LM2673SDX-ADJ [TI]
LM2673 SIMPLE SWITCHER 3A Step-Down Voltage Regulator with Adjustable Current; LM2673 SIMPLE SWITCHER 3A降压型稳压器具有可调电流型号: | LM2673SDX-ADJ |
厂家: | TEXAS INSTRUMENTS |
描述: | LM2673 SIMPLE SWITCHER 3A Step-Down Voltage Regulator with Adjustable Current |
文件: | 总35页 (文件大小:1431K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LM2673
www.ti.com
SNVS030N –APRIL 2000–REVISED APRIL 2013
®
LM2673 SIMPLE SWITCHER 3A Step-Down Voltage Regulator with Adjustable Current
Limit
Check for Samples: LM2673
1
FEATURES
DESCRIPTION
The LM2673 series of regulators are monolithic
integrated circuits which provide all of the active
functions for a step-down (buck) switching regulator
capable of driving up to 3A loads with excellent line
and load regulation characteristics. High efficiency
(>90%) is obtained through the use of a low ON-
resistance DMOS power switch. The series consists
of fixed output voltages of 3.3V, 5V and 12V and an
adjustable output version.
23
•
Efficiency Up to 94%
•
Simple and Easy to Design with (Using Off-
The-Shelf External Components)
•
Resistor Programmable Peak Current Limit
Over a Range of 2A to 5A
•
•
150 mΩ DMOS Output Switch
3.3V, 5V and 12V Fixed Output and Adjustable
(1.2V to 37V) Versions
The SIMPLE SWITCHER® concept provides for a
complete design using a minimum number of external
•
±2% Maximum Output Tolerance Over Full
Line and Load Conditions
components.
A
high fixed frequency oscillator
•
•
•
•
Wide Input Voltage Range: 8V to 40V
260 KHz Fixed Frequency Internal Oscillator
Softstart Capability
(260KHz) allows the use of physically smaller sized
components. A family of standard inductors for use
with the LM2673 are available from several
manufacturers to greatly simplify the design process.
−40 to +125°C Operating Junction Temperature
Range
Other features include the ability to reduce the input
surge current at power-ON by adding a softstart
timing capacitor to gradually turn on the regulator.
The LM2673 series also has built in thermal
shutdown and resistor programmable current limit of
the power MOSFET switch to protect the device and
load circuitry under fault conditions. The output
voltage is ensured to a ±2% tolerance. The clock
frequency is controlled to within a ±11% tolerance.
APPLICATIONS
•
•
•
Simple to Design, High Efficiency (>90%) Step-
Down Switching Regulators
Efficient System Pre-Regulator for Linear
Voltage Regulators
Battery Chargers
Typical Application
Feedback
0.01 mF
Input
Voltage
V
IN
Boost
Output
LM2673 - 5.0
L
8V to 40V
Voltage
0.47 mF
+
+
Switch
Output
C
IN
2 x 15 mF/50V
5V/3A
33 mH
+
Softstart
8.2k
Ground
C
OUT
Current
Limit
Adjust
SR305
180 mF/16V
1 nF
37,125
I
=
CL
R
ADJ
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
SIMPLE SWITCHER, Switchers Made Simple are registered trademarks of Texas Instruments.
All other trademarks are the property of their respective owners.
2
3
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2000–2013, Texas Instruments Incorporated
LM2673
SNVS030N –APRIL 2000–REVISED APRIL 2013
www.ti.com
Connection Diagrams
Figure 1. DDPAK Package (Top View)
See Package Number KTW0007B
Figure 2. TO-220 Package (Top View)
See Package Number NDZ0007B
VSW
VSW
VSW
1
14
13
12
11
10
9
*
VIN
VIN
CB
2
3
4
5
6
7
DAP**
*
*
*
CURRENT ADJ
GND
FB
SOFTSTART
8
No Connections
*
Connect to Pin 9 on PCB
**
Figure 3. VSON-14 (Top View)
See Package Number NHM0014A
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings(1)(2)
Input Supply Voltage
Softstart Pin Voltage
Switch Voltage to Ground(3)
Boost Pin Voltage
45V
−0.1V to 6V
−1V to VIN
VSW + 8V
Feedback Pin Voltage
Power Dissipation
ESD(4)
−0.3V to 14V
Internally Limited
2 kV
Storage Temperature Range
Soldering Temperature
−65°C to 150°C
4 sec, 260°C
10 sec, 240°C
75 sec, 219°C
Wave
Infrared
Vapor Phase
(1) Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings indicate conditions under
which of the device is ensured. Operating Ratings do not imply ensured performance limits. For ensured performance limits and
associated test condition, see the Electrical Characteristics tables.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
(3) The absolute maximum specification of the 'Switch Voltage to Ground' applies to DC voltage. An extended negative voltage limit of -8V
applies to a pulse of up to 20 ns, -6V of 60 ns and -3V of up to 100 ns.
(4) ESD was applied using the human-body model, a 100pF capacitor discharged through a 1.5 kΩ resistor into each pin.
2
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM2673
LM2673
www.ti.com
SNVS030N –APRIL 2000–REVISED APRIL 2013
Operating Ratings
Supply Voltage
8V to 40V
Junction Temperature Range (TJ)
−40°C to 125°C
Electrical Characteristics
LM2673-3.3
Limits appearing in bold type face apply over the entire junction temperature range of operation, −40°C to 125°C.
Specifications appearing in normal type apply for TA = TJ = 25°C. RADJ = 8.2KΩ
Symbol
VOUT
η
Parameter
Output Voltage
Efficiency
Conditions
VIN = 8V to 40V, 100mA ≤ IOUT ≤ 3A
VIN = 12V, ILOAD = 3A
Typ(1)
Min(2)
Max(2)
Units
V
3.3
3.234/3.201
3.366/3.399
86
%
(1) Typical values are determined with TA = TJ = 25°C and represent the most likely norm.
(2) All limits are ensured at room temperature (standard type face) and at temperature extremes (bold type face). All room temperature
limits are 100% tested during production with TA = TJ = 25°C. All limits at temperature extremes are ensured via correlation using
standard Quality Control (SQC) methods. All limits are used to calculate Average Outgoing Quality Level (AOQL).
LM2673-5.0
Symbol
VOUT
η
Parameter
Output Voltage
Efficiency
Conditions
VIN = 8V to 40V, 100mA ≤ IOUT ≤ 3A
VIN = 12V, ILOAD = 3A
Typ(1)
5.0
Min(2)
Max(2)
Units
V
4.900/4.850
5.100/5.150
88
%
(1) Typical values are determined with TA = TJ = 25°C and represent the most likely norm.
(2) All limits are ensured at room temperature (standard type face) and at temperature extremes (bold type face). All room temperature
limits are 100% tested during production with TA = TJ = 25°C. All limits at temperature extremes are ensured via correlation using
standard Quality Control (SQC) methods. All limits are used to calculate Average Outgoing Quality Level (AOQL).
LM2673-12
Symbol
VOUT
η
Parameter
Output Voltage
Efficiency
Conditions
VIN = 15V to 40V, 100mA ≤ IOUT ≤ 3A
VIN = 24V, ILOAD = 3A
Typ(1)
12
Min(2)
Max(2)
Units
V
11.76/11.64
12.24/12.36
94
%
(1) Typical values are determined with TA = TJ = 25°C and represent the most likely norm.
(2) All limits are ensured at room temperature (standard type face) and at temperature extremes (bold type face). All room temperature
limits are 100% tested during production with TA = TJ = 25°C. All limits at temperature extremes are ensured via correlation using
standard Quality Control (SQC) methods. All limits are used to calculate Average Outgoing Quality Level (AOQL).
LM2673-ADJ
Symbol
Parameter
Conditions
Typ(1)
1.21
88
Min(2)
Max(2)
Units
V
VFB
Feedback Voltage VIN = 8V to 40V, 100mA ≤ IOUT ≤ 3A
1.186/1.174
1.234/1.246
VOUT Programmed for 5V
η
Efficiency
VIN = 12V, ILOAD = 3A
%
(1) Typical values are determined with TA = TJ = 25°C and represent the most likely norm.
(2) All limits are ensured at room temperature (standard type face) and at temperature extremes (bold type face). All room temperature
limits are 100% tested during production with TA = TJ = 25°C. All limits at temperature extremes are ensured via correlation using
standard Quality Control (SQC) methods. All limits are used to calculate Average Outgoing Quality Level (AOQL).
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LM2673
LM2673
SNVS030N –APRIL 2000–REVISED APRIL 2013
www.ti.com
All Output Voltage Versions
Electrical Characteristics
Limits appearing in bold type face apply over the entire junction temperature range of operation, −40°C to 125°C.
Specifications appearing in normal type apply for TA = TJ = 25°C. Unless otherwise specified, RADJ = 8.2KΩ, VIN=12V for the
3.3V, 5V and Adjustable versions and VIN=24V for the 12V version.
Symbol
Parameter
Conditions
Typ
Min
Max
Units
DEVICE PARAMETERS
IQ
Quiescent Current VFEEDBACK = 8V
4.2
6
mA
For 3.3V, 5.0V, and ADJ Versions
VFEEDBACK = 15V
For 12V Versions
VADJ
Current Limit
Adjust Voltage
1.21
4.5
1.181/1.169
3.8/3.6
1.229/1.246
5.25/5.4
V
A
ICL
IL
Current Limit
RADJ = 8.2KΩ(1)
Output Leakage
Current
VIN = 40V, Softstart Pin = 0V
VSWITCH = 0V
VSWITCH = −1V
mA
mA
1.0
6
1.5
15
RDS(ON)
Switch On-
Resistance
ISWITCH = 3A
0.15
0.17/0.29
Ω
fO
D
Oscillator
Frequency
Measured at Switch Pin
260
225
280
kHz
Duty Cycle
Maximum Duty Cycle
Minimum Duty Cycle
91
0
%
%
IBIAS
Feedback Bias
Current
VFEEDBACK = 1.3V
ADJ Version Only
85
nA
VSFST
ISFST
Softstart Threshold
Voltage
0.63
3.7
0.53
0.74
6.9
V
Softstart Pin
Current
Softstart Pin = 0V
μA
θJA
θJA
θJC
θJA
θJA
θJA
θJC
θJA
θJA
Thermal
Resistance
NDZ Package, Junction to Ambient(2)
NDZ Package, Junction to Ambient(3)
NDZ Package, Junction to Case
KTW Package, Junction to Ambient(4)
KTW Package, Junction to Ambient(5)
KTW Package, Junction to Ambient(6)
KTW Package, Junction to Case
65
45
2
56
35
26
2
°C/W
++
NHM Package, Junction to Ambient(7)
NHM Package, Junction to Ambient(8)
55
29
°C/W
(1) The peak switch current limit is determined by the following relationship: ICL=37,125/ RADJ
.
(2) Junction to ambient thermal resistance (no external heat sink) for the 7 lead TO-220 package mounted vertically, with ½ inch leads in a
socket, or on a PC board with minimum copper area.
(3) Junction to ambient thermal resistance (no external heat sink) for the 7 lead TO-220 package mounted vertically, with ½ inch leads
soldered to a PC board containing approximately 4 square inches of (1 oz.) copper area surrounding the leads.
(4) Junction to ambient thermal resistance for the 7 lead DDPAK mounted horizontally against a PC board area of 0.136 square inches (the
same size as the DDPAK package) of 1 oz. (0.0014 in. thick) copper.
(5) Junction to ambient thermal resistance for the 7 lead DDPAK mounted horizontally against a PC board area of 0.4896 square inches
(3.6 times the area of the DDPAK package) of 1 oz. (0.0014 in. thick) copper.
(6) Junction to ambient thermal resistance for the 7 lead DDPAK mounted horizontally against a PC board copper area of 1.0064 square
inches (7.4 times the area of the DDPAK package) of 1 oz. (0.0014 in. thick) copper. Additional copper area will reduce thermal
resistance further. See the thermal model in Switchers Made Simple® software.
(7) Junction to ambient thermal resistance for the 14-lead VSON mounted on a PC board copper area equal to the die attach paddle.
(8) Junction to ambient thermal resistance for the 14-lead VSON mounted on a PC board copper area using 12 vias to a second layer of
copper equal to die attach paddle. Additional copper area will reduce thermal resistance further. For layout recommendations, refer to
Application Note AN-1187 at www.ti.com/lsds/ti/analog/powermanagement/power_portal.page.
4
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM2673
LM2673
www.ti.com
SNVS030N –APRIL 2000–REVISED APRIL 2013
Typical Performance Characteristics
Normalized Output Voltage
Line Regulation
Figure 4.
Figure 5.
Efficiency vs Input Voltage
Efficiency vs ILOAD
Figure 6.
Figure 7.
Switch Current Limit
Operating Quiescent Current
Figure 8.
Figure 9.
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: LM2673
LM2673
SNVS030N –APRIL 2000–REVISED APRIL 2013
www.ti.com
Typical Performance Characteristics (continued)
Switching Frequency
Feedback Pin Bias Current
Figure 10.
Figure 11.
Load Transient Response for Continuous Mode
VIN = 20V, VOUT = 5V
L = 33 μH, COUT = 200 μF, COUTESR = 26 mΩ
Load Transient Response for Discontinuous Mode
VIN = 20V, VOUT = 5V,
L = 10 μH, COUT = 400 μF, COUTESR = 13 mΩ
A: Output Voltage, 100 mV//div, AC-Coupled.
B: Load Current: 500 mA to 3A Load Pulse
A: Output Voltage, 100 mV/div, AC-Coupled.
B: Load Current: 200 mA to 3A Load Pulse
Figure 13. Horizontal Time Base: 200 μs/div
Figure 12. Horizontal Time Base: 100 μs/div
Continuous Mode Switching Waveforms
VIN = 20V, VOUT = 5V, ILOAD = 3A
L = 33 μH, COUT = 200 μF, COUTESR = 26 mΩ
Discontinuous Mode Switching Waveforms
VIN = 20V, VOUT = 5V, ILOAD = 500 mA
L = 10 μH, COUT = 400 μF, COUTESR = 13 mΩ
A: VSW Pin Voltage, 10 V/div.
A: VSW Pin Voltage, 10 V/div.
B: Inductor Current, 1 A/div
B: Inductor Current, 1 A/div
C: Output Ripple Voltage, 20 mV/div AC-Coupled
C: Output Ripple Voltage, 20 mV/div AC-Coupled
Figure 14. Horizontal Time Base: 1 μs/div
Figure 15. Horizontal Time Base: 1 μs//iv
6
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM2673
LM2673
www.ti.com
SNVS030N –APRIL 2000–REVISED APRIL 2013
Block Diagram
* Active Inductor Patent Number 5,514,947
† Active Capacitor Patent Number 5,382,918
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: LM2673
LM2673
SNVS030N –APRIL 2000–REVISED APRIL 2013
www.ti.com
APPLICATION HINTS
The LM2673 provides all of the active functions required for a step-down (buck) switching regulator. The internal
power switch is a DMOS power MOSFET to provide power supply designs with high current capability, up to 3A,
and highly efficient operation.
The LM2673 is part of the SIMPLE SWITCHER family of power converters. A complete design uses a minimum
number of external components, which have been pre-determined from a variety of manufacturers. Using either
this data sheet or a design software program called LM267X Made Simple (version 2.0) a complete switching
power supply can be designed quickly. The software is provided free of charge and can be downloaded from
Texas Instrument's Internet site located at www.ti.com.
SWITCH OUTPUT
This is the output of a power MOSFET switch connected directly to the input voltage. The switch provides energy
to an inductor, an output capacitor and the load circuitry under control of an internal pulse-width-modulator
(PWM). The PWM controller is internally clocked by a fixed 260KHz oscillator. In a standard step-down
application the duty cycle (Time ON/Time OFF) of the power switch is proportional to the ratio of the power
supply output voltage to the input voltage. The voltage on pin 1 switches between Vin (switch ON) and below
ground by the voltage drop of the external Schottky diode (switch OFF).
INPUT
The input voltage for the power supply is connected to pin 2. In addition to providing energy to the load the input
voltage also provides bias for the internal circuitry of the LM2673. For ensured performance the input voltage
must be in the range of 8V to 40V. For best performance of the power supply the input pin should always be
bypassed with an input capacitor located close to pin 2.
C BOOST
A capacitor must be connected from pin 3 to the switch output, pin 1. This capacitor boosts the gate drive to the
internal MOSFET above Vin to fully turn it ON. This minimizes conduction losses in the power switch to maintain
high efficiency. The recommended value for C Boost is 0.01μF.
GROUND
This is the ground reference connection for all components in the power supply. In fast-switching, high-current
applications such as those implemented with the LM2673, it is recommended that a broad ground plane be used
to minimize signal coupling throughout the circuit
CURRENT ADJUST
A key feature of the LM2673 is the ability to tailor the peak switch current limit to a level required by a particular
application. This alleviates the need to use external components that must be physically sized to accommodate
current levels (under shorted output conditions for example) that may be much higher than the normal circuit
operating current requirements.
A resistor connected from pin 5 to ground establishes a current (I(pin 5) = 1.2V / RADJ) that sets the peak current
through the power switch. The maximum switch current is fixed at a level of 37,125 / RADJ
.
FEEDBACK
This is the input to a two-stage high gain amplifier, which drives the PWM controller. It is necessary to connect
pin 6 to the actual output of the power supply to set the dc output voltage. For the fixed output devices (3.3V, 5V
and 12V outputs), a direct wire connection to the output is all that is required as internal gain setting resistors are
provided inside the LM2673. For the adjustable output version two external resistors are required to set the dc
output voltage. For stable operation of the power supply it is important to prevent coupling of any inductor flux to
the feedback input.
8
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM2673
LM2673
www.ti.com
SNVS030N –APRIL 2000–REVISED APRIL 2013
SOFTSTART
A capacitor connected from pin 7 to ground allows for a slow turn-on of the switching regulator. The capacitor
sets a time delay to gradually increase the duty cycle of the internal power switch. This can significantly reduce
the amount of surge current required from the input supply during an abrupt application of the input voltage. If
softstart is not required this pin should be left open circuited. Please see the Css SOFTSTART CAPACITOR
section for further information regarding softstart capacitor values.
DAP (VSON PACKAGE)
The Die Attach Pad (DAP) can and should be connected to PCB Ground plane/island. For CAD and assembly
guidelines refer to Application Note AN-1187 at www.ti.com/lsds/ti/analog/powermanagement/power_portal.page.
DESIGN CONSIDERATIONS
Figure 16. Basic Circuit for Fixed Output Voltage Applications
Figure 17. Basic Circuit for Adjustable Output Voltage Applications
Power supply design using the LM2673 is greatly simplified by using recommended external components. A wide
range of inductors, capacitors and Schottky diodes from several manufacturers have been evaluated for use in
designs that cover the full range of capabilities (input voltage, output voltage and load current) of the LM2673. A
simple design procedure using nomographs and component tables provided in this data sheet leads to a working
design with very little effort. Alternatively, the design software, LM267X Made Simple (version 6.0), can also be
used to provide instant component selection, circuit performance calculations for evaluation, a bill of materials
component list and a circuit schematic.
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: LM2673
LM2673
SNVS030N –APRIL 2000–REVISED APRIL 2013
www.ti.com
The individual components from the various manufacturers called out for use are still just a small sample of the
vast array of components available in the industry. While these components are recommended, they are not
exclusively the only components for use in a design. After a close comparison of component specifications,
equivalent devices from other manufacturers could be substituted for use in an application.
Important considerations for each external component and an explanation of how the nomographs and selection
tables were developed follows.
INDUCTOR
The inductor is the key component in a switching regulator. For efficiency the inductor stores energy during the
switch ON time and then transfers energy to the load while the switch is OFF.
Nomographs are used to select the inductance value required for a given set of operating conditions. The
nomographs assume that the circuit is operating in continuous mode (the current flowing through the inductor
never falls to zero). The magnitude of inductance is selected to maintain a maximum ripple current of 30% of the
maximum load current. If the ripple current exceeds this 30% limit the next larger value is selected.
The inductors offered have been specifically manufactured to provide proper operation under all operating
conditions of input and output voltage and load current. Several part types are offered for a given amount of
inductance. Both surface mount and through-hole devices are available. The inductors from each of the three
manufacturers have unique characteristics.
Renco: ferrite stick core inductors; benefits are typically lowest cost and can withstand ripple and transient peak
currents above the rated value. These inductors have an external magnetic field, which may generate EMI.
Pulse Engineering: powdered iron toroid core inductors; these also can withstand higher than rated currents and,
being toroid inductors, will have low EMI.
Coilcraft: ferrite drum core inductors; these are the smallest physical size inductors and are available only as
surface mount components. These inductors also generate EMI but less than stick inductors.
OUTPUT CAPACITOR
The output capacitor acts to smooth the dc output voltage and also provides energy storage. Selection of an
output capacitor, with an associated equivalent series resistance (ESR), impacts both the amount of output ripple
voltage and stability of the control loop.
The output ripple voltage of the power supply is the product of the capacitor ESR and the inductor ripple current.
The capacitor types recommended in the tables were selected for having low ESR ratings.
In addition, both surface mount tantalum capacitors and through-hole aluminum electrolytic capacitors are offered
as solutions.
Impacting frequency stability of the overall control loop, the output capacitance, in conjunction with the inductor,
creates a double pole inside the feedback loop. In addition the capacitance and the ESR value create a zero.
These frequency response effects together with the internal frequency compensation circuitry of the LM2673
modify the gain and phase shift of the closed loop system.
As a general rule for stable switching regulator circuits it is desired to have the unity gain bandwidth of the circuit
to be limited to no more than one-sixth of the controller switching frequency. With the fixed 260KHz switching
frequency of the LM2673, the output capacitor is selected to provide a unity gain bandwidth of 40KHz maximum.
Each recommended capacitor value has been chosen to achieve this result.
In some cases multiple capacitors are required either to reduce the ESR of the output capacitor, to minimize
output ripple (a ripple voltage of 1% of Vout or less is the assumed performance condition), or to increase the
output capacitance to reduce the closed loop unity gain bandwidth (to less than 40KHz). When parallel
combinations of capacitors are required it has been assumed that each capacitor is the exact same part type.
10
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM2673
LM2673
www.ti.com
SNVS030N –APRIL 2000–REVISED APRIL 2013
The RMS current and working voltage (WV) ratings of the output capacitor are also important considerations. In a
typical step-down switching regulator, the inductor ripple current (set to be no more than 30% of the maximum
load current by the inductor selection) is the current that flows through the output capacitor. The capacitor RMS
current rating must be greater than this ripple current. The voltage rating of the output capacitor should be
greater than 1.3 times the maximum output voltage of the power supply. If operation of the system at elevated
temperatures is required, the capacitor voltage rating may be de-rated to less than the nominal room temperature
rating. Careful inspection of the manufacturer's specification for de-rating of working voltage with temperature is
important.
INPUT CAPACITOR
Fast changing currents in high current switching regulators place a significant dynamic load on the unregulated
power source. An input capacitor helps to provide additional current to the power supply as well as smooth out
input voltage variations.
Like the output capacitor, the key specifications for the input capacitor are RMS current rating and working
voltage. The RMS current flowing through the input capacitor is equal to one-half of the maximum dc load current
so the capacitor should be rated to handle this. Paralleling multiple capacitors proportionally increases the
current rating of the total capacitance. The voltage rating should also be selected to be 1.3 times the maximum
input voltage. Depending on the unregulated input power source, under light load conditions the maximum input
voltage could be significantly higher than normal operation and should be considered when selecting an input
capacitor.
The input capacitor should be placed very close to the input pin of the LM2673. Due to relative high current
operation with fast transient changes, the series inductance of input connecting wires or PCB traces can create
ringing signals at the input terminal which could possibly propagate to the output or other parts of the circuitry. It
may be necessary in some designs to add a small valued (0.1μF to 0.47μF) ceramic type capacitor in parallel
with the input capacitor to prevent or minimize any ringing.
CATCH DIODE
When the power switch in the LM2673 turns OFF, the current through the inductor continues to flow. The path for
this current is through the diode connected between the switch output and ground. This forward biased diode
clamps the switch output to a voltage less than ground. This negative voltage must be greater than −1V so a low
voltage drop (particularly at high current levels) Schottky diode is recommended. Total efficiency of the entire
power supply is significantly impacted by the power lost in the output catch diode. The average current through
the catch diode is dependent on the switch duty cycle (D) and is equal to the load current times (1-D). Use of a
diode rated for much higher current than is required by the actual application helps to minimize the voltage drop
and power loss in the diode.
During the switch ON time the diode will be reversed biased by the input voltage. The reverse voltage rating of
the diode should be at least 1.3 times greater than the maximum input voltage.
BOOST CAPACITOR
The boost capacitor creates a voltage used to overdrive the gate of the internal power MOSFET. This improves
efficiency by minimizing the on resistance of the switch and associated power loss. For all applications it is
recommended to use a 0.01μF/50V ceramic capacitor.
RADJ, ADJUSTABLE CURRENT LIMIT
A key feature of the LM2673 is the ability to control the peak switch current. Without this feature the peak switch
current would be internally set to 5A or higher to accommodate 3A load current designs. This requires that both
the inductor (which could saturate with excessively high currents) and the catch diode be able to safely handle
up to 5A which would be conducted under load fault conditions.
If an application only requires a load current of 2A or so the peak switch current can be set to a limit just over the
maximum load current with the addition of a single programming resistor. This allows the use of less powerful
and more cost effective inductors and diodes.
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: LM2673
LM2673
SNVS030N –APRIL 2000–REVISED APRIL 2013
www.ti.com
The peak switch current is equal to a factor of 37,125 divided by RADJ. A resistance of 8.2KΩ sets the current
limit to typically 4.5A. For predictable control of the current limit it is recommended to keep the peak switch
current greater than 1A. For lower current applications 500mA and 1A switching regulators, the LM2674 and
LM2672, are available.
When the power switch reaches the current limit threshold it is immediately turned OFF and the internal switching
frequency is reduced. This extends the OFF time of the switch to prevent a steady state high current condition.
As the switch current falls below the current limit threshold, the switch will turn back ON. If a load fault continues,
the switch will again exceed the threshold and switch back OFF. This will result in a low duty cycle pulsing of the
power switch to minimize the overall fault condition power dissipation.
Css SOFTSTART CAPACITOR
This optional capacitor controls the rate at which the LM2673 starts up at power on. The capacitor is charged
linearly by an internal current source. This voltage ramp gradually increases the duty cycle of the power switch
until it reaches the normal operating duty cycle defined primarily by the ratio of the output voltage to the input
voltage. The softstart turn-on time is programmable by the selection of Css.
The formula for selecting a softstart capacitor is:
where
•
•
•
•
•
•
ISST = Softstart Current, 3.7μA typical
tSS = Softstart time, from design requirements
VSST = Softstart Threshold Voltage, 0.63V typical
VOUT = Output Voltage, from design requirements
VSCHOTTKY = Schottky Diode Voltage Drop, typically 0.5V
VIN = Maximum Input Voltage, from design requirements
(1)
If this feature is not desired, leave the Softstart pin (pin 7) open circuited
With certain softstart capacitor values and operating conditions, the LM2673 can exhibit an overshoot on the
output voltage during turn on. Especially when starting up into no load or low load, the softstart function may not
be effective in preventing a larger voltage overshoot on the output. With larger loads or lower input voltages
during startup this effect is minimized. In particular, avoid using softstart capacitors between 0.033µF and 1µF.
ADDITIONAL APPLICATION INFORMATION
When the output voltage is greater than approximately 6V, and the duty cycle at minimum input voltage is greater
than approximately 50%, the designer should exercise caution in selection of the output filter components. When
an application designed to these specific operating conditions is subjected to a current limit fault condition, it may
be possible to observe a large hysteresis in the current limit. This can affect the output voltage of the device until
the load current is reduced sufficiently to allow the current limit protection circuit to reset itself.
Under current limiting conditions, the LM267x is designed to respond in the following manner:
1. At the moment when the inductor current reaches the current limit threshold, the ON-pulse is immediately
terminated. This happens for any application condition.
2. However, the current limit block is also designed to momentarily reduce the duty cycle to below 50% to avoid
subharmonic oscillations, which could cause the inductor to saturate.
3. Thereafter, once the inductor current falls below the current limit threshold, there is a small relaxation time
during which the duty cycle progressively rises back above 50% to the value required to achieve regulation.
If the output capacitance is sufficiently ‘large’, it may be possible that as the output tries to recover, the output
capacitor charging current is large enough to repeatedly re-trigger the current limit circuit before the output has
fully settled. This condition is exacerbated with higher output voltage settings because the energy requirement of
the output capacitor varies as the square of the output voltage (½CV2), thus requiring an increased charging
current.
12
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM2673
LM2673
www.ti.com
SNVS030N –APRIL 2000–REVISED APRIL 2013
A simple test to determine if this condition might exist for a suspect application is to apply a short circuit across
the output of the converter, and then remove the shorted output condition. In an application with properly
selected external components, the output will recover smoothly.
Practical values of external components that have been experimentally found to work well under these specific
operating conditions are COUT = 47µF, L = 22µH. It should be noted that even with these components, for a
device’s current limit of ICLIM, the maximum load current under which the possibility of the large current limit
hysteresis can be minimized is ICLIM/2. For example, if the input is 24V and the set output voltage is 18V, then for
a desired maximum current of 1.5A, the current limit of the chosen switcher must be confirmed to be at least 3A.
Under extreme over-current or short circuit conditions, the LM267X employs frequency foldback in addition to the
current limit. If the cycle-by-cycle inductor current increases above the current limit threshold (due to short circuit
or inductor saturation for example) the switching frequency will be automatically reduced to protect the IC.
Frequency below 100 KHz is typical for an extreme short circuit condition.
SIMPLE DESIGN PROCEDURE
Using the nomographs and tables in this data sheet (or use the available design software at www.ti.com) a
complete step-down regulator can be designed in a few simple steps.
Step 1: Define the power supply operating conditions:
Required output voltage
Maximum DC input voltage
Maximum output load current
Step 2: Set the output voltage by selecting a fixed output LM2673 (3.3V, 5V or 12V applications) or determine
the required feedback resistors for use with the adjustable LM2673−ADJ
Step 3: Determine the inductor required by using one of the four nomographs, Figure 18 through Figure 21.
Table 1 provides a specific manufacturer and part number for the inductor.
Step 4: Using Table 6 and Table 7 (fixed output voltage) or Table 12 and Table 13 (adjustable output voltage),
determine the output capacitance required for stable operation. Table 3 and Table 13 provide the specific
capacitor type from the manufacturer of choice.
Step 5: Determine an input capacitor from Table 6 and Table 9 for fixed output voltage applications. Use Table 3
or Table 4 to find the specific capacitor type. For adjustable output circuits select a capacitor from Table 3 or
Table 4 with a sufficient working voltage (WV) rating greater than Vin max, and an rms current rating greater than
one-half the maximum load current (2 or more capacitors in parallel may be required).
Step 6: Select a diode from Table 10. The current rating of the diode must be greater than I load max and the
Reverse Voltage rating must be greater than Vin max.
Step 7: Include a 0.01μF/50V capacitor for Cboost in the design and then determine the value of a softstart
capacitor if desired.
Step 8: Define a value for RADJ to set the peak switch current limit to be at least 20% greater than Iout max to
allow for at least 30% inductor ripple current (±15% of Iout). For designs that must operate over the full
temperature range the switch current limit should be set to at least 50% greater than Iout max (1.5 x Iout max).
FIXED OUTPUT VOLTAGE DESIGN EXAMPLE
A system logic power supply bus of 3.3V is to be generated from a wall adapter which provides an unregulated
DC voltage of 13V to 16V. The maximum load current is 2.5A. A softstart delay time of 50mS is desired.
Through-hole components are preferred.
Step 1: Operating conditions are:
Vout = 3.3V
Vin max = 16V
Iload max = 2.5A
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: LM2673
LM2673
SNVS030N –APRIL 2000–REVISED APRIL 2013
www.ti.com
Step 2: Select an LM2673T-3.3. The output voltage will have a tolerance of
±2% at room temperature and ±3% over the full operating temperature range.
Step 3: Use the nomograph for the 3.3V device, Figure 18. The intersection of the 16V horizontal line (Vin max)
and the 2.5A vertical line (Iload max) indicates that L33, a 22μH inductor, is required.
From Table 1, L33 in a through-hole component is available from Renco with part number RL-1283-22-43 or part
number PE-53933 from Pulse Engineering.
Step 4: Use Table 6 or Table 7 to determine an output capacitor. With a 3.3V output and a 33μH inductor there
are four through-hole output capacitor solutions with the number of same type capacitors to be paralleled and an
identifying capacitor code given. Table 3 or Table 4 provide the actual capacitor characteristics. Any of the
following choices will work in the circuit:
1 x 220μF/10V Sanyo OS-CON (code C5)
1 x 1000μF/35V Sanyo MV-GX (code C10)
1 x 2200μF/10V Nichicon PL (code C5)
1 x 1000μF/35V Panasonic HFQ (code C7)
Step 5: Use Table 6 or Table 9 to select an input capacitor. With 3.3V output and 22μH there are three through-
hole solutions. These capacitors provide a sufficient voltage rating and an rms current rating greater than 1.25A
(1/2 Iload max). Again using Table 3 or Table 4 for specific component characteristics the following choices are
suitable:
1 x 1000μF/63V Sanyo MV-GX (code C14)
1 x 820μF/63V Nichicon PL (code C24)
1 x 560μF/50V Panasonic HFQ (code C13)
Step 6: From Table 10 a 3A or more Schottky diode must be selected. The 20V rated diodes are sufficient for
the application and for through-hole components two part types are suitable:
1N5820
SR302
Step 7: A 0.01μF capacitor will be used for Cboost. For the 50mS softstart delay the following parameters are to
be used:
ISST: 3.7μA
tSS: 50mS
VSST: 0.63V
VOUT: 3.3V
VSCHOTTKY: 0.5V
VIN: 16V
Using Vin max ensures that the softstart delay time will be at least the desired 50mS.
Using the formula for Css a value of 0.148μF is determined to be required. Use of a standard value 0.22μF
capacitor will produce more than sufficient softstart delay.
Step 8: Determine a value for RADJ to provide a peak switch current limit of at least 2.5A plus 50% or 3.75A.
(2)
Use a value of 10KΩ.
14
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM2673
LM2673
www.ti.com
SNVS030N –APRIL 2000–REVISED APRIL 2013
ADJUSTABLE OUTPUT DESIGN EXAMPLE
In this example it is desired to convert the voltage from a two battery automotive power supply (voltage range of
20V to 28V, typical in large truck applications) to the 14.8VDC alternator supply typically used to power electronic
equipment from single battery 12V vehicle systems. The load current required is 2A maximum. It is also desired
to implement the power supply with all surface mount components. Softstart is not required.
Step 1: Operating conditions are:
Vout = 14.8V
Vin max = 28V
Iload max = 2A
Step 2: Select an LM2673S-ADJ. To set the output voltage to 14.9V two resistors need to be chosen (R1 and R2
in Figure 17). For the adjustable device the output voltage is set by the following relationship:
where
•
VFB is the feedback voltage of typically 1.21V
(3)
(4)
A recommended value to use for R1 is 1K. In this example then R2 is determined to be:
R2 = 11.23KΩ
The closest standard 1% tolerance value to use is 11.3KΩ
This will set the nominal output voltage to 14.88V which is within 0.5% of the target value.
Step 3: To use the nomograph for the adjustable device, Figure 21, requires a calculation of the inductor
Volt•microsecond constant (E•T expressed in V•μS) from the following formula:
where
•
VSAT is the voltage drop across the internal power switch which is Rds(ON) times Iload
(5)
In this example this would be typically 0.15Ω x 2A or 0.3V and VD is the voltage drop across the forward bisased
Schottky diode, typically 0.5V. The switching frequency of 260KHz is the nominal value to use to estimate the
ON time of the switch during which energy is stored in the inductor.
For this example E•T is found to be:
(6)
(7)
Using Figure 21, the intersection of 27V•μS horizontally and the 2A vertical line (Iload max) indicates that L38 , a
68μH inductor, should be used.
From Table 1, L38 in a surface mount component is available from Pulse Engineering with part number PE-
54038S.
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: LM2673
LM2673
SNVS030N –APRIL 2000–REVISED APRIL 2013
www.ti.com
Step 4: Use Table 12 or Table 13 to determine an output capacitor. With a 14.8V output the 12.5 to 15V row is
used and with a 68μH inductor there are three surface mount output capacitor solutions. Table 3 or Table 4
provide the actual capacitor characteristics based on the C Code number. Any of the following choices can be
used:
1 x 33μF/20V AVX TPS (code C6)
1 x 47μF/20V Sprague 594 (code C8)
1 x 47μF/20V Kemet T495 (code C8)
NOTE
When using the adjustable device in low voltage applications (less than 3V output), if the
nomograph, Figure 21, selects an inductance of 22μH or less, Table 12 and Table 13 do
not provide an output capacitor solution. With these conditions the number of output
capacitors required for stable operation becomes impractical. It is recommended to use
either a 33μH or 47μH inductor and the output capacitors from Table 12 or Table 13.
Step 5: An input capacitor for this example will require at least a 35V WV rating with an rms current rating of 1A
(1/2 Iout max). From Table 3 or Table 4 it can be seen that C12, a 33μF/35V capacitor from Sprague, has the
required voltage/current rating of the surface mount components.
Step 6: From Table 10 a 3A Schottky diode must be selected. For surface mount diodes with a margin of safety
on the voltage rating one of five diodes can be used:
SK34
30BQ040
30WQ04F
MBRS340
MBRD340
Step 7: A 0.01μF capacitor will be used for Cboost.
The softstart pin will be left open circuited.
Step 8: Determine a value for RADJ to provide a peak switch current limit of at least 2A plus 50% or 3A.
(8)
Use a value of 12.4KΩ.
VSON PACKAGE DEVICES
The LM2673 is offered in the 14 lead VSON surface mount package to allow for a significantly decreased
footprint with equivalent power dissipation compared to the DDPAK. For details on mounting and soldering
specifications,
refer
to
Application
Note
AN-1187
at
www.ti.com/lsds/ti/analog/powermanagement/power_portal.page.
16
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM2673
LM2673
www.ti.com
SNVS030N –APRIL 2000–REVISED APRIL 2013
Inductor Selection Guides
For Continuous Mode Operation
Figure 18. LM2673-3.3
Figure 19. LM2673-5.0
Figure 20. LM2673-12
Figure 21. LM2673-ADJ
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links: LM2673
LM2673
SNVS030N –APRIL 2000–REVISED APRIL 2013
www.ti.com
Table 1. Inductor Manufacturer Part Numbers
Inductor
Reference
Number
Renco
Pulse Engineering
Coilcraft
Inductance
(µH)
Current
(A)
Through Hole Surface Mount Through Hole Surface Mount Surface Mount
L23
L24
L25
L29
L30
L31
L32
L33
L34
L38
L39
L40
L41
L44
L45
33
22
15
100
68
47
33
22
15
68
47
33
22
68
10
1.35
1.65
2.00
1.41
1.71
2.06
2.46
3.02
3.65
2.97
3.57
4.26
5.22
3.45
4.47
RL-5471-7
RL-1283-22-43
RL-1283-15-43
RL-5471-4
RL1500-33
RL1500-22
RL1500-15
PE-53823
PE-53824
PE-53825
PE-53823S
PE-53824S
PE-53825S
PE-53829S
PE-53830S
PE-53831S
PE-53932S
PE-53933S
PE-53934S
PE-54038S
PE-54039S
PE-54040S
P0841
DO3316-333
DO3316-223
DO3316-153
DO5022P-104
DO5022P-683
DO5022P-473
DO5022P-333
DO5022P-223
DO5022P-153
—
RL-6050-100 PE-53829
RL-5471-5
RL6050-68
PE-53830
PE-53831
PE-53932
PE-53933
PE-53934
PE-54038
PE-54039
PE-54040
PE-54041
PE-54044
—
RL-5471-6
RL6050-47
RL-5471-7
RL6050-33
RL-1283-22-43
RL-1283-15-43
RL-5472-2
RL6050-22
—
—
—
—
—
—
—
RL-5472-3
—
RL-1283-33-43
RL-1283-22-43
RL-5473-3
—
—
—
—
RL-1283-10-43
P0845
DO5022P-103HC
Table 2. Inductor Manufacturer Contact Numbers
Coilcraft
Phone
FAX
(800) 322-2645
(708) 639-1469
+44 1236 730 595
+44 1236 730 627
(619) 674-8100
(619) 674-8262
+353 93 24 107
+353 93 24 459
(800) 645-5828
(516) 586-5562
Coilcraft, Europe
Pulse Engineering
Pulse Engineering, Europe
Renco Electronics
Phone
FAX
Phone
FAX
Phone
FAX
Phone
FAX
18
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM2673
LM2673
www.ti.com
SNVS030N –APRIL 2000–REVISED APRIL 2013
Capacitor Selection Guides
Table 3. Input and Output Capacitor Codes—Surface Mount
Surface Mount
Capacitor
Reference Code
AVX TPS Series
Sprague 594D Series
Kemet T495 Series
C (µF)
330
100
220
47
WV (V)
6.3
10
Irms (A)
1.15
1.1
C (µF)
WV (V)
6.3
6.3
10
Irms (A)
C (µF)
100
220
330
100
150
220
33
WV (V)
6.3
6.3
6.3
10
Irms (A)
C1
C2
120
220
68
1.1
1.4
0.82
1.1
C3
10
1.15
0.89
1.15
0.77
0.94
0.77
0.63
0.66
1.05
1.35
1
1.1
C4
16
150
47
10
1.1
C5
100
33
16
16
10
1.1
C6
20
100
180
47
16
1.3
10
1.1
C7
68
20
16
1.95
1.15
1.05
1.6
20
0.78
0.94
0.94
0.63
0.63
0.66
C8
22
25
20
47
20
C9
10
35
33
25
68
20
C10
C11
C12
C13
22
35
68
25
10
35
15
35
0.75
1
22
35
33
35
4.7
50
15
50
0.9
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Links: LM2673
LM2673
SNVS030N –APRIL 2000–REVISED APRIL 2013
www.ti.com
Table 4. Input and Output Capacitor Codes—Through Hole
Through Hole
Sanyo MV-GX Series Nichicon PL Series
Capacitor
Reference
Code
Sanyo OS-CON SA Series
Panasonic HFQ Series
C (µF)
WV (V)
Irms
(A)
C (µF)
WV (V)
Irms
(A)
C (µF)
WV (V)
Irms
(A)
C (µF)
WV (V)
Irms
(A)
C1
C2
47
6.3
6.3
6.3
10
10
16
16
16
20
25
1
1000
270
470
560
820
1000
150
470
680
1000
220
470
680
1000
6.3
16
16
16
16
16
35
35
35
35
63
63
63
63
0.8
0.6
680
820
10
10
10
10
10
10
10
10
16
16
16
16
16
16
25
35
35
35
50
50
50
63
63
63
63
0.8
82
120
220
330
560
820
1000
2200
56
35
35
35
35
35
35
35
35
50
50
50
50
50
50
63
63
0.4
0.44
0.76
1.01
1.4
150
330
100
220
33
1.95
2.45
1.87
2.36
0.96
1.92
2.28
2.25
2.09
0.98
1.06
1.28
1.71
2.18
2.36
2.68
0.41
0.55
0.77
1.02
1.22
1.88
0.63
0.79
1.43
2.68
0.82
1.04
1.3
C3
0.75
0.95
1.25
1.3
1000
1200
2200
3300
3900
6800
180
C4
C5
C6
1.62
1.73
2.8
C7
100
150
100
47
0.65
1.3
C8
C9
1.4
0.36
0.5
C10
C11
C12
C13
C14
C15
C16
C17
C18
C19
C20
C21
C22
C23
C24
C25
1.7
270
100
220
470
560
1200
330
1500
0.76
1.2
470
0.92
1.44
1.68
2.22
1.42
2.51
680
1.5
820
1.75
1800
220
220
560
2200
150
220
330
100
0.75
1.62
2.22
2.51
390
820
1200
Table 5. Capacitor Manufacturer Contact Numbers
Nichicon
Panasonic
AVX
Phone
FAX
(847) 843-7500
(847) 843-2798
(714) 373-7857
(714) 373-7102
(845) 448-9411
(845) 448-1943
(207) 324-4140
(207) 324-7223
(619) 661-6322
(619) 661-1055
(864) 963-6300
(864) 963-6521
Phone
FAX
Phone
FAX
Sprague/Vishay
Sanyo
Phone
FAX
Phone
FAX
Kemet
Phone
FAX
20
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM2673
LM2673
www.ti.com
SNVS030N –APRIL 2000–REVISED APRIL 2013
Table 6. Output Capacitors for Fixed Output Voltage Application—Surface Mount(1)(2)
Surface Mount
Output Voltage
(V)
Inductance (µH)
AVX TPS Series
Sprague 594D Series
Kemet T495 Series
No.
C Code
C2
No.
3
C Code
C1
No.
4
C Code
10
15
22
33
10
15
22
33
47
10
15
22
33
47
68
100
4
4
3
2
4
3
3
2
2
4
3
2
2
2
1
1
C4
C4
C4
C4
C4
C4
C4
C4
C4
C9
C8
C8
C8
C8
C7
C8
C2
3
C1
4
3.3
C2
2
C7
3
C2
2
C6
2
C2
4
C6
4
C2
2
C7
3
5
C2
2
C7
3
C2
2
C3
2
C2
1
C7
2
C5
3
C6
5
C5
2
C7
4
C5
2
C6
3
12
C5
1
C7
2
C4
1
C6
2
C5
1
C5
2
C4
1
C5
1
(1) No. represents the number of identical capacitor types to be connected in parallel
(2) C Code indicates the Capacitor Reference number in Table 3 and Table 4 for identifying the specific component from the manufacturer.
Table 7. Output Capacitors for Fixed Output Voltage Application—Through Hole(1)(2)
Through Hole
Output
Voltage (V)
Inductance
(µH)
Sanyo OS-CON SA
Series
Sanyo MV-GX Series
Nichicon PL Series
Panasonic HFQ Series
No.
1
C Code
C3
No.
1
C Code
C10
C10
C10
C10
C10
C10
C5
No.
1
C Code
C6
No.
2
C Code
C6
10
15
22
33
10
15
22
33
47
10
15
22
33
47
68
100
1
C3
1
1
C6
2
C5
3.3
1
C5
1
1
C5
1
C7
1
C2
1
1
C13
C6
1
C5
2
C4
1
1
2
C5
1
C5
1
1
C5
1
C6
5
1
C5
1
1
C5
1
C5
1
C4
1
C5
1
C13
C13
C18
C17
C13
C11
C10
C10
C9
1
C5
1
C4
1
C4
1
2
C3
2
C7
2
C5
1
2
C5
1
C8
1
C5
1
1
C5
1
C7
1
C5
1
1
C5
12
1
C7
1
C3
1
1
C4
1
C7
1
C3
1
1
C3
1
C7
1
C2
1
1
C3
1
C7
1
C2
1
1
C1
(1) No. represents the number of identical capacitor types to be connected in parallel
(2) C Code indicates the Capacitor Reference number in Table 3 and Table 4 for identifying the specific component from the manufacturer.
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
21
Product Folder Links: LM2673
LM2673
SNVS030N –APRIL 2000–REVISED APRIL 2013
www.ti.com
Table 8. Input Capacitors for Fixed Output Voltage Application—Surface Mount(1)(2)(3)
Surface Mount
Output Voltage
(V)
Inductance (µH)
AVX TPS Series
Sprague 594D Series
Kemet T495 Series
No.
C Code
C5
No.
1
C Code
C7
No.
2
C Code
C8
10
15
22
33
10
15
22
33
47
10
15
22
33
47
68
100
2
3
See(4)
See(4)
2
C9
1
C10
C13
C13
C7
3
C10
C12
C12
C8
3.3
See(4)
See(4)
C5
2
3
2
2
1
2
2
C5
1
C7
2
C8
5
3
C10
2
C12
C13
C13
C10
C10
C12
C12
C13
C13
C13
3
C11
C12
C12
C7
See(4)
See(4)
2
See(4)
See(4)
C7
2
3
1
2
2
2
2
C7
2
2
C7
3
C10
2
3
C10
C10
C12
C12
C12
12
3
C10
2
3
See(4)
See(4)
See(4)
See(4)
See(4)
See(4)
2
3
2
2
1
2
(1) Assumes worst case maximum input voltage and load current for a given inductance value
(2) No. represents the number of identical capacitor types to be connected in parallel
(3) C Code indicates the Capacitor Reference number in Table 3 and Table 4 for identifying the specific component from the manufacturer.
(4) Check voltage rating of capacitors to be greater than application input voltage.
Table 9. Input Capacitors for Fixed Output Voltage Application—Through Hole(1)(2)(3)
Through Hole
Output
Voltage (V)
Inductance
(µH)
Sanyo OS-CON SA
Series
Sanyo MV-GX Series
Nichicon PL Series
Panasonic HFQ Series
No.
1
C Code
C7
No.
2
C Code
C4
No.
1
C Code
C5
No.
1
C Code
C6
10
15
22
33
10
15
22
33
47
10
15
22
33
47
68
100
1
C10
1
C10
C14
C12
C4
1
C18
C24
C20
C14
C14
C18
C23
C20
C18
C18
C18
C18
C23
C21
C22
1
C6
3.3
See(4)
See(4)
1
See(4)
See(4)
C7
1
1
1
C13
C12
C6
1
1
1
2
1
1
1
C7
2
C4
1
1
C6
5
See(4)
See(4)
See(4)
1
See(4)
See(4)
See(4)
C9
1
C10
C14
C12
C10
C10
C10
C10
C13
C12
C11
1
1
C13
C13
C12
C6
1
1
1
1
1
1
1
1
1
1
C10
1
1
1
C6
1
C10
1
1
1
C6
12
See(4)
See(4)
See(4)
See(4)
See(4)
See(4)
See(4)
See(4)
1
1
1
C6
1
1
1
C13
C12
C11
1
1
1
1
1
1
(1) Assumes worst case maximum input voltage and load current for a given inductance value
(2) No. represents the number of identical capacitor types to be connected in parallel
(3) C Code indicates the Capacitor Reference number in Table 3 and Table 4 for identifying the specific component from the manufacturer.
(4) Check voltage rating of capacitors to be greater than application input voltage.
22
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM2673
LM2673
www.ti.com
SNVS030N –APRIL 2000–REVISED APRIL 2013
Table 10. Schottky Diode Selection Table
Reverse
Voltage (V)
Surface Mount
5A or More
Through Hole
5A or More
3A
3A
20V
30V
40V
SK32
1N5820
SR302
SK33
MBRD835L
1N5821
31DQ03
1N5822
MBR340
31DQ04
SR403
30WQ03F
SK34
MBRB1545CT
6TQ045S
30BQ040
30WQ04F
MBRS340
MBRD340
SK35
MBR745
80SQ045
6TQ045
50V or More
MBR350
31DQ05
SR305
30WQ05F
Table 11. Diode Manufacturer Contact Numbers
International Rectifier
Phone
FAX
(310) 322-3331
(310) 322-3332
(800) 521-6274
(602) 244-6609
(516) 847-3000
(516) 847-3236
(805) 446-4800
(805) 446-4850
Motorola
Phone
FAX
General Semiconductor
Diodes, Inc.
Phone
FAX
Phone
FAX
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
23
Product Folder Links: LM2673
LM2673
SNVS030N –APRIL 2000–REVISED APRIL 2013
www.ti.com
Table 12. Output Capacitors for Adjustable Output Voltage Applications—Surface Mount(1)(2)
Surface Mount
Output Voltage (V)
Inductance (µH)
AVX TPS Series
No. C Code
Sprague 594D Series
Kemet T495 Series
No.
6
4
3
2
3
2
2
3
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
4
3
2
1
1
1
C Code
C2
No.
7
5
4
3
4
3
2
3
2
2
1
3
2
1
1
2
2
1
1
2
2
1
1
1
1
1
1
2
2
2
1
2
1
1
1
8
5
4
3
2
2
C Code
C3
33(3)
47(3)
33(3)
47(3)
22
7
5
4
3
4
3
2
3
2
2
1
3
2
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
C1
C1
C1
C1
C1
C1
C1
C2
C2
C2
C2
C2
C2
C3
C2
C5
C5
C5
C4
C5
C5
C5
C5
C6
C6
C6
C6
C8
C8
C8
C8
C9
C10
C9
C9
1.21 to 2.50
2.5 to 3.75
C2
C3
C2
C3
C2
C3
C2
C3
3.75 to 5
5 to 6.25
33
C2
C3
47
C2
C3
22
C3
C4
33
C3
C4
47
C3
C4
68
C3
C4
22
C4
C4
33
C3
C4
6.25 to 7.5
7.5 to 10
10 to 12.5
12.5 to 15
15 to 20
47
C4
C6
68
C3
C4
33
C6
C8
47
C6
C8
68
C6
C8
100
33
C5
C8
C6
C8
47
C6
C8
68
C6
C8
100
33
C6
C8
C8
C8
47
C8
C8
68
C8
C8
100
33
C8
C8
C10
C9
C10
C10
C10
C10
C11
C11
C11
C11
C12
C12
C12
C12
C12
C12
47
68
C9
100
33
C9
C11
C12
C12
C12
C13
C13
C13
C13
C13
C13
47
20 to 30
68
100
10
15
22
30 to 37
No Values Available
33
47
68
(1) No. represents the number of identical capacitor types to be connected in parallel
(2) C Code indicates the Capacitor Reference number in Table 3 and Table 4 for identifying the specific component from the manufacturer.
(3) Set to a higher value for a practical design solution. See Application Hints section
24
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM2673
LM2673
www.ti.com
SNVS030N –APRIL 2000–REVISED APRIL 2013
Table 13. Output Capacitors for Adjustable Output Voltage Applications—Through Hole(1)(2)
Through Hole
Inductance
(µH)
Sanyo OS-CON SA
Series
Output Voltage (V)
Sanyo MV-GX Series
Nichicon PL Series
Panasonic HFQ Series
No.
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
C Code
C3
No.
5
4
3
2
3
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
C Code
C1
No.
5
3
3
2
3
2
1
2
2
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
C Code
C3
No.
3
2
2
1
2
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
C Code
C
33(3)
47(3)
33(3)
47(3)
22
1.21 to 2.50
2.5 to 3.75
C2
C1
C3
C5
C5
C5
C5
C5
C5
C5
C5
C5
C5
C5
C5
C5
C5
C5
C5
C2
C2
C5
C5
C2
C2
C2
C2
C2
C2
C2
C2
C2
C2
C2
C2
C2
C2
C10
C11
C10
C10
C10
C10
C3
C1
C1
C2
C1
C3
C3
C1
C1
3.75 to 5
5 to 6.25
33
C2
C1
C1
47
C2
C1
C3
22
C5
C6
C3
33
C4
C6
C1
47
C4
C6
C3
68
C4
C6
C1
22
C5
C6
C1
33
C4
C6
C3
6.25 to 7.5
7.5 to 10
10 to 12.5
12.5 to 15
15 to 20
47
C4
C6
C1
68
C4
C2
C1
33
C7
C6
C14
C14
C14
C14
C14
C14
C9
47
C7
C6
68
C7
C2
100
33
C7
C2
C7
C6
47
C7
C2
68
C7
C2
100
33
C7
C2
C9
C9
C10
C10
C10
C10
C7
C15
C15
C15
C15
C15
C15
C15
C15
C16
C16
C16
C16
C20
C20
C20
C20
C20
C20
47
C9
68
C9
100
33
C9
C10
C10
C10
C10
47
C7
68
C7
100
33
C7
C7
47
C7
20 to 30
No Values Available
68
C7
100
10
C7
C12
C11
C11
C11
C11
C11
15
22
30 to 37
No Values Available
33
47
68
(1) No. represents the number of identical capacitor types to be connected in parallel
(2) C Code indicates the Capacitor Reference number in Table 3 and Table 4 for identifying the specific component from the manufacturer.
(3) Set to a higher value for a practical design solution. See Application Hints section
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
25
Product Folder Links: LM2673
LM2673
SNVS030N –APRIL 2000–REVISED APRIL 2013
www.ti.com
REVISION HISTORY
Changes from Revision M (April 2013) to Revision N
Page
•
Changed layout of National Data Sheet to TI format .......................................................................................................... 25
26
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM2673
PACKAGE OPTION ADDENDUM
www.ti.com
1-Nov-2013
PACKAGING INFORMATION
Orderable Device
LM2673S-12
Status Package Type Package Pins Package
Eco Plan
Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
Device Marking
Samples
Drawing
Qty
(1)
(2)
(6)
(3)
(4/5)
NRND
DDPAK/
TO-263
KTW
7
7
45
TBD
Call TI
CU SN
Call TI
CU SN
Call TI
CU SN
Call TI
CU SN
CU SN
CU SN
CU SN
CU SN
CU SN
CU SN
CU SN
CU SN
CU SN
Call TI
LM2673
S-12
LM2673S-12/NOPB
LM2673S-3.3
ACTIVE
NRND
DDPAK/
TO-263
KTW
KTW
KTW
KTW
KTW
KTW
KTW
NHM
NHM
NHM
NHM
NHM
NHM
NHM
KTW
KTW
45
45
Pb-Free (RoHS
Exempt)
Level-3-245C-168 HR
Call TI
LM2673
S-12
DDPAK/
TO-263
7
TBD
LM2673
S-3.3
LM2673S-3.3/NOPB
LM2673S-5.0
ACTIVE
NRND
DDPAK/
TO-263
7
45
Pb-Free (RoHS
Exempt)
Level-3-245C-168 HR
Call TI
LM2673
S-3.3
DDPAK/
TO-263
7
45
TBD
LM2673
S-5.0
LM2673S-5.0/NOPB
LM2673S-ADJ
ACTIVE
NRND
DDPAK/
TO-263
7
45
Pb-Free (RoHS
Exempt)
Level-3-245C-168 HR
Call TI
LM2673
S-5.0
DDPAK/
TO-263
7
45
TBD
LM2673
S-ADJ
LM2673S-ADJ/NOPB
LM2673SD-12/NOPB
LM2673SD-3.3/NOPB
LM2673SD-5.0/NOPB
LM2673SD-ADJ/NOPB
LM2673SDX-3.3/NOPB
LM2673SDX-5.0/NOPB
LM2673SDX-ADJ/NOPB
LM2673SX-12/NOPB
LM2673SX-3.3/NOPB
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
DDPAK/
TO-263
7
45
Pb-Free (RoHS
Exempt)
Level-3-245C-168 HR
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-3-245C-168 HR
Level-3-245C-168 HR
LM2673
S-ADJ
VSON
VSON
VSON
VSON
VSON
VSON
VSON
14
14
14
14
14
14
14
7
250
250
250
250
2500
2500
2500
500
500
Green (RoHS
& no Sb/Br)
S0002SB
S0002TB
S0002UB
S0002VB
S0002TB
S0002UB
S0002VB
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
DDPAK/
TO-263
Pb-Free (RoHS
Exempt)
LM2673
S-12
DDPAK/
TO-263
7
Pb-Free (RoHS
Exempt)
LM2673
S-3.3
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
1-Nov-2013
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
Device Marking
Samples
Drawing
Qty
(1)
(2)
(6)
(3)
(4/5)
LM2673SX-5.0
LM2673SX-5.0/NOPB
LM2673SX-ADJ
NRND
DDPAK/
TO-263
KTW
7
7
7
7
7
7
7
7
7
7
500
TBD
Call TI
CU SN
Call TI
CU SN
CU SN
CU SN
Call TI
CU SN
Call TI
CU SN
Call TI
Level-3-245C-168 HR
Call TI
LM2673
S-5.0
ACTIVE
NRND
DDPAK/
TO-263
KTW
KTW
KTW
NDZ
NDZ
NDZ
NDZ
NDZ
NDZ
500
500
500
45
Pb-Free (RoHS
Exempt)
LM2673
S-5.0
DDPAK/
TO-263
TBD
LM2673
S-ADJ
LM2673SX-ADJ/NOPB
LM2673T-12/NOPB
LM2673T-3.3/NOPB
LM2673T-5.0
ACTIVE
ACTIVE
ACTIVE
NRND
DDPAK/
TO-263
Pb-Free (RoHS
Exempt)
Level-3-245C-168 HR
Level-1-NA-UNLIM
Level-1-NA-UNLIM
Call TI
LM2673
S-ADJ
TO-220
TO-220
TO-220
TO-220
TO-220
TO-220
Green (RoHS
& no Sb/Br)
LM2673
T-12
45
Green (RoHS
& no Sb/Br)
LM2673
T-3.3
45
TBD
LM2673
T-5.0
LM2673T-5.0/NOPB
LM2673T-ADJ
ACTIVE
NRND
45
Green (RoHS
& no Sb/Br)
Level-1-NA-UNLIM
Call TI
LM2673
T-5.0
45
TBD
LM2673
T-ADJ
LM2673T-ADJ/NOPB
ACTIVE
45
Green (RoHS
& no Sb/Br)
Level-1-NA-UNLIM
LM2673
T-ADJ
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
1-Nov-2013
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Oct-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LM2673SD-12/NOPB
LM2673SD-3.3/NOPB
LM2673SD-5.0/NOPB
LM2673SD-ADJ/NOPB
LM2673SDX-3.3/NOPB
LM2673SDX-5.0/NOPB
VSON
VSON
VSON
VSON
VSON
VSON
NHM
NHM
NHM
NHM
NHM
NHM
NHM
KTW
14
14
14
14
14
14
14
7
250
250
178.0
178.0
178.0
178.0
330.0
330.0
330.0
330.0
16.4
16.4
16.4
16.4
16.4
16.4
16.4
24.4
5.3
5.3
5.3
5.3
5.3
5.3
5.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
1.5
1.5
1.5
1.5
1.5
1.5
1.5
5.0
12.0
12.0
12.0
12.0
12.0
12.0
12.0
16.0
16.0
16.0
16.0
16.0
16.0
16.0
16.0
24.0
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q2
250
250
2500
2500
2500
500
LM2673SDX-ADJ/NOPB VSON
LM2673SX-12/NOPB
LM2673SX-3.3/NOPB
LM2673SX-5.0
DDPAK/
TO-263
10.75 14.85
10.75 14.85
10.75 14.85
10.75 14.85
10.75 14.85
10.75 14.85
DDPAK/
TO-263
KTW
KTW
KTW
KTW
KTW
7
7
7
7
7
500
500
500
500
500
330.0
330.0
330.0
330.0
330.0
24.4
24.4
24.4
24.4
24.4
5.0
5.0
5.0
5.0
5.0
16.0
16.0
16.0
16.0
16.0
24.0
24.0
24.0
24.0
24.0
Q2
Q2
Q2
Q2
Q2
DDPAK/
TO-263
LM2673SX-5.0/NOPB
LM2673SX-ADJ
DDPAK/
TO-263
DDPAK/
TO-263
LM2673SX-ADJ/NOPB DDPAK/
TO-263
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Oct-2013
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
LM2673SD-12/NOPB
LM2673SD-3.3/NOPB
LM2673SD-5.0/NOPB
LM2673SD-ADJ/NOPB
LM2673SDX-3.3/NOPB
LM2673SDX-5.0/NOPB
LM2673SDX-ADJ/NOPB
LM2673SX-12/NOPB
LM2673SX-3.3/NOPB
LM2673SX-5.0
VSON
VSON
NHM
NHM
NHM
NHM
NHM
NHM
NHM
KTW
KTW
KTW
KTW
KTW
KTW
14
14
14
14
14
14
14
7
250
250
250
250
2500
2500
2500
500
500
500
500
500
500
210.0
210.0
210.0
210.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
185.0
185.0
185.0
185.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
45.0
45.0
45.0
45.0
45.0
45.0
VSON
VSON
VSON
VSON
VSON
DDPAK/TO-263
DDPAK/TO-263
DDPAK/TO-263
DDPAK/TO-263
DDPAK/TO-263
DDPAK/TO-263
7
7
LM2673SX-5.0/NOPB
LM2673SX-ADJ
7
7
LM2673SX-ADJ/NOPB
7
Pack Materials-Page 2
MECHANICAL DATA
NDZ0007B
TA07B (Rev E)
www.ti.com
MECHANICAL DATA
NHM0014A
SRC14A (Rev A)
www.ti.com
MECHANICAL DATA
KTW0007B
TS7B (Rev E)
BOTTOM SIDE OF PACKAGE
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
相关型号:
LM2673SX-12/NOPB
8V to 40V, 3A SIMPLE SWITCHER® buck converter with adjustable current limit 7-DDPAK/TO-263 -40 to 125
TI
LM2673SX-12/NOPB
IC 5.4 A SWITCHING REGULATOR, 280 kHz SWITCHING FREQ-MAX, PSSO7, POWER, TO-263, SMT-7, Switching Regulator or Controller
NSC
LM2673SX-5.0/NOPB
8V to 40V, 3A SIMPLE SWITCHER® buck converter with adjustable current limit 7-DDPAK/TO-263 -40 to 125
TI
©2020 ICPDF网 联系我们和版权申明