LM2681_15 概述
LM2681 Switched Capacitor Voltage Converter
LM2681_15 数据手册
通过下载LM2681_15数据手册来全面了解它。这个PDF文档包含了所有必要的细节,如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载LM2681
www.ti.com
SNVS042B –MARCH 1999–REVISED MAY 2013
LM2681 Switched Capacitor Voltage Converter
Check for Samples: LM2681
1
FEATURES
DESCRIPTION
The LM2681 CMOS charge-pump voltage converter
operates as a voltage doubler for an input voltage in
the range of +2.5V to +5.5V. Two low cost capacitors
and a diode (needed during start-up) is used in this
circuit to provide up to 20 mA of output current. The
LM2681 can also work as a voltage divider to split a
voltage in the range of +1.8V to +11V in half.
2
•
•
•
•
Doubles or Splits Input Supply Voltage
SOT-23 6-Lead Package
15Ω Typical Output Impedance
90% Typical Conversion Efficiency at 20 mA
APPLICATIONS
The LM2681 operates at 160 kHz oscillator frequency
to reduce output resistance and voltage ripple. With
an operating current of only 550 µA (operating
efficiency greater than 90% with most loads) the
LM2681 provides ideal performance for battery
powered systems. The device is in a SOT-23, 6-lead
package.
•
•
•
•
•
•
Cellular Phones
Pagers
PDAs
Operational Amplifier Power Suppliers
Interface Power Suppliers
Handheld Instruments
Basic Application Circuits
Voltage Doubler
Splitting Vin in Half
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
2
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 1999–2013, Texas Instruments Incorporated
LM2681
SNVS042B –MARCH 1999–REVISED MAY 2013
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings(1)(2)
V+ to GND Voltage
5.8V
11.6V
OUT to GND Voltage
OUT to V+ Voltage
5.8V
V+ and OUT Continuous Output Current
Output Short-Circuit Duration to GND(3)
Continuous Power Dissipation (TA = 25°C)(4)
30 mA
1 sec.
600 mW
150°C
(4)
TJMax
(4)
θJA
210°C/W
−40° to 85°C
−65°C to +150°C
300°C
Operating Junction Temperature Range
Storage Temperature Range
Lead Temp. (Soldering, 10 seconds)
ESD Rating
2kV
(1) Absolute maximum ratings indicate limits beyond which damage to the device may occur. Electrical specifications do not apply when
operating the device beyond its rated operating conditions.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
(3) OUT may be shorted to GND for one second without damage. However, shorting OUT to V+ may damage the device and should be
avoided. Also, for temperatures above 85°C, OUT must not be shorted to GND or V+, or device may be damaged.
(4) The maximum allowable power dissipation is calculated by using PDMax = (TJMax − TA)/θJA, where TJMax is the maximum junction
temperature, TA is the ambient temperature, and θJA is the junction-to-ambient thermal resistance of the specified package.
Electrical Characteristics
Limits in standard typeface are for TJ = 25°C, and limits in boldface type apply over the full operating temperature range.
Unless otherwise specified: V+ = 5V, C1 = C2 = 3.3 μF.(1)
Symbol
Parameter
Supply Voltage
Condition
Min
2.5
Typ
Max
5.5
Units
V
V+
IQ
IL
Supply Current
Output Current
No Load
550
1000
µA
20
mA
RSW
Sum of the Rds(on)of the four internal
MOSFET switches
IL = 20 mA
8
16
40
Ω
ROUT
fOSC
fSW
Output Resistance(2)
Oscillator Frequency
Switching Frequency
Power Efficiency
IL = 20 mA
See(3)
See(3)
15
160
80
Ω
80
40
86
kHz
kHz
PEFF
RL (1.0k) between GND and OUT
IL = 20 mA to GND
No Load
93
%
%
90
VOEFF
Voltage Conversion Efficiency
99
99.96
(1) In the test circuit, capacitors C1 and C2 are 3.3 µF, 0.3Ω maximum ESR capacitors. Capacitors with higher ESR will increase output
resistance, reduce output voltage and efficiency.
(2) Specified output resistance includes internal switch resistance and capacitor ESR. See POSITIVE VOLTAGE DOUBLER
(3) The output switches operate at one half of the oscillator frequency, fOSC = 2fSW
.
2
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM2681
LM2681
www.ti.com
SNVS042B –MARCH 1999–REVISED MAY 2013
Test Circuit
Figure 1. LM2681 Test Circuit
Copyright © 1999–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LM2681
LM2681
SNVS042B –MARCH 1999–REVISED MAY 2013
www.ti.com
Typical Performance Characteristics
(Circuit of Figure 1, V+ = 5V unless otherwise specified)
Supply Current vs
Supply Voltage
Supply Current vs
Temperature
Figure 2.
Figure 3.
Output Source
Resistance
vs
Output Source
Resistance
vs
Supply
Voltage
Temperature
Figure 4.
Figure 5.
Efficiency
vs
Load Current
Output Voltage Drop
vs Load Current
Figure 6.
Figure 7.
4
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM2681
LM2681
www.ti.com
SNVS042B –MARCH 1999–REVISED MAY 2013
Typical Performance Characteristics (continued)
(Circuit of Figure 1, V+ = 5V unless otherwise specified)
Oscillator Frequency vs
Oscillator Frequency vs
Temperature
Supply Voltage
Figure 8.
Figure 9.
Copyright © 1999–2013, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: LM2681
LM2681
SNVS042B –MARCH 1999–REVISED MAY 2013
www.ti.com
CONNECTION DIAGRAM
Figure 10. SOT-23, 6-Lead Package – Top View
See Package Number DBV
Figure 11. Actual Size
PIN DESCRIPTION
Function
Pin
Name
Voltage Doubler
Voltage Split
Positive voltage output
Same as doubler
1
2
3
V+
Power supply positive voltage input
Power supply ground input
GND
CAP−
Connect this pin to the negative terminal of the charge-
pump capacitor
Same as doubler
4
5
6
GND
OUT
Power supply ground input
Positive voltage output
Same as doubler
Power supply positive voltage input
CAP+
Connect this pin to the positive terminal of the charge-pump Same as doubler
capacitor
Circuit Description
The LM2681 contains four large CMOS switches which are switched in a sequence to double the input supply
voltage. Energy transfer and storage are provided by external capacitors. Figure 12 illustrates the voltage
conversion scheme. When S2 and S4 are closed, C1 charges to the supply voltage V+. During this time interval,
switches S1 and S3 are open. In the next time interval, S2 and S4 are open; at the same time, S1 and S3 are
closed, the sum of the input voltage V+ and the voltage across C1 gives the 2V+ output voltage when there is no
load. The output voltage drop when a load is added is determined by the parasitic resistance (Rds(on) of the
MOSFET switches and the ESR of the capacitors) and the charge transfer loss between capacitors. Details will
be discussed in the APPLICATION INFORMATION section.
Figure 12. Voltage Doubling Principle
6
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM2681
LM2681
www.ti.com
SNVS042B –MARCH 1999–REVISED MAY 2013
APPLICATION INFORMATION
POSITIVE VOLTAGE DOUBLER
The main application of the LM2681 is to double the input voltage. The range of the input supply voltage is 2.5V
to 5.5V.
The output characteristics of this circuit can be approximated by an ideal voltage source in series with a
resistance. The voltage source equals 2V+. The output resistance Rout is a function of the ON resistance of the
internal MOSFET switches, the oscillator frequency, the capacitance and ESR of C1 and C2. Since the switching
current charging and discharging C1 is approximately twice as the output current, the effect of the ESR of the
pumping capacitor C1 will be multiplied by four in the output resistance. The output capacitor C2 is charging and
discharging at a current approximately equal to the output current, therefore, its ESR only counts once in the
output resistance. A good approximation of Rout is:
(1)
where RSW is the sum of the ON resistance of the internal MOSFET switches shown in Figure 12.
The peak-to-peak output voltage ripple is determined by the oscillator frequency, the capacitance and ESR of the
output capacitor C2:
(2)
High capacitance, low ESR capacitors can reduce both the output reslistance and the voltage ripple.
The Schottky diode D1 is only needed for start-up. The internal oscillator circuit uses the OUT pin and the GND
pin. Voltage across OUT and GND must be larger than 1.8V to insure the operation of the oscillator. During start-
up, D1 is used to charge up the voltage at the OUT pin to start the oscillator; also, it protects the device from
turning-on its own parasitic diode and potentially latching-up. Therefore, the Schottky diode D1 should have
enough current carrying capability to charge the output capacitor at start-up, as well as a low forward voltage to
prevent the internal parasitic diode from turning-on. A Schottky diode like 1N5817 can be used for most
applications. If the input voltage ramp is less than 10V/ms, a smaller Schottky diode like MBR0520LT1 can be
used to reduce the circuit size.
SPLIT V+ IN HALF
Another interesting application shown in the Basic Application Circuits is using the LM2681 as a precision voltage
divider. . This circuit can be derived from the voltage doubler by switching the input and output connections. In
the voltage divider, the input voltage applies across the OUT pin and the GND pin (which are the power rails for
the internal oscillator), therefore no start-up diode is needed. Also, since the off-voltage across each switch
equals Vin/2, the input voltage can be raised to +11V.
CAPACITOR SELECTION
As discussed in the POSITIVE VOLTAGE DOUBLER section, the output resistance and ripple voltage are
dependent on the capacitance and ESR values of the external capacitors. The output voltage drop is the load
current times the output resistance, and the power efficiency is
(3)
2
Where IQ(V+) is the quiescent power loss of the IC device, and IL Rout is the conversion loss associated with the
switch on-resistance, the two external capacitors and their ESRs.
The selection of capacitors is based on the specifications of the dropout voltage (which equals Iout Rout), the
output voltage ripple, and the converter efficiency. Low ESR capacitors are recommended to maximize efficiency,
reduce the output voltage drop and voltage ripple.
Copyright © 1999–2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: LM2681
LM2681
SNVS042B –MARCH 1999–REVISED MAY 2013
www.ti.com
Low ESR Capacitor Manufacturers
Manufacturer
Phone
Capacitor Type
PL & PF series, through-hole aluminum electrolytic
TPS series, surface-mount tantalum
593D, 594D, 595D series, surface-mount tantalum
OS-CON series, through-hole aluminum electrolytic
Ceramic chip capacitors
Nichicon Corp.
AVX Corp.
Sprague
(708)-843-7500
(803)-448-9411
(207)-324-4140
(619)-661-6835
(800)-831-9172
(800)-348-2496
(408)-432-8020
Sanyo
Murata
Taiyo Yuden
Tokin
Ceramic chip capacitors
Ceramic chip capacitors
Other Applications
PARALLELING DEVICES
Any number of LM2681s can be paralleled to reduce the output resistance. Each device must have its own
pumping capacitor C1, while only one output capacitor Cout is needed as shown in Figure 13. The composite
output resistance is:
(4)
Figure 13. Lowering Output Resistance by Paralleling Devices
CASCADING DEVICES
Cascading the LM2681s is an easy way to produce a greater voltage (A two-stage cascade circuit is shown in
Figure 14).
The effective output resistance is equal to the weighted sum of each individual device:
Rout = 1.5Rout_1 + Rout_2
(5)
Note that, the increasing of the number of cascading stages is practically limited since it significantly reduces the
efficiency, increases the output resistance and output voltage ripple.
Figure 14. Increasing Output Voltage by Cascading Devices
8
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM2681
LM2681
www.ti.com
SNVS042B –MARCH 1999–REVISED MAY 2013
REGULATING VOUT
It is possible to regulate the output of the LM2681 by use of a low dropout regulator (such as LP2980-5.0). The
whole converter is depicted in Figure 15.
A different output voltage is possible by use of LP2980-3.3, LP2980-3.0, or LP2980-adj.
Note that, the following conditions must be satisfied simultaneously for worst case design:
2Vin_min >Vout_min +Vdrop_max (LP2980) + Iout_max × Rout_max (LM2681)
2Vin_max < Vout_max +Vdrop_min (LP2980) + Iout_min × Rout_min (LM2681)
(6)
(7)
Figure 15. Generate a Regulated +5V from +3V Input Voltage
Copyright © 1999–2013, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: LM2681
LM2681
SNVS042B –MARCH 1999–REVISED MAY 2013
www.ti.com
REVISION HISTORY
Changes from Revision A (May 2013) to Revision B
Page
•
Changed layout of National Data Sheet to TI format ............................................................................................................ 9
10
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM2681
PACKAGE OPTION ADDENDUM
www.ti.com
1-Nov-2013
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(6)
(3)
(4/5)
LM2681M6/NOPB
ACTIVE
SOT-23
DBV
6
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 85
S10A
LM2681M6X
NRND
SOT-23
SOT-23
DBV
DBV
6
6
3000
3000
TBD
Call TI
CU SN
Call TI
-40 to 85
-40 to 85
S10A
S10A
LM2681M6X/NOPB
ACTIVE
Green (RoHS
& no Sb/Br)
Level-1-260C-UNLIM
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
1-Nov-2013
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LM2681M6/NOPB
LM2681M6X
SOT-23
SOT-23
SOT-23
DBV
DBV
DBV
6
6
6
1000
3000
3000
178.0
178.0
178.0
8.4
8.4
8.4
3.2
3.2
3.2
3.2
3.2
3.2
1.4
1.4
1.4
4.0
4.0
4.0
8.0
8.0
8.0
Q3
Q3
Q3
LM2681M6X/NOPB
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
LM2681M6/NOPB
LM2681M6X
SOT-23
SOT-23
SOT-23
DBV
DBV
DBV
6
6
6
1000
3000
3000
210.0
210.0
210.0
185.0
185.0
185.0
35.0
35.0
35.0
LM2681M6X/NOPB
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
LM2681_15 相关器件
型号 | 制造商 | 描述 | 价格 | 文档 |
LM2682 | NSC | Switched Capacitor Voltage Doubling Inverter | 获取价格 | |
LM2682 | TI | LM2682 Switched Capacitor Voltage Doubling Inverter | 获取价格 | |
LM2682M | NSC | Switched Capacitor Voltage Doubling Inverter | 获取价格 | |
LM2682M/NOPB | ROCHESTER | SWITCHED CAPACITOR CONVERTER, 15kHz SWITCHING FREQ-MAX, PDSO8, 0.150 INCH, SOIC-8 | 获取价格 | |
LM2682M/NOPB | TI | IC SWITCHED CAPACITOR CONVERTER, 15 kHz SWITCHING FREQ-MAX, PDSO8, 0.150 INCH, SOIC-8, Switching Regulator or Controller | 获取价格 | |
LM2682MDC | NSC | IC SWITCHED CAPACITOR CONVERTER, 15 kHz SWITCHING FREQ-MAX, UUC, DIE, Switching Regulator or Controller | 获取价格 | |
LM2682MM | NSC | Switched Capacitor Voltage Doubling Inverter | 获取价格 | |
LM2682MM/NOPB | NSC | IC SWITCHED CAPACITOR CONVERTER, 15 kHz SWITCHING FREQ-MAX, PDSO8, MINI, MSOP-8, Switching Regulator or Controller | 获取价格 | |
LM2682MM/NOPB | TI | LM2682 Switched Capacitor Voltage Doubling Inverter | 获取价格 | |
LM2682MMX | NSC | Switched Capacitor Voltage Doubling Inverter | 获取价格 |
LM2681_15 相关文章
- 2024-09-20
- 6
- 2024-09-20
- 9
- 2024-09-20
- 8
- 2024-09-20
- 6