DAC7571IDBVTG4 [TI]
低功耗轨到轨输出 12 位 I2C 输入 DAC | DBV | 6 | -40 to 105;
| 型号： | DAC7571IDBVTG4 |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | 低功耗轨到轨输出 12 位 I2C 输入 DAC | DBV | 6 | -40 to 105 转换器 数模转换器 |
| 文件： | 总21页 (文件大小：754K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
D
A
C
7
5
1
2
DAC7571
www.ti.com
SLAS374A–FEBRUARY 2003–REVISED JANUARY 2004
+2.7 V to +5.5 V, I2C INTERFACE, VOLTAGE OUTPUT, 12-BIT DIGITAL-TO-ANALOG
CONVERTER
FEATURES
DESCRIPTION
•
•
•
•
•
•
•
Micropower Operation: 140 µA @ 5 V
Power-On Reset to Zero
The DAC7571 is a low-power, single channel, 12-bit
buffered voltage output DAC. Its on-chip precision
output amplifier allows rail-to-rail output swing to be
achieved. The DAC7571 utilizes an I2C compatible
two wire serial interface that operates at clock rates
up to 3.4 Mbps with address support of up to two
DAC7571s on the same data bus.
+2.7-V to +5.5 V-Power Supply
Specified Monotonic by Design
Settling Time: 10 µs to ±0.003%FS
I2C™ Interface up to 3.4 Mbps
On-Chip Output Buffer Amplifier, Rail-to-Rail
Operation
Double-Buffered Input Register
Address Support for up to Two DAC7571s
Small 6 Lead SOT Package
The output voltage range of the DAC is set to VDD
.
The DAC7571 incorporates a power-on-reset circuit
that ensures that the DAC output powers up at zero
volts and remains there until a valid write to the
•
•
•
•
device takes place. The DAC7571 contains
a
power-down feature, accessed via the internal control
register, that reduces the current consumption of the
device to 50 nA at 5 V.
Operation From –40°C to 105°C
APPLICATIONS
The low power consumption of this part in normal
operation makes it ideally suited for portable battery
operated equipment. The power consumption is less
than 0.7 mW at VDD = 5 V reducing to 1 µW in
power-down mode.
•
•
•
•
•
Process Control
Data Acquistion Systems
Closed-Loop Servo Control
PC Peripherals
Portable Instrumentation
The DAC7571 is available in a 6-lead SOT 23
package.
V
DD
GND
Power-On
Reset
Ref (+) REF(-)
12-Bit
DAC
Register
Output
Buffer
V
OUT
DAC
2
I C
Control
Logic
Power Down
Control Logic
Resistor
Network
A0
SCL SDA
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
I2C is a trademark of Philips Corporation.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2003–2004, Texas Instruments Incorporated
DAC7571
www.ti.com
SLAS374A–FEBRUARY 2003–REVISED JANUARY 2004
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
PACKAGE/ORDERING INFORMATION
PACKAGE
DESIG-
NATOR
SPECIFIED TEM-
PERATURE RANGE
PACKAGE
MARKING
ORDERING NUM-
BER
PRODUCT PACKAGE
TRANSPORT MEDIA
DAC7571IDBVT
DAC7571IDBVR
250 Piece Small Tape and Reel
3000 Piece Tape and Reel
DAC7571
SOT23-6
DBV
-40°C to +105°C
D771
PIN DESCRIPTION (SOT23-6)
PIN CONFIGURATIONS
PIN
NAME
DESCRIPTION
(TOP VIEW)
1
VOUT
Analog output voltage from DAC
V
A0
6
5
4
1
2
3
OUT
Ground reference point for all
circuitry on the part
2
GND
GND
SCL
SDA
V
3
4
5
6
VDD
SDA
SCL
A0
Analog Voltage Supply Input
Serial Data Input
DD
(BOTTOM VIEW)
Serial Clock Input
Device Address Select
1
2
3
6
5
4
LOT
TRACE
CODE:
Year (3 = 2003); Month (1–9 = JAN–SEP; A=OCT,
B=NOV, C=DEC); LL– Random code generated
when assembly is requested
Lot Trace Code
ABSOLUTE MAXIMUM RATINGS(1)
UNITS
VDD to GND
-0.3V to +6V
-0.3 V to +VDD + 0.3 V
-0.3 V to +VDD + 0.3 V
-40°C to + 105°C
-65°C to + 150°C
+ 150°C
Digital Input voltage to GND
VOUT to GND
Operating temperature range
Storage temperature range
Junction temperature range (TJ max)
Power dissipation
(TJmax - TA)RΘJA
240°C/W
Thermal impedance, RΘJA
Lead temperature, soldering
Vapor phase (60s)
Infrared (15s)
215°C
220°C
(1) Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. Exposure to absolute
maximum conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
VDD = +2.7 V to +5.5 V; RL = 2 kΩ to GND; CL = 200 pF to GND; all specifications -40°C to +105°C unless otherwise noted.
DAC7571
PARAMETER
CONDITIONS
UNITS
MIN
TYP
MAX
STATIC PERFORMANCE(1)
Resolution
12
Bits
% of FSR
LSB
Relative accuracy
Differential nonlinearity
Zero code error
±0.195
±1
Assured monotonic by design
All zeroes loaded to DAC register
5
20
mV
(1) Linearity calculated using a reduced code range of 48 to 4047; output unloaded.
2
DAC7571
www.ti.com
SLAS374A–FEBRUARY 2003–REVISED JANUARY 2004
ELECTRICAL CHARACTERISTICS (continued)
VDD = +2.7 V to +5.5 V; RL = 2 kΩ to GND; CL = 200 pF to GND; all specifications -40°C to +105°C unless otherwise noted.
DAC7571
PARAMETER
CONDITIONS
UNITS
MIN
TYP
MAX
-1.25
±1.25
Full-scale error
All ones loaded to DAC register
-0.15
% of FSR
% of FSR
Gain error
Zero code error drift
Gain temperature coefficient
OUTPUT CHARACTERISTICS(2)
Output voltage range
Output voltage settling time
Slew rate
±7
±3
µV/°C
ppm of FSR/°C
0
VDD
10
V
µ s
V/µs
pF
1/4 Scale to 3/4 scale change (400H to C00H)
8
1
RL =∞
RL = 2kΩ
470
1000
20
0.5
1
Capacitive load stability
pF
Code change glitch impulse
Digital feedthrough
1 LSB Change around major carry
nV-s
nV-s
Ω
DC output impedance
VDD = +5V
VDD = +3V
50
20
2.5
5
mA
mA
µ s
µ s
Short-circuit current
Coming out of power-down mode, VDD = +5V
Coming out of power-down mode, VDD = +3V
Power-up time
LOGIC INPUTS(3)
Input current
± 1
µ A
V
VINL, Input low voltage
VINH, Input high voltage
Pin capacitance
VDD = +3V
VDD = +5V
0.3×VDD
0.7×VDD
V
3
pF
POWER REQUIREMENTS
VDD
2.7
5.5
V
IDD (normal operation)
VDD = +3.6V to +5.5V
VDD = +2.7V to +3.6V
IDD (all power-down modes)
DAC active and excluding load current
VIH = VDD and VIL = GND
135
115
200
160
µ A
µ A
VIH = VDD and VIL = GND
VDD = +3.6 V to +5.5
V
VIH = VDD and VIL = GND
VIH = VDD and VIL = GND
0.2
1
1
µ A
µ A
VDD = +2.7V to +3.6V
POWER EFFICIENCY
IOUT/IDD
0.05
ILOAD = 2mA, VDD = +5V
93
%
(2) Specified by design and characterization, not production tested.
(3) Specified by design and characterization, not production tested.
3
DAC7571
www.ti.com
SLAS374A–FEBRUARY 2003–REVISED JANUARY 2004
TIMING CHARACTERISTICS
SYMBOL
PARAMETER
TEST CONDITIONS
Standard mode
MIN
TYP
MAX
UNITS
kHz
kHz
MHz
MHz
µs
100
400
3.4
1.7
Fast mode
fSCL
SCL Clock Frequency
High-speed mode, CB - 100pF max
High-Speed mode, CB - 400pF max
Standard mode
4.7
1.3
4.0
600
160
4.7
1.3
160
320
4.0
600
60
Bus Free Time Between a STOP
and START Condition
tBUF
Fast mode
µs
Standard mode
µs
Hold Time (Repeated) START
Condition
tHD; tSTA
Fast mode
ns
High-speed mode
ns
Standard mode
µs
Fast mode
µs
tLOW
LOW Period of the SCL Clock
HIGH Period of the SCL Clock
High-speed mode, CB - 100pF max
High-speed mode, CB - 400pF max
Standard mode
ns
ns
µs
Fast mode
ns
tHIGH
High-speed mode, CB - 100pF max
High-speed mode, CB - 400pF max
Standard mode
ns
120
4.7
600
160
250
100
10
ns
µs
Setup Time for a Repeated
START Condition
tSU; tSTA
Fast mode
ns
High-speed mode
ns
Standard mode
ns
tSU; tDAT
Data Setup Time
Data Hold Time
Fast mode
ns
High-speed mode
ns
Standard mode
0
3.45
0.9
µs
Fast mode
0
µs
tHD; tDAT
High-speed mode, CB - 100pF max
High-speed mode, CB - 400pF max
Standard mode
0
70
ns
0
150
1000
300
40
ns
ns
Fast mode
20 + 0.1CB
ns
tRCL
Rise Time of SCL Signal
High-speed mode, CB - 100pF max
High-speed mode, CB - 400pF max
Standard mode
10
20
ns
80
ns
1000
300
80
ns
Rise Time of SCL Signal After a
Repeated START Condition and
After an Acknowledge BIT
Fast mode
20 + 0.1CB
ns
tRCL1
High-speed mode, CB - 100pF max
High-speed mode, CB - 400pF max
Standard mode
10
20
ns
160
300
300
40
ns
ns
Fast mode
20 + 0.1CB
ns
tFCL
Fall Time of SCL Signal
Rise Time of SDA Signal
Fall Time of SDA Signal
High-speed mode, CB - 100pF max
High-speed mode, CB - 400pF max
Standard mode
10
20
ns
80
ns
1000
300
80
ns
Fast mode
20 + 0.1CB
ns
tRDA
High-speed mode, CB - 100pF max
High-speed mode, CB - 400pF max
Standard mode
10
20
ns
160
300
300
80
ns
ns
Fast mode
20 + 0.1CB
ns
tFDA
High-speed mode, CB - 100pF max
High-speed mode, CB - 400pF max
10
20
ns
160
ns
4
DAC7571
www.ti.com
SLAS374A–FEBRUARY 2003–REVISED JANUARY 2004
TIMING CHARACTERISTICS (continued)
SYMBOL
PARAMETER
TEST CONDITIONS
Standard mode
Fast mode
MIN
4.0
TYP
MAX
UNITS
µs
tSU; tSTO
Setup Time for STOP Condition
600
160
ns
High-speed mode
ns
CB
tSP
Capacitive Load for SDA and SCL
Pulse Width of Spike Suppressed
400
50
pF
Fast mode
High-speed mode
Standard mode
Fast mode
ns
10
ns
Noise Margin at the HIGH Level
for Each Connected Device
(Including Hysteresis)
VNH
0.2VDD
0.1VDD
V
V
High-speed mode
Standard mode
Fast mode
Noise Margin at the LOW Level for
Each Connected Device
VNL
(Including Hysteresis)
High-speed mode
5
DAC7571
www.ti.com
SLAS374A–FEBRUARY 2003–REVISED JANUARY 2004
TYPICAL CHARACTERISTICS: VDD = +5 V
At TA = +25°C, +VDD = +5 V, unless otherwise noted.
LINEARITY ERROR AND
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR
DIFFERENTIAL LINEARITY ERROR
vs
vs
CODE (-40°C)
CODE (+25 ° C )
8
6
8
6
4
2
4
2
0
−2
−4
0
−2
−4
−6
−8
−6
−8
1
1
0.5
0
0.5
0
−0.5
−1
−0.5
−1
0
512
1024
1536 2048 2560
Digital Input Code
3072 3584 4096
0
512
1024
1536 2048 2560 3072
3584 4096
Digital Input Code
Figure 1.
Figure 2.
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR
vs
CODE (+105° C)
TYPICAL TOTAL UNADJUSTED ERROR
8
6
4
2
0
−2
−4
−6
−8
16
8
0
−8
−16
3584 4096
0
512
1024
1536 2048
2560
3072
1
0.5
0
Digital Input Code
−0.5
−1
0
512
1024 1536 2048 2560 3072 3584 4096
Digital Input Code
Figure 3.
Figure 4.
ZERO-SCALE ERROR
vs
FULL-SCALE ERROR
vs
TEMPERATURE
TEMPERATURE
30
20
10
30
20
10
0
0
−10
−10
−20
−30
−20
−30
−50
−30
−10
10
30
50
70
90
110
−50
−30
−10
10
30
50
70
90
110
T − Temperature − _C
T − Temperature − _C
Figure 5.
Figure 6.
6
DAC7571
www.ti.com
SLAS374A–FEBRUARY 2003–REVISED JANUARY 2004
TYPICAL CHARACTERISTICS: VDD = +5 V (continued)
At TA = +25°C, +VDD = +5 V, unless otherwise noted.
IDD HISTOGRAM
SOURCE AND SINK CURRENT CAPABILITY
2500
5
4
3
2
1
0
DAC Loaded with FFFH
2000
1500
1000
500
0
DAC Loaded with 000H
I
− Supply Current − mA
DD
0
5
10
15
ISOURCE/SINK (mA)
Figure 7.
Figure 8.
SUPPLY CURRENT
SUPPLY CURRENT
vs
TEMPERATURE
vs
CODE
500
400
300
300
250
200
150
200
100
0
100
50
0
−50
000
200
600
A00
E00
FFF
H
−30
−10
10
30
50
70
90
110
H
H
H
H
H
CODE
T − Temperature − _C
Figure 9.
Figure 10.
7
DAC7571
www.ti.com
SLAS374A–FEBRUARY 2003–REVISED JANUARY 2004
TYPICAL CHARACTERISTICS: VDD = +5 V (continued)
At TA = +25°C, +VDD = +5 V, unless otherwise noted.
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
POWER-DOWN CURRENT
vs
SUPPLY VOLTAGE
300
100
90
80
70
60
50
40
30
20
10
0
250
200
150
100
50
+105°C
–40°C
0
2.7
+25°C
3.2
3.7
4.2
4.7
5.2
5.7
V
− Supply Voltage − V
DD
2.7
3.2
3.7
4.2
4.7
5.2
5.7
VDD (V)
Figure 11.
Figure 12.
SUPPLY CURRENT
vs
LOGIC INPUT VOLTAGE
FULL-SCALE SETTLING TIME
2500
2000
1500
1000
500
CLK (5V/div)
VOUT (1V/div)
Full-Scale Code Change
000H to FFFH
Output Loaded with
2kΩ and 200pF to GND
0
0
1
2
3
4
5
Time (1µs/div)
VLOGIC (V)
Figure 13.
Figure 14.
8
DAC7571
www.ti.com
SLAS374A–FEBRUARY 2003–REVISED JANUARY 2004
TYPICAL CHARACTERISTICS: VDD = +5 V (continued)
At TA = +25°C, +VDD = +5 V, unless otherwise noted.
FULL-SCALE SETTLING TIME
HALF-SCALE SETTLING TIME
CLK (5V/div)
CLK (5V/div)
VOUT (1V/div)
Half-Scale Code Change
400H to C00H
Full-Scale Code Change
FFFH to 000H
Output Loaded with
2kΩ and 200pF to GND
Output Loaded with
2kΩ and 200pF to GND
VOUT (1V/div)
Time (1µs/div)
Figure 15.
Time (1µs/div)
Figure 16.
POWER-ON RESET TO 0V
HALF-SCALE SETTLING TIME
Loaded with 2kΩ to VDD
.
CLK (5V/div)
Half-Scale Code Change
C00H to 400H
Output Loaded with
2kΩ and 200pF to GND
VDD (1V/div)
VOUT (1V/div)
VOUT (1V/div)
Time (20µs/div)
Time (1µs/div)
Figure 17.
Figure 18.
EXITING POWER-DOWN
(800HLoaded)
CODE CHANGE GLITCH
Loaded with 2kΩ
CLK (5V/div)
and 200pF to GND.
Code Change:
800H to 7FFH.
VOUT (1V/div)
Time (5µs/div)
Time (0.5µs/div)
Figure 19.
Figure 20.
9
DAC7571
www.ti.com
SLAS374A–FEBRUARY 2003–REVISED JANUARY 2004
TYPICAL CHARACTERISTICS: VDD = +2.7V
At TA = +25°C, +VDD = +2.7V, unless otherwise noted.
LINEARITY ERROR AND
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR
DIFFERENTIAL LINEARITY ERROR
vs
vs
CODE (-40 °C)
CODE (+25 °C)
8
6
4
8
6
4
2
2
0
0
−2
−4
−2
−4
−6
−8
−6
−8
1
0.5
0
1
0.5
0
−0.5
−1
−0.5
−1
0
512
1024
1536 2048 2560 3072 3584 4096
0
512
1024 1536 2048 2560 3072 3584 4096
Digital Input Code
Digital Input Code
Figure 21.
Figure 22.
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR
vs
CODE (+105 °C)
ABSOLUTE ERROR
8
6
4
2
0
−2
−4
16
8
−6
−8
0
−8
1
0.5
0
−0.5
−1
−16
512
0
512
1024
1536
2048
2560 3072
3584 4096
0
1024 1536 2048 2560 3072 3584 4096
Digital Input Code
Digital Input Code
Figure 23.
Figure 24.
ZERO-SCALE ERROR
vs
FULL-SCALE ERROR
vs
TEMPERATURE
TEMPERATURE
30
20
10
30
20
10
0
0
−10
−10
−20
−30
−20
−30
−50
−30
−10
10
30
50
70
90
110
−50
−30
−10
10
30
50
70
90
110
T − Temperature − _C
T − Temperature − _C
Figure 25.
Figure 26.
10
DAC7571
www.ti.com
SLAS374A–FEBRUARY 2003–REVISED JANUARY 2004
TYPICAL CHARACTERISTICS: VDD = +2.7V (continued)
At TA = +25°C, +VDD = +2.7V, unless otherwise noted.
IDD HISTOGRAM
SOURCE AND SINK CURRENT CAPABILITY
2500
3
VDD = +3V
2000
1500
1000
DAC Loaded with FFFH
2
1
0
500
0
DAC Loaded with 000H
I
− Supply Current − mA
DD
0
5
10
15
ISOURCE/SINK (mA)
Figure 27.
Figure 28.
SUPPLY CURRENT
SUPPLY CURRENT
vs
9 TEMPERATURE
vs
CODE
300
250
200
150
100
50
500
400
300
200
100
0
0
−50
000 02F 200 400 600 800 A00 C00 E00 FCF FFF
−30
−10
10
30
50
70
90
110
H
H
H
H
H
H
H
H
H
H
I
− Supply Current − mA
H
T − Temperature − _C
DD
Figure 29.
Figure 30.
SUPPLY CURRENT
vs
LOGIC INPUT VOLTAGE
FULL SCALE SETTLING TIME
2500
CLK (2.7V/div)
2000
1500
1000
500
0
Full-Scale Code Change
000H to FFFH
Output Loaded with
2kΩ and 200pF to GND
VOUT (1V/div)
Time (1µs/div)
0
1
2
3
4
5
VLOGIC (V)
Figure 31.
Figure 32.
11
DAC7571
www.ti.com
SLAS374A–FEBRUARY 2003–REVISED JANUARY 2004
TYPICAL CHARACTERISTICS: VDD = +2.7V (continued)
At TA = +25°C, +VDD = +2.7V, unless otherwise noted.
FULL SCALE SETTLING TIME
HALF SCALE SETTLING TIME
CLK (2.7V/div)
CLK (2.7V/div)
Full-Scale Code Change
VOUT (1V/div)
FFFH to 000H
Output Loaded with
2kΩ and 200pF to GND
Half-Scale Code Change
400H to C00H
Output Loaded with
VOUT (1V/div)
2kΩ and 200pF to GND
Time (1µs/div)
Time (1µs/div)
Figure 33.
Figure 34.
HALF SCALE SETTLING TIME
POWER ON RESET 0 V
CLK (2.7V/div)
Half-Scale Code Change
C00H to 400H
Output Loaded with
2kΩ and 200pF to GND
VOUT (1V/div)
Time (20µs/div)
Time (1µs/div)
Figure 35.
Figure 36.
EXITING-POWER DOWN (800HLoaded)
CODE CHANGE GLITCH
Loaded with 2kΩ
CLK (2.7V/div)
and 200pF to GND.
Code Change:
800H to 7FFH.
VOUT (1V/div)
Time (5µs/div)
Time (0.5µs/div)
Figure 37.
Figure 38.
12
DAC7571
www.ti.com
SLAS374A–FEBRUARY 2003–REVISED JANUARY 2004
THEORY OF OPERATION
D/A SECTION
The architecture of the DAC7571 consists of a string DAC followed by an output buffer amplifier. Figure 39
shows a block diagram of the DAC architecture.
V
DD
REF (+)
Resistor
String
DAC Register
V
OUT
Output
REF (-)
Amplifier
GND
Figure 39. R-String DAC Architecture
The input coding to the DAC7571 is unsigned binary, which gives the ideal output voltage as:
D
4096
V
+ V
DD
OUT
where D = decimal equivalent of the binary code that is loaded to the DAC register; it can range from 0 to 4095.
RESISTOR STRING
The resistor string section is shown in Figure 40. It is simply a string of resistors, each of value R. The code
loaded into the DAC register determines at which node on the string the voltage is tapped off to be fed into the
output amplifier by closing one of the switches connecting the string to the amplifier. It is ensured monotonic
because it is a string of resistors. The negative tap of the resistor string is tied to GND. The positive tap of the
resistor string is tied to VDD
.
V
DD
R
To Output
Amplifier
R
R
R
GND
Figure 40. Resistor String
13
DAC7571
www.ti.com
SLAS374A–FEBRUARY 2003–REVISED JANUARY 2004
THEORY OF OPERATION (continued)
OUTPUT AMPLIFIER
The output buffer amplifier is capable of generating rail-to-rail voltages on its output which gives an output range
of 0 V to VDD. It is capable of driving a load of 2kΩ in parallel with 1000 pF to GND. The source and sink
capabilities of the output amplifier can be seen in the typical characteristics. The slew rate is 1V/µs with a
half-scale settling time of 8 µs with the output unloaded.
I2C Interface
The DAC7571 uses an I2C interface as defined by Philips Semiconductor to receive data in slave mode (see
I2C-Bus Specification, Version 2.1, January 2000). The DAC7571 supports the following data transfer modes,
described in the I2C-Bus Specification: Standard Mode (100 kbit/s), Fast Mode (400 kbit/s) and High-Speed
Mode (3.4 Mbit/s). Ten-bit addressing and general call addres are not supported.
For simplicity, standard mode and fast mode are referred to as F/S-mode and high-speed mode is referred tg as
HS-mode.
The 2-wire I2C serial bus protocol operates as follows:
•
The Master initiates data transfer by establishing a Start condition. The Start condition is defined when a
high-to-low transition occurs on the SDA line while SCL is high, as shown in Figure 41. The byte following
the start condition is the address byte consisting of the 7-bit slave address followed by the W bit.
SDA
SCL
SDA
SCL
S
P
Start
Stop
Condition
Condition
Figure 41. START and STOP Conditions
•
The addressed Slave responds by pulling the SDA pin low during the ninth clock pulse, termed the
Acknowledge bit (see Figure 42). At this stage all other devices on the bus remain idle while the selected
device waits for data to be written to its shift register.
Data Output
by Transmitter
Not Acknowledge
Data Output
by Receiver
Acknowledge
SCL From
Master
1
2
8
9
S
Clock Pulse for
START
Acknowledgement
Condition
Figure 42. Acknowledge on the I2C Bus
•
Data is transmitted over the serial bus in sequences of nine clock cycles (8 data bits followed by an
acknowledge bit. The transitions on the SDA line must occur during the low period of SCL and remain stable
during the high period of SCL (see Figure 43).
14
DAC7571
www.ti.com
SLAS374A–FEBRUARY 2003–REVISED JANUARY 2004
THEORY OF OPERATION (continued)
SDA
SCL
Data Line
Change of Data Allowed
Stable;
Data Valid
Figure 43. Bit Transfer on the I2C Bus
•
When all data bits have been written, a Stop condition is established (see Figure 44). In writing to the
DAC7571, the master must pull the SDA line high during the tenth clock pulse to establish a Stop condition.
Recognize START or
REPEATED START
Condition
Recognize STOP or
REPEATED START
Condition
Generate ACKNOWLEDGE
Signal
P
SDA
MSB
Acknowledgement
Signal From Slave
Sr
Address
R/W
SCL
1
2
7
8
9
1
2
3 - 8
9
S
or
Sr
Sr
or
P
ACK
ACK
Clock Line Held Low While
Interrupts are Serviced
START or
Repeated START
Condition
STOP or
Repeated START
Condition
Figure 44. Bus Protocol
15
DAC7571
www.ti.com
SLAS374A–FEBRUARY 2003–REVISED JANUARY 2004
THEORY OF OPERATION (continued)
Standard-and Fast-Mode:
S
SLAVE ADDRESS R/W
A
Ctrl/MS-Byte
A
LS-Byte A/A
P
Data Transferred
(n* Words + Acknowledge)
Word = 16 Bit
”0” (write)
2
From Master to DAC7571
From DAC7571 to Master
DAC7571 I C-SLAVE ADDRESS:
MSB
LSB
1
0
0
1
1
0
A0 R/W
A = Acknowledge (SDA LOW)
A = Not Acknowledge (SDA HIGH)
S = START Condition
‘0’ = Write to DAC7571
Factory Preset
‘1’ = Read from DAC7571
2
Sr = Repeated START Condition
P = STOP Condition
A0 = I C Address Pin
High-Speed-Mode (HS-Mode):
F/S-Mode
HS-Mode
Ctrl/MS-Byte
F/S-Mode
S
HS-Master Code
A
Sr Slave Address R/W
A
A
LS-Byte A/A
P
Data Transferred
(n* Words + Acknowledge)
Word = 16 Bit
”0” (write)
HS-Mode Continues
Sr Slave Address
HS-Mode Master Code:
MSB
LSB
0
0
0
0
1
X
X
R/W
Ctrl/MS-Byte:
LS-Byte:
MSB
LSB
D8
MSB
LSB
D0
0
0
PD1 PD2 D11 D10 D9
D7
D6
D5
D4
D3
D2
D1
D11 – D0 = Data Bits
Figure 45. Master Transmitter Addressing DAC7571 as a Slave Receiver With a 7-Bit Address
ADDRESS BYTE
MSB
R/W
1
0
0
1
1
0
A0
0
The address byte is the first byte received by the DAC7571 following the START condition from the master
device. The first five bits (MSBs) of the slave address are factory preset to 100110. The next bit of the address
byte is the device select bit, A0. In order for DAC7571 to respond, the logic state of address bit A0 should match
the logic state of address pin A0. A maximum of two devices with the same preset code can therefore be
connected on the same bus at one time. The A0 Address Input can be connected to VDD or digital ground, or can
be actively driven by TTL or CMOS logic levels. The device address is set by the state of the A0 pin upon
power-up of the DAC7571. The last bit of the address byte (R/W) should always be zero. Following the START
condition, the DAC7571 monitors the SDA bus, checking the device type identifier being transmitted. Upon
receiving the 100110 code, the appropriate device select bit and the R/W bit, the DAC7571 outputs an
acknowledge signal on the SDA line. Upon receipt of a broadcast address 10010000, the DAC7571 responds
regardless of the state of the A0 pin.
16
DAC7571
www.ti.com
SLAS374A–FEBRUARY 2003–REVISED JANUARY 2004
MASTER TRANSMITTER WRITING TO A SLAVE RECEIVER (DAC7571) IN STANDARD/FAST
MODES
I2C protocol starts when the bus is dile, that is, when SDA and SCL lines are stable high. The master then pulls
the SDA line low while SCL is still high indicting that serial data transfer has started. This is called a start
condition, and can only be asserted by the master. After the start conditioin, the master generates the serial
clock and puts out an address byte. While generating the bit stream, the master ensures the timing for valid data.
For each valid I2C bit, the SDA line should remain stable during the entire high period of the SCL line. The
address byte consists of 7 address bits (1001 100, assuming A0=0) and a direction bit (R/W=0). After sending
the address byte, the master generates a ninth SCL pulse and monitors the state of the SDA line during the high
period of this ninth clock cycle.
The SDA line being pulled low by a receiver during the high period of this 9th clock cylce is called an
acknowledge signal. If the master receives an acknowledge signal, it knows that a DAC7571 successfully
matched the address which the master sent. Upon the receipt of this acknowledge, the master knows that the
communication link with a DAC7571 has been established and more data can be sent. The master continues by
sending a Control/MS-byte, which sets DAC7571 operation mode and specifies the first 4 MSBs of data. After
sending the Control/MS-byte, the master expects an acknowledge signal from the DAC7571. Upon the receipt of
the acknowledge, the master sends an LS-byte that represents the 8 least significant bits of DAC7571's 12-bit
conversion data. After receiving the LS-byte, the DAC7571 sends an acknowledge. At the falling edge of the
acknowledge signal, following the LS-byte, the DAC7571 performs a digital to analog conversion. For further
DAC updates, the master can keep repeating Control/MS-byte and LS-byte sequences expecting an
acknowledge after each byte. After the required number of digital to analog conversions is complete, the master
can break the communication link with the DAC7571 by pulling the SDA line from low to high while SCL line is
high. This is called a stop condition . A stop condition brings the bus back to idle (SDA and SCL both high). A
stop condition indicates that communication with the DAC7571 has ended. All devices on the bus, including the
DAC7571, waits for a new start condition followed by a mtaching address byte. DAC7571 stays in a programmed
state until the receipt of a stop condition.
Table 1. Write Sequence in Standard/Fast Modes
Transmitter
MSB
6
5
4
3
2
1
LSB
Comment
Master
Start
Begin Sequence(1)
Write Addressing (LSB=0, R/W =
0)
Master
1
0
0
1
1
0
A0
0
DAC7571
Master
DAC7571 Acknowledges
PD0 D11
DAC7571 Acknowledges
D4 D3
0
0
PD1
D5
D10
D2
D9
D1
D8
D0
Writing Control/MS-Byte
Writing LS-Byte
Done
DAC7571
Master
D7
D6
DAC7571
Master
DAC7571 Acknowledges
Stop or Repeated Start(2)
(1) Once DAC7571 is addressed, high-byte-low-byte sequences can repeat until a stop condition is received.
(2) Use repeated start to secure bus operation and loop back to the stage of write addressing for next Write.
POWER-ON RESET
The DAC7571 contains a power-on reset circuit that controls the output voltage during power-up. On power-up,
the DAC register is filled with zeros and the output voltage is 0 V. It remains at a zero-code output until a valid
write sequence is made to the DAC. This is useful in applications where it is important to know the state of the
DAC output while it is in the process of powering up.
POWER-DOWN MODES
The DAC7571 contains four separate modes of operation. These modes are programmable via two bits (PD1
and PD0). Table 2 shows how the state of these bits correspond to the mode of operation.
17
DAC7571
www.ti.com
SLAS374A–FEBRUARY 2003–REVISED JANUARY 2004
Table 2. Modes of Operation for the DAC7571
PD1
PD0
OPERATING MODE
Normal Operation
0
0
1
1
0
1
0
1
1kΩ to AGND, PWD
100kΩ to AGND, PWD
High Impedance, PWD
When both bits are set to 0, the device works normally with normal power consumption of 150 µA at 5V.
However, for the three power-down modes, the supply current falls to 200 nA at 5V (50 nA at 3 V). Not only does
the supply current fall but the output stage is also internally switched from the output of the amplifier to a resistor
network of known values. This has the advantage that the output impedance of the device is known while in
power-down mode. There are three different options: The output is connected internally to AGND through a 1 kΩ
resistor, a 100 kΩ resistor, or it is left open-circuited (high impedance). The output stage is illustrated in
Figure 46.
Amplifier
Resistor
V
OUT
String DAC
Powerdown
Circuitry
Resistor
Network
Figure 46. Output Stage During Power-Down
All linear circuitry is shut down when the power-down mode is activated. However, the contents of the DAC
register are unaffected when in power-down. The time required to exit power down is typically 2.5 µs for AVDD
5 V and 5 µs for AVDD = 3V. See the Typical Characteristics for more information.
=
CURRENT CONSUMPTION
The DAC7571 typically consumes 150 µA at VDD = 5 V and 120 µA at VDD = 3 V. Additional current consumption
can occur due to the digital inputs if VIH << VDD. For most efficient power operation, CMOS logic levels are
recommended at the digital inputs to the DAC. In power-down mode, typical current consumption is 200 nA. Ten
to 20 ms after a power-down command is issued, the power-down current typically drops below 10 mA.
DRIVING RESISTIVE AND CAPACITIVE LOADS
The DAC7571 output stage is capable of driving loads of up to 1000 pF while remaining stable. Within the offset
and gain error margins, the DAC7571 can operate rail-to-rail when driving a capacitive load. Resistive loads of 2
kΩ can be driven by the DAC7571 while achieving a typical load regulation of 1%. As the load resistance drops
below 2 kΩ, the load regulation error increases. When the outputs of the DAC are driven to the positive rail under
resistive loading, the PMOS transistor of each Class-AB output stage can enter into the linear region. When this
occurs, the added IR voltage drop deteriorates the linearity performance of the DAC. This may occur within
approximately the top 20 mV of the DAC's digital input-to-voltage output transfer characteristic.
OUTPUT VOLTAGE STABILITY
The DAC7571 exhibits excellent temperature stability of 5 ppm/°C typical output voltage drift over the specified
temperature range of the device. This enables the output voltage to stay within a ±25 µV window for a ±1°C
ambient temperature change. Good power-supply rejection ratio (PSRR) performance reduces supply noise
present on VDD from appearing at the outputs to well below 10 µV-s. Combined with good dc noise performance
and true 12-bit differential linearity, the DAC7571 becomes a perfect choice for closed-loop control applications.
18
DAC7571
www.ti.com
SLAS374A–FEBRUARY 2003–REVISED JANUARY 2004
APPLICATIONS
USING REF02 AS A POWER SUPPLY FOR THE DAC7571
Due to the extremely low supply current required by the DAC7571, a possible configuration is to use a REF02
+5V precision voltage reference to supply the required voltage to the DAC7571's supply input as well as the
reference input, as shown in Figure 47. This is especially useful if the power supply is quite noisy or if the system
supply voltages are at some value other than 5V. The REF02 will output a steady supply voltage for the
DAC7571. If the REF02 is used, the current it needs to supply to the DAC7571 is 150 µA typical and 200 µA max
for VDD = 5V. When a DAC output is loaded, the REF02 also needs to supply the current to the load. The total
typical current required (with a 5 mW load on a given DAC output) is: 135 µA + (5 mW/5 V) = 1.14 mA.
The load regulation of the REF02 is typically (0.005%×VDD)/mA, which results in an error of 285 mV for the 1.14
mA current drawn from it. This corresponds to a 0.2 LSB error for a 0 V to 5 V output range.
15 V
5 V
REF02
1.14 mA
A0
SCL
SDA
V
OUT
= 0 V to 5 V
2
I C
DAC7571
Interface
Figure 47. REF02 as Power Supply to DAC7571
LAYOUT
A precision analog component requires careful layout, adequate bypassing, and clean, well-regulated power
supplies.
The power applied to VDD should be well regulated and low noise. Switching power supplies and DC/DC
converters will often have high-frequency glitches or spikes riding on the output voltage. In addition, digital
components can create similar high-frequency spikes as their internal logic switches states. This noise can easily
couple into the DAC output voltage through various paths between the power connections and analog output.
As with the GND connection, VDD should be connected to a +5V power supply plane or trace that is separate
from the connection for digital logic until they are connected at the power entry point. In addition, the 1 µF to 10
µF and 0.1 µF bypass capacitors are strongly recommended. In some situations, additional bypassing may be
required, such as a 100µF electrolytic capacitor or even a Pi filter made up of inductors and capacitors—all
designed to essentially low-pass filter the +5V supply, removing the high-frequency noise.
19
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Audio
Amplifiers
amplifier.ti.com
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
Digital Control
Military
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/military
Interface
Logic
interface.ti.com
logic.ti.com
Power Mgmt
Microcontrollers
power.ti.com
Optical Networking
Security
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
microcontroller.ti.com
Telephony
Video & Imaging
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright 2004, Texas Instruments Incorporated
相关型号：
DAC7574IDGSRG4
QUAD, 12-BIT, LOW-POWER, VOLTAGE OUTPUT, I2C INTERFACE DIGITAL-TO-ANALOG CONVERTER
TI
DAC7578
8-/10-/12-Bit, Octal-Channel, Ultra-Low Glitch, Voltage Output, Two-Wire Interface Digital-to-Analog Converters
TI
DAC7578SPW
8-/10-/12-Bit, Octal-Channel, Ultra-Low Glitch, Voltage Output, Two-Wire Interface Digital-to-Analog Converters
TI
DAC7578SPWR
8-/10-/12-Bit, Octal-Channel, Ultra-Low Glitch, Voltage Output, Two-Wire Interface Digital-to-Analog Converters
TI
DAC7578SRGER
8-/10-/12-Bit, Octal-Channel, Ultra-Low Glitch, Voltage Output, Two-Wire Interface Digital-to-Analog Converters
TI
©2020 ICPDF网 联系我们和版权申明