CY74FCT138CTSOCTE4 [TI]
FCT SERIES, OTHER DECODER/DRIVER, INVERTED OUTPUT, PDSO16, GREEN, SOIC-16;型号: | CY74FCT138CTSOCTE4 |
厂家: | TEXAS INSTRUMENTS |
描述: | FCT SERIES, OTHER DECODER/DRIVER, INVERTED OUTPUT, PDSO16, GREEN, SOIC-16 驱动 输入元件 光电二极管 输出元件 逻辑集成电路 |
文件: | 总12页 (文件大小:474K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
CY54FCT138T, CY74FCT138T
1-OF-8 DECODERS
SCCS013B – MAY 1994 – REVISED OCTOBER 2001
CY54FCT138T . . . D PACKAGE
CY74FCT138T . . . Q OR SO PACKAGE
(TOP VIEW)
Function, Pinout, and Drive Compatible
With FCT and F Logic
Reduced V
Equivalent FCT Functions
(Typically = 3.3 V) Versions of
OH
A
A
A
E
E
E
O
V
CC
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
0
1
2
1
2
3
7
O
O
O
O
O
O
O
0
1
2
3
4
5
6
Edge-Rate Control Circuitry for
Significantly Improved Noise
Characteristics
I
Supports Partial-Power-Down Mode
off
Operation
Matched Rise and Fall Times
GND
Fully Compatible With TTL Input and
Output Logic Levels
CY54FCT138T . . . L PACKAGE
(TOP VIEW)
Dual 1-of-8 Decoder With Enables
ESD Protection Exceeds JESD 22
– 2000-V Human-Body Model (A114-A)
– 200-V Machine Model (A115-A)
3
2 1 20 19
18
O
O
A
E
4
5
6
7
8
1
2
2
1
– 1000-V Charged-Device Model (C101)
17
16
15
14
CY54FCT138T
– 32-mA Output Sink Current
– 12-mA Output Source Current
NC
NC
O
3
O
4
E
2
E
3
CY74FCT138T
9 10 11 12 13
– 64-mA Output Sink Current
– 32-mA Output Source Current
NC – No internal connection
description
The ’FCT138T devices are 1-of-8 decoders. These devices accept three binary weighted inputs (A , A , A )
0
1
2
and, when enabled, provide eight mutually exclusive active-low outputs (O –O ). The ’FCT138T devices
0
7
feature three enable inputs: two active low (E , E ) and one active high (E ).
1
2
3
All outputs are high unless E and E are low and E is high. This multiple-enable function allows easy parallel
1
2
3
expansion of the device to a 1-of-32 (five lines to 32 lines) decoder with just four ’FCT138T devices and one
inverter.
These devices are fully specified for partial-power-down applications using I . The I circuitry disables the
off
off
outputs, preventing damaging current backflow through the device when it is powered down.
PIN DESCRIPTION
NAME
DESCRIPTION
Address inputs
A
E , E
Enable inputs (active low)
Enable input (active high)
Outputs
1
2
E
3
O
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright 2001, Texas Instruments Incorporated
On products compliant to MIL-PRF-38535, all parameters are tested
unless otherwise noted. On all other products, production
processing does not necessarily include testing of all parameters.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
CY54FCT138T, CY74FCT138T
1-OF-8 DECODERS
SCCS013B – MAY 1994 – REVISED OCTOBER 2001
ORDERING INFORMATION
SPEED
(ns)
ORDERABLE
TOP-SIDE
MARKING
†
PACKAGE
T
A
PART NUMBER
CY74FCT138CTQCT
CY74FCT138CTSOC
CY74FCT138CTSOCT
CY74FCT138ATQCT
CY74FCT138ATSOC
CY74FCT138ATSOCT
CY74FCT138TQCT
CY54FCT138CTLMB
CY54FCT138TLMB
CY54FCT138TDMB
QSOP – Q
SOIC – SO
QSOP – Q
SOIC – SO
Tape and reel
Tube
5
5
FT138-3
FCT138C
FT138-1
FCT138A
FT138
Tape and reel
Tape and reel
Tube
5
–40°C to 85°C
5.8
5.8
5.8
9
Tape and reel
Tape and reel
Tube
QSOP – Q
LCC – L
6
–55°C to 125°C
LCC – L
Tube
12
12
CDIP – D
Tube
†
Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are
available at www.ti.com/sc/package.
FUNCTION TABLE
INPUTS
OUTPUTS
E
1
E
2
E
3
A
A
A
O
O
O
O
O
O
O
O
7
0
1
2
0
1
2
3
4
5
6
H
X
X
X
X
X
H
H
H
H
H
H
H
H
X
X
L
L
L
L
L
L
L
L
H
X
L
L
L
L
L
L
L
L
X
L
X
X
L
X
X
L
X
X
L
H
H
L
H
H
H
L
H
H
H
H
L
H
H
H
H
H
L
H
H
H
H
H
H
L
H
H
H
H
H
H
H
L
H
H
H
H
H
H
H
H
L
H
H
H
H
H
H
H
H
H
L
H
H
H
H
H
H
H
H
H
L
L
L
H
H
H
H
H
H
H
H
H
L
L
H
H
H
H
H
H
H
L
L
H
H
H
H
H
H
H
H
H
H
H
H
H
H
L
L
H
H
H
H
H
H
H
H
H
H = High logic level, L = Low logic level, X = Don’t care
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
CY54FCT138T, CY74FCT138T
1-OF-8 DECODERS
SCCS013B – MAY 1994 – REVISED OCTOBER 2001
logic diagram (positive logic)
15
O
O
O
O
O
0
1
2
3
4
1
A
A
0
1
14
13
12
11
10
9
2
3
A
2
O
O
O
5
6
7
6
4
E
3
E
1
E
2
7
5
Pin numbers shown are for the D, Q, and SO packages.
†
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage range to ground potential . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V
DC input voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V
DC output voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V
DC output current (maximum sink current/pin) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 mA
Package thermal impedance, θ (see Note 1): Q package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90°C/W
JA
SO package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57°C/W
Ambient temperature range with power applied, T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 135°C
A
Storage temperature range, T
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
stg
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: The package thermal impedance is calculated in accordance with JESD 51-7.
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
CY54FCT138T, CY74FCT138T
1-OF-8 DECODERS
SCCS013B – MAY 1994 – REVISED OCTOBER 2001
recommended operating conditions (see Note 2)
CY54FCT138T
MIN NOM MAX
CY74FCT138T
MIN NOM MAX
UNIT
V
V
V
Supply voltage
4.5
2
5
5.5
4.75
2
5
5.25
V
V
CC
High-level input voltage
Low-level input voltage
High-level output current
Low-level output current
Operating free-air temperature
IH
0.8
–12
32
0.8
–32
64
V
IL
I
I
mA
mA
°C
OH
OL
T
A
–55
125
–40
85
NOTE 2: All unused inputs of the device must be held at V
or GND to ensure proper device operation.
CC
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
CY54FCT138T
CY74FCT138T
PARAMETER
TEST CONDITIONS
UNIT
†
TYP
†
TYP
MIN
MAX
MIN
MAX
V
V
V
= 4.5 V,
= 4.75 V,
= 4.5 V,
I
I
I
I
I
I
I
= –18 mA
= –18 mA
–0.7
–1.2
CC
CC
CC
IN
V
V
IK
–0.7
–1.2
IN
= –12 mA
= –32 mA
= –15 mA
= 32 mA
= 64 mA
2.4
3.3
OH
OH
OH
OL
OL
V
OH
2
V
V
CC
= 4.75 V
2.4
3.3
V
V
= 4.5 V,
0.3
0.2
0.55
CC
V
V
V
V
OL
= 4.75 V,
0.3
0.2
0.55
CC
All inputs
hys
V
V
V
V
V
V
V
V
V
V
V
= 5.5 V,
= 5.25 V,
= 5.5 V,
= 5.25 V,
= 5.5 V,
= 5.25 V,
= 5.5 V,
= 5.25 V,
= 0 V,
V
V
V
V
V
V
V
V
V
V
V
= V
= V
5
±1
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
IN
CC
CC
I
I
I
µA
I
5
±1
±1
IN
= 2.7 V
= 2.7 V
= 0.5 V
= 0.5 V
IN
µA
µA
IH
IL
IN
±1
IN
IN
= 0 V
–60
–120
–225
OUT
OUT
OUT
‡
mA
µA
I
I
I
OS
= 0 V
–60
–120
–225
±1
= 4.5 V
±1
off
= 5.5 V,
= 5.25 V,
≤ 0.2 V,
V
V
≥ V
≥ V
– 0.2 V
– 0.2 V
0.1
0.5
0.2
IN
IN
IN
CC
mA
CC
≤ 0.2 V,
0.1
0.5
0.2
2
IN
CC
§
2
V
CC
V
CC
V
CC
= 5.5 V, V = 3.4 V , f = 0, Outputs open
IN
1
∆I
mA
CC
§
= 5.25 V, V = 3.4 V , f = 0, Outputs open
IN
1
= 5.5 V, Outputs open, One bit switching at 50% duty
– 0.2 V
0.06
0.12
cycle, V ≤ 0.2 V or V ≥ V
IN IN CC
mA/
MHz
¶
I
CCD
V
CC
= 5.25 V, Outputs open, One bit switching at 50%
0.06
0.12
duty cycle, V ≤ 0.2 V or V ≥ V
– 0.2 V
IN IN CC
†
‡
Typical values are at V
CC
= 5 V, T = 25°C.
A
Not more than one output should be shorted at a time. Duration of short should not exceed one second. The use of high-speed test apparatus
and/or sample-and-hold techniques are preferable to minimize internal chip heating and more accurately reflect operational values. Otherwise,
prolonged shorting of a high output can raise the chip temperature well above normal and cause invalid readings in other parametric tests. In
any sequence of parameter tests, I
tests should be performed last.
OS
§
¶
Per TTL-driven input (V = 3.4 V); all other inputs at V
or GND
IN CC
This parameter is derived for use in total power-supply calculations.
4
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
CY54FCT138T, CY74FCT138T
1-OF-8 DECODERS
SCCS013B – MAY 1994 – REVISED OCTOBER 2001
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted) (continued)
CY54FCT138T
CY74FCT138T
PARAMETER
TEST CONDITIONS
UNIT
†
TYP
†
TYP
MIN
MAX
MIN
MAX
One output
switching
V
V
≤ 0.2 V or
≥ V – 0.2 V
CC
V
= 5.5 V,
IN
IN
CC
Outputs open,
Switch E , E , or
0.7
1
1.4
at f = 10 MHz
1
1
2
at 50% duty
cycle
E
3
V
IN
= 3.4 V or GND
2.4
#
I
C
mA
One output
switching
V
V
≤ 0.2 V or
V
= 5.25 V,
IN
IN
CC
||
||
0.7
1
1.4
≥ V
CC
– 0.2 V
Outputs open,
Switch E , E , or
at f = 10 MHz
1
1
2
at 50% duty
cycle
E
3
V
IN
= 3.4 V or GND
2.4
C
C
5
9
10
12
5
9
10
12
pF
pF
i
o
†
#
Typical values are at V
CC
= 5 V, T = 25°C.
A
I
= I
+ ∆I
× D × N + I
(f /2 + f × N )
C
CC
CC
H
T
CCD 0 1 1
Where:
I
I
∆I
D
N
= Total supply current
= Power-supply current with CMOS input levels
C
CC
CC
H
T
= Power-supply current for a TTL high input (V = 3.4 V)
IN
= Duty cycle for TTL inputs high
= Number of TTL inputs at D
H
I
f
f
= Dynamic current caused by an input transition pair (HLH or LHL)
= Clock frequency for registered devices, otherwise zero
= Input signal frequency
CCD
0
1
N
= Number of inputs changing at f
1
1
All currents are in milliamperes and all frequencies are in megahertz.
||
Values for these conditions are examples of the I
CC
formula.
switching characteristics over operating free-air temperature range (see Figure 1)
CY54FCT138T CY54FCT138CT
FROM
(INPUT)
TO
(OUTPUT)
PARAMETER
UNIT
ns
MIN
1.5
1.5
1.5
1.5
1.5
1.5
MAX
12
MIN
1.5
1.5
1.5
1.5
1.5
1.5
MAX
6
t
t
t
t
t
t
PLH
PHL
PLH
PHL
PLH
PHL
A
O
O
O
12
6
12.5
12.5
12.5
12.5
6.1
6.1
6.1
6.1
ns
E
1
or E
2
E
3
ns
switching characteristics over operating free-air temperature range (see Figure 1)
CY74FCT138T
CY74FCT138AT
CY74FCT138CT
FROM
(INPUT)
TO
(OUTPUT)
PARAMETER
UNIT
ns
MIN
1.5
1.5
1.5
1.5
1.5
1.5
MAX
MIN
1.5
1.5
1.5
1.5
1.5
1.5
MAX
5.8
5.8
5.9
5.9
5.9
5.9
MIN
1.5
1.5
1.5
1.5
1.5
1.5
MAX
t
t
t
t
t
t
9
9
9
9
9
9
5
5
5
5
5
5
PLH
PHL
PLH
PHL
PLH
PHL
A
O
O
O
ns
E
1
or E
2
E
3
ns
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
CY54FCT138T, CY74FCT138T
1-OF-8 DECODERS
SCCS013B – MAY 1994 – REVISED OCTOBER 2001
PARAMETER MEASUREMENT INFORMATION
7 V
Open
GND
S1
500 Ω
From Output
Under Test
From Output
Under Test
Test
Point
TEST
S1
t
/t
Open
7 V
PLH PHL
t /t
C
= 50 pF
C
= 50 pF
L
L
500 Ω
500 Ω
PLZ PZL
/t
(see Note A)
(see Note A)
t
Open
PHZ PZH
LOAD CIRCUIT FOR
TOTEM-POLE OUTPUTS
LOAD CIRCUIT FOR
3-STATE OUTPUTS
3 V
0 V
1.5 V
Timing Input
Data Input
t
w
t
h
t
3 V
su
3 V
0 V
1.5 V
Input
1.5 V
1.5 V
1.5 V
0 V
VOLTAGE WAVEFORMS
PULSE DURATION
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
3 V
0 V
3 V
0 V
Output
Control
1.5 V
1.5 V
1.5 V
1.5 V
Input
t
t
t
t
t
t
PLH
PHL
PLH
PZL
PZH
PLZ
≈3.5 V
V
Output
Waveform 1
(see Note B)
OH
In-Phase
Output
1.5 V
1.5 V
1.5 V
1.5 V
V
V
+ 0.3 V
OL
V
OL
V
OL
t
t
PHL
PHZ
V
V
V
OH
OH
Output
Waveform 2
(see Note B)
Out-of-Phase
Output
– 0.3 V
OH
1.5 V
1.5 V
≈0 V
OL
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
INVERTING AND NONINVERTING OUTPUTS
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
LOW- AND HIGH-LEVEL ENABLING
NOTES: A. includes probe and jig capacitance.
C
L
B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control.
C. The outputs are measured one at a time with one input transition per measurement.
Figure 1. Load Circuit and Voltage Waveforms
6
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
PACKAGE OPTION ADDENDUM
www.ti.com
10-Jun-2014
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(6)
(3)
(4/5)
5962-9223302M2A
ACTIVE
LCCC
FK
20
1
TBD
POST-PLATE
N / A for Pkg Type
-55 to 125
5962-
9223302M2A
CY54FCT
138TLMB
5962-9223302MEA
5962-9223306M2A
ACTIVE
ACTIVE
CDIP
J
16
20
1
1
TBD
TBD
A42
N / A for Pkg Type
N / A for Pkg Type
-55 to 125
-55 to 125
5962-9223302ME
A
CY54FCT138TDMB
LCCC
FK
POST-PLATE
5962-
9223306M2A
CY54FCT
138CTLMB
5962-9223306MEA
ACTIVE
ACTIVE
CDIP
J
16
20
1
1
TBD
TBD
A42
N / A for Pkg Type
N / A for Pkg Type
-55 to 125
-55 to 125
5962-9223306ME
A
CY54FCT138CTLMB
LCCC
FK
POST-PLATE
5962-
9223306M2A
CY54FCT
138CTLMB
CY54FCT138TDMB
CY54FCT138TLMB
ACTIVE
ACTIVE
CDIP
J
16
20
1
1
TBD
TBD
A42
N / A for Pkg Type
N / A for Pkg Type
-55 to 125
-55 to 125
5962-9223302ME
A
CY54FCT138TDMB
LCCC
FK
POST-PLATE
5962-
9223302M2A
CY54FCT
138TLMB
CY74FCT138ATQCT
CY74FCT138ATSOC
CY74FCT138ATSOCG4
CY74FCT138ATSOCT
CY74FCT138CTQCT
CY74FCT138CTQCTE4
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
SSOP
SOIC
SOIC
SOIC
SSOP
SSOP
DBQ
DW
16
16
16
16
16
16
2500
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
Level-2-260C-1 YEAR
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
FT138-1
FCT138A
FCT138A
FCT138A
FT138-3
FT138-3
Green (RoHS
& no Sb/Br)
DW
40
Green (RoHS
& no Sb/Br)
DW
2000
2500
2500
Green (RoHS
& no Sb/Br)
DBQ
DBQ
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
10-Jun-2014
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-40 to 85
Device Marking
Samples
Drawing
Qty
(1)
(2)
(6)
(3)
(4/5)
CY74FCT138CTSOC
CY74FCT138TQCT
ACTIVE
SOIC
DW
16
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
FCT138C
FT138
ACTIVE
SSOP
DBQ
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
10-Jun-2014
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
CY74FCT138ATSOCT
SOIC
DW
16
2000
330.0
16.4
10.75 10.7
2.7
12.0
16.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SOIC DW 16
SPQ
Length (mm) Width (mm) Height (mm)
367.0 367.0 38.0
CY74FCT138ATSOCT
2000
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2014, Texas Instruments Incorporated
相关型号:
CY74FCT138TDC
Decoder/Driver, FCT Series, Inverted Output, CMOS, CDIP16, 0.300 INCH, CERDIP-16
CYPRESS
©2020 ICPDF网 联系我们和版权申明