LM118 MD8 [TI]
Military-grade, single, 40-V, 15-MHz operational amplifier with QML certification | Y | 0 | -55 to 125;型号: | LM118 MD8 |
厂家: | TEXAS INSTRUMENTS |
描述: | Military-grade, single, 40-V, 15-MHz operational amplifier with QML certification | Y | 0 | -55 to 125 放大器 运算放大器 放大器电路 |
文件: | 总19页 (文件大小:912K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LM118QML
LM118QML Operational Amplifier
Literature Number: SNOSAJ3
July 2005
LM118QML
Operational Amplifier
General Description
The LM118 is a precision high speed operational amplifier
designed for applications requiring wide bandwidth and high
slew rate. It features a factor of ten increase in speed over
general purpose devices without sacrificing DC perfor-
mance.
The high speed and fast settling time of this op amp makes
it useful in A/D converters, oscillators, active filters, sample
and hold circuits, or general purpose amplifiers. This device
is easy to apply and offers an order of magnitude better AC
performance than industry standards such as the LM709.
Features
The LM118 has internal unity gain frequency compensation.
This considerably simplifies its application since no external
components are necessary for operation. However, unlike
most internally compensated amplifiers, external frequency
compensation may be added for optimum performance. For
inverting applications, feed forward compensation will boost
the slew rate to over 150V/µs and almost double the band-
width. Overcompensation can be used with the amplifier for
greater stability when maximum bandwidth is not needed.
Further, a single capacitor can be added to reduce the 0.1%
settling time to under 1 µs.
n 15 MHz small signal bandwidth
n Guaranteed 50V/µs slew rate
n Maximum bias current of 250 nA
n Operates from supplies of 5V to 20V
n Internal frequency compensation
n Input and output overload protected
n Pin compatible with general purpose op amps
Ordering Information
NS Part Number
JAN Part Number
NS Package Number
Package Description
8LD TO-99 Metal Can
8LD CERDIP
LM118H/883
H08C
J08A
LM118J-8/883
LM118J/883
J14A
14LD CERDIP
LM118WG/883
WG10A
10LD Ceramic SOIC
Fast Voltage Follower
(Note 1)
20128313
Note 1: Do not hard-wire as voltage follower (R1 ≥ 5 kΩ)
© 2005 National Semiconductor Corporation
DS201283
www.national.com
Connection Diagram
Metal Can Package
(Note 2)
Dual-In-Line Package
20128302
20128324
Top View
See NS Package Number H08C
Top View
See NS Package Number J14A
Ceramic SOIC Package
Dual-In-Line Package
20128363
Top View
See NS Package Number WG10A
20128303
Top View
See NS Package Number J08A
Note 2: Pin connections shown on schematic diagram and typical applica-
tions are for TO-5 package.
www.national.com
2
Schematic Diagram
20128301
3
www.national.com
Absolute Maximum Ratings (Note 3)
Supply Voltage
20V
Power Dissipation (Note 4)
8 LD Metal Can
750mW
1000mW
8LD CERDIP
14LD CERDIP
1250mW
10LD Ceramic SOIC
Differential Input Current (Note 5)
Input Voltage (Note 6)
Output Short-Circuit Duration
Operating Temperature Range
Thermal Resistance
θJA
600mW
10 mA
15V
Continuous
−55˚C ≤ TA ≤ +125˚C
@
8 LD Metal Can (Still Air 0.5W)
160˚C/W
86˚C/W
120˚C/W
66˚C/W
87˚C/W
51˚C/W
198˚C/W
124˚C/W
@
8 LD Metal Can (500LF / Min Air flow 0.5W)
@
8LD CERDIP (Still Air 0.5W)
@
8LD CERDIP (500LF / Min Air flow 0.5W)
@
14LD CERDIP (Still Air 0.5W)
@
14LD CERDIP (500LF / Min Air flow 0.5W)
@
10LD Ceramic SOIC (Still Air 0.5W)
10LD Ceramic SOIC (500LF / Min Air flow 0.5W)
θJC
@
8 LD Metal Can
48˚C/W
17˚C/W
8LD CERDIP
14LD CERDIP
17˚C/W
10LD Ceramic SOIC
22˚C/W
Storage Temperature Range
Lead Temperature (Soldering, 10 seconds)
ESD Tolerance (Note 7)
−65˚C ≤ TA ≤ +150˚C
300˚C
2000V
Quality Conformance Inspection
Mil-Std-883, Method 5005; Group A
Subgroup
Description
Static tests at
Temp˚C
25
1
2
Static tests at
125
-55
25
3
Static tests at
4
Dynamic tests at
Dynamic tests at
Dynamic tests at
Functional tests at
Functional tests at
Functional tests at
Switching tests at
Switching tests at
Switching tests at
Settling time at
Settling time at
Settling time at
5
125
-55
25
6
7
8A
8B
9
125
-55
25
10
11
12
13
14
125
-55
25
125
-55
www.national.com
4
LM118
883 Electrical Characteristics
DC Parameters
The following conditions apply, unless otherwise specified.
DC
VCC
=
15V, VCM = 0V
Sub-
groups
1
Symbol
Parameter
Conditions
Notes
Min Max
Unit
VIO
Input Offset Voltage
VCM
VCC
VCC
=
=
=
11.5V, RS = 50Ω
-4.0 +4.0
-6.0 +6.0
-4.0 +4.0
-6.0 +6.0
-4.0 +4.0
-6.0 +6.0
-4.0 +4.0
-6.0 +6.0
mV
mV
mV
mV
mV
mV
mV
mV
nA
nA
nA
nA
nA
nA
nA
nA
nA
nA
nA
nA
dB
dB
2, 3
1
20V, RS = 50Ω
2, 3
1
20V, VCM
=
15V,
RS = 50Ω
2, 3
1
VCC
VCM
VCC
VCC
VCM
VCC
VCC
=
=
=
=
=
=
=
5V, RS = 50Ω
2, 3
1
IIO
Input Offset Current
11.5V, RS = 10KΩ
20V, RS = 10KΩ
5V, RS = 10KΩ
11.5V, RS= 10KΩ
20V, RS = 10KΩ
5V, RS = 10KΩ
-50
-100 +100
-50 +50
-100 +100
-50 +50
-100 +100
+50
2, 3
1
2, 3
1
2, 3
1
IIB
Input Bias Current
1.0
1.0
1.0
1.0
1.0
1.0
70
250
500
250
500
250
500
2, 3
1
2, 3
1
2, 3
1, 2, 3
1, 2, 3
PSRR
CMRR
Power Supply Rejection Ratio
+VCC = 20V to 5V, RS = 50Ω
-VCC = -20V to -5V, RS = 50Ω
70
Common Mode Rejection Ratio VCC
=
15V, VCM
=
11.5V,
80
dB
1, 2, 3
RS = 50Ω
<
<
+IOS
-IOS
Short Circuit Current
Short Circuit Current
t
t
25mS
25mS
-65
5.0
5.0
-5.0
65
mA
mA
1, 2, 3
1, 2
80
mA
3
ICC
Power Supply Current
VCC
=
20V
8.0
7.0
11
mA
1
mA
2
mA
3
1
VIO adj.
RI
Input Offset Voltage Adjust
Input Resistance
VCC
VCC
=
=
20V
15V
4.0
1.0
-4.0
mV
(Note 9)
MΩ
V
1
VI
Input Voltage Range
(Note 8) -11.5 +11.5
1, 2, 3
4
AVS
Large Signal Voltage Gain
RL = 2KΩ, VO = 0 to -10V
RL = 2KΩ, VO = 0 to +10V
RL= 2KΩ
(Note 10)
(Note 10)
(Note 10)
(Note 10)
50
25
V/mV
V/mV
V/mV
V/mV
V
5, 6
4
50
25
5, 6
4, 5, 6
VO
Output Voltage Swing
+12
-12
5
www.national.com
LM118
883 Electrical Characteristics (Continued)
AC Parameters
The following conditions apply parameters, unless otherwise specified.
AC
VCC
=
15V, VCM = 0V,
RS = 0Ω, RL = 2KΩ,, CL = 33pF
Sub-
groups
Symbol
Parameter
Conditions
Notes
Min Max
Unit
V/µS
V/µS
SR
Slew Rate
VCC
=
20V, VI = -5V to +5V,
20V, VI = +5V to -5V,
50
50
7
7
AV=1
VCC
=
AV=1
Note 3: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed
specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test
conditions.
Note 4: The maximum power dissipation must be derated at elevated temperatures and is dictated by T
(maximum junction temperature), θ (package junction
JA
Jmax
to ambient thermal resistance), and T (ambient temperature). The maximum allowable power dissipation at any temperature is P
= (T
- T )/θ or the
A
Dmax
Jmax A JA
number given in the Absolute Maximum Ratings, whichever is lower.
Note 5: The inputs are shunted with back-to-back diodes for over voltage protection. Therefore, excessive current will flow if a differential input voltage in excess
of 1V is applied between the inputs unless some limiting resistance is used.
Note 6: For supply voltages less than 15V, the absolute maximum input voltage is equal to the supply voltage.
Note 7: Human body model, 1.5 kΩ in series with 100 pF.
Note 8: Guaranteed by CMRR
Note 9: Guaranteed parameter not tested
Note 10: Datalog in K = V/mV
www.national.com
6
Typical Performance Characteristics
Input Current
Voltage Gain
20128326
20128328
20128330
20128325
Power Supply Rejection
Input Noise Voltage
20128327
Common Mode Rejection
Supply Current
20128329
7
www.national.com
Typical Performance Characteristics (Continued)
Closed Loop Output
Impedance
Current Limiting
Unity Gain Bandwidth
Inverter Settling Time
20128332
20128334
20128336
20128331
Input Current
20128333
Voltage Follower Slew Rate
20128335
www.national.com
8
Typical Performance Characteristics (Continued)
Large Signal Frequency
Response
Open Loop Frequency
Response
20128337
20128338
Voltage Follower Pulse
Response
Large Signal Frequency
Response
20128340
20128339
Open Loop Frequency
Response
Inverter Pulse Response
20128342
20128341
9
www.national.com
Auxiliary Circuits
Offset Balancing
Feedforward Compensation
for Greater Inverting Slew Rate
(Note 11)
20128310
Isolating Large Capacitive Loads
20128308
*Balance circuit necessary for increased slew.
Note 11: Slew rate typically 150V/µs.
Compensation for Minimum Settling Time
(Note 12)
20128311
Overcompensation
20128312
20128309
Note 12: Slew and settling time to 0.1% for a 10V step change is 800 ns.
www.national.com
10
Typical Applications
Fast Voltage Follower
(Note 13)
20128313
Integrator or Slow Inverter
20128314
C
F
= Large
(C ≥ 50 pF)
F
*Do not hard-wire as integrator or slow inverter; insert a 10k-5 pF network in series with the input, to prevent oscillation.
Note 13: Do not hard-wire as voltage follower (R1 ≥ 5 kΩ)
Differential Amplifier
Fast Summing Amplifier
20128316
20128315
11
www.national.com
Typical Applications (Continued)
Fast Sample and Hold
20128318
D/A Converter Using Ladder Network
20128319
*Optional — Reduces settling time.
www.national.com
12
Typical Applications (Continued)
Four Quadrant Multiplier
20128317
∆Output zero.
*“Y” zero
+“X” zero
‡
Full scale adjust.
D/A Converter Using Binary Weighted Network
20128320
*Optional — Reduces settling time.
13
www.national.com
Typical Applications (Continued)
Fast Summing Amplifier with Low Input Current
20128321
Instrumentation Amplifier
Wein Bridge Sine Wave Oscillator
20128322
20128323
www.national.com
14
Revision History Section
Date
Released
07/12/05
Revision
Section
Originator
Changes
A
New Release, Corporate format
L. Lytle
1 MDS data sheet, MNLM118–X Rev 0A0
was converted into the Corp. datasheet
format. MDS datasheet will be archived.
15
www.national.com
Physical Dimensions inches (millimeters) unless otherwise noted
Metal Can Package (H)
NS Package Number H08C
Ceramic Dual-In-Line Package (J)
NS Package Number J08A
Ceramic Dual-In-Line Package (J)
NS Package Number J14A
www.national.com
16
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
Ceramic SOIC (WG)
NS Package Number WG10A
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves
the right at any time without notice to change said circuitry and specifications.
For the most current product information visit us at www.national.com.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS
WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR
CORPORATION. As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body, or
(b) support or sustain life, and whose failure to perform when
properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to result
in a significant injury to the user.
2. A critical component is any component of a life support
device or system whose failure to perform can be reasonably
expected to cause the failure of the life support device or
system, or to affect its safety or effectiveness.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products
Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain
no ‘‘Banned Substances’’ as defined in CSP-9-111S2.
Leadfree products are RoHS compliant.
National Semiconductor
Americas Customer
Support Center
National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
National Semiconductor
Asia Pacific Customer
Support Center
National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: new.feedback@nsc.com
Tel: 1-800-272-9959
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
Email: ap.support@nsc.com
Email: jpn.feedback@nsc.com
Tel: 81-3-5639-7560
www.national.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Audio
Applications
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
www.ti.com/industrial
www.ti.com/medical
www.ti.com/security
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
Medical
Security
Logic
Space, Avionics and Defense www.ti.com/space-avionics-defense
Transportation and Automotive www.ti.com/automotive
Power Mgmt
Microcontrollers
RFID
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
Video and Imaging
www.ti.com/video
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明