LM2751SD-B [TI]
LM2751 Regulated 2X, 1.5X Switched Capacitor White LED Driver; LM2751稳压2X , 1.5X开关电容白光LED驱动器![LM2751SD-B](http://pdffile.icpdf.com/pdf1/p00187/img/icpdf/LM2751_1055117_icpdf.jpg)
型号: | LM2751SD-B |
厂家: | ![]() |
描述: | LM2751 Regulated 2X, 1.5X Switched Capacitor White LED Driver |
文件: | 总19页 (文件大小:1385K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
![](http://public.icpdf.com/style/img/ads.jpg)
LM2751
www.ti.com
SNVS299B –APRIL 2005–REVISED MAY 2013
LM2751 Regulated 2X, 1.5X Switched Capacitor White LED Driver
Check for Samples: LM2751
1
FEATURES
APPLICATIONS
2
•
•
•
•
Regulated Output Options: 4.5V, 5.0V
Output Voltage Regulated Within 3%
Peak Efficiency Over 90%
•
•
•
White LED Display Backlights
White LED Keypad Backlights
General Purpose 2×, 1.5× Regulated Charge
Pump
150mA (4.5V) or 80mA (5.0V) Output Current
Capability
DESCRIPTION
The LM2751 is
capacitor charge pump with regulated output voltage
options of 4.5V, and 5.0V. Over the input voltage
range of 2.8V to 5.5V the LM2751 provides up to
150mA of output current and requires only four low-
cost ceramic capacitors.
•
•
•
•
•
Input Voltage Range: 2.8V to 5.5V
Low Input and Output Voltage Ripple
<1µA Typical Shutdown Current
Small Solution Size - NO INDUCTOR
a constant frequency switched
Programmable 725kHz, 300kHz, 37kHz, or
9.5kHz Switching Frequencies
•
10-pin SON No-Pullback Package: 3mm × 3mm
× 0.8mm
Typical Application Circuit
V
= 2.8V - 5.5V
V
OUT
= 4.5V, or 5.0V
IN
V
V
OUT
IN
3
2
1
C1+
2.2 µF
2.2 µF
C
OUT
C
IN
D
D
X
1
1 µF
C
1
R
R
9
C -
1
LM2751
EN
6
4
5
8
C +
2
10
CS0
CS1
GND
1 µF
C
2
7
C -
2
Capacitors: 1 µF - TDK C1608X7R1A105K
2.2 µF - TDK C2012X5R1A225K
LM2751 2x/1.5x Efficiency vs.
2x Charge Pump Efficiency
100
LM2751 2x, 1.5x Pump
V
= 4.5V
OUT
V
= 5.0V
OUT
90
80
70
60
V
= 5.0V
OUT
V
= 4.5V
OUT
Typical 2x Only Pump
50
40
2.7
3.0
3.3
3.6
3.9
4.2
INPUT VOLTAGE (V)
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
2
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2005–2013, Texas Instruments Incorporated
LM2751
SNVS299B –APRIL 2005–REVISED MAY 2013
www.ti.com
DESCRIPTION (CONTINUED)
The LM2751 provides excellent efficiency without the use of an inductor by operating the charge pump in a gain
of 3/2 or 2. The proper gain for maintaining regulation is chosen so that efficiency is maximized over the input
voltage range.
LM2751 uses constant frequency pre-regulation to minimize conducted noise on the input and provide a
predictable switching frequency. The switching frequency is programmable to 725kHz, 300kHz, 37kHz, or
9.5kHz.
LM2751 is available in a 10-pin SON No-Pullback Package.
Connection Diagram
1
2
3
4
5
10
9
C2+
C1-
GND
C2-
EN
C2+
C1-
10
9
1
2
3
4
5
V
V
OUT
OUT
C1+
C1+
8
GND
C2-
8
V
V
IN
IN
CS0
CS1
7
7
CS0
CS1
6
EN
6
Die-Attach Pad: GND
Die-Attach Pad: GND
Top View
Bottom View
Figure 1. 10-pin SON No Pullback Package (3mm × 3mm × 0.8mm)
See Package Number DSC0010A
PIN DESCRIPTIONS
Pin #
Name
VOUT
C1+
Description
1
2
Pre-Regulated Output.
Flying Capacitor C1 Connection.
Input Supply Range: 2.8V to 5.5V.
Frequency Select Input 0.
Frequency Select Input 1.
Enable Pin Logic Input.
3
VIN
4
CS0
CS1
EN
5
6
7
C2−
Flying Capacitor C2 Connection.
Ground.
8
GND
C1−
9
Flying Capacitor C1 Connection.
Flying Capacitor C2 Connection.
10
C2+
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
2
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM2751
LM2751
www.ti.com
SNVS299B –APRIL 2005–REVISED MAY 2013
ABSOLUTE MAXIMUM RATINGS(1)(2)(3)
VIN Pin
−0.3V to 6.0V
EN, CS0, CS1 Pins
−0.3V to (VIN+0.3)
w/ 6.0V max
Continuous Power Dissipation(4)
Internally Limited
150°C
Junction Temperature (TJ-MAX-ABS
Storage Temperature Range
Maximum Lead Temperature
)
−65°C to 150°C
265°C
(Soldering, 10sec.)
ESD Rating(5)
Human-body model
Machine model
2kV
200V
(1) Absolute Maximum Ratings indicate limits beyond which damage to the component may occur. Operating Ratings are conditions under
which operation of the device is specified. Operating Ratings do not imply ensured performance limits. For specified performance limits
and associated test conditions, see the Electrical Characteristics tables.
(2) All voltages are with respect to the potential at the GND pin.
(3) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
(4) Internal thermal shutdown circuitry protects the device from permanent damage. Thermal shutdown engages at TJ=150°C (typ.) and
disengages at TJ=140°C (typ.).
(5) The Human body model is a 100 pF capacitor discharged through a 1.5kΩ resistor into each pin. The machine model is a 200pF
capacitor discharged directly into each pin (MIL-STD-883 3015.7).
OPERATING RATINGS(1)(2)
Input Voltage Range
2.8V to 5.5V
0V to VIN
EN, CS0, CS1 Input Voltage Range
Junction Temperature (TJ) Range
Ambient Temperature (TA) Range(3)
Recommended Maximum Load Current
-40°C to 115°C
-40°C to 85°C
Version B
Freq. = 725kHz
Freq. = 300kHz
Freq. = 37kHz
Freq. = 9.5kHz
Freq. = 725kHz
Freq. = 300kHz
Freq. = 37kHz
Freq. = 9.5kHz
150mA
120mA
40mA
10mA
80mA
60mA
16mA
4mA
Version A
(1) Absolute Maximum Ratings indicate limits beyond which damage to the component may occur. Operating Ratings are conditions under
which operation of the device is specified. Operating Ratings do not imply ensured performance limits. For specified performance limits
and associated test conditions, see the Electrical Characteristics tables.
(2) All voltages are with respect to the potential at the GND pin.
(3) In applications where high power dissipation and/or poor package thermal resistance is present, the maximum ambient temperature may
have to be derated. Maximum ambient temperature (TA-MAX) is dependent on the maximum operation junction temperature (TJ-MAX-OP
115ºC), the maximum power dissipation of the device in the application (PD-MAX), and the junction-to ambient thermal resistance of the
part/package in the application (θJA), as given by the following equation:
=
TA-MAX = TJ-MAX-OP - (θJA × PD-MAX).
THERMAL PROPERTIES
Junction-to-Ambient Thermal
Resistance, 10-pin SON
(1)
Package (θJA)
55°C/W
(1) Junction-to-ambient thermal resistance (θJA) is taken from a thermal modeling result, performed under the conditions and guidelines set
forth in the JEDEC standard JESD51-7. The test board is a 4 layer FR-4 board measuring 102mm x 76mm x 1.6mm with a 2 x 1 array
of thermal vias. The ground plane on the board is 50mm x 50mm. Thickness of copper layers are 36µm/18µm
/18µm/36µm(1.5oz/1oz/1oz/1.5oz). Ambient temperature in simulation is 22ºC, still air. Power dissipation is 1W. The value of θJA of the
LM2751 in 10-pin SON could fall in a range as wide as 50ºC/W to 150ºC/W (if not wider), depending on PWB material, layout, and
environmental conditions. In applications where high maximum power dissipation exists (high VIN, high IOUT), special care must be paid
to thermal dissipation issues. For more information on these topics, see the TI AN-1187 Application Report (SNOA401) and the Power
Efficiency and Power Dissipation section of this datasheet.
Copyright © 2005–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LM2751
LM2751
SNVS299B –APRIL 2005–REVISED MAY 2013
www.ti.com
ELECTRICAL CHARACTERISTICS(1)(2)
Limits in standard typeface are for TA = 25ºC. Limits in boldface type apply over the full operating ambient temperature range
(-40°C ≤ TA ≤ +85°C) . Unless otherwise noted, specifications apply to the LM2751 Typical Application Circuit (pg. 1) with: VIN
(3)
= 3.6V, V(EN) = VIN, CS0 = CS1 = VIN, C1 = C2 = 1.0µF, CIN = COUT = 2.2µF
.
Symbol
Parameter
Output Voltage
Conditions
Min
Typ
Max
Units
VOUT
Version A, 2.8V ≤ VIN ≤ 5.5V,
Freq. = 300kHz, 725kHz, TA = 25°C
IOUT = 0 to 60mA
4.850
(-3%)
5.0
5.150
(+3%)
V
Version A, 2.8V ≤ VIN ≤ 5.5V,
4.775
5.225
Freq. = 300kHz, IOUT = 0 to 60mA
Freq. = 725kHz, IOUT = 0 to 80mA
(-4.5%)
(+4.5%)
Version B, 2.8V ≤ VIN ≤ 5.5V,
Freq. = 300kHz, 725kHz, TA = 25°C
IOUT = 0 to 120mA
4.343
(-3.5%)
4.5
4.658
(+3.5%)
Version B, 2.8V ≤ VIN ≤ 5.5V,
Freq. = 300kHz, IOUT = 0 to 120mA
Freq. = 725kHz, IOUT = 0 to 150mA
4.275
(-5%)
4.725
(+5%)
VR
IQ
Output Ripple
2.8V ≤ VIN ≤ 5.5V
IOUT = 60mA
8
mV
µA
Quiescent Current
Freq. = 9.5kHz, IOUT = 0mA, VIN = 3.7V
Freq. = 37kHz, IOUT = 0mA, VIN = 3.7V
Freq. = 300kHz, IOUT = 0mA, VIN = 3.7V
Freq. = 725kHz, IOUT = 0mA, VIN = 3.7V
425
450
700
1000
0.77
1.0
600
640
900
1500
1.3
ISD
Shutdown Supply Current V(EN) = 0V
V(EN) = 0V, TA = 85°C
µA
%
E
Efficiency
IOUT = 80mA (Version A, 5.0V)
Freq. = 300kHz, 725kHz
92
IOUT = 150mA (Version B, 4.5V)
Freq. = 300kHz, 725kHz
83
9.5
37
fSW
Switching Frequency
CS0 = High, CS1 = Low
2.8V ≤ VIN ≤ 5.5V
6.7
(−30%)
12.3
kHz
(+30%)
CS0 = Low, CS1 = Low
26
48
2.8V ≤ VIN ≤ 5.5V
(−30%)
(+30%)
CS0 = Low, CS1 = High
2.8V ≤ VIN ≤ 5.5V
210
(−30%)
300
725
390
(+30%)
CS0 = High, CS1 = High
508
942
2.8V ≤ VIN ≤ 5.5V
(−30%)
(+30%)
VIH
VIL
IIH
Logic Input High
Input Pins: EN, CS0, CS1
2.8V ≤ VIN ≤ 5.5V
1.00
VIN
V
V
Logic Input Low
Input Pins: EN, CS0, CS1
2.8V ≤ VIN ≤ 5.5V
0
.30
Logic Input High Current
Input Pins: CS0, CS1
V(CSx) = 1.8V
10
2
nA
µA
nA
V
Input Pin: EN
V(EN) = 1.8V(4)
IIL
Logic Input Low Current
Input Pins: EN, CS0, CS1
V(EN, CSx) = 0V
10
VG
Gain Transition Voltage
(Version A, B)
1.5X to 2X
2X to 1.5X
3.50
3.58
Hysteresis
VOUT = 0V
40
80
150
mV
mA
ISC
Short Circuit Output
Current
250
(1) All voltages are with respect to the potential at the GND pin.
(2) Min and Max limits are specified by design, test, or statistical analysis. Typical numbers are not ensured, but represent the most likely
norm.
(3) CIN, COUT, C1, and C2: Low-ESR Surface-Mount Ceramic Capacitors (MLCCs) used in setting electrical characteristics.
(4) EN Logic Input High Current (IIH) is due to a 1MΩ(typ.) pull-down resistor connected internally between the EN pin and GND.
4
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM2751
LM2751
www.ti.com
SNVS299B –APRIL 2005–REVISED MAY 2013
ELECTRICAL CHARACTERISTICS(1)(2) (continued)
Limits in standard typeface are for TA = 25ºC. Limits in boldface type apply over the full operating ambient temperature range
(-40°C ≤ TA ≤ +85°C) . Unless otherwise noted, specifications apply to the LM2751 Typical Application Circuit (pg. 1) with: VIN
= 3.6V, V(EN) = VIN, CS0 = CS1 = VIN, C1 = C2 = 1.0µF, CIN = COUT = 2.2µF (3)
.
Symbol
Parameter
Conditions
Min
Typ
Max
Units
tON
VOUT Turn-On Time(5)
300
µs
(5) Turn-on time is measured from when the EN signal is pulled high until the output voltage on VOUT crosses 90% of its final value.
Copyright © 2005–2013, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: LM2751
LM2751
SNVS299B –APRIL 2005–REVISED MAY 2013
www.ti.com
BLOCK DIAGRAM
LM2751
V
IN
C1+
GAIN
CONTROL
SWITCH
CONTROL
SWITCH
ARRAY
1.2V Ref.
C1-
CS0
CS1
3
2
C2+
G = 2 ,
FREQ. CTRL
C2-
V
OUT
OSC
Short-Circuit
Protection
Divider
(Div 16,
Div 8)
Thermal Shutdown
OSCILLATOR
EN
Enable /
Shutdown
Control
EN
1.2V
Ref.
Soft-Start
Ramp
GND
6
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM2751
LM2751
www.ti.com
SNVS299B –APRIL 2005–REVISED MAY 2013
TYPICAL PERFORMANCE CHARACTERISTICS
Unless otherwise specified: TA = 25°C, VIN = 3.6V, CS0 = CS1 = VIN, V(EN) = VIN, CIN = COUT = 2.2µF, C1 = C2 = 1µF.
Output Voltage
Output Voltage
vs.
vs.
Output Current, Version A (5V), 300kHz
Output Current, Version B (4.5V), 300kHz
4.60
5.10
5.08
4.58
V
= 4.2V
IN
V
IN
= 5.5V
V
IN
= 5.5V
V
IN
= 4.2V
4.56
4.54
4.52
4.50
V
= 3.3V
IN
V
= 2.8V
IN
5.05
5.03
V
IN
= 3.6V
V
= 3.6V
30
IN
V
IN
= 3.3V
V
= 2.8V
IN
5.00
0
13 26 39 52 65 78 91 104 117 130
OUTPUT CURRENT (mA)
Figure 3.
0
10
20
40
50
60
70
OUTPUT CURRENT (mA)
Figure 2.
Output Voltage
vs.
Output Current, Version A (5V), 725kHz
Output Voltage
vs.
Output Current, Version B (4.5V), 725kHz
4.60
5.08
5.06
5.03
5.01
4.98
4.57
V
= 5.5V
V
IN
V
= 5.5V
V
IN
= 4.2V
= 4.2V
IN
IN
4.54
4.51
4.48
4.45
V
IN
= 3.3V
V
= 3.6V
IN
V
= 2.8V
IN
V
IN
= 3.6V
V
= 2.8V
V
IN
= 3.3V
IN
0
15
30
45
60
75
90
0
20 40 60 80 100 120 140 160
OUTPUT CURRENT (mA)
OUTPUT CURRENT (mA)
Figure 4.
Figure 5.
Input Current
vs.
Input Voltage, Version A (5V)
Input Current
vs.
Input Voltage, Version B (4.5V)
1.70
1.50
1.30
1.10
0.90
0.70
0.50
1.5
1.3
1.1
0.9
0.7
0.5
F
= 725 kHz
F
= 725 kHz
SW
SW
I
= 0
I
= 0
OUT
OUT
T
= 25°C
T
= 25°C
A
A
F
= 300 kHz
SW
F
= 300 kHz
SW
2.7 3.1 3.5 3.9 4.3 4.7 5.1 5.5
2.7 3.1 3.5 3.9 4.3 4.7 5.1 5.5
INPUT VOLTAGE (V)
INPUT VOLTAGE (V)
Figure 6.
Figure 7.
Copyright © 2005–2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: LM2751
LM2751
SNVS299B –APRIL 2005–REVISED MAY 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Unless otherwise specified: TA = 25°C, VIN = 3.6V, CS0 = CS1 = VIN, V(EN) = VIN, CIN = COUT = 2.2µF, C1 = C2 = 1µF.
Output Voltage
Output Voltage
vs.
vs.
Input Voltage, Version A (5V), 300kHz
Input Voltage, Version B (4.5V), 300kHz
5.09
4.63
I
= 0 mA
OUT
4.60
4.57
4.54
4.51
4.48
5.07
I
= 0 mA
OUT
I
= 20 mA
OUT
OUT
5.04
5.02
I
= 40 mA
OUT
I
= 60 mA
I
= 120 mA
OUT
I
= 70 mA
OUT
I
= 80 mA
OUT
4.99
2.7 3.1 3.5 3.9 4.3 4.7 5.1 5.5
2.7 3.1 3.5 3.9 4.3 4.7 5.1 5.5
INPUT VOLTAGE (V)
INPUT VOLTAGE (V)
Figure 8.
Figure 9.
Output Voltage
vs.
Output Voltage
vs.
Input Voltage, Version A (5V), 725kHz
Input Voltage, Version B (4.5V), 725kHz
5.09
4.60
4.57
4.54
4.51
4.48
4.45
I
= 0 mA
OUT
I
= 0 mA
OUT
5.06
I
= 40 mA
OUT
I
= 20 mA
OUT
5.03
5.00
4.97
I
= 120 mA
OUT
I
= 80 mA
= 60 mA
OUT
I
= 152 mA
OUT
I
OUT
2.7 3.1 3.5 3.9 4.3 4.7 5.1 5.5
2.7 3.1 3.5 3.9 4.3 4.7 5.1 5.5
INPUT VOLTAGE (V)
INPUT VOLTAGE (V)
Figure 10.
Figure 11.
Efficiency
vs.
Input Voltage, Version A (5V)
Efficiency
vs.
Input Voltage, Version B (4.5V)
100
90
80
70
60
50
40
100
90
80
70
60
50
40
2.7 3.1 3.5 3.9 4.3 4.7 5.1 5.5
2.7 3.1 3.5 3.9 4.3 4.7 5.1 5.5
INPUT VOLTAGE (V)
INPUT VOLTAGE (V)
Figure 12.
Figure 13.
8
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM2751
LM2751
www.ti.com
SNVS299B –APRIL 2005–REVISED MAY 2013
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Unless otherwise specified: TA = 25°C, VIN = 3.6V, CS0 = CS1 = VIN, V(EN) = VIN, CIN = COUT = 2.2µF, C1 = C2 = 1µF.
Output Voltage Ripple
vs. Input Voltage Version B (4.5V), Load = 120mA
Output Voltage Ripple, Version B (4.5V)
22
C
IN
= 1.0 F
COUT: 2.2
F
Capacitance,
300 kHz
18
13
9
COUT: 2.2
Capacitance,
725 kHz
F
COUT: 10
F
Capacitance,
300 kHz
COUT: 10
F
Capacitance,
725 kHz
4
0
VIN = 3.6V, Load = 150mA
2.7 3.1 3.5 3.9 4.3 4.7 5.1 5.5
CH1: VOUT; Scale: 10mV/Div, AC Coupled
INPUT VOLTAGE (V)
Time scale: 400ns/Div
Figure 14.
Figure 15.
Line Step Response, Version B (4.5V)
Load Step Response, Version B (4.5V)
VIN = 3.2V - 4.2V Step, Load = 150mA
CH1 (top): VIN; Scale: 1V/Div, DC Coupled
CH2: VOUT; Scale: 50mV/Div, AC Coupled
VIN = 3.6V, Load = 20mA - 150mA Step
CH1 (top): VOUT; Scale: 50mV/Div, AC Coupled
CH2: Output Current; Scale: 50mA/Div
Time scale: 200µs/Div
Time scale: 200µs/Div
Figure 16.
Figure 17.
Start-up Behavior, Version A (5V), Load = 80mA
Start-up Behavior, Version B (4.5V), Load = 150mA
CH1: EN pin; Scale: 2V/Div
CH2: VOUT; Scale: 2V/Div
CH1: EN pin; Scale: 2V/Div
CH2: VOUT; Scale: 2V/Div
Time scale: 100µs/Div
Time scale: 100µs/Div
Figure 18.
Figure 19.
Copyright © 2005–2013, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: LM2751
LM2751
SNVS299B –APRIL 2005–REVISED MAY 2013
www.ti.com
APPLICATION INFORMATION
CIRCUIT DESCRIPTION
The LM2751 is a Switched Capacitor Convertor with gains of 2x and 1.5x. It is capable of continuously supplying
up to 150mA at 4.5V or up to 80mA at 5V depending on the output voltage option. The LM2751's fixed frequency
pre-regulation maintains the output voltage to within 3% (typ.), making it well suited for driving White LEDs.
There are also four user programmable switching frequencies to reduce the quiescent current consumption at
light loads.
Aside from powering LEDs, the LM2751 is suitable for driving other devices with power requirements up to
150mA. The LM2751 operates over the extended Li-Ion battery range from 2.8V to 5.5V. The LM2751 limits
output current to 250mA (typ.) during an output short circuit condition. LED brightness is controlled by applying a
PWM (Pulse Width Modulation) signal to the Enable pin (EN). See PWM BRIGHTNESS CONTROL.
SOFT START
Soft Start is engaged when the device is taken out of Shutdown mode (EN = logic HIGH) or when voltage is
supplied simultaneously to the VIN and EN pins. During Soft Start, the voltage on VOUT will ramp up in proportion
to the rate that the reference voltage is being ramped up. The output voltage is programmed to rise from 0V to
the regulated output voltage level (4.5V or 5V) in 300µs (typ.).
ENABLE MODE
The Enable logic pin (EN) disables the part and reduces the quiescent current to 0.77µA (typ.). The LM2751 has
an active-high enable pin (LOW = shut down, HIGH = operating) which can be driven with a low-voltage CMOS
logic signal (1.5V logic, 1.8V logic, etc). There is an internal 1MΩ pull-down resistor between the EN and GND
pins of the LM2751.
FREQUENCY MODE SELECT
The LM2751 switching frequency is user programmable via two logic input pins, CS0 and CS1. Both logic input
pins have active-high logic (LOW = un-selected, HIGH = selected) and can be driven with a low-voltage CMOS
logic signal (1.5V logic, 1.8V logic, etc). There are no internal pull-down or pull-up resistors between the CSx and
GND pins of the LM2751. The CSO and CS1 can be controlled independently or with the same logic signal.
The selectable switching frequencies are 9.5kHz, 37kHz, 300kHz, 725kHz. The switching frequency is
programmed according to Table 1.
Table 1. Frequency Modes
CS0
CS1
Frequency
37kHz
0
0
1
1
0
1
0
1
300kHz
9.5kHz
725kHz
VOUT REGULATION
The LM2751 uses pre-regulation to regulate the output voltage to 4.5V or 5.0V depending on the voltage option.
Pre-regulation uses the voltage present at VOUT to limit the gate drive of the switched capacitor charge pump.
This regulation is done before the voltage is gained up by the charge pump, giving rise to the term "pre-
regulation". Pre-regulation helps to reduce input current noise and large input current spikes normally associated
with switched capacitor charge pumps.
The LM2751 switched capacitor charge pump has gains of 2x and 1.5x. When the input voltage to the device is
greater than 3.58V (typ.), the LM2751 operates in a gain of 1.5x. When the input voltage falls below 3.5V (typ.),
the device switches to a gain of 2x.
10
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM2751
LM2751
www.ti.com
SNVS299B –APRIL 2005–REVISED MAY 2013
OUTPUT VOLTAGE RIPPLE
The primary contributor in keeping the output voltage ripple of the LM2751 low is its switching topology. The
output capacitance, input voltage, switching frequency and output current also play a significant part in
determining the output voltage ripple. Due to the complexity of the LM2751 operation, providing equations or
models to approximate the magnitude of the ripple cannot be easily accomplished. However, the following
general statements can be made.
The LM2751 has very low output ripple when compared to typical boost regulators due to its double-pump
topology, where charge is continually supplied to the output during both 2x and 1.5x modes. Combined with fixed
frequency operation modes, double-pumping allows for the use of a very small, low value ceramic capacitor on
the output node while still achieving minimal output ripple. Increasing the capacitance by adding a higher value
capacitor or placing multiple capacitors in parallel can further reduce the ripple magnitude.
CAPACITOR SELECTION
The LM2751 requires 4 external capacitors for proper operation. Surface-mount multi-layer ceramic capacitors
are recommended. These capacitors are small, inexpensive and have very low equivalent series resistance
(ESR, ≤15mΩ typ.). Tantalum capacitors, OS-CON capacitors, and aluminum electrolytic capacitors are generally
not recommended for use with the LM2751 due to their high ESR, as compared to ceramic capacitors.
For most applications, ceramic capacitors with X7R or X5R temperature characteristic are preferred for use with
the LM2751. These capacitors have tight capacitance tolerance (as good as ±10%), hold their value over
temperature (X7R: ±15% over −55°C to 125°C; X5R: ±15% over −55°C to 85°C), and typically have little voltage
coefficient when compared to other types of capacitors. However selecting a capacitor with a voltage rating much
higher than the voltage it will be subjected to, will ensure that the capacitance will stay closer to the capacitor's
nominal value. Capacitors with Y5V or Z5U temperature characteristic are generally not recommended for use
with the LM2751. Capacitors with these temperature characteristics typically have wide capacitance tolerance
(+80%, −20%), vary significantly over temperature (Y5V: +22%, −82% over −30°C to +85°C range; Z5U: +22%,
−56% over +10°C to +85°C range), and have poor voltage coefficients. Under some conditions, a nominal 1µF
Y5V or Z5U capacitor could have a capacitance of only 0.1µF. Such detrimental deviation is likely to cause Y5V
and Z5U capacitors to fail to meet the minimum capacitance requirements of the LM2751.
The voltage rating of the output capacitor should be 10V or more. All other capacitors should have a voltage
rating at or above the maximum input voltage of the application.
DRIVING WHITE LEDS
The desired LED current is set by placing a resistor (R) in series with each LED, and is determined by the
equation:
ILED = (VOUT - VLED) ÷R
(1)
In the equation above, ILED is the current that flows through a particular LED, and VLED is the forward voltage of
the LED at the given current. The output voltage (VOUT) of the LM2751 is tightly regulated to 4.5V or 5V
depending on the output voltage option. However, LED forward voltage varies from LED to LED, and LED current
will vary accordingly. Mismatch of LED currents will result in brightness mismatch from one LED to the next.
Therefore it is suggested that LED groups with tightly controlled I-V characteristics ("Binned" LEDs) be used.
LEDs with looser tolerance can be used in applications where brightness matching is not critical, such as in
keypad or general backlighting. The typical and maximum diode forward voltage depends highly on the
manufacturer and their technology.
PWM BRIGHTNESS CONTROL
Perceived LED brightness can be adjusted using a PWM control signal on the Enable pin of the LM2751, to turn
the voltage output ON and OFF at a rate faster than perceptible by the eye. When this is done, the total
brightness perceived is proportional to the duty cycle (D) of the PWM signal (D = the percentage of time that the
LED is on in every PWM cycle). A simple example: if the LEDs are driven at 15mA each with a PWM signal that
has a 50% duty cycle, perceived LED brightness will be about half as bright as compared to when the LEDs are
driven continuously with 15mA.
Copyright © 2005–2013, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: LM2751
LM2751
SNVS299B –APRIL 2005–REVISED MAY 2013
www.ti.com
For linear brightness control over the full duty cycle adjustment range, the PWM frequency (f) should be limited
to accommodate the turn-on time (typ. TON = 300µs) of the device.
D × (1/f) > TON
(2)
(3)
fMAX = DMIN ÷ TON
The minimum recommended PWM frequency is 100Hz. Frequencies below this may be visibly noticeable as
flicker or blinking. The maximum recommended PWM frequency is 1kHz. Frequencies above this may cause
noise in the audible range.
THERMAL PROTECTION
When the junction temperature exceeds 150°C (typ.), internal thermal protection circuitry disables the device.
This feature protects the LM2751 from damage due to excessive power dissipation. The device will recover and
operate normally when the junction temperature falls below 140°C (typ.). It is important to have good thermal
conduction with a proper layout to reduce thermal resistance.
POWER EFFICIENCY
Charge-Pump efficiency is derived in the following two ideal equations (supply current and other losses are
neglected for simplicity):
IIN = G x IOUT
(4)
(5)
E = (VOUT x IOUT) ÷ (VIN x IIN) = VOUT ÷ (G x VIN)
In the equations, G represents the charge pump gain. Efficiency is at its highest as G x VIN approaches VOUT
Refer to the efficiency graph in the Typical Performance Characteristics for the detailed efficiency data.
.
POWER DISSIPATION
The power dissipation (PDISSIPATION) and junction temperature (TJ) can be approximated with the equations
below. PIN is the product of the input current and input voltage, POUT is the power consumed by the load
connected to the output, TAis the ambient temperature, and θJA is the junction-to-ambient thermal resistance for
the 10-pin SON package. VIN is the input voltage to the LM2751, VVOUT is the voltage at the output of the device,
and IOUT is the total current supplied to the load connected to VOUT
.
PDISSIPATION = PIN - POUT
(6)
(7)
(8)
= (VIN × IIN) − (VVOUT × IOUT
)
TJ = TA + (PDISSIPATION × θJA)
The junction temperature rating takes precedence over the ambient temperature rating. The LM2751 may be
operated outside the ambient temperature rating, so long as the junction temperature of the device does not
exceed the maximum operating rating of 115°C. The maximum ambient temperature rating must be derated in
applications where high power dissipation and/or poor thermal resistance causes the junction temperature to
exceed 115°C.
12
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM2751
LM2751
www.ti.com
SNVS299B –APRIL 2005–REVISED MAY 2013
REVISION HISTORY
Changes from Revision A (May 2013) to Revision B
Page
•
Changed layout of National Data Sheet to TI format .......................................................................................................... 12
Copyright © 2005–2013, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: LM2751
PACKAGE OPTION ADDENDUM
www.ti.com
7-Oct-2013
PACKAGING INFORMATION
Orderable Device
LM2751SD-A/NOPB
LM2751SD-B/NOPB
LM2751SDX-A/NOPB
LM2751SDX-B/NOPB
Status Package Type Package Pins Package
Eco Plan Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-40 to 85
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
ACTIVE
WSON
WSON
WSON
WSON
DSC
10
10
10
10
1000
Green (RoHS
& no Sb/Br)
CU SN
CU SN
CU SN
CU SN
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
L145B
ACTIVE
ACTIVE
ACTIVE
DSC
DSC
DSC
1000
4500
4500
Green (RoHS
& no Sb/Br)
-40 to 85
L146B
L145B
L146B
Green (RoHS
& no Sb/Br)
-40 to 85
Green (RoHS
& no Sb/Br)
-40 to 85
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
7-Oct-2013
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LM2751SD-A/NOPB
LM2751SD-B/NOPB
LM2751SDX-A/NOPB
LM2751SDX-B/NOPB
WSON
WSON
WSON
WSON
DSC
DSC
DSC
DSC
10
10
10
10
1000
1000
4500
4500
178.0
178.0
330.0
330.0
12.4
12.4
12.4
12.4
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
1.0
1.0
1.0
1.0
8.0
8.0
8.0
8.0
12.0
12.0
12.0
12.0
Q1
Q1
Q1
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
LM2751SD-A/NOPB
LM2751SD-B/NOPB
LM2751SDX-A/NOPB
LM2751SDX-B/NOPB
WSON
WSON
WSON
WSON
DSC
DSC
DSC
DSC
10
10
10
10
1000
1000
4500
4500
210.0
210.0
367.0
367.0
185.0
185.0
367.0
367.0
35.0
35.0
35.0
35.0
Pack Materials-Page 2
MECHANICAL DATA
DSC0010A
SDA10A (Rev A)
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明