LM2904ITPX/NOPB [TI]
Dual, 26-V, 1-MHz op amp | YPB | 8 | -40 to 85;型号: | LM2904ITPX/NOPB |
厂家: | TEXAS INSTRUMENTS |
描述: | Dual, 26-V, 1-MHz op amp | YPB | 8 | -40 to 85 放大器 运算放大器 放大器电路 |
文件: | 总33页 (文件大小:1727K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LM158-N, LM258-N, LM2904-N, LM358-N
www.ti.com
SNOSBT3H –JANUARY 2000–REVISED MARCH 2013
LM158/LM258/LM358/LM2904 Low Power Dual Operational Amplifiers
Check for Samples: LM158-N, LM258-N, LM2904-N, LM358-N
1
FEATURES
ADVANTAGES
2
•
Available in 8-Bump DSBGA Chip-
Sized Package, (See AN-1112 (SNVA009))
•
•
•
Two Internally Compensated Op Amps
Eliminates Need for Dual Supplies
•
Internally Frequency Compensated for Unity
Gain
Allows Direct Sensing Near GND and VOUT
Also Goes to GND
•
•
Large DC Voltage Gain: 100 dB
•
•
Compatible with All Forms of Logic
Wide Bandwidth (Unity Gain): 1 MHz
(Temperature Compensated)
Power Drain Suitable for Battery Operation
•
Wide Power Supply Range:
DESCRIPTION
The LM158 series consists of two independent, high
gain, internally frequency compensated operational
amplifiers which were designed specifically to operate
from a single power supply over a wide range of
voltages. Operation from split power supplies is also
possible and the low power supply current drain is
independent of the magnitude of the power supply
voltage.
–
–
Single Supply: 3V to 32V
Or Dual Supplies: ±1.5V to ±16V
•
Very Low Supply Current Drain (500
μA)—Essentially Independent of Supply
Voltage
•
•
Low Input Offset Voltage: 2 mV
Input Common-Mode Voltage Range Includes
Ground
Application areas include transducer amplifiers, dc
gain blocks and all the conventional op amp circuits
which now can be more easily implemented in single
power supply systems. For example, the LM158
series can be directly operated off of the standard
+5V power supply voltage which is used in digital
systems and will easily provide the required interface
electronics without requiring the additional ±15V
power supplies.
•
•
Differential Input Voltage Range Equal to the
Power Supply Voltage
Large Output Voltage Swing
UNIQUE CHARACTERISTICS
•
In the Llinear Mode the Input Common-Mode
Voltage Range Includes Ground and the
Output Voltage Can Also Swing to Ground,
even though Operated from Only a Single
Power Supply Voltage.
The LM358 and LM2904 are available in a chip sized
package (8-Bump DSBGA) using TI's DSBGA
package technology.
•
•
The Unity Gain Cross Frequency is
Temperature Compensated.
The Input Bias Current is also Temperature
Compensated.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2000–2013, Texas Instruments Incorporated
LM158-N, LM258-N, LM2904-N, LM358-N
SNOSBT3H –JANUARY 2000–REVISED MARCH 2013
www.ti.com
Voltage Controlled Oscillator (VCO)
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
2
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM158-N LM258-N LM2904-N LM358-N
LM158-N, LM258-N, LM2904-N, LM358-N
www.ti.com
SNOSBT3H –JANUARY 2000–REVISED MARCH 2013
ABSOLUTE MAXIMUM RATINGS(1)(2)
LM158/LM258/LM358
LM2904
LM158A/LM258A/LM3
58A
Supply Voltage, V+
Differential Input Voltage
Input Voltage
32V
32V
26V
26V
−0.3V to +32V
−0.3V to +26V
Power Dissipation(3)
PDIP (P)
830 mW
550 mW
530 mW
435mW
830 mW
530 mW
TO-99 (LMC)
SOIC (D)
DSBGA (YPB)
Output Short-Circuit to GND (One
Amplifier)(4)
Input Current (VIN < −0.3V)(5)
Operating Temperature Range
LM358
V+ ≤ 15V and TA = 25°C
Continuous
Continuous
50 mA
50 mA
0°C to +70°C
−25°C to +85°C
−55°C to +125°C
−65°C to +150°C
−40°C to +85°C
LM258
LM158
Storage Temperature Range
Lead Temperature, PDIP (P)
(Soldering, 10 seconds)
Lead Temperature, TO-99 (LMC)
(Soldering, 10 seconds)
Soldering Information
PDIP Package (P)
−65°C to +150°C
260°C
260°C
300°C
300°C
Soldering (10 seconds)
SOIC Package (D)
260°C
260°C
Vapor Phase (60 seconds)
Infrared (15 seconds)
ESD Tolerance(6)
215°C
220°C
250V
215°C
220°C
250V
(1) Refer to RETS158AX for LM158A military specifications and to RETS158X for LM158 military specifications.
(2) If Military/Aerospace specified devices are required, please contact the TI Sales Office/Distributors for availability and specifications.
(3) For operating at high temperatures, the LM358/LM358A, LM2904 must be derated based on a +125°C maximum junction temperature
and a thermal resistance of 120°C/W for PDIP, 182°C/W for TO-99, 189°C/W for SOIC package, and 230°C/W for DSBGA, which
applies for the device soldered in a printed circuit board, operating in a still air ambient. The LM258/LM258A and LM158/LM158A can be
derated based on a +150°C maximum junction temperature. The dissipation is the total of both amplifiers—use external resistors, where
possible, to allow the amplifier to saturate or to reduce the power which is dissipated in the integrated circuit.
(4) Short circuits from the output to V+ can cause excessive heating and eventual destruction. When considering short circuits to ground,
the maximum output current is approximately 40 mA independent of the magnitude of V+. At values of supply voltage in excess of +15V,
continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction. Destructive dissipation can result
from simultaneous shorts on all amplifiers.
(5) This input current will only exist when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of
the input PNP transistors becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is
also lateral NPN parasitic transistor action on the IC chip. This transistor action can cause the output voltages of the op amps to go to
the V+voltage level (or to ground for a large overdrive) for the time duration that an input is driven negative. This is not destructive and
normal output states will re-establish when the input voltage, which was negative, again returns to a value greater than −0.3V (at 25°C).
(6) Human body model, 1.5 kΩ in series with 100 pF.
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LM158-N LM258-N LM2904-N LM358-N
LM158-N, LM258-N, LM2904-N, LM358-N
SNOSBT3H –JANUARY 2000–REVISED MARCH 2013
www.ti.com
ELECTRICAL CHARACTERISTICS
V+ = +5.0V, unless otherwise stated
Parameter
Conditions
LM158A
LM358A
LM158/LM258
Units
Min Typ Max Min Typ Max Min Typ Max
Input Offset Voltage
Input Bias Current
(1), TA = 25°C
1
2
2
3
2
5
mV
nA
IIN(+) or IIN(−), TA = 25°C,
VCM = 0V,(2)
20
50
45
100
45
150
Input Offset Current
Input Common-Mode
Voltage Range
I
IN(+) − IIN(−), VCM = 0V, TA = 25°C
2
10
5
30
3
30
nA
V+ = 30V,(3)
0
V+−1.5
0
V+−1.5
0
V+−1.5
V
(LM2904, V+ = 26V), TA = 25°C
Over Full Temperature Range
RL = ∞ on All Op Amps
V+ = 30V (LM2904 V+ = 26V)
V+ = 5V
Supply Current
1
2
1
2
1
2
mA
mA
0.5
1.2
0.5
1.2
0.5
1.2
(1)
V
O ≃ 1.4V, RS = 0Ω with V+ from 5V to 30V; and over the full input common-mode range (0V to V+ −1.5V) at 25°C. For LM2904, V+ from
5V to 26V.
(2) The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the
state of the output so no loading change exists on the input lines.
(3) The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (at 25°C). The
upper end of the common-mode voltage range is V+ −1.5V (at 25°C), but either or both inputs can go to +32V without damage (+26V for
LM2904), independent of the magnitude of V+.
ELECTRICAL CHARACTERISTICS
V+ = +5.0V, unless otherwise stated
Parameter
Conditions
LM358
Typ
2
LM2904
Typ
Units
Min
Max
Min
Max
Input Offset Voltage
Input Bias Current
See(1) , TA = 25°C
7
2
7
mV
nA
nA
V
IIN(+) or IIN(−), TA = 25°C,
VCM = 0V, See(2)
45
5
250
50
V+−1.
45
5
250
50
V+−1.
Input Offset Current
IIN(+) − IIN(−), VCM = 0V, TA = 25°C
Input Common-Mode
Voltage Range
V+ = 30V, See(3)
0
0
(LM2904, V+ = 26V), TA = 25°C
5
5
Supply Current
Over Full Temperature Range
RL = ∞ on All Op Amps
V+ = 30V (LM2904 V+ = 26V)
V+ = 5V
1
2
1
2
mA
mA
0.5
1.2
0.5
1.2
(1)
V
O ≃ 1.4V, RS = 0Ω with V+ from 5V to 30V; and over the full input common-mode range (0V to V+ −1.5V) at 25°C. For LM2904, V+ from
5V to 26V.
(2) The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the
state of the output so no loading change exists on the input lines.
(3) The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (at 25°C). The
upper end of the common-mode voltage range is V+ −1.5V (at 25°C), but either or both inputs can go to +32V without damage (+26V for
LM2904), independent of the magnitude of V+.
4
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM158-N LM258-N LM2904-N LM358-N
LM158-N, LM258-N, LM2904-N, LM358-N
www.ti.com
SNOSBT3H –JANUARY 2000–REVISED MARCH 2013
ELECTRICAL CHARACTERISTICS
V+ = +5.0V, See(1), unless otherwise stated
LM158A
LM358A
LM158/LM258
Units
Parameter
Conditions
V+ = 15V, TA = 25°C,
Min Typ Max Min Typ Max Min Typ Max
Large Signal Voltage
Gain
50
100
25
100
50
100
V/mV
RL ≥ 2 kΩ, (For VO = 1V to 11V)
Common-Mode
Rejection Ratio
Power Supply
Rejection Ratio
TA = 25°C,
70
65
85
65
65
85
70
65
85
dB
dB
VCM = 0V to V+−1.5V
V+ = 5V to 30V
(LM2904, V+ = 5V to 26V), TA = 25°C
100
100
100
Amplifier-to-Amplifier
Coupling
f = 1 kHz to 20 kHz, TA = 25°C (Input
Referred), See(2)
−120
−120
−120
dB
Output Current
Source VIN+ = 1V,
VIN− = 0V,
V+ = 15V,
20
10
12
40
20
10
12
40
20
10
12
40
mA
VO = 2V, TA = 25°C
Sink VIN− = 1V, VIN+ = 0V
V+ = 15V, TA = 25°C,
VO = 2V
20
50
20
50
20
50
mA
VIN− = 1V,
VIN+ = 0V
μA
TA = 25°C, VO = 200 mV,
V+ = 15V
Short Circuit to Ground
Input Offset Voltage
TA = 25°C, See(3), V+ = 15V
See(4)
40
7
60
4
40
7
60
5
40
7
60
7
mA
mV
Input Offset Voltage Drift RS = 0Ω
15
20
μV/°C
nA
Input Offset Current
Input Offset Current Drift
Input Bias Current
IIN(+) − IIN(−)
30
75
100
RS = 0Ω
10
40
200
100
10
40
300
200
10
40
pA/°C
nA
IIN(+) or IIN(−)
300
Input Common-Mode
Voltage Range
V+ = 30 V, See(5) (LM2904, V+ = 26V)
0
V+−2
0
V+−2
0
V+−2
V
Large Signal Voltage
Gain
V+ = +15V
(VO = 1V to 11V)
25
15
25
V/mV
R
L ≥ 2 kΩ
VOH V+ = +30V
(LM2904, V+ = 26V)
VOL V+ = 5V, RL = 10 kΩ
Output
Voltage
Swing
RL = 2 kΩ
26
27
26
27
26
27
V
V
RL = 10 kΩ
28
5
28
5
28
5
20
20
20
mV
(1) These specifications are limited to −55°C ≤ TA ≤ +125°C for the LM158/LM158A. With the LM258/LM258A, all temperature
specifications are limited to −25°C ≤ TA ≤ +85°C, the LM358/LM358A temperature specifications are limited to 0°C ≤ TA ≤ +70°C, and
the LM2904 specifications are limited to −40°C ≤ TA ≤ +85°C.
(2) Due to proximity of external components, insure that coupling is not originating via stray capacitance between these external parts. This
typically can be detected as this type of capacitance increases at higher frequencies.
(3) Short circuits from the output to V+ can cause excessive heating and eventual destruction. When considering short circuits to ground,
the maximum output current is approximately 40 mA independent of the magnitude of V+. At values of supply voltage in excess of +15V,
continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction. Destructive dissipation can result
from simultaneous shorts on all amplifiers.
(4)
V
O ≃ 1.4V, RS = 0Ω with V+ from 5V to 30V; and over the full input common-mode range (0V to V+ −1.5V) at 25°C. For LM2904, V+ from
5V to 26V.
(5) The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (at 25°C). The
upper end of the common-mode voltage range is V+ −1.5V (at 25°C), but either or both inputs can go to +32V without damage (+26V for
LM2904), independent of the magnitude of V+.
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: LM158-N LM258-N LM2904-N LM358-N
LM158-N, LM258-N, LM2904-N, LM358-N
SNOSBT3H –JANUARY 2000–REVISED MARCH 2013
www.ti.com
Units
ELECTRICAL CHARACTERISTICS (continued)
V+ = +5.0V, See(1), unless otherwise stated
LM158A
LM358A
LM158/LM258
Parameter
Output Current
Conditions
Source VIN+ = +1V, VIN− = 0V,
Min Typ Max Min Typ Max Min Typ Max
10
10
20
15
10
5
20
8
10
5
20
8
mA
mA
V+ = 15V, VO = 2V
Sink VIN− = +1V, VIN+ = 0V,
V+ = 15V, VO = 2V
ELECTRICAL CHARACTERISTICS
V+ = +5.0V, See(1), unless otherwise stated
LM358
Typ
LM2904
Typ
Units
Parameter
Conditions
V+ = 15V, TA = 25°C,
L ≥ 2 kΩ, (For VO = 1V to 11V)
Min
Max
Min
Max
Large Signal Voltage
Gain
R
25
65
65
100
85
25
50
50
100
70
V/mV
dB
Common-Mode
Rejection Ratio
TA = 25°C,
VCM = 0V to V+−1.5V
V+ = 5V to 30V
(LM2904, V+ = 5V to 26V), TA = 25°C
Power Supply
Rejection Ratio
100
100
dB
Amplifier-to-Amplifier Coupling
f = 1 kHz to 20 kHz, TA = 25°C
(Input Referred), See(2)
−120
−120
dB
Output Current
Source VIN+ = 1V,
VIN− = 0V,
V+ = 15V,
20
10
12
40
20
10
12
40
mA
VO = 2V, TA = 25°C
Sink VIN− = 1V, VIN+ = 0V
V+ = 15V, TA = 25°C,
VO = 2V
20
50
20
mA
VIN− = 1V,
VIN+ = 0V
50
40
μA
TA = 25°C, VO = 200 mV,
V+ = 15V
TA = 25°C, See(3), V+ = 15V
See(4)
Short Circuit to Ground
Input Offset Voltage
Input Offset Voltage Drift
Input Offset Current
Input Offset Current Drift
Input Bias Current
40
7
60
9
60
10
mA
mV
RS = 0Ω
7
μV/°C
nA
IIN(+) − IIN(−)
150
45
10
40
200
RS = 0Ω
10
40
pA/°C
nA
IIN(+) or IIN(−)
500
500
Input Common-Mode
Voltage Range
V+ = 30 V, See(5) (LM2904, V+ = 26V)
0
V+−2
0
V+ −2
V
(1) These specifications are limited to −55°C ≤ TA ≤ +125°C for the LM158/LM158A. With the LM258/LM258A, all temperature
specifications are limited to −25°C ≤ TA ≤ +85°C, the LM358/LM358A temperature specifications are limited to 0°C ≤ TA ≤ +70°C, and
the LM2904 specifications are limited to −40°C ≤ TA ≤ +85°C.
(2) Due to proximity of external components, insure that coupling is not originating via stray capacitance between these external parts. This
typically can be detected as this type of capacitance increases at higher frequencies.
(3) Short circuits from the output to V+ can cause excessive heating and eventual destruction. When considering short circuits to ground,
the maximum output current is approximately 40 mA independent of the magnitude of V+. At values of supply voltage in excess of +15V,
continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction. Destructive dissipation can result
from simultaneous shorts on all amplifiers.
(4)
V
O ≃ 1.4V, RS = 0Ω with V+ from 5V to 30V; and over the full input common-mode range (0V to V+ −1.5V) at 25°C. For LM2904, V+ from
5V to 26V.
(5) The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (at 25°C). The
upper end of the common-mode voltage range is V+ −1.5V (at 25°C), but either or both inputs can go to +32V without damage (+26V for
LM2904), independent of the magnitude of V+.
6
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM158-N LM258-N LM2904-N LM358-N
LM158-N, LM258-N, LM2904-N, LM358-N
www.ti.com
SNOSBT3H –JANUARY 2000–REVISED MARCH 2013
ELECTRICAL CHARACTERISTICS (continued)
V+ = +5.0V, See(1), unless otherwise stated
LM358
Typ
LM2904
Typ
Units
Parameter
Conditions
Min
Max
Min
Max
Large Signal Voltage Gain
V+ = +15V
(VO = 1V to 11V)
L ≥ 2 kΩ
VOH V+ = +30V
(LM2904, V+ = 26V)
15
15
V/mV
R
Output
RL = 2 kΩ
26
27
22
23
V
V
Voltage
RL = 10 kΩ
28
5
24
5
Swing
VOL V+ = 5V, RL = 10 kΩ
Source VIN+ = +1V, VIN− = 0V,
V+ = 15V, VO = 2V
20
100
mV
Output Current
10
5
20
8
10
5
20
8
mA
mA
Sink VIN− = +1V, VIN+ = 0V,
V+ = 15V, VO = 2V
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: LM158-N LM258-N LM2904-N LM358-N
LM158-N, LM258-N, LM2904-N, LM358-N
SNOSBT3H –JANUARY 2000–REVISED MARCH 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS
Input Voltage Range
Input Current
Figure 1.
Figure 2.
Supply Current
Voltage Gain
Figure 3.
Figure 4.
Open Loop Frequency Response
Common-Mode Rejection Ratio
Figure 5.
Figure 6.
8
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM158-N LM258-N LM2904-N LM358-N
LM158-N, LM258-N, LM2904-N, LM358-N
www.ti.com
SNOSBT3H –JANUARY 2000–REVISED MARCH 2013
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Voltage Follower Pulse Response
Voltage Follower Pulse Response (Small Signal)
Figure 7.
Figure 8.
Large Signal Frequency Response
Output Characteristics Current Sourcing
Figure 9.
Figure 10.
Output Characteristics Current Sinking
Current Limiting
Figure 11.
Figure 12.
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: LM158-N LM258-N LM2904-N LM358-N
LM158-N, LM258-N, LM2904-N, LM358-N
SNOSBT3H –JANUARY 2000–REVISED MARCH 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Input Current (LM2902 only)
Voltage Gain (LM2902 only)
Figure 13.
Figure 14.
10
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM158-N LM258-N LM2904-N LM358-N
LM158-N, LM258-N, LM2904-N, LM358-N
www.ti.com
SNOSBT3H –JANUARY 2000–REVISED MARCH 2013
APPLICATION HINTS
The LM158 series are op amps which operate with only a single power supply voltage, have true-differential
inputs, and remain in the linear mode with an input common-mode voltage of 0 VDC. These amplifiers operate
over a wide range of power supply voltage with little change in performance characteristics. At 25°C amplifier
operation is possible down to a minimum supply voltage of 2.3 VDC
.
Precautions should be taken to insure that the power supply for the integrated circuit never becomes reversed in
polarity or that the unit is not inadvertently installed backwards in a test socket as an unlimited current surge
through the resulting forward diode within the IC could cause fusing of the internal conductors and result in a
destroyed unit.
Large differential input voltages can be easily accommodated and, as input differential voltage protection diodes
are not needed, no large input currents result from large differential input voltages. The differential input voltage
may be larger than V+ without damaging the device. Protection should be provided to prevent the input voltages
from going negative more than −0.3 VDC (at 25°C). An input clamp diode with a resistor to the IC input terminal
can be used.
To reduce the power supply current drain, the amplifiers have a class A output stage for small signal levels which
converts to class B in a large signal mode. This allows the amplifiers to both source and sink large output
currents. Therefore both NPN and PNP external current boost transistors can be used to extend the power
capability of the basic amplifiers. The output voltage needs to raise approximately 1 diode drop above ground to
bias the on-chip vertical PNP transistor for output current sinking applications.
For ac applications, where the load is capacitively coupled to the output of the amplifier, a resistor should be
used, from the output of the amplifier to ground to increase the class A bias current and prevent crossover
distortion. Where the load is directly coupled, as in dc applications, there is no crossover distortion.
Capacitive loads which are applied directly to the output of the amplifier reduce the loop stability margin. Values
of 50 pF can be accommodated using the worst-case non-inverting unity gain connection. Large closed loop
gains or resistive isolation should be used if larger load capacitance must be driven by the amplifier.
The bias network of the LM158 establishes a drain current which is independent of the magnitude of the power
supply voltage over the range of 3 VDC to 30 VDC
.
Output short circuits either to ground or to the positive power supply should be of short time duration. Units can
be destroyed, not as a result of the short circuit current causing metal fusing, but rather due to the large increase
in IC chip dissipation which will cause eventual failure due to excessive function temperatures. Putting direct
short-circuits on more than one amplifier at a time will increase the total IC power dissipation to destructive
levels, if not properly protected with external dissipation limiting resistors in series with the output leads of the
amplifiers. The larger value of output source current which is available at 25°C provides a larger output current
capability at elevated temperatures (see TYPICAL PERFORMANCE CHARACTERISTICS) than a standard IC
op amp.
The circuits presented in the TYPICAL SINGLE-SUPPLY APPLICATIONS emphasize operation on only a single
power supply voltage. If complementary power supplies are available, all of the standard op amp circuits can be
used. In general, introducing a pseudo-ground (a bias voltage reference of V+/2) will allow operation above and
below this value in single power supply systems. Many application circuits are shown which take advantage of
the wide input common-mode voltage range which includes ground. In most cases, input biasing is not required
and input voltages which range to ground can easily be accommodated.
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: LM158-N LM258-N LM2904-N LM358-N
LM158-N, LM258-N, LM2904-N, LM358-N
SNOSBT3H –JANUARY 2000–REVISED MARCH 2013
www.ti.com
CONNECTION DIAGRAM
Figure 15. PDIP/CDIP/SOIC Package – Top View
(See Package Number P, NAB0008A, or D)
Figure 16. TO-99 Package – Top View
(See Package Number LMC)
Figure 17. 8-Bump DSBGA - Top View, Bump Side Down
(See Package Number YPB0008AAA)
TYPICAL SINGLE-SUPPLY APPLICATIONS
(V+ = 5.0 VDC
)
Figure 18. Non-Inverting DC Gain (0V Output)
*R not needed due to temperature
independent IIN
12
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM158-N LM258-N LM2904-N LM358-N
LM158-N, LM258-N, LM2904-N, LM358-N
www.ti.com
SNOSBT3H –JANUARY 2000–REVISED MARCH 2013
Where: VO = V1 + V2 − V3 − V4
(V1 + V2) ≥ (V3 + V4) to keep VO > 0 VDC
Figure 19. DC Summing Amplifier
(VIN'S ≥ 0 VDC and VO ≥ 0 VDC
)
VO = 0 VDC for VIN = 0 VDC
AV = 10
Figure 20. Power Amplifier
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: LM158-N LM258-N LM2904-N LM358-N
LM158-N, LM258-N, LM2904-N, LM358-N
SNOSBT3H –JANUARY 2000–REVISED MARCH 2013
www.ti.com
fo = 1 kHz
Q = 50
Av = 100 (40 dB)
Figure 21. “BI-QUAD” RC Active Bandpass Filter
Figure 22. Fixed Current Sources
Figure 23. Lamp Driver
14
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM158-N LM258-N LM2904-N LM358-N
LM158-N, LM258-N, LM2904-N, LM358-N
www.ti.com
SNOSBT3H –JANUARY 2000–REVISED MARCH 2013
Figure 24. LED Driver
*(Increase R1 for IL small)
L ≤ V+ −2V
V
Figure 25. Current Monitor
Figure 26. Driving TTL
VO = VIN
Figure 27. Voltage Follower
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: LM158-N LM258-N LM2904-N LM358-N
LM158-N, LM258-N, LM2904-N, LM358-N
SNOSBT3H –JANUARY 2000–REVISED MARCH 2013
www.ti.com
Figure 28. Pulse Generator
Figure 29. Squarewave Oscillator
Figure 30. Pulse Generator
HIGH ZIN
LOW ZOUT
Figure 31. Low Drift Peak Detector
16
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM158-N LM258-N LM2904-N LM358-N
LM158-N, LM258-N, LM2904-N, LM358-N
www.ti.com
SNOSBT3H –JANUARY 2000–REVISED MARCH 2013
IO = 1 amp/volt VIN
(Increase RE for IO small)
Figure 32. High Compliance Current Sink
Figure 33. Comparator with Hysteresis
*WIDE CONTROL VOLTAGE RANGE: 0 VDC ≤ VC ≤ 2 (V+ −1.5V DC
)
Figure 34. Voltage Controlled Oscillator (VCO)
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links: LM158-N LM258-N LM2904-N LM358-N
LM158-N, LM258-N, LM2904-N, LM358-N
SNOSBT3H –JANUARY 2000–REVISED MARCH 2013
www.ti.com
Figure 35. AC Coupled Inverting Amplifier
Figure 36. Ground Referencing a Differential Input Signal
Av = 11 (As Shown)
Figure 37. AC Coupled Non-Inverting Amplifier
18
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM158-N LM258-N LM2904-N LM358-N
LM158-N, LM258-N, LM2904-N, LM358-N
www.ti.com
SNOSBT3H –JANUARY 2000–REVISED MARCH 2013
fo = 1 kHz
Q = 1
AV = 2
Figure 38. DC Coupled Low-Pass RC Active Filter
fo = 1 kHz
Q = 25
Figure 39. Bandpass Active Filter
Figure 40. High Input Z, DC Differential Amplifier
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Links: LM158-N LM258-N LM2904-N LM358-N
LM158-N, LM258-N, LM2904-N, LM358-N
SNOSBT3H –JANUARY 2000–REVISED MARCH 2013
www.ti.com
Figure 41. Photo Voltaic-Cell Amplifier
Figure 42. Bridge Current Amplifier
Figure 43. High Input Z Adjustable-Gain DC Instrumentation Amplifier
20
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM158-N LM258-N LM2904-N LM358-N
LM158-N, LM258-N, LM2904-N, LM358-N
www.ti.com
SNOSBT3H –JANUARY 2000–REVISED MARCH 2013
Figure 44. Using Symmetrical Amplifiers to Reduce Input Current (General Concept)
SCHEMATIC DIAGRAM
(Each Amplifier)
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
21
Product Folder Links: LM158-N LM258-N LM2904-N LM358-N
LM158-N, LM258-N, LM2904-N, LM358-N
SNOSBT3H –JANUARY 2000–REVISED MARCH 2013
www.ti.com
REVISION HISTORY
Changes from Revision G (March 2013) to Revision H
Page
•
Changed layout of National Data Sheet to TI format .......................................................................................................... 21
22
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM158-N LM258-N LM2904-N LM358-N
PACKAGE OPTION ADDENDUM
www.ti.com
9-Aug-2013
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
LM158AH
ACTIVE
TO-99
TO-99
LMC
8
8
500
TBD
Call TI
Call TI
-55 to 125
-55 to 125
LM158AH
LM158AH/NOPB
ACTIVE
LMC
500
Green (RoHS POST-PLATE
& no Sb/Br)
Level-1-NA-UNLIM
LM158AH
LM158H
ACTIVE
ACTIVE
TO-99
TO-99
LMC
LMC
8
8
500
500
TBD
Call TI
Call TI
-55 to 125
-55 to 125
LM158H
LM158H
LM158H/NOPB
Green (RoHS POST-PLATE
& no Sb/Br)
Level-1-NA-UNLIM
LM158J
LM258H
ACTIVE
ACTIVE
ACTIVE
CDIP
TO-99
TO-99
NAB
LMC
LMC
8
8
8
40
TBD
Call TI
Call TI
Call TI
-55 to 125
-25 to 85
-25 to 85
LM158J
LM258H
LM258H
500
500
TBD
Call TI
LM258H/NOPB
Green (RoHS POST-PLATE
& no Sb/Br)
Level-1-NA-UNLIM
LM2904ITP/NOPB
LM2904ITPX/NOPB
LM2904M
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
DSBGA
DSBGA
SOIC
SOIC
SOIC
SOIC
PDIP
YPB
YPB
D
8
8
8
8
8
8
8
8
8
8
8
250
3000
95
Green (RoHS
& no Sb/Br)
SNAGCU
SNAGCU
Call TI
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Call TI
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
0 to 70
A
09
Green (RoHS
& no Sb/Br)
A
09
TBD
LM
2904M
LM2904M/NOPB
LM2904MX
D
95
Green (RoHS
& no Sb/Br)
CU SN
Call TI
Level-1-260C-UNLIM
Call TI
LM
2904M
D
2500
2500
40
TBD
LM
2904M
LM2904MX/NOPB
LM2904N
D
Green (RoHS
& no Sb/Br)
CU SN
Call TI
Level-1-260C-UNLIM
Call TI
LM
2904M
P
TBD
LM
2904N
LM2904N/NOPB
LM358AM
PDIP
P
40
Green (RoHS
& no Sb/Br)
CU SN
Call TI
Level-1-NA-UNLIM
Call TI
LM
2904N
SOIC
SOIC
SOIC
D
95
TBD
LM
358AM
LM358AM/NOPB
LM358AMX
D
95
Green (RoHS
& no Sb/Br)
CU SN
Call TI
Level-1-260C-UNLIM
Call TI
0 to 70
LM
358AM
D
2500
TBD
0 to 70
LM
358AM
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
9-Aug-2013
Orderable Device
Status Package Type Package Pins Package
Eco Plan Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
0 to 70
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
LM358AMX/NOPB
LM358AN
ACTIVE
SOIC
PDIP
PDIP
D
8
8
8
2500
Green (RoHS
& no Sb/Br)
CU SN
Call TI
CU SN
Call TI
Level-1-260C-UNLIM
LM
358AM
ACTIVE
ACTIVE
P
P
40
40
TBD
Call TI
0 to 70
LM
358AN
LM358AN/NOPB
Green (RoHS
& no Sb/Br)
Level-1-NA-UNLIM
0 to 70
LM
358AN
LM358H
ACTIVE
ACTIVE
TO-99
TO-99
LMC
LMC
8
8
500
500
TBD
Call TI
0 to 70
0 to 70
LM358H
LM358H/NOPB
Green (RoHS POST-PLATE
& no Sb/Br)
Level-1-NA-UNLIM
LM358H
LM358M
LM358M/NOPB
LM358MX
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
SOIC
SOIC
D
D
8
8
8
8
8
8
8
8
95
95
TBD
Call TI
CU SN
Call TI
Call TI
0 to 70
0 to 70
0 to 70
0 to 70
0 to 70
0 to 70
0 to 70
0 to 70
LM
358M
Green (RoHS
& no Sb/Br)
Level-1-260C-UNLIM
Call TI
LM
358M
SOIC
D
2500
2500
40
TBD
LM
358M
LM358MX/NOPB
LM358N
SOIC
D
Green (RoHS
& no Sb/Br)
CU SN
Call TI
Level-1-260C-UNLIM
Call TI
LM
358M
PDIP
P
TBD
LM
358N
LM358N/NOPB
LM358TP/NOPB
LM358TPX/NOPB
PDIP
P
40
Green (RoHS
& no Sb/Br)
CU SN
SNAGCU
SNAGCU
Level-1-NA-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
LM
358N
DSBGA
DSBGA
YPB
YPB
250
3000
Green (RoHS
& no Sb/Br)
A
07
Green (RoHS
& no Sb/Br)
A
07
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
9-Aug-2013
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
8-Apr-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LM2904ITP/NOPB
LM2904ITPX/NOPB
LM2904MX
DSBGA
DSBGA
SOIC
YPB
YPB
D
8
8
8
8
8
8
8
8
8
8
250
3000
2500
2500
2500
2500
2500
2500
250
178.0
178.0
330.0
330.0
330.0
330.0
330.0
330.0
178.0
178.0
8.4
8.4
1.5
1.5
6.5
6.5
6.5
6.5
6.5
6.5
1.5
1.5
1.5
1.5
5.4
5.4
5.4
5.4
5.4
5.4
1.5
1.5
0.66
0.66
2.0
4.0
4.0
8.0
8.0
8.0
8.0
8.0
8.0
4.0
4.0
8.0
8.0
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
12.4
12.4
12.4
12.4
12.4
12.4
8.4
12.0
12.0
12.0
12.0
12.0
12.0
8.0
LM2904MX/NOPB
LM358AMX
SOIC
D
2.0
SOIC
D
2.0
LM358AMX/NOPB
LM358MX
SOIC
D
2.0
SOIC
D
2.0
LM358MX/NOPB
LM358TP/NOPB
LM358TPX/NOPB
SOIC
D
2.0
DSBGA
DSBGA
YPB
YPB
0.66
0.66
3000
8.4
8.0
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
8-Apr-2013
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
LM2904ITP/NOPB
LM2904ITPX/NOPB
LM2904MX
DSBGA
DSBGA
SOIC
YPB
YPB
D
8
8
8
8
8
8
8
8
8
8
250
3000
2500
2500
2500
2500
2500
2500
250
210.0
210.0
367.0
367.0
367.0
367.0
367.0
367.0
210.0
210.0
185.0
185.0
367.0
367.0
367.0
367.0
367.0
367.0
185.0
185.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
LM2904MX/NOPB
LM358AMX
SOIC
D
SOIC
D
LM358AMX/NOPB
LM358MX
SOIC
D
SOIC
D
LM358MX/NOPB
LM358TP/NOPB
LM358TPX/NOPB
SOIC
D
DSBGA
DSBGA
YPB
YPB
3000
Pack Materials-Page 2
MECHANICAL DATA
NAB0008A
J08A (Rev M)
www.ti.com
MECHANICAL DATA
YPB0008
D
0.5±0.045
E
TPA08XXX (Rev A)
D: Max = 1.337 mm, Min =1.276 mm
E: Max = 1.337 mm, Min =1.276 mm
4215100/A
12/12
A. All linear dimensions are in millimeters. Dimensioning and tolerancing per ASME Y14.5M-1994.
B. This drawing is subject to change without notice.
NOTES:
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明