LM5100AMR [TI]
High-Voltage, High-Side and Low-Side Gate Drivers;型号: | LM5100AMR |
厂家: | TEXAS INSTRUMENTS |
描述: | High-Voltage, High-Side and Low-Side Gate Drivers 栅 驱动 光电二极管 接口集成电路 驱动器 |
文件: | 总20页 (文件大小:593K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LM5100A,LM5100B,LM5100C,LM5101A,LM5101B,
LM5101C
LM5100A/B/C LM5101A/B/C 3A, 2A and 1A High Voltage High-Side and Low-Side
Gate Drivers
Literature Number: SNOSAW2M
August 20, 2011
LM5100A/B/C
LM5101A/B/C
3A, 2A and 1A High Voltage High-Side and Low-Side Gate
Drivers
Bootstrap supply voltage up to 118V DC
■
■
■
■
■
■
■
General Description
Fast propagation times (25 ns typical)
The LM5100A/B/C and LM5101A/B/C High Voltage Gate
Drives 1000 pF load with 8 ns rise and fall times
Drivers are designed to drive both the high-side and the low-
side N-Channel MOSFETs in a synchronous buck or a half-
bridge configuration. The floating high-side driver is capable
of operating with supply voltages up to 100V. The “A” versions
provide a full 3A of gate drive while the “B” and “C” versions
provide 2A and 1A respectively. The outputs are indepen-
dently controlled with CMOS input thresholds (LM5100A/B/C)
or TTL input thresholds (LM5101A/B/C). An integrated high
voltage diode is provided to charge the high-side gate drive
bootstrap capacitor. A robust level shifter operates at high
speed while consuming low power and providing clean level
transitions from the control logic to the high-side gate driver.
Under-voltage lockout is provided on both the low-side and
the high-side power rails. These devices are available in the
standard SOIC-8 pin, PSOP-8 pin and the LLP-10 pin pack-
ages. The LM5100C and LM5101C are also available in
eMSOP-8 package. The LM5101A is also available in LLP-8
pin package.
Excellent propagation delay matching (3 ns typical)
Supply rail under-voltage lockout
Low power consumption
Pin compatible with HIP2100/HIP2101
Typical Applications
Current Fed push-pull converters
■
■
■
■
Half and Full Bridge power converters
Synchronous buck converters
Two switch forward power converters
Forward with Active Clamp converters
■
Package
SOIC-8
■
■
■
■
PSOP-8
LLP-8 (4 mm x 4 mm)
Features
LLP-10 (4 mm x 4 mm)
Drives both a high-side and low-side N-Channel
MOSFETs
■
eMSOP-8
■
Independent high and low driver logic inputs
■
Simplified Block Diagram
20203103
FIGURE 1.
© 2011 National Semiconductor Corporation
202031
www.national.com
Input/Output Options
Part Number
LM5100A
LM5101A
LM5100B
LM5101B
LM5100C
LM5101C
Input Thresholds
CMOS
TTL
Peak Output Current
3A
3A
2A
2A
1A
1A
CMOS
TTL
CMOS
TTL
Connection Diagrams
20203101
20203137
20203102
20203135
20203136
www.national.com
2
Ordering Information
Ordering Number
LM5100A/LM5101AM
LM5100A/LM5101AMX
LM5100A/LM5101AMR
LM5100A/LM5101AMRX
LM5100A /LM5101ASD
LM5100A/LM5101ASDX
LM5100B/LM5101BMA
LM5100B/LM5101BMAX
LM5100B/LM5101BSD
LM5100B/LM5101BSDX
LM5100C/LM5101CMA
LM5100C/LM5101CMAX
LM5100C /LM5101CSD
LM5100C/LM5101CSDX
LM5100C/LM5101CMYE
LM5100C/LM5101CMY
LM5100C/LM5101CMYX
LM5101ASD-1
Package Type
NSC Package Drawing
M08A
Supplied As
SOIC 8
SOIC 8
PSOP 8
PSOP 8
LLP 10
LLP 10
SOIC 8
SOIC 8
LLP 10
LLP 10
SOIC 8
SOIC 8
LLP 10
LLP 10
eMSOP-8
eMSOP-8
eMSOP-8
LLP 8
95 units shipped in anti static rails
2500 shipped in Tape & Reel
95 units shipped in anti static rails
2500 shipped in Tape & Reel
1000 shipped in Tape & Reel
4500 shipped in Tape & Reel
95 units shipped in anti static rails
2500 shipped in Tape & Reel
1000 shipped in Tape & Reel
4500 shipped in Tape & Reel
95 units shipped in anti static rails
2500 shipped in Tape & Reel
1000 shipped in Tape & Reel
4500 shipped in Tape & Reel
250 shipped in Tape & Reel
1000 shipped in Tape & Reel
3500 shipped in Tape & Reel
1000 shipped in Tape & Reel
4500 shipped in Tape & Reel
M08A
MRA08A
MRA08A
SDC10A
SDC10A
M08A
M08A
SDC10A
SDC10A
M08A
M08A
SDC10A
SDC10A
MUY08A
MUY08A
MUY08A
SDC08A
SDC08A
LM5101ASDX-1
LLP 8
3
www.national.com
Pin Descriptions
Pin #
Name
Description
Application Information
SOIC-8 PSOP-8
LLP-8
LLP-10
eMSOP-8
1
1
1
1
1
VDD
Positive gate drive
supply
Locally decouple to VSS using low
ESR/ESL capacitor located as close
to the IC as possible.
2
2
2
2
2
HB
High-side gate driver Connect the positive terminal of the
bootstrap rail
bootstrap capacitor to HB and the
negative terminal to HS. The
bootstrap capacitor should be placed
as close to the IC as possible.
3
4
5
3
4
5
3
4
5
3
4
7
3
4
5
HO
HS
HI
High-side gate driver Connect to the gate of high-side
output
MOSFET with a short, low
inductance path.
High-side MOSFET
source connection
Connect to the bootstrap capacitor
negative terminal and the source of
the high-side MOSFET.
High-side driver
control input
The LM5100A/B/C inputs have
CMOS type thresholds. The
LM5101A/B/C inputs have TTL type
thresholds. Unused inputs should be
tied to ground and not left open.
6
6
6
8
6
LI
Low-side driver
control input
The LM5100A/B/C inputs have
CMOS type thresholds. The
LM5101A/B/C inputs have TTL type
thresholds. Unused inputs should be
tied to ground and not left open.
7
8
7
8
7
8
9
7
8
VSS
LO
Ground return
All signals are referenced to this
ground.
10
Low-side gate driver Connect to the gate of the low-side
output
MOSFET with a short, low
inductance path.
EP
EP
EP
EP
EP (LLP and PSOP and eMSOP
packages)
Solder to the ground plane under the
IC to aid in heat dissipation.
Note: For LLP-8, LLP-10 and eMSOP-8 package, it is recommended that the exposed pad on the bottom of the package is soldered to ground plane
on the PC board, and that ground plane should extend out from beneath the IC to help dissipate heat. For LLP-10 package, pins 5 and 6 have no
connection.
www.national.com
4
Junction Temperature
Storage Temperature Range
ESD Rating HBM (Note 2)
+150°C
−55°C to +150°C
2 kV
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Recommended Operating
VDD to VSS
HB to HS
−0.3V to +18V
−0.3V to +18V
Conditions
VDD
HS
+9V to +14V
−1V to 100V
VHS +8V to VHS +14V
< 50 V/ns
LI or HI Input
LO Output
−0.3V to VDD +0.3V
−0.3V to VDD +0.3V
VHS −0.3V to VHB +0.3V
−5V to +100V
HB
HO Output
HS Slew Rate
Junction Temperature
HS to VSS (Note 6)
HB to VSS
−40°C to +125°C
118V
Electrical Characteristics
Limits in standard type are for TJ = 25°C only; limits in boldface type apply over the junction temperature (TJ) range of -40°C to
+125°C. Minimum and Maximum limits are guaranteed through test, design, or statistical correlation. Typical values represent the
most likely parametric norm at TJ = 25°C, and are provided for reference purposes only. Unless otherwise specified, VDD = VHB
=
12V, VSS = VHS = 0V, No Load on LO or HO (Note 4).
Symbol
Parameter
Conditions
Min
Typ
Max
Units
SUPPLY CURRENTS
IDD
VDD Quiescent Current, LM5100A/B/C
VDD Quiescent Current, LM5101A/B/C
VDD Operating Current
LI = HI = 0V
0.1
0.25
2.0
0.2
0.4
3
mA
LI = HI = 0V
f = 500 kHz
LI = HI = 0V
f = 500 kHz
HS = HB = 100V
f = 500 kHz
IDDO
IHB
mA
mA
mA
µA
Total HB Quiescent Current
0.06
1.6
0.2
3
IHBO
IHBS
IHBSO
Total HB Operating Current
HB to VSS Current, Quiescent
HB to VSS Current, Operating
0.1
10
0.4
mA
INPUT PINS
VIL
Input Voltage Threshold LM5100A/B/C
Rising Edge
Rising Edge
4.5
1.3
5.4
1.8
500
50
6.3
2.3
V
VIL
Input Voltage Threshold LM5101A/B/C
Input Voltage Hysteresis LM5100A/B/C
Input Voltage Hysteresis LM5101A/B/C
Input Pulldown Resistance
V
VIHYS
VIHYS
RI
mV
mV
kΩ
100
6.0
5.7
200
400
7.4
7.1
UNDER VOLTAGE PROTECTION
VDDR
VDDH
VHBR
VHBH
VDD Rising Threshold
VDD Threshold Hysteresis
HB Rising Threshold
6.9
0.5
6.6
0.4
V
V
V
V
HB Threshold Hysteresis
BOOT STRAP DIODE
VDL
VDH
RD
Low-Current Forward Voltage
High-Current Forward Voltage
IVDD-HB = 100 µA
IVDD-HB = 100 mA
0.52
0.8
0.85
1
V
V
Dynamic Resistance LM5100A/B/C, LM5101A/B/ IVDD-HB = 100 mA
C
1.0
1.65
Ω
LO & HO GATE DRIVER
VOL
VOH
IOHL
Low-Level Output Voltage LM5100A/LM5101A IHO = ILO = 100 mA
0.12
0.16
0.28
0.24
0.28
0.60
3
0.25
0.4
Low-Level Output Voltage LM5100B/LM5101B
V
V
A
Low-Level Output Voltage LM5100C/LM5101C
0.65
0.45
0.60
1.10
High-Level Output Voltage LM5100A/LM5101A IHO = ILO = 100 mA
VOH = VDD– LO or
VOH = HB - HO
High-Level Output Voltage LM5100B/LM5101B
High-Level Output Voltage LM5100C/LM5101C
Peak Pullup Current LM5100A/LM5101A
Peak Pullup Current LM5100B/LM5101B
Peak Pullup Current LM5100C/LM5101C
HO, LO = 0V
2
1
5
www.national.com
Symbol
Parameter
Conditions
HO, LO = 12V
Min
Typ
3
Max
Units
IOLL
Peak Pulldown Current LM5100A/LM5101A
Peak Pulldown Current LM5100B/LM5101B
Peak Pulldown Current LM5100C/LM5101C
2
A
1
THERMAL RESISTANCE
Junction to Ambient
SOIC-8
170
40
40
40
80
θJA
LLP-8(Note 3)
LLP-10 (Note 3)
PSOP-8
°C/W
eMSOP-8 (Note 3)
Switching Characteristics
Limits in standard type are for TJ = 25°C only; limits in boldface type apply over the junction temperature (TJ) range of -40°C to
+125°C. Minimum and Maximum limits are guaranteed through test, design, or statistical correlation. Typical values represent the
most likely parametric norm at TJ = 25°C, and are provided for reference purposes only. Unless otherwise specified, VDD = VHB
=
12V, VSS = VHS = 0V, No Load on LO or HO (Note 4).
Symbol
tLPHL
Parameter
Conditions
Min
Typ
Max
45
Units
LO Turn-Off Propagation Delay
LM5100A/B/C
LI Falling to LO Falling
20
ns
ns
ns
LO Turn-Off Propagation Delay
LM5101A/B/C
22
20
26
20
22
20
26
1
56
45
56
45
56
45
56
10
10
10
10
tLPLH
tHPHL
tHPLH
tMON
tMOFF
LO Turn-On Propagation Delay
LM5100A/B/C
LI Rising to LO Rising
HI Falling to HO Falling
HI Rising to HO Rising
LO Turn-On Propagation Delay
LM5101A/B/C
HO Turn-Off Propagation Delay
LM5100A/B/C
HO Turn-Off Propagation Delay
LM5101A/B/C
LO Turn-On Propagation Delay
LM5100A/B/C
ns
ns
LO Turn-On Propagation Delay
LM5101A/B/C
Delay Matching: LO on & HO off
LM5100A/B/C
Delay Matching: LO on & HO off
LM5101A/B/C
4
Delay Matching: LO off & HO on
LM5100A/B/C
1
ns
ns
ns
Delay Matching: LO on & HO off
LM5101A/B/C
4
8
tRC, tFC
tR
Either Output Rise/Fall Time
CL = 1000 pF
Output Rise Time (3V to 9V) LM5100A/ CL = 0.1 µF
LM5101A
430
Output Rise Time (3V to 9V) LM5100B/
LM5101B
570
990
260
430
715
Output Rise Time (3V to 9V) LM5100C/
LM5101C
tF
Output Fall Time (3V to 9V) LM5100A/
LM5101A
CL = 0.1 µF
Output Fall Time (3V to 9V) LM5100B/
LM5101B
ns
Output Fall Time (3V to 9V) LM5100C/
LM5101C
www.national.com
6
Symbol
tPW
Parameter
Conditions
Min
Typ
Max
Units
Minimum Input Pulse Width that Changes
the Output
50
ns
tBS
Bootstrap Diode Reverse Recovery Time IF = 100 mA,
IR = 100 mA
37
ns
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the component may occur. Operating Ratings are conditions under which operation
of the device is guaranteed. Operating Ratings do not imply guaranteed performance limits. For guaranteed performance limits and associated test conditions,
see the Electrical Characteristics tables.
Note 2: The Human Body Model (HBM) is a 100 pF capacitor discharged through a 1.5kΩ resistor into each pin. 2 kV for all pins except Pin 2, Pin 3 and Pin 4
which are rated at 1000V for HBM. Machine Model (MM) ratings are : 100V(MM) for Options B and C; 50V(MM) for Option A.
Note 3: 4 layer board with Cu finished thickness 1.5/1/1/1.5 oz. Maximum die size used. 5x body length of Cu trace on PCB top. 50 x 50mm ground and power
planes embedded in PCB. See Application Note AN-1187.
Note 4: Min and Max limits are 100% production tested at 25°C. Limits over the operating temperature range are guaranteed through correlation using Statistical
Quality Control (SQC) methods. Limits are used to calculate National’s Average Outgoing Quality Level (AOQL).
Note 5: The θJA is not a given constant for the package and depends on the printed circuit board design and the operating environment.
Note 6: In the application the HS node is clamped by the body diode of the external lower N-MOSFET, therefore the HS node will generally not exceed -1V.
However, in some applications, board resistance and inductance may result in the HS node exceeding this stated voltage transiently. If negative transients occur,
the HS voltage must never be more negative than VDD-15V. For example if VDD = 10V, the negative transients at HS must not exceed -5V.
Typical Performance Characteristics
Peak Sourcing Current vs VDD
Peak Sinking Current vs VDD
20203128
20203127
Sink Current vs Output Voltage
Source Current vs Output Voltage
20203129
20203130
7
www.national.com
LM5100A/B/C IDD vs Frequency
LM5101A/B/C IDD vs Frequency
20203110
20203109
Operating Current vs Temperature
IHB vs Frequency
20203111
20203114
Quiescent Current vs Supply Voltage
Quiescent Current vs Temperature
20203119
20203118
www.national.com
8
Undervoltage Rising Thresholds vs Temperature
Undervoltage Threshold Hysteresis vs Temperature
20203122
20203117
Bootstrap Diode Forward Voltage
LM5100A/B/C Input Threshold vs Temperature
20203123
20203115
LM5101A/B/C Input Threshold vs Temperature
LM5100A/B/C Input Threshold vs VDD
20203125
20203124
9
www.national.com
LM5101A/B/C Input Threshold vs VDD
LM5100A/B/C Propagation Delay vs Temperature
20203126
20203112
LM5101A/B/C Propagation Delay vs Temperature
LO & HO Gate Drive - High Level Output Voltage vs
Temperature
20203113
20203120
LO & HO Gate Drive - Low Level Output Voltage vs
Temperature
LO & HO Gate Drive - Output High Voltage vs VDD
20203131
20203121
www.national.com
10
LO & HO Gate Drive - Output Low Voltage vs VDD
20203132
Timing Diagram
20203104
FIGURE 2.
11
www.national.com
discharge the MOSFET gate into a minimal physical
area. This will decrease the loop inductance and
minimize noise issues on the gate terminal of the
MOSFET. The MOSFETs should be placed as close as
possible to the gate driver.
Layout Considerations
The optimum performance of high and low-side gate drivers
cannot be achieved without taking due considerations during
circuit board layout. Following points are emphasized.
b) The second high current path includes the bootstrap
capacitor, the bootstrap diode, the local ground
referenced bypass capacitor and low-side MOSFET
body diode. The bootstrap capacitor is recharged on a
cycle-by-cycle basis through the bootstrap diode from
the ground referenced VDD bypass capacitor. The
recharging occurs in a short time interval and involves
high peak current. Minimizing this loop length and area
on the circuit board is important to ensure reliable
operation.
1. Low ESR / ESL capacitors must be connected close to
the IC, between VDD and VSS pins and between the HB
and HS pins to support the high peak currents being
drawn from VDD during turn-on of the external MOSFET.
2. To prevent large voltage transients at the drain of the top
MOSFET, a low ESR electrolytic capacitor must be
connected between MOSFET drain and ground (VSS).
3. In order to avoid large negative transients on the switch
node (HS pin), the parasitic inductances in the source of
top MOSFET and in the drain of the bottom MOSFET
(synchronous rectifier) must be minimized.
A recommended layout pattern for the driver is shown in the
following figure. If possible a single layer placement is pre-
ferred.
4. Grounding Considerations:
a) The first priority in designing grounding connections
is to confine the high peak currents that charge and
20203138
www.national.com
12
Diode Power Dissipation VIN = 50V
Power Dissipation Considerations
The total IC power dissipation is the sum of the gate driver
losses and the bootstrap diode losses. The gate driver losses
are related to the switching frequency (f), output load capac-
itance on LO and HO (CL), and supply voltage (VDD) and can
be roughly calculated as:
2
PDGATES = 2 • f • CL • VDD
There are some additional losses in the gate drivers due to
the internal CMOS stages used to buffer the LO and HO out-
puts. The following plot shows the measured gate driver
power dissipation versus frequency and load capacitance. At
higher frequencies and load capacitance values, the power
dissipation is dominated by the power losses driving the out-
put loads and agrees well with the above equation. This plot
can be used to approximate the power losses due to the gate
drivers.
20203106
Gate Driver Power Dissipation (LO + HO)
VDD = 12V, Neglecting Diode Losses
20203105
The bootstrap diode power loss is the sum of the forward bias
power loss that occurs while charging the bootstrap capacitor
and the reverse bias power loss that occurs during reverse
recovery. Since each of these events happens once per cycle,
the diode power loss is proportional to frequency. Larger ca-
pacitive loads require more energy to recharge the bootstrap
capacitor resulting in more losses. Higher input voltages
(VIN) to the half bridge result in higher reverse recovery loss-
es. The following plot was generated based on calculations
and lab measurements of the diode recovery time and current
under several operating conditions. This can be useful for ap-
proximating the diode power dissipation.
The total IC power dissipation can be estimated from the pre-
vious plots by summing the gate drive losses with the boot-
strap diode losses for the intended application.
13
www.national.com
Physical Dimensions inches (millimeters) unless otherwise noted
Controlling dimension is inch. Values in [ꢀ] are millimeters.
Notes: Unless otherwise specified.
Standard lead finish to be 200 microinches/5.08 micrometers minimum lead/tin (solder) on copper.
1.
Dimension does not include mold flash.
2.
Reference JEDEC registration MS-012, Variation AA, dated May 1990.
3.
SOIC-8 Outline Drawing
NS Package Number M08A
PSOP-8 Outline Drawing
NS Package Number MRA08A
www.national.com
14
LLP-8 Outline Drawing
NS Package Number SDC08A
Notes: Unless otherwise specified.
For solder thickness and composition, see “Solder Information” in the packaging section of the National Semiconductor web page (www.national.com).
Maximum allowable metal burr on lead tips at the package edges is 76 microns.
1.
2.
3.
No JEDEC registration as of May 2003.
LLP-10 Outline Drawing
NS Package Number SDC10A
15
www.national.com
eMSOP-8 Outline Drawing
NS Package Number MUY08A
www.national.com
16
Notes
17
www.national.com
Notes
For more National Semiconductor product information and proven design tools, visit the following Web sites at:
www.national.com
Products
www.national.com/amplifiers
Design Support
www.national.com/webench
Amplifiers
WEBENCH® Tools
App Notes
Audio
www.national.com/audio
www.national.com/timing
www.national.com/adc
www.national.com/interface
www.national.com/lvds
www.national.com/power
www.national.com/appnotes
www.national.com/refdesigns
www.national.com/samples
www.national.com/evalboards
www.national.com/packaging
www.national.com/quality/green
www.national.com/contacts
www.national.com/quality
www.national.com/feedback
www.national.com/easy
Clock and Timing
Data Converters
Interface
Reference Designs
Samples
Eval Boards
LVDS
Packaging
Power Management
Green Compliance
Distributors
Switching Regulators www.national.com/switchers
LDOs
www.national.com/ldo
www.national.com/led
www.national.com/vref
www.national.com/powerwise
Quality and Reliability
Feedback/Support
Design Made Easy
Applications & Markets
Mil/Aero
LED Lighting
Voltage References
PowerWise® Solutions
www.national.com/solutions
www.national.com/milaero
www.national.com/solarmagic
www.national.com/training
Serial Digital Interface (SDI) www.national.com/sdi
Temperature Sensors
PLL/VCO
www.national.com/tempsensors SolarMagic™
www.national.com/wireless
PowerWise® Design
University
THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION
(“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY
OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO
SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS,
IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS
DOCUMENT.
TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT
NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL
PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR
APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND
APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE
NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS.
EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO
LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE
AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR
PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY
RIGHT.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR
SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and
whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected
to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform
can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.
National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other
brand or product names may be trademarks or registered trademarks of their respective holders.
Copyright© 2011 National Semiconductor Corporation
For the most current product information visit us at www.national.com
National Semiconductor
Americas Technical
Support Center
National Semiconductor Europe
Technical Support Center
Email: europe.support@nsc.com
National Semiconductor Asia
Pacific Technical Support Center
Email: ap.support@nsc.com
National Semiconductor Japan
Technical Support Center
Email: jpn.feedback@nsc.com
Email: support@nsc.com
Tel: 1-800-272-9959
www.national.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Audio
Applications
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
www.ti.com/industrial
www.ti.com/medical
www.ti.com/security
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
Medical
Security
Logic
Space, Avionics and Defense www.ti.com/space-avionics-defense
Transportation and Automotive www.ti.com/automotive
Power Mgmt
Microcontrollers
RFID
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
Video and Imaging
www.ti.com/video
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明