INA2134-EP [TI]
AUDIO DIFFERENTIAL LINE RECEIVER 0dB (G = 1); 音频差动线路接收器0分贝（G = 1 ）
| 型号： | INA2134-EP |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | AUDIO DIFFERENTIAL LINE RECEIVER 0dB (G = 1) |
| 文件： | 总18页 (文件大小：620K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
INA2134-EP
www.ti.com
SBOS595C –MARCH 2012–REVISED MARCH 2012
AUDIO DIFFERENTIAL LINE RECEIVER 0dB (G = 1)
Check for Samples: INA2134-EP
1
FEATURES
•
•
•
•
•
•
•
•
•
Single and Dual Versions
SUPPORTS DEFENSE, AEROSPACE,
AND MEDICAL APPLICATIONS
Low Distortion: 0.0005% at f = 1 kHz
High Slew Rate: 14 V/ms
•
•
•
•
Controlled Baseline
One Assembly/Test Site
One Fabrication Site
Fast Settling Time: 3 ms to 0.01%
Wide Supply Range: ±4 V to ±18 V
Low Quiescent Current: 3.1 mA max
High CMRR: 90 dB
Available in Military (–55°C/125°C)
Temperature Range(1)
•
•
•
Extended Product Life Cycle
Extended Product-Change Notification
Product Traceability
Fixed Gain = 0 dB (1V/V)
Dual 14-Pin SOIC Package
APPLICATIONS
D PACKAGE
(TOP VIEW)
•
•
•
•
•
•
•
•
Audio Differential Line Receiver
Summing Amplifier
1
2
3
4
5
6
7
14
13
12
11
10
9
NC
–In A
+In A
V–
Ref A
Out A
Sense A
V+
Unity-Gain Inverting Amplifier
Psuedoground Generator
Instrumentation Building Block
Current Shunt Monitor
A
Voltage-Controlled Current Source
Ground Loop Eliminator
+In B
–In B
NC
Sense B
Out B
Ref B
B
8
NC = No Connection
(1) Additional temperature ranges available - contact factory
DESCRIPTION
The INA2134 is a differential line receiver consisting of high performance op amps with onchip precision
resistors. The device is fully specified for high performance audio applications and has excellent ac
specifications, including low distortion (0.0005% at 1 kHz) and high slew rate (14 V/ms), assuring good dynamic
response. In addition, wide output voltage swing and high output drive capability allow use in a wide variety of
demanding applications. The dual version features completely independent circuitry for lowest crosstalk and
freedom from interaction, even when overdriven or overloaded.
The INA2134 on-chip resistors are laser trimmed for accurate gain and optimum common-mode rejection.
Furthermore, excellent TCR tracking of the resistors maintains gain accuracy and common-mode rejection over
temperature. Operation is guaranteed from ±4 V to ±18 V (8-V to 36-V total supply).
The INA2134 comes in a 14-pin SOIC surface-mount package and is specified for operation over the military
temperature range, –55°C to 125°C.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Copyright © 2012, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
INA2134-EP
SBOS595C –MARCH 2012–REVISED MARCH 2012
www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
ORDERING INFORMATION(1)
ORDERABLE PART
TA
PACKAGE
TOP-SIDE MARKING
VID NUMBER
TRANSPORT MEDIA
NUMBER
INA2134MDREP
INA2134MDEP
V62/12613-01XE
V62/12613-02XE
Tape and Reel, large
Tube
–55°C to 125°C
SOIC-14 – D
INA2134M
(1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
V+
11
25kW
25kW
2
12
13
–In A
Sense A
A
Out A
25kW
25kW
25kW
3
6
14
10
+In A
–In B
Ref A
25kW
Sense B
9
8
Out B
Ref B
B
25kW
25kW
5
+In B
INA2134
4
V–
ABSOLUTE MAXIMUM RATINGS(1)
over operating free-air temperature range (unless otherwise noted)
VALUE
40
UNIT
V
Supply voltage, V+ to V-
Input voltage range
±80
V
Output short-circuit (to ground)(2)
Continuous
Operating temperature
-55 to 125
-65 to 150
150
°C
°C
°C
°C
V
Storage temperature
Junction temperature
Lead temperature (soldering, 10 s)
300
ESD Rating
Human Body Model (HBM)
Machine Model (MM)
500
100
V
(1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) One channel per package.
2
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA2134-EP
INA2134-EP
www.ti.com
SBOS595C –MARCH 2012–REVISED MARCH 2012
THERMAL INFORMATION
INA2134
THERMAL METRIC(1)
D
14 PINS
73.1
UNITS
θJA
θJC
θJB
ψJT
ψJB
Junction-to-ambient thermal resistance(2)
Junction-to-case thermal resistance
31.1
Junction-to-board thermal resistance(3)
Junction-to-top characterization parameter(4)
Junction-to-board characterization parameter(5)
27.6
°C/W
3.2
27.3
xxx
(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
(2) The junction-to-ambient thermal resistance under natural convection is obtained in a simulation on a JEDEC-standard, high-K board, as
specified in JESD51-7, in an environment described in JESD51-2a.
(3) The junction-to-board thermal resistance is obtained by simulating in an environment with a ring cold plate fixture to control the PCB
temperature, as described in JESD51-8.
(4) The junction-to-top characterization parameter, ψJT, estimates the junction temperature of a device in a real system and is extracted
from the simulation data for obtaining θJA, using a procedure described in JESD51-2a (sections 6 and 7).
(5) The junction-to-board characterization parameter, ψJB, estimates the junction temperature of a device in a real system and is extracted
from the simulation data for obtaining θJA , using a procedure described in JESD51-2a (sections 6 and 7).
ELECTRICAL CHARACTERISTICS
At TA = 25°C, VS = ±18 V, RL = 2 kΩ, and Ref pin connected to Ground (unless otherwise noted).
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
AUDIO PERFORMANCE
Total harmonic distortion + noise, f = 1 kHz
Noise floor(1)
Headroom(1)
VIN = 10 Vrms
20 kHz BW
0.0005
-100
23
%
dBu
dBu
THD+N < 1%
FREQUENCY RESPONSE
Small-signal bandwidth
Slew rate
3.1
14
2
MHz
V/µs
µs
Settling time:
0.1%
10-V step, CL = 100 pF
10-V step, CL = 100 pF
50% overdrive
0.01%
3
µs
Overload recovery time
3
µs
Channel separation (dual), f = 1 kHz
OUTPUT NOISE VOLTAGE(2)
f = 20 Hz to 20 kHz
117
dB
7
µVrms
f = 1 kHz
52
nV/√Hz
OFFSET VOLTAGE(3)
Input offset voltage
VCM = 0 V
±100
±2
±1000
±60
µV
vs Temperature
-55°C to 125°C
µV/°C
vs Power
supply
VS = ±4 V to ±18 V, -55°C to 125°C
±5
µV/V
INPUT
Common-mode voltage range:
Positive
VO = 0 V
VO = 0 V
2(V+) – 5
2(V-) + 5
2(V+) – 4
2(V-) + 2
V
V
Negative
Differential voltage range
Common-mode rejection
Impedance:(4)
See Typical Curve
VCM = ±31 V, RS = 0 Ω
74
72
90
85
50
50
dB
dB
kΩ
kΩ
VCM = ±31 V, RS = 0 Ω, -55°C to 125°C
Differential
Common-mode
(1) dBu = 20log (Vrms/0.7746).
(2) Includes effects of amplifier’s input current noise and thermal noise contribution of resistor network.
(3) Includes effects of amplifier’s input bias and offset currents.
(4) 25-kΩ resistors are ratio matched, but have ±25% absolute value.
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Link(s): INA2134-EP
INA2134-EP
SBOS595C –MARCH 2012–REVISED MARCH 2012
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
At TA = 25°C, VS = ±18 V, RL = 2 kΩ, and Ref pin connected to Ground (unless otherwise noted).
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
GAIN
Initial
Error
1
±0.02
±2
V/V
%
VO = –16 V to 16 V
VO = –16 V to 16 V, -55°C to 125°C
VO = –16 V to 16 V
±0.1
±3.5
vs Temperature
Nonlinearity
%
0.0001
%
OUTPUT
Voltage output:
Positive
Negative
Positive
Negative
(V+) – 2
(V-) + 2
(V+) – 1.8
(V-) + 1.6
(V+) – 2.1
(V-) + 1.8
±60
V
V
Specified temperature range
Specified temperature range
(V+) – 2.45
(V-) + 2.45
V
V
Current limit, continuous to common
Capacitive load (stable operation)
POWER SUPPLY
mA
pF
500
Rated voltage
±18
V
V
Voltage range
±4
±18
±2.9
±3.1
IO = 0 A
±2.4
±2.7
mA
mA
Quiescent current (per amplifier)
IO = 0 A, -55°C to 125°C
TEMPERATURE RANGE
Specified temperature range
Operating temperature range
Storage temperature range
–55
–55
–65
125
125
150
°C
°C
°C
xxx
1000000
100000
10000
1000
Electromigration Fail Mode
Wirebond Life
125
130
135
140
145
150
Continuous T (°C)
J
A. See datasheet for absolute maximum and minimum recommended operating conditions.
B. Silicon operating life design goal is 10 years at 105°C junction temperature (does not include package interconnect
life).
C. The predicted operating lifetime vs. junction temperature is based on reliability modeling using electromigration as the
dominant failure mechanism affecting device wearout for the specific device process and design characterisitics.
Figure 1. INA2134 Electromigration Fail Mode/Wirebond Life Derating Chart
4
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA2134-EP
INA2134-EP
www.ti.com
SBOS595C –MARCH 2012–REVISED MARCH 2012
TYPICAL CHARACTERISTICS
At TA = 25°C, VS = ±18 V (unless otherwise noted).
TOTAL HARMONIC DISTORTION+NOISE
DIM INTERMODULATION DISTORTION
vs OUTPUT AMPLITUDE
vs FREQUENCY
1
5
1
BW = 100kHz
VO = 10Vrms
0.1
0.010
0.1
RL = 2kW, 600W
RL = 100kW
RL = 2kW
0.001
0.010
0.001
RL = 600W
0.0001
20
100
1k
10k 20k
–10
20
1
–5
0
5
10
15
20
25
Frequency (Hz)
Output Amplitude (dBu)
HEADROOM - TOTAL HARMONIC DISTORTION+NOISE
vs OUTPUT AMPLITUDE
HARMONIC DISTORTION PRODUCTS
vs FREQUENCY
1
0.1
0.01
0.001
f = 1kHz
RL = 600W,
RL = 600W,
2nd Harmonic
3rd Harmonic
RL = 2kW,
2nd Harmonic
0.010
0.001
0.0001
0.0001
RL = 600W
(
noise limited)
VO = 1Vrms
RL = 2kW,
0.00001
0.000001
3rd Harmonic
RL = 2kW,
100kW
0
5
10
15
20
25
30
100
1k
10k 20k
Output Amplitude (dBu)
Frequency (Hz)
OUTPUT VOLTAGE NOISE SPECTRAL DENSITY
vs FREQUENCY
OUTPUT NOISE VOLTAGE
vs NOISE BANDWIDTH
10k
1k
100
10
1
100
10
0.1
1
10
100
1k
10k
100k
1M
10
100
1k
10k
100k
Frequency (Hz)
Frequency (Hz)
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Link(s): INA2134-EP
INA2134-EP
SBOS595C –MARCH 2012–REVISED MARCH 2012
www.ti.com
TYPICAL CHARACTERISTICS (continued)
At TA = 25°C, VS = ±18 V (unless otherwise noted).
GAIN vs FREQUENCY
10
COMMON-MODE REJECTION vs FREQUENCY
100
80
60
40
20
0
0
–10
–20
–30
1k
10k
100k
1M
10M
1k
10k
100k
Frequency (Hz)
1M
Frequency (Hz)
POWER SUPPLY REJECTION vs FREQUENCY
CHANNEL SEPARATION vs FREQUENCY
120
100
80
60
40
20
0
130
120
110
100
90
RL = 100kW
–PSR
RL = 2kW
+PSR
100
1k
10k
100k
1M
20
100
1k
10k 20k
Frequency (Hz)
Frequency (Hz)
INPUT COMMON-MODE VOLTAGE RANGE
vs OUTPUT VOLTAGE
MAXIMUM OUTPUT VOLTAGE vs FREQUENCY
40
30
20
10
0
40
30
VS
= 18V
20
10
0
–10
–20
–30
–40
–50
VREF = 0V
RL = 2kW
100
1k
10k
100k
1M
10M
–20
–15
–10
–5
0
5
10
15
20
Frequency (Hz)
Output Voltage (V)
6
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA2134-EP
INA2134-EP
www.ti.com
SBOS595C –MARCH 2012–REVISED MARCH 2012
TYPICAL CHARACTERISTICS (continued)
At TA = 25°C, VS = ±18 V (unless otherwise noted).
SLEW RATE vs TEMPERATURE
QUIESCENT CURRENT vs TEMPERATURE
4
16
14
12
10
8
–SR
+SR
3
2
1
0
–75
–50
–25
0
25
50
75
100
125
–75
–50
–25
0
25
50
75
100
125
Temperature (°C)
Temperature (°C)
SHORT-CIRCUIT CURRENT vs TEMPERATURE
QUIESCENT CURRENT vs SUPPLY VOLTAGE
80
3
2
1
0
60
40
+ISC
20
0
–20
–40
–60
–80
–ISC
–75
–50
–25
0
25
50
75
100
125
4
6
8
10
12
14
16
18
Temperature (°C)
Supply Voltage (V)
OFFSET VOLTAGE
PRODUCTION DISTRIBUTION
25
Typical Production
Distribution of
Packaged Units.
20
15
10
5
0
Offset Voltage (µV)
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Link(s): INA2134-EP
INA2134-EP
SBOS595C –MARCH 2012–REVISED MARCH 2012
www.ti.com
TYPICAL CHARACTERISTICS (continued)
At TA = 25°C, VS = ±18 V (unless otherwise noted).
SMALL-SIGNAL OVERSHOOT
vs LOAD CAPACITANCE
OUTPUT VOLTAGE SWING vs OUTPUT CURRENT
17
70
60
50
40
30
20
10
0
16
–55°C
15
25°C
14
125°C
13
85°C
12
–12
85°C
125°C
–13
–14
–15
–16
–17
RL = 2kW
25°C
–55°C
100mV Step
0
400
800
1200
1600 2000
0
20
40
60
80
100
Load Capacitance (pF)
Output Current (mA)
LARGE-SIGNAL STEP RESPONSE
CL = 500pF
SMALL-SIGNAL STEP RESPONSE
CL = 100pF
CL = 500pF
1ms/div
1ms/div
8
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA2134-EP
INA2134-EP
www.ti.com
SBOS595C –MARCH 2012–REVISED MARCH 2012
APPLICATION INFORMATION
Basic Connection
Figure 2 shows the basic connections required for operation of the INA2134. Decoupling capacitors are strongly
recommended in applications with noisy or high impedance power supplies. The capacitors should be placed
close to the device pins as shown in Figure 2. All circuitry is completely independent in the dual version assuring
lowest crosstalk and normal behavior when one amplifier is overdriven or short-circuited.
As shown in Figure 2, the differential input signal is connected to pins 2 and 3. The source impedances
connected to the inputs must be nearly equal to assure good common mode rejection. A 10-Ω mismatch in
source impedance will degrade the common-mode rejection of a typical device to approximately 74 dB. If the
source has a known impedance mismatch, an additional resistor in series with the opposite input can be used to
preserve good common-mode rejection.
Do not interchange pins 1 and 3 or pins 2 and 5, even though nominal resistor values are equal. These resistors
are laser trimmed for precise resistor ratios to achieve accurate gain and highest CMR. Interchanging these pins
would not provide specified performance.
V–
V+
1µF
1µF
4
7
INA2134
R1
R2
25kW
25kW
–In
2
5
6
V2
V
OUT = V3 – V2
R3
R4
25kW
25kW
+In
1
3
V3
Figure 2. Precision Difference Amplifier (Basic Power Supply and Signal Connections)
Audio Performance
The INA2134 was designed for enhanced ac performance. Very low distortion, low noise, and wide bandwidth
provide superior performance in high quality audio applications. Laser-trimmed matched resistors provide
optimum common-mode rejection (typically 90 dB), especially when compared to circuits implemented with an
operational amplifier and discrete precision resistors. In addition, high slew rate (14 V/µs) and fast settling time
(3 ms to 0.01%) ensure good dynamic performance.
The INA2134 has excellent distortion characteristics. THD+Noise is below 0.002% throughout the audio
frequency range. Up to approximately 10-kHz distortion is below the measurement limit of commonly used test
equipment. Furthermore, distortion remains relatively flat over its wide output voltage swing range (approximately
1.7 V from either supply).
Offset Voltage Trim
The INA2134 is laser trimmed for low offset voltage and drift. Most applications require no external offset
adjustment. Figure 3 shows an optional circuit for trimming the output offset voltage. The output is referred to the
output reference terminal (pin 1), which is normally grounded. A voltage applied to the Ref terminal will be
summed with the output signal. This can be used to null offset voltage as shown in Figure 3. The source
impedance of a signal applied to the Ref terminal should be less than 10 Ω to maintain good common-mode
rejection.
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Link(s): INA2134-EP
INA2134-EP
SBOS595C –MARCH 2012–REVISED MARCH 2012
www.ti.com
INA2134
R2
R1
2
5
6
V2
VO
1ꢀ
R3
W
3
V3
R4
+15V
1
VO = V3 – V2
499k
W
Offset Adjustment
Range = 3ꢀꢀ0V
1ꢀꢀk
W
1ꢀ
W
–15V
Figure 3. Offset Adjustment
Other Applications
The difference amplifier is a highly versatile building block that is useful in a wide variety of applications. See the
INA105 data sheet (SBOS145) for additional applications ideas, including:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Current Receiver with Compliance to Rails
Precision Unity-Gain Inverting Amplifier
±10-V Precision Voltage Reference
±5- Precision Voltage Reference
Precision Unity-Gain Buffer
Precision Average Value Amplifier
Precision G = 2 Amplifier
Precision Summing Amplifier
Precision G = 1/2 Amplifier
Precision Bipolar Offsetting
Precision Summing Amplifier with Gain
Instrumentation Amplifier Guard Drive Generator
Precision Summing Instrumentation Amplifier
Precision Absolute Value Buffer
Precision Voltage-to-Current Converter with Differential Inputs
Differential Input Voltage-to-Current Converter for Low IOUT
Isolating Current Source
Differential Output Difference Amplifier
Isolating Current Source with Buffering Amplifier for Greater Accuracy
Window Comparator with Window Span and Window Center Inputs
Precision Voltage-Controlled Current Source with Buffered Differential Inputs and Gain
Digitally Controlled Gain of ±1 Amplifier
10
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA2134-EP
INA2134-EP
www.ti.com
SBOS595C –MARCH 2012–REVISED MARCH 2012
INA2134
2
5
6
V0 = V1 + V2
1
3
V1
V2
Figure 4. Precision Summing Amplifier
INA2134
2
5
6
1
–In
3
6
VO
BUF634
3
+In
Figure 5. Boosting Output Current
INA2134
V1
1/2
2
5
6
1
–In
OPA2134
R2
R1
V0
0utput
R2
1/2
OPA2134
3
V2
+In
VO = (1 + 2R2/R1) (V2 –V1)
Figure 6. High Input Impedance Instrumentation Amplifier
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Link(s): INA2134-EP
PACKAGE OPTION ADDENDUM
www.ti.com
2-Apr-2012
PACKAGING INFORMATION
Status (1)
Eco Plan (2)
MSL Peak Temp (3)
Samples
Orderable Device
Package Type Package
Drawing
Pins
Package Qty
Lead/
Ball Finish
(Requires Login)
INA2134MDREP
V62/12613-01XE
ACTIVE
ACTIVE
SOIC
SOIC
D
D
14
14
2500
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF INA2134-EP :
Catalog: INA2134
•
NOTE: Qualified Version Definitions:
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
2-Apr-2012
Catalog - TI's standard catalog product
•
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
INA2134MDREP
SOIC
D
14
2500
330.0
16.4
6.5
9.0
2.1
8.0
16.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SOIC 14
SPQ
Length (mm) Width (mm) Height (mm)
367.0 367.0 38.0
INA2134MDREP
D
2500
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Audio
Applications
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
www.ti.com/security
Medical
Logic
Security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense www.ti.com/space-avionics-defense
microcontroller.ti.com
www.ti-rfid.com
Video and Imaging
www.ti.com/video
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
相关型号：
©2020 ICPDF网 联系我们和版权申明