LM3543M-H/NOPB [TI]
IC,POWER SUPPLY SWITCHING CIRCUIT,CMOS,SOP,16PIN,PLASTIC;
| 型号： | LM3543M-H/NOPB |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | IC,POWER SUPPLY SWITCHING CIRCUIT,CMOS,SOP,16PIN,PLASTIC 开关 光电二极管 |
| 文件： | 总16页 (文件大小：528K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
OBSOLETE
LM3543
www.ti.com
SNVS065E –AUGUST 2000–REVISED MARCH 2013
LM3543 Triple Port USB Power Distribution Switch and Over-Current Protection
Check for Samples: LM3543
1
FEATURES
DESCRIPTION
The LM3543 is a triple high-side power switch that is
an excellent choice for use in Root, Self-Powered and
Bus-Powered USB (Universal Serial Bus) Hubs.
Independent port enables, flag signals to alert USB
controllers of error conditions, controlled start-up in
hot-plug events, and short circuit protection all satisfy
USB requirements.
2
•
Compatible with USB1.1 and USB 2.0
90mΩ (typ.) High-Side MOSFET Switch
500mA Continuous Current per Port
7 ms Fault Flag Delay Filters Hot-Plug Events
Industry Standard Pin Order
•
•
•
•
•
Short Circuit Protection with Power-Saving
Current Foldback
The LM3543 accepts input voltages between 2.7V
and 5.5V. The Enable logic inputs, available in active-
high and active-low versions, can be powered off any
voltage in the 2.7V to 5.5V range. The LM3543 limits
the continuous current through a single port to 1.25A
(max.) when it is shorted to ground.
•
•
•
•
•
•
•
Thermal Shutdown Protection
Undervoltage Lockout
Recognized by UL and Nemko
Input Voltage Range: 2.7V to 5.5V
5 µA Maximum Standby Supply Current
16-Pin SOIC Package
The low on-state resistance of the LM3543 switches
ensures the LM3543 will satisfy USB voltage drop
requirements, even when current through a switch
reaches 500 mA. Thus, High-Powered USB
Functions, Low-Powered USB Functions, and Bus-
Powered USB Hubs can all be powered off a Root or
Self-Powered USB Hub containing the LM3543.
Ambient Temperature Range: −40°C to 85°C
APPLICATIONS
•
USB Root, Self-Powered, and Bus-Powered
Hubs
Added features of the LM3543 include current
foldback to reduce power consumption in current
overload conditions, thermal shutdown to prevent
device failure caused by high-current overheating,
and undervoltage lockout to keep switches from
operating if the input voltage is below acceptable
levels.
•
•
USB Devices such as Monitors and Printers
General Purpose High Side Switch
Applications
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2000–2013, Texas Instruments Incorporated
OBSOLETE
LM3543
SNVS065E –AUGUST 2000–REVISED MARCH 2013
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Functional Diagram
Connection Diagram
Figure 1. 16-Pin SOIC
Figure 2. 16-Pin SOIC
Top View
Top View
2
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3543
OBSOLETE
LM3543
www.ti.com
SNVS065E –AUGUST 2000–REVISED MARCH 2013
Typical Application Circuit
Figure 3. The LM3543 used in a Self-Powered or Root USB Hub
Absolute Maximum Ratings(1)(2)
Voltage at INX and OUTX pins
Voltage at ENX(ENX) and FLAGX pins
Power Dissipation(3)
−0.3V to 6V
−0.3V to 5.5V
Internally Limited
150°C
Maximum Junction Temperature
Storage Temperature Range
Lead Temperature Range (Soldering, 5 sec.)
ESD Rating(4)
−65°C to 150°C
260°C
2 kV
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Electrical specifications do not apply when
operating the device beyond its rated operating conditions.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
(3) The maximum allowable power dissipation is a function of the Maximum Junction Temperature (TJMAX), Junction to Ambient Thermal
Resistance (θJA), and the Ambient Temperature (TA). The LM3543 in the 16-pin SOIC package has a TJMAX of 150°C and a θJA of
130°C/W. The maximum allowable power dissipation at any temperature is PMAX = (TJMAX − TA)/θJA. Exceeding the maximum allowable
power dissipation will cause excessive die temperature, and the part will go into thermal shutdown.
(4) The Human body model is a 100 pF capacitor discharged through a 1.5 kΩ resistor into each pin.
Operating Ratings
Supply Voltage Range
2.7V to 5.5V
0 mA to 500 mA
−40°C to 125°C
Continuous Output Current Range (Each Output)
Junction Temperature Range
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LM3543
OBSOLETE
LM3543
SNVS065E –AUGUST 2000–REVISED MARCH 2013
www.ti.com
DC Electrical Characteristics
Limits in standard typeface are for TJ = 25°C, and limits in boldface type apply over the full operating temperature range.
Unless otherwise specified: VIN = 5.0V, ENX = VIN (LM3543-H) or ENX = 0V (LM3543-L).
Symbol
Parameter
Conditions
VIN = 5V, IOUTX = 0.5A
VIN = 3.3V, IOUTX = 0.5A
3.0V ≤ VIN ≤ 5.5V
Min
Typ
90
Max
125
130
Units
RON
IOUT
On Resistance
mΩ
95
OUTX Continuous Output Current
OUTX Leakage Current
0.5
A
ILEAK-OUT
ENX = 0 (ENX = VIN);
TJ = 25°C
0.01
1
µA
ENX = 0 (ENX = VIN);
10
µA
− 40 ≤ TJ ≤ 85°C
ISC
OUTX Short-Circuit Current(1)
Overcurrent Threshold
OUTX Connected to GND
0.8
2.0
0.1
0.2
1.25
3.2
0.3
1
A
A
OCTHRESH
VL_FLAG
ILEAK-FLAG
ILEAK-EN
FLAGX Output-Low Voltage
FLAGX Leakage Current
ENx Input Leakage Current
I(FLAGX) = 10 mA
V
2.7 ≤ VFLAG ≤ 5.5V
µA
µA
ENx/ENx = 0V or
ENx/ENx = VIN
−0.5
0.5
VIH
VIL
EN/EN Input Logic High
EN/EN Input Logic Low
2.7V ≤ VIN ≤ 5.5V
4.5V ≤ VIN ≤ 5.5V
2.7V ≤ VIN ≤ 4.5V
2.4
V
V
0.8
0.4
VUVLO
Under-Voltage Lockout Threshold
Operational Supply Current
1.8
V
ENx = VIN (ENx = 0 );
TJ = 25°C
375
600
800
1
µA
IDDON
ENx = VIN (ENx = 0 );
−40°C ≤ TJ ≤ 125°C
µA
µA
µA
ENx = 0 (ENx = VIN);
TJ = 25°C
IDDOFF
Shutdown Supply Current
−40°C ≤ TJ ≤ 125°C
5
(1) Thermal Shutdown will protect the device from permanent damage.
4
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3543
OBSOLETE
LM3543
www.ti.com
SNVS065E –AUGUST 2000–REVISED MARCH 2013
AC Electrical Characteristics
Limits are for TJ = 25°C and VIN = 5.0V.
Symbol
Parameter
OUTx Rise Time(1)
OUTx Fall Time(2)
Turn-on Delay(3)
Turn-off Delay(4)
Flag Delay(5)
Conditions
CL = 33 µF, ILOAD = 500mA
CL = 33 µF, ILOAD = 500mA
CL = 33 µF, ILOAD = 500mA
CL = 33 µF, ILOAD = 500mA
IFLAG = 10 mA
Min
Typ
1.5
0.9
2.9
0.7
7
Max
Units
ms
tr
tf
ms
tON
tOFF
tF
ms
ms
ms
(1) Time for OUTx to rise from 10% to 90% of its enabled steady-state value after ENx (ENx) is asserted.
(2) Time for OUTx to fall from 10% to 90% of its enabled steady-state value after ENx (ENx) is deasserted.
(3) Time between ENx rising through VIH (ENx falling through VIL) and OUTx rising through 90% of its enabled steady-state voltage.
(4) Time between ENx falling through VIL (ENx rising through VIH) and OUTx falling through 10% of its enabled steady-state voltage.
(5) Time between ENx rising through VIN (ENx falling through VIN) and FLAGX falling through 0.3V when OUTX is connected to GND.
PIN DESCRIPTIONS
Pin Number
Pin Name
Pin Function
2, 6
IN 1, 2
Supply Inputs: These pins are the inputs to the power switches and the supply input for
the IC. In most applications they are connected together externally and to a single input
voltage supply.
1, 5
GND 1, 2
Grounds: Must be connected together and to a common ground.
Switch Outputs: These pins are the outputs of the high side switches.
Enable (Inputs): Active-high (or active-low) logic enable inputs.
15, 14, 11
3, 4, 7
OUT 1, 2, 3
LM3543-H: EN 1, 2, 3
LM3543-L: EN 1, 2, 3
16, 13, 12
8, 9, 10
FLAG 1, 2, 3
Fault Flag (Outputs): Active-low open drain outputs. Indicates over-current, UVLO or
thermal shutdown.
N/C
No Internal Connection.
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: LM3543
OBSOLETE
LM3543
SNVS065E –AUGUST 2000–REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics
VIN = 5.0, IOUT_X = 500mA, TA = 25°C unless otherwise specified.
RON vs Input Voltage
RON vs Junction Temperature
Figure 4.
Figure 5.
Quiescent Current, Output(s) Enabled
Quiescent Current, Output(s) Disabled
vs
vs
Junction Temperature
Junction Temperature
Figure 6.
Figure 7.
Quiescent Current, Output(s) Enabled
Quiescent Current, Output(s) Disabled
vs
vs
Input Voltage
Input Voltage
Figure 8.
Figure 9.
6
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3543
OBSOLETE
LM3543
www.ti.com
SNVS065E –AUGUST 2000–REVISED MARCH 2013
Typical Performance Characteristics (continued)
VIN = 5.0, IOUT_X = 500mA, TA = 25°C unless otherwise specified.
Short-Circuit Output Current
Over-Current Threshold
vs
Junction Temperature
vs
Junction Temperature
Output is shorted to Ground through a 100 mΩ resistor.
Output is shorted to Ground through a 100 mΩ resistor.
Figure 10.
Figure 11.
Turn-On Delay
vs
Under-Voltage Lockout (UVLO) Threshold
vs
Input Voltage
Junction Temperature
(CIN = 33 µF, COUT = 33 µF)
Figure 12.
Figure .
Turn-Off Delay
vs
Fault Flag Delay Time
vs
Junction Temperature
Input Voltage
(CIN = 33 µF, COUT = 33 µF)
Figure 13.
Figure 14.
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: LM3543
OBSOLETE
LM3543
SNVS065E –AUGUST 2000–REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics (continued)
VIN = 5.0, IOUT_X = 500mA, TA = 25°C unless otherwise specified.
Turn-On/Turn-Off Response with 47Ω/33µF Load
Turn-On/Turn-Off Response with 10Ω/33µF Load
Figure 15.
Figure 16.
Enable Into a Short
Short Connected to Enabled Device
Output is shorted to Ground through a 100 mΩ resistor.
Output is shorted to Ground through a 100 mΩ resistor.
Figure 17.
Figure 18.
Inrush Current to Downstream Device
when LM3543 is Enabled
Over-Current Response with Ramped Load on OUT1 and
Fixed Load on OUT2
Output is shorted to Ground through a 100 mΩ resistor.
Load is two capacitors and one resistor in parallel to model an actual
USB load condition. The first capacitor has a value of 33 µF to model
the LM3543 output capacitor. The second capacitor has a value of 10
µF to model the maximum allowable input capacitance of the
downstream device. The resistor is a 47Ω resistor to model the
maximum allowable input resistance of the downstream device.
Figure 19.
Figure 20.
8
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3543
OBSOLETE
LM3543
www.ti.com
SNVS065E –AUGUST 2000–REVISED MARCH 2013
FUNCTIONAL DESCRIPTIONS
POWER SWITCHES
The power switches that comprise the three ports of the LM3543 are N-Channel MOSFETs. They have a typical
on-state drain-to-source resistance of 90 mΩ when the input voltage is 5 V. When enabled, each switch will
supply a 500 mA minimum current to its load. In the unlikely event that a switch is enabled and the output
voltage of that switch is pulled above the input voltage, the bi-directional nature of the switch results in current to
flow from the output to the input. When a switch is disabled, current flow through the switch is prevented in both
directions.
CHARGE PUMP AND DRIVER
The gate voltages of the high-side NFET power switches are supplied by an internal charge-pump and driver
circuit combination. The charge pump is a low-current switched-capacitor circuit that efficiently generates
voltages above the LM3543 input supply. The charge pump output is used to supply a transconductance
amplifier driver circuit that controls the gate voltages of the power switches. Rise and fall times on the gates are
typically kept between 2 ms and 4 ms to limit large current surges and associated electromagnetic interference
(EMI).
ENABLE (ENx or ENx)
The LM3543 comes in two versions: an active-high enable version, LM3543-H, and an active-low enable version,
LM3543-L. In the LM3543-H, the ENx pins are active-high logic inputs that, when asserted, turn on the
associated power supply switch(es). Power supply switches are controlled by the ENx active-low logic inputs in
the LM3543-L. With all three ports disabled on either version of the LM3543, less than 5 µA of supply current is
consumed. Both types of enable inputs, active-high and active-low, are TTL and CMOS logic compatible.
INPUT AND OUTPUT
The power supply to the control circuitry and the drains of the power-switch MOSFETs are connected to the two
input pins, IN1 and IN2. These two pins are connected externally in most standard applications. The two ground
nodes GND1 and GND2 must be connected externally in all applications.
Pins OUT1, OUT2, and OUT3 are connections to the source nodes of the power-switch MOSFETs. In a typical
application circuit, current flows through the switches from IN1 and IN2 to OUTx toward the load.
UNDERVOLTAGE LOCKOUT (UVLO)
Undervoltage Lockout (UVLO) prevents the MOSFET switches from turning on until the input voltage exceeds a
typical value of 1.8V.
If the input voltage drops below the UVLO threshold, the MOSFET switches are opened and fault flags are
activated. UVLO flags function only when one or more of the ports is enabled. Due to the paired nature of the
design, both FLAG1 and FLAG2 will assert if either port1 or port2 is enabled in a UVLO condition.
CURRENT LIMIT AND FOLDBACK
The current limit circuit is designed to protect the system supply, the LM3543 switches, and the load from
potential damage resulting from excessive currents. If a direct short occurs on an output of the LM3543, the input
capacitor(s) rapidly discharge through the part, activating current limit circuitry. The threshold for activating
current limiting is 2.0A (typ.). Protection is achieved by momentarily opening the MOSFET switch and then
gradually turning it on. Turn-on is halted when the current through the switch reaches the current-limit level of
1.0A (typ.) The current is held at this level until either the excessive load/short is removed or the part overheats
and thermal shutdown occurs (see THERMAL SHUTDOWN section, below). The fault flag of a switch is asserted
whenever the switch is current limiting.
If a port on the LM3543 is enabled into a short condition, the output current of that port will rise to the current-
limit level and hold there.
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: LM3543
OBSOLETE
LM3543
SNVS065E –AUGUST 2000–REVISED MARCH 2013
www.ti.com
When a port is in a current-limit condition, the LM3543 senses the output voltage on that port and, if it is less
than 1.0V (typ.), will reduce the output current through that port. This operation is shown in Figure 21, below. The
current reduction, or foldback, reduces power dissipation through the overloaded MOSFET switch. An additional
advantage of the foldback feature is the reduction of power required from the source supply when one or more
output ports are shorted.
Figure 21. Short-Circuit Output Current (with Foldback) vs. Output Voltage
THERMAL SHUTDOWN
The LM3543 is internally protected against excessive power dissipation by a two-stage thermal protection circuit.
If the device temperature rises to approximately 145°C, the thermal shutdown circuitry turns off any switch that is
current limited. Non-overloaded switches continue to function normally. If the die temperature rises above 160°C,
all switches are turned off and all three fault flag outputs are activated. Hysteresis ensures that a switch turned
off by thermal shutdown will not be turned on again until the die temperature is reduced to 135°C. Shorted
switches will continue to cycle off and on, due to the rising and falling die temperature, until the short is removed.
The thermal shutdown function is shown graphically in Figure 22 and Figure 23.
Figure 22. Thermal Shutdown Characteristics when only the First-Stage Thermal-Shutdown Mode is
Needed
10
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3543
OBSOLETE
LM3543
www.ti.com
SNVS065E –AUGUST 2000–REVISED MARCH 2013
Figure 23. Thermal Shutdown Characteristics when Both First-Stage and Second-Stage Thermal-
Shutdown Modes are Needed
In Figure 22, port 1 is enabled into a short. When this occurs, the MOSFET switch of port 1 repeatedly opens
and closes as the device temperature rises and falls between 145°C and 135°C. In this example, the device
temperature never rises above 160°C. The second stage thermal shutdown is not used and port 2 remains
operational.
When port 1 is enabled into a short in the example illustrated in Figure 23, the device temperature immediately
rises above 160°C. A higher ambient temperature or a larger number of shorted outputs can cause the junction
temperature to increase, resulting in the difference in behavior between the current example and the previous
one. When the junction temperature reaches 160°C, all three ports are disabled (port 3 is not shown in the figure)
and all three fault-flag signals are asserted. Just prior to time index 2.5 ms, the device temperature falls below
135°C, all three ports activate, and all three fault flags are removed. The short condition remains on port 1,
however. For the remainder of the example, the device temperature cycles between 135°C and 145°C, causing
port 1 to repeatedly turn on and off but allowing the un-shorted ports to function normally.
SOFT START
When a power switch is enabled, high levels of current will flow instantaneously through the LM3543 to charge
the large capacitance at the output of the port. This is likely to exceed the over-current threshold of the device, at
which point the LM3543 will enter its current-limit mode. The amount of current used to charge the output
capacitor is then set by the current-limit circuitry. The device will exit the current-limit mode when the current
needed to continue to charge the output capacitor is less than the LM3543 current-limit level.
FAULT FLAG
The fault flags are open-drain outputs, each capable of sinking up to a 10 mA load current to typically 100 mV
above ground.
A parasitic diode exists between the flag pins and VIN pins. Pulling the flag pins to voltages higher than VIN will
forward bias this diode and will cause an increase in supply current. This diode will also clamp the voltage on the
flag pins to a diode drop above VIN.
The fault flag is active (pulled low) when any of the following conditions are present: under-voltage, current-limit,
or thermal-shutdown.
The LM3543 has an internal delay in reporting fault conditions that is typically 7 ms in length. In start-up, the
delay gives the device time to charge the output capacitor(s) and exit the current-limit mode before a flag signal
is set. This delay also prevents flag signal glitches from occurring when brief changes in operating conditions
momentarily place the LM3543 into one of its three error conditions. If an error condition still exists after the delay
interval has elapsed, the appropriate fault flag(s) will be asserted (pulled low) until the error condition is removed.
In most applications, the 7 ms internal flag delay eliminates the need to extend the delay with an external RC
delay network.
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: LM3543
OBSOLETE
LM3543
SNVS065E –AUGUST 2000–REVISED MARCH 2013
Application Information
OUTPUT FILTERING
www.ti.com
The schematic in Figure 3 showed a typical application circuit for the LM3543. The USB specification requires
120 µF at the output of each hub. A three-port hub with 33 µF tantalum capacitors at each port output meets the
specification. These capacitors provide short-term transient current to drive downstream devices when hot-plug
events occur. Capacitors with low equivalent-series-resistance should be used to lower the inrush current flow
through the LM3543 during a hot-plug event.
The rapid change in currents seen during a hot plug event can generate electromagnetic interference (EMI). To
reduce this effect, ferrite beads in series between the outputs of the LM3543 and the downstream USB port are
recommended. Beads should also be placed between the ground node of the LM3543 and the ground nodes of
connected downstream ports. In order to keep voltage drop across the beads to a minimum, wire with small DC
resistance should be used through the ferrite beads. A 0.01 µF - 0.1 µF ceramic capacitor is recommended on
each downstream port directly between the Vbus and ground pins to further reduce EMI effects.
POWER SUPPLY FILTERING
A sizable capacitor should be connected to the input of the LM3543 to ensure the voltage drop on this node is
less than 330 mV during a heavy-load hot-plug event. A 33 µF, 16V tantalum capacitor is recommended. The
input supply should be further bypassed with a 0.01 µF - 0.1 µF ceramic capacitor, placed close to the device.
The ceramic capacitor reduces ringing on the supply that can occur when a short is present at the output of a
port.
EXTENDING THE FAULT FLAG DELAY
While the 7 ms (typical) internal delay in reporting flag conditions is adequate for most applications, the delay can
be extended by connecting external RC filters to the FLAG pins, as shown in Figure 24.
Figure 24. Typical Circuit for Lengthening the Internal Flag Delay
POWER DISSIPATION AND JUNCTION TEMPERATURE
A few simple calculations will allow a designer to calculate the approximate operating temperature of the LM3543
for a given application. The large currents possible through the low resistance power MOSFET combined with
the high thermal resistance of the SOIC package, in relation to power packages, make this estimate an important
design step.
Begin the estimate by determining RON at the expected operating temperature using the graphs in the Typical
Performance Characteristics section of this datasheet. Next, calculate the power dissipation through the switch
with Equation 1.
2
PD = RON * IDS
(1)
Note: Equation for power dissipation neglects portion that comes from LM3543 quiescent current because this
value will almost always be insignificant.
Using this figure, determine the junction temperature with Equation 2.
TJ = PD * θJA + TA.
where
•
θJA = SOIC Thermal Resistance: 130°C/W and TA = Ambient Temperature (°C).
(2)
12
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3543
OBSOLETE
LM3543
www.ti.com
SNVS065E –AUGUST 2000–REVISED MARCH 2013
Compare the calculated temperature with the expected temperature used to estimate RON. If they do not
reasonably match, re-estimate RON using a more appropriate operating temperature and repeat the calculations.
Reiterate as necessary.
PCB LAYOUT CONSIDERATIONS
In order to meet the USB requirements for voltage drop, droop and EMI, each component used in this circuit
must be evaluated for its contribution to the circuit performance. These principles are illustrated in Figure 25. The
following PCB layout rules and guidelines are recommended
1. Place the switch as close to the USB connector as possible. Keep all Vbus traces as short as possible and
use at least 50-mil, 1 ounce copper for all Vbus traces. Solder plating the traces will reduce the trace
resistance.
2. Avoid vias as much as possible. If vias are used, use multiple vias in parallel and/or make them as large as
possible.
3. Place the output capacitor and ferrite beads as close to the USB connector as possible.
4. If ferrite beads are used, use wires with minimum resistance and large solder pads to minimize connection
resistance.
Figure 25. Self-Powered Hub Connections and Per-Port Voltage Drop
Typical Applications
ROOT AND SELF-POWERED USB HUBS
The LM3543 has been designed primarily for use in root and self-powered USB hubs. In this application, the
switches of the LM3543 are used to connect the power source of the hub to the power bus used by downstream
devices and to protect the hub from dangerously excessive loads and shorts to ground. A high-power bus-
powered function, low-power bus-powered function, or a bus-powered hub can be driven through a single port of
the LM3543. A schematic of a circuit that uses the LM3543 for power-supply switching in a typical root or self-
powered hub was shown earlier in this datasheet in Figure 3.
Voltage drop requirements of USB power supplies require the power outputs of the root and self-powered hubs
to be no less than 4.75V. For this reason, it is recommended that a 5V power supply with a ±3% output voltage
tolerance is used in this application. Combining a 3% supply with a low-resistance PCB design and the low on-
resistance of the LM3543 power switches will ensure that the hub power outputs meet the USB voltage drop
specification even with a 500mA load, the maximum allowed in the USB standard.
BUS-POWERED USB HUBS
The LM3543 is capable of performing the power supply switching functions required in Bus-Powered hubs. Use
here is very similar to the configuration used in root and self-powered hubs. With bus-powered hubs, however,
there is no internal power supply to drive the input pins of the LM3543. Instead, the input pins should be
connected to the power bus supplied by the upstream hub.
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: LM3543
OBSOLETE
LM3543
SNVS065E –AUGUST 2000–REVISED MARCH 2013
www.ti.com
USB BUS-POWERED FUNCTIONS AND GENERAL IN-RUSH CURRENT LIMITING APPLICATIONS
The LM3543 can be placed at the power-supply input of USB bus-powered functions, or other similar devices, to
protect them from high in-rush currents. If the current being delivered to the device were to exceed the 2.0A
over-current threshold (typ.) of the LM3543, switches in violation would open to protect the device from damage.
In addition to in-rush current limiting, the LM3543 can be used in high-power bus-powered functions to keep
current levels of the function in compliance during power-up. The USB specification requires the staged switching
of power when connecting high-power functions to the bus. When a high-power function is initially connected to
the bus, it must not draw more than one unit supply (100mA). After a connection is detected and enumerated,
and if the upstream device is capable of supplying the required power, the high-power function may draw up to
five unit loads (500mA). With the proper control signals, the LM3543 can be used to achieve this staged power
connection. When the function is connected to the bus, one or more of the LM3543 switches can be closed to
connect bus power only to circuitry needed during the connection and enumeration process. If the function is to
be powered fully, remaining switches on the LM3543 can be closed to connect all blocks of the function to the
power bus. Figure 26 illustrates how the LM3543 can be connected for use in bus powered functions.
LM3543-H
Internal Function
(with start-up
circuitry)
15
14
11
2
6
OUT1
OUT2
OUT3
IN1
IN2
V
BUS
10 mF
0.1 mF
10 mF
10 mF
10 mF
0.1 mF
0.1 mF
0.1 mF
D+
D-
GND
3.3V Power
Supply
Internal
Function
Internal
Function
16
13
12
FLAG1
FLAG2
FLAG3
USB
Control
8, 9, 10
3
4
7
NC
EN1
EN2
EN3
1
5
GND1
GND2
Figure 26. Using the LM3543 in USB Bus-Powered Functions
14
Submit Documentation Feedback
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM3543
OBSOLETE
LM3543
www.ti.com
SNVS065E –AUGUST 2000–REVISED MARCH 2013
REVISION HISTORY
Changes from Revision D (March 2013) to Revision E
Page
•
Changed layout of National Data Sheet to TI format .......................................................................................................... 14
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: LM3543
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
相关型号：
©2020 ICPDF网 联系我们和版权申明