LM3526MX-L [TI]
2 通道、0.5A 负载、2.7-5.5V、100mΩ USB 电源开关 | D | 8 | -40 to 125;型号: | LM3526MX-L |
厂家: | TEXAS INSTRUMENTS |
描述: | 2 通道、0.5A 负载、2.7-5.5V、100mΩ USB 电源开关 | D | 8 | -40 to 125 开关 驱动 电源开关 光电二极管 接口集成电路 |
文件: | 总21页 (文件大小:1412K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LM3526
www.ti.com
SNVS054E –FEBRUARY 2000–REVISED MARCH 2013
LM3526 Dual Port USB Power Switch and Over-Current Protection
Check for Samples: LM3526
1
FEATURES
DESCRIPTION
The LM3526 provides Universal Serial Bus standard
power switch and over-current protection for all host
port applications. The dual port device is ideal for
Notebook and desktop PC's that supply power to
more than one port.
2
•
•
•
Compatible with USB1.1 and USB 2.0
1 ms Fault Flag Delay Filters Hot-Plug Events
Smooth Turn-on Eliminates In-rush Induced
Voltage Drop
•
•
UL Recognized Component: REF# 205202
A 1 ms delay on the fault flag output prevents
erroneous overcurrent reporting caused by in-rush
currents during hot-plug events.
1A Nominal Short Circuit Output Current
Protects PC Power Supplies
•
Thermal Shutdown Protects Device in Direct
Short Condition
The dual stage thermal protection circuit in the
LM3526 provides individual protection to each switch
and the entire device. In a short-circuit/over-current
event, the switch dissipating excessive heat is turned
off, allowing the second switch to continue to function
uninterrupted.
•
•
•
•
•
•
•
500mA Minimum Continuous Load Current
Small SOIC-8 package minimizes board space
2.7V to 5.5V Input Voltage Range
140 mΩ Max. Switch Resistance
1 µA Max. Standby Current
The LM3526 accepts an input voltage between 2.7V
and 5.5V allowing use as a device-based in-rush
current limiter for 3.3V USB peripherals, as well as
Root and Self-Powered Hubs at 5.5V. The Enable
inputs accept both 3.3V and 5.0V logic thresholds.
200 µA Max. Operating Current
Under-voltage Lockout (UVLO)
The small size, low RON, and 1 ms fault flag delay
make the LM3526 a good choice for root hubs as well
as per-port power control in embedded and stand-
alone hubs.
APPLICATIONS
•
Universal Serial Bus (USB) Root Hubs
including Desktop and Notebook PC
•
•
•
USB Monitor Hubs
Other Self-Powered USB Hub Devices
High Power USB Devices Requiring In-rush
Limiting
•
General Purpose High Side Switch
Applications
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2000–2013, Texas Instruments Incorporated
LM3526
SNVS054E –FEBRUARY 2000–REVISED MARCH 2013
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Typical Operating Circuit and Connection Diagram
Figure 1. LM3526-H
Figure 2. LM3526-L
2
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3526
LM3526
www.ti.com
SNVS054E –FEBRUARY 2000–REVISED MARCH 2013
Absolute Maximum Ratings(1)(2)
Supply Voltage
−0.3V to 6V
−0.3V to 6V
−0.3V to 5.5V
700 mW
Output Voltage
Voltage at All Other Pins
Power Dissipation (TA = 25°C)(3)
(3)
TJMAX
150°C
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Electrical specifications do not apply when
operating the device beyond its rated operating conditions.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
(3) The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX (Maximum junction temperature),
θJA (junction to ambient thermal resistance), and TA (ambient temperature). The maximum allowable power dissipation at any
temperature is PDMAX = (TJMAX − TA)/θJA or the number given in the Absolute Maximum Ratings, which ever is lower. θJA = 150°C/W.
Operating Ratings
Supply Voltage Range
2.7V to 5.5V
−40°C to 85°C
−40°C to 125°C
−65°C to +150°C
260°C
Operating Ambient Range
Operating Junction Temperature Range
Storage Temperature Range
Lead Temperature (Soldering, 5 seconds)
ESD Rating(1)
2kV
ESD Rating Output Only
8kV
(1) The human body model is a 100 pF capacitor discharged through a 1.5 kΩ resistor into each pin. Enable pin ESD threshold is 1.7kV.
DC Electrical Characteristics
Limits in standard typeface are for TJ = 25°C, and limits in boldface type apply over the full operating temperature range.
Unless otherwise specified: VIN = 5.0V, VEN = 0V (LM3526-L) or VEN = VIN (LM3526-H).
Symbol
RON
IOUT
ISC
Parameter
Conditions
Min
Typ
100
110
Max
140
180
Units
mΩ
A
VIN = 5V, IOUT = 500mA, each switch
VIN = 2.7V, IOUT = 500mA, each switch
On Resistance
OUT pins continuous output Each Output
current
Short Circuit Output Current Each Output (enable into Load)(1)
0.5
A
VOUT = 4.0V
VOUT = 0.1V
0.5
1.2
1
1.9
1.5
3.2
10
OCTHRESH
ILEAK
Over-current Threshold
2.2
0.01
A
OUT pins Output Leakage
Current
VEN = VIN (LM3526-L)
VEN = 0V (LM3526-H)
µA
IFO = 10 mA, VIN = 5.0V
IFO = 10 mA, VIN = 3.3V
IFO = 10 mA, VIN = 2.7V
VEN/VEN = 0V or VEN/VEN = VIN
See(2)
10
11
12
25
35
40
0.5
RFO
FLAG Output Resistance
Ω
IEN
EN/EN Leakage Current
EN/EN Input Logic High
EN/EN Input Logic Low
−0.5
µA
V
VIH
2.4
1.9
1.7
1.8
VIL
See(2)
0.8
V
VUVLO
Under-Voltage Lockout
Threshold
V
IDDOFF
Supply Current
Switch-Off
0.2
1
µA
−40°C ≤ TJ ≤ 85°C
2
IDDON
ThSD
Supply Current
Switch-On
115
200
µA
°C
Over-temperature Shutdown TJ Increasing, with no shorted output
Threshold
150
145
135
TJ Increasing, with shorted output (s)
TJ Decreasing(1)
(1) Thermal Shutdown will protect the device from permanent damage.
(2) For LM3526-L, OFF is EN ≥ 2.4V and ON is EN ≤ 0.8V. For LM3526-H, OFF is EN ≤ 0.8V and ON is EN ≥ 2.4V.
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LM3526
LM3526
SNVS054E –FEBRUARY 2000–REVISED MARCH 2013
www.ti.com
DC Electrical Characteristics (continued)
Limits in standard typeface are for TJ = 25°C, and limits in boldface type apply over the full operating temperature range.
Unless otherwise specified: VIN = 5.0V, VEN = 0V (LM3526-L) or VEN = VIN (LM3526-H).
Symbol
IFH
Parameter
Conditions
Min
Typ
Max
Units
Error Flag Leakage Current Vflag = 5V
0.01
1
µA
AC Electrical Characteristics
Limits in standard typeface are for TJ = 25°C, and limits in boldface type apply over the full operating temperature range.
Unless otherwise specified: VIN = 5.0V.
Symbol
Parameter
OUT Rise Time
Conditions
Min
Typ
100
5
Max
Units
µs
tr
RL = 10Ω
RL = 10Ω
RL = 10Ω
RL = 10Ω
RL = 0
tf
OUT Fall Time
µs
tON
Turn on Delay, EN to OUT
Turn off Delay, EN to OUT
Over Current Flag Delay
150
5
µs
tOFF
tOC
µs
1
ms
TYPICAL APPLICATION CIRCUIT
PIN DESCRIPTIONS
Pin Number
Pin Name
Pin Function
1, 4
ENA, ENB
(LM3526-L)
ENA, ENB
(LM3526-H)
Enable (Input): Logic-compatible enable inputs.
2, 3
FLAG A
FLAG B
Fault Flag (Output): Active-low, open-drain outputs. Indicates overcurrent, UVLO or thermal shutdown.
*See Application Information for more information.
6
7
GND
IN
Ground
Supply Input: This pin is the input to the power switch and the supply voltage for the IC.
Switch Output: These pins are the outputs of the high side switch.
8, 5
OUT A
OUT B
Figure 3. Typical Application Circuit
4
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3526
LM3526
www.ti.com
SNVS054E –FEBRUARY 2000–REVISED MARCH 2013
Typical Performance Characteristics
VIN = 5.0V, IL = 500 mA, TA = 25°C unless otherwise specified.
RON
vs
Temperature
RON
vs
Temperature
Figure 4.
Figure 5.
Quiescent Current
vs
Input Voltage
Quiescent Current
vs
Temperature
Figure 6.
Figure 7.
Current Limit
vs
Output Voltage
OC Threshold
vs
Temperature
Figure 8.
Figure 9.
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: LM3526
LM3526
SNVS054E –FEBRUARY 2000–REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics (continued)
VIN = 5.0V, IL = 500 mA, TA = 25°C unless otherwise specified.
Fault Flag Delay
Fault Flag Delay
vs
Temperature
vs
Temperature
Figure 10.
Figure 11.
Under Voltage Lockout Threshold
vs
Under Voltage Lockout (UVLO)
Temperature
Figure 12.
Figure 13.
Short Circuit Response with
Thermal Cycling*
Over Current/Current Limit Response*
* Output is shorted to Ground through a 100 mΩ resistor
Figure 14.
Figure 15.
6
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3526
LM3526
www.ti.com
SNVS054E –FEBRUARY 2000–REVISED MARCH 2013
Typical Performance Characteristics (continued)
VIN = 5.0V, IL = 500 mA, TA = 25°C unless otherwise specified.
Turn-ON/OFF Response with
Turn-ON/OFF Response with
47Ω/10µF Load
47Ω/150µF Load
Figure 16.
Figure 17.
Thermal Shutdown Response
(Port A output shorted*)
Thermal Shutdown Response (See Notes)
* Port A is shorted to GND through a 100 mΩ resistor
Figure 18.
Figure 19.
Enable into a short
Figure 20.
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: LM3526
LM3526
SNVS054E –FEBRUARY 2000–REVISED MARCH 2013
www.ti.com
FUNCTIONAL DESCRIPTION
The LM3526-H and LM3526-L are high side P-Channel switches with active-high and active-low enable inputs,
respectively. Fault conditions turn-off and inhibit turn-on of the output transistor and activate the open-drain error
flag transistor sinking current to the ground.
INPUT AND OUTPUT
IN (Input) is the power supply connection to the control circuitry and the source of the output MOSFET.
OUT (Output) is the connection to the drain of the output MOSFET. In a typical application circuit, current flows
through the switch from IN to OUT towards the load.
If VOUT is greater than VIN when the switch is enabled, current will flow from OUT to IN since the MOSFET is
bidirectional.
THERMAL SHUTDOWN
The LM3526 is internally protected against excessive power dissipation by a two-stage thermal protection circuit.
If the device temperature rises to approximately 145°C, the thermal shutdown circuitry turns off any switch that is
current limited. Non-overloaded switches continue to function normally. If the die temperature rises above 150°C,
both switches are turned off and both fault flag outputs are activated. Hysteresis ensures that a switch turned off
by thermal shutdown will not be turned on again until the die temperature is reduced to 135°C. Shorted switches
will continue to cycle off and on, due to the rising and falling die temperature, until the short is removed.
UNDERVOLTAGE LOCKOUT
UVLO prevents the MOSFET switch from turning on until input voltage exceeds 1.8V (typical).
If input voltage drops below 1.8V (typical), UVLO shuts off the MOSFET switch and signals the fault flag. UVLO
functions only when device is enabled.
CURRENT LIMIT
The current limit circuit is designed to protect the system supply, the MOSFET switches and the load from
damage caused by excessive currents. The current limit threshold is set internally to allow a minimum of 500 mA
through the MOSFET but limits the output current to approximately 1.0A typical.
FAULT FLAG
The fault flag is an open-drain output capable of sinking 10 mA load current to typically 100 mV above ground.
A parasitic diode exists between the flag pins and VIN pin. Pulling the flag pins to voltages higher than VIN will
forward bias this diode and will cause an increase in supply current. This diode will also clamp the voltage on the
flag pins to a diode drop above VIN.
The fault flag is active (pulled low) when any of the following conditions are present: under-voltage, current limit,
or thermal shutdown.
A 1ms (typ.) delay in reporting the fault condition prevents erroneous fault flags and eliminates the need for an
external RC delay network.
Application Information
FILTERING
The USB specification indicates that “no less than 120 µF tantalum capacitors” must be used on the output of
each downstream port. This bulk capacitance provides the short-term transient current needed during a hot plug-
in. Current surges caused by the input capacitance of the down stream device could generate undesirable EMI
signals. Ferrite beads in series with all power and ground lines are recommended to eliminate or significantly
reduce EMI.
In selecting a ferrite bead, the DC resistance of the wire used must be kept to a minimum to reduce the voltage
drop.
8
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3526
LM3526
www.ti.com
SNVS054E –FEBRUARY 2000–REVISED MARCH 2013
A 0.01 µF ceramic capacitor is recommended on each port directly between the Vbus and ground pins to prevent
EMI damage to other components during the hot-detachment.
Adequate capacitance must be connected to the input of the device to limit the input voltage drop during a hot-
plug event to less than 330 mV. For a few tens of µs, the host must supply the in-rush current to the peripheral,
charging its bulk capacitance to Vbus. This current is initially supplied by the input capacitor. A 33 µF 16V
tantalum capacitor is recommended.
In choosing the capacitors, special attention must be paid to the Effective Series Resistance, ESR, of the
capacitors to minimize the IR drop across the capacitor's ESR.
SOFT START
To eliminate the upstream voltage droop caused by the high in-rush current drawn by the output capacitors, the
maximum in-rush current is internally limited to 1.5A.
TRANSIENT OVER-CURRENT DELAY
High transient current is also generated when the switch is enabled and large values of capacitance at the output
have to be rapidly charged. The in-rush currents created could exceed the short circuit current limit threshold of
the device forcing it into the current limit mode. The capacitor is charged with the maximum available short circuit
current set by the LM3526. The duration of the in-rush current depends on the size of the output capacitance and
load current. Since this is not a valid fault condition, the LM3526 delays the generation of the fault flag for 1 ms.
If the condition persists due to other causes such as a short, a fault flag is generated after a 1 ms delay has
elapsed.
The LM3526's 1 ms delay in issuing the fault flag is adequate for most applications. If longer delays are required,
an RC filter as shown in Figure 21 may be used.
Figure 21.
PCB LAYOUT CONSIDERATIONS
In order to meet the USB requirements for voltage drop, droop and EMI, each component used in this circuit
must be evaluated for its contribution to the circuit performance. The PCB layout rules and guidelines must be
followed.
•
Place the switch as close to the USB connector as possible. Keep all Vbus traces as short as possible and use
at least 50-mil, 1 ounce copper for all Vbus traces. Solder plating the traces will reduce the trace resistance.
•
Avoid vias as much as possible. If vias are used, use multiple vias in parallel and/or make them as large as
possible.
•
•
Place the output capacitor and ferrite beads as close to the USB connector as possible.
If ferrite beads are used, use wires with minimum resistance and large solder pads to minimize connection
resistance.
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: LM3526
LM3526
SNVS054E –FEBRUARY 2000–REVISED MARCH 2013
www.ti.com
Figure 22. Self-Powered Hub Per-Port Voltage Drop
Typical Applications
Figure 23. Dual-Port USB Self-Powered Hub
Figure 24. Soft-Start Application (Single port shown)
10
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3526
LM3526
www.ti.com
SNVS054E –FEBRUARY 2000–REVISED MARCH 2013
Figure 25. In-rush Current-limit Application
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: LM3526
LM3526
SNVS054E –FEBRUARY 2000–REVISED MARCH 2013
www.ti.com
REVISION HISTORY
Changes from Revision D (March 2013) to Revision E
Page
•
Changed layout of National Data Sheet to TI format .......................................................................................................... 11
12
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3526
PACKAGE OPTION ADDENDUM
www.ti.com
30-Sep-2021
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
95
95
95
95
(1)
(2)
(3)
(4/5)
(6)
LM3526M-H
LM3526M-H/NOPB
LM3526M-L
ACTIVE
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
D
D
D
D
D
D
D
8
8
8
8
8
8
8
Non-RoHS
& Green
Call TI
Level-1-235C-UNLIM
Level-1-260C-UNLIM
Level-1-235C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-235C-UNLIM
Level-1-260C-UNLIM
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
3526
M-H
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
RoHS & Green
SN
Call TI
SN
3526
M-H
Non-RoHS
& Green
3526
M-L
LM3526M-L/NOPB
LM3526MX-H/NOPB
LM3526MX-L
RoHS & Green
3526
M-L
2500 RoHS & Green
SN
3526
M-H
2500
Non-RoHS
& Green
Call TI
SN
3526
M-L
LM3526MX-L/NOPB
2500 RoHS & Green
3526
M-L
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
30-Sep-2021
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
5-Jan-2022
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LM3526MX-H/NOPB
LM3526MX-L
SOIC
SOIC
SOIC
D
D
D
8
8
8
2500
2500
2500
330.0
330.0
330.0
12.4
12.4
12.4
6.5
6.5
6.5
5.4
5.4
5.4
2.0
2.0
2.0
8.0
8.0
8.0
12.0
12.0
12.0
Q1
Q1
Q1
LM3526MX-L/NOPB
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
5-Jan-2022
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
LM3526MX-H/NOPB
LM3526MX-L
SOIC
SOIC
SOIC
D
D
D
8
8
8
2500
2500
2500
367.0
367.0
367.0
367.0
367.0
367.0
35.0
35.0
35.0
LM3526MX-L/NOPB
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
5-Jan-2022
TUBE
*All dimensions are nominal
Device
Package Name Package Type
Pins
SPQ
L (mm)
W (mm)
T (µm)
B (mm)
LM3526M-H
LM3526M-H
D
D
D
D
D
D
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
8
8
8
8
8
8
95
95
95
95
95
95
495
495
495
495
495
495
8
8
8
8
8
8
4064
4064
4064
4064
4064
4064
3.05
3.05
3.05
3.05
3.05
3.05
LM3526M-H/NOPB
LM3526M-L
LM3526M-L
LM3526M-L/NOPB
Pack Materials-Page 3
PACKAGE OUTLINE
D0008A
SOIC - 1.75 mm max height
SCALE 2.800
SMALL OUTLINE INTEGRATED CIRCUIT
C
SEATING PLANE
.228-.244 TYP
[5.80-6.19]
.004 [0.1] C
A
PIN 1 ID AREA
6X .050
[1.27]
8
1
2X
.189-.197
[4.81-5.00]
NOTE 3
.150
[3.81]
4X (0 -15 )
4
5
8X .012-.020
[0.31-0.51]
B
.150-.157
[3.81-3.98]
NOTE 4
.069 MAX
[1.75]
.010 [0.25]
C A B
.005-.010 TYP
[0.13-0.25]
4X (0 -15 )
SEE DETAIL A
.010
[0.25]
.004-.010
[0.11-0.25]
0 - 8
.016-.050
[0.41-1.27]
DETAIL A
TYPICAL
(.041)
[1.04]
4214825/C 02/2019
NOTES:
1. Linear dimensions are in inches [millimeters]. Dimensions in parenthesis are for reference only. Controlling dimensions are in inches.
Dimensioning and tolerancing per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed .006 [0.15] per side.
4. This dimension does not include interlead flash.
5. Reference JEDEC registration MS-012, variation AA.
www.ti.com
EXAMPLE BOARD LAYOUT
D0008A
SOIC - 1.75 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT
8X (.061 )
[1.55]
SYMM
SEE
DETAILS
1
8
8X (.024)
[0.6]
SYMM
(R.002 ) TYP
[0.05]
5
4
6X (.050 )
[1.27]
(.213)
[5.4]
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:8X
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
METAL
EXPOSED
METAL
EXPOSED
METAL
.0028 MAX
[0.07]
.0028 MIN
[0.07]
ALL AROUND
ALL AROUND
SOLDER MASK
DEFINED
NON SOLDER MASK
DEFINED
SOLDER MASK DETAILS
4214825/C 02/2019
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
D0008A
SOIC - 1.75 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT
8X (.061 )
[1.55]
SYMM
1
8
8X (.024)
[0.6]
SYMM
(R.002 ) TYP
[0.05]
5
4
6X (.050 )
[1.27]
(.213)
[5.4]
SOLDER PASTE EXAMPLE
BASED ON .005 INCH [0.125 MM] THICK STENCIL
SCALE:8X
4214825/C 02/2019
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2022, Texas Instruments Incorporated
相关型号:
LM3528
High Efficiency, Multi Display LED Driver with 128 Exponential Dimming Steps and Integrated OLED Power Supply in a 1.2mm × 1.6mm μSMD Package
NSC
LM3528TME
IC LED DISPLAY DRIVER, PBGA12, 1.20 X 1.60 MM, 0.60 MM HEIGHT, MICRO, SMD-12, Display Driver
NSC
LM3528TMX
IC LED DISPLAY DRIVER, PBGA12, 1.20 X 1.60 MM, 0.60 MM HEIGHT, MICRO, SMD-12, Display Driver
NSC
©2020 ICPDF网 联系我们和版权申明