LM84BIMQA/NOPB [TI]
具有 SMBus 和 I2C 接口的 ±1°C 远程和本地温度传感器 | DBQ | 16 | 0 to 125;
| 型号： | LM84BIMQA/NOPB |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | 具有 SMBus 和 I2C 接口的 ±1°C 远程和本地温度传感器 | DBQ | 16 | 0 to 125 温度传感 输出元件 传感器 换能器 温度传感器 |
| 文件： | 总18页 (文件大小：207K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
LM84
LM84 Diode Input Digital Temperature Sensor with Two-Wire Interface
Literature Number: SNIS108B
July 2000
LM84
Diode Input Digital Temperature Sensor with Two-Wire
Interface
n Register readback capability
n 7 bit plus sign temperature data format
n 2 address select lines enable 9 LM84s to be connected
to a single bus
General Description
The LM84 is
a remote diode temperature sensor,
Delta-Sigma analog-to-digital converter, and digital
over-temperature detector with an SMBus interface. The
™
LM84 senses its own temperature as well as the tempera-
ture of a target IC with a diode junction, such as a Pentium®
II processor or a diode connected 2N3904. A diode junction
(semiconductor junction) is required on the target IC’s die. A
host can query the LM84 at any time to read the temperature
of this diode as well as the temperature state of the LM84
itself. A T_CRIT_A interrupt output becomes active when the
temperature is greater than a programmable comparator
limit, T_CRIT.
Key Specifications
j
j
j
j
Supply Voltage
3.0V - 3.6V
1 mA (max)
Supply Current
±
Local Temperature Accuracy
Remote Diode Temperature Accuracy
+60˚C to +100˚C
1.0˚C (typ)
±
3˚C (max)
5˚C (max)
±
0˚C to +125˚C
The host can program as well as read back the state of the
T_CRIT register. Three state logic inputs allow two pins
(ADD0, ADD1) to select up to 9 SMBus address locations for
the LM84. The sensor powers up with default thresholds of
127˚C for T_CRIT.
Applications
n System Thermal Management
n Personal Computers
n Electronic Test Equipment
n Office Electronics
Features
n Directly senses die temperature of remote ICs
n Senses temperature of remote diodes
n SMBus compatible interface, supports SMBus Timeout
n HVAC
Simplified Block Diagram
DS100961-1
# Indicates Active Low (”NOT“)
™
SMBus is a trademark of the Intel Corporation.
Pentium® II processor is a registered trademark of the Intel Corporation.
2
I
C® is a registered trademark of the Philips Corporation.
© 2001 National Semiconductor Corporation
DS100961
www.national.com
Connection Diagram
QSOP-16
DS100961-2
TOP VIEW
Ordering Information
NS
SMBus
Order
Transport
Media
Noise Filter
on SMBCLK
Package
Number
Revision
Level
1.1
Number
MQA16A
(QSOP-16)
95 Units in
Rail
20MHz
20MHz
LM84BIMQA
LM84BIMQAX
LM84CIMQA
LM84CIMQAX
MQA16A
(QSOP-16)
2500 Units on
Tape and
Reel
1.1
MQA16A
(QSOP-16)
95 Units in
Rail
1.0
1.0
Not Available
Not Available
MQA16A
(QSOP-16)
2500 Units on
Tape and
Reel
Typical Application
DS100961-3
www.national.com
2
Pin Descriptions
#
Label
Pin
Function
Typical Connection
Manufacturing test pins.
Left floating. PC board traces may be routed
through the pads for these pins. Although, the
components that drive these traces should share
the same supply as the LM84 so that the Absolute
Maximum Voltage at any Pin rating is not violated.
1, 5, 9,
13, 16
NC
Positive Supply Voltage
Input
VCC
D+
2
3
4
DC Voltage from 3.0V to 3.6V
Diode Current Source
To Diode Anode. Connected to remote discrete
diode or to the diode on the external IC whose die
temperature is being sensed.
Diode Return Current
Sink
To Diode Cathode. Must be grounded when not
used.
D−
User-Set SMBus (I2C)
Address Inputs
Ground (Low, “0”), VCC (High, “1”) or open
(“TRI-LEVEL”)
ADD0–ADD1
GND
10, 6
7, 8
11
Power Supply Ground
Ground
Critical Temperature
Alarm, open-drain output
Pull Up Resistor, Controller Interrupt Line or
System Shutdown
T_CRIT_A
SMBus (I2C) Serial
Bi-Directional Data Line,
open-drain output
From and to Controller, Pull Up Resistor
SMBData
12
SMBCLK
NC
14
15
SMBus (I2C) Clock Input
From Controller
No Connection
Left floating. PC board traces may be routed
through the pads for this pin.
3
www.national.com
Absolute Maximum Ratings (Note 1)
Soldering Information, Lead Temperature
QSOP Package (Note 3)
Vapor Phase (60 seconds)
Infrared (15 seconds)
Supply Voltage
−0.3V to 6.0V
215˚C
220˚C
Voltage at Any Pin:
NC (Pins 1,5,9), ADD0, ADD1, D+
−0.3V to
(VCC + 0.3V)
ESD Susceptibility (Note 4)
Human Body Model
2500V
250V
All other pins (except D−)
D− Input Current
−0.3V to 6.0V
Machine Model
±
1 mA
Input Current at All Other Pins (Note
2)
Operating Ratings
(Note 1) and (Note 5)
5 mA
Package Input Current (Note 2)
20 mA
SMBData, T_CRIT_A Output Sink
Current
Specified Temperature Range
LM84
TMIN to TMAX
0˚C to +125˚C
+3.0V to +3.6V
10 mA
6.0V
Output Voltage
Supply Voltage Range (VCC
)
Storage Temperature
−65˚C to +150˚C
Temperature-to-Digital Converter Characteristics
Unless otherwise noted, these specifications apply for VCC=+3.0 Vdc to +3.6 Vdc. Boldface limits apply for TA = TJ = TMIN
to TMAX; all other limits TA= TJ=+25˚C, unless otherwise noted.
Parameter
Conditions
Typical
Limits
Units
(Limit)
˚C
(Note 6)
(Note 7)
±
Local Temperature Error (Note 8)
1
±
±
Remote Temperature Error using
Pentium Diode (Note 8) and (Note
9)
+60˚C ≤TA ≤ +100˚C,
VCC = 3.3 Vdc
3
5
˚C (max)
˚C (max)
0˚C ≤ TA ≤ +125˚C,
VCC = 3.3 Vdc
Remote Temperature Error using
Diode Connected 2N3904 (Note 8)
and (Note 9)
+60˚C ≤TA ≤ +100˚C,
VCC = 3.3 Vdc
+1, −5
+3, −7
˚C (max)
˚C (max)
0˚C ≤ TA ≤ +125˚C,
VCC = 3.3 Vdc
Resolution
8
Bits
˚C
1
Temperature Conversion Time
Quiescent Current (Note 10)
D− Source Voltage
(Note 11)
SMBus (I2C Inactive)
120
0.500
0.7
145
1
ms
mA (max)
V
Diode Source Current
(D+ − D−)=+ 0.65V; high
level
160
50
16
5
µA (max)
µA (min)
µA (max)
µA (min)
Low level
T_CRIT_A Output Saturation
Voltage
IOUT = 3.0 mA
0.4
V (max)
Power-On Reset Threshold
On VCC input, falling
edge
2.2
1.2
V (max)
V (min)
Local and Remote T_CRIT Default
Temperature
(Note 12)
+127
˚C
www.national.com
4
Logic Electrical Characteristics
DIGITAL DC CHARACTERISTICS
Unless otherwise noted, these specifications apply for VCC=+3.0 to 3.6 Vdc. Boldface limits apply for TA = TJ = TMIN to
TMAX; all other limits TA= TJ=+25˚C, unless otherwise noted.
Symbol Parameter Conditions
Typical
LM84B
LM84C
Units
(Note 6)
Limits
(Note 7)
Limits
(Note 7)
(Limit)
SMBData, SMBCLK
VIN(1)
VIN(0)
IIN(1)
Logical “1” Input Voltage
Logical “0”Input Voltage
Logical “1” Input Current
Logical “0” Input Current
2.1
0.8
1.4
0.6
V (min)
V (max)
µA (max)
µA (max)
VIN = VCC
0.005
1.0
1.0
IIN(0)
VIN = 0V
−0.005
−1.0
−1.0
ADD0, ADD1
VIN(1)
VIN(0)
IIN(1)
Logical “1” Input Voltage
Logical “0”Input Voltage
Logical “1” Input Current
Logical “0” Input Current
VCC
GND
50
1.6
0.5
1.6
0.5
V (min)
V (max)
µA (max)
µA (max)
VIN = VCC
VIN = 0V
600
600
600
600
IIN(0)
50
ALL DIGITAL INPUTS
CIN
Input Capacitance
20
pF
ALL DIGITAL OUTPUTS
IOH
High Level Output Current
VOH = VCC
100
100
µA (max)
V (max)
VOL
SMBus Low Level Output
Voltage
IOL = 3 mA
IOL = 6 mA
0.4
0.6
0.4
0.6
5
www.national.com
Logic Electrical Characteristics (Continued)
SMBus DIGITAL SWITCHING CHARACTERISTICS
Unless otherwise noted, these specifications apply for VCC=+3.0 Vdc to +3.6 Vdc, CL (load capacitance) on output lines = 80
pF. Boldface limits apply for TA = TJ = TMIN to TMAX; all other limits TA = TJ = +25˚C, unless otherwise noted.
The switching characteristics of the LM84 fully meet or exceed the published specifications of the SMBus or I2C bus. The fol-
lowing parameters are the timing relationships between SMBCLK and SMBData signals related to the LM84. They are not nec-
essarily the I2C or SMBus bus specifications.
Symbol
Parameter
Conditions
Typical
Limits
Units
(Note 6)
(Note 7)
(Limit)
fSMB
tLOW
SMBus Clock Frequency
SMBus Clock Low Time
400
10
kHz (max)
kHz (min)
10% to 10%
1.3
25
µs (min)
ms (max)
t
LOWSEXT Cumulative Clock Low Extend Time
25
ms (max)
µs (min)
µs
tHIGH
tR;SMB
tF;SMB
tOF
SMBus Clock High Time
SMBus Rise Time
SMBus Fall Time
90% to 90%
10% to 90%
90% to 10%
0.6
1
0.3
µs
Output Fall Time
CL = 400 pF
IO = 3 mA
250
ns (max)
tTIMEOUT
SMBData and SMBCLK Time Low for
Reset of Serial Interface (Note 13)
25
40
ms (min)
ms (max)
t1
SMBCLK (Clock) Period
2.5
µs (min)
ns (min)
t2,
Data In Setup Time to SMBCLK High
100
tSU;DAT
t3,
tHD;DAT
Data Out Stable after SMBCLK Low
0
0.9
ns (min)
µs (max)
t4,
tHD;STA
SMBData Low Setup Time to SMBCLK
Low
100
100
0.6
1.3
ns (min)
ns (min)
µs (min)
µs (min)
t5,
tSU;STO
SMBData High Delay Time after
SMBCLK High (Stop Condition Setup)
t6,
tSU;STA
SMBus Start-Condition Setup Time
SMBus Free Time
tBUF
SMBus Communication
DS100961-4
www.national.com
6
Logic Electrical Characteristics (Continued)
SMBus TIMEOUT
DS100961-13
7
www.national.com
Logic Electrical Characteristics (Continued)
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not apply when operating
the device beyond its rated operating conditions.
<
>
V
Note 2: When the input voltage (V ) at any pin exceeds the power supplies (V
GND or V
), the current at that pin should be limited to 5 mA. The 20 mA
CC
I
I
I
maximum package input current rating limits the number of pins that can safely exceed the power supplies with an input current of 5 mA to four.
Parasitics and or ESD protection circuitry are shown in the figure below for the LM84’s pins. The nominal breakdown voltage of the zener D3 is 6.5V. Care should
be taken not to forward bias the parasitic diode, D1, present on pins: NC pins 1,5 and 9, D+, ADD1 and ADD0. Doing so by more than 50 mV may corrupt a
temperature or voltage measurement.
Pin Name
D1
D2
D3
x
D4
Pin Name
T_CRIT_A
D1
D2
x
D3
D4
NC (pins 1, 5, 9)
x
x
VCC
x
SMBData
x
x
x
x
D+
x
x
x
x
x
x
NC (pin 13)
SMBCLK
x
D−
x
x
ADD0, ADD1
x
NC (pin 16)
x
Note: An x indicates that the diode exists.
DS100961-8
FIGURE 1. ESD Protection Input Structure
Note 3: See AN-450 “Surface Mounting Methods and Their Effect on Product Reliability” or the section titled “Surface Mount” found in a current National
Semiconductor Linear Data Book for other methods of soldering surface mount devices.
Note 4: Human body model, 100 pF discharged through a 1.5 kΩ resistor. Machine model, 200 pF discharged directly into each pin.
Note 5: Thermal resistance of the QSOP-16 package is TBD ˚C/W, junction-to-ambient when attached to a printed circuit board with 2 oz. foil.
Note 6: Typicals are at T = 25˚C and represent most likely parametric norm.
A
Note 7: Limits are guaranteed to National’s AOQL (Average Outgoing Quality Level).
±
Note 8: The Temperature Error specification does not include an additional error of 1˚C, caused by the quantization error.
±
Note 9: The Temperature Error will vary less than 1.0˚C for a variation in V
of 3V to 3.6V from the nominal of 3.3V.
CC
Note 10: Quiescent current will not increase substantially with an active SMBus.
Note 11: This specification is provided only to indicate how often temperature data is updated. The LM84 can be read at any time without regard to conversion state
(and will yield last conversion result).
Note 12: Default values set at power up.
Note 13: Holding the SMBData and/or SMBCLK lines Low for a time interval greater than t
will cause the LM84 to reset SMBData and SMBCLK to the IDLE
TIMEOUT
state of an SMBus communication (SMBCLK and SMBData set High).
www.national.com
8
Logic Electrical Characteristics (Continued)
DS100961-5
FIGURE 2. Temperature-to-Digital Transfer Function (Non-linear scale for clarity)
1.0 Functional Description
The LM84 temperature sensor incorporates a band-gap type
temperature sensor using a Local or Remote diode and an
8-bit ADC (Delta-Sigma Analog-to-Digital Converter). The
LM84 is compatible with the serial SMBus and I2C inter-
faces. Digital comparators compare Local and Remote read-
ings to user-programmable setpoints (LT_CRIT and
RT_CRIT). Activation of the T_CRIT_A output indicates that
a temperature reading is greater than the limit preset in a
T_CRIT register.
1.1 T_CRIT_A OUTPUT, T_CRIT LIMITS
T_CRIT_A is activated when the Local temperature reading
is greater than the limit preset in the local critical temperature
setpoint register (LT_CRIT) or when the Remote tempera-
ture reading is greater than the limit preset in the remote
critical temperature setpoint register (RT_CRIT), as shown in
Figure 3. The T_CRIT_A mask bit (bit 7 of the Configuration
Register) when set will disable the T_CRIT_A output.
DS100961-6
FIGURE 3. T_CRIT_A Temperature Response Diagram
1.2 POWER-ON RESET DEFAULT STATES
LM84 always powers up to these known default states:
1. Local Temperature set to 0˚C
The Status Register can be read to determine which event
caused the alarm. A bit in the Status Register is set high to
indicate T_CRIT temperature alarm, see Section 1.8.3.
2. Remote Temperature set to 0˚C until the LM84 senses a
diode present or open circuit on the D+ and D− input
pins.
Local and remote temperature diodes are sampled alter-
nately by the A/D converter. The T_CRIT_A output and the
Status Register flags are updated at the completion of a
conversion, which takes approximately 60 ms. T_CRIT_A
and the Status Register flags are reset only after the Status
Register is read and if the temperature is below the setpoint.
3. Status Register set to 00h.
4. Command Register set to 00h; T_CRIT_A enabled.
5. Local and Remote T_CRIT set to 127˚C
9
www.national.com
minimize any local temperature reading errors due to self
heating of the LM84. The maximum resistance of the pull-up,
based on LM84 specification for High Level Output Current,
to provide a 2V high level, is 30 kΩ.
1.0 Functional Description (Continued)
1.3 SMBus INTERFACE
The LM84 operates as a slave on the SMBus, so the
SMBCLK line is an input (no clock is generated by the LM84)
and the SMBData line is bi-directional. According to SMBus
specifications, the LM84 has a 7-bit slave address. Bit 4 (A3)
of the slave address is hard wired inside the LM84 to a 1.
The remainder of the address bits are controlled by the
address select pins ADD1 and ADD0, and are set by con-
necting these pins to ground for a low, (0) , to VCC for a high,
(1), or left floating (TRI-LEVEL).
1.6 DIODE FAULT DETECTION
Before each remote conversion the LM84 goes through an
external diode fault detection sequence. If the D+ input is
shorted to VCC or floating then the temperature reading will
be +127˚C, bit 2 (OPEN) of the Status Register will be set. If
the Remote T_CRIT setpoint is set to less than +127˚C then
bit 4 (RTCRIT) of the Status Register will be set which will
activate the T_CRIT_A output, if enabled. If D+ is shorted to
GND or D−, the temperature reading will be 0˚C and bit 2 of
the Status Register will not be set.
Therefore, the complete slave address is:
A6
A5
A4
A3
A2
A1
A0
MSB
LSB
and is selected as follows:
Address Select Pin State
LM84 SMBus
Slave Address
A6:A0 binary
001 1000
ADD0
ADD1
0
0
0
TRI-LEVEL
001 1001
0
1
001 1010
TRI-LEVEL
0
010 1001
TRI-LEVEL
TRI-LEVEL
010 1010
TRI-LEVEL
1
010 1011
1
1
1
0
100 1100
TRI-LEVEL
1
100 1101
100 1110
The LM84 latches the state of the address select pins during
the first read or write on the SMBus. Changing the state of
the address select pins after the first read or write to any
device on the SMBus will not change the slave address of
the LM84.
1.4 TEMPERATURE DATA FORMAT
Temperature data can be read from the Local Temperature,
Remote Temperature, and T_CRIT setpoint registers. Tem-
perature data can only be written to the T_CRIT setpoint
registers. Temperature data is represented by an 8-bit, two’s
complement byte with an LSB (Least Significant Bit) equal to
1˚C:
Temperature
Digital Output
Binary
Hex
7Dh
19h
01h
00h
FFh
E7h
C9h
+125˚C
+25˚C
+1˚C
0111 1101
0001 1001
0000 0001
0000 0000
1111 1111
1110 0111
1100 1001
0˚C
−1˚C
−25˚C
−55˚C
1.5 OPEN-DRAIN OUTPUTS
SMBData and T_CRIT_A outputs are open-drain and do not
have internal pull-ups. A “high” level will not be observed on
these pins until pull-up current is provided from some exter-
nal source, typically a pull-up resistor. Choice of resistor
value depends on many system factors but, in general, the
pull-up resistor should be as large as possible. This will
www.national.com
10
1.0 Functional Description (Continued)
1.7 COMMUNICATING with the LM84
DS100961-9
There are 10 data registers in the LM84, selected by the
Command Register. At power-up the Command Register is
set to “00”, the location for the Read Local Temperature
Register. The Command Register latches whatever the last
location it was set to. Reading the Status Register resets
T_CRIT_A. All registers are predefined as read only or write
only. Read and write registers with the same function contain
mirrored data.
1.7.1 SMBus TIMEOUT
The LM84 SMBus interface circuitry will be reset to the
SMBus idle state if the SMBData or SMBCLK lines are held
low for more than 40 ms. The LM84 may or may not reset the
state SMBData or SMBCLK if either of these lines are held
low between 25 ms and 40 ms. Holding SMBData or SMB-
CLK low for less than or equal to 25 ms will not reset the
interface circuitry. The LM84 has a built-in internal timer to
guarantee that the interface is reset if the SMBData line were
to get stuck low. This can commonly occur when the master
is reset while the slave is transmitting low. This enhance-
ment to the SMBus TIMEOUT specification ensures error
free performance even in remote systems where complete
power supply shutdown, for reset, is a nuisance. This would
have to occur since many cost effective temperature sensors
such as the LM84 do not have a pin dedicated for reset.
A Write to the LM84 will always include the address byte and
the command byte. A write to any register requires one data
byte.
Reading the LM84 can take place either of two ways:
1. If the location latched in the Command Register is cor-
rect (most of the time it is expected that the Command
Register will point to one of the Read Temperature Reg-
isters because that will be the data most frequently read
from the LM84), the read can simply consist of an ad-
dress byte, followed by retrieving the data byte.
2. If the Command Register needs to be set, then an
address byte, command byte, repeat start, and another
address byte will accomplish a read.
The data byte has the most significant bit first. At the end of
a read, the LM84 can accept either Acknowledge or No
Acknowledge from the Master (No Acknowledge is typically
used as a signal for the slave that the Master has read its
last byte).
11
www.national.com
1.0 Functional Description (Continued)
1.8 LM84 REGISTERS
1.8.1 COMMAND REGISTER
Selects which registers will be read from or written to. Data for this register should be transmitted during the Command Byte of
the SMBus write communication.
P7
P6
P5
P4
P3
P2
P1
P0
0
0
0
0
Command Select
P0-P7: Command Select:
Command Se-
lect Address
Power On Default State
Register Name
Register Function
<
>
<
>
<
>
P7:P0 hex
D7:D0 binary
D7:D0 deci-
mal
0
00h
01h
02h
03h
04h
05h
07h
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0111 1111
0111 1111
RLT
RRT
RS
Read Local Temperature
Read Remote Temperature
Read Status
0
0
0
RC
Read Configuration
0
RMID
RLCS
RRCS
Manufacturers ID
127
127
Read Local T_CRIT Setpoint
Read Remote T_CRIT
Setpoint
09h
0Bh
0Dh
0000 0000
0111 1111
0111 1111
0
WC
Write Configuration
127
127
WLCS
WRCS
Write Local T_CRIT Setpoint
Write Remote T_CRIT
Setpoint
1.8.2 LOCAL and REMOTE TEMPERATURE REGISTERS
(Read Only Address 00h and 01h):
D7
D6
D5
D4
D3
D2
D1
D0
MSB
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
LSB
D7–D0: Temperature Data. One LSB = 1˚C. Two’s complement format.
1.8.3 STATUS REGISTER
(Read Only Address 02h):
D7
D6
D5
D4
D3
D2
D1
D0
0
LTCRIT
0
RTCRIT
0
OPEN
0
0
Power up default is with all bits “0” (zero).
D2: OPEN: When set to 1 indicates a Remote Diode disconnect.
D4: RTCRIT: When set to 1 indicates an RT_CRIT alarm.
D6: LTCRIT: When set to 1 indicates an LT_CRIT alarm.
D7, D5, D3, D1–D0: These bits are always set to 0.
1.8.4 Manufacturers ID Register
(Read Address 04h) Default value 00h.
1.8.5 CONFIGURATION REGISTER
(Read Address 03h /Write Address 09h):
D7
D6
D5
D4
D3
D2
D1
D0
T_CRIT_A
mask
0
0
0
0
0
0
0
Power up default is with all bits “0” (zero).
D7: T_CRIT_A mask: When set to 1 T_CRIT_A interrupts are masked.
D6–D0: These bits are always set to 0. A write of 1 will return a 0 when read.
www.national.com
12
1.0 Functional Description (Continued)
1.8.6 LOCAL AND REMOTE T_CRIT REGISTERS
(Read/Write):
D7
D6
D5
D4
D3
D2
D1
D0
MSB
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
LSB
D7–D0: RT_CRIT and LT_CRIT setpoint temperature data. Power up default is LT_CRIT = RT_CRIT = 127˚C.
2.0 SMBus Timing Diagrams
DS100961-10
(a) Serial Bus Write to the internal Command Register followed by a the Data Byte
DS100961-11
(b) Serial Bus Write to the internal Command Register
DS100961-12
(c) Serial Bus Read from a Register with the internal Command Register preset to desired value.
FIGURE 4. Serial Bus Timing Diagrams
13
www.national.com
3.0 Application Hints
The LM84 can be applied easily in the same way as other
integrated-circuit temperature sensors, and its remote diode
sensing capability allows it to be used in new ways as well.
It can be soldered to a printed circuit board, and because the
path of best thermal conductivity is between the die and the
pins, its temperature will effectively be that of the printed
circuit board lands and traces soldered to the LM84’s pins.
This presumes that the ambient air temperature is almost the
same as the surface temperature of the printed circuit board;
if the air temperature is much higher or lower than the
surface temperature, the actual temperature of the of the
LM84 die will be at an intermediate temperature between the
surface and air temperatures. Again, the primary thermal
conduction path is through the leads, so the circuit board
temperature will contribute to the die temperature much
more strongly than will the air temperature.
where:
•
η is the non-ideality factor of the process the diode is
manufactured on,
•
•
•
•
q is the electron charge,
k is the Boltzmann’s constant,
N is the current ratio,
T is the absolute temperature in ˚K.
The temperature sensor then measures ∆VBE and converts
to digital data. In this equation, k and q are well defined
universal constants, and N is a parameter controlled by the
temperature sensor. The only other parameter is η, which
depends on the diode that is used for measurement. Since
∆VBE is proportional to both η and T, the variations in η
cannot be distinguished from variations in temperature.
Since the non-ideality factor is not controlled by the tempera-
ture sensor, it will directly add to the inaccuracy of the
sensor. For the Pentium II Intel specifies a 1% variation in
η from part to part. As an example, assume a temperature
sensor has an accuracy specification of 3˚C at room tem-
perature of 25˚C and the process used to manufacture the
To measure temperature external to the LM84’s die, use a
remote diode. This diode can be located on the die of a
target IC, allowing measurement of the IC’s temperature,
independent of the LM84’s temperature. The LM84 has been
optimized to measure the remote diode of a Pentium II
processor as shown in Figure 5. A discrete diode can also be
used to sense the temperature of external objects or ambient
air. Remember that a discrete diode’s temperature will be
affected, and often dominated, by the temperature of its
leads.
±
±
±
diode has a non-ideality variation of 1%. The resulting
accuracy of the temperature sensor at room temperature will
be:
± ± ±
3˚C + ( 1% of 298˚K) = 6˚C.
TACC
=
The additional inaccuracy in the temperature measurement
caused by η, can be eliminated if each temperature sensor is
calibrated with the remote diode that it will be paired with.
3.2 PCB LAYOUT for MINIMIZING NOISE
In a noisy environment, such as a processor mother board,
layout considerations are very critical. Noise induced on
traces running between the remote temperature diode sen-
sor and the LM84 can cause temperature conversion errors.
The following guidelines should be followed:
1. Place a 0.1 µF power supply bypass capacitor as close
as possible to the VCC pin and the recommended 2.2 nF
capacitor as close as possible to the D+ and D− pins.
Make sure the traces to the 2.2 nF capacitor are
matched.
2. Ideally, the LM84 should be placed within 10 cm of the
Processor diode pins with the traces being as straight,
short and identical as possible.
3. Diode traces should be surrounded by a GND guard ring
to either side, above and below if possible. This GND
guard should not be between the D+ and D− lines. In the
event that noise does couple to the diode lines it would
be ideal if it is coupled common mode. That is equally to
the D+ and D− lines.(See Figure 6)
DS100961-16
Pentium Temperature vs LM84 Temperature Reading
Most silicon diodes do not lend themselves well to this
application. It is recommended that a 2N3904 transistor
base emitter junction be used with the collector tied to the
base.
4. Avoid routing diode traces in close proximity to power
supply switching or filtering inductors.
A diode connected 2N3904 approximates the junction avail-
able on a Pentium microprocessor for temperature measure-
ment. Therefore, the LM84 can sense the temperature of this
diode effectively.
5. Avoid running diode traces close to or parallel to high
speed digital and bus lines. Diode traces should be kept
at least 2 cm. apart from the high speed digital traces.
6. If it is necessary to cross high speed digital traces, the
diode traces and the high speed digital traces should
cross at a 90 degree angle.
3.1 ACCURACY EFFECTS OF DIODE NON-IDEALITY
FACTOR
The technique used in today’s remote temperature sensors
is to measure the change in VBE at two different operating
points of a diode. For a bias current ratio of N:1, this differ-
ence is given as:
www.national.com
14
with the sense diode. For the Pentium II this would be
pin A14.
3.0 Application Hints (Continued)
7. The ideal place to connect the LM84’s GND pin is as
close as possible to the Processors GND associated
DS100961-15
FIGURE 6. Recommended Diode Trace Layout
Noise on the digital lines, overshoot greater than VCC and
undershoot less than GND, may prevent successful SMBus
communication with the LM84. SMBus no acknowledge is
the most common symptom, causing unnecessary traffic on
the bus. Although, the SMBus maximum frequency of com-
munication is rather low (400 kHz max) care still needs to be
taken to ensure proper termination within a system with
multiple parts on the bus and long printed circuit board
traces.
4.0 Typical Applications
DS100961-17
Using a Diode Connected 2N3904 as a Remote Temperture Sensing Element
15
www.national.com
Physical Dimensions inches (millimeters) unless otherwise noted
16-Lead QSOP Package
Order Number LM84BIMQA, LM84BIMQAX, LM84CIMQA or LM84CIMQAX
NS Package Number MQA16
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Corporation
Americas
Tel: 1-800-272-9959
Fax: 1-800-737-7018
Email: support@nsc.com
National Semiconductor
Europe
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
Fax: +49 (0) 180-530 85 86
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
Email: ap.support@nsc.com
www.national.com
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Audio
Applications
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
www.ti.com/industrial
www.ti.com/medical
www.ti.com/security
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
Medical
Security
Logic
Space, Avionics and Defense www.ti.com/space-avionics-defense
Transportation and Automotive www.ti.com/automotive
Power Mgmt
Microcontrollers
RFID
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
Video and Imaging
www.ti.com/video
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated
相关型号：
LM84BIMQAX/NOPB
Switch/Digital Output Temperature Sensor, DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 5Cel, RECTANGULAR, SURFACE MOUNT, QSOP-16
NSC
©2020 ICPDF网 联系我们和版权申明