LM158J/NOPB [TI]
DUAL OP-AMP, 7000uV OFFSET-MAX, 1MHz BAND WIDTH, CDIP8, CERDIP-8;
| 型号： | LM158J/NOPB |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | DUAL OP-AMP, 7000uV OFFSET-MAX, 1MHz BAND WIDTH, CDIP8, CERDIP-8 放大器 CD |
| 文件： | 总26页 (文件大小：1039K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
National Semiconductor is now part of
Texas Instruments.
Search http://www.ti.com/ for the latest technical
information and details on our current products and services.
October 2005
LM158/LM258/LM358/LM2904
Low Power Dual Operational Amplifiers
General Description
Advantages
n Two internally compensated op amps
n Eliminates need for dual supplies
The LM158 series consists of two independent, high gain,
internally frequency compensated operational amplifiers
which were designed specifically to operate from a single
power supply over a wide range of voltages. Operation from
split power supplies is also possible and the low power
supply current drain is independent of the magnitude of the
power supply voltage.
n Allows direct sensing near GND and VOUT also goes to
GND
n Compatible with all forms of logic
n Power drain suitable for battery operation
Application areas include transducer amplifiers, dc gain
blocks and all the conventional op amp circuits which now
can be more easily implemented in single power supply
systems. For example, the LM158 series can be directly
operated off of the standard +5V power supply voltage which
is used in digital systems and will easily provide the required
interface electronics without requiring the additional 15V
power supplies.
Features
n Available in 8-Bump micro SMD chip sized package,
(See AN-1112)
n Internally frequency compensated for unity gain
n Large dc voltage gain: 100 dB
n Wide bandwidth (unity gain): 1 MHz
(temperature compensated)
n Wide power supply range:
— Single supply: 3V to 32V
The LM358 and LM2904 are available in a chip sized pack-
age (8-Bump micro SMD) using National’s micro SMD pack-
age technology.
— or dual supplies:
1.5V to 16V
n Very low supply current drain (500 µA)—essentially
independent of supply voltage
n Low input offset voltage: 2 mV
n Input common-mode voltage range includes ground
n Differential input voltage range equal to the power
supply voltage
Unique Characteristics
n In the linear mode the input common-mode voltage
range includes ground and the output voltage can also
swing to ground, even though operated from only a
single power supply voltage.
n Large output voltage swing
n The unity gain cross frequency is temperature
compensated.
n The input bias current is also temperature compensated.
Voltage Controlled Oscillator (VCO)
00778723
© 2005 National Semiconductor Corporation
DS007787
www.national.com
Distributors for availability and specifications.
Absolute Maximum Ratings (Note 9)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
LM158/LM258/LM358
LM2904
LM158A/LM258A/LM358A
Supply Voltage, V+
Differential Input Voltage
Input Voltage
32V
32V
26V
26V
−0.3V to +32V
−0.3V to +26V
Power Dissipation (Note 1)
Molded DIP
830 mW
550 mW
530 mW
435mW
830 mW
530 mW
Metal Can
Small Outline Package (M)
micro SMD
Output Short-Circuit to GND
(One Amplifier) (Note 2)
V+ ≤ 15V and TA = 25˚C
Continuous
50 mA
Continuous
50 mA
<
Input Current (VIN −0.3V) (Note 3)
Operating Temperature Range
LM358
0˚C to +70˚C
−25˚C to +85˚C
−55˚C to +125˚C
−65˚C to +150˚C
−40˚C to +85˚C
LM258
LM158
Storage Temperature Range
Lead Temperature, DIP
(Soldering, 10 seconds)
Lead Temperature, Metal Can
(Soldering, 10 seconds)
Soldering Information
Dual-In-Line Package
Soldering (10 seconds)
Small Outline Package
Vapor Phase (60 seconds)
Infrared (15 seconds)
−65˚C to +150˚C
260˚C
260˚C
300˚C
300˚C
260˚C
260˚C
215˚C
220˚C
215˚C
220˚C
See AN-450 “Surface Mounting Methods and Their Effect on Product Reliability” for other methods of soldering
surface mount devices.
ESD Tolerance (Note 10)
250V
250V
Electrical Characteristics
V+ = +5.0V, unless otherwise stated
Parameter
Conditions
LM158A
LM358A
LM158/LM258
Units
Min Typ Max Min Typ Max Min Typ Max
Input Offset Voltage
Input Bias Current
(Note 5), TA = 25˚C
1
2
2
3
2
5
mV
nA
IIN(+) or IIN(−), TA = 25˚C,
VCM = 0V, (Note 6)
20
50
45
100
45
150
Input Offset Current
Input Common-Mode
Voltage Range
IIN(+) − IIN(−), VCM = 0V, TA = 25˚C
V+ = 30V, (Note 7)
(LM2904, V+ = 26V), TA = 25˚C
2
10
V+−1.5
5
30
V+−1.5
3
30
V+−1.5
nA
V
0
0
0
Supply Current
Over Full Temperature Range
∞
on All Op Amps
RL
=
V+ = 30V (LM2904 V+ = 26V)
V+ = 5V
1
2
1
2
1
2
mA
mA
0.5
1.2
0.5
1.2
0.5
1.2
www.national.com
2
Electrical Characteristics
V+ = +5.0V, unless otherwise stated
Parameter
Conditions
LM358
Typ
2
LM2904
Units
Min
Max
7
Min
Typ
2
Max
7
Input Offset Voltage
Input Bias Current
(Note 5) , TA = 25˚C
mV
nA
IIN(+) or IIN(−), TA = 25˚C,
VCM = 0V, (Note 6)
45
250
45
250
Input Offset Current
Input Common-Mode
Voltage Range
IIN(+) − IIN(−), VCM = 0V, TA = 25˚C
V+ = 30V, (Note 7)
(LM2904, V+ = 26V), TA = 25˚C
5
50
V+−1.5
5
50
V+−1.5
nA
V
0
0
Supply Current
Over Full Temperature Range
∞
on All Op Amps
RL
=
V+ = 30V (LM2904 V+ = 26V)
V+ = 5V
1
2
1
2
mA
mA
0.5
1.2
0.5
1.2
Electrical Characteristics
V+ = +5.0V, (Note 4), unless otherwise stated
LM158A
LM358A
LM158/LM258
Units
Parameter
Conditions
Min Typ Max Min Typ Max Min Typ Max
Large Signal Voltage
Gain
V+ = 15V, TA = 25˚C,
RL ≥ 2 kΩ, (For VO = 1V
to 11V)
50 100 25 100 50 100
V/mV
dB
Common-Mode
Rejection Ratio
Power Supply
Rejection Ratio
TA = 25˚C,
70
85
65
85
70
85
VCM = 0V to V+−1.5V
V+ = 5V to 30V
(LM2904, V+ = 5V
to 26V), TA = 25˚C
f = 1 kHz to 20 kHz, TA = 25˚C
65 100
−120
65 100
−120
65 100
−120
dB
Amplifier-to-Amplifier
Coupling
dB
(Input Referred), (Note 8)
+
Output Current
Source VIN = 1V,
−
VIN = 0V,
V+ = 15V,
20
10
12
40
20
20
10
12
40
20
20
10
12
40
20
mA
mA
µA
VO = 2V, TA = 25˚C
−
+
Sink VIN = 1V, VIN = 0V
V+ = 15V, TA = 25˚C,
VO = 2V
−
VIN = 1V,
+
VIN = 0V
50
40
7
50
40
7
50
40
7
TA = 25˚C, VO = 200 mV,
V+ = 15V
Short Circuit to Ground
TA = 25˚C, (Note 2),
V+ = 15V
60
4
60
5
60
7
mA
mV
Input Offset Voltage
Input Offset Voltage
Drift
(Note 5)
RS = 0Ω
15
20
µV/˚C
nA
Input Offset Current
Input Offset Current
Drift
IIN(+) − IIN(−)
30
75
100
RS = 0Ω
10
40
200
100
V+−2
10
40
300
200
V+−2
10
40
pA/˚C
nA
Input Bias Current
Input Common-Mode
Voltage Range
IIN(+) or IIN(−)
300
V+ = 30 V, (Note 7)
(LM2904, V+ = 26V)
0
0
0
V+−2
V
3
www.national.com
Electrical Characteristics (Continued)
V+ = +5.0V, (Note 4), unless otherwise stated
LM158A
LM358A
LM158/LM258
Units
Parameter
Conditions
Min Typ Max Min Typ Max Min Typ Max
Large Signal Voltage
Gain
V+ = +15V
(VO = 1V to 11V)
25
15
25
V/mV
RL ≥ 2 kΩ
Output
Voltage
Swing
VOH V+ = +30V
RL = 2 kΩ
26
27
26
27
26
27
V
V
(LM2904, V+ = 26V) RL = 10 kΩ
VOL V+ = 5V, RL = 10 kΩ
28
5
28
5
28
5
20
20
20
mV
+
−
Output Current
Source VIN = +1V, VIN = 0V,
V+ = 15V, VO = 2V
10
10
20
15
10
5
20
8
10
5
20
8
mA
mA
−
+
Sink VIN = +1V, VIN = 0V,
V+ = 15V, VO = 2V
Electrical Characteristics
V+ = +5.0V, (Note 4), unless otherwise stated
LM358
Typ
LM2904
Typ
Units
Parameter
Conditions
Min
Max
Min
Max
Large Signal Voltage
Gain
V+ = 15V, TA = 25˚C,
RL ≥ 2 kΩ, (For VO = 1V
to 11V)
25
100
85
25
100
70
V/mV
dB
Common-Mode
Rejection Ratio
Power Supply
Rejection Ratio
TA = 25˚C,
65
65
50
50
VCM = 0V to V+−1.5V
V+ = 5V to 30V
(LM2904, V+ = 5V
to 26V), TA = 25˚C
f = 1 kHz to 20 kHz, TA = 25˚C
100
−120
100
−120
dB
Amplifier-to-Amplifier
Coupling
dB
(Input Referred), (Note 8)
+
Output Current
Source VIN = 1V,
−
VIN = 0V,
V+ = 15V,
20
10
12
40
20
20
10
12
40
20
mA
mA
µA
VO = 2V, TA = 25˚C
−
+
Sink VIN = 1V, VIN = 0V
V+ = 15V, TA = 25˚C,
VO = 2V
−
VIN = 1V,
+
VIN = 0V
50
40
7
50
40
TA = 25˚C, VO = 200 mV,
V+ = 15V
Short Circuit to Ground
TA = 25˚C, (Note 2),
V+ = 15V
60
9
60
10
mA
mV
Input Offset Voltage
Input Offset Voltage
Drift
(Note 5)
RS = 0Ω
7
µV/˚C
nA
Input Offset Current
Input Offset Current
Drift
IIN(+) − IIN(−)
150
45
10
40
200
RS = 0Ω
10
40
pA/˚C
nA
Input Bias Current
Input Common-Mode
Voltage Range
IIN(+) or IIN(−)
500
500
V+ = 30 V, (Note 7)
(LM2904, V+ = 26V)
0
V+−2
0
V+ −2
V
www.national.com
4
Electrical Characteristics (Continued)
V+ = +5.0V, (Note 4), unless otherwise stated
LM358
Typ
LM2904
Typ
Units
Parameter
Conditions
Min
Max
Min
Max
Large Signal Voltage
Gain
V+ = +15V
(VO = 1V to 11V)
15
15
V/mV
RL ≥ 2 kΩ
Output
VOH V+ = +30V
RL = 2 kΩ
26
27
22
23
V
V
Voltage
(LM2904, V+ = 26V)
RL = 10 kΩ
28
5
24
5
Swing
VOL V+ = 5V, RL = 10 kΩ
20
100
mV
+
−
Output Current
Source VIN = +1V, VIN = 0V,
V+ = 15V, VO = 2V
10
5
20
8
10
5
20
8
mA
mA
−
+
Sink VIN = +1V, VIN = 0V,
V+ = 15V, VO = 2V
Note 1: For operating at high temperatures, the LM358/LM358A, LM2904 must be derated based on a +125˚C maximum junction temperature and a thermal
resistance of 120˚C/W for MDIP, 182˚C/W for Metal Can, 189˚C/W for Small Outline package, and 230˚C/W for micro SMD, which applies for the device soldered
in a printed circuit board, operating in a still air ambient. The LM258/LM258A and LM158/LM158A can be derated based on a +150˚C maximum junction temperature.
The dissipation is the total of both amplifiers — use external resistors, where possible, to allow the amplifier to saturate or to reduce the power which is dissipated
in the integrated circuit.
+
Note 2: Short circuits from the output to V can cause excessive heating and eventual destruction. When considering short cirucits to ground, the maximum output
+
current is approximately 40 mA independent of the magnitude of V . At values of supply voltage in excess of +15V, continuous short-circuits can exceed the power
dissipation ratings and cause eventual destruction. Destructive dissipation can result from simultaneous shorts on all amplifiers.
Note 3: This input current will only exist when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of the input PNP
transistors becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is also lateral NPN parasitic transistor action
+
on the IC chip. This transistor action can cause the output voltages of the op amps to go to the V voltage level (or to ground for a large overdrive) for the time duration
that an input is driven negative. This is not destructive and normal output states will re-establish when the input voltage, which was negative, again returns to a value
greater than −0.3V (at 25˚C).
Note 4: These specifications are limited to −55˚C ≤ T ≤ +125˚C for the LM158/LM158A. With the LM258/LM258A, all temperature specifications are limited to
A
−25˚C ≤ T ≤ +85˚C, the LM358/LM358A temperature specifications are limited to 0˚C ≤ T ≤ +70˚C, and the LM2904 specifications are limited to −40˚C ≤ T ≤
A
A
A
+85˚C.
+
+
+
Note 5: V . 1.4V, R = 0Ω with V from 5V to 30V; and over the full input common-mode range (0V to V −1.5V) at 25˚C. For LM2904, V from 5V to 26V.
O
S
Note 6: The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the output so
no loading change exists on the input lines.
Note 7: The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (at 25˚C). The upper end of the
+
common-mode voltage range is V −1.5V (at 25˚C), but either or both inputs can go to +32V without damage (+26V for LM2904), independent of the magnitude of
+
V .
Note 8: Due to proximity of external components, insure that coupling is not originating via stray capacitance between these external parts. This typically can be
detected as this type of capacitance increases at higher frequencies.
Note 9: Refer to RETS158AX for LM158A military specifications and to RETS158X for LM158 military specifications.
Note 10: Human body model, 1.5 kΩ in series with 100 pF.
5
www.national.com
Typical Performance Characteristics
Input Voltage Range
Input Current
00778734
00778735
Supply Current
Voltage Gain
00778736
00778737
Open Loop Frequency Response
Common-Mode Rejection Ratio
00778738
00778739
www.national.com
6
Typical Performance Characteristics (Continued)
Voltage Follower Pulse Response
Voltage Follower Pulse Response (Small Signal)
00778741
00778740
Large Signal Frequency Response
Output Characteristics Current Sourcing
00778742
00778743
Output Characteristics Current Sinking
Current Limiting
00778744
00778745
7
www.national.com
Typical Performance Characteristics (Continued)
Input Current (LM2902 only)
Voltage Gain (LM2902 only)
00778746
00778747
Application Hints
The LM158 series are op amps which operate with only a
single power supply voltage, have true-differential inputs,
and remain in the linear mode with an input common-mode
voltage of 0 VDC. These amplifiers operate over a wide range
of power supply voltage with little change in performance
characteristics. At 25˚C amplifier operation is possible down
Capacitive loads which are applied directly to the output of
the amplifier reduce the loop stability margin. Values of 50
pF can be accomodated using the worst-case non-inverting
unity gain connection. Large closed loop gains or resistive
isolation should be used if larger load capacitance must be
driven by the amplifier.
to a minimum supply voltage of 2.3 VDC
.
The bias network of the LM158 establishes a drain current
which is independent of the magnitude of the power supply
Precautions should be taken to insure that the power supply
for the integrated circuit never becomes reversed in polarity
or that the unit is not inadvertently installed backwards in a
test socket as an unlimited current surge through the result-
ing forward diode within the IC could cause fusing of the
internal conductors and result in a destroyed unit.
voltage over the range of 3 VDC to 30 VDC
.
Output short circuits either to ground or to the positive power
supply should be of short time duration. Units can be de-
stroyed, not as a result of the short circuit current causing
metal fusing, but rather due to the large increase in IC chip
dissipation which will cause eventual failure due to exces-
sive function temperatures. Putting direct short-circuits on
more than one amplifier at a time will increase the total IC
power dissipation to destructive levels, if not properly pro-
tected with external dissipation limiting resistors in series
with the output leads of the amplifiers. The larger value of
output source current which is available at 25˚C provides a
larger output current capability at elevated temperatures
(see typical performance characteristics) than a standard IC
op amp.
Large differential input voltages can be easily accomodated
and, as input differential voltage protection diodes are not
needed, no large input currents result from large differential
input voltages. The differential input voltage may be larger
than V+ without damaging the device. Protection should be
provided to prevent the input voltages from going negative
more than −0.3 VDC (at 25˚C). An input clamp diode with a
resistor to the IC input terminal can be used.
To reduce the power supply current drain, the amplifiers
have a class A output stage for small signal levels which
converts to class B in a large signal mode. This allows the
amplifiers to both source and sink large output currents.
Therefore both NPN and PNP external current boost transis-
tors can be used to extend the power capability of the basic
amplifiers. The output voltage needs to raise approximately
1 diode drop above ground to bias the on-chip vertical PNP
transistor for output current sinking applications.
The circuits presented in the section on typical applications
emphasize operation on only a single power supply voltage.
If complementary power supplies are available, all of the
standard op amp circuits can be used. In general, introduc-
ing a pseudo-ground (a bias voltage reference of V+/2) will
allow operation above and below this value in single power
supply systems. Many application circuits are shown which
take advantage of the wide input common-mode voltage
range which includes ground. In most cases, input biasing is
not required and input voltages which range to ground can
easily be accommodated.
For ac applications, where the load is capacitively coupled to
the output of the amplifier, a resistor should be used, from
the output of the amplifier to ground to increase the class A
bias current and prevent crossover distortion. Where the
load is directly coupled, as in dc applications, there is no
crossover distortion.
www.national.com
8
Connection Diagrams
DIP/SO Package
Metal Can Package
00778701
00778702
Top View
Top View
8-Bump micro SMD
00778755
Top View
(Bump Side Down)
LM358BP micro SMD Marking Orientation
LM2904IBP micro SMD Marking Orientation
00778757
00778756
Top View
Top View
LM358TP micro SMD Marking Orientation
LM2904ITP micro SMD Marking Orientation
00778758
00778759
Top View
Top View
9
www.national.com
Ordering Information
Temperature Range
Package
NSC Drawing
M08A
−55˚C to 125˚C
−25˚C to 85˚C
0˚C to 70˚C
LM358AM
LM358AMX
LM358M
−40˚C to 85˚C
LM2904M
SO-8
LM2904MX
LM358MX
LM358AN
LM358N
8-Pin Molded DIP
8-Pin Ceramic DIP
LM2904N
N08E
LM158AJ/883(Note 11)
LM158J/883(Note 11)
LM158J
J08A
LM158AJLQML(Note 12)
LM158AJQMLV(Note 12)
LM158AH/883(Note 11)
LM158H/883(Note 11)
LM158AH
TO-5, 8-Pin Metal
Can
LM258H
LM358H
H08C
LM158H
LM158AHLQML(Note 12)
LM158AHLQMLV(Note 12)
8-Bump micro
SMD
LM358BP
LM358BPX
LM358TP
LM2904IBP
LM2904IBPX
LM2904ITP
LM2904ITPX
BPA08AAB
0.85 mm Thick
8-Bump micro
SMD
TPA08AAA
LM358TPX
0.50 mm Thick
Lead Free
14-Pin Ceramic
SOIC
LM158AWG/883
WG10A
Note 11: LM158 is available per SMD #5962-8771001
LM158A is available per SMD #5962-8771002
Note 12: See STD Mil DWG 5962L87710 for Radiation Tolerant Devices
www.national.com
10
Typical Single-Supply Applications
(V+ = 5.0 VDC
Non-Inverting DC Gain (0V Output)
)
00778706
00778707
*
R not needed due to temperature independent I
IN
DC Summing Amplifier
(VIN’S ≥ 0 VDC and VO ≥ 0 VDC
)
Power Amplifier
00778709
00778708
V
A
= 0 V
for V = 0 V
DC IN DC
O
Where: V = V + V − V − V
4
O
1
2
3
= 10
V
>
(V + V ) ≥ (V + V ) to keep V
0 V
DC
1
2
3
4
O
11
www.national.com
Typical Single-Supply Applications (V+ = 5.0 VDC) (Continued)
“BI-QUAD” RC Active Bandpass Filter
00778710
f
= 1 kHz
o
Q = 50
= 100 (40 dB)
A
v
Fixed Current Sources
Lamp Driver
00778712
00778711
www.national.com
12
Typical Single-Supply Applications (V+ = 5.0 VDC) (Continued)
LED Driver
Current Monitor
00778713
00778714
*
(Increase R1 for I small)
L
+
V
L
≤ V −2V
Driving TTL
Voltage Follower
00778715
00778717
V
= V
IN
O
Pulse Generator
00778716
13
www.national.com
Typical Single-Supply Applications (V+ = 5.0 VDC) (Continued)
Squarewave Oscillator
Pulse Generator
00778718
00778719
Low Drift Peak Detector
00778720
HIGH Z
IN
LOW Z
OUT
www.national.com
14
Typical Single-Supply Applications (V+ = 5.0 VDC) (Continued)
High Compliance Current Sink
Comparator with Hysteresis
00778722
00778721
I
= 1 amp/volt V
IN
O
(Increase R for I small)
E
O
Voltage Controlled Oscillator (VCO)
00778723
+
*
WIDE CONTROL VOLTAGE RANGE: 0 V
≤ V ≤ 2 (V −1.5V
)
DC
DC
C
15
www.national.com
Typical Single-Supply Applications (V+ = 5.0 VDC) (Continued)
AC Coupled Inverting Amplifier
00778724
Ground Referencing a Differential Input Signal
00778725
www.national.com
16
Typical Single-Supply Applications (V+ = 5.0 VDC) (Continued)
AC Coupled Non-Inverting Amplifier
00778726
A
v
= 11 (As Shown)
DC Coupled Low-Pass RC Active Filter
00778727
f
= 1 kHz
o
Q = 1
= 2
A
V
17
www.national.com
Typical Single-Supply Applications (V+ = 5.0 VDC) (Continued)
Bandpass Active Filter
00778728
f
= 1 kHz
o
Q = 25
High Input Z, DC Differential Amplifier
00778729
www.national.com
18
Typical Single-Supply Applications (V+ = 5.0 VDC) (Continued)
Photo Voltaic-Cell Amplifier
Bridge Current Amplifier
00778730
00778733
High Input Z Adjustable-Gain
DC Instrumentation Amplifier
00778731
19
www.national.com
Typical Single-Supply Applications (V+ = 5.0 VDC) (Continued)
Using Symmetrical Amplifiers to
Reduce Input Current (General Concept)
00778732
Schematic Diagram (Each Amplifier)
00778703
www.national.com
20
Physical Dimensions inches (millimeters) unless otherwise noted
Metal Can Package (H)
NS Package Number H08C
Cerdip Package (J)
NS Package Number J08A
21
www.national.com
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
SOIC Package (M)
NS Package Number M08A
Molded Dip Package (N)
NS Package Number N08E
www.national.com
22
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
Order Number LM158AWG/883
NS Package Number WG10A
23
www.national.com
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
NOTES: UNLESS OTHERWISE SPECIFIED
1. EPOXY COATING
2. 63Sn/37Pb EUTECTIC BUMP
3. RECOMMEND NON-SOLDER MASK DEFINED LANDING PAD.
4. PIN A1 IS ESTABLISHED BY LOWER LEFT CORNER WITH RESPECT TO TEXT ORIENTATION REMAINING PINS ARE NUMBERED
COUNTERCLOCKWISE.
5. XXX IN DRAWING NUMBER REPRESENTS PACKAGE SIZE VARIATION WHERE X IS PACKAGE WIDTH, X IS PACKAGE LENGTH AND X IS
1
2
3
PACKAGE HEIGHT.
6. REFERENCE JEDEC REGISTRATION MO-211, VARIATION BC.
8-Bump micro SMD
NS Package Number BPA08AAB
X1 = 1.285 X2 = 1.285 X3 = 0.850
www.national.com
24
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
NOTES: UNLESS OTHERWISE SPECIFIED
1. EPOXY COATING
2. RECOMMEND NON-SOLDER MASK DEFINED LANDING PAD.
3. PIN A1 IS ESTABLISHED BY LOWER LEFT CORNER WITH RESPECT TO TEXT ORIENTATION REMAINING PINS ARE NUMBERED
COUNTERCLOCKWISE.
4. XXX IN DRAWING NUMBER REPRESENTS PACKAGE SIZE VARIATION WHERE X IS PACKAGE WIDTH, X IS PACKAGE LENGTH AND X IS
1
2
3
PACKAGE HEIGHT.
5. REFERENCE JEDEC REGISTRATION MO-211, VARIATION BC.
8-Bump micro SMD Lead Free
NS Package Number TPA08AAA
X1 = 1.285 X2 = 1.285 X3 = 0.500
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves
the right at any time without notice to change said circuitry and specifications.
For the most current product information visit us at www.national.com.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS
WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR
CORPORATION. As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body, or
(b) support or sustain life, and whose failure to perform when
properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to result
in a significant injury to the user.
2. A critical component is any component of a life support
device or system whose failure to perform can be reasonably
expected to cause the failure of the life support device or
system, or to affect its safety or effectiveness.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products
Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain
no ‘‘Banned Substances’’ as defined in CSP-9-111S2.
Leadfree products are RoHS compliant.
National Semiconductor
Americas Customer
Support Center
National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
National Semiconductor
Asia Pacific Customer
Support Center
National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: new.feedback@nsc.com
Tel: 1-800-272-9959
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
Email: ap.support@nsc.com
Email: jpn.feedback@nsc.com
Tel: 81-3-5639-7560
www.national.com
©2020 ICPDF网 联系我们和版权申明