INA2181A1IDSQT [TI]
26V、双通道、双向、350kHz 电流感应放大器 | DSQ | 10 | -40 to 125;型号: | INA2181A1IDSQT |
厂家: | TEXAS INSTRUMENTS |
描述: | 26V、双通道、双向、350kHz 电流感应放大器 | DSQ | 10 | -40 to 125 放大器 |
文件: | 总58页 (文件大小:2002K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Support &
Community
Product
Folder
Order
Now
Tools &
Software
Technical
Documents
INA181, INA2181, INA4181
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
INAx181 双向低侧和高侧电压输出
电流感应放大器
1 特性
3 说明
1
•
•
•
共模范围 (VCM):–0.2V 至 +26V
INA181、INA2181 和 INA4181 (INAx181) 电流检测放
大器专为经成本优化的 解决方案而设计。这些器件是
一系列双向电流检测放大器(也称为电流分流监控
器),可在独立于电源电压的 –0.2V 至 +26V 范围内
的共模电压中感测电流检测电阻器上的压降。INAx181
系列集成有一个匹配的电阻器增益网络,具有四个固定
增益器件选项:20V/V、50V/V、100V/V 或 200V/V。
该匹配增益电阻器网络可最大限度地减小增益误差并降
低温漂。
高带宽:350kHz(A1 器件)
偏移电压:
–
–
±150µV(最大值),VCM = 0V
±500µV(最大值),VCM = 12V
•
•
•
输出压摆率:2V/µs
双向电流感应功能
精度:
–
–
±1% 增益误差(最大值)
1µV/°C 温漂(最大值)
这些器件由 2.7V 至 5.5V 单电源供电。单通道 INA181
消耗的最大电源电流为 260µA;而双通道 INA2181 消
耗的最大电源电流为 500µA,四通道 INA4181 消耗的
最大电源电流为 900µA。
•
增益选项:
–
–
–
–
20V/V(A1 器件)
50V/V(A2 器件)
100V/V(A3 器件)
200V/V(A4 器件)
INA181 可提供 6 引脚 SOT-23 封装。INA2181 可提
供 10 引脚 VSSOP 封装。INA4181 可提供 20 引脚
TSSOP 封装。所有器件选项的额定扩展工作温度范围
均为 –40°C 至 +125°C。
•
瞬态电流:最大为 260µA (INA181)
2 应用
器件信息(1)
•
•
•
•
•
•
电机控制
电池监控
电源管理
照明控制
过流检测
光伏逆变器
器件型号
INA181
封装
SOT-23 (6)
封装尺寸(标称值)
2.90mm × 1.60mm
3.00mm × 3.00mm
6.50mm × 4.40mm
INA2181
INA4181
VSSOP (10)
TSSOP (20)
(1) 如需了解所有可用封装,请参阅产品说明书末尾的封装选项附
录。
典型应用电路
Bus Voltage, VCM
Up To 26 V
Power Supply, VS
2.7 V to 5.5 V
CBYPASS
0.1 µF
RSENSE
Load
INA4181 (quad-channel)
INA2181 (dual-channel)
INA181 (single-channel)
VS
Microcontroller
INœ
œ
OUT
ADC
+
IN+
REF
GND
Copyright © 2017, Texas Instruments Incorporated
1
本文档旨在为方便起见,提供有关 TI 产品中文版本的信息,以确认产品的概要。 有关适用的官方英文版本的最新信息,请访问 www.ti.com,其内容始终优先。 TI 不保证翻译的准确
性和有效性。 在实际设计之前,请务必参考最新版本的英文版本。
English Data Sheet: SBOS793
INA181, INA2181, INA4181
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
www.ti.com.cn
目录
1
2
3
4
5
6
7
特性.......................................................................... 1
应用.......................................................................... 1
说明.......................................................................... 1
修订历史记录 ........................................................... 2
Device Comparison Table..................................... 4
Pin Configuration and Functions......................... 4
Specifications......................................................... 7
7.1 Absolute Maximum Ratings ..................................... 7
7.2 ESD Ratings.............................................................. 7
7.3 Recommended Operating Conditions....................... 7
7.4 Thermal Information.................................................. 7
7.5 Electrical Characteristics........................................... 8
7.6 Typical Characteristics.............................................. 9
Detailed Description ............................................ 16
8.1 Overview ................................................................. 16
8.2 Functional Block Diagrams ..................................... 16
8.3 Feature Description................................................. 18
8.4 Device Functional Modes........................................ 20
9
Application and Implementation ........................ 23
9.1 Application Information............................................ 23
9.2 Typical Application .................................................. 30
10 Power Supply Recommendations ..................... 32
10.1 Common-Mode Transients Greater Than 26 V .... 32
11 Layout................................................................... 33
11.1 Layout Guidelines ................................................. 33
11.2 Layout Example .................................................... 33
12 器件和文档支持 ..................................................... 36
12.1 器件支持................................................................ 36
12.2 文档支持................................................................ 36
12.3 相关链接................................................................ 36
12.4 接收文档更新通知 ................................................. 36
12.5 社区资源................................................................ 36
12.6 商标....................................................................... 36
12.7 静电放电警告......................................................... 36
12.8 术语表 ................................................................... 36
13 机械、封装和可订购信息....................................... 37
8
4 修订历史记录
Changes from Revision E (July 2018) to Revision F
Page
•
•
•
已添加 new paragraph regarding phase reversal to end of Input Differential Overload section .......................................... 21
已更改 Figure 57 to fix pin number typos ............................................................................................................................. 33
已更改 Figure 58 to fix pin number typos ............................................................................................................................ 34
Changes from Revision D (March 2018) to Revision E
Page
•
已更改 将 INAx180 实例更改为 INAx181(拼写错误).......................................................................................................... 1
Changes from Revision C (December 2017) to Revision D
Page
•
•
•
•
已更改 将 INA4181 器件从预览更改为生产数据(有效)....................................................................................................... 1
已添加 new Figure 25 for INA4181....................................................................................................................................... 12
已添加 new Figure 28 for INA4181....................................................................................................................................... 12
已添加 "other" to first sentence after Figure 49 to clarify channel connection in Summing Multiple Currents section ........ 27
Changes from Revision B (November 2017) to Revision C
Page
•
•
•
•
•
•
•
•
•
已更改 将 INA2181 器件从预览更改为生产数据(有效)....................................................................................................... 1
已添加 "Both Inputs" to Figure 21 title.................................................................................................................................. 11
已添加 new Figure 24 for INA2181....................................................................................................................................... 11
已添加 new Figure 25 placeholder for INA4181................................................................................................................... 12
已添加 new Figure 27 for INA2181....................................................................................................................................... 12
已添加 new Figure 28 placeholder for INA4181................................................................................................................... 12
已更改 Figure 29 and added "(A3 Devices)" to end of title .................................................................................................. 12
已添加 new Figure 38 for INA2181....................................................................................................................................... 14
已更改 "less than 150 μV" to "within ±150 μV" regarding offset voltage in Precise Low-Side Current Sensing section...... 19
2
版权 © 2017–2019, Texas Instruments Incorporated
INA181, INA2181, INA4181
www.ti.com.cn
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
•
•
•
•
•
•
已添加 text regarding RC filter and reference to application report to note at the bottom of Figure 45 .............................. 23
已删除 VS from Equation 3 .................................................................................................................................................. 24
已添加 equation and curve for f-3dB to Figure 48................................................................................................................... 25
已添加 new content to Summing Multiple Currents section and moved to Application Information section ........................ 27
已添加 new content to Detecting Leakage Currents section and moved to Application Information section....................... 28
已添加 new bullet to Layout Guidelines section .................................................................................................................. 33
Changes from Revision A (August 2017) to Revision B
Page
•
•
•
已添加 在产品说明书中添加了 INA4181 预览器件和相关内容 ............................................................................................... 1
已更改 design parameter name in Table 3 from "Accuracy" to "Current sensing error" for clarity ..................................... 30
已更改 "RMS" to "RSS" in reference to equation 7 ............................................................................................................. 31
Changes from Original (April 2017) to Revision A
Page
•
已添加 在产品说明书中添加了 INA2181 预览器件和相关内容 ............................................................................................... 1
Copyright © 2017–2019, Texas Instruments Incorporated
3
INA181, INA2181, INA4181
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
www.ti.com.cn
5 Device Comparison Table
PRODUCT
INA181A1
INA181A2
INA181A3
INA181A4
INA2181A1
INA2181A2
INA2181A3
INA2181A4
INA4181A1
INA4181A2
INA4181A3
INA4181A4
NUMBER OF CHANNELS
GAIN (V/V)
1
1
1
1
2
2
2
2
4
4
4
4
20
50
100
200
20
50
100
200
20
50
100
200
6 Pin Configuration and Functions
INA181: DBV Package
6-Pin SOT-23
Top View
OUT
GND
IN+
1
2
3
6
5
4
VS
REF
INœ
Not to scale
Pin Functions: INA181 (Single Channel)
PIN
TYPE
DESCRIPTION
NAME
NO.
GND
2
Analog
Ground
Current-sense amplifier negative input. For high-side applications, connect to load
side of sense resistor. For low-side applications, connect to ground side of sense
resistor.
IN–
IN+
4
3
Analog input
Current-sense amplifier positive input. For high-side applications, connect to bus-
voltage side of sense resistor. For low-side applications, connect to load side of
sense resistor.
Analog input
OUT
REF
VS
1
5
6
Analog output
Analog input
Analog
Output voltage
Reference input
Power supply, 2.7 V to 5.5 V
4
Copyright © 2017–2019, Texas Instruments Incorporated
INA181, INA2181, INA4181
www.ti.com.cn
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
INA2181: DGS Package
10-Pin VSSOP
INA4181: PW Package
20-Pin TSSOP
Top View
Top View
REF1
OUT1
INœ1
IN+1
VS
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
REF4
OUT4
INœ4
IN+4
GND
IN+3
INœ3
OUT3
REF3
NC
OUT1
INœ1
1
2
3
4
5
10
9
VS
OUT2
INœ2
IN+2
REF2
IN+1
GND
REF1
8
7
6
IN+2
INœ2
OUT2
REF2
NC
Not to scale
Not to scale
Pin Functions: INA2181 (Dual Channel) and INA4181 (Quad Channel)
PIN
INA2181
4
TYPE
DESCRIPTION
NAME
INA4181
GND
16
Analog
Ground
Current-sense amplifier negative input for channel 1. For high-side
IN–1
IN+1
IN–2
IN+2
IN–3
IN+3
IN–4
2
3
3
4
Analog input
Analog input
Analog input
Analog input
Analog input
Analog input
Analog input
applications, connect to load side of channel-1 sense resistor. For low-
side applications, connect to ground side of channel-1 sense resistor.
Current-sense amplifier positive input for channel 1. For high-side
applications, connect to bus-voltage side of channel-1 sense resistor. For
low-side applications, connect to load side of channel-1 sense resistor.
Current-sense amplifier negative input for channel 2. For high-side
applications, connect to load side of channel-2 sense resistor. For low-
side applications, connect to ground side of channel-2 sense resistor.
8
7
Current-sense amplifier positive input for channel 2. For high-side
applications, connect to bus-voltage side of channel-2 sense resistor. For
low-side applications, connect to load side of channel-2 sense resistor.
7
6
Current-sense amplifier negative input for channel 3. For high-side
applications, connect to load side of channel-3 sense resistor. For low-
side applications, connect to ground side of channel-3 sense resistor.
—
—
—
14
15
18
Current-sense amplifier positive input for channel 3. For high-side
applications, connect to bus-voltage side of channel-3 sense resistor. For
low-side applications, connect to load side of channel-3 sense resistor.
Current-sense amplifier negative input for channel 4. For high-side
applications, connect to load side of channel-4 sense resistor. For low-
side applications, connect to ground side of channel-4 sense resistor.
Current-sense amplifier positive input for channel 4. For high-side
applications, connect to bus-voltage side of channel-4 sense resistor. For
low-side applications, connect to load side of channel-4 sense resistor.
IN+4
NC
—
—
17
Analog input
—
NC denotes no internal connection. These pins can be left floating or
connected to any voltage between VS and ground.
10, 11
OUT1
OUT2
OUT3
OUT4
1
9
2
8
Analog output
Analog output
Analog output
Analog output
Channel 1 output voltage
Channel 2 output voltage
Channel 3 output voltage
Channel 4 output voltage
—
—
13
19
Copyright © 2017–2019, Texas Instruments Incorporated
5
INA181, INA2181, INA4181
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
www.ti.com.cn
Pin Functions: INA2181 (Dual Channel) and INA4181 (Quad Channel) (continued)
PIN
TYPE
DESCRIPTION
NAME
REF1
REF2
REF3
REF4
VS
INA2181
INA4181
5
6
1
9
Analog input
Analog input
Analog input
Analog input
Analog
Channel 1 reference voltage, 0 to VS
Channel 2 reference voltage, 0 to VS
Channel 3 reference voltage, 0 to VS
Channel 4 reference voltage, 0 to VS
Power supply pin, 2.7 V to 5.5 V
—
—
10
12
20
5
6
Copyright © 2017–2019, Texas Instruments Incorporated
INA181, INA2181, INA4181
www.ti.com.cn
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
7 Specifications
7.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1)
MIN
MAX
6
UNIT
Supply voltage, VS
V
Differential (VIN+) – (VIN–
Common-mode(3)
at REF pin
)
–26
26
Analog inputs, IN+, IN–(2)
V
GND – 0.3
GND – 0.3
GND – 0.3
26
Input voltage range
VS + 0.3
VS + 0.3
8
V
V
Output voltage
Maximum output current, IOUT
Operating free-air temperature, TA
Junction temperature, TJ
Storage temperature, Tstg
mA
°C
°C
°C
–55
–65
150
150
150
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) VIN+ and VIN– are the voltages at the IN+ and IN– pins, respectively.
(3) Input voltage at any pin can exceed the voltage shown if the current at that pin is limited to 5 mA.
7.2 ESD Ratings
VALUE
±3000
±1000
UNIT
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1)
Charged-device model (CDM), per JEDEC specification JESD22-C101(2)
V(ESD)
Electrostatic discharge
V
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
7.3 Recommended Operating Conditions
MIN
–0.2
2.7
NOM
12
MAX
UNIT
VCM
VS
Common-mode input voltage (IN+ and IN–)
Operating supply voltage
26
5.5
V
V
5
TA
Operating free-air temperature
–40
125
°C
7.4 Thermal Information
INA181
DBV (SOT-23)
6 PINS
198.7
INA2181
DGS (VSSOP)
10 PINS
177.3
INA4181
PW (TSSOP)
20 PINS
97.0
(1)
THERMAL METRIC
UNIT
RθJA
Junction-to-ambient thermal resistance
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
RθJC(top)
RθJB
120.9
68.7
37.7
52.3
98.4
48.3
ψJT
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
30.3
12.6
3.6
ψJB
52.0
96.9
47.9
RθJC(bot)
N/A
N/A
N/A
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
Copyright © 2017–2019, Texas Instruments Incorporated
7
INA181, INA2181, INA4181
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
www.ti.com.cn
7.5 Electrical Characteristics
at TA = 25°C, VS = 5 V, VREF = VS / 2, VIN+ = 12 V, and VSENSE = VIN+ – VIN– (unless otherwise noted)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
INPUT
VIN+ = 0 V to 26 V, VSENSE = 0 mV,
TA = –40°C to +125°C
Common-mode rejection ratio,
RTI
CMRR
84
100
dB
(1)
VSENSE = 0 mV
±100
±25
0.2
±500
±150
1
μV
μV
VOS
Offset voltage, RTI
VSENSE = 0 mV, VIN+ = 0 V
VSENSE = 0 mV, TA = –40°C to +125°C
dVOS/dT
PSRR
Offset drift, RTI
μV/°C
VS = 2.7 V to 5.5 V, VIN+ = 12 V,
VSENSE = 0 mV
Power-supply rejection ratio, RTI
±8
±40
μV/V
VSENSE = 0 mV, VIN+ = 0 V
VSENSE = 0 mV
-6
75
µA
µA
µA
IIB
Input bias current
Input offset current
IIO
VSENSE = 0 mV
±0.05
OUTPUT
A1 devices
A2 devices
A3 devices
A4 devices
20
50
V/V
V/V
V/V
V/V
G
Gain
100
200
VOUT = 0.5 V to VS – 0.5 V,
TA = –40°C to +125°C
EG
Gain error
±0.1%
±1%
20
Gain error vs temperature
Nonlinearity error
TA = –40°C to +125°C
VOUT = 0.5 V to VS – 0.5 V
No sustained oscillation
1.5
±0.01%
1
ppm/°C
nF
Maximum capacitive load
(2)
VOLTAGE OUTPUT
VSP
VSN
Swing to VS power-supply rail(3)
RL = 10 kΩ to GND, TA = –40°C to +125°C
RL = 10 kΩ to GND, TA = –40°C to +125°C
(VS) – 0.02
(VS) – 0.03
V
V
(VGND) +
0.0005
(VGND) +
0.005
Swing to GND(3)
FREQUENCY RESPONSE
A1 devices, CLOAD = 10 pF
A2 devices, CLOAD = 10 pF
A3 devices, CLOAD = 10 pF
A4 devices, CLOAD = 10 pF
350
210
150
105
2
kHz
kHz
kHz
kHz
V/µs
BW
Bandwidth
SR
Slew rate
NOISE, RTI(1)
Voltage noise density
POWER SUPPLY
40
195
356
690
nV/√Hz
VSENSE = 0 mV
INA181
260
300
µA
µA
µA
µA
µA
µA
VSENSE = 0 mV, TA = –40°C to +125°C
VSENSE = 0 mV
500
IQ
Quiescent current
INA2181
INA4181
VSENSE = 0 mV, TA = –40°C to +125°C
VSENSE = 0 mV
520
900
VSENSE = 0 mV, TA = –40°C to +125°C
1000
(1) RTI = referred-to-input.
(2) See 图 19.
(3) Swing specifications are tested with an overdriven input condition.
8
版权 © 2017–2019, Texas Instruments Incorporated
INA181, INA2181, INA4181
www.ti.com.cn
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
7.6 Typical Characteristics
at TA = 25°C, VS = 5 V, VREF = VS / 2, and VIN+ = 12 V (unless otherwise noted)
D002
D001
Input Offset Voltage (mV)
Input Offset Voltage (mV)
图 1. Input Offset Voltage Production Distribution A1
图 2. Input Offset Voltage Production Distribution A2
D003
D004
Input Offset Voltage (mV)
Input Offset Voltage (mV)
图 3. Input Offset Voltage Production Distribution A3
图 4. Input Offset Voltage Production Distribution A4
100
A1
A2
A3
A4
50
0
-50
-100
-50
-25
0
25
50
75
100
125
150
Temperature (èC)
D005
D006
Common-Mode Rejection Ratio (mV/V)
图 5. Offset Voltage vs Temperature
图 6. Common-Mode Rejection Production Distribution A1
版权 © 2017–2019, Texas Instruments Incorporated
9
INA181, INA2181, INA4181
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
www.ti.com.cn
Typical Characteristics (接下页)
at TA = 25°C, VS = 5 V, VREF = VS / 2, and VIN+ = 12 V (unless otherwise noted)
D007
D008
Common-Mode Rejection Ratio (mV/V)
Common-Mode Rejection Ratio (mV/V)
图 7. Common-Mode Rejection Production Distribution A2
图 8. Common-Mode Rejection Production Distribution A3
10
A1
A2
8
A3
A4
6
4
2
0
-2
-4
-6
-8
-10
-50
-25
0
25
50
75
100
125
150
Temperature (èC)
D010
D009
Common-Mode Rejection Ratio (mV/V)
图 10. Common-Mode Rejection Ratio vs Temperature
图 9. Common-Mode Rejection Production Distribution A4
D011
D012
Gain Error (%)
Gain Error (%)
图 11. Gain Error Production Distribution A1
图 12. Gain Error Production Distribution A2
版权 © 2017–2019, Texas Instruments Incorporated
10
INA181, INA2181, INA4181
www.ti.com.cn
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
Typical Characteristics (接下页)
at TA = 25°C, VS = 5 V, VREF = VS / 2, and VIN+ = 12 V (unless otherwise noted)
D013
D014
Gain Error (%)
Gain Error (%)
图 13. Gain Error Production Distribution A3
图 14. Gain Error Production Distribution A4
50
40
30
20
10
0
0.4
0.3
0.2
0.1
0
A1
A1
A2
A3
A4
A2
A3
A4
-0.1
-0.2
-0.3
-0.4
-10
-50
-25
0
25
50
75
100
125
150
10
100
1k
10k
100k
1M
10M
Temperature (èC)
Frequency (Hz)
D015
D016
图 15. Gain Error vs Temperature
图 16. Gain vs Frequency
120
100
80
60
40
20
0
140
120
100
80
A1
A2
A3
A4
60
40
20
0
10
100
1k
10k
100k
1M
10
100
1k
10k
100k
1M
10M
Frequency (Hz)
Frequency (Hz)
D017
D018
图 17. Power-Supply Rejection Ratio vs Frequency
图 18. Common-Mode Rejection Ratio vs Frequency
版权 © 2017–2019, Texas Instruments Incorporated
11
INA181, INA2181, INA4181
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
www.ti.com.cn
Typical Characteristics (接下页)
at TA = 25°C, VS = 5 V, VREF = VS / 2, and VIN+ = 12 V (unless otherwise noted)
VS
VS – 1
VS – 2
120
100
80
60
40
20
0
–40°C
25°C
125°C
GND + 2
GND + 1
GND
-20
0
5
10 15 20 25 30 35 40 45 50 55 60
Output Current (mA)
-5
0
5
10
15
20
25
30
Common-Mode Voltage (V)
D019
D020
Supply voltage = 5 V
图 19. Output Voltage Swing vs Output Current
图 20. Input Bias Current vs Common-Mode Voltage
120
100
80
60
40
20
0
80
79
78
77
76
75
74
73
72
71
70
-20
-5
0
5
10
15
20
25
30
-50
-25
0
25
50
75
100
125
150
Common-Mode Voltage (V)
Temperature (èC)
D021
D022
Supply voltage = 0 V
图 21. Input Bias Current vs Common-Mode Voltage (Both
图 22. Input Bias Current vs Temperature
Inputs, Shutdown)
380
375
370
365
360
355
350
345
340
210
205
200
195
190
185
180
-50
-25
0
25
50
75
100
125
150
-50
-25
0
25
50
75
100
125
150
Temperature (èC)
Temperature (èC)
D023
D023
图 23. Quiescent Current vs Temperature (INA181)
图 24. Quiescent Current vs Temperature (INA2181)
12
版权 © 2017–2019, Texas Instruments Incorporated
INA181, INA2181, INA4181
www.ti.com.cn
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
Typical Characteristics (接下页)
at TA = 25°C, VS = 5 V, VREF = VS / 2, and VIN+ = 12 V (unless otherwise noted)
710
705
700
695
690
685
680
675
670
665
660
655
650
400
350
300
250
200
150
-50
-25
0
25
50
75
100
125
150
-5
0
5
10
15
20
25
30
Temperature (èC)
Common-Mode Voltage (V)
D038
D031
图 25. Quiescent Current vs Temperature (INA4181)
图 26. IQ vs Common-Mode Voltage (INA181)
750
700
650
600
550
500
450
400
350
300
1450
1350
1250
1150
1050
950
850
750
650
550
-5
0
5
10
15
20
25
30
-5
0
5
10
15
20
25
30
Common-Mode Voltage (V)
Common-Mode Voltage (V)
D031
D039
图 27. IQ vs Common-Mode Voltage (INA2181)
图 28. IQ vs Common-Mode Voltage (INA4181)
100
80
70
60
50
40
30
20
10
10
Time (1 s/div)
100
1k
10k
100k
1M
Frequency (Hz)
D025
D024
图 30. 0.1-Hz to 10-Hz Voltage Noise (Referred-to-Input)
图 29. Input-Referred Voltage Noise vs Frequency
(A3 Devices)
版权 © 2017–2019, Texas Instruments Incorporated
13
INA181, INA2181, INA4181
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
www.ti.com.cn
Typical Characteristics (接下页)
at TA = 25°C, VS = 5 V, VREF = VS / 2, and VIN+ = 12 V (unless otherwise noted)
VCM
VOUT
Time (10 ms/div)
Time (25 ms/div)
D026
D027
80-mVPP input step
图 31. Step Response
图 32. Common-Mode Voltage Transient Response
Inverting Input
Output
Noninverting Input
Output
0 V
0 V
Time (250 ms/div)
Time (250 ms/div)
D028
D029
图 33. Inverting Differential Input Overload
图 34. Noninverting Differential Input Overload
Supply Voltage
Output Voltage
Supply Voltage
Output Voltage
0 V
0 V
Time (10
ms/div)
Time (100 ms/div)
D030
D032
图 35. Start-Up Response
图 36. Brownout Recovery
14
版权 © 2017–2019, Texas Instruments Incorporated
INA181, INA2181, INA4181
www.ti.com.cn
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
Typical Characteristics (接下页)
at TA = 25°C, VS = 5 V, VREF = VS / 2, and VIN+ = 12 V (unless otherwise noted)
140
130
120
110
100
90
1000
Ch1 onto Ch2
Ch2 onto Ch1
A1
A2
A3
A4
500
200
100
50
20
10
5
2
1
0.5
80
0.2
0.1
10
70
100
1k
10k
100k
1M
100
1k
10k
100k
1M
10M
Frequency (Hz)
Frequency (Hz)
D034
D033
图 38. Channel Separation vs Frequency (INA2181)
图 37. Output Impedance vs Frequency
版权 © 2017–2019, Texas Instruments Incorporated
15
INA181, INA2181, INA4181
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
www.ti.com.cn
8 Detailed Description
8.1 Overview
The INA181, INA2181, and INA4181 (INAx181) are 26-V common-mode, current-sensing amplifiers used in both
low-side and high-side configurations. These specially-designed, current-sensing amplifiers accurately measure
voltages developed across current-sensing resistors on common-mode voltages that far exceed the supply
voltage powering the device. Current can be measured on input voltage rails as high as 26 V, and the devices
can be powered from supply voltages as low as 2.7 V.
8.2 Functional Block Diagrams
VS
Single-Channel
TI Device
INœ
œ
OUT
+
IN+
REF
GND
图 39. INA181 Functional Block Diagram
VS
Dual-Channel
TI Device
INœ1
œ
OUT1
+
REF1
IN+1
INœ2
œ
OUT2
REF2
+
IN+2
GND
图 40. INA2181 Functional Block Diagram
16
版权 © 2017–2019, Texas Instruments Incorporated
INA181, INA2181, INA4181
www.ti.com.cn
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
Functional Block Diagrams (接下页)
VS
Quad-Channel
TI Device
INœ1
œ
OUT1
+
REF1
IN+1
INœ2
œ
OUT2
REF2
+
IN+2
INœ3
œ
OUT3
REF3
+
IN+3
INœ4
œ
OUT4
REF4
+
IN+4
GND
图 41. INA4181 Functional Block Diagram
版权 © 2017–2019, Texas Instruments Incorporated
17
INA181, INA2181, INA4181
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
www.ti.com.cn
8.3 Feature Description
8.3.1 High Bandwidth and Slew Rate
The INAx181 support small-signal bandwidths as high as 350 kHz, and large-signal slew rates of 2 V/µs. The
ability to detect rapid changes in the sensed current, as well as the ability to quickly slew the output, make the
INAx181 a good choice for applications that require a quick response to input current changes. One application
that requires high bandwidth and slew rate is low-side motor control, where the ability to follow rapid changing
current in the motor allows for more accurate control over a wider operating range. Another application that
requires higher bandwidth and slew rates is system fault detection, where the INAx181 are used with an external
comparator and a reference to quickly detect when the sensed current is out of range.
8.3.2 Bidirectional Current Monitoring
The INA181 senses current flow through a sense resistor in both directions. The bidirectional current-sensing
capability is achieved by applying a voltage at the REF pin to offset the output voltage. A positive differential
voltage sensed at the inputs results in an output voltage that is greater than the applied reference voltage;
likewise, a negative differential voltage at the inputs results in output voltage that is less than the applied
reference voltage. The output voltage of the current-sense amplifier is shown in 公式 1.
VOUT = ILOADì RSENSE ìGAIN + V
REF
where
•
•
•
•
ILOAD is the load current to be monitored.
RSENSE is the current-sense resistor.
GAIN is the gain option of the selected device.
VREF is the voltage applied to the REF pin.
(1)
8.3.3 Wide Input Common-Mode Voltage Range
The INAx181 support input common-mode voltages from –0.2 V to +26 V. Because of the internal topology, the
common-mode range is not restricted by the power-supply voltage (VS) as long as VS stays within the operational
range of 2.7 V to 5.5 V. The ability to operate with common-mode voltages greater or less than VS allow the
INAx181 to be used in high-side, as well as low-side, current-sensing applications, as shown in 图 42.
Bus Supply
œ0.2 V to +26 V
Direction of Positive
IN+
Current Flow
High-Side Sensing
RSENSE
Common-mode voltage (VCM
is bus-voltage dependent.
)
INœ
LOAD
Direction of Positive
Current Flow
IN+
Low-Side Sensing
Common-mode voltage (VCM
is always near ground and is
)
RSENSE
isolated from bus-voltage spikes.
INœ
图 42. High-Side and Low-Side Sensing Connections
18
版权 © 2017–2019, Texas Instruments Incorporated
INA181, INA2181, INA4181
www.ti.com.cn
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
Feature Description (接下页)
8.3.4 Precise Low-Side Current Sensing
When used in low-side current sensing applications the offset voltage of the INAx181 is within ±150 µV. The low
offset performance of the INAx181 has several benefits. First, the low offset allows these devices to be used in
applications that must measure current over a wide dynamic range. In this case, the low offset improves the
accuracy when the sensed currents are on the low end of the measurement range. Another advantage of low
offset is the ability to sense lower voltage drop across the sense resistor accurately, thus allowing a lower-value
shunt resistor. Lower-value shunt resistors reduce power loss in the current sense circuit, and help improve the
power efficiency of the end application.
The gain error of the INAx181 is specified to be within 1% of the actual value. As the sensed voltage becomes
much larger than the offset voltage, this voltage becomes the dominant source of error in the current sense
measurement.
8.3.5 Rail-to-Rail Output Swing
The INAx181 allow linear current sensing operation with the output close to the supply rail and GND. The
maximum specified output swing to the positive rail is 30 mV, and the maximum specified output swing to GND is
only 5 mV. In order to compare the output swing of the INAx181 to an equivalent operational amplifier (op amp),
the inputs are overdriven to approximate the open-loop condition specified in op amp data sheets. The current-
sense amplifier is a closed-loop system; therefore, the output swing to GND can be limited by the product of the
offset voltage and amplifier gain during unidirectional operation (VREF = 0 V).
For devices that have positive offset voltages, the swing to GND is limited by the larger of either the offset
voltage multiplied by the gain or the swing to GND specified in the Electrical Characteristics table.
For example, in an application where the INA181A4 (gain = 200 V/V) is used for low-side current sensing and the
device has an offset of 40 µV, the product of the device offset and gain results in a value of 8 mV, greater than
the specified negative swing value. Therefore, the swing to GND for this example is 8 mV. If the same device
has an offset of –40 µV, then the calculated zero differential signal is –8 mV. In this case, the offset helps
overdrive the swing in the negative direction, and swing performance is consistent with the value specified in the
Electrical Characteristics table.
The offset voltage is a function of the common-mode voltage as determined by the CMRR specification;
therefore, the offset voltage increases when higher common-mode voltages are present. The increase in offset
voltage limits how low the output voltage can go during a zero-current condition when operating at higher
common-mode voltages with VREF = 0 V . The typical limitation of the zero-current output voltage vs common-
mode voltage for each gain option is shown in 图 43.
0.06
A1
0.054
A2
A3
A4
0.048
0.042
0.036
0.03
0.024
0.018
0.012
0.006
0
0
2
4
6
8
10 12 14 16 18 20 22 24 26
Common Mode Voltage (V)
D033
图 43. Zero-Current Output Voltage vs Common-Mode Voltage
版权 © 2017–2019, Texas Instruments Incorporated
19
INA181, INA2181, INA4181
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
www.ti.com.cn
8.4 Device Functional Modes
8.4.1 Normal Mode
The INAx181 are in normal operation when the following conditions are met:
•
•
•
The power supply voltage (VS) is between 2.7 V and 5.5 V.
The common-mode voltage (VCM) is within the specified range of –0.2 V to +26 V.
The maximum differential input signal times gain plus VREF is less than VS minus the output voltage swing to
VS.
•
The minimum differential input signal times gain plus VREF is greater than the swing to GND (see the Rail-to-
Rail Output Swing section).
During normal operation, these devices produce an output voltage that is the gained-up representation of the
difference voltage from IN+ to IN– plus the reference voltage at VREF
.
8.4.2 Unidirectional Mode
These devices can be configured to monitor current flowing in one direction (unidirectional) or in both directions
(bidirectional) depending on how the REF pin is configured. The most common case is unidirectional where the
output is set to ground when no current is flowing by connecting the REF pin to ground, as shown in 图 44. When
the current flows from the bus supply to the load, the input signal across IN+ to IN– increases, and causes the
output voltage at the OUT pin to increase.
Bus Voltage
Power Supply, VS
2.7 V to 5.5 V
œ0.2 V to +26 V
CBYPASS
0.1 µF
RSENSE
Load
VS
Single-Channel
TI Device
INœ
OUT
œ
Output
+
IN+
REF
GND
图 44. Unidirectional Application
The linear range of the output stage is limited by how close the output voltage can approach ground under zero
input conditions. In unidirectional applications where measuring very low input currents is desirable, bias the REF
pin to a convenient value above 50 mV to get the output into the linear range of the device. To limit common-
mode rejection errors, buffer the reference voltage connected to the REF pin.
A less-frequently used output biasing method is to connect the REF pin to the power-supply voltage, VS. This
method results in the output voltage saturating at 200 mV less than the supply voltage when no differential input
signal is present. This method is similar to the output saturated low condition with no input signal when the REF
pin is connected to ground. The output voltage in this configuration only responds to negative currents that
develop negative differential input voltage relative to the device IN– pin. Under these conditions, when the
differential input signal increases negatively, the output voltage moves downward from the saturated supply
voltage. The voltage applied to the REF pin must not exceed VS.
20
版权 © 2017–2019, Texas Instruments Incorporated
INA181, INA2181, INA4181
www.ti.com.cn
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
Device Functional Modes (接下页)
8.4.3 Bidirectional Mode
The INAx181 are bidirectional, current-sense amplifiers capable of measuring currents through a resistive shunt
in two directions. This bidirectional monitoring is common in applications that include charging and discharging
operations where the current flowing through the resistor can change directions.
Bus Voltage
œ0.2 V to +26 V
Power Supply, VS
2.7 V to 5.5 V
CBYPASS
0.1 µF
RSENSE
Load
VS
Single-Channel
TI Device
Reference
Voltage
INœ
œ
OUT
REF
Output
+
IN+
+
œ
GND
图 45. Bidirectional Application
The ability to measure this current flowing in both directions is enabled by applying a voltage to the REF pin, as
shown in 图 45. The voltage applied to REF (VREF) sets the output state that corresponds to the zero-input level
state. The output then responds by increasing above VREF for positive differential signals (relative to the IN– pin)
and responds by decreasing below VREF for negative differential signals. This reference voltage applied to the
REF pin can be set anywhere between 0 V to VS. For bidirectional applications, VREF is typically set at mid-scale
for equal signal range in both current directions. In some cases, however, VREF is set at a voltage other than mid-
scale when the bidirectional current and corresponding output signal do not need to be symmetrical.
8.4.4 Input Differential Overload
If the differential input voltage (VIN+ – VIN–) times gain exceeds the voltage swing specification, the INAx181 drive
the output as close as possible to the positive supply or ground, and does not provide accurate measurement of
the differential input voltage. If this input overload occurs during normal circuit operation, then reduce the value of
the shunt resistor or use a lower-gain version with the chosen sense resistor to avoid this mode of operation. If a
differential overload occurs in a fault event, then the output of the INAx181 returns to the expected value
approximately 20 µs after the fault condition is removed.
When the INAx181 output is driven to either the supply rail or ground, increasing the differential input voltage
does not damage the device as long as the absolute maximum ratings are not violated. Following these
guidelines, the INAx181 output maintains polarity, and does not suffer from phase reversal.
版权 © 2017–2019, Texas Instruments Incorporated
21
INA181, INA2181, INA4181
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
www.ti.com.cn
Device Functional Modes (接下页)
8.4.5 Shutdown Mode
Although the INAx181 do not have a shutdown pin, the low power consumption of these devices allows the
output of a logic gate or transistor switch to power the INAx181. This gate or switch turns on and off the INAx181
power-supply quiescent current.
However, in current shunt monitoring applications, there is also a concern for how much current is drained from
the shunt circuit in shutdown conditions. Evaluating this current drain involves considering the simplified
schematic of the INAx181 in shutdown mode, as shown in 图 46.
VS
2.7 V to 5.5 V
RPULL-UP
10 kꢀ
Bus Voltage
œ0.2 V to +26 V
Shutdown
RSENSE
Load
CBYPASS
0.1 µF
VS
Single-Channel
TI Device
INœ
OUT
REF
œ
Output
+
IN+
GND
图 46. Basic Circuit to Shut Down the INA181 With a Grounded Reference
There is typically more than 500 kΩ of impedance (from the combination of 500-kΩ feedback and
input gain set resistors) from each input of the INAx181 to the OUT pin and to the REF pin. The amount of
current flowing through these pins depends on the voltage at the connection. For example, if the REF pin is
grounded, the calculation of the effect of the 500 kΩ impedance from the shunt to ground is straightforward.
However, if the reference is powered while the INAx181 is in shutdown mode, instead of assuming 500 kΩ to
ground, assume 500 kΩ to the reference voltage.
Regarding the 500-kΩ path to the output pin, the output stage of a disabled INAx181 does constitute a good path
to ground. Consequently, this current is directly proportional to a shunt common-mode voltage present across a
500-kΩ resistor.
As a final note, as long as the shunt common-mode voltage is greater than VS when the device is powered up,
there is an additional and well-matched 55-µA typical current that flows in each of the inputs. If less than VS, the
common-mode input currents are negligible, and the only current effects are the result of the 500-kΩ resistors.
22
版权 © 2017–2019, Texas Instruments Incorporated
INA181, INA2181, INA4181
www.ti.com.cn
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
9 Application and Implementation
注
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
The INAx181 amplify the voltage developed across a current-sensing resistor as current flows through the
resistor to the load or ground. The ability to drive the reference pin to adjust the functionality of the output signal
offers multiple configurations, as discussed in previous sections.
9.1.1 Basic Connections
图 47 shows the basic connections of the INA181. Connect the input pins (IN+ and IN–) as closely as possible to
the shunt resistor to minimize any resistance in series with the shunt resistor.
Bus Voltage
œ0.2 V to +26 V
Power Supply, VS
2.7 V to 5.5 V
CBYPASS
0.1 µF
RSENSE
Load
VS
Single-Channel
TI Device
INœ
Microcontroller
OUT
œ
ADC
+
IN+
REF
GND
NOTE: To help eliminate ground offset errors between the device and the analog-to-digital converter (ADC), connect
the REF pin to the ADC reference input and then to ground. For best performance, use an RC filter between the
output of the INAx181 and the ADC. See Closed-Loop Analysis of Load-Induced Amplifier Stability Issues Using
ZOUT for more details.
图 47. Basic Connections for the INA181
A power-supply bypass capacitor of at least 0.1 µF is required for proper operation. Applications with noisy or
high-impedance power supplies may require additional decoupling capacitors to reject power-supply noise.
Connect bypass capacitors close to the device pins.
版权 © 2017–2019, Texas Instruments Incorporated
23
INA181, INA2181, INA4181
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
www.ti.com.cn
Application Information (接下页)
9.1.2 RSENSE and Device Gain Selection
The accuracy of the INAx181 is maximized by choosing the current-sense resistor to be as large as possible. A
large sense resistor maximizes the differential input signal for a given amount of current flow and reduces the
error contribution of the offset voltage. However, there are practical limits as to how large the current-sense
resistor can be in a given application. The INAx181 have typical input bias currents of 75 µA for each input when
operated at a 12-V common-mode voltage input. When large current-sense resistors are used, these bias
currents cause increased offset error and reduced common-mode rejection. Therefore, using current-sense
resistors larger than a few ohms is generally not recommended for applications that require current-monitoring
accuracy. A second common restriction on the value of the current-sense resistor is the maximum allowable
power dissipation that is budgeted for the resistor. 公式 2 gives the maximum value for the current sense resistor
for a given power dissipation budget:
PDMAX
RSENSE
<
2
IMAX
where:
•
•
PDMAX is the maximum allowable power dissipation in RSENSE
.
IMAX is the maximum current that will flow through RSENSE
.
(2)
An additional limitation on the size of the current-sense resistor and device gain is due to the power-supply
voltage, VS, and device swing to rail limitations. In order to make sure that the current-sense signal is properly
passed to the output, both positive and negative output swing limitations must be examined. 公式 3 provides the
maximum values of RSENSE and GAIN to keep the device from hitting the positive swing limitation.
IMAX ìRSENSE ìGAIN < VSP - VREF
where:
•
•
•
•
IMAX is the maximum current that will flow through RSENSE
.
GAIN is the gain of the current sense-amplifier.
VSP is the positive output swing as specified in the data sheet.
VREF is the externally applied voltage on the REF pin.
(3)
To avoid positive output swing limitations when selecting the value of RSENSE, there is always a trade-off between
the value of the sense resistor and the gain of the device under consideration. If the sense resistor selected for
the maximum power dissipation is too large, then it is possible to select a lower-gain device in order to avoid
positive swing limitations.
The negative swing limitation places a limit on how small of a sense resistor can be used in a given application.
公式 4 provides the limit on the minimum size of the sense resistor.
IMIN ìRSENSE ìGAIN > VSN - VREF
where:
•
•
•
•
IMIN is the minimum current that will flow through RSENSE
.
GAIN is the gain of the current sense amplifier.
VSN is the negative output swing of the device (see Rail-to-Rail Output Swing).
VREF is the externally applied voltage on the REF pin.
(4)
In addition to adjusting the offset and gain, the voltage applied to the REF pin can be slightly increased to avoid
negative swing limitations.
24
版权 © 2017–2019, Texas Instruments Incorporated
INA181, INA2181, INA4181
www.ti.com.cn
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
Application Information (接下页)
9.1.3 Signal Filtering
Provided that the INAx181 output is connected to a high impedance input, the best location to filter is at the
device output using a simple RC network from OUT to GND. Filtering at the output attenuates high-frequency
disturbances in the common-mode voltage, differential input signal, and INAx181 power-supply voltage. If filtering
at the output is not possible, or filtering of only the differential input signal is required, it is possible to apply a
filter at the input pins of the device. 图 48 provides an example of how a filter can be used on the input pins of
the device.
Bus Voltage
œ0.2 V to +26 V
RSENSE
Load
VS
2.7 V to 5.5 V
1
VS
Single-Channel
f-3dB
=
TI Device
2p(RF + RF )CF
RF < 10 ꢀ
RINT
INœ
fœ3dB
VOUT
CF
œ
OUT
REF
Bias
+
RF < 10 ꢀ
RINT
VREF
IN+
图 48. Filter at Input Pins
The addition of external series resistance creates an additional error in the measurement; therefore, the value of
these series resistors must be kept to 10 Ω (or less, if possible) to reduce impact to accuracy. The internal bias
network shown in 图 48 present at the input pins creates a mismatch in input bias currents when a differential
voltage is applied between the input pins. If additional external series filter resistors are added to the circuit, the
mismatch in bias currents results in a mismatch of voltage drops across the filter resistors. This mismatch
creates a differential error voltage that subtracts from the voltage developed across the shunt resistor. This error
results in a voltage at the device input pins that is different than the voltage developed across the shunt resistor.
Without the additional series resistance, the mismatch in input bias currents has little effect on device operation.
The amount of error these external filter resistors add to the measurement can be calculated using 公式 6, where
the gain error factor is calculated using 公式 5.
The amount of variance in the differential voltage present at the device input relative to the voltage developed at
the shunt resistor is based both on the external series resistance (RF) value as well as internal input resistor RINT
,
as shown in 图 48. The reduction of the shunt voltage reaching the device input pins appears as a gain error
when comparing the output voltage relative to the voltage across the shunt resistor. A factor can be calculated to
determine the amount of gain error that is introduced by the addition of external series resistance. Calculate the
expected deviation from the shunt voltage to what is measured at the device input pins is given using 公式 5:
1250ìRINT
(1250ìRF ) + (1250ìRINT ) + (RF ìRINT
Gain Error Factor =
)
where:
•
•
RINT is the internal input resistor.
RF is the external series resistance.
(5)
版权 © 2017–2019, Texas Instruments Incorporated
25
INA181, INA2181, INA4181
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
www.ti.com.cn
Application Information (接下页)
With the adjustment factor from 公式 5, including the device internal input resistance, this factor varies with each
gain version, as shown in 表 1. Each individual device gain error factor is shown in 表 2.
表 1. Input Resistance
PRODUCT
INAx181A1
INAx181A2
INAx181A3
INAx181A4
GAIN
20
RINT (kΩ)
25
10
5
50
100
200
2.5
表 2. Device Gain Error Factor
PRODUCT
SIMPLIFIED GAIN ERROR FACTOR
25000
INAx181A1
(21ìRF ) + 25000
10000
INAx181A2
INAx181A3
INAx181A4
(9ìRF ) +10000
1000
RF +1000
2500
(3ìRF ) + 2500
The gain error that can be expected from the addition of the external series resistors can then be calculated
based on 公式 6:
Gain Error (%) = 100 - (100 ´ Gain Error Factor)
(6)
For example, using an INA181A2 and the corresponding gain error equation from 表 2, a series resistance of
10 Ω results in a gain error factor of 0.991. The corresponding gain error is then calculated using 公式 6,
resulting in an additional gain error of approximately 0.89% solely because of the external 10-Ω series resistors.
26
版权 © 2017–2019, Texas Instruments Incorporated
INA181, INA2181, INA4181
www.ti.com.cn
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
9.1.4 Summing Multiple Currents
The outputs of the INA2181 are easily summed by connecting the output of one channel to the reference input of
a second channel. The circuit configuration shown in 图 49 is an easy way to achieve current summing. To
correctly sum multiple output currents the values for the current sense resistor RSENSE must be the same for all
channels.
Power
Supply
Dual-Channel
TI Device
REF1
OUT1
IN+1
+
RSENSE
œ
INœ1
LOAD1
REF2
OUT2
IN+2
+
ADC
RSENSE
œ
VOUT2 = (ILOAD1 + ILOAD2) × RSENSE × GAIN
INœ2
LOAD2
GND
图 49. Summing Multiple Currents
Connect the output of one channel of the INA2181 to the reference input of the other channel. Use the reference
input of the first circuit to set the reference of the final summed output operating point. The currents sensed at
each circuit in the chain are summed at the output of the last device in the chain.
版权 © 2017–2019, Texas Instruments Incorporated
27
INA181, INA2181, INA4181
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
www.ti.com.cn
An example output response of a summing configuration is shown in 图 50. The reference pin of the first circuit is
connected to ground, and sine waves at different frequencies are applied to the two circuits to produce a
summed output as shown. The sine wave voltage input for the first circuit is offset so that the whole wave is
above GND.
Output
Inputs
Time (4 ms/div)
VREF = 0 V
图 50. Current Summing Application Output Response (A2 Devices)
9.1.5 Detecting Leakage Currents
Occasionally, the need arises to confirm that the current going into a load is identical to the current coming out of
a load; usually, as part of diagnostic testing or fault detection. This situation requires precision current
differencing, which is the same as summing, except that the two amplifiers have the inputs connected opposite of
each other. To correctly detect leakage currents, the values for the current sense resistor RSENSE must be the
same for all channels. Also an external reference voltage must be provided to the REF1 input to allow
bidirectional leakage current detection.
If the current into a load is equal to the current out of the load, then the voltage at OUT2 is the same as the
applied voltage to REF1. To enable accurate differences between the two currents, a reference voltage must be
applied. The reference voltage prevents the output of the device from being driven to ground, and also enables
detection if the current into the load is either greater than or less than the current coming out of the load.
For current differencing, the dual-channel INA2181 must have the inputs connected opposite to each other, as
shown in 图 51. The reference input of the first channel sets the output quiescent level for all the devices in the
string. Connect the output of the first channel to the reference input of the second channel. The reference input
of the first channel sets the reference at the output. This circuit example is identical to the current summing
example, except that the two shunt inputs are reversed in polarity. Under normal operating conditions, the final
output is very close to the reference value and proportional to any current difference. This current differencing
circuit is useful in detecting when current in to and out of a load do not match.
28
版权 © 2017–2019, Texas Instruments Incorporated
INA181, INA2181, INA4181
www.ti.com.cn
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
Power
Supply
Dual-Channel
TI Device
REF1
OUT1
IN+1
VREF1
+
RSENSE
œ
INœ1
LOAD
REF2
OUT2
IN+2
+
ADC
RSENSE
œ
VOUT2 = VREF1 if there is no leakage current
INœ2
图 51. Detecting Leakage Currents
An example output response of a difference configuration is shown in 图 52. The reference pin of the first
channel is connected to a reference voltage of 2.048 V. The inputs to each circuit is a 100-Hz sine wave, 180°
out-of-phase with each other, resulting in a zero output as shown. The sine wave input to the first circuit is offset
so that the input wave is completely above GND.
Output
Inputs
Time (4 ms/div)
VREF = 2.048 V
图 52. Current Differencing Application Output Response (A2 Devices)
版权 © 2017–2019, Texas Instruments Incorporated
29
INA181, INA2181, INA4181
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
www.ti.com.cn
9.2 Typical Application
One application for the INAx181 is to monitor bidirectional currents. Bidirectional currents are present in systems
that have to monitor currents in both directions; common examples are monitoring the charging and discharging
of batteries and bidirectional current monitoring in motor control. The device configuration for bidirectional current
monitoring is shown in 图 53. Applying stable REF pin voltage closer to the middle of device supply voltage
allows both positive- and negative-current monitoring, as shown in this configuration. Configure the INAx181 to
monitor unidirectional currents by grounding the REF pin.
Bus Voltage
œ0.2 V to +26 V
Power Supply, VS
2.7 V to 5.5 V
CBYPASS
0.1 µF
RSENSE
Load
VS
Single-Channel
TI Device
Reference
Voltage
INœ
œ
OUT
REF
Output
+
IN+
+
œ
GND
图 53. Measuring Bidirectional Current
9.2.1 Design Requirements
The design requirements for the circuit shown in 图 53, are listed in 表 3
表 3. Design Parameters
DESIGN PARAMETER
Power-supply voltage, VS
Bus supply rail, VCM
EXAMPLE VALUE
5 V
12 V
RSENSE power loss
< 450 mW
±20 A
Maximum sense current, IMAX
Current sensing error
Small-signal bandwidth
Less than 3.5% at maximum current, TJ = 25°C
> 100 kHz
9.2.2 Detailed Design Procedure
The maximum value of the current sense resistor is calculated based on the maximum power loss requirement.
By applying 公式 2, the maximum value of the current-sense resistor is calculated to be 1.125 mΩ. This is the
maximum value for sense resistor RSENSE; therefore, select RSENSE to be 1 mΩ because it is the closest standard
resistor value that meets the power-loss requirement.
The next step is to select the appropriate gain and reduce RSENSE, if needed, to keep the output signal swing
within the VS range. The design requirements call for bidirectional current monitoring; therefore, a voltage
between 0 and VS must be applied to the REF pin. The bidirectional currents monitored are symmetric around 0
(that is, ±20 A); therefore, the ideal voltage to apply to VREF is VS / 2 or 2.5 V. If the positive current is greater
than the negative current, using a lower voltage on VREF has the benefit of maximizing the output swing for the
given range of expected currents. Using 公式 3, and given that IMAX = 20 A , RSENSE = 1 mΩ, and VREF = 2.5 V,
30
版权 © 2017–2019, Texas Instruments Incorporated
INA181, INA2181, INA4181
www.ti.com.cn
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
the maximum current-sense gain calculated to avoid the positive swing-to-rail limitations on the output is 122.5.
Likewise, using 公式 4 for the negative-swing limitation results in a maximum gain of 124.75. Selecting the gain-
of-100 device maximizes the output range while staying within the output swing range. If the maximum calculated
gains are slightly less than 100, the value of the current-sense resistor can be reduced to keep the output from
hitting the output-swing limitations.
To calculate the accuracy at peak current, the two factors that must be determined are the gain error and the
offset error. The gain error of the INAx181 is specified to be a maximum of 1%. The error due to the offset is
constant, and is specified to be 500 µV (maximum) for the conditions where VCM = 12 V and VS = 5 V. Using 公
式 7, the percentage error contribution of the offset voltage is calculated to be 2.5%, with total offset error = 500
µV, RSENSE = 1 mΩ, and ISENSE = 20 A.
Total Offset Error (V)
Total Offset Error (%) =
ì100%
ISENSE ìRSENSE
(7)
One method of calculating the total error is to add the gain error to the percentage contribution of the offset error.
However, in this case, the gain error and the offset error do not have an influence or correlation to each other. A
more statistically accurate method of calculating the total error is to use the RSS sum of the errors, as shown in
公式 8:
Total Error (%) = Total Gain Error (%)2 + Total Offset Error (%)2
(8)
After applying 公式 8, the total current sense error at maximum current is calculated to be 2.7%, and that is less
than the design example requirement of 3.5%.
The INA181A3 (gain = 100) also has a bandwidth of 150 kHz that meets the small-signal bandwidth requirement
of 100 kHz. If higher bandwidth is required, lower-gain devices can be used at the expense of either reduced
output voltage range or an increased value of RSENSE
.
9.2.3 Application Curve
An example output response of a bidirectional configuration is shown in 图 54. With the REF pin connected to a
reference voltage (2.5 V in this case), the output voltage is biased upwards by this reference level. The output
rises above the reference voltage for positive differential input signals, and falls below the reference voltage for
negative differential input signals.
VOUT
VREF
0V
Time (500 µs/div)
C002
图 54. Bidirectional Application Output Response
版权 © 2017–2019, Texas Instruments Incorporated
31
INA181, INA2181, INA4181
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
www.ti.com.cn
10 Power Supply Recommendations
The input circuitry of the INAx181 accurately measures beyond the power-supply voltage, VS. For example, VS
can be 5 V, whereas the bus supply voltage at IN+ and IN– can be as high as 26 V. However, the output voltage
range of the OUT pin is limited by the voltages on the VS pin. The INAx181 also withstand the full differential
input signal range up to 26 V at the IN+ and IN– input pins, regardless of whether or not the device has power
applied at the VS pin.
10.1 Common-Mode Transients Greater Than 26 V
With a small amount of additional circuitry, the INAx181 can be used in circuits subject to transients higher than
26 V, such as automotive applications. Use only Zener diodes or Zener-type transient absorbers (sometimes
referred to as transzorbs)—any other type of transient absorber has an unacceptable time delay. Start by adding
a pair of resistors as a working impedance for the Zener diode; see 图 55. Keep these resistors as small as
possible; most often, around 10 Ω. Larger values can be used with an effect on gain that is discussed in the
Signal Filtering section. This circuit limits only short-term transients; therefore, many applications are satisfied
with a 10-Ω resistor along with conventional Zener diodes of the lowest acceptable power rating. This
combination uses the least amount of board space. These diodes can be found in packages as small as SOT-
523 or SOD-523.
VS
2.7 V to 5.5 V
CBYPASS
0.1 µF
Bus Supply
œ0.2 V to +26 V
RSENSE
Load
VS
Single-Channel
TI Device
INœ
œ
OUT
RPROTECT
< 10 ꢀ
Output
+
REF
IN+
GND
图 55. Transient Protection Using Dual Zener Diodes
In the event that low-power Zener diodes do not have sufficient transient absorption capability, a higher-power
transzorb must be used. The most package-efficient solution involves using a single transzorb and back-to-back
diodes between the device inputs, as shown in 图 56. The most space-efficient solutions are dual, series-
connected diodes in a single SOT-523 or SOD-523 package. In either of the examples shown in 图 55 and 图 56,
the total board area required by the INAx181 with all protective components is less than that of an SO-8
package, and only slightly greater than that of an MSOP-8 package.
VS
CBYPASS
0.1 µF
2.7 V to 5.5 V
Bus Supply
œ0.2 V to +26 V
RSENSE
Load
VS
Single-Channel
TI Device
< 10 ꢀ
INœ
œ
OUT
Transorb
Output
+
< 10 ꢀ
REF
IN+
GND
图 56. Transient Protection Using a Single Transzorb and Input Clamps
32
版权 © 2017–2019, Texas Instruments Incorporated
INA181, INA2181, INA4181
www.ti.com.cn
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
Common-Mode Transients Greater Than 26 V (接下页)
For more information, see Current Shunt Monitor With Transient Robustness Reference Design.
11 Layout
11.1 Layout Guidelines
•
Connect the input pins to the sensing resistor using a Kelvin or 4-wire connection. This connection technique
makes sure that only the current-sensing resistor impedance is detected between the input pins. Poor routing
of the current-sensing resistor commonly results in additional resistance present between the input pins.
Given the very low ohmic value of the current resistor, any additional high-current carrying impedance can
cause significant measurement errors.
•
•
Place the power-supply bypass capacitor as close as possible to the device power supply and ground pins.
The recommended value of this bypass capacitor is 0.1 µF. Additional decoupling capacitance can be added
to compensate for noisy or high-impedance power supplies.
When routing the connections from the current sense resistor to the device, keep the trace lengths as close
as possible in order to minimize any impedance mismatch..
11.2 Layout Example
Direction of Positive
Current Flow
RSHUNT
Bus Voltage:
œ0.2 V to +26 V
4
5
6
3
IN+
GND
OUT
INœ
Connect REF to low
impedance voltage reference
or to GND pin if not used.
2
1
REF
VS
Current
Sense
VIA to Ground
Plane
CBYPASS
Power-Supply, VS
2.7 V to 5.5 V
图 57. Single-Channel Recommended Layout
版权 © 2017–2019, Texas Instruments Incorporated
33
INA181, INA2181, INA4181
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
www.ti.com.cn
Layout Example (接下页)
Bus Voltage:
œ0.2 V to +26 V
VIA to connect REF pins to low
impedance voltage reference or
to GND pin if not used.
VIA to
Ground
Plane
6
5
4
3
2
1
REF1
GND
IN+1
INœ1
REF2
IN+2
INœ2
OUT2
VS
7
RSHUNT2
8
RSHUNT1
9
10
OUT1
Current Sense
Output 2
CBYPASS
Current Sense
Output 1
Power Supply, VS:
2.7 V to 5.5 V
Load 2
Load 1
图 58. Dual-Channel Recommended Layout
34
版权 © 2017–2019, Texas Instruments Incorporated
INA181, INA2181, INA4181
www.ti.com.cn
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
Layout Example (接下页)
Load 2
Load 3
Current Sense
Output 2
Current Sense
Output 3
Connect to GND or
External Reference
11
12
13
14
15
16
17
10
9
8
7
6
5
4
3
2
1
NC
NC
REF3
OUT3
INœ3
REF2
OUT2
INœ2
IN+2
RSHUNT3
RSHUNT2
IN+3
VIA to
Ground
Plane
CBYPASS
GND
IN+4
VS
Bus Voltage 2:
œ0.2 V to +26 V
IN+1
INœ1
OUT1
REF1
Bus Voltage 3:
œ0.2 V to +26 V
INœ4 18
19
OUT4
VIA to
Ground
Plane
Power Supply, VS:
20
REF4
2.7 V to 5.5 V
Current Sense
Output 4
Current Sense
Output 1
Bus Voltage 4:
Bus Voltage 1:
œ0.2 V to +26 V
œ0.2 V to +26 V
RSHUNT4
RSHUNT1
Load 4
Load 1
图 59. Quad-Channel Recommended Layout
版权 © 2017–2019, Texas Instruments Incorporated
35
INA181, INA2181, INA4181
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
www.ti.com.cn
12 器件和文档支持
12.1 器件支持
12.1.1 开发支持
《具有瞬态稳定性的电流分流监控器参考设计》
12.2 文档支持
12.2.1 相关文档
请参阅如下相关文档:
•
•
•
德州仪器 (TI),《INA180-181EVM 用户指南》
德州仪器 (TI),《INA2180-2181EVM 用户指南》
德州仪器 (TI),《INA4180-4181EVM 用户指南》
12.3 相关链接
表 4 列出了快速访问链接。类别包括技术文档、支持和社区资源、工具与软件,以及立即订购快速访问。
表 4. 相关链接
器件
产品文件夹
请单击此处
请单击此处
请单击此处
立即订购
请单击此处
请单击此处
请单击此处
技术文档
请单击此处
请单击此处
请单击此处
工具与软件
请单击此处
请单击此处
请单击此处
支持和社区
请单击此处
请单击此处
请单击此处
INA181
INA2181
INA4181
12.4 接收文档更新通知
要接收文档更新通知,请导航至 TI.com.cn 上的器件产品文件夹。单击右上角的通知我 进行注册,即可每周接收产
品信息更改摘要。有关更改的详细信息,请查看任何已修订文档中包含的修订历史记录。
12.5 社区资源
下列链接提供到 TI 社区资源的连接。链接的内容由各个分销商“按照原样”提供。这些内容并不构成 TI 技术规范,
并且不一定反映 TI 的观点;请参阅 TI 的 《使用条款》。
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
12.6 商标
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
12.7 静电放电警告
ESD 可能会损坏该集成电路。德州仪器 (TI) 建议通过适当的预防措施处理所有集成电路。如果不遵守正确的处理措施和安装程序 , 可
能会损坏集成电路。
ESD 的损坏小至导致微小的性能降级 , 大至整个器件故障。 精密的集成电路可能更容易受到损坏 , 这是因为非常细微的参数更改都可
能会导致器件与其发布的规格不相符。
12.8 术语表
SLYZ022 — TI 术语表。
这份术语表列出并解释术语、缩写和定义。
36
版权 © 2017–2019, Texas Instruments Incorporated
INA181, INA2181, INA4181
www.ti.com.cn
ZHCSG77F –APRIL 2017–REVISED MARCH 2019
13 机械、封装和可订购信息
以下页面包含机械、封装和可订购信息。这些信息是指定器件的最新可用数据。数据如有变更,恕不另行通知,且
不会对此文档进行修订。如需获取此产品说明书的浏览器版本,请查阅左侧的导航栏。
版权 © 2017–2019, Texas Instruments Incorporated
37
PACKAGE OPTION ADDENDUM
www.ti.com
14-Jun-2023
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
INA181A1IDBVR
INA181A1IDBVT
INA181A2IDBVR
INA181A2IDBVT
INA181A3IDBVR
INA181A3IDBVT
INA181A4IDBVR
INA181A4IDBVT
INA2181A1IDGSR
INA2181A1IDGST
INA2181A1IDSQR
INA2181A1IDSQT
INA2181A2IDGSR
INA2181A2IDGST
INA2181A2IDSQR
INA2181A2IDSQT
INA2181A3IDGSR
INA2181A3IDGST
INA2181A3IDSQR
INA2181A3IDSQT
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
VSSOP
VSSOP
WSON
WSON
VSSOP
VSSOP
WSON
WSON
VSSOP
VSSOP
WSON
WSON
DBV
DBV
DBV
DBV
DBV
DBV
DBV
DBV
DGS
DGS
DSQ
DSQ
DGS
DGS
DSQ
DSQ
DGS
DGS
DSQ
DSQ
6
6
3000 RoHS & Green
250 RoHS & Green
3000 RoHS & Green
250 RoHS & Green
3000 RoHS & Green
250 RoHS & Green
3000 RoHS & Green
250 RoHS & Green
2500 RoHS & Green
250 RoHS & Green
3000 RoHS & Green
250 RoHS & Green
2500 RoHS & Green
250 RoHS & Green
3000 RoHS & Green
250 RoHS & Green
2500 RoHS & Green
250 RoHS & Green
3000 RoHS & Green
250 RoHS & Green
SN
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
18JD
18JD
1AED
1AED
1AFD
1AFD
1AGD
1AGD
1CW6
1CW6
25IY
Samples
Samples
Samples
Samples
Samples
Samples
Samples
Samples
Samples
Samples
Samples
Samples
Samples
Samples
Samples
Samples
Samples
Samples
Samples
Samples
SN
SN
6
6
SN
6
SN
6
SN
6
SN
6
SN
10
10
10
10
10
10
10
10
10
10
10
10
NIPDAUAG | SN
NIPDAUAG | SN
NIPDAU
NIPDAU
25IY
NIPDAUAG | SN
NIPDAUAG | SN
NIPDAU
1DR6
1DR6
25JY
25JY
1DS6
1DS6
25KY
25KY
NIPDAU
NIPDAUAG | SN
NIPDAUAG | SN
NIPDAU
NIPDAU
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
14-Jun-2023
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
INA2181A4IDGSR
INA2181A4IDGST
INA2181A4IDSQR
INA2181A4IDSQT
INA4181A1IPWR
INA4181A2IPWR
INA4181A3IPWR
INA4181A4IPWR
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
VSSOP
VSSOP
WSON
WSON
TSSOP
TSSOP
TSSOP
TSSOP
DGS
DGS
DSQ
DSQ
PW
10
10
10
10
20
20
20
20
2500 RoHS & Green
250 RoHS & Green
3000 RoHS & Green
250 RoHS & Green
NIPDAUAG | SN
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
1DT6
1DT6
25LY
25LY
Samples
Samples
Samples
Samples
Samples
Samples
Samples
Samples
NIPDAUAG | SN
NIPDAU
NIPDAU
2000 RoHS & Green
2000 RoHS & Green
2000 RoHS & Green
2000 RoHS & Green
NIPDAU
4181A1
4181A2
4181A3
4181A4
PW
NIPDAU
PW
NIPDAU
PW
NIPDAU
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
14-Jun-2023
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF INA181, INA2181, INA4181 :
Automotive : INA181-Q1, INA2181-Q1, INA4181-Q1
•
NOTE: Qualified Version Definitions:
Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
•
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
16-Jun-2023
TAPE AND REEL INFORMATION
REEL DIMENSIONS
TAPE DIMENSIONS
K0
P1
W
B0
Reel
Diameter
Cavity
A0
A0 Dimension designed to accommodate the component width
B0 Dimension designed to accommodate the component length
K0 Dimension designed to accommodate the component thickness
Overall width of the carrier tape
W
P1 Pitch between successive cavity centers
Reel Width (W1)
QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE
Sprocket Holes
Q1 Q2
Q3 Q4
Q1 Q2
Q3 Q4
User Direction of Feed
Pocket Quadrants
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
INA181A1IDBVR
INA181A1IDBVT
INA181A2IDBVR
INA181A2IDBVT
INA181A3IDBVR
INA181A3IDBVT
INA181A4IDBVR
INA181A4IDBVT
INA2181A1IDGSR
INA2181A1IDGSR
INA2181A1IDGST
INA2181A1IDGST
INA2181A1IDSQR
INA2181A1IDSQT
INA2181A2IDGSR
INA2181A2IDGST
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
VSSOP
VSSOP
VSSOP
VSSOP
WSON
DBV
DBV
DBV
DBV
DBV
DBV
DBV
DBV
DGS
DGS
DGS
DGS
DSQ
DSQ
DGS
DGS
6
6
3000
250
178.0
178.0
178.0
178.0
178.0
178.0
178.0
178.0
330.0
330.0
330.0
330.0
180.0
180.0
330.0
330.0
9.0
9.0
3.23
3.23
3.23
3.23
3.23
3.23
3.23
3.23
5.3
3.17
3.17
3.17
3.17
3.17
3.17
3.17
3.17
3.4
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.4
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
8.0
8.0
8.0
8.0
4.0
4.0
8.0
8.0
8.0
8.0
Q3
Q3
Q3
Q3
Q3
Q3
Q3
Q3
Q1
Q1
Q1
Q1
Q2
Q2
Q1
Q1
6
3000
250
9.0
8.0
6
9.0
8.0
6
3000
250
9.0
8.0
6
9.0
8.0
6
3000
250
9.0
8.0
6
9.0
8.0
10
10
10
10
10
10
10
10
2500
2500
250
12.4
12.4
12.4
12.4
8.4
12.0
12.0
12.0
12.0
8.0
5.3
3.4
1.4
5.3
3.4
1.4
250
5.3
3.4
1.4
3000
250
2.3
2.3
1.15
1.15
1.4
WSON
8.4
2.3
2.3
8.0
VSSOP
VSSOP
2500
250
12.4
12.4
5.3
3.4
12.0
12.0
5.3
3.4
1.4
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
16-Jun-2023
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
INA2181A2IDSQR
INA2181A2IDSQT
INA2181A3IDGSR
INA2181A3IDGST
INA2181A3IDSQR
INA2181A3IDSQT
INA2181A4IDGSR
INA2181A4IDGSR
INA2181A4IDGST
INA2181A4IDGST
INA2181A4IDSQR
INA2181A4IDSQT
INA4181A1IPWR
INA4181A2IPWR
INA4181A3IPWR
INA4181A4IPWR
WSON
WSON
VSSOP
VSSOP
WSON
WSON
VSSOP
VSSOP
VSSOP
VSSOP
WSON
WSON
TSSOP
TSSOP
TSSOP
TSSOP
DSQ
DSQ
DGS
DGS
DSQ
DSQ
DGS
DGS
DGS
DGS
DSQ
DSQ
PW
10
10
10
10
10
10
10
10
10
10
10
10
20
20
20
20
3000
250
180.0
180.0
330.0
330.0
180.0
180.0
330.0
330.0
330.0
330.0
180.0
180.0
330.0
330.0
330.0
330.0
8.4
8.4
2.3
2.3
2.3
2.3
3.4
3.4
2.3
2.3
3.4
3.4
3.4
3.4
2.3
2.3
7.0
7.0
7.0
7.0
1.15
1.15
1.4
4.0
4.0
8.0
8.0
4.0
4.0
8.0
8.0
8.0
8.0
4.0
4.0
8.0
8.0
8.0
8.0
8.0
8.0
Q2
Q2
Q1
Q1
Q2
Q2
Q1
Q1
Q1
Q1
Q2
Q2
Q1
Q1
Q1
Q1
2500
250
12.4
12.4
8.4
5.3
12.0
12.0
8.0
5.3
1.4
3000
250
2.3
1.15
1.15
1.4
8.4
2.3
8.0
2500
2500
250
12.4
12.4
12.4
12.4
8.4
5.3
12.0
12.0
12.0
12.0
8.0
5.3
1.4
5.3
1.4
250
5.3
1.4
3000
250
2.3
1.15
1.15
1.4
8.4
2.3
8.0
2000
2000
2000
2000
16.4
16.4
16.4
16.4
6.95
6.95
6.95
6.95
16.0
16.0
16.0
16.0
PW
1.4
PW
1.4
PW
1.4
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
16-Jun-2023
TAPE AND REEL BOX DIMENSIONS
Width (mm)
H
W
L
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
INA181A1IDBVR
INA181A1IDBVT
INA181A2IDBVR
INA181A2IDBVT
INA181A3IDBVR
INA181A3IDBVT
INA181A4IDBVR
INA181A4IDBVT
INA2181A1IDGSR
INA2181A1IDGSR
INA2181A1IDGST
INA2181A1IDGST
INA2181A1IDSQR
INA2181A1IDSQT
INA2181A2IDGSR
INA2181A2IDGST
INA2181A2IDSQR
INA2181A2IDSQT
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
VSSOP
VSSOP
VSSOP
VSSOP
WSON
WSON
VSSOP
VSSOP
WSON
WSON
DBV
DBV
DBV
DBV
DBV
DBV
DBV
DBV
DGS
DGS
DGS
DGS
DSQ
DSQ
DGS
DGS
DSQ
DSQ
6
6
3000
250
180.0
180.0
180.0
180.0
180.0
180.0
180.0
180.0
366.0
366.0
366.0
366.0
210.0
210.0
366.0
366.0
210.0
210.0
180.0
180.0
180.0
180.0
180.0
180.0
180.0
180.0
364.0
364.0
364.0
364.0
185.0
185.0
364.0
364.0
185.0
185.0
18.0
18.0
18.0
18.0
18.0
18.0
18.0
18.0
50.0
50.0
50.0
50.0
35.0
35.0
50.0
50.0
35.0
35.0
6
3000
250
6
6
3000
250
6
6
3000
250
6
10
10
10
10
10
10
10
10
10
10
2500
2500
250
250
3000
250
2500
250
3000
250
Pack Materials-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
16-Jun-2023
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
INA2181A3IDGSR
INA2181A3IDGST
INA2181A3IDSQR
INA2181A3IDSQT
INA2181A4IDGSR
INA2181A4IDGSR
INA2181A4IDGST
INA2181A4IDGST
INA2181A4IDSQR
INA2181A4IDSQT
INA4181A1IPWR
INA4181A2IPWR
INA4181A3IPWR
INA4181A4IPWR
VSSOP
VSSOP
WSON
WSON
VSSOP
VSSOP
VSSOP
VSSOP
WSON
WSON
TSSOP
TSSOP
TSSOP
TSSOP
DGS
DGS
DSQ
DSQ
DGS
DGS
DGS
DGS
DSQ
DSQ
PW
10
10
10
10
10
10
10
10
10
10
20
20
20
20
2500
250
366.0
366.0
210.0
210.0
366.0
366.0
366.0
366.0
210.0
210.0
356.0
356.0
356.0
356.0
364.0
364.0
185.0
185.0
364.0
364.0
364.0
364.0
185.0
185.0
356.0
356.0
356.0
356.0
50.0
50.0
35.0
35.0
50.0
50.0
50.0
50.0
35.0
35.0
35.0
35.0
35.0
35.0
3000
250
2500
2500
250
250
3000
250
2000
2000
2000
2000
PW
PW
PW
Pack Materials-Page 4
PACKAGE OUTLINE
DSQ0010A
WSON - 0.8 mm max height
S
C
A
L
E
5
.
0
0
0
PLASTIC SMALL OUTLINE - NO LEAD
2.1
1.9
A
B
PIN 1 INDEX AREA
2.1
1.9
0.8
0.7
C
SEATING PLANE
0.08 C
0.05
0.00
0.9 0.1
SYMM
EXPOSED
THERMAL PAD
(0.2) TYP
5
6
SYMM
1.5 0.1
11
2X 1.6
8X 0.4
1
PIN 1 ID
10
0.25
0.15
10X
0.4
0.2
10X
0.1
C A B
0.05
4218906/A 04/2019
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. The package thermal pad must be soldered to the printed circuit board for thermal and mechanical performance.
www.ti.com
EXAMPLE BOARD LAYOUT
DSQ0010A
WSON - 0.8 mm max height
PLASTIC SMALL OUTLINE - NO LEAD
(0.9)
SEE SOLDER MASK
DETAIL
10X (0.5)
10X (0.2)
SYMM
10
1
(1.5)
8X (0.4)
11
SYMM
(0.5)
(R0.05) TYP
5
6
(
0.2) TYP
VIA
(1.9)
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE: 20X
0.07 MIN
ALL AROUND
0.07 MAX
ALL AROUND
METAL UNDER
SOLDER MASK
METAL EDGE
EXPOSED METAL
SOLDER MASK
OPENING
EXPOSED
METAL
SOLDER MASK
OPENING
NON SOLDER MASK
DEFINED
SOLDER MASK DEFINED
(PREFERRED)
SOLDER MASK DETAILS
4218906/A 04/2019
NOTES: (continued)
4. This package is designed to be soldered to a thermal pad on the board. For more information, see Texas Instruments literature
number SLUA271 (www.ti.com/lit/slua271).
5. Vias are optional depending on application, refer to device data sheet. If any vias are implemented, refer to their locations shown
on this view. It is recommended that vias under paste be filled, plugged or tented.
www.ti.com
EXAMPLE STENCIL DESIGN
DSQ0010A
WSON - 0.8 mm max height
PLASTIC SMALL OUTLINE - NO LEAD
10X (0.5)
10X (0.2)
(0.85)
10
1
8X (0.4)
11
SYMM
(1.38)
(R0.05) TYP
5
6
SYMM
(1.9)
SOLDER PASTE EXAMPLE
BASED ON 0.125 MM THICK STENCIL
SCALE: 20X
EXPOSED PAD 11
87% PRINTED SOLDER COVERAGE BY AREA UNDER PACKAGE
4218906/A 04/2019
NOTES: (continued)
6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
www.ti.com
PACKAGE OUTLINE
DGS0010A
VSSOP - 1.1 mm max height
S
C
A
L
E
3
.
2
0
0
SMALL OUTLINE PACKAGE
C
SEATING PLANE
0.1 C
5.05
4.75
TYP
PIN 1 ID
AREA
A
8X 0.5
10
1
3.1
2.9
NOTE 3
2X
2
5
6
0.27
0.17
10X
3.1
2.9
1.1 MAX
0.1
C A
B
B
NOTE 4
0.23
0.13
TYP
SEE DETAIL A
0.25
GAGE PLANE
0.15
0.05
0.7
0.4
0 - 8
DETAIL A
TYPICAL
4221984/A 05/2015
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed 0.15 mm per side.
4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.25 mm per side.
5. Reference JEDEC registration MO-187, variation BA.
www.ti.com
EXAMPLE BOARD LAYOUT
DGS0010A
VSSOP - 1.1 mm max height
SMALL OUTLINE PACKAGE
10X (1.45)
(R0.05)
TYP
SYMM
10X (0.3)
1
5
10
SYMM
6
8X (0.5)
(4.4)
LAND PATTERN EXAMPLE
SCALE:10X
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
METAL
0.05 MAX
ALL AROUND
0.05 MIN
ALL AROUND
SOLDER MASK
DEFINED
NON SOLDER MASK
DEFINED
SOLDER MASK DETAILS
NOT TO SCALE
4221984/A 05/2015
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
DGS0010A
VSSOP - 1.1 mm max height
SMALL OUTLINE PACKAGE
10X (1.45)
SYMM
(R0.05) TYP
10X (0.3)
8X (0.5)
1
5
10
SYMM
6
(4.4)
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
SCALE:10X
4221984/A 05/2015
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
www.ti.com
PACKAGE OUTLINE
DBV0006A
SOT-23 - 1.45 mm max height
S
C
A
L
E
4
.
0
0
0
SMALL OUTLINE TRANSISTOR
C
3.0
2.6
0.1 C
1.75
1.45
B
1.45 MAX
A
PIN 1
INDEX AREA
1
2
6
5
2X 0.95
1.9
3.05
2.75
4
3
0.50
6X
0.25
C A B
0.15
0.00
0.2
(1.1)
TYP
0.25
GAGE PLANE
0.22
0.08
TYP
8
TYP
0
0.6
0.3
TYP
SEATING PLANE
4214840/C 06/2021
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. Body dimensions do not include mold flash or protrusion. Mold flash and protrusion shall not exceed 0.25 per side.
4. Leads 1,2,3 may be wider than leads 4,5,6 for package orientation.
5. Refernce JEDEC MO-178.
www.ti.com
EXAMPLE BOARD LAYOUT
DBV0006A
SOT-23 - 1.45 mm max height
SMALL OUTLINE TRANSISTOR
PKG
6X (1.1)
1
6X (0.6)
6
SYMM
5
2
3
2X (0.95)
4
(R0.05) TYP
(2.6)
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:15X
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
METAL
EXPOSED METAL
EXPOSED METAL
0.07 MIN
ARROUND
0.07 MAX
ARROUND
NON SOLDER MASK
DEFINED
SOLDER MASK
DEFINED
(PREFERRED)
SOLDER MASK DETAILS
4214840/C 06/2021
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
DBV0006A
SOT-23 - 1.45 mm max height
SMALL OUTLINE TRANSISTOR
PKG
6X (1.1)
1
6X (0.6)
6
SYMM
5
2
3
2X(0.95)
4
(R0.05) TYP
(2.6)
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
SCALE:15X
4214840/C 06/2021
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
www.ti.com
PACKAGE OUTLINE
PW0020A
TSSOP - 1.2 mm max height
S
C
A
L
E
2
.
5
0
0
SMALL OUTLINE PACKAGE
SEATING
PLANE
C
6.6
6.2
TYP
A
0.1 C
PIN 1 INDEX AREA
18X 0.65
20
1
2X
5.85
6.6
6.4
NOTE 3
10
B
11
0.30
20X
4.5
4.3
NOTE 4
0.19
1.2 MAX
0.1
C A B
(0.15) TYP
SEE DETAIL A
0.25
GAGE PLANE
0.15
0.05
0.75
0.50
A
20
0 -8
DETAIL A
TYPICAL
4220206/A 02/2017
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed 0.15 mm per side.
4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.25 mm per side.
5. Reference JEDEC registration MO-153.
www.ti.com
EXAMPLE BOARD LAYOUT
PW0020A
TSSOP - 1.2 mm max height
SMALL OUTLINE PACKAGE
SYMM
20X (1.5)
(R0.05) TYP
20
1
20X (0.45)
SYMM
18X (0.65)
11
10
(5.8)
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE: 10X
METAL UNDER
SOLDER MASK
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL
EXPOSED METAL
EXPOSED METAL
0.05 MAX
ALL AROUND
0.05 MIN
ALL AROUND
NON-SOLDER MASK
DEFINED
SOLDER MASK
DEFINED
15.000
(PREFERRED)
SOLDER MASK DETAILS
4220206/A 02/2017
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
PW0020A
TSSOP - 1.2 mm max height
SMALL OUTLINE PACKAGE
20X (1.5)
SYMM
(R0.05) TYP
20
1
20X (0.45)
SYMM
18X (0.65)
10
11
(5.8)
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
SCALE: 10X
4220206/A 02/2017
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
www.ti.com
重要声明和免责声明
TI“按原样”提供技术和可靠性数据(包括数据表)、设计资源(包括参考设计)、应用或其他设计建议、网络工具、安全信息和其他资源,
不保证没有瑕疵且不做出任何明示或暗示的担保,包括但不限于对适销性、某特定用途方面的适用性或不侵犯任何第三方知识产权的暗示担
保。
这些资源可供使用 TI 产品进行设计的熟练开发人员使用。您将自行承担以下全部责任:(1) 针对您的应用选择合适的 TI 产品,(2) 设计、验
证并测试您的应用,(3) 确保您的应用满足相应标准以及任何其他功能安全、信息安全、监管或其他要求。
这些资源如有变更,恕不另行通知。TI 授权您仅可将这些资源用于研发本资源所述的 TI 产品的应用。严禁对这些资源进行其他复制或展示。
您无权使用任何其他 TI 知识产权或任何第三方知识产权。您应全额赔偿因在这些资源的使用中对 TI 及其代表造成的任何索赔、损害、成
本、损失和债务,TI 对此概不负责。
TI 提供的产品受 TI 的销售条款或 ti.com 上其他适用条款/TI 产品随附的其他适用条款的约束。TI 提供这些资源并不会扩展或以其他方式更改
TI 针对 TI 产品发布的适用的担保或担保免责声明。
TI 反对并拒绝您可能提出的任何其他或不同的条款。IMPORTANT NOTICE
邮寄地址:Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023,德州仪器 (TI) 公司
相关型号:
©2020 ICPDF网 联系我们和版权申明