE Crystal oscillator, HALT enabled,
WATCHDOG enabled.
COP8SER7XXM8–RE R/C oscillator, HALT enabled,
WATCHDOG enabled.
COP8–EVAL-ICUxx: Very Low cost evaluation and de-
sign test board for COP8ACC and COP8SGx Families,
from ICU. Real-time environment with add-on A/D, D/A,
and EEPROM. Includes software routines and reference
designs.
•
Manuals, Applications Notes, Literature: Available free
from our web site at: www.national.com/cop8.
COP8 Integrated Software/Hardware Design Develop-
ment Kits
•
COP8-EPU: Very Low cost Evaluation & Programming
Unit. Windows based development and hardware-
simulation tool for COPSx/xG families, with COP8 device
programmer and samples. Includes COP8-NSDEV,
Driveway COP8 Demo, MetaLink Debugger, cables and
power supply.
•
COP8-DM: Moderate cost Debug Module from MetaLink.
A Windows based, real-time in-circuit emulation tool with
COP8 device programmer. Includes COP8-NSDEV,
DriveWay COP8 Demo, MetaLink Debugger, power sup-
ply, emulation cables and adapters.
COP8 Development Languages and Environments
•
COP8-NSASM: Free COP8 Assembler v5 for Win32.
Macro assembler, linker, and librarian for COP8 software
development. Supports all COP8 devices. (DOS/Win16
v4.10.2 available with limited support). (Compatible with
WCOP8 IDE, COP8C, and DriveWay COP8).
www.national.com
42
COP8 Productivity Enhancement Tools
14.0 Development Support (Continued)
•
WCOP8 IDE: Very Low cost IDE (Integrated Develop-
ment Environment) from KKD. Supports COP8C, COP8-
NSASM, COP8-MLSIM, DriveWay COP8, and MetaLink
debugger under a common Windows Project Manage-
ment environment. Code development, debug, and emu-
lation tools can be launched from the project window
framework.
•
COP8-NSDEV: Very low cost Software Development
Package for Windows. An integrated development envi-
ronment for COP8, including WCOP8 IDE, COP8C (lim-
ited version), COP8-NSASM, COP8-MLSIM.
•
COP8C: Moderately priced C Cross-Compiler and Code
Development System from Byte Craft (no code limit). In-
cludes BCLIDE (Byte Craft Limited Integrated Develop-
ment Environment) for Win32, editor, optimizing C Cross-
Compiler, macro cross assembler, BC-Linker, and
MetaLink tools support. (DOS/SUN versions available;
Compiler is installable under WCOP8 IDE; Compatible
with DriveWay COP8).
•
DriveWay-COP8: Low cost COP8 Peripherals Code
Generation tool from Aisys Corporation. Automatically
generates tested and documented C or Assembly source
code modules containing I/O drivers and interrupt han-
dlers for each on-chip peripheral. Application specific
code can be inserted for customization using the inte-
grated editor. (Compatible with COP8-NSASM, COP8C,
and WCOP8 IDE.)
•
•
EWCOP8-KS: Very Low cost ANSI C-Compiler and Em-
bedded Workbench from IAR (Kickstart version:
COP8Sx/Fx only with 2k code limit; No FP). A fully inte-
grated Win32 IDE, ANSI C-Compiler, macro assembler,
editor, linker, Liberian, C-Spy simulator/debugger, PLUS
MetaLink EPU/DM emulator support.
•
•
COP8-UTILS: Free set of COP8 assembly code ex-
amples, device drivers, and utilities to speed up code de-
velopment.
COP8-MLSIM: Free Instruction Level Simulator tool for
Windows. For testing and debugging software instruc-
tions only (No I/O or interrupt support).
EWCOP8-AS: Moderately priced COP8 Assembler and
Embedded Workbench from IAR (no code limit). A fully in-
tegrated Win32 IDE, macro assembler, editor, linker, li-
brarian, and C-Spy high-level simulator/debugger with
I/O and interrupts support. (Upgradeable with optional
C-Compiler and/or MetaLink Debugger/Emulator sup-
port).
COP8 Real-Time Emulation Tools
•
COP8-DM: MetaLink Debug Module. A moderately
priced real-time in-circuit emulation tool, with COP8 de-
vice programmer. Includes MetaLink Debugger, power
supply, emulation cables and adapters.
•
EWCOP8-BL: Moderately priced ANSI C-Compiler and
Embedded Workbench from IAR (Baseline version: All
COP8 devices; 4k code limit; no FP). A fully integrated
Win32 IDE, ANSI C-Compiler, macro assembler, editor,
linker, librarian, and C-Spy high-level simulator/debugger.
(Upgradeable; CWCOP8-M MetaLink tools interface sup-
port optional).
•
IM-COP8: MetaLink iceMASTER®. A full featured, real-
time in-circuit emulator for COP8 devices. Includes
COP8-NSDEV, Driveway COP8 Demo, MetaLink Win-
dows Debugger, and power supply. Package-specific
probes and surface mount adaptors are ordered sepa-
rately.
COP8 Device Programmer Support
•
•
EWCOP8: Full featured ANSI C-Compiler and Embed-
ded Workbench for Windows from IAR (no code limit). A
fully integrated Win32 IDE, ANSI C-Compiler, macro as-
sembler, editor, linker, librarian, and C-Spy high-level
simulator/debugger. (CWCOP8-M MetaLink tools inter-
face support optional).
•
MetaLink’s EPU and Debug Module include development
device programming capability for COP8 devices.
•
Third-party programmers and automatic handling equip-
ment cover needs from engineering prototype and pilot
production, to full production environments.
EWCOP8-M: Full featured ANSI C-Compiler and Embed-
ded Workbench for Windows from IAR (no code limit). A
fully integrated Win32 IDE, ANSI C-Compiler, macro as-
sembler, editor, linker, librarian, C-Spy high-level
simulator/debugger, PLUS MetaLink debugger/hardware
interface (CWCOP8-M).
•
Factory programming available for high-volume require-
ments.
43
www.national.com
14.0 Development Support (Continued)
14.3 TOOLS ORDERING NUMBERS FOR THE COP8SEx FAMILY DEVICES
Vendor
Tools
Order Number
COP8-NSEVAL
Cost
Notes
National COP8-NSEVAL
COP8-NSASM
COP8-MLSIM
COP8-NSDEV
COP8-EPU
Free Web site download
COP8-NSASM
Free Included in EPU and DM. Web site download
Free Included in EPU and DM. Web site download
COP8-MLSIM
COP8-NSDEV
VL
VL
Included in EPU and DM. Order CD from website
32k Eraseable or OTP devices
Not available for this device
Contact metaLink
COP8SER7
COP8-DM
Development
Devices
IM-COP8
MetaLink COP8-EPU
COP8-DM
Contact MetaLink
Not available for this device
DM5-COP8-SEx (15
MHz), plus PS-10, plus
DM-COP8/xxx (ie. 28D)
M
Included p/s (PS-10), target cable of choice (DIP or
SOIC; i.e. DM-COP8/28D), 16/20/28/40 DIP/SO and
44 PLCC programming sockets. Add target adapter (if
needed)
DM Target
Adapters
MHW-CNVxx (xx = 33, 34
etc.)
L
L
H
DM target converters for 20SO/28SO; (i.e.
MHW-CNV38 for 20 pin DIP to SO package converter)
MHW-COP8-PGMA-DS
For programming 16/20/28 SOIC and 44 PLCC on the
EPU
IM-COP8
IM-COP8-AD-464 (-220)
(10 MHz maximum)
Base unit 10 MHz; -220 = 220V; add probe card
(required) and target adapter (if needed); included
software and manuals
IM Probe Card
PC-COP8SE28DW-AD-10
PC-COP8SE40DW-AD-10
M
M
L
10 MHz 28 DIP probe card; 2.5V to 6.0V
10 MHz 40 DIP probe card; 2.5V to 6.0V
16 or 20 or 28 pin SOIC adapter for probe card
MHW-SOICxx (xx = 16,
20, 28)
ICU or
COP8-EVAL-ICUxx Not available for this device
National
KKD
IAR
WCOP8-IDE
EWCOP8-xx
COP8C
WCOP8-IDE
See summary above
COP8C
VL
Included in EPU and DM
L - H Included all software and manuals
Byte
Craft
M
Included all software and manuals
Aisys
DriveWay COP8
DriveWay COP8
Contact vendors
L
Included all software and manuals
OTP Programmers
L - H For approved programmer listings and vendor
information, go to our OTP support page at:
www.national.com/cop8
<
Cost: Free; VL = $100; L = $100 - $300; M = $300 - $1k; H = $1k - $3k; VH = $3k - $5k
www.national.com
44
14.0 Development Support (Continued)
14.4 WHERE TO GET TOOLS
Tools are ordered directly from the following vendors. Please go to the vendor’s web site for current listings of distributors.
Vendor
Home Office
U.S.A.: Santa Clara, CA
1-408-327-8820
Electronic Sites
Other Main Offices
Distributors
Aisys
www.aisysinc.com
@
info aisysinc.com
fax: 1-408-327-8830
U.S.A.
Byte Craft
IAR
www.bytecraft.com
Distributors
@
1-519-888-6911
info bytecraft.com
fax: 1-519-746-6751
Sweden: Uppsala
+46 18 16 78 00
fax: +46 18 16 78 38
www.iar.se
U.S.A.: San Francisco
1-415-765-5500
@
info iar.se
@
info iar.com
fax: 1-415-765-5503
U.K.: London
@
info iarsys.co.uk
@
info iar.de
+44 171 924 33 34
fax: +44 171 924 53 41
Germany: Munich
+49 89 470 6022
fax: +49 89 470 956
Switzeland: Hoehe
+41 34 497 28 20
fax: +41 34 497 28 21
ICU
Sweden: Polygonvaegen
+46 8 630 11 20
www.icu.se
@
support icu.se
@
fax: +46 8 630 11 70
Denmark:
support icu.ch
KKD
www.kkd.dk
MetaLink
U.S.A.: Chandler, AZ
1-800-638-2423
www.metaice.com
Germany: Kirchseeon
80-91-5696-0
@
sales metaice.com
@
fax: 1-602-926-1198
support metaice.com
fax: 80-91-2386
@
bbs: 1-602-962-0013
www.metalink.de
islanger metalink.de
Distributors Worldwide
National
U.S.A.: Santa Clara, CA
1-800-272-9959
www.national.com/cop8
Europe: +49 (0) 180 530 8585
fax: +49 (0) 180 530 8586
Distributors Worldwide
@
support nsc.com
@
fax: 1-800-737-7018
europe.support nsc.com
The following companies have approved COP8 program-
mers in a variety of configurations. Contact your local office
or distributor. You can link to their web sites and get the lat-
est listing of approved programmers from National’s COP8
OTP Support page at: www.national.com/cop8.
14.5 CUSTOMER SUPPORT
Complete product information and technical support is avail-
able from National’s customer response centers, and from
our on-line COP8 customer support sites.
Advantech; Advin; BP Microsystems; Data I/O; Hi-Lo Sys-
tems; ICE Technology; Lloyd Research; Logical Devices;
MQP; Needhams; Phyton; SMS; Stag Programmers; Sys-
tem General; Tribal Microsystems; Xeltek.
45
www.national.com
Physical Dimensions inches (millimeters) unless otherwise noted
Molded SO Wide Body Package (WM)
Order Number COP8SEC516M,
NS Package Number M16B
Molded SO Wide Body Package (WM)
Order Number COP8SEC520M,
NS Package Number M20B
www.national.com
46
Notes
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Corporation
Americas
Tel: 1-800-272-9959
Fax: 1-800-737-7018
Email: support@nsc.com
National Semiconductor
Europe
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Email: nsj.crc@jksmtp.nsc.com
Fax: 81-3-5639-7507
Fax: +49 (0) 180-530 85 86
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 87 90
Email: ap.support@nsc.com
www.national.com
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
相关型号:
COP8SEC516M8XXX
IC 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PDSO16, PLASTIC, SOP-16, Microcontroller
NSC
COP8SEC520M7XXX
IC 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PDSO20, PLASTIC, SOP-20, Microcontroller
NSC
COP8SEC520M8XXX
IC 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PDSO20, PLASTIC, SOP-20, Microcontroller
NSC
©2020 ICPDF网 联系我们和版权申明