INA122U/2K5 [TI]
单电源、微功耗仪表放大器 | D | 8;型号: | INA122U/2K5 |
厂家: | TEXAS INSTRUMENTS |
描述: | 单电源、微功耗仪表放大器 | D | 8 放大器 仪表 光电二极管 仪表放大器 |
文件: | 总15页 (文件大小:340K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
INA122
®
INA122
INA122
Single Supply, MicroPower
INSTRUMENTATION AMPLIFIER
APPLICATIONS
● PORTABLE, BATTERY OPERATED
FEATURES
● LOW QUIESCENT CURRENT: 60µA
SYSTEMS
● WIDE POWER SUPPLY RANGE
Single Supply: 2.2V to 36V
● INDUSTRIAL SENSOR AMPLIFIER:
Bridge, RTD, Thermocouple
Dual Supply: –0.9/+1.3V to ±18V
● PHYSIOLOGICAL AMPLIFIER:
● COMMON-MODE RANGE TO (V–)–0.1V
● RAIL-TO-RAIL OUTPUT SWING
ECG, EEG, EMG
● MULTI-CHANNEL DATA ACQUISITION
● LOW OFFSET VOLTAGE: 250µV max
● LOW OFFSET DRIFT: 3µV/°C max
● LOW NOISE: 60nV/√Hz
DESCRIPTION
● LOW INPUT BIAS CURRENT: 25nA max
● 8-PIN DIP AND SO-8 SURFACE-MOUNT
The INA122 is a precision instrumentation amplifier
for accurate, low noise differential signal acquisition.
Its two-op-amp design provides excellent performance
with very low quiescent current, and is ideal for
portable instrumentation and data acquisition systems.
The INA122 can be operated with single power sup-
plies from 2.2V to 36V and quiescent current is a mere
60µA. It can also be operated from dual supplies. By
utilizing an input level-shift network, input common-
mode range extends to 0.1V below negative rail (single
supply ground).
V+
7
INA122
3
8
+
VIN
6
VO
+
–
V
O = (VIN – VIN) G
100kΩ
25kΩ
A single external resistor sets gain from 5V/V to
10000V/V. Laser trimming provides very low offset
voltage (250µV max), offset voltage drift (3µV/°C
max) and excellent common-mode rejection.
200k
RG
G = 5 +
25kΩ
RG
Package options include 8-pin plastic DIP and SO-8
surface-mount packages. Both are specified for the
–40°C to +85°C extended industrial temperature range.
1
2
–
VIN
100kΩ
5
Ref
4
V–
International Airport Industrial Park
•
Mailing Address: PO Box 11400, Tucson, AZ 85734
FAXLine: (800) 548-6133 (US/Canada Only)
• Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111 • Twx: 910-952-1111
Internet: http://www.burr-brown.com/
•
•
Cable: BBRCORP
•
Telex: 066-6491
•
FAX: (520) 889-1510
•
Immediate Product Info: (800) 548-6132
©1997 Burr-Brown Corporation
PDS-1388B
Printed in U.S.A. October, 1997
SBOS069
SPECIFICATIONS
At TA = +25°C, VS = +5V, RL = 20kΩ connected to VS/2, unless otherwise noted.
INA122P, U
TYP
INA122PA, UA
TYP
PARAMETER
CONDITIONS
MIN
MAX
MIN
MAX
UNITS
INPUT
Offset Voltage, RTI
vs Temperature
vs Power Supply (PSRR)
Input Impedance
Safe Input Voltage
±100
±1
±250
±3
±150
✻
±500
±5
µV
µV/°C
µV/V
Ω || pF
V
VS = +2.2V to +36V
10
1010 || 3
30
✻
✻
100
RS = 0
(V–)–0.3
(V–)–40
0
(V+)+0.3
(V+)+40
3.4
✻
✻
✻
✻
✻
✻
RS = 10kΩ
V
Common-Mode Voltage Range
Common-Mode Rejection
V
VCM = 0V to 3.4V
83
96
76
90
dB
INPUT BIAS CURRENT
vs Temperature
–10
±40
±1
–25
✻
✻
✻
✻
–50
nA
pA/°C
nA
Offset Current
±2
±5
vs Temperature
±40
pA/°C
GAIN
G = 5 to 10k
✻
✻
✻
✻
✻
✻
✻
V/V
V/V
Gain Equation
Gain Error
G = 5 + 200kΩ/RG
G = 5
G = 5
±0.05
5
±0.1
10
±0.15
✻
%
vs Temperature
Gain Error
ppm/°C
%
G = 100
±0.3
±0.5
±1
vs Temperature
Nonlinearity
G = 100
±25
±100
✻
ppm/°C
%
G = 100, VO = –14.85V to +14.9V
±0.005
±0.012
±0.024
NOISE (RTI)
Voltage Noise, f = 1kHz
f = 100Hz
60
100
110
2
✻
✻
✻
✻
✻
✻
nV/√Hz
nV/√Hz
nV/√Hz
µVp-p
f = 10Hz
fB = 0.1Hz to 10Hz
Current Noise, f = 1kHz
fB = 0.1Hz to 10Hz
80
2
fA/√Hz
pAp-p
OUTPUT
Voltage, Positive
Negative
VS = ±15V
VS = ±15V
(V+)–0.1 (V+)–0.05
✻
✻
✻
✻
✻
✻
V
V
(V–)+0.15 (V–)+0.1
Short-Circuit Current
Capacitive Load Drive
Short-Circuit to Ground
+3/–30
1
mA
nF
FREQUENCY RESPONSE
Bandwidth, –3dB
G = 5
120
✻
✻
✻
✻
✻
✻
✻
✻
kHz
kHz
kHz
V/µs
µs
G = 100
G = 500
5
0.9
Slew Rate
+0.08/–0.16
Settling Time, 0.01%
G = 5
G = 100
350
450
1.8
3
µs
G = 500
ms
Overload Recovery
50% Input Overload
µs
POWER SUPPLY
Voltage Range, Single Supply
Dual Supplies
+2.2
+5
60
+36
±18
85
✻
✻
✻
✻
✻
✻
✻
✻
V
V
–0.9/+1.3
Current
IO = 0
µA
TEMPERATURE RANGE
Specification
–40
–55
–55
+85
+85
✻
✻
✻
✻
✻
✻
°C
°C
°C
Operation
Storage
+125
Thermal Resistance, θJA
8-Pin DIP
150
150
✻
✻
°C/W
°C/W
SO-8 Surface-Mount
✻ Specification same as INA122P, INA122U.
The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes
no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change
without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant
any BURR-BROWN product for use in life support devices and/or systems.
®
2
INA122
PIN CONFIGURATION
ELECTROSTATIC
DISCHARGE SENSITIVITY
Top View
8-Pin DIP, SO-8
This integrated circuit can be damaged by ESD. Burr-Brown
recommends that all integrated circuits be handled with ap-
propriate precautions. Failure to observe proper handling and
installation procedures can cause damage.
RG
1
2
3
4
8
7
6
5
RG
V+
VO
Ref
–
VIN
+
VIN
ESD damage can range from subtle performance degradation
to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric
changes could cause the device not to meet its published
specifications.
V–
ABSOLUTE MAXIMUM RATINGS(1)
Supply Voltage, V+ to V– .................................................................... 36V
Signal Input Terminals, Voltage(2) ....................... (V–)–0.3V to (V+)+0.3V
Current(2) ...................................................... 5mA
Output Short Circuit ................................................................. Continuous
Operating Temperature ................................................. –40°C to +125°C
Storage Temperature..................................................... –55°C to +125°C
Lead Temperature (soldering, 10s) ............................................... +300°C
NOTES: (1) Stresses above these ratings may cause permanent damage.
(2) Input terminals are internally diode-clamped to the power supply rails.
Input signals that can exceed the supply rails by more than 0.3V should be
current-limited to 5mA or less.
PACKAGE INFORMATION
PACKAGE DRAWING
PRODUCT
PACKAGE
NUMBER(1)
INA122PA
INA122P
8-Pin DIP
8-Pin DIP
006
006
INA122UA
INA122U
SO-8 Surface Mount
SO-8 Surface Mount
182
182
NOTE: (1) For detailed drawing and dimension table, see end of data sheet, or
Appendix C of Burr-Brown IC Data Book.
®
3
INA122
TYPICAL PERFORMANCE CURVES
At TA = +25°C and VS = ±5V, unless otherwise noted.
GAIN vs FREQUENCY
70
COMMON-MODE REJECTION vs FREQUENCY
110
100
90
80
70
60
50
40
30
20
10
0
G = 1000
60
50
G = 100
40
G = 1000
G = 100
G = 5
30
20
10
0
G = 20
G = 5
–10
100
1k
10k
Frequency (Hz)
100k
1M
1M
15
1
10
100
1k
10k
100k
Frequency (Hz)
POSITIVE POWER SUPPLY REJECTION
vs FREQUENCY
NEGATIVE POWER SUPPLY REJECTION
vs FREQUENCY
100
80
60
40
20
0
100
80
60
40
20
0
G = 500
G = 500
G = 100
G = 100
G = 5
G = 5
100k
10
100
1k
10k
1
10
100
1k
10k
100k
Frequency (Hz)
Frequency (Hz)
INPUT COMMON-MODE RANGE
vs OUTPUT VOLTAGE, VS = ±15V, G = 5
INPUT COMMON-MODE VOLTAGE
vs OUTPUT VOLTAGE, VS = ±5V, G = 5
15
10
5
5
4
3
VS = ±5V
2
VS = +5V/0V
VREF = 2.5V
+15V
+
VD/2
–
1
VO
0
+
–
0
VD/2
Ref
+
–1
–2
–3
–4
–5
VREF = 0V
VCM
–5
–10
–15
–15V
2
–15
–10
–5
0
5
10
–5
–4 –3
–2
–1
0
1
2
3
4
5
Output Voltage (V)
Output Voltage (V)
®
4
INA122
TYPICAL PERFORMANCE CURVES (CONT)
At TA = +25°C and VS = ±5V, unless otherwise noted.
VOLTAGE and CURRENT NOISE DENSITY
vs FREQUENCY (RTI)
SETTLING TIME vs GAIN
10
1000
100
10
10V Step
1
0.01%
VN
0.1%
IN
0.1
1
10
100
1k
1
10
100
1k
10k
Gain (V/V)
Frequency (Hz)
INPUT-REFERRED OFFSET VOLTAGE WARM-UP
QUIESCENT CURRENT vs TEMPERATURE
10
8
80
Turn-on time ≤ 1ms. Settling time to
final value depends on Gain—see
settling time.
6
60
40
20
0
4
2
(Noise)
0
–2
–4
–6
–8
–10
0
1
2
3
4
5
6
7
8
9
10
–75
–50
–25
0
25
50
75
100
125
Time After Turn-On (ms)
Temperature (°C)
OUTPUT VOLTAGE SWING
vs OUTPUT CURRENT
TOTAL HARMONIC DISTORTION+NOISE
vs FREQUENCY
V+
(V+)–1
(V+)–2
(V–)+2
(V–)+1
V–
1
0.1
Sourcing Current
G = 100
0.01
0.001
G = 5
RL = ∞
RL = 25kΩ
Sinking Current
0
5
10
15
20
25
10
100
1k
10k
Output Current (mA)
Frequency (Hz)
®
5
INA122
TYPICAL PERFORMANCE CURVES (CONT)
At TA = +25°C and VS = ±5V, unless otherwise noted.
SMALL-SIGNAL STEP RESPONSE
G = 5
SMALL-SIGNAL STEP RESPONSE
G = 100
50µs/div
100µs/div
INPUT-REFERRED NOISE VOLTAGE
0.1Hz to 10Hz
LARGE-SIGNAL STEP RESPONSE
G = 5
500ms/div
50µs/div
®
6
INA122
offset adjustment. Figure 2 shows an optional circuit for
trimming the output offset voltage. The voltage applied to
the Ref terminal is added to the output signal. An op amp
buffer is used to provide low impedance at the Ref terminal
to preserve good common-mode rejection.
APPLICATION INFORMATION
Figure 1 shows the basic connections required for operation
of the INA122. Applications with noisy or high impedance
power supplies may require decoupling capacitors close to
the device pins.
The output is referred to the output reference (Ref) terminal
which is normally grounded. This must be a low-impedance
connection to ensure good common-mode rejection. A resis-
tance of 10Ω in series with the Ref pin will cause a typical
device to degrade to approximately 80dB CMR.
–
VIN
V+
VO
RG
INA122
Ref
100µA
1/2 REF200
+
VIN
SETTING THE GAIN
Gain of the INA122 is set by connecting a single external
resistor, RG, as shown:
100Ω
100Ω
10kΩ
OPA336
±10mV
Adjustment Range
200kΩ
(1)
G = 5 +
RG
Commonly used gains and RG resistor values are shown in
Figure 1.
100µA
1/2 REF200
The 200kΩ term in equation 1 comes from the internal metal
film resistors which are laser trimmed to accurate absolute
values. The accuracy and temperature coefficient of these
resistors are included in the gain accuracy and drift specifi-
cations of the INA122.
V–
FIGURE 2. Optional Trimming of Output Offset Voltage.
The stability and temperature drift of the external gain
setting resistor, RG, also affects gain. RG’s contribution to
gain accuracy and drift can be directly inferred from the gain
equation (1).
INPUT BIAS CURRENT RETURN PATH
The input impedance of the INA122 is extremely high—
approximately 1010Ω. However, a path must be provided for
the input bias current of both inputs. This input bias current
is approximately –10nA (current flows out of the input
terminals). High input impedance means that this input bias
current changes very little with varying input voltage.
OFFSET TRIMMING
The INA122 is laser trimmed for low offset voltage and
offset voltage drift. Most applications require no external
V+
0.1µF
DESIRED GAIN
(V/V)
RG
(Ω)
NEAREST 1%
RG VALUE
7
5
10
20
NC
40k
NC
40.2k
13.3k
4420
2100
1020
402
200
100
40.2
20
INA122
3
8
+
13.33k
4444
2105
1026
404
201
100.3
40
VIN
50
6
A1
200kΩ
RG
100
200
500
1000
2000
5000
10000
G = 5 +
100kΩ
25kΩ
+
–
VO = (VIN – VIN) G
25kΩ
+
RG
20
Load
VO
NC: No Connection.
–
1
2
A2
–
VIN
100kΩ
5
Also drawn in simplified form:
Ref
4
+
3
8
VIN
0.22µF
6
Single Supply
VO
INA122
RG
1
2
Ref
–
5
VIN
V–
Dual Supply
FIGURE 1. Basic Connections.
®
7
INA122
Input circuitry must provide a path for this input bias current
for proper operation. Figure 3 shows various provisions for an
input bias current path. Without a bias current path, the inputs
will float to a potential which exceeds the common-mode
range of the INA122 and the input amplifiers will saturate.
INPUT PROTECTION
The inputs of the INA122 are protected with internal diodes
connected to the power supply rails (Figure 4). These diodes
will clamp the applied signal to prevent it from damaging the
input circuitry. If the input signal voltage can exceed the
power supplies by more than 0.3V, the input signal current
should be limited to less than 5mA to protect the internal
clamp diodes. This can generally be done with a series input
resistor. Some signal sources are inherently current-limited
and do not require limiting resistors.
If the differential source resistance is low, the bias current
return path can be connected to one input (see the thermo-
couple example in Figure 3). With higher source impedance,
using two equal resistors provides a balanced input with
possible advantages of lower input offset voltage due to bias
current and better high-frequency common-mode rejection.
INPUT COMMON-MODE RANGE
The common-mode range for some common operating con-
ditions is shown in the typical performance curves. The
INA122 can operate over a wide range of power supply and
VREF configurations, making it impractical to provide a
comprehensive guide to common-mode range limits for all
possible conditions. The most commonly overlooked over-
load condition occurs by attempting to exceed the output
swing of A2, an internal circuit node that cannot be mea-
sured. Calculating the expected voltages at A2’s output (see
equation in Figure 4) provides a check for the most common
overload conditions.
Microphone,
Hydrophone
etc.
INA122
47kΩ
47kΩ
Thermocouple
INA122
The design of A1 and A2 are identical and their outputs can
swing to within approximately 100mV of the power supply
rails, depending on load conditions. When A2’s output is
saturated, A1 can still be in linear operation, responding to
changes in the non-inverting input voltage. This may give the
appearance of linear operation but the output voltage is invalid.
10kΩ
INA122
A single supply instrumentation amplifier has special design
considerations. Using commonly available single-supply op
amps to implement the two-op amp topology will not yield
equivalent performance. For example, consider the condition
where both inputs of common single-supply op amps are
Center-tap provides
bias current return.
FIGURE 3. Providing an Input Common-Mode Current Path.
V+
+
V
IN + 0.5V
+
A1
VO
VIN
(3)
(8)
100kΩ
25kΩ
V–
V+
RG
25kΩ
RG
–
+
–
)
25kΩ
VO2 = 1.25VIN – (VIN – VIN
+ 0.6V
(1)
(Voltages are referred to VREF
)
(V–) + 0.1V ≤ V02 ≤ (V+) –0.1V
V02
A2
–
VIN + 0.5V
100kΩ
–
VIN
Ref
(2)
V–
FIGURE 4. INA122 Simplified Circuit Diagram.
®
8
INA122
equal to 0V. The outputs of both A1 and A2 must be 0V. But
any small positive voltage applied to VIN+ requires that A2’s
output must swing below 0V, which is clearly impossible
without a negative power supply.
Operation at very low supply voltage requires careful atten-
tion to ensure that the common-mode voltage remains within
its linear range.
To achieve common-mode range that extends to single-
supply ground, the INA122 uses precision level-shifting
buffers on its inputs. This shifts both inputs by approxi-
mately +0.5V, and through the feedback network, shifts A2’s
output by approximately +0.6V. With both inputs and VREF
at single-supply, A2’s output is well within its linear range.
LOW QUIESCENT CURRENT OPERATION
The INA122 maintains its low quiescent current (60µA)
while the output is within linear operation (up to 200mV
from the supply rails). When the input creates a condition
that overdrives the output into saturation, quiescent current
increases. With VO overdriven into the positive rail, the
quiescent current increases to approximately 400µA. Like-
wise, with VO overdriven into the negative rail (single
supply ground) the quiescent current increases to approxi-
mately 200µA.
+
A positive VIN causes A2’s output to swing below 0.6V.
As a result of this input level-shifting, the voltages at pin 1
and pin 8 are not equal to their respective input terminal
voltages (pins 2 and 3). For most applications, this is not
important since only the gain-setting resistor connects to
these pins.
OUTPUT CURRENT RANGE
Output sourcing and sinking current values versus the output
voltage ranges are shown in the typical performance curves.
The positive and negative current limits are not equal.
Positive output current sourcing will drive moderate to high
load impedances. Battery operation normally requires the
careful management of power consumption to keep load
impedances very high throughout the design.
LOW VOLTAGE OPERATION
The INA122 can be operated on a single power supply as
low as +2.2V (or a total of +2.2V on dual supplies). Perfor-
mance remains excellent throughout the power supply range
up to +36V (or ±18V). Most parameters vary only slightly
throughout this supply voltage range—see typical perfor-
mance curves.
+5V
REF200
200µA
(60µA)
≈ 200mV
+
VIN
3
8
7
1kΩ
VO = 0.1V to 4.9V
VO
V
CM ≈ 100mV
6
RG
INA122
1
2
5
Ref(1)
4
NOTE: (1) To accomodate bipolar input signals,
VREF can be offset to a positive voltage. Output
voltage is then referred to the voltage applied to Ref.
–
VIN
FIGURE 5. Micropower Single Supply Bridge Amplifier.
V+
+5V
8
Load
1
IL
2.5A
VREF
+
6
VIN
3
8
G = 100
1kΩ
D
Serial Data
7
Shunt
RS
0.02Ω
2
3
6
ADS7816
12-Bit A/D
50mV
RG
INA122
+IN
–IN
1
2
5
0.47µF
5
7
–
4
CS
Chip Select
Clock
VIN
CLK
4
Differential measurement
avoids ground loop errors.
FIGURE 6. Single-Supply Current Shunt Measurement.
®
9
INA122
PACKAGE OPTION ADDENDUM
www.ti.com
14-Oct-2022
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
INA122P
ACTIVE
ACTIVE
PDIP
PDIP
P
P
8
8
50
50
RoHS & Green
RoHS & Green
Call TI
N / A for Pkg Type
N / A for Pkg Type
-40 to 85
INA122P
Samples
Samples
INA122PA
Call TI
Call TI
Call TI
Call TI
Call TI
INA122P
A
INA122PAG4
INA122U
ACTIVE
ACTIVE
ACTIVE
ACTIVE
PDIP
SOIC
SOIC
SOIC
P
D
D
D
8
8
8
8
50
75
RoHS & Green
RoHS & Green
N / A for Pkg Type
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
INA122P
A
Samples
Samples
Samples
Samples
INA
122U
INA122U/2K5
INA122UA
2500 RoHS & Green
75 RoHS & Green
INA
122U
INA
122U
A
INA122UA/2K5
ACTIVE
SOIC
D
8
2500 RoHS & Green
Call TI
Level-3-260C-168 HR
INA
122U
A
Samples
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
14-Oct-2022
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
3-Jun-2022
TAPE AND REEL INFORMATION
REEL DIMENSIONS
TAPE DIMENSIONS
K0
P1
W
B0
Reel
Diameter
Cavity
A0
A0 Dimension designed to accommodate the component width
B0 Dimension designed to accommodate the component length
K0 Dimension designed to accommodate the component thickness
Overall width of the carrier tape
W
P1 Pitch between successive cavity centers
Reel Width (W1)
QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE
Sprocket Holes
Q1 Q2
Q3 Q4
Q1 Q2
Q3 Q4
User Direction of Feed
Pocket Quadrants
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
INA122U/2K5
SOIC
SOIC
D
D
8
8
2500
2500
330.0
330.0
12.4
12.4
6.4
6.4
5.2
5.2
2.1
2.1
8.0
8.0
12.0
12.0
Q1
Q1
INA122UA/2K5
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
3-Jun-2022
TAPE AND REEL BOX DIMENSIONS
Width (mm)
H
W
L
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
INA122U/2K5
SOIC
SOIC
D
D
8
8
2500
2500
356.0
356.0
356.0
356.0
35.0
35.0
INA122UA/2K5
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
3-Jun-2022
TUBE
T - Tube
height
L - Tube length
W - Tube
width
B - Alignment groove width
*All dimensions are nominal
Device
Package Name Package Type
Pins
SPQ
L (mm)
W (mm)
T (µm)
B (mm)
INA122P
INA122PA
INA122PAG4
INA122U
P
P
P
D
D
PDIP
PDIP
PDIP
SOIC
SOIC
8
8
8
8
8
50
50
50
75
75
506
506
13.97
13.97
13.97
8
11230
11230
11230
3940
4.32
4.32
4.32
4.32
4.32
506
506.6
506.6
INA122UA
8
3940
Pack Materials-Page 3
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2022, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明