LM95221 [TI]
Dual Remote Diode Digital Temperature Sensor with SMBus Interface;
| 型号： | LM95221 |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | Dual Remote Diode Digital Temperature Sensor with SMBus Interface |
| 文件： | 总25页 (文件大小：1006K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
LM95221
www.ti.com
SNIS134B –MAY 2004–REVISED MARCH 2013
LM95221 Dual Remote Diode Digital Temperature Sensor with SMBus Interface
Check for Samples: LM95221
1
FEATURES
APPLICATIONS
2
•
Accurately Senses Die Temperature of Remote
ICs or Diode Junctions
•
Processor/Computer System Thermal
Management (e.g. Laptop, Desktop,
Workstations, Server)
•
•
•
Remote Diode Fault Detection
On-board Local Temperature Sensing
Remote Temperature Readings
•
•
Electronic Test Equipment
Office Electronics
–
–
0.125°C LSb
DESCRIPTION
10-bits Plus Sign or 11-bits Programmable
Resolution
The LM95221 is a dual remote diode temperature
sensor in an 8-lead VSSOP package. The 2-wire
serial interface of the LM95221 is compatible with
SMBus 2.0. The LM95221 can sense three
temperature zones, it can measure the temperature
of its own die as well as two diode connected
transistors. The diode connected transistors can be a
thermal diode as found in Pentium and AMD
processors or can simply be a diode connected
MMBT3904 transistor. The LM95221 resolution
format for remote temperature readings can be
programmed to be 10-bits plus sign or 11-bits
unsigned. In the unsigned mode the LM95221 remote
diode readings can resolve temperatures above
127°C. Local temperature readings have a resolution
of 9-bits plus sign.
–
11-bits Resolves Temperatures Above
127°C
•
Local Temperature Readings
–
–
0.25°C
9-bits Plus Sign
•
•
Status Register Support
Programmable Conversion Rate Allows User
Optimization of Power Consumption
•
•
Shutdown Mode One-shot Conversion Control
SMBus 2.0 Compatible Interface, Supports
TIMEOUT
•
8-pin VSSOP Package
The temperature of any ASIC can be accurately
determined using the LM95221 as long as
a
KEY SPECIFICATIONS
dedicated diode (semiconductor junction) is available
on the target die. The LM95221 remote sensor
accuracy of ±1°C is factory trimmed for a series
resistance of 2.7 ohms and 1.008 non-ideality factor.
•
Local Temperature Accuracy
TA = 0°C to 85°C ± 3.0°C (max)
Remote Diode Temperature Accuracy
–
•
–
TA = 30°C to 50°C, TD = 45°C to 85°C
±1.0 °C (Max)
–
TA = 0°C to 85°C, TD = 25°C to 140°C
±3.0°C (Max)
•
•
Supply Voltage 3.0 V to 3.6 V
Supply Current 2 mA (Typ)
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2004–2013, Texas Instruments Incorporated
LM95221
SNIS134B –MAY 2004–REVISED MARCH 2013
www.ti.com
Simplified Block Diagram
3.0V-3.6V
LM95221
Local
Diode Selector
D-S Converter
11-Bit or 10-Bit Plus Sign Remote
D+
D-
Temperature
Sensor
Circuitry
9-bit Plus Sign Local
Remote
Diode1 Selector
D+
D-
Remote
Diode2 Selector
Local
Temperature
Registers
Remote 1
Temperature Temperature
Registers
Remote 2
Revision &
Manufacturer
ID Registers
Configuration
Register
Status
Registrer
Control Logic
Registers
Two-Wire Serial
Interface
SMBDAT
SMBCLK
Connection Diagram
D1+
D1-
D2+
D2-
1
2
3
4
8
7
SMBCLK
SMBDAT
LM95221
V
DD
6
5
GND
Figure 1. VSSOP-8
TOP VIEW
PIN DESCRIPTIONS
Label
Pin #
Function
Typical Connection
D1+
1
Diode Current Source
To Diode Anode. Connected to remote discrete diode-
connected transistor junction or to the diode-connected
transistor junction on a remote IC whose die temperature is
being sensed. A 2.2 nF diode bypass capacitor is
recommended to filter high frequency noise. Place the 2.2 nF
capacitor between and as close as possible to the LM95221's
D+ and D− pins. Make sure the traces to the 2.2 nF capacitor
are matched. Ground this pin if this thermal diode is not used.
D1−
2
3
Diode Return Current Sink
Diode Current Source
To Diode Cathode. A 2.2 nF capacitor is recommended
between D1+ and D1-. Ground this pin if this thermal diode is
not used.
D2+
To Diode Anode. Connected to remote discrete diode-
connected transistor junction or to the diode-connected
transistor junction on a remote IC whose die temperature is
being sensed. A 2.2 nF diode bypass capacitor is
recommended to filter high frequency noise. Place the 2.2 nF
capacitor between and as close as possible to the LM95221's
D+ and D− pins. Make sure the traces to the 2.2 nF capacitor
are matched. Ground this pin if this thermal diode is not used.
D2−
4
Diode Return Current Sink
To Diode Cathode. A 2.2 nF capacitor is recommended
between D2+ and D2-. Ground this pin if this thermal diode is
not used.
GND
VDD
5
6
Power Supply Ground
Ground
Positive Supply Voltage Input
DC Voltage from 3.0 V to 3.6 V. VDD should be bypassed with
a 0.1 µF capacitor in parallel with 100 pF. The 100 pF
capacitor should be placed as close as possible to the power
supply pin. Noise should be kept below 200 mVp-p, a 10 µF
capacitor may be required to achieve this.
SMBDAT
SMBCLK
7
8
SMBus Bi-Directional Data Line, From and to Controller; may require an external pull-up resistor
Open-Drain Output
SMBus Clock Input
From Controller; may require an external pull-up resistor
2
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LM95221
LM95221
www.ti.com
SNIS134B –MAY 2004–REVISED MARCH 2013
Typical Application
+3.3V
Standby
C3*
2.2 nF
R2
1.3k
R1
1.3k
Pentium®
PROCESSOR
4
1
2
3
4
8
D1+
D1-
D2+
D2-
SMBCLK
SMBDAT
SMBCLK
SMBDAT
7
6
5
V
DD
GND
C4*
2.2 nF
C2
0.1 mF
C1*
100 pF
LM95221
SMBus
Master
Q1
MMBT3904
* Note, place close to LM95221 pins.
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings(1)
Supply Voltage
−0.3 V to 6.0 V
−0.5V to 6.0V
Voltage at SMBDAT, SMBCLK
Voltage at Other Pins
−0.3 V to (VDD
+
0.3 V)
D− Input Current
±1 mA
Input Current at All Other Pins(2)
Package Input Current(2)
±5 mA
30 mA
SMBDAT Output Sink Current
Storage Temperature
10 mA
−65°C to +150°C
215°C
Soldering Information, Lead Temperature
VSSOP-8 Package(3)
Vapor Phase (60 seconds)
Infrared (15 seconds)
220°C
ESD Susceptibility(4)
Human Body Model
Machine Model
2000 V
200 V
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not
apply when operating the device beyond its rated operating conditions.
(2) When the input voltage (VI) at any pin exceeds the power supplies (VI < GND or VI > VDD), the current at that pin should be limited to 5
mA. Parasitic components and or ESD protection circuitry are shown in Figure 3 below for the LM95221's pins. The nominal breakdown
voltage of D4 is 6.5 V. Care should be taken not to forward bias the parasitic diode, D1, present on pins: D1+, D2+, D1−, D2−. Doing so
by more than 50 mV may corrupt the temperature measurements.
(3) See the URL ”http://www.ti.com/packaging/“ for other recommendations and methods of soldering surface mount devices.
(4) Human body model, 100pF discharged through a 1.5kΩ resistor. Machine model, 200pF discharged directly into each pin.
Operating Ratings(1)(2)
Operating Temperature Range
Electrical Characteristics Temperature Range
LM95221CIMM
0°C to +115°C
MIN≤TA≤TMAX
T
0°C≤TA≤+85°C
Supply Voltage Range (VDD
)
+3.0V to +3.6V
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not
apply when operating the device beyond its rated operating conditions.
(2) Thermal resistance junction-to-ambient when attached to a printed circuit board with 2 oz. foil:
— VSSOP-8 = 210°C/W
Copyright © 2004–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LM95221
LM95221
SNIS134B –MAY 2004–REVISED MARCH 2013
www.ti.com
Temperature-to-Digital Converter Characteristic
Unless otherwise noted, these specifications apply for VDD=+3.0Vdc to 3.6Vdc. Boldface limits apply for TA = TJ =
TMIN≤TA≤TMAX; all other limits TA= TJ=+25°C, unless otherwise noted. TJ is the junction temperature of the LM95221. TD is the
junction temperature of the remote thermal diode.
Parameter
Conditions
Typical(1)
Limits(2)
Units
(Limit)
Accuracy Using Local Diode
Accuracy Using Remote Diode, see(4) for Thermal
Diode Processor Type.
TA = 0°C to +85°C(3)
TA = +30°C to
+50°C
±1
±3
±1
°C (max)
°C (max)
TD = +45°C to
+85°C
TA = +0°C to +85°C TD = +25°C to
+140°C
±3
°C (max)
Remote Diode Measurement Resolution
Local Diode Measurement Resolution
11
0.125
10
Bits
°C
Bits
0.25
66
°C
Conversion Time of All Temperatures at the Fastest See(5)
Setting
73
ms (max)
Quiescent Current(6)
SMBus Inactive, 15Hz conversion
2.0
2.6
mA (max)
rate
Shutdown
335
0.7
µA
V
D− Source Voltage
Diode Source Current
(D+ − D−)=+ 0.65V; high-level
188
315
110
20
µA (max)
µA (min)
µA (max)
µA (min)
µA
Low-level
11.75
7
Low-Level Diode Source Current Variation over
Temperature
TA = +30°C to +50°C
+0.5
+1.5
TA = +30°C to +85°C
µA
Power-On Reset Threshold
Measure on VDD input, falling edge
2.4
1.8
V (max)
V (min)
(1) Typicals are at TA = 25°C and represent most likely parametric normal.
(2) Limits are specified to Texas Instruments' AOQL (Average Outgoing Quality Level).
(3) Local temperature accuracy does not include the effects of self-heating. The rise in temperature due to self-heating is the product of the
internal power dissipation of the LM95221 and the thermal resistance. See Note 2 of the Operating Ratings table for the thermal
resistance to be used in the self-heating calculation.
(4) The accuracy of the LM95221CIMM is ensured when using the thermal diode with a non-ideality of 1.008 and series R= 2.7Ω. When
using an MMBT3904 type transistor as the thermal diode the error band will be offset by -3.25°C
(5) This specification is provided only to indicate how often temperature data is updated. The LM95221 can be read at any time without
regard to conversion state (and will yield last conversion result).
(6) Quiescent current will not increase substantially with an SMBus.
4
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LM95221
LM95221
www.ti.com
SNIS134B –MAY 2004–REVISED MARCH 2013
Logic Electrical Characteristics
DIGITAL DC CHARACTERISTICS
Unless otherwise noted, these specifications apply for VDD=+3.0 to 3.6 Vdc. Boldface limits apply for TA = TJ = TMIN to
TMAX; all other limits TA= TJ=+25°C, unless otherwise noted.
Symbol
Parameter
Conditions
Typical(1)
Limits(2)
Units
(Limit)
SMBDAT, SMBCLK INPUTS
VIN(1)
Logical “1” Input Voltage
Logical “0”Input Voltage
2.1
0.8
V (min)
V (max)
mV
VIN(0)
VIN(HYST)
SMBDAT and SMBCLK Digital Input
Hysteresis
400
IIN(1)
IIN(0)
CIN
Logical “1” Input Current
Logical “0” Input Current
Input Capacitance
VIN = VDD
0.005
−0.005
5
±10
±10
µA (max)
µA (max)
pF
VIN = 0 V
SMBDAT OUTPUT
IOH
High Level Output Current
SMBus Low Level Output Voltage
VOH = VDD
10
µA (max)
V (max)
VOL
IOL = 4mA
IOL = 6mA
0.4
0.6
(1) Typicals are at TA = 25°C and represent most likely parametric normal.
(2) Limits are specified to Texas Instruments' AOQL (Average Outgoing Quality Level).
SMBus DIGITAL SWITCHING CHARACTERISTICS
Unless otherwise noted, these specifications apply for VDD=+3.0 Vdc to +3.6 Vdc, CL (load capacitance) on output lines = 80
pF. Boldface limits apply for TA = TJ = TMIN to TMAX; all other limits TA = TJ = +25°C, unless otherwise noted.
The switching characteristics of the LM95221 fully meet or exceed the published specifications of the SMBus version 2.0. The
following parameters are the timing relationships between SMBCLK and SMBDAT signals related to the LM95221. They
adhere to but are not necessarily the SMBus bus specifications.
Symbol
Parameter
Conditions
Typical(1)
Limits(2)
Units
(Limit)
fSMB
SMBus Clock Frequency
100
10
kHz (max)
kHz (min)
tLOW
SMBus Clock Low Time
from VIN(0)max to VIN(0)max
4.7
25
µs (min)
ms (max)
tHIGH
tR,SMB
tF,SMB
tOF
SMBus Clock High Time
SMBus Rise Time
SMBus Fall Time
from VIN(1)min to VIN(1)min
4.0
µs (min)
µs (max)
µs (max)
ns (max)
See(3)
See(4)
1
0.3
Output Fall Time
CL = 400pF,
IO = 3mA(4)
250
tTIMEOUT SMBDAT and SMBCLK Time Low for Reset of
Serial Interface(5)
25
35
ms (min)
ms (max)
tSU;DAT
tHD;DAT
Data In Setup Time to SMBCLK High
Data Out Stable after SMBCLK Low
250
ns (min)
300
900
ns (min)
ns (max)
tHD;STA
Start Condition SMBDAT Low to SMBCLK Low
(Start condition hold before the first clock falling
edge)
100
ns (min)
tSU;STO
tSU;STA
Stop Condition SMBCLK High to SMBDAT Low
(Stop Condition Setup)
100
0.6
ns (min)
µs (min)
SMBus Repeated Start-Condition Setup Time,
SMBCLK High to SMBDAT Low
(1) Typicals are at TA = 25°C and represent most likely parametric normal.
(2) Limits are specified to Texas Instruments' AOQL (Average Outgoing Quality Level).
(3) The output rise time is measured from (VIN(0)max + 0.15V) to (VIN(1)min − 0.15V).
(4) The output fall time is measured from (VIN(1)min - 0.15V) to (VIN(1)min + 0.15V).
(5) Holding the SMBDAT and/or SMBCLK lines Low for a time interval greater than tTIMEOUT will reset the LM95221's SMBus state machine,
therefore setting SMBDAT and SMBCLK pins to a high impedance state.
Copyright © 2004–2013, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: LM95221
LM95221
SNIS134B –MAY 2004–REVISED MARCH 2013
www.ti.com
SMBus DIGITAL SWITCHING CHARACTERISTICS
Unless otherwise noted, these specifications apply for VDD=+3.0 Vdc to +3.6 Vdc, CL (load capacitance) on output lines = 80
pF. Boldface limits apply for TA = TJ = TMIN to TMAX; all other limits TA = TJ = +25°C, unless otherwise noted.
The switching characteristics of the LM95221 fully meet or exceed the published specifications of the SMBus version 2.0. The
following parameters are the timing relationships between SMBCLK and SMBDAT signals related to the LM95221. They
adhere to but are not necessarily the SMBus bus specifications.
Symbol
Parameter
Conditions
Typical(1)
Limits(2)
Units
(Limit)
tBUF
SMBus Free Time Between Stop and Start
Conditions
1.3
µs (min)
tLOW
tR
tF
VIH
SMBCLK
VIL
tHD;STA
tSU;STA
tHIGH
tSU;STO
tBUF
tSU;DAT
tHD;DAT
VIH
SMBDATV
IL
P
S
P
Figure 2. SMBus Communication
Pin
PIN #
D1
D2
D3
D4
D5
D6
D7
R1
SNP
ESD
Name
CLAMP
VDD
1
2
3
4
6
7
8
x
x
x
x
x
x
x
x
x
x
x
x
D1+
x(1)
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
D1−
x
x
D2+
x
D2-
x
SMBDAT
SMBCLK
x
x
(1) Note: An “x” indicates that the component exists for the designated pin. SNP refers to a snap-back device.
V+
D1
D3
D4
R1
D6
I/O
D2
ESD
Clamp
SNP
D5
D7
GND
Figure 3. ESD Protection Input Structure
6
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LM95221
LM95221
www.ti.com
SNIS134B –MAY 2004–REVISED MARCH 2013
Typical Performance Characteristics
Remote Temperature Reading Sensitivity to Thermal
Diode Filter Capacitance
Thermal Diode Capacitor or PCB Leakage Current Effect
Remote Diode Temperature Reading
Figure 4.
Figure 5.
Conversion Rate Effect on Average Power Supply Current
Figure 6.
Copyright © 2004–2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: LM95221
LM95221
SNIS134B –MAY 2004–REVISED MARCH 2013
www.ti.com
FUNCTIONAL DESCRIPTION
The LM95221 is a digital sensor that can sense the temperature of 3 thermal zones using a sigma-delta analog-
to-digital converter. It can measure its local die temperature and the temperature of two diode connected
MMBT3904 transistors using a ΔVbe temperature sensing method. The 2-wire serial interface, of the LM95221, is
compatible with SMBus 2.0 and I2C. Please see the SMBus 2.0 specification for a detailed description of the
differences between the I2C bus and SMBus.
The temperature conversion rate is programmable to allow the user to optimize the current consumption of the
LM95221 to the system requirements. The LM95221 can be placed in shutdown to minimize power consumption
when temperature data is not required. While in shutdown, a 1-shot conversion mode allows system control of
the conversion rate for ultimate flexibility.
The remote diode temperature resolution is eleven bits and is programmable to 11-bits unsigned or 10-bits plus
sign. The least-significant-bit (LSb) weight for both resolutions is 0.125°C. The unsigned resolution allows the
remote diodes to sense temperatures above 127°C. Local temperature resolution is not programmable and is
always 9-bits plus sign and has a 0.25°C LSb.
The LM95221 remote diode temperature accuracy will be trimmed for the thermal diode of a Prescott processor
and the accuracy will be ensured only when using this diode.
Diode fault detection circuitry in the LM95221 can detect the presence of a remote diode: whether D+ is shorted
to VDD, D- or ground, or whether D+ is floating.
The LM95221 register set has an 8-bit data structure and includes:
1. Most-Significant-Byte (MSB) Local Temperature Register
2. Least-Significant-Byte (LSB) Local Temperature Register
3. MSB Remote Temperature 1 Register
4. LSB Remote Temperature 1 Register
5. MSB Remote Temperature 2 Register
6. LSB Remote Temperature 2 Register
7. Status Register: busy, diode fault
8. Configuration Register: resolution control, conversion rate control, standby control
9. 1-shot Register
10. Manufacturer ID
11. Revision ID
CONVERSION SEQUENCE
The LM95221 takes approximately 66 ms to convert the Local Temperature, Remote Temperature 1 and 2, and
to update all of its registers. Only during the conversion process the busy bit (D7) in the Status register (02h) is
high. These conversions are addressed in a round robin sequence. The conversion rate may be modified by the
Conversion Rate bits found in the Configuration Register (03h). When the conversion rate is modified a delay is
inserted between conversions, the actual conversion time remains at 66ms (26 ms for each remote and 14 ms
for local). Different conversion rates will cause the LM95221 to draw different amounts of supply current as
shown in Figure 7.
8
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LM95221
LM95221
www.ti.com
SNIS134B –MAY 2004–REVISED MARCH 2013
Figure 7. Conversion Rate Effect on Power Supply Current
POWER-ON-DEFAULT STATES
LM95221 always powers up to these known default states. The LM95221 remains in these states until after the
first conversion.
1. Command Register set to 00h
2. Local Temperature set to 0°C
3. Remote Diode Temperature set to 0°C until the end of the first conversion
4. Status Register depends on state of thermal diode inputs
5. Configuration register set to 00h; continuous conversion, time = 66ms
SMBus INTERFACE
The LM95221 operates as a slave on the SMBus, so the SMBCLK line is an input and the SMBDAT line is
bidirectional. The LM95221 never drives the SMBCLK line and it does not support clock stretching. According to
SMBus specifications, the LM95221 has a 7-bit slave address. All bits A6 through A0 are internally programmed
and can not be changed by software or hardware. The LM95221 has the following SMBus slave address:
Version
A6
0
A5
1
A4
0
A3
1
A2
0
A1
1
A0
1
LM95221
TEMPERATURE DATA FORMAT
Temperature data can only be read from the Local and Remote Temperature registers .
Remote temperature data is represented by an 11-bit, two's complement word or unsigned binary word with an
LSb (Least Significant Bit) equal to 0.125°C. The data format is a left justified 16-bit word available in two 8-bit
registers. Unused bits will always report "0".
Copyright © 2004–2013, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: LM95221
LM95221
SNIS134B –MAY 2004–REVISED MARCH 2013
www.ti.com
Table 1. 11-bit, 2's complement (10-bit plus sign)
Temperature
Digital Output
Binary
Hex
+125°C
+25°C
+1°C
0111 1101 0000 0000
0001 1001 0000 0000
0000 0001 0000 0000
0000 0000 0010 0000
0000 0000 0000 0000
1111 1111 1110 0000
1111 1111 0000 0000
1110 0111 0000 0000
1100 1001 0000 0000
7D00h
1900h
0100h
0020h
0000h
FFE0h
FF00h
E700h
C900h
+0.125°C
0°C
−0.125°C
−1°C
−25°C
−55°C
Table 2. 11-bit, unsigned binary
Temperature
Digital Output
Binary
Hex
+255.875°C
+255°C
+201°C
+125°C
+25°C
1111 1111 1110 0000
1111 1111 0000 0000
1100 1001 0000 0000
0111 1101 0000 0000
0001 1001 0000 0000
0000 0001 0000 0000
0000 0000 0010 0000
0000 0000 0000 0000
FFE0h
FF00h
C900h
7D00h
1900h
0100h
0020h
0000h
+1°C
+0.125°C
0°C
Local Temperature data is represented by a 10-bit, two's complement word with an LSb (Least Significant Bit)
equal to 0.25°C. The data format is a left justified 16-bit word available in two 8-bit registers. Unused bits will
always report "0". Local temperature readings greater than +127.875°C are not clamped to +127.875°C, they will
roll-over to negative temperature readings.
Temperature
Digital Output
Binary
Hex
+125°C
+25°C
+1°C
0111 1101 0000 0000
0001 1001 0000 0000
0000 0001 0000 0000
0000 0000 0010 0000
0000 0000 0000 0000
1111 1111 1100 0000
1111 1111 0000 0000
1110 0111 0000 0000
1100 1001 0000 0000
7D00h
1900h
0100h
0020h
0000h
FFE0h
FF00h
E700h
C900h
+0.125°C
0°C
−0.25°C
−1°C
−25°C
−55°C
10
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LM95221
LM95221
www.ti.com
SNIS134B –MAY 2004–REVISED MARCH 2013
SMBDAT OPEN-DRAIN OUTPUT
The SMBDAT output is an open-drain output and does not have internal pull-ups. A “high” level will not be
observed on this pin until pull-up current is provided by some external source, typically a pull-up resistor. Choice
of resistor value depends on many system factors but, in general, the pull-up resistor should be as large as
possible without effecting the SMBus desired data rate. This will minimize any internal temperature reading
errors due to internal heating of the LM95221. The maximum resistance of the pull-up to provide a 2.1V high
level, based on LM95221 specification for High Level Output Current with the supply voltage at 3.0V, is
82kΩ(5%) or 88.7kΩ(1%).
DIODE FAULT DETECTION
The LM95221 is equipped with operational circuitry designed to detect fault conditions concerning the remote
diodes. In the event that the D+ pin is detected as shorted to GND, D−, VDD or D+ is floating, the Remote
Temperature reading is –128.000 °C if signed format is selected and +255.875 if unsigned format is selected. In
addition, the appropriate status register bits RD1M or RD2M (D1 or D0) are set.
COMMUNICATING with the LM95221
The data registers in the LM95221 are selected by the Command Register. At power-up the Command Register
is set to “00”, the location for the Read Local Temperature Register. The Command Register latches the last
location it was set to. Each data register in the LM95221 falls into one of four types of user accessibility:
1. Read only
2. Write only
3. Write/Read same address
4. Write/Read different address
A Write to the LM95221 will always include the address byte and the command byte. A write to any register
requires one data byte.
Reading the LM95221 can take place either of two ways:
1. If the location latched in the Command Register is correct (most of the time it is expected that the Command
Register will point to one of the Read Temperature Registers because that will be the data most frequently
read from the LM95221), then the read can simply consist of an address byte, followed by retrieving the data
byte.
2. If the Command Register needs to be set, then an address byte, command byte, repeat start, and another
address byte will accomplish a read.
The data byte has the most significant bit first. At the end of a read, the LM95221 can accept either acknowledge
or No Acknowledge from the Master (No Acknowledge is typically used as a signal for the slave that the Master
has read its last byte). It takes the LM95221 66 ms to measure the temperature of the remote diodes and internal
diode. When retrieving all 11 bits from a previous remote diode temperature measurement, the master must
insure that all 11 bits are from the same temperature conversion. This may be achieved by reading the MSB
register first. The LSB will be locked after the MSB is read. The LSB will be unlocked after being read. If the user
reads MSBs consecutively, each time the MSB is read, the LSB associated with that temperature will be locked
in and override the previous LSB value locked-in.
Copyright © 2004–2013, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: LM95221
LM95221
SNIS134B –MAY 2004–REVISED MARCH 2013
www.ti.com
SMBus Timing Diagrams
1
9
1
9
SMBCLK
SMBDAT
R/W
D7 D6 D5 D4 D3 D2 D1 D0
A6 A5 A4 A3 A2 A1 A0
Ack
by
LM95221
Ack
by
LM95221
Start by
Master
Frame 1
Serial Bus Address Byte
Frame 2
Command Byte
1
9
SMBCLK
(Continued)
SMBDAT
(Continued)
D7 D6 D5 D4 D3 D2 D1 D0
Stop
by
Ack by
LM95221
Master
Frame 3
Data Byte
Figure 8. Serial Bus Write to the internal Command Register followed by a the Data Byte
1
9
1
9
SMBCLK
SMBDAT
R/W
D7 D6 D5 D4 D3 D2 D1 D0
A6 A5 A4 A3 A2 A1 A0
Ack
by
LM95221
Stop
by
Master
Ack by
LM95221
Start by
Master
Frame 1
Frame 2
Serial Bus Address Byte
Command Byte
Figure 9. Serial Bus Write to the Internal Command Register
1
9
1
9
SMBCLK
SMBDAT
D7 D6 D5 D4 D3 D2 D1 D0
A6
A5
A4
A3 A2
A1
A0
R/W
Ack
by
LM95221
NoAck Stop
by by
Master Master
Start by
Master
Frame 1
Frame 2
Serial Bus Address Byte
Data Byte from the LM95221
Figure 10. Serial Bus Read from a Register with the Internal Command Register preset to desired value.
1
9
1
9
SMBCLK
SMBDAT
R/W
D7 D6 D5 D4 D3 D2 D1 D0
A6 A5 A4 A3 A2 A1 A0
Ack
by
LM95221
Ack
by
Repeat
Start by
Start by
Master
LM95221 Master
Frame 1
Serial Bus Address Byte
Frame 2
Command Byte
1
9
1
9
SMBCLK
(Continued)
SMBDAT
(Continued)
D7 D6 D5 D4 D3 D2 D1 D0
A6 A5 A4 A3 A2 A1 A0 R/W
Ack
by
No Ack Stop
by
by
Master Master
LM95221
Frame 3
Serial Bus Address Byte
Frame 4
Data Byte from the LM95221
Figure 11. Serial Bus Write followed by a Repeat Start and Immediate Read
12
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LM95221
LM95221
www.ti.com
SNIS134B –MAY 2004–REVISED MARCH 2013
SERIAL INTERFACE RESET
In the event that the SMBus Master is RESET while the LM95221 is transmitting on the SMBDAT line, the
LM95221 must be returned to a known state in the communication protocol. This may be done in one of two
ways:
1. When SMBDAT is LOW, the LM95221 SMBus state machine resets to the SMBus idle state if either
SMBDAT or SMBCLK are held low for more than 35ms (tTIMEOUT). Note that according to SMBus
specification 2.0 all devices are to timeout when either the SMBCLK or SMBDAT lines are held low for 25-
35ms. Therefore, to insure a timeout of all devices on the bus the SMBCLK or SMBDAT lines must be held
low for at least 35ms.
2. When SMBDAT is HIGH, have the master initiate an SMBus start. The LM95221 will respond properly to an
SMBus start condition at any point during the communication. After the start the LM95221 will expect an
SMBus Address address byte.
ONE-SHOT CONVERSION
The One-Shot register is used to initiate a single conversion and comparison cycle when the device is in standby
mode, after which the device returns to standby. This is not a data register and it is the write operation that
causes the one-shot conversion. The data written to this address is irrelevant and is not stored. A zero will
always be read from this register.
LM95221 Registers
Command register selects which registers will be read from or written to. Data for this register should be
transmitted during the Command Byte of the SMBus write communication.
P7
P6
P5
P4
P3
P2
P1
P0
Command
P0-P7: Command
Table 3. Register Summary
Name
Command
(Hex)
Power-On
Default Value
(Hex)
Read/Write
# of used bits Comments
Status Register
Configuration Register
1-shot
02h
03h
0Fh
-
00h
-
RO
R/W
WO
3
4
-
2 status bits and 1 busy bit
Includes conversion rate control
Activates one conversion for all
3 channels if the chip is in
standby mode (i.e. RUN/STOP
bit = 1). Data transmitted by the
host is ignored by the LM95221.
Local Temperature MSB
10h
11h
12h
20h
21h
22h
FEh
FFh
-
RO
RO
RO
RO
RO
RO
RO
RO
8
8
8
2
3
3
Remote Temperature 1 MSB
Remote Temperature 2 MSB
Local Temperature LSB
Remote Temperature 1 LSB
Remote Temperature 2 LSB
Manufacturer ID
-
-
-
-
All unused bits will report zero
All unused bits will report zero
All unused bits will report zero
-
01h
61h
Revision ID
Copyright © 2004–2013, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: LM95221
LM95221
SNIS134B –MAY 2004–REVISED MARCH 2013
www.ti.com
STATUS REGISTER (Read Only Address 02h)
D7
D6
D5
D4
Reserved
0
D3
D2
D1
D0
Busy
RD2M
RD1M
0
0
0
0
Bits
7
Name
Description
Busy
When set to "1" the part is converting.
Reports "0" when read.
6-2
1
Reserved
Remote diode 2 missing (RD2M)
Remote diode 1 missing (RD1M)
Remote Diode 2 is missing. (i.e. D2+ shorted to VDD, Ground or D2-, or D2+ is
floating). Temperature Reading is FFE0h which converts to 255.875 °C if
unsigned format is selected or 8000h which converts to –128.000 °C if signed
format is selected.
0
Remote Diode 1 is missing. (i.e. D1+ shorted to VDD, Ground or D1-, or D1+ is
floating). Temperature Reading is FFE0h which converts to 255.875 °C if
unsigned format is selected or 8000h which converts to –128.000 °C if signed
format is selected.
CONFIGURATION REGISTER (Read Address 03h / Write Address 03h)
D7
D6
D5
D4
D3
D2
D1
D0
0
RUN/STOP
CR1
CR0
0
R2DF
R1DF
0
Bits
7
Name
Description
Reports "0" when read.
Reserved
RUN/STOP
6
Logic 1 disables the conversion and puts the part in standby mode.
Conversion can be activated by writing to one-shot register.
5-4
Conversion Rate (CR1:CR0)
00: continuous mode 66ms, 15 Hz (typ)
01: converts every 200ms, 5 Hz (typ)
10: converts every 1 second, 1 Hz (typ)
11: converts every 3 seconds, ⅓ Hz (typ)
Note: typically a remote diode conversion takes 26 ms and local conversion
takes 14 ms.
3
2
Reserved
Reports "0" when read.
Remote 2 Data Format (R2DF)
Logic 0: unsigned Temperature format (0 °C to +255.875 °C)
Logic 1: signed Temperature format (-128 °C to +127.875 °C)
1
0
Remote 1 Data Format (R1DF)
Reserved
Logic 0: unsigned Temperature format (0 °C to +255.875 °C)
Logic 1: signed Temperature format (-128 °C to +127.875 °C)
Reports "0" when read.
Power up default is with all bits “0” (zero)
LOCAL and REMOTE MSB and LSB TEMPERATURE REGISTERS
Table 4. Local Temperature MSB (Read Only Address 10h) 9-bit plus sign format(1)
:
BIT
D7
D6
D5
D4
D3
D2
D1
D0
Value
SIGN
64
32
16
8
4
2
1
(1) Temperature Data: LSb = 1°C.
Table 5. Local Temperature LSB (Read Only Address 20h) 9-bit plus sign format(1)
:
BIT
D7
D6
D5
D4
D3
D2
D1
D0
Value
0.5
0.25
0
0
0
0
0
0
(1) Temperature Data: LSb = 0.25°C
14
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LM95221
LM95221
www.ti.com
SNIS134B –MAY 2004–REVISED MARCH 2013
Table 6. Remote Temperature MSB (Read Only Address 11h, 12h) 10 bit plus sign format(1)
:
BIT
D7
D6
D5
D4
D3
D2
D1
D0
Value
SIGN
64
32
16
8
4
2
1
(1) Temperature Data: LSb = 1°C.
Table 7. Remote Temperature MSB (Read Only Address 11h, 12h) 11-bit unsigned format(1)
:
BIT
D7
D6
D5
D4
D3
D2
D1
D0
Value
128
64
32
16
8
4
2
1
(1)
Table 8. Remote Temperature LSB(Read Only Address 21, 22h) 10-bit plus sign or 11-bit unsigned binary
formats(1)
:
BIT
D7
D6
D5
D4
D3
D2
D1
D0
Value
0.5
0.25
0.125
0
0
0
0
0
(1) Temperature Data: LSb = 0.125°C.
For data synchronization purposes, the MSB register should be read first if the user wants to read both MSB and
LSB registers. The LSB will be locked after the MSB is read. The LSB will be unlocked after being read. If the
user reads MSBs consecutively, each time the MSB is read, the LSB associated with that temperature will be
locked in and override the previous LSB value locked-in.
MANUFACTURERS ID REGISTER
(Read Address FEh) The default value is 01h.
DIE REVISION CODE REGISTER
(Read Address FFh) Value to be determined. This register will increment by 1 every time there is a revision to
the die by Texas Instruments.
Applications Hints
The LM95221 can be applied easily in the same way as other integrated-circuit temperature sensors, and its
remote diode sensing capability allows it to be used in new ways as well. It can be soldered to a printed circuit
board, and because the path of best thermal conductivity is between the die and the pins, its temperature will
effectively be that of the printed circuit board lands and traces soldered to the LM95221's pins. This presumes
that the ambient air temperature is almost the same as the surface temperature of the printed circuit board; if the
air temperature is much higher or lower than the surface temperature, the actual temperature of the LM95221 die
will be at an intermediate temperature between the surface and air temperatures. Again, the primary thermal
conduction path is through the leads, so the circuit board temperature will contribute to the die temperature much
more strongly than will the air temperature.
To measure temperature external to the LM95221's die, use a remote diode. This diode can be located on the
die of a target IC, allowing measurement of the IC's temperature, independent of the LM95221's temperature.
The LM95221 has been optimized to measure the remote thermal diode with a non-ideality of 1.008 and a series
resistance of 2.7Ω. The thermal diode on the Pentium 4 processor on the 90 nm process has a typical non-
ideality of 1.011 and a typical series resistance of 3.33Ω. Therefore, when measuring this thermal diode with the
LM95221 a typical offset of +1.5°C will be observed. This offset can be compensated for easily by subracting
1.5°C from the LM95221's readings. A discrete diode can also be used to sense the temperature of external
objects or ambient air. Remember that a discrete diode's temperature will be affected, and often dominated, by
the temperature of its leads.
Most silicon diodes do not lend themselves well to this application. It is recommended that a 2N3904 transistor
base emitter junction be used with the collector tied to the base.
When measuring a diode-connected 2N3904, with an LM95221, an offset of -3.25°C will be observed. This offset
can simply be added to the LM95221's reading:
T2N3904 = TLM95221 + 3.25°C
(1)
Copyright © 2004–2013, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: LM95221
LM95221
SNIS134B –MAY 2004–REVISED MARCH 2013
www.ti.com
DIODE NON-IDEALITY
Diode Non-Ideality Factor Effect on Accuracy
When a transistor is connected as a diode, the following relationship holds for variables VBE, T and If:
Vbe
IF = IS ehV - 1
t
where
k T
q
Vt =
•
•
•
•
•
•
•
•
q = 1.6×10−19 Coulombs (the electron charge),
T = Absolute Temperature in Kelvin
k = 1.38×10−23joules/K (Boltzmann's constant),
η is the non-ideality factor of the process the diode is manufactured on,
IS = Saturation Current and is process dependent,
If= Forward Current through the base emitter junction
VBE = Base Emitter Voltage drop
(2)
(3)
In the active region, the -1 term is negligible and may be eliminated, yielding the following equation:
Vbe
IF = IS ehV
t
In the above equation, η and IS are dependant upon the process that was used in the fabrication of the particular
diode. By forcing two currents with a very controlled ratio (N) and measuring the resulting voltage difference, it is
possible to eliminate the IS term. Solving for the forward voltage difference yields the relationship:
k T
Vbe = h
ln (N)
q
(4)
The voltage seen by the LM95221 also includes the IFRS voltage drop of the series resistance. The non-ideality
factor, η, is the only other parameter not accounted for and depends on the diode that is used for measurement.
Since ΔVBE is proportional to both η and T, the variations in η cannot be distinguished from variations in
temperature. Since the non-ideality factor is not controlled by the temperature sensor, it will directly add to the
inaccuracy of the sensor. For the Pentium 4 and Mobile Pentium Processor-M Intel specifies a ±0.1% variation in
η from part to part. As an example, assume a temperature sensor has an accuracy specification of ±1°C at room
temperature of 25 °C and the process used to manufacture the diode has a non-ideality variation of ±0.1%. The
resulting accuracy of the temperature sensor at room temperature will be:
TACC = ± 1°C + (±0.1% of 298 °K) = ±1.4 °C
(5)
16
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LM95221
LM95221
www.ti.com
SNIS134B –MAY 2004–REVISED MARCH 2013
The additional inaccuracy in the temperature measurement caused by η, can be eliminated if each temperature
sensor is calibrated with the remote diode that it will be paired with.
Processor Family
η, non-ideality
typ
Series R
min
max
Pentium II
1
1
1.0065
1.0173
1.0125
1.0125
Pentium III CPUID 67h
1.0065
Pentium III CPUID
1.0057
1.008
68h/PGA370Socket/Celeron
Pentium 4, 423 pin
Pentium 4, 478 pin
0.9933
0.9933
1.0011
1.0045
1.0045
1.0021
1.0368
1.0368
1.0030
Pentium 4 on 0.13 micron process,
2-3.06GHz
3.64 Ω
Pentium 4 on 90 nm process
Pentium M Processor (Centrino)
MMBT3904
1.011
1.00220
1.003
3.33 Ω
3.06 Ω
1.00151
1.002
1.00289
1.016
AMD Athlon MP model 6
1.008
Compensating for Diode Non-Ideality
In order to compensate for the errors introduced by non-ideality, the temperature sensor is calibrated for a
particular processor. Texas Instruments temperature sensors are always calibrated to the typical non-ideality of a
given processor type. The LM95221 is calibrated for a non-ideality of 1.008 and a series resistance of 2.7Ω.
When a temperature sensor calibrated for a particular processor type is used with a different processor type or a
given processor type has a non-ideality that strays from the typical, errors are introduced.
Temperature errors associated with non-ideality may be reduced in a specific temperature range of concern
through use of an offset calibration accomplished through software.
Please send an email to hardware.monitor.team@nsc.com requesting further information on our recommended
offset value for different processor types.
Copyright © 2004–2013, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links: LM95221
LM95221
SNIS134B –MAY 2004–REVISED MARCH 2013
www.ti.com
PCB LAYOUT FOR MINIMIZING NOISE
Figure 12. Ideal Diode Trace Layout
In a noisy environment, such as a processor mother board, layout considerations are very critical. Noise induced
on traces running between the remote temperature diode sensor and the LM95221 can cause temperature
conversion errors. Keep in mind that the signal level the LM95221 is trying to measure is in microvolts. The
following guidelines should be followed:
1. VDD should be bypassed with a 0.1µF capacitor in parallel with 100pF. The 100pF capacitor should be placed
as close as possible to the power supply pin. A bulk capacitance of approximately 10µF needs to be in the
near vicinity of the LM95221.
2. A 2.2nF diode bypass capacitor is required to filter high frequency noise. Place the 2.2nF capacitor as close
as possible to the LM95221's D+ and D− pins. Make sure the traces to the 2.2nF capacitor are matched.
3. Ideally, the LM95221 should be placed within 10cm of the Processor diode pins with the traces being as
straight, short and identical as possible. Trace resistance of 1Ω can cause as much as 1°C of error. This
error can be compensated by using simple software offset compensation.
4. Diode traces should be surrounded by a GND guard ring to either side, above and below if possible. This
GND guard should not be between the D+ and D− lines. In the event that noise does couple to the diode
lines it would be ideal if it is coupled common mode. That is equally to the D+ and D− lines.
5. Avoid routing diode traces in close proximity to power supply switching or filtering inductors.
6. Avoid running diode traces close to or parallel to high speed digital and bus lines. Diode traces should be
kept at least 2cm apart from the high speed digital traces.
7. If it is necessary to cross high speed digital traces, the diode traces and the high speed digital traces should
cross at a 90 degree angle.
8. The ideal place to connect the LM95221's GND pin is as close as possible to the Processors GND
associated with the sense diode.
9. Leakage current between D+ and GND and between D+ and D− should be kept to a minimum. Thirteen
nano-amperes of leakage can cause as much as 0.2°C of error in the diode temperature reading. Keeping
the printed circuit board as clean as possible will minimize leakage current.
Noise coupling into the digital lines greater than 400mVp-p (typical hysteresis) and undershoot less than 500mV
below GND, may prevent successful SMBus communication with the LM95221. SMBus no acknowledge is the
most common symptom, causing unnecessary traffic on the bus. Although the SMBus maximum frequency of
communication is rather low (100kHz max), care still needs to be taken to ensure proper termination within a
system with multiple parts on the bus and long printed circuit board traces. An RC lowpass filter with a 3db
corner frequency of about 40MHz is included on the LM95221's SMBCLK input. Additional resistance can be
added in series with the SMBDAT and SMBCLK lines to further help filter noise and ringing. Minimize noise
coupling by keeping digital traces out of switching power supply areas as well as ensuring that digital lines
containing high speed data communications cross at right angles to the SMBDAT and SMBCLK lines.
18
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LM95221
LM95221
www.ti.com
SNIS134B –MAY 2004–REVISED MARCH 2013
REVISION HISTORY
Changes from Revision A (March 2013) to Revision B
Page
•
Changed layout of National Data Sheet to TI format .......................................................................................................... 18
Copyright © 2004–2013, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Links: LM95221
PACKAGE OPTION ADDENDUM
www.ti.com
7-Oct-2013
PACKAGING INFORMATION
Orderable Device
LM95221CIMM/NOPB
LM95221CIMMX/NOPB
Status Package Type Package Pins Package
Eco Plan Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
0 to 85
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
ACTIVE
VSSOP
VSSOP
DGK
8
8
1000
Green (RoHS
& no Sb/Br)
CU SN
CU SN
Level-1-260C-UNLIM
T21C
T21C
ACTIVE
DGK
3500
Green (RoHS
& no Sb/Br)
Level-1-260C-UNLIM
0 to 85
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LM95221CIMM/NOPB
VSSOP
DGK
DGK
8
8
1000
3500
178.0
330.0
12.4
12.4
5.3
5.3
3.4
3.4
1.4
1.4
8.0
8.0
12.0
12.0
Q1
Q1
LM95221CIMMX/NOPB VSSOP
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
LM95221CIMM/NOPB
LM95221CIMMX/NOPB
VSSOP
VSSOP
DGK
DGK
8
8
1000
3500
210.0
367.0
185.0
367.0
35.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
相关型号：
LM95231
Precision Dual Remote Diode Temperature Sensor with SMBus Interface and TruTherm⢠Technology
TI
LM95231BIMM
Precision Dual Remote Diode Temperature Sensor with SMBus Interface and TruTherm Technology
NSC
LM95231BIMM
Precision Dual Remote Diode Temperature Sensor with SMBus Interface and TruTherm? Technology 8-VSSOP 0 to 85
TI
LM95231BIMM-1
Precision Dual Remote Diode Temperature Sensor with SMBus Interface and TruTherm Technology
NSC
LM95231BIMM-1
Switch/Digital Output Temperature Sensor, DIGITAL TEMP SENSOR-SERIAL, 13BIT(s), 0.75Cel, SQUARE, SURFACE MOUNT, MSOP-8
TI
LM95231BIMM-1/NOPB
Precision Dual Remote Diode Temperature Sensor with SMBus Interface and TruTherm⢠Technology
TI
©2020 ICPDF网 联系我们和版权申明