ERJ-3GEYJ301V [TI]
INA223EVM Userâs Guide and Software Tutorial; INA223EVM USERA ????指南和软件教程
| 型号： | ERJ-3GEYJ301V |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | INA223EVM Userâs Guide and Software Tutorial |
| 文件： | 总26页 (文件大小：1323K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
User's Guide
SBOU125–June 2012
INA223EVM User’s Guide and Software Tutorial
INA223EVM
This user's guide describes the characteristics, operation, and use of the INA223EVM evaluation board. It
discusses how to set up and configure the software and hardware, and reviews various aspects of the
program operation. This user's guide also includes information regarding operating procedures and
input/output connections, an electrical schematic, printed circuit board (PCB) layout drawings, and a parts
list for the EVM.
Throughout this document, the terms evaluation board, evaluation module, and EVM are synonymous with
the INA223EVM.
Microsoft, Windows are registered trademarks of Microsoft Corporation.
SPI is a trademark of Motorola Inc,.
I2C is a trademark of NXP Semiconductors.
1
SBOU125–June 2012
INA223EVM User’s Guide and Software Tutorial
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
www.ti.com
INA223EVM (continued)
Contents
1
2
3
4
5
6
Overview ..................................................................................................................... 3
INA223EVM Hardware Setup ............................................................................................. 4
INA223EVM Hardware Overview ......................................................................................... 7
INA223EVM Software Setup ............................................................................................. 12
INA223EVM Software Overview ......................................................................................... 14
INA223EVM Documentation ............................................................................................. 22
List of Figures
1
Hardware Included with INA223EVM Kit.................................................................................
Hardware Setup.............................................................................................................
INA223 Test Board Block Diagram .......................................................................................
SM-USB-DIG Platform Block Diagram ...................................................................................
Typical Hardware Test Connections on the INA223EVM..............................................................
Connecting the USB Cable to the SM-USB-DIG Platform.............................................................
Confirmation of SM-USB-DIG Platform Driver Installation.............................................................
INA223EVM Default Jumpers .............................................................................................
3
4
5
6
7
8
8
9
2
3
4
5
6
7
8
9
Typical Filter Setup........................................................................................................ 11
INA223 Shunt Configurations............................................................................................ 11
Software Install Window .................................................................................................. 12
Software License Agreement ............................................................................................ 13
Software Install Progress................................................................................................. 13
INA223EVM Software Interface ......................................................................................... 14
Communication Error with SM-USB-DIG Platform .................................................................... 14
Setting the A0 Address ................................................................................................... 15
Configuring the Output Mode ............................................................................................ 16
Configuring the Bus Voltage Gain....................................................................................... 18
Configuring the Current Shunt Voltage Gain .......................................................................... 18
Register Table ............................................................................................................. 19
Auto-Write, Power, and Voltage Controls .............................................................................. 20
Example Hardware Calculator ........................................................................................... 21
INA223EVM Board Schematic........................................................................................... 23
INA223EVM PCB Component Layout .................................................................................. 24
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
List of Tables
1
2
3
4
5
6
Related Documentation ....................................................................................................
INA223EVM H1 Pin Connections.........................................................................................
INA223 Test Board Jumper Functions ...................................................................................
4
5
9
INA223 I2C Address Configuration ...................................................................................... 15
Power Gain Values........................................................................................................ 17
Bill of Materials ............................................................................................................ 22
2
INA223EVM User’s Guide and Software Tutorial
SBOU125–June 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
www.ti.com
Overview
1
Overview
The INA223 is a voltage output device that monitors current, bus voltage, and power of a supply line by
sensing a voltage drop across a shunt. The INA223EVM is a platform for evaluating the performance of
the INA223 under various signal, shunt, and supply conditions. This document gives a general overview of
the INA223EVM, and provides a general description of the features and functions to be considered while
using this evaluation module.
1.1 INA223EVM Kit Contents
The INA223EVM kit includes the following items:
•
•
•
•
•
(1) INA223 PCB evaluation board
(1) SM-USB-DIG Platform PCB
(1) USB extender cable
(1) SM-USB-DIG connector ribbon cable
(1) User’s guide CD-ROM
Figure 1 shows all of the included hardware. Contact the Texas Instruments Product Information Center
nearest you if any component is missing. It is highly recommended that you check the TI web site at
http://www.ti.com to verify that you have the latest versions of the related software.
USB Extender Cable
SM-USB-DIG
Connector
Ribbon Cable
INA223EVM
Board
SM-USB-DIG
Figure 1. Hardware Included with INA223EVM Kit
3
SBOU125–June 2012
Submit Documentation Feedback
INA223EVM User’s Guide and Software Tutorial
Copyright © 2012, Texas Instruments Incorporated
INA223EVM Hardware Setup
www.ti.com
1.2 Related Documentation
The following document provides information regarding Texas Instruments integrated circuits used in the
assembly of the INA223EVM. This user's guide is available from the TI web site under literature number
SBOU125 . Any letter appended to the literature number corresponds to the document revision that is
current at the time of the writing of this document. Newer revisions may be available from the TI web site
at http://www.ti.com, or call the Texas Instruments Literature Response Center at (800) 477-8924 or the
Product Information Center at (972) 644-5580. When ordering, identify the document by both title and
literature number.
Table 1. Related Documentation
Document
Literature Number
SBOS528
INA223 Product Data Sheet
SM-USB-DIG Platform User’s Guide
SBOU098
2
INA223EVM Hardware Setup
This section discusses the overall system setup for the INA223EVM. A PC runs software that
communicates with the SM-USB-DIG Platform. This platform generates the analog and digital signals
used to communicate with the INA223 board. Connectors on the INA223 allow the user to connect to the
system under test conditions where the power, current, and voltage are monitored.
Analog Supply
Power Supply
USB SM-DIG
INA223EVM
Shunt
Load
GND
Figure 2. Hardware Setup
4
INA223EVM User’s Guide and Software Tutorial
SBOU125–June 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
www.ti.com
INA223EVM Hardware Setup
2.1 Theory of Operation for INA223 Hardware
A block diagram of the INA223 test-board hardware setup is shown in Figure 3. The PCB provides
connections to the I2C™ and general-purpose inputs and outputs (GPIO) on the SM-USB-DIG Platform
board. It also provides connection points for external connections to the shunt voltage.
Shunt
Terminal
T2
Supply Voltage
2
A0
Vs
Vdut
H1
INA223
JMP1/JMP2
I2C Addr
Jumper
I2C Interface
Figure 3. INA223 Test Board Block Diagram
2.2 Signal Definitions of H1 (10-Pin Male Connector Socket)
Table 2 shows the pinout for the 10-pin connector socket used to communicate between the INA223EVM
and the SM-USB-DIG. It should be noted that to issue commands to the INA223 chip, the INA223EVM
only uses H1 connnector pins 1 and 3 (I2C communication lines), pin 6 (VDUT), and pin 8 (GND).
Table 2. INA223EVM H1 Pin Connections
Pin on H1
Signal
I2C_SCL
CTRL/MEAS4(1)
Description
1
2
3
4
5
6
I2C clock signal (SCL)
GPIO—Control output or measure input
I2C data signal (SDA)
I2C_SDA1
CTRL/MEAS5(1)
SPI_DOUT3(1)
VDUT
GPIO—Control output or measure input
SPI™ data output (MOSI)
Switchable DUT power supply: +3.3V, +5V, Hi-Z
(disconnected).(2)
7
8
SPI_CLK(1)
GND
SPI clock signal (SCLK)
Power return (GND)
9
SPI_CS1(1)
SPI_DIN1(1)
SPI chip select signal (CS)
SPI data input (MISO)
10
(1)
(2)
This signal is not used on the INA223EVM.
When VDUT is Hi-Z, all digital inputs and outputs (I/O) are Hi-Z as well.
5
SBOU125–June 2012
INA223EVM User’s Guide and Software Tutorial
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
INA223EVM Hardware Setup
www.ti.com
2.3 Theory of Operation for SM-USB-DIG Platform
Figure 4 shows the block diagram for the SM-USB-DIG Platform. This platform is a general-purpose data
acquisition system that is used on several different Texas Instruments evaluation modules. The details of
its operation are included in a separate document (SBOU098). The block diagram shown in Figure 4 is
given as a brief overview of the SM-USB-DIG Platform.
SM-USB-DIG
3.3-V
Regulator
USB
+5.0 V
+3.3 V
USB Bus
from
Computer
TUSB3210
8052 Microcontroller
w/USB Interface
and UART
I2C
SPI
Control Bits
Measure Bits
Buffer and
Level
Translators
Power-On
Reset
8K ´ 8 Byte
EEPROM
VDUT
(Hi-Z, 3.3 V, or 5 V)
Switched Power
Power
Switching
USB +5.0 V
+3.3 V
Figure 4. SM-USB-DIG Platform Block Diagram
The brain of the SM-USB-DIG Platform is the TUSB3210, an 8052 microcontroller that has a built-in USB
interface. The microcontroller receives information from the host computer that is interpreted into power,
I2C, SPI, and other digital I/O patterns. During the digital I/O transaction, the microcontroller reads the
response of any device connected to the I/O interface. The response from the device is sent back to the
PC where it is interpreted by the host computer.
6
INA223EVM User’s Guide and Software Tutorial
SBOU125–June 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
www.ti.com
INA223EVM Hardware Overview
3
INA223EVM Hardware Overview
The INA223EVM hardware setup involves connecting the two EVM PCBs together, applying power,
connecting the USB cable, and setting the jumpers. This section describes the details of this procedure.
3.1 Electrostatic Discharge Warning
Many of the components on the INA223EVM are susceptible to damage by electrostatic discharge (ESD).
Customers are advised to observe proper ESD handling precautions when unpacking and handling the
EVM, including the use of a grounded wrist strap at an approved ESD workstation.
3.2 Connecting the Hardware
To connect the INA223 test board and the SM-USB-DIG Platform together, gently slide the male and
female ends of the 10-pin connectors together. Make sure that the two connectors are completely pushed
together; loose connections may cause intermittent operation.
3.3 Connecting Power
After the EVM and SM-USB-DIG are joined, as shown in Figure 5, connect the desired VBUS and shunt
configuration to be measured. Typically, setup involves a high- or low-side load and a shunt resistor
across VIN+ and VIN–. The example in Figure 5 represents a test scenario with a low-side shunt attached.
The power supply for VBUS is not included with the kit and is supplied by the customer; the specific voltage
needed depends on your testing needs.
Figure 5. Typical Hardware Test Connections on the INA223EVM
7
SBOU125–June 2012
INA223EVM User’s Guide and Software Tutorial
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
INA223EVM Hardware Overview
www.ti.com
3.4 Connecting the USB Cable to the SM-USB-DIG Platform
Figure 6 shows the USB connection to the SM-USB-DIG Platform board. The first time you connect to the
PC, the computer typically responds with a Found New Hardware, USB Device pop-up window. The pop-
up window then likely changes to Found New Hardware, USB Human Interface Device. The SM-USB-DIG
®
®
Platform uses the human interface device drivers that are part of with Microsoft Windows operating
systems.
Figure 6. Connecting the USB Cable to the SM-USB-DIG Platform
In some cases, the Windows Add Hardware Wizard is shown. If this prompt appears, allow the system
device manager to install the human interface drivers by clicking Yes when requested to install drivers.
Windows confirms installation of the drivers with the message shown in Figure 7. This pop-up indicates
that the device is ready to be used.
Figure 7. Confirmation of SM-USB-DIG Platform Driver Installation
8
INA223EVM User’s Guide and Software Tutorial
SBOU125–June 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
www.ti.com
INA223EVM Hardware Overview
3.5 INA223EVM Default Jumper Settings
Figure 8 shows the default jumper configuration for the INA223EVM. You may want to change some of the
jumpers on the INA223EVM to match your specific configuration. For example, you may wish to set a
specific I2C address by configuring jumper 1 (JMP1) and jumper 2 (JMP2).
Figure 8. INA223EVM Default Jumpers
Jumper 3 (JMP3) on the INA223EVM is typically set to the internal (INT) position. When set to the INT
position, the device supply voltage is generated and controlled from the SM-USB-DIG Platform. When this
jumper is set to the external (EXT) position, INA223 pin 4 (VS) connects to terminal strip T1 and can be
powered from an external supply.
JMP1 and JMP2 control the I2C address pin for the INA223; these jumpers set the address for A0 to either
high, low, SCL, or SDA. Make sure to connect only one jumper at a time for the address control (for
example, if JMP1 is connected, do not connect JMP2, and vice versa). Failure to properly connect
jumpers can cause shorts or interruptions in the communication lines. For more information on the INA223
addressing, consult the INA223 data sheet (SBOS528).
Table 3 summarizes the function of the INA223 test board jumpers. For most applications, all the jumpers
should be left in their default configurations.
Table 3. INA223 Test Board Jumper Functions
Jumper
JMP1
Default
Open
GND
Description
These jumpers select the I2C AO address selection for A0. Four
separate I2C addresses can be selected,depending on whether JMP2
is set to high or low, or JMP1 is set to SDA or SCL.
JMP2
JMP3
INT
This jumper selects whether the VS pin on the INA223 is connected to
the digital power-supply signal (VDUT) generated from the SM-USB-
DIG Platform (INT position), or whether the VDUT pin is connected to
terminal T1, thus allowing for an external supply to power the digital
circuitry (EXT position).
9
SBOU125–June 2012
Submit Documentation Feedback
INA223EVM User’s Guide and Software Tutorial
Copyright © 2012, Texas Instruments Incorporated
INA223EVM Hardware Overview
www.ti.com
3.6 INA223EVM Hardware
This section describes some of the hardware features present on the INA223EVM board.
3.6.1
JMP3: I2C versus Control Setting
The JMP3 setting determines if the INA223 is powered from the SM-USB-DIG platform or an external
power supply. If JMP3 is set to the INT position, the VS pin is connected to the switchable VDUT signal
generated from the SM-USB-DIG Platform. This voltage can be set to either 3.3 V or 5 V, depending on
how it is configured in the software.
When JMP3 is set to the EXT position, an external supply connected to terminal T1 must be used to
provide the digital supply voltage for the INA223.
3.6.2
3.6.3
JMP1 and JMP2: I2C Address Hardware Setting (A0)
JMP1 and JMP2 are used to set the hardware setting for the A0 I2C address pin on the INA223. Using
JMP2, the A0 address can be set to either a logic '1' or a logic '0'. Using JMP1, the A0 address can be set
to either the SCL or SDA communication line. Make sure to only have a jumper installed on JMP1 or
JMP2. Failure to keep these lines separate can lead to board shorts and problems with the I2C
communication lines. See the I2C Address Selection section for how to configure the INA223EVM
software to match the JMP1 and JMP2 hardware settings.
External I2C lines and Terminal Block T3
The I2C communication lines on the INA223EVM are tied to two sources: The internal I2C communication
lines from the SM-USB-DIG Platform and terminal block T3. If external signals separate from the SM-USB-
DIG are to be used, simply disconnect the SM-USB-DIG from the INA223 board and connect to external
SDA, SCL, and GND lines. Also, remember to apply an external VS that is compatible with the I2C
communication device being used.
CAUTION
Failure to disconnect the SM-USB-DIG Platform while using external I2C
communication can cause damage to the SM-USB-DIG or external
communication device.
10
INA223EVM User’s Guide and Software Tutorial
SBOU125–June 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
www.ti.com
INA223EVM Hardware Overview
3.6.4
VIN+ and VIN– Input Filter (R4, R3, and C3)
The INA223EVM has an optional input filter located between the terminal block T2 and the INA223 input
pins. This filter helps to remove high-frequency noise from the VIN+ and VIN– inputs. The EVM ships with
this filter not used. C3 is typically unpopulated and R3 and R4 have 0-Ω resistors installed. If filtering is
desired, limit the value for R3 and R4 to 10-Ω or less. Figure 9 shows the typical setup that is
recommended for basic INA223 evaluation. See the INA223 data sheet (SBOS528) for more details.
0 W Resistors
Unpopulated C3
Figure 9. Typical Filter Setup
3.6.5
Shunt Monitor Configuration and Terminal Block T2
The INA223 is typically used in a high-side configuration, as shown in Figure 10. The T2 terminal block
includes the connections for VIN+ and VIN–, which should be connected directly across the shunt resistor.
Depending on the user’s needs, either of these configurations may be used without any changes needed
to the INA223EVM board or software.
CBYPASS
RSHUNT
0.1mF
Power Supply
(0V to 26V)
Load
VS (Supply Voltage)
Attenuator
RPULLUP
4.7kW
VIN-
VOUT
SCL
SDA
A0
VIN+
Two-Wire
Interface
INA223
GND
Figure 10. INA223 Shunt Configurations
11
SBOU125–June 2012
INA223EVM User’s Guide and Software Tutorial
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
INA223EVM Software Setup
www.ti.com
4
INA223EVM Software Setup
This section discusses how to install the INA223 software.
4.1 Operating Systems for INA223EVM Software
The INA223 software has been tested on the Microsoft Windows XP operating system (OS) with United
States and European regional settings. This software should also function on other Windows operating
systems.
4.2 INA223 Software Installation
The INA223EVM software is included on the CD that is shipped with the EVM kit. It is also available
through the INA223EVM product folder on the TI web site. To download the software to your system,
insert the disc into an available CD-ROM drive. Navigate to the drive contents and open the INA223EVM
software folder. Locate the compressed file (INA223EVM.zip) and open it. Extract the INA223EVM files
into a folder labeled INA223EVM (for example, C:\INA223EVM) on your hard drive.
After the files are extracted, navigate to the INA223EVM folder you created on your hard drive. Locate the
setup.exe file and run it to start the installation. The INA223 software installer file opens to begin the
installation process, as shown in Figure 11.
Figure 11. Software Install Window
12
INA223EVM User’s Guide and Software Tutorial
SBOU125–June 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
www.ti.com
INA223EVM Software Setup
After the install begins, the user is given the choice of selecting the directory to install the program, usually
defaulting to C:\Program Files\INA223\ and C:\Program Files\National Instruments\. Following this option,
two license agreements are presented that must be accepted, as shown in Figure 12.
Figure 12. Software License Agreement
After accepting the Texas Instruments and National Instruments license agreements, the progress bar
opens and shows the installation of the software, as shown in Figure 13. After the installation process is
complete, click Finish.
Figure 13. Software Install Progress
13
SBOU125–June 2012
INA223EVM User’s Guide and Software Tutorial
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
INA223EVM Software Overview
www.ti.com
5
INA223EVM Software Overview
This section describes how to use the INA223EVM software. The software operation contains a two-step
process: configuration and operation.
5.1 Starting the INA223EVM Software
To start the INA223 software, go to the Windows Start menu, select All Programs, and then select the
INA223EVM program. Figure 14 illustrates how the software should appear if the INA223EVM is
functioning properly.
Figure 14. INA223EVM Software Interface
Figure 15 shows the error that appears if the computer cannot communicate with the EVM. In the event
you receive this error, first ensure that the USB cable is properly connected on both ends. This error can
also occur if you connect the USB cable to your PC before the SM-USB-DIG Platform is connected to the
EVM board. Another possible source for this error is a problem with the computer USB human interface
device driver. Make sure that the device is recognized when the USB cable is plugged in, indicated by a
Windows-generated confirmation sound.
Figure 15. Communication Error with SM-USB-DIG Platform
14
INA223EVM User’s Guide and Software Tutorial
SBOU125–June 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
www.ti.com
INA223EVM Software Overview
5.2 Configuring the INA223 Software
The next steps of this user’s guide describes how to configure the software and hardware for different
configurations.
5.2.1
I2C Address Selection
The INA223 has a flexible I2C address configuration that allows for multiple devices to be on the same I2C
lines. By moving the A0 address on jumpers JMP1 and JMP2 to either GND, VS, SDA or SCL, the INA223
can be changed to four different I2C addresses, as shown in Table 4.
Table 4. INA223 I2C Address Configuration
A0
GND
VS
Address
1000000
1000001
1000010
1000011
SDA
SCL
Figure 16 shows how to configure the I2C addresses. Click on the I2C Address Select button (shown in the
red box) to select how the hardware is configured on the EVM. If the correct address is not selected, the
INA223 cannot communicate with the software.
Figure 16. Setting the A0 Address
15
SBOU125–June 2012
INA223EVM User’s Guide and Software Tutorial
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
INA223EVM Software Overview
www.ti.com
5.2.2
Output Mode
The output mode configuration allows the user to toggle between different output signals generated from
the INA223, and is shown in the red box of Figure 17. The four options available for output mode are:
Shunt Voltage, Bus Voltage, Supply Power, and Load Power.
Figure 17. Configuring the Output Mode
The two power output modes of the INA223EVM is used to select whether the signal representing the
power being supplied by the power supply or the power being consumed by the load is made available at
the output pin. When the Supply Power option is selected, the VBUS measurement is taken internally at the
VIN+ pin of the INA223 and combined with the VSHUNT measurement to calculate the power being supplied.
The Load Power option operates in a similar manner to the Supply Power option, except that the VBUS
measurement is taken internally at the VIN– pin of the INA223. The power being consumeed by the load
is found by taking the VBUS measurement from the VIN– pin. The Supply Power and Load Power results
are very similar with the exception being that the Load Power option removes the power being dissipated
across the shunt resistor from the result. At high current shunt gains, the differences between Load Power
and Supply Power are negligible. At low current shunt gains, the power dissipated across the sense
resistor can result in a noticeable difference between these two results.
16
INA223EVM User’s Guide and Software Tutorial
SBOU125–June 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
www.ti.com
INA223EVM Software Overview
It is important to note that valid bus voltage and shunt voltage measurements must be within the linear
range of the device in order for the INA223 to correctly calculate power using Equation 1.
POWER = VOUT / PowerGAIN × RSHUNT
(1)
(2)
Where VOUT is calculated based on Equation 2:
VOUT = VCM × VSENSE × PowerGAIN
and PowerGAIN valuse are shown in Table 5.
Table 5. Power Gain Values
Bus Voltage Gain
Shunt Voltage Gain
PowerGAIN
0.667
4.267
10
1/10
1/10
1/10
1/5
20
128
300
20
1.333
8.533
20
1/5
128
300
20
1/5
2/5
2.667
17.067
40
2/5
128
300
2/5
The remaining two configurations, Bus Voltage and Shunt Voltage, measure the bus voltages at the VIN-
pin and the shunt voltage developed directly across the shunt resistor, respectively. The actual output
voltage of either measurement is based on the input voltage multiplied by the corresponding gain settings,
as shown in sections Section 5.2.3 and Section 5.2.4.
NOTE: For maximum accuracy, select a gain that gives a full-scale voltage, just below the maximum
output voltage.
17
SBOU125–June 2012
INA223EVM User’s Guide and Software Tutorial
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
INA223EVM Software Overview
www.ti.com
5.2.3
Bus Voltage Gain
The Bus Voltage Gain field allows the user to select the gain that the bus voltage is multiplied by. It is
important to choose a value that places the output voltage within the linear output range of the device.
Failure to ensure that the outputs are within the linear range of the device can result in inaccurate results.
Figure 18. Configuring the Bus Voltage Gain
Current Shunt Voltage Gain
5.2.4
The Current Shunt Voltage Gain field is used to select the device shunt voltage gain setting. It is important
to choose a value that places the output voltage within the linear output range of the device. Failure to
ensure that the outputs are within the linear range of the device can result in inaccurate results.
Figure 19. Configuring the Current Shunt Voltage Gain
18
INA223EVM User’s Guide and Software Tutorial
SBOU125–June 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
www.ti.com
INA223EVM Software Overview
5.3 Using the INA223 Software
5.3.1
Register Table
The register table (shown by the red box in Figure 20) contains information on the internal registers of the
INA223 registers. Each register can be changed on a bit-by-bit basis to allow the user to have total control
of the part, outside the general functionality of the graphical user interface (GUI). Most of this functionality
is displayed in the Configuration Register; however, by selecting the appropriate register and clicking on
the Help w Reg button (shown in Figure 20), the individual use of each bit in each register can be
diagnosed.
Figure 20. Register Table
19
SBOU125–June 2012
INA223EVM User’s Guide and Software Tutorial
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
INA223EVM Software Overview
www.ti.com
5.3.2
Auto-Write and DVDD Voltage
The INA223EVM software allows for customization of the board level voltage, regulated by the SM-USB-
DIG. Select either +3.3V or +5V for the operating voltage of the chip, as shown in the upper red box in
Figure 21.
Figure 21. Auto-Write, Power, and Voltage Controls
The software also includes an Auto-Write feature (as shown in the lower red box in Figure 21). Auto-Write
is enabled by default, and automatically updates the register table whenever a change is made. When this
feature is enabled, the Write all Reg button serves little purpose, and is only used as an alternative for
when this button is disabled.
20
INA223EVM User’s Guide and Software Tutorial
SBOU125–June 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
www.ti.com
INA223EVM Software Overview
5.3.3
Example Hardware Calculator
The Example Hardware Calculator tab allows the user to simulate the analog results of the INA223EVM.
By adjusting the controls on this page, and entering inputs for Vin+ (V), Vin- (V), and Rshunt, the
approximate values for Vout (V) and Power (W) can be estimated. Note that the appropriate output mode
must be selected to ensure accurate results, and that no limitations of the device are violated in the Error
field.
This calculator is used to help ensure that the physical output and settings are operating correctly. The
EVM and device digital communication interface are only designed to configure the device settings. There
is no analog readback available with this EVM. This means that the output voltages shown on this
calculator tab in the software are calculated results based on the parameters entered and not
representative of the measurements of the actual device.
Figure 22. Example Hardware Calculator
21
SBOU125–June 2012
INA223EVM User’s Guide and Software Tutorial
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
INA223EVM Documentation
www.ti.com
6
INA223EVM Documentation
This section contains the complete bill of materials, schematic diagram, and PCB layout for the
INA223EVM. Documentation information for the SM-USB-DIG Platform can be found in the SM-USB-DIG
Platform User’s Guide (SBOU058), available at the TI web site at http://www.ti.com.
6.1 Bill of Materials
Table 6 lists the bill of materials for the INA223 Test Board.
Table 6. Bill of Materials
Digikey
Part Number
Manufacturer
Part Number
Ref Des
R1, R2
R5
Description
Manufacturer
RES 10K OHM 1/10W 5% 0603 SMD
RES 300 OHM 1/10W 5% 0603 SMD
RES 0.0 OHM 1/10W 0603 SMD
CAP TANTALUM 4.7UF 35V 10% SM
CAP CER .10UF 25V X7R 10% 0603
LED GREEN WIDE ANGLE 0603 SMD
INA223
Stackpole Electronics
Panasonic
RMCF0603JT10K0CT-ND
P300GCT-ND
RMCF0603JT10K0
ERJ-3GEYJ301V
RMCF0603ZT0R00
TAJC475K035RNJ
C1608X7R1E104K
LNJ3W0C83RA
R3, R4
C2
Stackpole Electronics
AVX Corp
RMCF0603ZT0R00CT-ND
478-1717-1-ND
C3, C4
D1
TDK Corp
445-1316-1-ND
Panasonic
P14140CT-ND
U1
Texas Instruments
Samtec
Jumpers All
Test Points All
T3
CONN HEADER 50POS .100" SGL GOLD
PC TEST POINT COMPACT SMT
3Block Terminal 3.5mm
SAM1029-50-ND
5016KCT-ND
ED2636-ND
TSW-150-07-G-S
5016
Keystone Electronics
On Shore Technology Inc
On Shore Technology Inc
3M
OSTTE030161
ED555/2DS
T1, T2
Bumpons
H1
2Block Terminal 3.5mm
ED1514-ND
BUMPON .50X.14 BLACK
SJ5012-0-ND
ED8850-ND
SJ-5012 (BLACK)
851-93-10-20-001000
CONN SOCKET RT ANG 1POS .050
Mill-Max Manufacturing
22
INA223EVM User’s Guide and Software Tutorial
SBOU125–June 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
www.ti.com
INA223EVM Documentation
6.2 Schematic
Figure 23 shows the schematic for the INA223EVM board.
6
5
4
3
2
1
REVISION RECORD
LTR
ECO NO:
APPROVED:
DATE:
Power Jumper
Test Points
DVDD GND
A0
SDA
SCL
VIN+ VIN- VOUT
VS_EXT
JMP3
JUMP3
2
DVDD
D
D
+
C2
0.1uF
C1
4.7uF
VS_DIG
U1
Terminal Blocks
1
2
3
4
5
10
9
Address Select
VIN+
VIN-
VIN-
VIN+
VIN-2 VIN+2
T1
8
7
6
A0
A0
SDA
SCL
GND
VS
A0
SDA
SCL
1
GND
2
DVDD
VOUT
SCL
DVDD
VOUT
VS_EXT
JMP1
JMP2
TBLOCK2X_SMALL
JUMP3
JUMP3
INA223
2
2
T3
C
C
1
GND
2
SDA
SCL
3
SDA
GND
TBLOCK3X_SMALL
H1
1
SCL
I2C_SCK
CTL/MEAS4
I2C_SDA
CTL/MEAS5
SPI_DOUT
VDUT
R3
1
1
2
2
2
VIN-
T2
0
1
2
3
SDA
C3
DNP
4
R4
TBLOCK2X_SMALL
VIN+
5
0
6
VS_DIG
7
SPI_CLK
GND
8
B
B
9
SPI_CS
Pull-up Resistors
LED
10
SPI_DN
R1
D1
1
2
SCL
DVDD
DVDD
R5
DVDD
SM_DIG
1
2
10k
R2
300
2
1
SDA
10k
COMPANY:
TITLE:
Texas Instruments
INA223
DRAWN:
DATED:
DATED:
DATED:
DATED:
Ben Robbins
A
A
CHECKED:
CODE:
SIZE:
DRAWING NO:
REV:
QUALITY CONTROL:
RELEASED:
B
SCALE:
SHEET:
1
OF
1
Figure 23. INA223EVM Board Schematic
23
SBOU125–June 2012
INA223EVM User’s Guide and Software Tutorial
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
INA223EVM Documentation
www.ti.com
6.3 PCB Component Layout
Figure 24 shows the layout of the components for the INA223EVM PCB.
Figure 24. INA223EVM PCB Component Layout
24
INA223EVM User’s Guide and Software Tutorial
SBOU125–June 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Evaluation Board/Kit Important Notice
Texas Instruments (TI) provides the enclosed product(s) under the following conditions:
This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES
ONLY and is not considered by TI to be a finished end-product fit for general consumer use. Persons handling the product(s) must have
electronics training and observe good engineering practice standards. As such, the goods being provided are not intended to be complete
in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including product safety and environmental
measures typically found in end products that incorporate such semiconductor components or circuit boards. This evaluation board/kit does
not fall within the scope of the European Union directives regarding electromagnetic compatibility, restricted substances (RoHS), recycling
(WEEE), FCC, CE or UL, and therefore may not meet the technical requirements of these directives or other related directives.
Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/kit may be returned within 30 days from
the date of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SELLER TO BUYER
AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all claims
arising from the handling or use of the goods. Due to the open construction of the product, it is the user’s responsibility to take any and all
appropriate precautions with regard to electrostatic discharge.
EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY
INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
TI currently deals with a variety of customers for products, and therefore our arrangement with the user is not exclusive.
TI assumes no liability for applications assistance, customer product design, software performance, or infringement of patents or
services described herein.
Please read the User’s Guide and, specifically, the Warnings and Restrictions notice in the User’s Guide prior to handling the product. This
notice contains important safety information about temperatures and voltages. For additional information on TI’s environmental and/or
safety programs, please contact the TI application engineer or visit www.ti.com/esh.
No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or
combination in which such TI products or services might be or are used.
FCC Warning
This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES
ONLY and is not considered by TI to be a finished end-product fit for general consumer use. It generates, uses, and can radiate radio
frequency energy and has not been tested for compliance with the limits of computing devices pursuant to part 15 of FCC rules, which are
designed to provide reasonable protection against radio frequency interference. Operation of this equipment in other environments may
cause interference with radio communications, in which case the user at his own expense will be required to take whatever measures may
be required to correct this interference.
EVM Warnings and Restrictions
It is important to operate this EVM within the input voltage range of 0 V to 26 V and the output voltage range of 0 V to 5.5 V.
Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM. If there are questions
concerning the input range, please contact a TI field representative prior to connecting the input power.
Applying loads outside of the specified output range may result in unintended operation and/or possible permanent damage to the EVM.
Please consult the EVM User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the load specification,
please contact a TI field representative.
During normal operation, some circuit components may have case temperatures greater than +25°C. The EVM is designed to operate
properly with certain components above +25°C as long as the input and output ranges are maintained. These components include but are
not limited to linear regulators, switching transistors, pass transistors, and current sense resistors. These types of devices can be identified
using the EVM schematic located in the EVM User's Guide. When placing measurement probes near these devices during operation,
please be aware that these devices may be very warm to the touch.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Audio
Applications
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
www.ti.com/security
Medical
Logic
Security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense www.ti.com/space-avionics-defense
microcontroller.ti.com
www.ti-rfid.com
Video and Imaging
www.ti.com/video
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
相关型号：
©2020 ICPDF网 联系我们和版权申明