LM185E-1.2/883 [TI]
LM185-1.2QML Micropower Voltage Reference Diode; LM185-1.2QML微功耗电压基准二极管型号: | LM185E-1.2/883 |
厂家: | TEXAS INSTRUMENTS |
描述: | LM185-1.2QML Micropower Voltage Reference Diode |
文件: | 总13页 (文件大小:726K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LM185-1.2QML
LM185-1.2QML Micropower Voltage Reference Diode
Literature Number: SNVS384
October 2005
LM185-1.2QML
Micropower Voltage Reference Diode
The extremely low power drain of the LM185-1.2 makes it
useful for micropower circuitry. This voltage reference can be
used to make portable meters, regulators or general purpose
analog circuitry with battery life approaching shelf life.
General Description
The LM185-1.2 is a micropower 2-terminal band-gap voltage
regulator diodes. Operating over a 10µA to 20mA current
range, it features exceptionally low dynamic impedance and
good temperature stability. On-chip trimming is used to pro-
vide tight voltage tolerance. Since the LM185-1.2 band-gap
reference uses only transistors and resistors, low noise and
good long term stability result.
Further, the wide operating current allows it to replace older
references with a tighter tolerance part.
Features
n Operating current of 10µA to 20mA
n 1Ω maximum dynamic impedance (typical)
n Low temperature coefficient
n Low voltage reference - 1.235V
Careful design of the LM185-1.2 has made the device ex-
ceptionally tolerant of capacitive loading, making it easy to
use in almost any reference application. The wide dynamic
operating range allows its use with widely varying supplies
with excellent regulation.
Ordering Information
NS Part Number
LM185E-1.2/883
LM185H-1.2-SMD
LM185H-1.2-QV
JAN Part Number
5962–87594012A
5962–8759401XA
5962–8759401VXA
5962–8759401YA
5962–8759405XA
5962–8759401VYA
NS Package Number
Package Description
20LD LCC
E20A
H02A
2 LD T0–46
H02A
2 LD T0–46
LM185WG-1.2/883
LM185BYH-1.2-SMD
LM185WG-1.2-QV
WG10A
H02A
10LD Ceramic SOIC
2 LD T0–46
WG10A
10LD Ceramic SOIC
Connection Diagrams
TO-46
Hermetic Leadless Chip Carrier (E)
Metal Can Package (H)
20156106
Bottom View
20156135
See NS Package Number E20A
See NS Package Number H02A
© 2005 National Semiconductor Corporation
DS201561
www.national.com
Connection Diagrams (Continued)
Ceramic SOIC (WG)
20156134
See NS Package Number WG10A
Schematic Diagram
20156107
www.national.com
2
Absolute Maximum Ratings (Note 1)
Reverse Current
30mA
10mA
Forward Current
Operating Temperature Range
Maximum Junction Temperature (TJmax) (Note 2)
Storage Temperature
Lead Temperature (Soldering 10 Seconds)
Ceramic SOIC
−55˚C ≤ TA ≤ +125˚C
+150˚C
−55˚C ≤ TA ≤ +150˚C
260˚C
300˚C
300˚C
TO-46 package
20LD LCC package
Thermal Resistance
θJA
Metal Can (Still Air)
Metal Can (500LF / Min Air Flow)
20LD LCC (Still Air)
20LD LCC (500LF / Min Air Flow)
Ceramic SOIC (Still Air)
Ceramic SOIC (500LF / Min Air Flow)
θJC
300˚C/W
139˚C/W
100˚C/W
73˚C/W
194˚C/W
128˚C/W
Metal Can
57˚C/W
25˚C/W
23˚C/W
20LD LCC
Ceramic SOIC
Package Weight (Typical)
Metal Can
TBD
TBD
20LD LCC
Ceramic SOIC
210mg
4KV
ESD Tolerance (Note 3)
Quality Conformance Inspection
Mil-Std-883, Method 5005 - Group A
Subgroup
Description
Static tests at
Temp ˚C
25
1
2
Static tests at
125
-55
25
3
Static tests at
4
Dynamic tests at
Dynamic tests at
Dynamic tests at
Functional tests at
Functional tests at
Functional tests at
Switching tests at
Switching tests at
Switching tests at
Settling time at
Settling time at
Settling time at
5
125
-55
25
6
7
8A
8B
9
125
-55
25
10
11
12
13
14
125
-55
25
125
-55
3
www.national.com
LM185–1.2 Electrical Characteristics
DC Parameters
Sub-
groups
Symbol
VRef
Parameter
Conditions
Notes
Min Max
Units
Reverse Breakdown Voltage
IR = 10µA
IR = 20µA
IR = 1mA
1.223 1.247
1.205 1.26
1.223 1.247
1.205 1.26
1.223 1.247
1.205 1.26
V
V
1
2, 3
1
V
V
2, 3
1
IR = 20mA
V
V
2, 3
1
∆VRef / ∆IR Reverse Breakdown Voltage
10µA ≤ IR ≤ 1mA
20µA ≤ IR ≤ 1mA
1mA ≤ IR ≤ 20mA
-1.0
-1.5
1.0
1.5
mV
mV
mV
mV
V
Change with Current
2, 3
1
-10.0 10.0
-20.0 20.0
2, 3
1
VF
Forward Bias Voltage
IF = 2mA
-1.0
-0.4
DC Drift Parameters
Delta calculations performed on QMLV devices at group B , subgroup 5, unless otherwise specified on the IPI.
Sub-
groups
Symbol
VR
Parameter
Conditions
Notes
Min Max
Units
Reverse Breakdown Voltage
IR = 10µA
IR = 20mA
-0.01 0.01
-0.01 0.01
V
V
1
1
LM185BY–1.2 Electrical Characteristics
DC Parameters
Sub-
groups
1
Symbol
VRef
Parameter
Conditions
Notes
Min Max
Units
Reverse Breakdown Voltage
IR = 10µA
IR = 20µA
IR = 1mA
1.223 1.247
1.205 1.26
1.223 1.247
1.205 1.26
1.223 1.247
1.205 1.26
V
V
2, 3
1
V
V
2, 3
1
IR = 20mA
V
V
2, 3
1
∆VRef / ∆IR Reverse Breakdown Voltage
10µA ≤ IR ≤ 1mA
20µA ≤ IR ≤ 1mA
1mA ≤ IR ≤ 20mA
-1.0
-1.5
1.0
1.5
mV
mV
mV
mV
V
Change with Current
2, 3
1
-10.0 10.0
-20.0 20.0
2, 3
1
VF
TC
Forward Bias Voltage
IF = 2mA
-1.0
-0.4
50
Temperature Coefficient
(Note 4)
PPM/˚C
2, 3
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed
specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test
conditions.
Note 2: The maximum power dissipation must be derated at elevated temperatures and is dictated by T
(maximum junction temperature), θ (package junction
JA
Jmax
to ambient thermal resistance), and T (ambient temperature). The maximum allowable power dissipation at any temperature is P
= (T
- T )/θ or the
A
Dmax
Jmax A JA
number given in the Absolute Maximum Ratings, whichever is lower.
Note 3: Human body model, 1.5KΩ in series with 100pF.
Note 4: The average temperature coefficient is defined as the maximum deviation of reference voltage, at all measured temperatures between the operating T
Min
& T , divided by (T
Max
− T ). The measured temperatures (T
Min
) are −55˚C, 25˚C, & 125˚C or ∆V
Measured
/ (T
− T
Min
)
Max
Ref
Max
www.national.com
4
Typical Performance Characteristics
Reverse Characteristics
Reverse Characteristics
20156113
20156114
Temperature Drift of 3
Representative Units
Forward Characteristics
20156116
20156115
Reverse Dynamic Impedance
Reverse Dynamic Impedance
20156118
20156117
5
www.national.com
Typical Performance Characteristics (Continued)
Noise Voltage
Filtered Output Noise
20156120
20156119
Response Time
20156121
Typical Applications
Reference from
1.5V Battery
Wide Input
Range Reference
20156123
20156108
Micropower Reference
from 9V Battery
20156122
www.national.com
6
Typical Applications (Continued)
Precision 1µA to 1mA Current Sources
Micropower* 5V Regulator
20156126
20156124
*I . 30µA
Q
Micropower* 10V Reference
20156127
20156125
*I .20µA standby current
Q
7
www.national.com
Typical Applications (Continued)
METER THERMOMETERS
Centigrade Thermometer
0˚C−100˚C Thermometer
20156101
20156128
Calibration
Calibration
1. Adjust R1 so that V1 = temp at 1mV/˚K
2. Adjust V2 to 273.2mV
1. Short LM385-1.2, adjust R3 for I
= temp at 1µA/˚K
OUT
2. Remove short, adjust R2 for correct reading in centigrade
†
I
for 1.3V to 1.6V battery volt-
Q
†
I
at 1.3V.500µA
Q
age = 50µA to 150µA
I
Q
at 1.6V.2.4mA
Micropower Thermocouple Cold Junction
Compensator
Lower Power Thermometer
20156129
*2N3638 or 2N2907 select for inverse H . 5
FE
†
Select for operation at 1.3V
. 600µA to 900µA
‡
I
Q
0˚F−50˚F Thermometer
20156131
Adjustment Procedure
1. Adjust TC ADJ pot until voltage across R1 equals Kelvin temperature
multiplied by the thermocouple Seebeck coefficient.
2. Adjust zero ADJ pot until voltage across R2 equals the thermocouple
Seebeck coefficient multiplied by 273.2.
Thermocouple Seebeck R1 R2 Voltage
Voltage
Across
R2
Type
Coefficient (Ω) (Ω) Across
R1
@
(µV/˚C)
25˚C
(mV)
(mV)
15.60
12.77
12.17
1.908
20156130
J
T
K
S
52.3
42.8
40.8
6.4
5231.24k
432 1k
412953Ω
63.4150Ω
14.32
11.78
11.17
1.766
Calibration
1. Short LM385-1.2, adjust R3 for I
= temp at 1.8µA/˚K
OUT
2. Remove short, adjust R2 for correct reading in ˚F
Typical supply current 50µA
www.national.com
8
Revision History Section
Released
Revision
Section
Originator
Changes
10/07/05
A
New Release, Corporate format
L. Lytle
2 MDS data sheets converted into one Corp.
data sheet format. MNLM185-1.2-X Rev 2A3
and MNLM185BY-1.2-X Rev 0B0 data
sheets will be archived.
9
www.national.com
Physical Dimensions inches (millimeters) unless otherwise noted
TO-46 Metal Can Package (H)
NS Package Number H02A
Leadless Chip Carrier Package (E)
NS Package Number E20A
www.national.com
10
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
Ceramic SOIC Package (WG)
NS Package Number WG10A
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves
the right at any time without notice to change said circuitry and specifications.
For the most current product information visit us at www.national.com.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS
WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR
CORPORATION. As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body, or
(b) support or sustain life, and whose failure to perform when
properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to result
in a significant injury to the user.
2. A critical component is any component of a life support
device or system whose failure to perform can be reasonably
expected to cause the failure of the life support device or
system, or to affect its safety or effectiveness.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products
Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain
no ‘‘Banned Substances’’ as defined in CSP-9-111S2.
Leadfree products are RoHS compliant.
National Semiconductor
Americas Customer
Support Center
National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
National Semiconductor
Asia Pacific Customer
Support Center
National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: new.feedback@nsc.com
Tel: 1-800-272-9959
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
Email: ap.support@nsc.com
Email: jpn.feedback@nsc.com
Tel: 81-3-5639-7560
www.national.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Audio
Applications
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
www.ti.com/industrial
www.ti.com/medical
www.ti.com/security
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
Medical
Security
Logic
Space, Avionics and Defense www.ti.com/space-avionics-defense
Transportation and Automotive www.ti.com/automotive
Power Mgmt
Microcontrollers
RFID
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
Video and Imaging
www.ti.com/video
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated
相关型号:
LM185H-1.2-MLS
1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.235V, MBCY2, HERMETIC SEALED, METAL CAN, TO-46, 2 PIN
NSC
LM185H-1.2-SMD
IC 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.235 V, MBCY2, METAL CAN, TO-46, 2 PIN, Voltage Reference
NSC
©2020 ICPDF网 联系我们和版权申明