LM26001MXA/NOPB
更新时间：2024-09-18 22:02:05
品牌：TI
描述：LM26001/-Q1 1.5-A Switching Regulator With High-Efficiency Sleep Mode
概述
规格参数
数据手册
替代型号LM26001MXA/NOPB 概述
LM26001/-Q1 1.5-A Switching Regulator With High-Efficiency Sleep Mode 稳压芯片 开关式稳压器或控制器
LM26001MXA/NOPB 规格参数
| 是否无铅： | 不含铅 | 是否Rohs认证： | 符合 |
| 生命周期： | Active | 包装说明： | HTSSOP-16 |
| Reach Compliance Code： | compliant | ECCN代码： | EAR99 |
| HTS代码： | 8542.39.00.01 | Factory Lead Time： | 1 week |
| 风险等级： | 0.65 | Is Samacsys： | N |
| 其他特性： | SEATED HGT-NOM | 模拟集成电路 - 其他类型： | SWITCHING REGULATOR |
| 控制模式： | CURRENT-MODE | 控制技术： | PULSE WIDTH MODULATION |
| 最大输入电压： | 38 V | 最小输入电压： | 4 V |
| 标称输入电压： | 12 V | JESD-30 代码： | R-PDSO-G16 |
| JESD-609代码： | e3 | 长度： | 5 mm |
| 湿度敏感等级： | 1 | 功能数量： | 1 |
| 端子数量： | 16 | 最高工作温度： | 125 °C |
| 最低工作温度： | -40 °C | 最大输出电流： | 3.2 A |
| 最大输出电压： | 35 V | 最小输出电压： | 1.25 V |
| 封装主体材料： | PLASTIC/EPOXY | 封装代码： | HTSSOP |
| 封装等效代码： | TSSOP16,.25 | 封装形状： | RECTANGULAR |
| 封装形式： | SMALL OUTLINE, HEAT SINK/SLUG, THIN PROFILE, SHRINK PITCH | 峰值回流温度（摄氏度）： | 260 |
| 认证状态： | Not Qualified | 座面最大高度： | 1.1 mm |
| 子类别： | Switching Regulator or Controllers | 标称供电电压 (Vsup)： | 12 V |
| 表面贴装： | YES | 切换器配置： | BUCK |
| 最大切换频率： | 500 kHz | 温度等级： | AUTOMOTIVE |
| 端子面层： | Matte Tin (Sn) | 端子形式： | GULL WING |
| 端子节距： | 0.65 mm | 端子位置： | DUAL |
| 处于峰值回流温度下的最长时间： | NOT SPECIFIED | 宽度： | 4.4 mm |
| Base Number Matches： | 1 |
LM26001MXA/NOPB 数据手册
通过下载LM26001MXA/NOPB数据手册来全面了解它。这个PDF文档包含了所有必要的细节，如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载Sample &
Buy
Support &
Community
Product
Folder
Tools &
Software
Technical
Documents
LM26001, LM26001-Q1
SNVS430I –MAY 2006–REVISED MARCH 2015
LM26001/-Q1 1.5-A Switching Regulator With High-Efficiency Sleep Mode
1 Features
3 Description
The LM26001 is a switching regulator designed for
the high-efficiency requirements of applications with
standby modes. The device features a low-current
sleep mode to maintain efficiency under light-load
conditions and current-mode control for accurate
regulation over a wide input voltage range. Quiescent
current is reduced to 10 µA typically in shutdown
mode and less than 40 µA in sleep mode. Forced
PWM mode is also available to disable sleep mode.
1
•
LM26001-Q1 is an Automotive-Grade Product that
is AEC-Q100 Grade 1 Qualified (–40°C to +125°C
Operating Junction Temperature)
•
•
•
•
•
•
•
•
•
•
•
•
•
•
High-Efficiency Sleep Mode
40-µA Typical Iq in Sleep Mode
10-µA Typical Iq in Shutdown Mode
3.0-V Minimum Input Voltage
4.0-V to 38-V Continuous Input Range
1.5% Reference Accuracy
The LM26001 can deliver up to 1.5 A of continuous
load current with a fixed current limit, through the
internal N-channel switch. The part has a wide input
voltage range of 4.0 V to 38 V and can operate with
input voltages as low as 3 V during line transients.
Cycle-by-Cycle Current Limit
Adjustable Frequency (150 kHz to 500 kHz)
Synchronizable to an External Clock
Power Good Flag
Operating frequency is adjustable from 150 kHz to
500 kHz with
a single resistor and can be
Forced PWM Function
synchronized to an external clock.
Adjustable Soft-Start
Other features include Power Good, adjustable soft-
start, enable pin, input undervoltage protection, and
an internal bootstrap diode for reduced component
count.
HTSSOP-16 Exposed Pad Package
Thermal Shut Down
2 Applications
Device Information(1)
•
•
•
•
•
Automotive Telematics
Navigation Systems
PART NUMBER
LM26001
PACKAGE
BODY SIZE (NOM)
HTSSOP (16)
5.00 mm x 4.40 mm
In-Dash Instrumentation
Battery-Powered Applications
LM26001-Q1
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
Standby Power for Home Gateways/Set-top
Boxes
Typical Application Circuit
VIN
1
2
12
VIN
VIN
VBIAS
VOUT
C6
16
15
SW
C1
L
3
4
PGOOD
EN
+
SW
C4
D1
R1
14
7
R4
BOOT
EN
LM26001
11
SYNC
SS
FB
VDD
5
9
6
13
8
COMP
SYNC
FREQ
FPWM
VDD
GND
C8
R2
C5
10
R6
EP
17
C3
R3
R5
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM26001, LM26001-Q1
SNVS430I –MAY 2006–REVISED MARCH 2015
www.ti.com
Table of Contents
7.4 Device Functional Modes........................................ 16
Applications and Implementation ...................... 17
8.1 Application Information............................................ 17
8.2 Typical Application .................................................. 17
Power Supply Recommendations...................... 23
1
2
3
4
5
6
Features.................................................................. 1
Applications ........................................................... 1
Description ............................................................. 1
Revision History..................................................... 2
Pin Configuration and Functions......................... 3
Specifications......................................................... 4
6.1 Absolute Maximum Ratings ...................................... 4
6.2 ESD Ratings - LM26001 ........................................... 4
6.3 ESD Ratings - LM26001-Q1 ..................................... 4
6.4 Recommended Operating Conditions....................... 5
6.5 Thermal Information.................................................. 5
6.6 Electrical Characteristics........................................... 5
6.7 Typical Characteristics.............................................. 8
Detailed Description ............................................ 11
7.1 Overview ................................................................. 11
7.2 Functional Block Diagram ....................................... 11
7.3 Feature Description................................................. 12
8
9
10 Layout................................................................... 23
10.1 Layout Guidelines ................................................. 23
10.2 Layout Example .................................................... 24
10.3 Thermal Considerations and TSD......................... 24
11 Device and Documentation Support ................. 25
11.1 Documentation Support ........................................ 25
11.2 Related Links ........................................................ 25
11.3 Trademarks........................................................... 25
11.4 Electrostatic Discharge Caution............................ 25
11.5 Glossary................................................................ 25
7
12 Mechanical, Packaging, and Orderable
Information ........................................................... 25
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision H (November 2014) to Revision I
Page
•
•
Update made to the Power Dissipation description in Section 6.1 ....................................................................................... 4
Changed ESD Ratings to ± and moved storage temp to Absolute Maximum Ratings .......................................................... 4
Changes from Revision G (April 2013) to Revision H
Page
•
Added Pin Configuration and Functions section, Handling Rating table, Feature Description section, Device
Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout
section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information
section ................................................................................................................................................................................... 1
Changes from Revision F (April 2013) to Revision G
Page
•
Changed layout of National Data Sheet to TI format ........................................................................................................... 24
2
Submit Documentation Feedback
Copyright © 2006–2015, Texas Instruments Incorporated
Product Folder Links: LM26001 LM26001-Q1
LM26001, LM26001-Q1
www.ti.com
SNVS430I –MAY 2006–REVISED MARCH 2015
5 Pin Configuration and Functions
16-Pin
HTSSOP Package
Top View
VIN
VIN
1
2
3
4
5
6
7
16 SW
15 SW
PGOOD
EN
14 BOOT
13 VDD
12 VBIAS
11 SYNC
10 FPWM
SS
COMP
FB
GND
8
9 FREQ
Exposed Pad
Connect to GND
Pin Functions
PIN
NAME
I/O
DESCRIPTION
NO.
1
VIN
VIN
A
A
O
Power supply input
Power supply input
2
3
PGOOD
Power Good pin. An open-drain output which goes high when the output voltage is greater than
92% of nominal.
4
5
EN
SS
I
Enable is an analog level input pin. When pulled below 0.8 V, the device enters shutdown mode.
Soft-start pin. Connect a capacitor from this pin to GND to set the soft-start time.
Compensation pin. Connect to a resistor capacitor pair to compensate the control loop.
Feedback pin. Connect to a resistor divider between Vout and GND to set output voltage.
Ground
A
A
A
G
A
I
6
COMP
FB
7
8
GND
FREQ
FPWM
9
Frequency adjust pin. Connect a resistor from this pin to GND to set the operating frequency.
10
FPWM is a logic level input pin. For normal operation, connect to GND. When pulled high, sleep
mode operation is disabled.
11
12
SYNC
VBIAS
I
Frequency synchronization pin. Connect to an external clock signal for synchronized operation.
SYNC must be pulled low for non-synchronized operation.
A
Connect to an external 3-V or greater supply to bypass the internal regulator for improved efficiency.
If not used, VBIAS should be tied to GND.
13
14
VDD
A
A
The output of the internal regulator. Bypass with a minimum 1.0-µF capacitor.
BOOT
Bootstrap capacitor pin. Connect a 0.1-µF minimum ceramic capacitor from this pin to SW to
generate the gate drive bootstrap voltage.
15
16
EP
SW
SW
EP
A
A
G
Switch pin. The source of the internal N-channel switch.
Switch pin. The source of the internal N-channel switch.
Exposed Pad thermal connection. Connect to GND.
Copyright © 2006–2015, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LM26001 LM26001-Q1
LM26001, LM26001-Q1
SNVS430I –MAY 2006–REVISED MARCH 2015
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings(1)(2)
MIN
–0.3
–0.5
–0.3
–0.3
–0.3
SW-0.3
–0.3
–0.3
–0.3
–0.3
–0.3
–0.3
MAX
40
40
7
UNIT
V
VIN
SW(3)
VDD
VBIAS
FB
V
V
10
6
V
V
Voltages
from the
indicated
pins to
GND
BOOT
SW+7
7
V
PGOOD
V
FREQ
7
V
SYNC
7
V
EN
40
y7
V
FPWM
V
SS
7
V
Power Dissipation(4)(5)
2.6
215
220
W
°C
°C
Recomme Vapor Phase (70s)
nded Lead
Infrared (15s)
Temperatu
re
Storage
temperatur
e
Tstg
–65
150
°C
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Recommended Operating Conditions indicate
conditions for which the device is intended to be functional, but do not ensure specific performance limits. For ensured specifications
and test conditions, see the Electrical Characteristics.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
(3) The absolute maximum specification applies to DC voltage. An extended negative voltage limit of -2V applies for a pulse of up to 1 µs,
and –1 V for a pulse of up to 20 µs.
(4) The maximum allowable power dissipation is a function of the maximum junction temperature, TJ_MAX, the junction-to-ambient thermal
resistance, θJA, and the ambient temperature, TA. The maximum allowable power dissipation at any ambient temperature is calculated
using: PD_MAX = (TJ_MAX - TA) /θJA. The maximum power dissipation of 2.6W is determined using TA = 25°C, θJA = 38°C/W, and
TJ_MAX = 125°C. The number stated here reflects the maximum power dissipation for the package and not the device.
(5) For Device Power Dissipation, please refer to section 10.3.
6.2 ESD Ratings - LM26001
VALUE
± 2
UNIT
kV
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins(1)
Charged device model (CDM), per JEDEC specification JESD22-C101,
all pins(2)
± 1
V(ESD)
Electrostatic discharge
Machine model
± 200
V
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 ESD Ratings - LM26001-Q1
VALUE
UNIT
kV
Human body model (HBM), per AEC Q100-002(1)
± 2
± 1
Corner pins (1, 8, 9, and
16)
Charged device model (CDM), per AEC
Q100-011
V(ESD)
Electrostatic discharge
Other pins
± 1
Machine model
± 200
V
(1) AEC Q100-002 indicates HBM stressing is done in accordance with the ANSI/ESDA/JEDEC JS-001 specification.
4
Submit Documentation Feedback
Copyright © 2006–2015, Texas Instruments Incorporated
Product Folder Links: LM26001 LM26001-Q1
LM26001, LM26001-Q1
www.ti.com
SNVS430I –MAY 2006–REVISED MARCH 2015
6.4 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
–40
3.0
MAX UNIT
Operating Junction Temp.
Supply Voltage(1)
125
38
°C
V
(1) Below 4.0-V input, power dissipation may increase due to increased RDS(ON). Therefore, a minimum input voltage of 4.0 V is required to
operate continuously within specification. A minimum of 3.9 V (typical) is also required for startup.
6.5 Thermal Information
LM26001
THERMAL METRIC(1)
PWP
16 PINS
38.8
UNIT
RθJA
Junction-to-ambient thermal resistance
RθJC(top)
RθJB
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
23.0
16.7
°C/W
ψJT
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
0.6
ψJB
16.4
RθJC(bot)
1.7
(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
6.6 Electrical Characteristics
Unless otherwise stated, Vin=12 V. Minimum and Maximum limits are ensured through test, design, or statistical correlation.
Typical values represent the most likely parametric norm at TJ = 25°C, and are provided for reference purposes only.(1)
PARAMETER
TEST CONDITIONS
MIN
TYP
10.8
38
MAX UNIT
SYSTEM
(2)
ISD
Shutdown Current
EN = 0 V
µA
EN = 0 V, –40°C ≤ TJ ≤ 125°C
20
µA
70
(2)
Iq_Sleep_VB
Quiescent Current
Quiescent Current
Sleep mode, VBIAS = 5 V
Sleep mode, VBIAS = 5 V, –40°C
≤ TJ ≤ 125°C
Iq_Sleep_VDD
Sleep mode, VBIAS = GND
75
µA
Sleep mode, VBIAS = GND,
125
–40°C ≤ TJ ≤ 125°C
Iq_PWM_VB
Quiescent Current
Quiescent Current
Bias Current
PWM mode, VBIAS = 5 V
PWM mode, VBIAS = GND
Sleep mode, VBIAS = 5 V
150
0.65
33
230
µA
mA
µA
Iq_PWM_VDD
0.85
(2)
IBIAS_Sleep
Sleep mode, VBIAS = 5 V, –40°C
85
≤ TJ ≤ 125°C
IBIAS_PWM
VFB
Bias Current
PWM mode, VBIAS = 5 V
5 V < Vin < 38 V
0.5
0.70
mA
V
Feedback Voltage
1.234
5 V < Vin < 38 V, –40°C ≤ TJ ≤
125°C
1.2155
1.2525
±200
IFB
FB Bias Current
nA
ΔVOUT/ΔVIN
ΔVOUT/ΔIOUT
VDD
Vout line regulation
Vout load regulation
VDD output voltage
5 V < Vin < 38 V
0.001
0.07%
5.95
%/V
0.8 V < VCOMP < 1.15 V
7 V < Vin < 35 V, IVDD= 0 mA to 5
mA
V
7 V < Vin < 35 V, IVDD= 0 mA to 5
5.50
6.50
mA, –40°C ≤ TJ ≤ 125°C
(1) All room temperature limits are 100% production tested. All limits at temperature extremes are ensured through correlation using
standard Statistical Quality Control (SQC) methods. All limits are used to calculate Average Outgoing Quality Level (AOQL).
(2) Iq and ISD specify the current into the VIN pin. IBIAS is the current into the VBIAS pin when the VBIAS voltage is greater than 3 V. All
quiescent current specifications apply to non-switching operation.
Copyright © 2006–2015, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: LM26001 LM26001-Q1
LM26001, LM26001-Q1
SNVS430I –MAY 2006–REVISED MARCH 2015
www.ti.com
Electrical Characteristics (continued)
Unless otherwise stated, Vin=12 V. Minimum and Maximum limits are ensured through test, design, or statistical correlation.
Typical values represent the most likely parametric norm at TJ = 25°C, and are provided for reference purposes only.(1)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
ISS_Source
Soft-start source current
2.2
µA
–40°C ≤ TJ ≤ 125°C
1.5
4.6
Vbias_th
VBIAS On Voltage
Specified at IBIAS = 92.5% of full
value
2.64
2.9
3.07
V
SWITCHING
RDS(ON)
Switch on Resistance
Isw = 1A
0.2
Ω
Isw = 1A, –40°C ≤ TJ ≤ 125°C
Vin = 38 V, VSW = 0 V
0.12
0.42
Isw_off
Switch off state leakage current
0.002
µA
Vin = 38 V, VSW = 0 V, –40°C ≤
TJ ≤ 125°C
5.0
fsw
Switching Frequency
FREQ voltage
RFREQ = 62k, 124k, 240k
±10%
VFREQ
fSW range
VSYNC
1.0
1.2
1.1
V
kHz
V
Switching Frequency range
Sync pin threshold
–40°C ≤ TJ ≤ 125°C
150
0.8
500
1.6
SYNC rising
SYNC rising, –40°C ≤ TJ ≤ 125°C
SYNC falling
SYNC falling, –40°C ≤ TJ ≤ 125°C
Sync pin hysteresis
114
6
mV
nA
ISYNC
SYNC leakage current
FSYNC_UP
Upper frequency synchronization range As compared to nominal fSW
,
30%
–40°C ≤ TJ ≤ 125°C
FSYNC_DN
Lower frequency synchronization range As compared to nominal fSW
,
–20%
–40°C ≤ TJ ≤ 125°C
TOFFMIN
Minimum Off-time
Minimum On-time
365
155
ns
ns
TONMIN
THSLEEP_HYS
THWAKE
Sleep mode threshold hysteresis
Wake up threshold
VFB rising, % of THWAKE
101.2%
1.234
Measured at falling FB, COMP =
0.6 V
V
IBOOT
BOOT pin leakage current
BOOT = 16 V, SW = 10 V
0.0006
µA
BOOT = 16 V, SW = 10 V, –40°C
≤ TJ ≤ 125°C
5.0
3.2
PROTECTION
ILIMPK
Peak Current Limit
2.5
A
–40°C ≤ TJ ≤ 125°C
1.85
VFB_SC
Short circuit frequency foldback
threshold
Measured at FB falling
0.87
V
F_min_sc
Min Frequency in foldback
Power Good Threshold
VFB < 0.3 V
71
kHz
VTH_PGOOD
Measured at FB, PGOOD rising
92%
Measured at FB, PGOOD rising,
–40°C ≤ TJ ≤ 125°C
89%
2%
95%
8%
PGOOD hysteresis
7%
0.2
64
IPGOOD_HI
PGOOD leakage current
PGOOD on resistance
PGOOD = 5 V
nA
RDS_PGOOD
PGOOD sink current = 500 µA
Ω
6
Submit Documentation Feedback
Copyright © 2006–2015, Texas Instruments Incorporated
Product Folder Links: LM26001 LM26001-Q1
LM26001, LM26001-Q1
www.ti.com
SNVS430I –MAY 2006–REVISED MARCH 2015
Electrical Characteristics (continued)
Unless otherwise stated, Vin=12 V. Minimum and Maximum limits are ensured through test, design, or statistical correlation.
Typical values represent the most likely parametric norm at TJ = 25°C, and are provided for reference purposes only.(1)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
VUVLO
Under-voltage Lock-Out Threshold
Vin falling , shutdown, VDD = VIN
2.9
V
Vin falling , shutdown, VDD = VIN,
2.60
3.20
–40°C ≤ TJ ≤ 125°C
Vin rising, soft-start, VDD = VIN
3.9
Vin rising, soft-start, VDD = VIN,
3.60
4.20
–40°C ≤ TJ ≤ 125°C
TSD
Thermal Shutdown Threshold
Thermal resistance
160
38
°C
θJA
Power dissipation = 1W, 0 lfpm air
flow
°C/W
LOGIC
VthEN
Enable Threshold voltage
1.2
V
–40°C ≤ TJ ≤ 125°C
0.8
0.8
1.4
mV
µA
V
Enable hysteresis
EN source current
FPWM threshold
120
4.5
1.2
IEN_Source
VTH_FPWM
EN = 0 V
–40°C ≤ TJ ≤ 125°C
1.6
nA
IFPWM
EA
FPWM leakage current
FPWM = 5 V
35
gm
Error amp trans-conductance
670
µmho
–40°C ≤ TJ ≤ 125°C
VCOMP = 0.9 V
VCOMP = 0.9 V
400
1000
µA
ICOMP
COMP source current
COMP sink current
56
56
µA
VCOMP
COMP pin voltage range
0.64
1.27
V
Copyright © 2006–2015, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: LM26001 LM26001-Q1
LM26001, LM26001-Q1
SNVS430I –MAY 2006–REVISED MARCH 2015
www.ti.com
6.7 Typical Characteristics
Unless otherwise specified the following conditions apply: VIN = 12 V, TJ = 25°C.
1.236
1.234
1.236
1.235
1.234
1.233
1.232
1.232
1.230
1.228
-20
-40
0
20
TEMPERATURE (ºC)
0
5
10 15 20
(V)
30 35 40
40 60
120 140
80 100
25
V
IN
Figure 1. VFB vs Temperature
Figure 2. VFB vs Vin (IDC = 300 mA)
90
80
70
60
50
700
600
500
IQ
IQ
(VBIAS=0V)
(VBIAS=0V)
IVBIAS
(VBIAS=5V)
400
300
IVBIAS
(VBIAS=5V)
40
30
20
IQ
IQ
200
100
(VBIAS=5V)
(VBIAS=5V)
140
-40
100
120
-20
0
20 40 60 80
-40
100
120 140
-20
0
20 40 60 80
TEMPERATURE (ºC)
TEMPERATURE (ºC)
Figure 4. IQ and IVBIAS vs Temperature (PWM Mode)
Figure 3. IQ and IVBIAS vs Temperature (Sleep Mode)
102
4.1
3.9
On Threshold
3.7
101
3.5
3.3
100
99
3.1
Off Threshold
2.9
2.7
2.5
98
-40
-20
0
20
TEMPERATURE (ºC)
40 60
120 140
80 100
-40 -20
0
20 40 60 80 100 120 140
TEMPERATURE (ºC)
Figure 5. Normalized Switching Frequency vs Temperature
(300 kHz)
Figure 6. UVLO Threshold vs Temperature (VDD = VIN)
8
Submit Documentation Feedback
Copyright © 2006–2015, Texas Instruments Incorporated
Product Folder Links: LM26001 LM26001-Q1
LM26001, LM26001-Q1
www.ti.com
SNVS430I –MAY 2006–REVISED MARCH 2015
Typical Characteristics (continued)
Unless otherwise specified the following conditions apply: VIN = 12 V, TJ = 25°C.
350
3.0
2.8
2.6
2.4
2.2
2.0
300
250
200
150
100
50
0
-40 -20
0
20 40 60 80 100 120 140
TEMPERATURE (ºC)
0.2
0.4
0.6
0.8
(V)
1.0
1.2
V
FB
Figure 7. Peak Current Limit vs Temperature
Figure 8. Short Circuit Foldback Frequency vs VFB (325 kHz
Nominal)
100
100
5Vout
5Vout
90
90
3.3Vout
3.3Vout
80
80
70
70
FPWM
mode
60
FPWM
mode
60
50
50
1
10
100
(mA)
1000
10000
1
10
100
(mA)
1000
10000
I
I
DC
DC
Figure 9. Efficiency vs Load Current (330 kHz)
Figure 10. Efficiency vs Load Current (500 kHz)
Vout
Vout
1V/Div
40 mV/Div
PGOOD
5V/Div
Iout
500 mA/Div
SS
1V/Div
EN
10V/Div
1 Ps/DIV
200 Ps/DIV
Figure 11. Startup Waveforms
Figure 12. Load Transient Response
Copyright © 2006–2015, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: LM26001 LM26001-Q1
LM26001, LM26001-Q1
SNVS430I –MAY 2006–REVISED MARCH 2015
www.ti.com
Typical Characteristics (continued)
Unless otherwise specified the following conditions apply: VIN = 12 V, TJ = 25°C.
500
1A 125°C
450
400
1A 25°C
350
300
1A -40°C
250
200
150
40mA -40°C
100
40mA
25 to 125°C
50
0
3
3.5
4
4.5
VIN (V)
Figure 13. Low Input Voltage Dropout Nominal VOUT = 5 V
5
5.5
10
Submit Documentation Feedback
Copyright © 2006–2015, Texas Instruments Incorporated
Product Folder Links: LM26001 LM26001-Q1
LM26001, LM26001-Q1
www.ti.com
SNVS430I –MAY 2006–REVISED MARCH 2015
7 Detailed Description
7.1 Overview
The LM26001 is a current mode PWM buck regulator. At the beginning of each clock cycle, the internal high-side
switch turns on, allowing current to ramp up in the inductor. The inductor current is internally monitored during
each switching cycle. A control signal derived from the inductor current is compared to the voltage control signal
at the COMP pin, derived from the feedback voltage. When the inductor current reaches the threshold, the high-
side switch is turned off and inductor current ramps down. While the switch is off, inductor current is supplied
through the catch diode. This cycle repeats at the next clock cycle. In this way, duty cycle and output voltage are
controlled by regulating inductor current. Current mode control provides superior line and load regulation. Other
benefits include cycle by cycle current limiting and a simplified compensation scheme. Typical PWM waveforms
are shown in Figure 14.
Vout
10 mV/Div
IL
500 mA/Div
ID
1A/Div
V
SW
5V/Div
1 Ps/DIV
Figure 14. PWM Waveforms 1-A Load, Vin = 12 V
7.2 Functional Block Diagram
VIN
5 PA
BG
IREF
TSD
on
LDO
UVLO
VDD
SD
qn
VDD_low
EN
Switchover
control
fpwm
VBIAS
FPWM
LG
wake
BG
+
-
VREG
Sync and
bootstrap
control
Sleep
Set
Sleep
Reset
fpwm
sleep
+
0.6V
+
-
FPWM / Sleep
Peak Current
Control
BOOT
VIN
EA
-
+
FB
-
+
V clamp
BG
I Sense
blanking
COMP
frequency
foldback
Corrective
Ramp
-
+
ff
qn
0.9V
+
-
PWM Control
Logic
-
+
PWM
Comp
0.92BG
SW
SW
PG
sleep
PGOOD
Clock / Sync
LG
-
+
ss end
2 PA
-
ff
+
FREQ
SYNC
SS
VDD_low
TSD
on
SS
logic
+
-
soft start
SD
EP
GND
Copyright © 2006–2015, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: LM26001 LM26001-Q1
LM26001, LM26001-Q1
SNVS430I –MAY 2006–REVISED MARCH 2015
www.ti.com
7.3 Feature Description
7.3.1 Sleep Mode
In light load conditions, the LM26001 automatically switches into sleep mode for improved efficiency. As loading
decreases, the voltage at FB increases and the COMP voltage decreases. When the COMP voltage reaches the
0.6-V (typical) clamp threshold, and the FB voltage rises 1% above nominal, sleep mode is enabled and
switching stops. The regulator remains in sleep mode until the FB voltage falls to the reset threshold, at which
point switching resumes. This 1% FB window limits the corresponding output ripple to approximately 1% of
nominal output voltage. The sleep cycle will repeat until load current is increased. Figure 15 shows typical
switching and output voltage waveforms in sleep mode.
Vout
50 mV/Div
IL
200 mA/Div
V
SW
5V/Div
100 Ps/DIV
Figure 15. Sleep Mode Waveforms 25-mA Load, Vin = 12 V
In sleep mode, quiescent current is reduced to less than 40 µA when not switching. The DC sleep mode
threshold can be calculated according to the equation below:
2
Vin - Vout
L
fsw x L
ISleep
=
Imin + 0.13 P
x
D x 2 x (Vin ± Vout)
(1)
Where Imin = Ilim/16 (2.5A/16 typically) and D = duty cycle, defined as (Vout + Vdiode)/Vin.
When load current increases above this limit, the LM26001 is forced back into normal PWM operation. The sleep
mode threshold varies with frequency, inductance, and duty cycle as shown in Figure 16.
250
200
150
500 kHz
100
50
0
330 kHz
22 PH
15PH
22PH
15PH
0
10
20
(V)
30
40
V
IN
Figure 16. Sleep Mode Threshold vs Vin Vout = 3.3 V
Below the sleep threshold, decreasing load current results in longer sleep cycles, which can be quantified as
shown below:
Dwake = Iload/Isleep
(2)
Where Dwake is the percentage of time awake when the load current is below the sleep threshold.
Sleep mode combined with low IQ operation minimizes the input supply current. Input supply current in sleep
mode can be calculated based on the wake duty cycle, as shown below:
12
Submit Documentation Feedback
Copyright © 2006–2015, Texas Instruments Incorporated
Product Folder Links: LM26001 LM26001-Q1
LM26001, LM26001-Q1
www.ti.com
SNVS430I –MAY 2006–REVISED MARCH 2015
Feature Description (continued)
Iin = Iq + (IQG x Dwake) + (Io x D)
(3)
Where IQG is the gate drive current, calculated as:
IQG = (4.6 x 10-9) x fSW
And Io is the sum of Iload, Ibias, and current through the feedback resistors.
Because this calculation applies only to sleep mode, use the Iq_Sleep_VB and IBIAS_SLEEP values from the Electrical
Characteristics. If VBIAS is connected to ground, use the same equation with Ibias equal to zero and Iq_Sleep_VDD
.
7.3.2 FPWM
Pulling the FPWM pin high disables sleep mode and forces the LM26001 to always operate in PWM mode. Light
load efficiency is reduced in PWM mode, but switching frequency remains stable. The FPWM pin can be
connected to the VDD pin to pull it high. In FPWM mode, under light load conditions, the regulator operates in
discontinuous conduction mode (DCM) . In discontinuous conduction mode, current through the inductor starts at
zero and ramps up to its peak, then ramps down to zero again. Until the next cycle, the inductor current remains
at zero. At nominal load currents, in FPWM mode, the device operates in continuous conduction mode, where
positive current always flows in the inductor. Typical discontinuous operation waveforms are shown in Figure 17.
Vout
10 mV/Div
IL
200 mA/Div
V
SW
5V/Div
1 Ps/DIV
Figure 17. Discontinuous Mode Waveforms 75-mA Load, Vin = 12 V
At very light load, in FPWM mode, the LM26001 may enter sleep mode. This is to prevent an over-voltage
condition from occurring. However, the FPWM sleep threshold is much lower than in normal operation.
7.3.3 Enable
The LM26001 provides a shutdown function via the EN pin to disable the device when the output voltage does
not need to be maintained. EN is an analog level input with typically 120 mV of hysteresis. The device is active
when the EN pin is above 1.2 V (typical) and in shutdown mode when EN is below this threshold. When EN goes
high, the internal VDD regulator turns on and charges the VDD capacitor. When VDD reaches 3.9 V (typical), the
soft-start pin begins to source current. In shutdown mode, the VDD regulator shuts down and total quiescent
current is reduced to 10 µA (typical). Because the EN pin sources 4.5 µA (typical) of pull-up current, this pin can
be left open for always-on operation. When open, EN will be pulled up to VIN.
If EN is connected to VIN, it must be connected through a 10 kΩ resistor to limit noise spikes. EN can also be
driven externally with a maximum voltage of 38V or VIN + 15V, whichever is lower.
7.3.4 Soft-Start
The soft-start feature provides a controlled output voltage ramp up at startup. This reduces inrush current and
eliminates output overshoot at turn-on. The soft-start pin, SS, must be connected to GND through a capacitor. At
power-on, enable, or UVLO recovery, an internal 2.2 µA (typical) current charges the soft-start capacitor. During
soft-start, the error amplifier output voltage is controlled by both the soft-start voltage and the feedback loop. As
the SS pin voltage ramps up, the duty cycle increases proportional to the soft-start ramp, causing the output
voltage to ramp up. The rate at which the duty cycle increases depends on the capacitance of the soft-start
capacitor. The higher the capacitance, the slower the output voltage ramps up. The soft-start capacitor value can
be calculated with the following equation:
Copyright © 2006–2015, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: LM26001 LM26001-Q1
LM26001, LM26001-Q1
SNVS430I –MAY 2006–REVISED MARCH 2015
www.ti.com
Feature Description (continued)
Iss x tss
Css =
1.234V
(4)
Where tss is the desired soft-start time and Iss is the soft-start source current. During soft-start, current limit and
synchronization remain in effect, while sleep mode and frequency foldback are disabled. Soft-start mode ends
when the SS pin voltage reaches 1.23 V typical. At this point, output voltage control is transferred to the FB pin
and the SS pin is discharged.
7.3.5 Current Limit
The peak current limit is set internally by directly measuring peak inductor current through the internal switch. To
ensure accurate current sensing, VIN should be bypassed with a minimum 1-µF ceramic capacitor placed directly
at the pin.
When the inductor current reaches the current limit threshold, the internal FET turns off immediately allowing
inductor current to ramp down until the next cycle. This reduction in duty cycle corresponds to a reduction in
output voltage.
The current limit comparator is disabled for less than 100 ns at the leading edge for increased immunity to
switching noise.
Because the current limit monitors peak inductor current, the DC load current limit threshold varies with
inductance and frequency. Assuming a minimum current limit of 1.85A, maximum load current can be calculated
as follows:
Iripple
Iloadmax = 1.85A -
2
(5)
Where Iripple is the peak-to-peak inductor ripple current, calculated as shown below:
(Vin ± Vout) x Vout
Iripple =
fsw x L x Vin
(6)
To find the worst case (lowest) current limit threshold, use the maximum input voltage and minimum current limit
specification.
During high over-current conditions, such as output short circuit, the LM26001 employs frequency foldback as a
second level of protection. If the feedback voltage falls below the short circuit threshold of 0.9 V, operating
frequency is reduced, thereby reducing average switch current. This is especially helpful in short circuit
conditions, when inductor current can rise very high during the minimum on-time. Frequency reduction begins at
20% below the nominal frequency setting. The minimum operating frequency in foldback mode is 71 kHz typical.
If the FB voltage falls below the frequency foldback threshold during frequency synchronized operation, the
SYNC function is disabled. Operating frequency versus FB voltage in short circuit conditions is shown in the
Typical Characteristics section.
Under conditions where the on time is close to minimum (less than 200 nsec typically), such as high input
voltage and high switching frequency, the current limit may not function properly. This is because the current limit
circuit cannot reduce the on-time below minimum which prevents entry into frequency foldback mode. There are
two ways to ensure proper current limit and foldback operation under high input voltage conditions. First, the
operating frequency can be reduced to increase the nominal on time. Second, the inductor value can be
increased to slow the current ramp and reduce the peak over-current.
7.3.6 Frequency Adjustment and Synchronization
The switching frequency of the LM26001 can be adjusted between 150 kHz and 500 kHz using a single external
resistor. This resistor is connected from the FREQ pin to ground as shown in the typical application. The resistor
value can be calculated with the following empirically derived equation:
-1.042
RFREQ = (6.25 x 1010) x fSW
(7)
14
Submit Documentation Feedback
Copyright © 2006–2015, Texas Instruments Incorporated
Product Folder Links: LM26001 LM26001-Q1
LM26001, LM26001-Q1
www.ti.com
SNVS430I –MAY 2006–REVISED MARCH 2015
Feature Description (continued)
600
500
400
300
200
100
0
50
100
150
200
250
300
R
FREQ
(k:)
Figure 18. Switching Frequency vs RFREQ
The switching frequency can also be synchronized to an external clock signal using the SYNC pin. The SYNC
pin allows the operating frequency to be varied above and below the nominal frequency setting. The adjustment
range is from 30% above nominal to 20% below nominal. External synchronization requires a 1.2V (typical) peak
signal level at the SYNC pin. The FREQ resistor must always be connected to initialize the nominal operating
frequency. The operating frequency is synchronized to the falling edge of the SYNC input. When SYNC goes
low, the high-side switch turns on. This allows any duty cycle to be used for the sync signal when synchronizing
to a frequency higher than nominal. When synchronizing to a lower frequency, however, there is a minimum duty
cycle requirement for the SYNC signal, given in the equation below:
fsync
Sync_Dmin
1 -
t
fnom
(8)
Where fnom is the nominal switching frequency set by the FREQ resistor, and fsync is a square wave. If the
SYNC pin is not used, it must be pulled low for normal operation. A 10 kΩ pull-down resistor is recommended to
protect against a missing sync signal. Although the LM26001 is designed to operate at up to 500 kHz, maximum
load current may be limited at higher frequencies due to increased temperature rise. See the Thermal
Considerations and TSD section.
7.3.7 VBIAS
The VBIAS pin is used to bypass the internal regulator which provides the bias voltage to the LM26001. When
the VBIAS pin is connected to a voltage greater than 3 V, the internal regulator automatically switches over to the
VBIAS input. This reduces the current into VIN (Iq) and increases system efficiency. Using the VBIAS pin has the
added benefit of reducing power dissipation within the device.
For most applications where 3 V < Vout < 10V, VBIAS can be connected to Vout. If not used, VBIAS should be
tied to GND.
If VBIAS drops below 2.9 V (typical), the device automatically switches over to supply the internal bias voltage
from Vin.
7.3.8 Low VIN Operation and UVLO
The LM26001 is designed to remain operational during short line transients when input voltage may drop as low
as 3.0 V. Minimum nominal operating input voltage is 4.0 V. Below this voltage, switch RDS(ON) increases, due to
the lower gate drive voltage from VDD. The minimum voltage required at VDD is approximately 3.5 V for normal
operation within specification.
VDD can also be used as a pull-up voltage for functions such as PGOOD and FPWM. Note that if VDD is used
externally, the pin is not recommended for loads greater than 1 mA.
Copyright © 2006–2015, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: LM26001 LM26001-Q1
LM26001, LM26001-Q1
SNVS430I –MAY 2006–REVISED MARCH 2015
www.ti.com
Feature Description (continued)
If the input voltage approaches the nominal output voltage, the duty cycle is maximized to hold up the output
voltage. In this mode of operation, once the duty cycle reaches its maximum, the LM26001 can skip a maximum
of seven off pulses, effectively increasing the duty cycle and thus minimizing the dropout from input to output.
Typical off-pulse skipping waveforms are shown in Figure 19.
Vout
20 mV/Div
IL
100 mA/Div
V
SW
2V/Div
4 Ps/DIV
Figure 19. Off-pulse Skipping Waveforms Vin = 3.5 V, Vnom = 3.3 V, fnom = 305 kHz
UVLO is sensed at both VIN and VDD, and is activated when either voltage falls below 2.9 V (typical). Although
VDD is typically less than 200 mV below VIN, it will not discharge through VIN. Therefore when the VIN voltage
drops rapidly, VDD may remain high, especially in sleep mode. For fast line voltage transients, using a larger
capacitor at the VDD pin can help to hold off a UVLO shutdown by extending the VDD discharge time. By
holding up VDD, a larger cap can also reduce the RDS(ON) (and dropout voltage) in low VIN conditions.
Alternately, under heavy loading the VDD voltage can fall several hundred mV below VIN. In this case, UVLO
may be triggered by VDD even though the VIN voltage is above the UVLO threshold.
When UVLO is activated the LM26001 enters a standby state in which VDD remains charged. As input voltage
and VDD voltage rise above 3.9 V (typical) the device will restart from softstart mode.
7.3.9 PGOOD
A power good pin, PGOOD, is available to monitor the output voltage status. The pin is internally connected to
an open-drain MOSFET, which remains open while the output voltage is within operating range. PGOOD goes
low (low impedance to ground) when the output falls below 85% of nominal or EN is pulled low. When the output
voltage returns to within 92% of nominal, as measured at the FB pin, PGOOD returns to a high state. For
improved noise immunity, there is a 5 µs delay between the PGOOD threshold and the PGOOD pin going low.
7.4 Device Functional Modes
The LM26001 has three basic operation mode: Shutdown, Sleep or light load operation and full operation.
The part enters shutdown mode when the EN pin is pulled low. In this mode the converter is disabled and the
quiescent current minimized See Enable for more details.
The part enters sleep mode when the converter is active (EN high) and the output current is low. Sleep mode is
activated as the COMP voltage naturally falls below a typical 0.6V threshold in light load operation. When
operating in sleep mode, the switching events of the converter are reduced in order to lower the current
consumption of the system. Forcing the FPWM pin high will prevent sleep mode operation. For details of
operation in sleep mode as well as entering and exiting sleep mode. See Sleep Mode.
When the part in enabled and the output load is higher, the part will be in full PWM operation.
In addition to these normal functioning modes, the LM26001 has a frequency foldback operating mode which
reduces the operating frequency to protect from short circuits. See Current Limit.
16
Submit Documentation Feedback
Copyright © 2006–2015, Texas Instruments Incorporated
Product Folder Links: LM26001 LM26001-Q1
LM26001, LM26001-Q1
www.ti.com
SNVS430I –MAY 2006–REVISED MARCH 2015
8 Applications and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The LM26001 offers efficient step-down function meeting the requirements of automotive applications. Current
mode control ensures smooth and safe operation thanks to its cycle by cycle current limiting function. Its low
minimum ON time allows it to operate over a wide range of output voltages. The following sections detail the
steps required for designing a successful application with the LM26001 from component selection to layout.
8.2 Typical Application
Figure 20 shows a complete typical application schematic. The components have been selected based on the
design criteria given in the following sections.
VIN : 4V - 38V
C1
3.3 PF
50V
C2
47 PF
50V
+
L
1
2
12
16
22 PH
3.5A
VIN
VIN
VBIAS
SW
VOUT : 3.3V
15
3
4
C6
+
D1
3A
60V
PGOOD
EN
SW
100 PF
C4
0.1 PF
R1
56k
1%
PGOOD
R4
14
7
12 m:
BOOT
200k
EN
LM26001
11
VDD
SYNC
SS
FB
5
9
6
13
8
COMP
Ref # Manufacturer
Part Number
R2
33k
1%
C8
4.7 nF
SYNC
C1
C2
C6
TDK
3225JB1H335K
EEVFK1H470P
C5
10 nF
FREQ
FPWM
VDD
GND
Panasonic
R6
10k
10
C9
47 pF
R3
120k
1%
Panasonic
NIEC
EEFVEOK101R
NSQ03A06
R5
15k
EP
17
C3
10 PF
D1
L1
SLF12565T-
220M3R5
TDK
Figure 20. Example Circuit 1.5A Max, 305 kHz
8.2.1 Design Requirements
The following parameters are needed to properly design the application and size the components:
PARAMETERS
Vout
VALUES
Output voltage
Vin min
Vin max
Iout max
Fsw
Maximum input voltage
Minimum input voltage
Maximum output current
Switching Frequency
Bandwidth of the converter
Fbw
8.2.2 Detailed Design Procedure
8.2.2.1 Setting Output Voltage
The output voltage is set by the ratio of a voltage divider at the FB pin as shown in the typical application. The
resistor values can be determined by the following equation:
Copyright © 2006–2015, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links: LM26001 LM26001-Q1
LM26001, LM26001-Q1
SNVS430I –MAY 2006–REVISED MARCH 2015
www.ti.com
R1
R2 =
Vout
§
·
¹
-1
©
Vfb
(9)
Where Vfb = 1.234V typically.
A maximum value of 150kΩ is recommended for the sum of R1 and R2.
As input voltage decreases towards the nominal output voltage, the LM26001 can skip up to seven off-pulses as
described in the Low VIN Operation and UVLO section. In low output voltage applications, if the on-time reaches
TonMIN, the device will skip on-pulses to maintain regulation. There is no limit to the number of pulses that are
skipped. In this mode of operation, however, output ripple voltage may increase slightly.
8.2.2.2 Inductor
The output inductor should be selected based on inductor ripple current. The amount of inductor ripple current
compared to load current, or ripple content, is defined as Iripple/Iload. Ripple content should be less than 40%.
Inductor ripple current, Iripple, can be calculated as shown below:
(Vin ± Vout) x Vout
Iripple =
fsw x L x Vin
(10)
Larger ripple content increases losses in the inductor and reduces the effective current limit.
Larger inductance values result in lower output ripple voltage and higher efficiency, but a slightly degraded
transient response. Lower inductance values allow for smaller case size, but the increased ripple lowers the
effective current limit threshold.
Remember that inductor value also affects the sleep mode threshold as shown in Figure 16.
When choosing the inductor, the saturation current rating must be higher than the maximum peak inductor
current and the RMS current rating should be higher than the maximum load current. Peak inductor current,
Ipeak, is calculated as:
Iripple
Ipeak = Iload +
2
(11)
For example, at a maximum load of 1.5A and a ripple content of 40%, peak inductor current is equal to 1.8A
which is safely below the minimum current limit of 1.85A. By increasing the inductor size, ripple content and peak
inductor current are lowered, which increases the current limit margin.
The size of the output inductor can also be determined using the desired output ripple voltage, Vrip. The
equation to determine the minimum inductance value based on Vrip is as follows:
(Vin ± Vout) x Vout x Re
LMIN
=
Vin x fsw x Vrip
(12)
Where Re is the ESR of the output capacitors, and Vrip is a peak-to-peak value. This equation assumes that the
output capacitors have some amount of ESR. It does not apply to ceramic output capacitors.
If this method is used, ripple content should still be verified to be less than 40%.
8.2.2.3 Output Capacitor
The primary criterion for selecting an output capacitor is equivalent series resistance, or ESR.
ESR (Re) can be selected based on the requirements for output ripple voltage and transient response. Once an
inductor value has been selected, ripple voltage can be calculated for a given Re using the equation above for
Lmin. Lower ESR values result in lower output ripple.
Re can also be calculated from the following equation:
'Vt
ReMAX
=
'It
(13)
18
Submit Documentation Feedback
Copyright © 2006–2015, Texas Instruments Incorporated
Product Folder Links: LM26001 LM26001-Q1
LM26001, LM26001-Q1
www.ti.com
SNVS430I –MAY 2006–REVISED MARCH 2015
Where ΔVt is the allowed voltage excursion during a load transient, and ΔIt is the maximum expected load
transient. If the total ESR is too high, the load transient requirement cannot be met, no matter how large the
output capacitance. If the ESR criteria for ripple voltage and transient excursion cannot be met, more capacitors
should be used in parallel. For non-ceramic capacitors, the minimum output capacitance is of secondary
importance, and is determined only by the load transient requirement.
If there is not enough capacitance, the output voltage excursion will exceed the maximum allowed value even if
the maximum ESR requirement is met. The minimum capacitance is calculated as follows:
§
('Vt)2 - ('It x Re)2
§
'Vt -
L x
©
CMIN
=
Vout x Re2
(14)
It is assumed the total ESR, Re, is no greater than ReMAX. Also, it is assumed that L has already been selected.
Generally speaking, the output capacitance requirement decreases with Re, ΔIt, and L. A typical value greater
than 100 µF works well for most applications.
8.2.2.4 Input Capacitor
In a switching converter, very fast switching pulse currents are drawn from the input rail. Therefore, input
capacitors are required to reduce noise, EMI, and ripple at the input to the LM26001. Capacitors must be
selected that can handle both the maximum ripple RMS current at highest ambient temperature as well as the
maximum input voltage. The equation for calculating the RMS input ripple current is shown below:
Vout x (Vin ± Vout)
Iload x
Irms =
Vin
(15)
For noise suppression, a ceramic capacitor in the range of 1.0 µF to 10 µF should be placed as close as possible
to the VIN pin.
A larger, high ESR input capacitor should also be used. This capacitor is recommended for damping input
voltage spikes during power-on and for holding up the input voltage during transients. In low input voltage
applications, line transients may fall below the UVLO threshold if there is not enough input capacitance. Both
tantalum and electrolytic type capacitors are suitable for the bulk capacitor. However, large tantalums may not be
available for high input voltages and their working voltage must be derated by at least 2X.
8.2.2.5 Bootstrap
The drive voltage for the internal switch is supplied via the BOOT pin. This pin must be connected to a ceramic
capacitor, Cboot, from the switch node, shown as C4 in the typical application. The LM26001 provides the VDD
voltage internally, so no external diode is needed. A maximum value of 0.1 uF is recommended for Cboot.
Values smaller than 0.01 uF may result in insufficient hold up time for the drive voltage and increased power
dissipation.
During low Vin operation, when the on-time is extended, the bootstrap capacitor is at risk of discharging. If the
Cboot capacitor is discharged below approximately 2.5V, the LM26001 enters a high frequency re-charge mode.
The Cboot cap is re-charged via the LG synchronous FET shown in the block diagram. Switching returns to
normal when the Cboot cap has been recharged.
8.2.2.6 Catch Diode
When the internal switch is off, output current flows through the catch diode. Alternately, when the switch is on,
the diode sees a reverse voltage equal to Vin. Therefore, the important parameters for selecting the catch diode
are peak current and peak inverse voltage. The average current through the diode is given by:
IDAVE = Iload x (1-D)
(16)
Where D is the duty cycle, defined as Vout/Vin. The catch diode conducts the largest currents during the lowest
duty cycle. Therefore IDAVE should be calculated assuming maximum input voltage. The diode should be rated to
handle this current continuously. For over-current or short circuit conditions, the catch diode should be rated to
handle peak currents equal to the peak current limit.
The peak inverse voltage rating of the diode must be greater than maximum input voltage.
Copyright © 2006–2015, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Links: LM26001 LM26001-Q1
LM26001, LM26001-Q1
SNVS430I –MAY 2006–REVISED MARCH 2015
www.ti.com
A Schottky diode must be used. It's low forward voltage maximizes efficiency and BOOT voltage, while also
protecting the SW pin against large negative voltage spikes.
8.2.2.7 Compensation
The purpose of loop compensation is to ensure stable operation while maximizing dynamic performance. Stability
can be analyzed with loop gain measurements, while dynamic performance is analyzed with both loop gain and
load transient response. Loop gain is equal to the product of control-output transfer function (power stage) and
the feedback transfer function (the compensation network).
For stability purposes, our target is to have a loop gain slope that is -20dB /decade from a very low frequency to
beyond the crossover frequency. Also, the crossover frequency should not exceed one-fifth of the switching
frequency, i.e. 60 kHz in the case of 300 kHz switching frequency.
For dynamic purposes, the higher the bandwidth, the faster the load transient response. A large DC gain means
high DC regulation accuracy (i.e. DC voltage changes little with load or line variations). To achieve this loop gain,
the compensation components should be set according to the shape of the control-output bode plot. A typical
plot is shown in Figure 21.
fp
fz
fn
0
20
0
-45
-20
-40
-60
-90
-135
-180
1000
0.01
0.1
1
10
100
FREQUENCY (kHz)
Figure 21. Control-Output Transfer Function
The control-output transfer function consists of one pole (fp), one zero (fz), and a double pole at fn (half the
switching frequency).
Referring to Figure 21, the following should be done to create a -20dB /decade roll-off of the loop gain:
1. Place a pole at 0 Hz (fpc)
2. Place a zero at fp (fzc)
3. Place a second pole at fz (fpc1)
The resulting feedback (compensation) bode plot is shown in Figure 22. Adding the control-output response to
the feedback response will then result in a nearly continuous –20db/decade slope.
0dB/dec
B
fzc
fpc1
fpc
(0Hz)
FREQUENCY
Figure 22. Feedback Transfer Function
20
Submit Documentation Feedback
Copyright © 2006–2015, Texas Instruments Incorporated
Product Folder Links: LM26001 LM26001-Q1
LM26001, LM26001-Q1
www.ti.com
SNVS430I –MAY 2006–REVISED MARCH 2015
The control-output corner frequencies can be determined approximately by the following equations:
1
fz =
2S x Re x Co
(17)
0.5
1
+
fp =
2 x S x L x fsw x Co
10 x S x Ro x Co
(18)
(19)
fsw
2
fn =
Where Co is the output capacitance, Ro is the load resistance, Re is the output capacitor ESR, and fsw is the
switching frequency. The effects of slope compensation and current sense gain are included in this equation.
However, the equation is an approximation intended to simplify loop compensation calculations. To derive the
exact transfer function, use 0.2V/V sense amp gain and 36mVp-p slope compensation.
Since fp is determined by the output network, it shifts with loading. Determine the range of frequencies
(fpmin/max) across the expected load range. Then determine the compensation values as described below and
shown in Figure 23.
5
SS
6
COMP
7
FB
C8
R5
C9
C10
R2
R1
To Vout
Figure 23. Compensation Network
1. The compensation network automatically introduces a low frequency pole (fpc), which is close to 0Hz.
2. Once the fp range is determined, R5 should be calculated using:
B
R1 + R2
R2
§
©
·
¹
x
R5 =
gm
(20)
Where B is the desired feedback gain in v/v between fp and fz, and gm is the transconductance of the error
amplifier. A gain value around 10dB (3.3v/v) is generally a good starting point. Bandwidth increases with
increasing values of R5.
3. Next, place a zero (fzc) near fp using C8. C8 can be determined with the following equation:
1
C8 =
2 x S x fPMAX x R5
(21)
The selected value of C8 should place fzc within a decade above or below fpmax, and not less than fpmin. A
higher C8 value (closer to fpmin) generally provides a more stable loop, but too high a value will slow the
transient response time. Conversely, a smaller C8 value will result in a faster transient response, but lower phase
margin.
4. A second pole (fpc1) can also be placed at fz. This pole can be created with a single capacitor, C9. The
minimum value for this capacitor can be calculated by:
1
C9 =
2 x S x fz x R5
(22)
C9 may not be necessary in all applications. However if the operating frequency is being synchronized below the
nominal frequency, C9 is recommended. Although it is not required for stability, C9 is very helpful in suppressing
noise.
Copyright © 2006–2015, Texas Instruments Incorporated
Submit Documentation Feedback
21
Product Folder Links: LM26001 LM26001-Q1
LM26001, LM26001-Q1
SNVS430I –MAY 2006–REVISED MARCH 2015
www.ti.com
A phase lead capacitor can also be added to increase the phase and gain margins. The phase lead capacitor is
most helpful for high input voltage applications or when synchronizing to a frequency greater than nominal. This
capacitor, shown as C10 in Figure 23, should be placed in parallel with the top feedback resistor, R1. C10
introduces an additional zero and pole to the compensation network. These frequencies can be calculated as
shown below:
1
fzff =
2 x S x R1 x C10
(23)
fzff x Vout
fpff =
Vfb
(24)
A phase lead capacitor will boost loop phase around the region of the zero frequency, fzff. fzff should be placed
somewhat below the fpz1 frequency set by C9. However, if C10 is too large, it will have no effect.
8.2.3 Application Curves
Vout
Vout
1V/Div
40 mV/Div
PGOOD
5V/Div
Iout
500 mA/Div
SS
1V/Div
EN
10V/Div
1 Ps/DIV
200 Ps/DIV
Figure 24. Startup Waveforms
Figure 25. Load Transient Response
22
Submit Documentation Feedback
Copyright © 2006–2015, Texas Instruments Incorporated
Product Folder Links: LM26001 LM26001-Q1
LM26001, LM26001-Q1
www.ti.com
SNVS430I –MAY 2006–REVISED MARCH 2015
9 Power Supply Recommendations
The LM26001 is designed to operate from various DC power supply including a car battery. If so, VIN input
should be protected from reversal voltage and voltage dump over 48 Volts. The impedance of the input supply
rail should be low enough that the input current transient does not cause drop below VIN UVLO level. If the input
supply is connected by using long wires, additional bulk capacitance may be required in addition to normal input
capacitor.
10 Layout
10.1 Layout Guidelines
Good board layout is critical for switching regulators such as the LM26001. First, the ground plane area must be
sufficient for thermal dissipation purposes, and second, appropriate guidelines must be followed to reduce the
effects of switching noise.
Switch mode converters are very fast switching devices. In such devices, the rapid increase of input current
combined with parasitic trace inductance generates unwanted Ldi/dt noise spikes at the SW node and also at the
VIN node. The magnitude of this noise tends to increase as the output current increases. This parasitic spike
noise may turn into electromagnetic interference (EMI), and can also cause problems in device performance.
Therefore, care must be taken in layout to minimize the effect of this switching noise.
The current sensing circuit in current mode devices can be easily affected by switching noise. This noise can
cause duty cycle jitter which leads to increased spectral noise. Although the LM26001 has 100ns blanking time at
the beginning of every cycle to ignore this noise, some noise may remain after the blanking time. Following the
important guidelines below will help minimize switching noise and its effect on current sensing.
The switch node area should be as small as possible. The catch diode, input capacitors, and output capacitors
should be grounded to a large ground plane, with the bulk input capacitor grounded as close as possible to the
catch diode anode. Additionally, the ground area between the catch diode and bulk input capacitor is very noisy
and should be somewhat isolated from the rest of the ground plane.
A ceramic input capacitor must be connected as close as possible to the VIN pin and grounded close to the GND
pin. Often this capacitor is most easily located on the bottom side of the pcb. If placement close to the GND pin
is not practical, the ceramic input capacitor can also be grounded close to the catch diode ground. The above
layout recommendations are illustrated below in Figure 26.
It is a good practice to connect the EP, GND pin, and small signal components (COMP, FB, FREQ) to a separate
ground plane, shown in Figure 26 as EP GND, and in the schematics as a signal ground symbol. Both the
exposed pad and the GND pin must be connected to ground. This quieter plane should be connected to the high
current ground plane at a quiet location, preferably near the Vout ground as shown by the dashed line in
Figure 26.
The EP GND plane should be made as large as possible, since it is also used for thermal dissipation. Several
vias can be placed directly below the EP to increase heat flow to other layers when they are available. The
recommended via hole diameter is 0.3mm.
The trace from the FB pin to the resistor divider should be short and the entire feedback trace must be kept away
from the inductor and switch node. See AN-1229 SIMPLE SWITCHER® PCB Layout Guidelines, SNVA054, for
more information regarding PCB layout for switching regulators.
Copyright © 2006–2015, Texas Instruments Incorporated
Submit Documentation Feedback
23
Product Folder Links: LM26001 LM26001-Q1
LM26001, LM26001-Q1
SNVS430I –MAY 2006–REVISED MARCH 2015
www.ti.com
10.2 Layout Example
Vout
Vin
GND
SW
EP
GND
Figure 26. Example PCB Layout
10.3 Thermal Considerations and TSD
Although the LM26001 has a built in current limit, at ambient temperatures above 80°C, device temperature rise
may limit the actual maximum load current. Therefore, temperature rise must be taken into consideration to
determine the maximum allowable load current.
Temperature rise is a function of the power dissipation within the device. The following equations can be used to
calculate power dissipation (PD) and temperature rise, where total PD is the sum of FET switching losses, FET
DC losses, drive losses, Iq, and VBIAS losses:
PDTOTAL = PswAC + PswDC + PQG + PIq + PVBIAS
(25)
Vin x 10-9
1.33
§
©
·
¹
PswAC = Vin x Iload x fsw x
(26)
(27)
(28)
(29)
(30)
PswDC = D x Iload2 x (0.2 + 0.00065 x (Tj - 25))
PQG = Vin x 4.6 x 10-9 x fsw
PIq = Vin x Iq
PVBIAS = Vbias x IVBIAS
Given this total power dissipation, junction temperature can be calculated as follows:
Tj = Ta + (PDTOTAL x θJA)
(31)
Where θJA=38°C/W (typically) when using a multi-layer board with a large copper plane area. θJA varies with
board type and metallization area.
To calculate the maximum allowable power dissipation, assume Tj = 125°C. To ensure that junction temperature
does not exceed the maximum operating rating of 125°C, power dissipation should be verified at the maximum
expected operating frequency, maximum ambient temperature, and minimum and maximum input voltage. The
calculated maximum load current is based on continuous operation and may be exceeded during transient
conditions.
If the power dissipation remains above the maximum allowable level, device temperature will continue to rise.
When the junction temperature exceeds its maximum, the LM26001 engages Thermal Shut Down (TSD). In
TSD, the part remains in a shutdown state until the junction temperature falls to within normal operating limits. At
this point, the device restarts in soft-start mode.
24
Submit Documentation Feedback
Copyright © 2006–2015, Texas Instruments Incorporated
Product Folder Links: LM26001 LM26001-Q1
LM26001, LM26001-Q1
www.ti.com
SNVS430I –MAY 2006–REVISED MARCH 2015
11 Device and Documentation Support
11.1 Documentation Support
11.1.1 Related Documentation
AN-1229 SIMPLE SWITCHER® PCB Layout Guidelines, SNVA054
IC Package Thermal Metrics application report, SPRA953
11.2 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 1. Related Links
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
PARTS
PRODUCT FOLDER
SAMPLE & BUY
LM26001
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
LM26001-Q1
11.3 Trademarks
All trademarks are the property of their respective owners.
11.4 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.5 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2006–2015, Texas Instruments Incorporated
Submit Documentation Feedback
25
Product Folder Links: LM26001 LM26001-Q1
PACKAGE OPTION ADDENDUM
www.ti.com
25-Feb-2015
PACKAGING INFORMATION
Orderable Device
LM26001MXA/NOPB
LM26001MXAX/NOPB
LM26001QMXA/NOPB
LM26001QMXAX/NOPB
Status Package Type Package Pins Package
Eco Plan
Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-40 to 125
-40 to 125
-40 to 125
-40 to 125
Device Marking
Samples
Drawing
Qty
(1)
(2)
(6)
(3)
(4/5)
ACTIVE
HTSSOP
HTSSOP
HTSSOP
HTSSOP
PWP
16
16
16
16
92
Green (RoHS
& no Sb/Br)
CU SN
CU SN
CU SN
CU SN
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
L26001
MXA
ACTIVE
ACTIVE
ACTIVE
PWP
PWP
PWP
2500
92
Green (RoHS
& no Sb/Br)
L26001
MXA
Green (RoHS
& no Sb/Br)
L26001
QMXA
2500
Green (RoHS
& no Sb/Br)
L26001
QMXA
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
25-Feb-2015
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF LM26001, LM26001-Q1 :
Catalog: LM26001
•
Automotive: LM26001-Q1
•
NOTE: Qualified Version Definitions:
Catalog - TI's standard catalog product
•
Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
•
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
6-Nov-2015
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LM26001MXAX/NOPB HTSSOP PWP
LM26001QMXAX/NOPB HTSSOP PWP
16
16
2500
2500
330.0
330.0
12.4
12.4
6.95
6.95
5.6
5.6
1.6
1.6
8.0
8.0
12.0
12.0
Q1
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
6-Nov-2015
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
LM26001MXAX/NOPB
LM26001QMXAX/NOPB
HTSSOP
HTSSOP
PWP
PWP
16
16
2500
2500
367.0
367.0
367.0
367.0
35.0
35.0
Pack Materials-Page 2
MECHANICAL DATA
PWP0016A
MXA16A (Rev A)
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
LM26001MXA/NOPB CAD模型
引脚图
封装焊盘图
LM26001MXA/NOPB 替代型号
| 型号 | 制造商 | 描述 | 替代类型 | 文档 |
| LM26001MXAX/NOPB | TI | LM26001/-Q1 1.5-A Switching Regulator With High-Efficiency Sleep Mode | 类似代替 |
|
| LM26001QMXA/NOPB | TI | LM26001/-Q1 1.5-A Switching Regulator With High-Efficiency Sleep Mode | 类似代替 |
|
| LM26001QMXAX/NOPB | TI | LM26001/-Q1 1.5-A Switching Regulator With High-Efficiency Sleep Mode | 类似代替 |
|
LM26001MXA/NOPB 相关器件
| 型号 | 制造商 | 描述 | 价格 | 文档 |
| LM26001MXAX | NSC | 1.5A Switching Regulator with High Efficiency Sleep MODE | 获取价格 |
|
| LM26001MXAX/NOPB | TI | LM26001/-Q1 1.5-A Switching Regulator With High-Efficiency Sleep Mode | 获取价格 |
|
| LM26001QMXA | NSC | IC 3.2 A SWITCHING REGULATOR, 500 kHz SWITCHING FREQ-MAX, PDSO16, PLASTIC, TSSOP-16, Switching Regulator or Controller | 获取价格 |
|
| LM26001QMXA/NOPB | TI | LM26001/-Q1 1.5-A Switching Regulator With High-Efficiency Sleep Mode | 获取价格 |
|
| LM26001QMXAX | NSC | IC 3.2 A SWITCHING REGULATOR, 500 kHz SWITCHING FREQ-MAX, PDSO16, PLASTIC, TSSOP-16, Switching Regulator or Controller | 获取价格 |
|
| LM26001QMXAX/NOPB | TI | LM26001/-Q1 1.5-A Switching Regulator With High-Efficiency Sleep Mode | 获取价格 |
|
| LM26001_0609 | NSC | 1.5A Switching Regulator with High Efficiency Sleep Mode | 获取价格 |
|
| LM26001_08 | NSC | 1.5A Switching Regulator with High Efficiency Sleep Mode | 获取价格 |
|
| LM26001_15 | TI | LM26001/-Q1 1.5-A Switching Regulator With High-Efficiency Sleep Mode | 获取价格 |
|
| LM26003 | NSC | 3A Switching Regulator with High Efficiency Sleep Mode | 获取价格 |
|
LM26001MXA/NOPB 相关文章
Bourns 密封通孔金属陶瓷微调电位计产品选型手册(英文版)
- 2024-09-20
- 5
Bourns 精密环境传感器产品选型手册(英文版)
- 2024-09-20
- 8
Bourns POWrTher 负温度系数(NTC)热敏电阻手册 (英文版)
- 2024-09-20
- 8
Bourns GMOV 混合过压保护组件产品选型手册(英文版)
- 2024-09-20
- 6
