DS92LV040A [TI]
4 通道总线 LVDS 收发器;型号: | DS92LV040A |
厂家: | TEXAS INSTRUMENTS |
描述: | 4 通道总线 LVDS 收发器 |
文件: | 总25页 (文件大小:997K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Support &
Community
Product
Folder
Order
Now
Tools &
Software
Technical
Documents
DS92LV040A
ZHCSHA7E –JANUARY 2001–REVISED JANUARY 2018
DS92LV040A 4 通道总线 LVDS 收发器
1 特性
驱动器可将 3 V LVTTL 电平(单端)转换为差动总线
1
LVDS (BLVDS) 输出电平。该功能可以在支持高速运
行的同时将功耗降至最低并降低 EMI。此外,该差动
信令可提供大于 ±1 V 的共模噪声抑制。
•
•
总线 LVDS 信令
传播延迟:驱动器最大值为 2.3 ns,接收器最大值
为 3.2 ns
•
•
低功耗 CMOS 设计
接收器阈值小于 +0/70 mV。接收器可将差动总线
LVDS 转换为标准 (LVTTL/LVCMOS) 电平。(请参阅
应用信息 部分了解详细信息。)
驱动器 100% 转换时间典型值为 1 ns,接收器典型
值为 1.3 ns
•
•
高信号传输速率功能(155 Mbps 以上)
Device Information(1)
VID 0.1 V 至 2.3 V 共模范围 = 200 mV
70 mV 接收器灵敏度
PART NUMBER
PACKAGE
BODY SIZE (NOM)
•
•
•
•
•
DS92LV040A
WQFN (44)
7.00mm x 7.00mm
支持打开和终止端口引脚故障保护
3.3 V 运行电压
(1) 要了解所有可用封装,请参阅数据表末尾的可订购产品附录。
简化功能图
无毛刺加电/断电(已禁用驱动器和接收器)
每总线 LVDS 负载的轻型总线负载(典型值 5
pF)
DO1+/RI1+
DIN1
•
•
•
平衡输出阻抗
DO1-/RI1-
44 引脚 WQFN 封装中提供的产品
DE1
RO1
断电时高阻抗总线引脚
(VCC = 0 V)
RE1
DO2+/RI2+
DIN2
2 应用
DO2-/RI2-
专为双终端设计 应用
RO2
3 说明
DO3+/RI3+
DO3-/RI3-
DS92LV040A 属于总线 LVDS 收发器系列产品,专用
于高速、低功耗背板或电缆接口。器件由 3.3 V 单电源
供电运行,并包括四个差动线路驱动器和四个接收器。
要将总线负载降至最低,驱动器输出端和接收器输入端
需进行内部连接。此外,该器件还具备 一只 直通式外
引脚,以支持短接线柱在其引脚和连接器之间轻松实现
PCB 路由。
DIN3
DE2
RO3
RE2
DO4+/RI4+
DIN4
DO4-/RI4-
RO4
Copyright © 2018, Texas Instruments Incorporated
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
English Data Sheet: SNOS521
DS92LV040A
ZHCSHA7E –JANUARY 2001–REVISED JANUARY 2018
www.ti.com.cn
目录
8.3 Feature Description................................................... 9
8.4 Device Functional Modes........................................ 10
Application and Implementation ........................ 11
9.1 Application Information............................................ 11
9.2 Typical Application ................................................. 11
1
2
3
4
5
6
特性.......................................................................... 1
应用.......................................................................... 1
说明.......................................................................... 1
修订历史记录 ........................................................... 2
Pin Configuration and Functions......................... 3
Specifications......................................................... 4
6.1 Absolute Maximum Ratings ...................................... 4
6.2 ESD Ratings.............................................................. 4
6.3 Recommended Operating Conditions....................... 4
6.4 Thermal Information.................................................. 4
6.5 DC Electrical Characteristics .................................... 5
6.6 AC Electrical Characteristics..................................... 6
Parameter Measurement Information .................. 6
7.1 Test Circuits and Timing Waveforms........................ 6
Detailed Description .............................................. 9
8.1 Overview ................................................................... 9
8.2 Functional Block Diagram ......................................... 9
9
10 Power Supply Recommendations ..................... 13
11 Layout................................................................... 14
11.1 Layout Guidelines ................................................. 14
11.2 Layout Example .................................................... 17
12 器件和文档支持 ..................................................... 19
12.1 Documentation Support ........................................ 19
12.2 Receiving Notification of Documentation Updates 19
12.3 Community Resources.......................................... 19
12.4 商标....................................................................... 19
12.5 静电放电警告......................................................... 19
12.6 Glossary................................................................ 19
13 机械、封装和可订购信息....................................... 19
7
8
4 修订历史记录
注:之前版本的页码可能与当前版本有所不同。
Changes from Revision D (April 2013) to Revision E
Page
•
添加了器件信息表、ESD 额定值表、特性 说明 部分、器件功能模式、应用和实施 部分、电源相关建议 部分、布局
部分、器件和文档支持 部分以及机械、封装和可订购信息 部分............................................................................................. 1
•
•
Added "Driver Short Circuit Current Duration" to the Absolute Maximum Ratings ................................................................ 4
Deleted Note 4: "Only one output at a time should be shorted..." from the DC Electrical Characteristics table.................... 5
Changes from Revision C (April 2013) to Revision D
Page
•
Changed layout of National Data Sheet to TI format ............................................................................................................. 3
2
Copyright © 2001–2018, Texas Instruments Incorporated
DS92LV040A
www.ti.com.cn
ZHCSHA7E –JANUARY 2001–REVISED JANUARY 2018
5 Pin Configuration and Functions
NJN Package
WQFN (44 Pin)
Top View
34
33
32
31
30
29
28
27
26
25
24
23
NC
NC
NC
1
NC
2
NC
VCC
GND
RE34
VCC
AVCC
DE34
AGND
AVCC
NC
3
GND
VCC
RE12
GND
AVCC
DE12
AGND
NC
4
5
6
7
8
9
10
11
12
NC
NC
Not to scale
Pin Functions
PIN NAME
PIN #
INPUT/
DESCRIPTIONS
OUTPUT
DO+/RI+
DO−/RI−
DIN
14, 16, 19, 21
13, 15, 18, 20
35, 37, 40, 42
36, 38, 41, 43
I/O
I/O
I
True Bus LVDS Driver Outputs and Receiver Inputs.
Complimentary Bus LVDS Driver Outputs and Receiver Inputs.
LVTTL Driver Input. No pull up or pull down is attached to this pin
LVTTL Receiver Output.
RO
O
Receiver Enable LVTTL Input (Active Low). This pin, when low, configures receiver outputs, RO1 and
RO2 active. When this pin is high, RO1 and RO2 are TRI-STATE. If this pin is floating, a weak current
source to VCC causes RO1 and RO2 to be TRI-STATE
RE12
RE34
29
5
I
I
Receiver Enable LVTTL Input (Active Low). This pin, when low, configures receiver outputs, RO3 and
RO4 active. When this pin is high, RO3 and RO4 are TRI-STATE. If this pin is floating, a weak current
source to VCC causes RO3 and RO4 to be TRI-STATE
Driver Enable LVTTL Input (Active High). This pin, when high, configures driver outputs, DO1+/RIN1+,
DO1−/RIN1− and DO2+/RIN2+, DO2−/RIN2− active. When this pin is low, driver outputs 1 and 2 are
TRI-STATE. If this pin is floating, a weak current source to VCC causes driver outputs 1 and 2 to be
active
DE12
DE34
26
8
I
I
Driver Enable LVTTL Input (Active High). This pin, when high, configures driver outputs, DO3+/RIN3+,
DO3−/RIN3− and DO4+/RIN4+, DO4−/RIN4− active. When this pin is low, driver outputs 3 and 4 are
TRI-STATE. If this pin is floating, a weak current source to VCC causes driver outputs 3 and 4 to be
active
GND
VCC
4, 28, 31, 39
3, 6, 30
Ground
Power
Ground
Power
Ground for digital circuitry (must connect to GND on PC board). These pins connected internally.
VCC for digital circuitry (must connect to VCC on PC board). These pins connected internally.
Ground for analog circuitry (must connect to GND on PC board). These pins connected internally.
Analog VCC (must connect to VCC on PC board). These pins connected internally.
AGND
AVCC
9, 17, 25
7, 10, 22, 27
1, 2, 11, 12, 23, 24,
32, 33, 34, 44
NC
N/A
Reserved for future use, leave open circuit.
Must connect to GND plane through vias to achieve the theta ja specified under Absolute Maximum
Ratings. The DAP (die attach pad) is the heat transfer material that is centered on the bottom of the
WQFN package. Refer to application note AN-1187 () for attachment details.
DAP
GND
Copyright © 2001–2018, Texas Instruments Incorporated
3
DS92LV040A
ZHCSHA7E –JANUARY 2001–REVISED JANUARY 2018
www.ti.com.cn
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1)(2)ccr(3)
MIN
MAX
4
UNIT
Supply Voltage, VCC
V
V
V
Enable Input Voltage (DE, RE)
−0.3
−0.3
VCC +0.3 V
VCC +0.3 V
Driver Input Voltage (DIN
)
Driver Short Circuit Current Duration
Continuous
Receiver Output Voltage ( ROUT
Bus Pin Voltage (DO±/RI±)
Storage temperature, Tstg
)
−0.3
−0.3
−65
VCC +0.3 V
3.9
V
V
150
°C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
(3) All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to ground unless
otherwise specified except VOD, ΔVOD and VID
.
6.2 ESD Ratings
VALUE
UNIT
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(3)
±2000
V(ESD)
Electrostatic discharge(1)(2)
V
Charged-device model (CDM), per JEDEC specification JESD22-
C101(4)
±1000
(1) All typicals are given for VCC = +3.3 V and TA = +25°C, unless otherwise stated.
(2) ESD Rating: HBM (1.5 kΩ, 100 pF) > 4 kV EIAJ (0 Ω, 200 pF) > 250.
(3) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(4) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
3
NOM
MAX
3.6
2.4
85
1
UNIT
V
VCC
Supply Voltage
Receiver Input Voltage
Ambient Free Air Temperature
0
V
TA
−40
°C
Data
ns/V
ns/V
Slowest Input Edge Rate, Δt/ΔV
(20% to 80%)(1)
Control
3
(1) Generator waveforms for all tests unless otherwise specified: f = 25 MHz, ZO = 50 Ω, tr, tf = <1 ns (0%–100%). To ensure fastest
propagation delay and minimum skew, data input edge rates should be equal to or faster than 1 ns/V; control signals equal to or faster
than 3 ns/V. In general, the faster the input edge rate, the better the AC performance.
6.4 Thermal Information
DS92LV040A
THERMAL METRIC(1)
NJN (WQFN)
44 PINS
25.8
UNIT
(2)
RθJA
Junction-to-ambient thermal resistance
°C/W
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
25.5
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
(2) Package must be mounted to pc board in accordance with AN-1187 (SNOA401) to achieve thermals.
4
Copyright © 2001–2018, Texas Instruments Incorporated
DS92LV040A
www.ti.com.cn
ZHCSHA7E –JANUARY 2001–REVISED JANUARY 2018
6.5 DC Electrical Characteristics(1)
Over recommended operating supply voltage and temperature ranges unless otherwise specified.(2)(3)
PARAMETER
TEST CONDITIONS
PIN
MIN
TYP
300
5
MAX
460
27
UNIT
mV
mV
V
VOD
Output Differential Voltage
VOD Magnitude Change
Offset Voltage
200
ΔVOD
VOS
RL = 27Ω, 图 1
1.1
1.3
5
1.5
ΔVOS
VOHD
VOLD
Offset Magnitude Change
Driver Output High Voltage
Driver Output Low Voltage
DO+/RI+,
DO−/RI−
10
mV
V
RL = 27Ω
RL = 27Ω
1.4
1.1
1.65
0.95
V
Driver Output Short Circuit
Current
VOD = 0V, DE = VCC, Driver outputs shorted
together
IOSD
|30|
| 45|
mA
VID = +300 mV
V
CC−0.2
CC−0.2
V
V
Inputs Open
V
VOHR
Receiver Voltage Output High(4)
IOH = −4 mA
Inputs Terminated,
RL = 27Ω
VCC−0.2
V
ROUT
VOLR
IOD
Receiver Voltage Output Low
IOL = 4.0 mA, VID = −300 mV
VID = 300mV, VOUT = VCC−1.0V
VID = −300mV, VOUT = 1.0V
0.05
|33|
|36|
−40
−40
0.100
V
−50
mA
mA
mV
mV
Receiver Output Dynamic Current
60
0
VTH
VTL
Input Threshold High(5)
Input Threshold Low(5)
DE = 0V, Over common mode range
−70
|VID|/2
2.4 −
|VID|/2
VCMR
Receiver Common Mode Range
DO+/RI+,
DO−/RI−
V
DE = 0V, RE = 2.4V,
VIN = +2.4V or 0V
−20
±1
±1
+20
µA
IIN
Input Current
VCC = 0V, VIN = +2.4V or 0V
−20
2.0
+20
VCC
0.8
µA
V
VIH
VIL
IIH
Minimum Input High Voltage
Maximum Input Low Voltage
Input High Current
GND
−20
−20
−1.5
V
VIN = VCC or 2.4V
VIN = GND or 0.4V
ICLAMP = −18 mA
DIN, DE, RE
±2.5
±2.5
−0.8
+20
+20
µA
µA
V
IIL
Input Low Current
VCL
Input Diode Clamp Voltage
Power Supply Current Drivers
Enabled, Receivers Disabled
No Load, DE = RE = VCC
DIN = VCC or GND
,
ICCD
ICCR
ICCZ
20
27
28
40
40
40
mA
mA
mA
Power Supply Current Drivers
Disabled, Receivers Enabled
DE = RE = 0V, VID = ±300mV
VCC
Power Supply Current, Drivers
and Receivers TRI-STATE
DE = 0V; RE = VCC
,
DIN = VCC or GND
DE = VCC; RE = 0V,
DIN = VCC or GND,
RL = 27Ω
Power Supply Current, Drivers
and Receivers Enabled
ICC
70
100
+20
mA
µA
VCC = 0V or OPEN,
DIN, DE, RE = 0V or OPEN,
VAPPLIED = 3.6V (Port Pins)
DO+/RI+,
DO−/RI−
IOFF
Power Off Leakage Current
−20
DO+/RI+,
DO−/RI−
COUTPUT
cOUTPUT
Capacitance at Bus Pins
Capacitance at ROUT
5
5
pF
pF
ROUT
(1) The DS92LV040A functions within datasheet specification when a resistive load is applied to the driver outputs.
(2) All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to ground unless
otherwise specified except VOD, ΔVOD and VID
.
(3) All typicals are given for VCC = +3.3 V and TA = +25°C, unless otherwise stated.
(4) VOH fail-safe terminated test performed with 27 Ω connected between RI+ and RI− inputs. No external voltage is applied.
(5) Propagation delays, transition times, and receiver threshold are ensured by design and characterization.
Copyright © 2001–2018, Texas Instruments Incorporated
5
DS92LV040A
ZHCSHA7E –JANUARY 2001–REVISED JANUARY 2018
www.ti.com.cn
6.6 AC Electrical Characteristics
Over recommended operating supply voltage and temperature ranges unless otherwise specified.(1)
PARAMETER
TEST CONDITIONS(2)
MIN
TYP
MAX
UNIT
DIFFERENTIAL DRIVER TIMING REQUIREMENTS
tPHLD
tPLHD
tSKD1
tCCSK
tTLH
Differential Prop. Delay High to Low(3)
Differential Prop. Delay Low to High(3)
Differential Skew |tPHLD–tPLHD| (duty cycle)(4)
Channel to Channel Skew (all 4 channels)(3)(5)
Transition Time Low to High (20% to 80%)
Transition Time High to Low (80% to 20%)
Disable Time High to Z
1
1
1.5
1.5
80
220
0.75
0.75
5
2.3
2.3
160
400
1.3
1.3
10
ns
ns
ps
ps
ns
ns
ns
ns
ns
ns
(3)
RL = 27Ω,
图 2, 图 3,
CL = 10 pF
0.4
0.4
tTHL
tPHZ
RL = 27Ω,
图 4, 图 5,
CL = 10 pF
tPLZ
Disable Time Low to Z
5
10
tPZH
Enable Time Z to High
5
10
tPZL
Enable Time Z to Low
5
10
fMAXD
Ensured operation per data sheet up to the Min. Duty Cycle
85
125
MHz
45/55%,Transition time ≤ 25% of period(3)
DIFFERENTIAL RECEIVER TIMING REQUIREMENTS
tPHLDR
tPLHDR
tSDK1R
tCCSKR
tTLHR
tTHLR
tPHZ
Differential Prop. Delay High to Low(3)
Differential Prop Delay Low to High(3)
Differential Skew |tPHLD–tPLHD| (duty cycle)(4)(3)
Channel to Channel Skew (all 4 channels)(3)(5)
Transition Time Low to High (10% to 90%)(3)
Transition Time High to Low (90% to 10%)(3)
Disable Time High to Z
1.6
1.6
2.4
2.4
85
140
1.25
1.03
3
3.2
3.2
160
300
2
ns
ns
ps
ps
ns
ns
ns
ns
ns
ns
图 6, 图 7,
CL = 15 pF
0.85
0.85
2
10
10
10
10
RL = 500Ω,
图 8, 图 9,
CL = 15 pF
tPLZ
Disable Time Low to Z
3
tPZH
Enable Time Z to High
3
tPZL
Enable Time Z to Low
3
Ensured operation per data sheet up to the Min. Duty Cycle
fMAXR
85
125
45/55%,Transition time ≤ 25% of period(3)
MHz
(1) Generator waveforms for all tests unless otherwise specified: f = 25 MHz, ZO = 50 Ω, tr, tf = <1 ns (0%–100%). To ensure fastest
propagation delay and minimum skew, data input edge rates should be equal to or faster than 1 ns/V; control signals equal to or faster
than 3ns/V. In general, the faster the input edge rate, the better the AC performance.
(2) CL includes probe and fixture capacitance.
(3) Propagation delays, transition times, and receiver threshold are ensured by design and characterization.
(4) tSKD1 |tPHLD–tPLHD| is the worst case pulse skew (measure of duty cycle) over recommended operation conditions.
(5) Chip to Chip skew is the difference in differential propagation delay between any channels of any devices, either edge.
7 Parameter Measurement Information
7.1 Test Circuits and Timing Waveforms
图 1. Differential Driver DC Test Circuit
6
版权 © 2001–2018, Texas Instruments Incorporated
DS92LV040A
www.ti.com.cn
ZHCSHA7E –JANUARY 2001–REVISED JANUARY 2018
Test Circuits and Timing Waveforms (接下页)
图 2. Differential Driver Propagation Delay and Transition Time Test Circuit
图 3. Differential Driver Propagation Delay and Transition Time Waveforms
图 4. Driver TRI-STATE Delay Test Circuit
图 5. Driver TRI-STATE Delay Waveforms
版权 © 2001–2018, Texas Instruments Incorporated
7
DS92LV040A
ZHCSHA7E –JANUARY 2001–REVISED JANUARY 2018
www.ti.com.cn
Test Circuits and Timing Waveforms (接下页)
图 6. Receiver Propagation Delay and Transition Time Test Circuit
图 7. Receiver Propagation Delay and Transition Time Waveforms
图 8. Receiver TRI-STATE Delay Test Circuit
图 9. Receiver TRI-STATE Delay Waveforms
8
版权 © 2001–2018, Texas Instruments Incorporated
DS92LV040A
www.ti.com.cn
ZHCSHA7E –JANUARY 2001–REVISED JANUARY 2018
8 Detailed Description
8.1 Overview
BLVDS drivers and receivers are intended to be used in a differential backplane configuration. Transceivers or
receivers are connected to the driver through a balanced media such as differential PCB traces. Typically, the
characteristic differential impedance of the media (ZO) is in the range of 50 Ω to 100 Ω. Two termination resistors
of ZO Ω each are placed at the ends of the transmission line backplane. The termination resistor converts the
current sourced by the driver into a voltage that is detected by the receiver. The effects of mid-stream
connector(s), cable stub(s), and other impedance discontinuity as well as ground shifting, noise margin limits,
and total termination loading must be taken into account.
8.2 Functional Block Diagram
DO1+/RI1+
DIN1
DO1-/RI1-
DE1
RO1
RE1
DO2+/RI2+
DIN2
DO2-/RI2-
RO2
DO3+/RI3+
DO3-/RI3-
DIN3
DE2
RO3
RE2
DO4+/RI4+
DIN4
DO4-/RI4-
RO4
Copyright © 2018, Texas Instruments Incorporated
8.3 Feature Description
The DS92LV040A differential line driver is a balanced current mode design. A current mode driver, generally
speaking has a high output impedance (100 Ω) and supplies a reasonably constant current for a range of loads
(a voltage mode driver on the other hand supplies a constant voltage for a range of loads). The current is
switched through the load in one direction to produce a logic state and in the other direction to produce the other
logic state.
版权 © 2001–2018, Texas Instruments Incorporated
9
DS92LV040A
ZHCSHA7E –JANUARY 2001–REVISED JANUARY 2018
www.ti.com.cn
Feature Description (接下页)
The current mode driver provides substantial benefits over voltage mode drivers, such as an RS-422 driver. Its
quiescent current remains relatively flat versus switching frequency. Whereas the RS-422 voltage mode driver
increases exponentially in most case between 20 MHz–50 MHz. This is due to the overlap current that flows
between the rails of the device when the internal gates switch. Whereas the current mode driver switches a fixed
current between its output without any substantial overlap current. This is similar to some ECL and PECL
devices, but without the heavy static ICC requirements of the ECL/PECL designs. LVDS requires 80% less
current than similar PECL devices. AC specifications for the driver are a tenfold improvement over other existing
RS-422 drivers. The TRI-STATE function allows the driver outputs to be disabled, thus obtaining an even lower
power state when the transmission of data is not required.
8.4 Device Functional Modes
表 1. Functional Table
MODE SELECTED
DRIVER MODE
DE
H
L
RE
H
L
RECEIVER MODE
TRI-STATE MODE
LOOP BACK MODE
L
H
L
H
表 2. Transmitter Mode
INPUTS
OUTPUTS
DE
H
DIN
DO+
L
DO−
L
H
L
H
H
H
H
0.8V< DIN <2.0V
X
X
X
Z
L
Z
表 3. Receiver Mode
INPUTS
(RI+) – (RI−)
OUTPUT
RE
L
L (< −70 mV)
H (> 0 mV)
L
H
X
Z
L
L
−70 mV < VID < 0 mV
X
H
10
版权 © 2001–2018, Texas Instruments Incorporated
DS92LV040A
www.ti.com.cn
ZHCSHA7E –JANUARY 2001–REVISED JANUARY 2018
9 Application and Implementation
注
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
The DS92LV040A is a Bus LVDS transceiver intended to be used in a differential backplane configuration.
Transceivers or receivers are connected to the driver through a balanced media such as differential PCB traces.
Typically, the characteristic differential impedance of the media (ZO) is in the range of 50 Ω to 100 Ω. Two
termination resistors of ZO Ω each are placed at the ends of the transmission line backplane. The termination
resistor converts the current sourced by the driver into a voltage that is detected by the receiver. The effects of
mid-stream connector(s), cable stub(s), and other impedance discontinuity as well as ground shifting, noise
margin limits, and total termination loading must be taken into account.
The output current is typically 12 mA. The current mode requires that a resistive termination be employed to
terminate the signal and to complete the loop. Unterminated configurations are not allowed. The 12 mA loop
current will develop a differential voltage of about 300 mV across a 27 Ω (double terminated 54Ω differential
transmission backplane) effective resistance, which the receiver detects with a 230 mV minimum differential
noise margin neglecting resistive line losses (driven signal minus receiver threshold (300 mV – 70 mV = 230
mV)). The signal is centered around +1.2 V (Driver Offset, VOS ) with respect to ground. Note that the steady-
state voltage (VSS) peak-to-peak swing is twice the differential voltage (VOD) and is typically 600 mV.
9.2 Typical Application
9.2.1 Multipoint Communications
In a multipoint configuration many transmitters and many receivers can be interconnected on a single
transmission line. The key difference compared to multi-drop is the presence of two or more drivers. Such a
situation creates contention issues that need not be addressed with point-to-point or multidrop systems.
Multipoint operation allows for bidirectional, half-duplex communication over a single balanced media pair. To
support the location of the various drivers throughout the transmission line, double termination of the
transmission line is now necessary.
The major challenge that system designers encounter are the impedance discontinuities that device loading and
device connections (stubs) introduce on the common bus. Matching the impedance of the loaded bus and using
signal drivers with controlled signal edges are the keys to error-free signal transmissions in multipoint topologies.
D0+
D0+
DIN
DIN
RT
RT
D0-
D0-
DE
RE
DE
RE
RI+
RI+
+
-
+
-
ROUT
ROUT
RI-
RI-
Copyright © 2018, Texas Instruments Incorporated
图 10. Bidirectional Half-Duplex Point-to-Point Applications
版权 © 2001–2018, Texas Instruments Incorporated
11
DS92LV040A
ZHCSHA7E –JANUARY 2001–REVISED JANUARY 2018
www.ti.com.cn
Typical Application (接下页)
DIN / ROUT
DIN / ROUT
DIN / ROUT
DIN / ROUT
RT
RT
DIN / ROUT
DIN / ROUT
DIN / ROUT
Copyright © 2018, Texas Instruments Incorporated
图 11. Multi-Point Bus Applications
9.2.2 Design Requirements
For this design example, use the parameters listed in 表 4.
表 4. Design Parameters
PARAMETERS
Driver supply voltage
VALUES
3 to 3.6 V
Driver input voltage
0.8 to 3.3 V
DC to 200 Mbps
100 Ω
Driver signaling rate
Interconnect characteristic impedance
Termination resistance (differential)
Number of receiver nodes
Receiver supply voltage
100 Ω
2 to 32
3 to 3.6 V
Receiver input voltage
0 to (VCC – 0.8) V
DC to 200 Mbps
±1 V
Receiver signaling rate
Ground shift between driver and receiver
9.2.3 Detailed Design Procedure
9.2.3.1 Supply Voltage
The DS92LV040A is operated from a single supply. The device can support operations with a supply as low as
3 V and as high as 3.6 V.
9.2.3.2 Supply Bypass Capacitance
Bypass capacitors play a key role in power distribution circuitry. At low frequencies, power supply offers very low-
impedance paths between its terminals. However, as higher frequency currents propagate through power traces,
the source is often incapable of maintaining a low-impedance path to ground. Bypass capacitors are used to
address this shortcoming. Usually, large bypass capacitors (10 μF to 1000 μF) at the board level do a good job
up into the kHz range. Due to their size and length of their leads, large capacitors tend to have large inductance
values at the switching frequencies. To solve this problem, smaller capacitors (in the nF to μF range) must be
installed locally next to the integrated circuit.
12
版权 © 2001–2018, Texas Instruments Incorporated
DS92LV040A
www.ti.com.cn
ZHCSHA7E –JANUARY 2001–REVISED JANUARY 2018
9.2.3.3 Termination Resistors
Multipoint LVDS communication channel employs a current source driving a transmission line which is terminated
with two resistive loads. These loads serve to convert the transmitted current into a voltage at the receiver input.
To ensure good signal integrity, the termination resistors should be matched to the characteristic impedance of
the transmission line. The designer should ensure that the termination resistors are within 10% of the nominal
media characteristic impedance. If the transmission line is targeted for 100-Ω impedance, the termination
resistors should be between 90 Ω and 110 Ω. The line termination resistors are typically placed at the ends of the
transmission line.
9.2.3.4 Interconnecting Media
The backplane and connectors should have a matched differential impedance. Use controlled impedance traces
which match the differential impedance of your transmission medium (ie. backplane or cable) and termination
resistor(s). Run the differential pair trace lines as close together as possible as soon as they leave the IC. This
helps eliminate reflections and ensure noise is coupled as common-mode. In fact, it has been determined that
differential signals which are 1 mm apart radiate far less noise than traces 3 mm apart since magnetic field
cancellation is much better with the closer traces. Plus, noise induced on the differential lines is much more likely
to appear as common-mode which is rejected by the receiver. Match electrical lengths between traces to reduce
skew. Skew between the signals of a pair means a phase difference between signals which destroys the
magnetic field cancellation benefits of differential signals and EMI will result.
Stub lengths should be kept to a minimum. The typical transition time of the DS92LV040A Bus LVDS output is
0.75 ns (20% to 80%). The extrapolated 100 percent time is 0.75/0.6 or 1.25 ns. For a general approximation, if
the electrical length of a trace is greater than 1/5 of the transition edge, then the trace is considered a
transmission line. For example, 1.25 ns/5 is 250 picoseconds. Let velocity equal 160 ps per inch for a typical
loaded backplane. Then maximum stub length is 250 ps/160 ps/in or 1.56 inches. To determine the maximum
stub for the backplane, determine the propagation velocity for the actual conditions (refer to application notes AN
905 and AN 808)
10 Power Supply Recommendations
The driver and receivers in this data sheet are designed to operate from a single power supply. Both drivers and
receivers operate with supply voltages in the range of 3 V to 3.6 V. In a typical application, a driver and a
receiver may be on separate boards, or even separate equipment. In these cases, separate supplies would be
used at each location. The expected ground potential difference between the driver power supply and the
receiver power supply would be less than ±1 V. Board level and local device level bypass capacitance should be
used and are covered Supply Bypass Capacitance.
版权 © 2001–2018, Texas Instruments Incorporated
13
DS92LV040A
ZHCSHA7E –JANUARY 2001–REVISED JANUARY 2018
www.ti.com.cn
11 Layout
11.1 Layout Guidelines
11.1.1 Microstrip vs. Stripline Topologies
As per SLLD009, printed-circuit boards usually offer designers two transmission line options: Microstrip and
stripline. Microstrips are traces on the outer layer of a PCB, as shown in 图 12.
图 12. Microstrip Topology
Striplines are traces between two ground planes. Striplines are less prone to emissions and susceptibility
problems because the reference planes effectively shield the embedded traces. However, from the standpoint of
high-speed transmission, juxtaposing two planes creates additional capacitance. TI recommends routing the
signals on microstrip transmission lines if possible. The PCB traces allow designers to specify the necessary
tolerances for ZO based on the overall noise budget and reflection allowances. Footnotes 1(1), 2(2), and 3(3)
(1) (2) (3)
provide formulas for ZO and tPD for differential and single-ended traces.
图 13. Stripline Topology
11.1.2 Dielectric Type and Board Construction
The speeds at which signals travel across the board dictates the choice of dielectric. FR-4, or equivalent, usually
provides adequate performance for use with multipoint LVDS signals. If rise or fall times of TTL/CMOS signals
are less than 500 ps, empirical results indicate that a material with a dielectric constant near 3.4, such as
Rogers™ 4350 or Nelco N4000-13 is better suited. Once the designer chooses the dielectric, there are several
parameters pertaining to the board construction that can affect performance. The following set of guidelines were
developed experimentally through several designs involving multipoint LVDS devices:
•
Copper weight: 15 g or 1/2 oz start, plated to 30 g or 1 oz
(1) Howard Johnson & Martin Graham.1993. High Speed Digital Design – A Handbook of Black Magic. Prentice Hall PRT. ISBN number
013395724.
(2) Mark I. Montrose. 1996. Printed Circuit Board Design Techniques for EMC Compliance. IEEE Press. ISBN number 0780311310.
(3) Clyde F. Coombs, Jr. Ed, Printed Circuits Handbook, McGraw Hill, ISBN number 0070127549.
14
版权 © 2001–2018, Texas Instruments Incorporated
DS92LV040A
www.ti.com.cn
ZHCSHA7E –JANUARY 2001–REVISED JANUARY 2018
Layout Guidelines (接下页)
•
•
•
All exposed circuitry should be solder-plated (60/40) to 7.62 μm or 0.0003 in (minimum).
Copper plating should be 25.4 μm or 0.001 in (minimum) in plated-through-holes.
Solder mask over bare copper with solder hot-air leveling
11.1.3 Recommended Stack Layout
Following the choice of dielectrics and design specifications, you must decide how many levels to use in the
stack. To reduce the TTL/CMOS to multipoint LVDS crosstalk, it is a good practice to have at least two separate
signal planes as shown in 图 14.
Layer 1: Routed Plane (MLVDS Signals)
Layer 2: Ground Plane
Layer 3: Power Plane
Layer 4: Routed Plane (TTL/CMOS Signals)
图 14. Four-Layer PCB Board
注
The separation between layers 2 and 3 should be 127 μm (0.005 in). By keeping the
power and ground planes tightly coupled, the increased capacitance acts as a bypass for
transients.
One of the most common stack configurations is the six-layer board, as shown in 图 15.
Layer 1: Routed Plane (MLVDS Signals)
Layer 2: Ground Plane
Layer 3: Power Plane
Layer 4: Ground Plane
Layer 5: Ground Plane
Layer 4: Routed Plane (TTL Signals)
图 15. Six-Layer PCB Board
In this particular configuration, it is possible to isolate each signal layer from the power plane by at least one
ground plane. The result is improved signal integrity; however, fabrication is more expensive. Using the 6-layer
board is preferable, because it offers the layout designer more flexibility in varying the distance between signal
layers and referenced planes, in addition to ensuring reference to a ground plane for signal layers 1 and 6.
11.1.4 Separation Between Traces
The separation between traces depends on several factors; however, the amount of coupling that can be
tolerated usually dictates the actual separation. Low noise coupling requires close coupling between the
differential pair of an multipoint LVDS link to benefit from the electromagnetic field cancellation. In addition,
differential pairs should have the same electrical length to ensure that they are balanced, thus minimizing
problems with skew and signal reflection.
If there are two adjacent single-ended traces, one should use the 3-W rule, which stipulates that the distance
between two traces must be greater than two times the width of a single trace, or three times its width measured
from trace center to trace center. This increased separation effectively reduces the potential for crosstalk. The
same rule should be applied to the separation between adjacent multipoint LVDS differential pairs, whether the
traces are edge-coupled or broad-side-coupled.
版权 © 2001–2018, Texas Instruments Incorporated
15
DS92LV040A
ZHCSHA7E –JANUARY 2001–REVISED JANUARY 2018
www.ti.com.cn
Layout Guidelines (接下页)
W
MLVDS
Pair
Minimum spacing as
defined by PCB vendor
Differential Traces
S =
W
í 2 W
W
Single-Ended Traces
TTL/CMOS
Trace
图 16. 3-W Rule for Single-Ended and Differential Traces (Top View)
You should exercise caution when using autorouters, because they do not always account for all factors affecting
crosstalk and signal reflection. For instance, it is best to avoid sharp 90° turns to prevent discontinuities in the
signal path. Using successive 45° turns tends to minimize reflections.
11.1.5 Crosstalk and Ground Bounce Minimization
To reduce crosstalk, it is important to provide a return path to high-frequency currents that is as close as possible
to its originating trace. A ground plane usually achieves this. Because the returning currents always choose the
path of lowest inductance, they are most likely to return directly under the original trace, thus minimizing
crosstalk. Lowering the area of the current loop lowers the potential for crosstalk. Traces kept as short as
possible with an uninterrupted ground plane running beneath them emit the minimum amount of electromagnetic
field strength. Discontinuities in the ground plane increase the return path inductance and should be avoided.
11.1.6 Decoupling
Each power or ground lead of a high-speed device should be connected to the PCB through a low inductance
path. For best results, one or more vias are used to connect a power or ground pin to the nearby plane. Ideally,
via placement is immediately adjacent to the pin to avoid adding trace inductance. Placing a power plane closer
to the top of the board reduces the effective via length and its associated inductance.
V
Via
GND
Via
CC
TOP signal layer + GND fill
1 plane
4 mil
6 mil
V
DD
2 mil
Buried capacitor
>
GND plane
Signal layer
GND plane
Signal layers
V
plane
CC
Signal layer
GND plane
Buried capacitor
>
V
2 plane
DD
4 mil
6 mil
BOTTOM signal layer + GND fill
Typical 12-Layer PCB
图 17. Low Inductance, High-Capacitance Power Connection
Bypass capacitors should be placed close to VDD pins. They can be placed conveniently near the corners or
underneath the package to minimize the loop area. This extends the useful frequency range of the added
capacitance. Small-physical-size capacitors, such as 0402, 0201, or X7R surface-mount capacitors should be
used to minimize body inductance of capacitors. Each bypass capacitor is connected to the power and ground
plane through vias tangent to the pads of the capacitor as shown in 图 18(a).
16
版权 © 2001–2018, Texas Instruments Incorporated
DS92LV040A
www.ti.com.cn
ZHCSHA7E –JANUARY 2001–REVISED JANUARY 2018
Layout Guidelines (接下页)
An X7R surface-mount capacitor of size 0402 has about 0.5 nH of body inductance. At frequencies above 30
MHz or so, X7R capacitors behave as low-impedance inductors. To extend the operating frequency range to a
few hundred MHz, an array of different capacitor values like 100 pF, 1 nF, 0.03 μF, and 0.1 μF are commonly
used in parallel. The most effective bypass capacitor can be built using sandwiched layers of power and ground
at a separation of 2 to 3 mils. With a 2-mil FR4 dielectric, there is approximately 500 pF per square inch of PCB.
Many high-speed devices provide a low-inductance GND connection on the backside of the package. This center
pad must be connected to a ground plane through an array of vias. The via array reduces the effective
inductance to ground and enhances the thermal performance of the small Surface Mount Technology (SMT)
package. Placing vias around the perimeter of the pad connection ensures proper heat spreading and the lowest
possible die temperature. Placing high-performance devices on opposing sides of the PCB using two GND
planes creates multiple paths for heat transfer. Often thermal PCB issues are the result of one device adding
heat to another, resulting in a very high local temperature. Multiple paths for heat transfer minimize this
possibility. In many cases the GND pad makes the optimal decoupling layout impossible to achieve due to
insufficient pad-to-pad spacing as shown in 图 18(b). When this occurs, placing the decoupling capacitor on the
backside of the board keeps the extra inductance to a minimum. It is important to place the VDD via as close to
the device pin as possible while still allowing for sufficient solder mask coverage. If the via is left open, solder
may flow from the pad and into the via barrel. This results in a poor solder connection.
(a)
(b)
V
DD
0402
INœ
IN+
0402
图 18. Typical Decoupling Capacitor Layouts
11.2 Layout Example
At least two or three times the width of an individual trace should separate single-ended traces and differential
pairs to minimize the potential for crosstalk. Single-ended traces that run in parallel for less than the wavelength
of the rise or fall times usually have negligible crosstalk. Increase the spacing between signal paths for long
parallel runs to reduce crosstalk. Boards with limited real estate can benefit from the staggered trace layout, as
shown in 图 19.
Layer 1
Layer 6
图 19. Staggered Trace Layout
版权 © 2001–2018, Texas Instruments Incorporated
17
DS92LV040A
ZHCSHA7E –JANUARY 2001–REVISED JANUARY 2018
www.ti.com.cn
Layout Example (接下页)
This configuration lays out alternating signal traces on different layers; thus, the horizontal separation between
traces can be less than 2 or 3 times the width of individual traces. To ensure continuity in the ground signal path,
TI recommends having an adjacent ground via for every signal via, as shown in 图 20. Note that vias create
additional capacitance. For example, a typical via has a lumped capacitance effect of 1/2 pF to 1 pF in FR4.
Signal Via
Signal Trace
Uninterrupted Ground Plane
Signal Trace
Uninterrupted Ground Plane
Ground Via
图 20. Ground Via Location (Side View)
Short and low-impedance connection of the device ground pins to the PCB ground plane reduces ground
bounce. Holes and cutouts in the ground planes can adversely affect current return paths if they create
discontinuities that increase returning current loop areas.
To minimize EMI problems, TI recommends avoiding discontinuities below a trace (for example, holes, slits, and
so on) and keeping traces as short as possible. Zoning the board wisely by placing all similar functions in the
same area, as opposed to mixing them together, helps reduce susceptibility issues.
18
版权 © 2001–2018, Texas Instruments Incorporated
DS92LV040A
www.ti.com.cn
ZHCSHA7E –JANUARY 2001–REVISED JANUARY 2018
12 器件和文档支持
12.1 Documentation Support
12.1.1 Related Documentation
一般应用指南和提示可在以下应用手册中找到:), A)。
如需相关文档,请参阅:
•
•
•
•
AN-808 (SNLA028)
AN-977 (SNLA166
AN-971 (SNLA165)
AN-903 (SNLA034
12.2 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. 有关更改的详细信息,请查看任何已修订文档中包含的修订历史记录。
12.3 Community Resources
下列链接提供到 TI 社区资源的连接。链接的内容由各个分销商“按照原样”提供。这些内容并不构成 TI 技术规范,
并且不一定反映 TI 的观点;请参阅 TI 的 《使用条款》。
TI E2E™ 在线社区 TI 的工程师对工程师 (E2E) 社区。此社区的创建目的在于促进工程师之间的协作。在
e2e.ti.com 中,您可以咨询问题、分享知识、拓展思路并与同行工程师一道帮助解决问题。
设计支持
TI 参考设计支持 可帮助您快速查找有帮助的 E2E 论坛、设计支持工具以及技术支持的联系信息。
12.4 商标
E2E is a trademark of Texas Instruments.
Rogers is a trademark of Rogers Corporation.
All other trademarks are the property of their respective owners.
12.5 静电放电警告
ESD 可能会损坏该集成电路。德州仪器 (TI) 建议通过适当的预防措施处理所有集成电路。如果不遵守正确的处理措施和安装程序 , 可
能会损坏集成电路。
ESD 的损坏小至导致微小的性能降级 , 大至整个器件故障。 精密的集成电路可能更容易受到损坏 , 这是因为非常细微的参数更改都可
能会导致器件与其发布的规格不相符。
12.6 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 机械、封装和可订购信息
以下页面包含机械、封装和可订购信息。这些信息是指定器件的最新可用数据。数据如有变更,恕不另行通知和修
订此文档。如欲获取此数据表的浏览器版本,请参阅左侧的导航。
版权 © 2001–2018, Texas Instruments Incorporated
19
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
DS92LV040ATLQA/NOPB
DS92LV040ATLQAX/NOPB
ACTIVE
ACTIVE
WQFN
WQFN
NJN
NJN
44
44
250
RoHS & Green
SN
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
-40 to 85
-40 to 85
LV040A
LV040A
2500 RoHS & Green
SN
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
3-Jun-2022
TAPE AND REEL INFORMATION
REEL DIMENSIONS
TAPE DIMENSIONS
K0
P1
W
B0
Reel
Diameter
Cavity
A0
A0 Dimension designed to accommodate the component width
B0 Dimension designed to accommodate the component length
K0 Dimension designed to accommodate the component thickness
Overall width of the carrier tape
W
P1 Pitch between successive cavity centers
Reel Width (W1)
QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE
Sprocket Holes
Q1 Q2
Q3 Q4
Q1 Q2
Q3 Q4
User Direction of Feed
Pocket Quadrants
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
DS92LV040ATLQA/NOPB WQFN
NJN
NJN
44
44
250
178.0
330.0
16.4
16.4
7.3
7.3
7.3
7.3
1.3
1.3
12.0
12.0
16.0
16.0
Q1
Q1
DS92LV040ATLQAX/
NOPB
WQFN
2500
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
3-Jun-2022
TAPE AND REEL BOX DIMENSIONS
Width (mm)
H
W
L
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
DS92LV040ATLQA/NOPB
WQFN
WQFN
NJN
NJN
44
44
250
208.0
356.0
191.0
356.0
35.0
35.0
DS92LV040ATLQAX/
NOPB
2500
Pack Materials-Page 2
MECHANICAL DATA
NJN0044A
LQA44A (REV B)
www.ti.com
重要声明和免责声明
TI“按原样”提供技术和可靠性数据(包括数据表)、设计资源(包括参考设计)、应用或其他设计建议、网络工具、安全信息和其他资源,
不保证没有瑕疵且不做出任何明示或暗示的担保,包括但不限于对适销性、某特定用途方面的适用性或不侵犯任何第三方知识产权的暗示担
保。
这些资源可供使用 TI 产品进行设计的熟练开发人员使用。您将自行承担以下全部责任:(1) 针对您的应用选择合适的 TI 产品,(2) 设计、验
证并测试您的应用,(3) 确保您的应用满足相应标准以及任何其他功能安全、信息安全、监管或其他要求。
这些资源如有变更,恕不另行通知。TI 授权您仅可将这些资源用于研发本资源所述的 TI 产品的应用。严禁对这些资源进行其他复制或展示。
您无权使用任何其他 TI 知识产权或任何第三方知识产权。您应全额赔偿因在这些资源的使用中对 TI 及其代表造成的任何索赔、损害、成
本、损失和债务,TI 对此概不负责。
TI 提供的产品受 TI 的销售条款或 ti.com 上其他适用条款/TI 产品随附的其他适用条款的约束。TI 提供这些资源并不会扩展或以其他方式更改
TI 针对 TI 产品发布的适用的担保或担保免责声明。
TI 反对并拒绝您可能提出的任何其他或不同的条款。IMPORTANT NOTICE
邮寄地址:Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2022,德州仪器 (TI) 公司
相关型号:
DS92LV0411SQENOPB
IC LINE DRIVER, QCC36, 6 X 6 MM, 0.80 MM HEIGHT, 0.50 MM PITCH, ROHS COMPLIANT, LLP-36, Line Driver or Receiver
NSC
©2020 ICPDF网 联系我们和版权申明