LM2901MWC [TI]
IC QUAD COMPARATOR, 15000 uV OFFSET-MAX, 1300 ns RESPONSE TIME, UUC, DIE, Comparator;
| 型号： | LM2901MWC |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | IC QUAD COMPARATOR, 15000 uV OFFSET-MAX, 1300 ns RESPONSE TIME, UUC, DIE, Comparator |
| 文件： | 总20页 (文件大小：496K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
National Semiconductor is now part of
Texas Instruments.
Search http://www.ti.com/ for the latest technical
information and details on our current products and services.
March 2004
LM139/LM239/LM339/LM2901/LM3302
Low Power Low Offset Voltage Quad Comparators
General Description
Features
n Wide supply voltage range
n LM139/139A Series
n LM2901:
The LM139 series consists of four independent precision
voltage comparators with an offset voltage specification as
low as 2 mV max for all four comparators. These were
designed specifically to operate from a single power supply
over a wide range of voltages. Operation from split power
supplies is also possible and the low power supply current
drain is independent of the magnitude of the power supply
voltage. These comparators also have a unique characteris-
tic in that the input common-mode voltage range includes
ground, even though operated from a single power supply
voltage.
2 to 36 VDC or 1 to 18 VDC
2 to 36 VDC or 1 to 18 VDC
2 to 28 VDC or 1 to 14 VDC
n LM3302:
n Very low supply current drain (0.8 mA) — independent
of supply voltage
n Low input biasing current:
n Low input offset current:
25 nA
5 nA
3 mV
n Offset voltage:
n Input common-mode voltage range includes GND
n Differential input voltage range equal to the power
supply voltage
n Low output saturation voltage:
n Output voltage compatible with TTL, DTL, ECL, MOS
Application areas include limit comparators, simple analog to
digital converters; pulse, squarewave and time delay gen-
erators; wide range VCO; MOS clock timers; multivibrators
and high voltage digital logic gates. The LM139 series was
designed to directly interface with TTL and CMOS. When
operated from both plus and minus power supplies, they will
directly interface with MOS logic— where the low power
drain of the LM339 is a distinct advantage over standard
comparators.
250 mV at 4 mA
and CMOS logic systems
Advantages
n High precision comparators
n Reduced VOS drift over temperature
n Eliminates need for dual supplies
n Allows sensing near GND
n Compatible with all forms of logic
n Power drain suitable for battery operation
One-Shot Multivibrator with Input
Lock Out
00570612
© 2004 National Semiconductor Corporation
DS005706
www.national.com
Distributors for availability and specifications.
LM139/LM239/LM339
Absolute Maximum Ratings (Note 10)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
LM139A/LM239A/LM339A
LM2901
LM3302
Supply Voltage, V+
36 VDC or 18 VDC
36 VDC
28 VDC or 14 VDC
28 VDC
Differential Input Voltage (Note 8)
Input Voltage
−0.3 VDC to +36 VDC
−0.3 VDC to +28 VDC
<
Input Current (VIN −0.3 VDC),
(Note 3)
50 mA
50 mA
Power Dissipation (Note 1)
Molded DIP
1050 mW
1190 mW
760 mW
1050 mW
Cavity DIP
Small Outline Package
Output Short-Circuit to GND,
(Note 2)
Continuous
Continuous
Storage Temperature Range
Lead Temperature
(Soldering, 10 seconds)
Operating Temperature Range
LM339/LM339A
−65˚C to +150˚C
−65˚C to +150˚C
260˚C
260˚C
−40˚C to +85˚C
0˚C to +70˚C
−25˚C to +85˚C
−40˚C to +85˚C
−55˚C to +125˚C
LM239/LM239A
LM2901
LM139/LM139A
Soldering Information
Dual-In-Line Package
Soldering (10 seconds)
Small Outline Package
Vapor Phase (60 seconds)
Infrared (15 seconds)
260˚C
260˚C
215˚C
220˚C
215˚C
220˚C
See AN-450 “Surface Mounting Methods and Their Effect on Product Reliability” for other methods of
soldering surface mount devices.
ESD rating (1.5 kΩ in series with 100 pF)
600V
600V
Electrical Characteristics
(V+=5 VDC, TA = 25˚C, unless otherwise stated)
Parameter
Conditions
LM139A
LM239A, LM339A
LM139
Units
Min Typ Max
Min Typ Max Min Typ Max
Input Offset Voltage
Input Bias Current
(Note 9)
1.0
25
2.0
1.0
25
2.0
2.0
25
5.0
mVDC
nADC
IIN(+) or IIN(−) with Output in
100
250
100
Linear Range, (Note 5), VCM=0V
Input Offset Current
Input Common-Mode
Voltage Range
I
IN(+)−IIN(−), VCM=0V
3.0
0.8
25
V+−1.5
5.0
50
V+−1.5
3.0
25
nADC
V+=30 VDC (LM3302,
V+ = 28 VDC) (Note 6)
0
0
0
V+−1.5 VDC
∞
∞
Supply Current
RL
=
=
on all Comparators,
2.0
0.8
1.0
2.0
2.5
0.8
1.0
2.0
2.5
mADC
mADC
+
RL
, V = 36V,
(LM3302, V+ = 28 VDC
)
Voltage Gain
RL≥15 kΩ, V+ = 15 VDC
50 200
300
50
200
300
50 200
300
V/mV
ns
VO = 1 VDC to 11 VDC
Large Signal
VIN = TTL Logic Swing, VREF =
Response Time
1.4 VDC, VRL = 5 VDC,
www.national.com
2
Electrical Characteristics (Continued)
(V+=5 VDC, TA = 25˚C, unless otherwise stated)
Parameter
Conditions
LM139A
LM239A, LM339A
LM139
Units
Min Typ Max
Min Typ Max Min Typ Max
RL = 5.1 kΩ
Response Time
VRL = 5 VDC, RL = 5.1 kΩ,
(Note 7)
1.3
6.0 16
250 400
0.1
1.3
1.3
µs
Output Sink Current
Saturation Voltage
VIN(−) = 1 VDC, VIN(+) = 0,
VO ≤ 1.5 VDC
6.0
16
6.0 16
mADC
mVDC
nADC
VIN(−) = 1 VDC, VIN(+) = 0,
ISINK ≤ 4 mA
250 400
0.1
250 400
Output Leakage
Current
VIN(+) = 1 VDC,VIN(−) = 0,
VO = 5 VDC
0.1
Electrical Characteristics
(V+ = 5 VDC, TA = 25˚C, unless otherwise stated)
Parameter
Conditions
LM239, LM339
LM2901
LM3302
Units
Min Typ Max Min Typ Max
Min Typ Max
Input Offset Voltage
Input Bias Current
(Note 9)
2.0
25
5.0
2.0
25
7.0
3
20
mVDC
nADC
IIN(+) or IIN(−) with Output in
250
250
25
500
Linear Range, (Note 5), VCM=0V
Input Offset Current
Input Common-Mode
Voltage Range
I
IN(+)−IIN(−), VCM = 0V
5.0
50
V+−1.5
5
50
V+−1.5
3
100
V+−1.5 VDC
nADC
V+ = 30 VDC (LM3302,
V+ = 28 VDC) (Note 6)
0
0
0
2
∞
∞
Supply Current
RL
=
=
on all Comparators,
0.8
1.0
2.0
2.5
0.8
1.0
2.0
2.5
0.8
1.0
2.0
2.5
mADC
mADC
+
RL
, V = 36V,
(LM3302, V+ = 28 VDC
RL ≥ 15 kΩ, V+ = 15 VDC
)
Voltage Gain
50
200
300
25 100
300
30
V/mV
ns
VO = 1 VDC to 11 VDC
Large Signal
VIN = TTL Logic Swing, VREF
=
300
Response Time
1.4 VDC, VRL = 5 VDC,
RL = 5.1 kΩ,
Response Time
VRL = 5 VDC, RL = 5.1 kΩ,
1.3
16
1.3
1.3
µs
(Note 7)
Output Sink Current
Saturation Voltage
V
IN(−)= 1 VDC, VIN(+) = 0,
6.0
6.0 16
6.0 16
mADC
mVDC
nADC
VO ≤ 1.5 VDC
VIN(−) = 1 VDC, VIN(+) = 0,
ISINK ≤ 4 mA
250 400
0.1
250 400
0.1
250 500
0.1
Output Leakage
Current
VIN(+) = 1 VDC,VIN(−) = 0,
VO = 5 VDC
Electrical Characteristics
(V+ = 5.0 VDC, (Note 4))
Parameter
Conditions
LM139A
LM239A, LM339A
LM139
Units
Min Typ Max Min Typ Max Min Typ Max
Input Offset Voltage
Input Offset Current
Input Bias Current
(Note 9)
4.0
100
300
4.0
150
400
9.0
100
300
mVDC
nADC
nADC
IIN(+)−IIN(−), VCM = 0V
IIN(+) or IIN(−) with Output in
Linear Range, VCM = 0V (Note 5)
V+=30 VDC (LM3302,
Input Common-Mode
Voltage Range
0
V+−2.0
0
V+−2.0
0
V+−2.0 VDC
V+ = 28 VDC) (Note 6)
3
www.national.com
Electrical Characteristics (Continued)
(V+ = 5.0 VDC, (Note 4))
Parameter
Conditions
LM139A
LM239A, LM339A
LM139
Units
Min Typ Max Min Typ Max Min Typ Max
Saturation Voltage
V
IN(−)=1 VDC, VIN(+) = 0,
700
1.0
700
1.0
700 mVDC
ISINK ≤ 4 mA
Output Leakage Current
VIN(+) = 1 VDC, VIN(−) = 0,
VO = 30 VDC, (LM3302,
1.0
36
µADC
VO = 28 VDC
Keep all VIN’s ≥ 0 VDC (or V−,
)
Differential Input Voltage
36
36
VDC
if used), (Note 8)
Electrical Characteristics
(V+ = 5.0 VDC, (Note 4))
Parameter
Conditions
LM239, LM339
LM2901
LM3302
Units
Min Typ Max Min Typ Max Min Typ Max
Input Offset Voltage
Input Offset Current
Input Bias Current
(Note 9)
9.0
150
400
9
15
40
mVDC
nADC
IIN(+)−IIN(−), VCM = 0V
IIN(+) or IIN(−) with Output in
Linear Range, VCM = 0V (Note 5)
V+ = 30 VDC (LM3302, V+ = 28 VDC
(Note 6)
50
200
300
200 500
V+−2.0
400 700
1.0
1000 nADC
V+−2.0 VDC
700 mVDC
Input Common-Mode
Voltage Range
)
V+−2.0
700
1.0
0
0
Saturation Voltage
VIN(−) = 1 VDC, VIN(+) = 0,
ISINK ≤ 4 mA
Output Leakage Current VIN(+) = 1 VDC, VIN(−) = 0,
1.0
28
µADC
VDC
VO = 30 VDC, (LM3302, V = 28 VDC
)
O
Differential Input Voltage Keep all VIN’s ≥ 0 VDC (or V−,
36
36
if used), (Note 8)
Note 1: For operating at high temperatures, the LM339/LM339A, LM2901, LM3302 must be derated based on a 125˚C maximum junction temperature and a
thermal resistance of 95˚C/W which applies for the device soldered in a printed circuit board, operating in a still air ambient. The LM239 and LM139 must be derated
based on a 150˚C maximum junction temperature. The low bias dissipation and the “ON-OFF” characteristic of the outputs keeps the chip dissipation very small
(P ≤100 mW), provided the output transistors are allowed to saturate.
D
+
Note 2: Short circuits from the output to V can cause excessive heating and eventual destruction. When considering short circuits to ground, the maximum output
+
current is approximately 20 mA independent of the magnitude of V .
Note 3: This input current will only exist when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of the input PNP
transistors becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is also lateral NPN parasitic transistor action
+
on the IC chip. This transistor action can cause the output voltages of the comparators to go to the V voltage level (or to ground for a large overdrive) for the time
duration that an input is driven negative. This is not destructive and normal output states will re-establish when the input voltage, which was negative, again returns
to a value greater than −0.3 V
(at 25˚)C.
DC
Note 4: These specifications are limited to −55˚C ≤ T ≤ +125˚C, for the LM139/LM139A. With the LM239/LM239A, all temperature specifications are limited to
A
−25˚C ≤ T ≤ +85˚C, the LM339/LM339A temperature specifications are limited to 0˚C ≤ T ≤ +70˚C, and the LM2901, LM3302 temperature range is −40˚C ≤ T
A
A
A
≤ +85˚C.
Note 5: The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the output so
no loading change exists on the reference or input lines.
Note 6: The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end of the common-mode
+
+
voltage range is V −1.5V at 25˚C, but either or both inputs can go to +30 V
without damage (25V for LM3302), independent of the magnitude of V .
DC
Note 7: The response time specified is a 100 mV input step with 5 mV overdrive. For larger overdrive signals 300 ns can be obtained, see typical performance
characteristics section.
Note 8: Positive excursions of input voltage may exceed the power supply level. As long as the other voltage remains within the common-mode range, the
comparator will provide a proper output state. The low input voltage state must not be less than −0.3 V
(or 0.3 V below the magnitude of the negative power
DC
DC
supply, if used) (at 25˚C).
+
+
Note 9: At output switch point, V .1.4 V , R = 0Ω with V from 5 V to 30 V ; and over the full input common-mode range (0 V to V −1.5 V ), at 25˚C.
O
DC
S
DC
DC
DC
DC
+
For LM3302, V from 5 V
to 28 V
.
DC
DC
Note 10: Refer to RETS139AX for LM139A military specifications and to RETS139X for LM139 military specifications.
www.national.com
4
Typical Performance Characteristics LM139/LM239/LM339, LM139A/LM239A/LM339A, LM3302
Supply Current
Input Current
00570634
00570635
Response Time for Various Input Overdrives
—Negative Transition
Output Saturation Voltage
00570637
00570636
Response Time for Various Input Overdrives
—Positive Transition
00570638
5
www.national.com
Typical Performance Characteristics LM2901
Supply Current
Input Current
00570640
00570639
Response Time for Various Input Overdrives
—Negative Transition
Output Saturation Voltage
00570641
00570642
Response Time for Various Input Overdrives
—Positive Transition
00570643
www.national.com
6
Application Hints
Driving CMOS
The LM139 series are high gain, wide bandwidth devices
which, like most comparators, can easily oscillate if the
output lead is inadvertently allowed to capacitively couple to
the inputs via stray capacitance. This shows up only during
the output voltage transition intervals as the comparator
changes states. Power supply bypassing is not required to
solve this problem. Standard PC board layout is helpful as it
reduces stray input-output coupling. Reducing this input re-
<
sistors to
10 kΩ reduces the feedback signal levels and
finally, adding even a small amount (1 to 10 mV) of positive
feedback (hysteresis) causes such a rapid transition that
oscillations due to stray feedback are not possible. Simply
socketing the IC and attaching resistors to the pins will cause
input-output oscillations during the small transition intervals
unless hysteresis is used. If the input signal is a pulse
waveform, with relatively fast rise and fall times, hysteresis is
not required.
00570604
Driving TTL
All pins of any unused comparators should be tied to the
negative supply.
The bias network of the LM139 series establishes a drain
current which is independent of the magnitude of the power
supply voltage over the range of from 2 VDC to 30 VDC
.
It is usually unnecessary to use a bypass capacitor across
the power supply line.
00570605
The differential input voltage may be larger than V+ without
damaging the device. Protection should be provided to pre-
vent the input voltages from going negative more than −0.3
VDC (at 25˚C). An input clamp diode can be used as shown
in the applications section.
AND Gate
The output of the LM139 series is the uncommitted collector
of a grounded-emitter NPN output transistor. Many collectors
can be tied together to provide an output OR’ing function. An
output pull-up resistor can be connected to any available
power supply voltage within the permitted supply voltage
range and there is no restriction on this voltage due to the
magnitude of the voltage which is applied to the V+ terminal
of the LM139A package. The output can also be used as a
simple SPST switch to ground (when a pull-up resistor is not
used). The amount of current which the output device can
sink is limited by the drive available (which is independent of
V+) and the β of this device. When the maximum current limit
is reached (approximately 16 mA), the output transistor will
come out of saturation and the output voltage will rise very
rapidly. The output saturation voltage is limited by the ap-
proximately 60Ω RSAT of the output transistor. The low offset
voltage of the output transistor (1 mV) allows the output to
clamp essentially to ground level for small load currents.
00570608
OR Gate
Typical Applications (V+ = 5.0 VDC
)
Basic Comparator
00570603
00570609
7
www.national.com
Typical Applications (V+= 15 VDC
)
One-Shot Multivibrator
00570610
Bi-Stable Multivibrator
00570611
www.national.com
8
Typical Applications (V+= 15 VDC) (Continued)
One-Shot Multivibrator with Input Lock Out
00570612
Pulse Generator
00570617
9
www.national.com
Typical Applications (V+= 15
ORing the Outputs
VDC) (Continued)
Large Fan-In AND Gate
00570613
00570615
www.national.com
10
Typical Applications (V+= 15 VDC) (Continued)
Time Delay Generator
00570614
Non-Inverting Comparator with Hysteresis
Inverting Comparator with Hysteresis
00570618
00570619
11
www.national.com
Typical Applications (V+= 15
Comparing Input Voltages
of Opposite Polarity
VDC) (Continued)
Squarewave Oscillator
00570620
Output Strobing
00570616
Basic Comparator
00570622
* Or open-collector logic gate without pull-up resistor
Crystal Controlled Oscillator
00570621
Limit Comparator
00570625
00570624
www.national.com
12
13
www.national.com
Typical Applications (V+= 15
Zero Crossing Detector (Single Power Supply)
VDC) (Continued)
Transducer Amplifier
00570630
Split-Supply Applications (V+ = +15
VDC and V− = −15 VDC
)
00570628
MOS Clock Driver
00570631
www.national.com
14
Split-Supply Applications (V+ = +15 VDC
Comparator With a Negative Reference
and V− = −15 VDC) (Continued)
Zero Crossing Detector
00570633
Schematic Diagram
00570632
00570601
15
www.national.com
Connection Diagrams
Dual-In-Line Package
00570602
Order Number LM139J, LM139J/883 (Note 11), LM139AJ,
LM139AJ/883 (Note 12), LM239J, LM239AJ, LM339J
See NS Package Number J14A
Order Number LM339AM, LM339AMX, LM339M, LM339MX or LM2901M
See NS Package Number M14A
Order Number LM339N, LM339AN, LM2901N or LM3302N
See NS Package Number N14A
00570627
Order Number LM139AW/883 or LM139W/883 (Note 11)
See NS Package Number W14B,
LM139AWGRQMLV (Note 13)
See NS Package Number WG14A
Note 11: Available per JM38510/11201
Note 12: Available per SMD# 5962-8873901
Note 13: See STD Mil Dwg 5962R96738 for Radiation Tolerant Device
www.national.com
16
Physical Dimensions inches (millimeters)
unless otherwise noted
Ceramic Dual-In-Line Package (J)
Order Number LM139J, LM139J/883, LM139AJ,
LM139AJ/883, LM239J, LM239AJ, LM339J
NS Package Number J14A
S.O. Package (M)
Order Number LM339AM, LM339AMX, LM339M, LM339MX, LM2901M or LM2901MX
NS Package Number M14A
17
www.national.com
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
Molded Dual-In-Line Package (N)
Order Number LM339N, LM339AN, LM2901N or LM3302N
NS Package Number N14A
Order Number LM139AW/883, LM139W/883
NS Package Number W14B
www.national.com
18
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
Order Number LM139AWG/883, LM139WG/883
NS Package Number WG14A
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products
Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification
(CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2.
National Semiconductor
Americas Customer
Support Center
National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
National Semiconductor
Asia Pacific Customer
Support Center
National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: new.feedback@nsc.com
Tel: 1-800-272-9959
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
Email: ap.support@nsc.com
Email: jpn.feedback@nsc.com
Tel: 81-3-5639-7560
www.national.com
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
相关型号：
©2020 ICPDF网 联系我们和版权申明