LMC7215IM5 [TI]
Micro-Power, Rail-to-Rail CMOS Comparators with Push-Pull/Open-Drain Outputs;
| 型号： | LMC7215IM5 |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | Micro-Power, Rail-to-Rail CMOS Comparators with Push-Pull/Open-Drain Outputs 放大器 光电二极管 |
| 文件： | 总19页 (文件大小：1737K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
LMC7215, LMC7225
www.ti.com
SNOS882E –SEPTEMBER 1999–REVISED MARCH 2013
LMC7215/LMC7215-Q1/LMC7225 Micro-Power, Rail-to-Rail CMOS Comparators with Push-
Pull/Open-Drain Outputs
Check for Samples: LMC7215, LMC7225
1
FEATURES
DESCRIPTION
The LMC7215/LMC7215-Q1/LMC7225 are ultra low
power comparators with a maximum of 1 μA power
supply current. They are designed to operate over a
wide range of supply voltages, from 2V to 8V.
2
(Typical Unless Otherwise Noted)
•
•
•
•
•
•
Ultra Low Power Consumption 0.7 μA
Wide Range of Supply Voltages 2V to 8V
Input Common-Mode Range Beyond V+ and V−
Open Collector and Push-Pull Output
The LMC7215/LMC7215-Q1/LMC7225 have
a
greater than rail-to-rail common mode voltage range.
This is a real advantage in single supply applications.
High Output Current Drive: (@ VS = 5V) 45 mA
The LMC7215 features a push-pull output stage. This
feature allows operation with absolute minimum
amount of power consumption when driving any load.
Propagation Delay (@ VS = 5V, 10 mV
Overdrive) 25 μs
•
•
•
Tiny 5-Pin SOT-23 Package
The LMC7225 features an open drain output. By
connecting an external resistor, the output of the
comparator can be used as a level shifter to any
desired voltage to as high as 15V.
Latch-up Resistance >300 mA
LMC7215-Q1 is an Automotive Grade Product
that is AEC-Q100 Grade 3 Qualified.
The LMC7215/LMC7215-Q1/LMC7225 are designed
for systems where low power consumption is the
critical parameter.
APPLICATIONS
•
•
•
•
•
•
•
•
Laptop Computers
Mobile Phones
Ensured operation over the full supply voltage range
of 2.7V to 5V and rail-to-rail performance makes this
comparator ideal for battery-powered applications.
Metering Systems
Hand-held Electronics
RC Timers
Alarm and Monitoring Circuits
Window Comparators, Multivibrators
Automotive
Connection Diagrams
Figure 1. 8-Pin SOIC (Top View)
Figure 2. 5-Pin SOT-23 (Top View)
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
2
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 1999–2013, Texas Instruments Incorporated
LMC7215, LMC7225
SNOS882E –SEPTEMBER 1999–REVISED MARCH 2013
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
(1)(2)
Absolute Maximum Ratings
ESD Tolerance
(3)
2 kV
V+ +0.3V, V− −0.3V
V+ +0.3V, V− −0.3V
10V
Differential Input Voltage
Voltage at Input/Output Pin
Supply Voltage (V+–V−)
Current at Input Pin
±5 mA
(4)
Current at Output Pin
±30 mA
Current at Power Supply Pin
Lead Temperature
40 mA
(soldering, 10 sec)
260°C
Storage Temperature Range
−65°C to +150°C
150°C
(5)
Junction Temperature
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is intended to be functional, but specific performance is not ensured. For ensured specifications and the test
conditions, see the Electrical Characteristics.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
(3) Human Body Model, applicable std. MIL-STD-883, Method 3015.7. Machine Model, applicable std. JESD22-A115-A (ESD MM std. of
JEDEC)Field-Induced Charge-Device Model, applicable std. JESD22-C101-C (ESD FICDM std. of JEDEC).
(4) Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in
exceeding the maximum allowed junction temperature of 150°C.
(5) The maximum power dissipation is a function of TJ(MAX), θJA, and TA. The maximum allowable power dissipation at any ambient
temperature isPD = (TJ(MAX) − TA)/θJA. All numbers apply for packages soldered directly into a PC board.
(1)
Operating Ratings
Supply Voltage
2V ≤ VCC ≤ 8V
−40°C to +85°C
165°C/W
(2)
Temperature Range
Package Thermal Resistance (θJA
)
8-Pin SOIC
5-Pin SOT-23
325°C/W
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is intended to be functional, but specific performance is not ensured. For ensured specifications and the test
conditions, see the Electrical Characteristics.
(2) The maximum power dissipation is a function of TJ(MAX), θJA, and TA. The maximum allowable power dissipation at any ambient
temperature isPD = (TJ(MAX) − TA)/θJA. All numbers apply for packages soldered directly into a PC board.
2.7V to 5V Electrical Characteristics
Unless otherwise specified, all limits specified for TJ = 25°C, V+ = 2.7V to 5V, V− = 0V, VCM = VO = V+/2. Boldface limits apply
at the temperature extremes.
Symbol
Parameter
Conditions
LMC7215
Limit(2)
LMC7225
Limit(2)
Units
(1)
Typ
1
6
6
mV
VOS
Input Offset Voltage
8
8
max
Input Offset Voltage
Average Drift
TCVOS
2
μV/°C
IB
Input Current
5
1
fA
fA
IOS
Input Offset Current
Common Mode
Rejection Ratio
dB
min
(3)
CMRR
See
80
60
60
(1) Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary
over time and will also depend on the application and configuration. The typical values are not tested and are not specified on shipped
production material.
(2) All limits are specified by testing or statistical analysis.
(3) CMRR measured at VCM = 0V to 2.5V and 2.5V to 5V when VS = 5V, VCM = 0.2V to 1.35V and 1.35V to 2.7V when VS = 2.7V. This
eliminates units that have large VOS at the VCM extremes and low or opposite VOS at VCM = VS/2.
2
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LMC7215 LMC7225
LMC7215, LMC7225
www.ti.com
SNOS882E –SEPTEMBER 1999–REVISED MARCH 2013
2.7V to 5V Electrical Characteristics (continued)
Unless otherwise specified, all limits specified for TJ = 25°C, V+ = 2.7V to 5V, V− = 0V, VCM = VO = V+/2. Boldface limits apply
at the temperature extremes.
Symbol
Parameter
Conditions
V+ = 2.2V to 8V
LMC7215
Limit(2)
LMC7225
Limit(2)
Units
(1)
Typ
90
Power Supply
Rejection Ratio
Voltage Gain
dB
min
PSRR
60
60
AV
140
3.0
dB
V
V+ = 2.7V
2.9
2.7
0.0
0.2
5.2
5.0
−0.2
0.0
1.8
1.7
2.3
2.2
4.6
4.5
0.4
0.5
0.4
0.5
0.4
0.5
2.9
2.7
0.0
0.2
5.2
5.0
−0.2
0.0
NA
CMRR > 50 dB
V+ = 2.7V
min
V
−0.2
5.3
CMRR > 50 dB
V+ = 5.0V
max
V
Input Common-Mode Voltage
Range
CMVR
CMRR > 50 dB
V+ = 5.0V
min
V
−0.3
2.05
2.05
4.8
CMRR > 50 dB
V+ = 2.2V
max
V
IOH = 1.5 mA
V+ = 2.7V
min
V
NA
NA
VOH
Output Voltage High
IOH = 2.0 mA
V+ = 5.0V
min
V
IOH = 4.0 mA
V+ = 2.2V
min
V
0.17
0.17
0.2
0.4
0.5
0.4
0.5
0.4
0.5
NA
NA
IOH = 1.5 mA
V+ = 2.7V
max
V
VOL
Output Voltage Low
IOH = 2.0 mA
V+ = 5.0V
max
V
IOH = 4.0 mA
max
mA
mA
mA
mA
nA
max
ISC+
ISC−
ILeakage
IS
Output Short Circuit Current V+ = 2.7V, Sourcing
15
50
12
30
(4)
V+ = 5.0V, Sourcing
Output Short Circuit Current V+ = 2.7V, Sinking
(4)
V+ = 5.0V, Sinking
V+ = 2.2V
Output Leakage Current
Supply Current
VIN+ = 0.1V, VIN− = 0V,
VOUT = 15V
V+ = 5.0V
0.01
0.7
NA
500
1
1
μA
VIN+ = 5V, VIN− = 0V
1.2
1.2
max
(4) Do not short the output of the LMC7225 to voltages greater than 10V or damage may occur.
AC Electrical Characteristics
Unless otherwise specified, TJ = 25°C, V+ = 5V, V− = 0V, VCM = V+/2
Symbol
Parameter
Conditions
LMC7215
LMC7225
Typ(1) (2)
Units
Typ(1)
1
(2)
(2)
trise
tfall
Rise Time
Fall Time
Overdrive = 10 mV
Overdrive = 10 mV
12.2
0.35
μs
μs
0.4
(1) Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary
over time and will also depend on the application and configuration. The typical values are not tested and are not specified on shipped
production material.
(2) All measurements made at 10 kHz. A 100 kΩ pull-up resistor was used when measuring the LMC7225. CLOAD = 50 pF including the test
jig and scope probe. The rise times of the LMC7225 are a function of the R-C time constant.
Copyright © 1999–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LMC7215 LMC7225
LMC7215, LMC7225
SNOS882E –SEPTEMBER 1999–REVISED MARCH 2013
www.ti.com
AC Electrical Characteristics (continued)
Unless otherwise specified, TJ = 25°C, V+ = 5V, V− = 0V, VCM = V+/2
Symbol
tPHL
Parameter
Conditions
LMC7215
Typ(1)
LMC7225
Typ(1) (2)
Units
Propagation Delay
(High to Low)
See(2) (3)
Overdrive = 10 mV
24
12
17
11
24
12
17
11
24
12
17
11
29
17
22
16
μs
Overdrive = 100 mV
Overdrive = 10 mV
Overdrive = 100 mV
Overdrive = 10 mV
Overdrive = 100 mV
Overdrive = 10 mV
Overdrive = 100 mV
V+ = 2.7V(2) (3)
See(2) (3)
μs
μs
μs
tPLH
Propagation Delay
(Low to High)
V+ = 2.7V(2) (3)
(3) Input step voltage for the propagation measurements is 100 mV.
4
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LMC7215 LMC7225
LMC7215, LMC7225
www.ti.com
SNOS882E –SEPTEMBER 1999–REVISED MARCH 2013
Typical Performance Characteristics
TA= 25°C unless otherwise specified
Supply Current
vs.
Supply Voltage
Prop Delay
vs.
VSUPPLY
Figure 3.
Figure 4.
Prop Delay
vs.
Overdrive
Short Circuit Current
vs.
VSUPPLY
Figure 5.
Figure 6.
Output Voltage
vs.
Output Current
LMC7215
Output Voltage
vs.
Output Current
Figure 7.
Figure 8.
Copyright © 1999–2013, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: LMC7215 LMC7225
LMC7215, LMC7225
SNOS882E –SEPTEMBER 1999–REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics (continued)
TA= 25°C unless otherwise specified
Output Voltage
vs.
Output Voltage
vs.
Output Current
Output Current
LMC7215
Figure 9.
Figure 10.
Output Leakage Current
vs.
Output Leakage Current
vs.
Output Voltage
LMC7225
Output Voltage
LMC7225
Figure 11.
Figure 12.
6
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LMC7215 LMC7225
LMC7215, LMC7225
www.ti.com
SNOS882E –SEPTEMBER 1999–REVISED MARCH 2013
APPLICATION INFORMATION
RESPONSE TIME
Depending upon the amount of overdrive, the delay will typically be between 10 μs to 200 μs. The curve showing
delay vs. overdrive in the " Typical Characteristics" section shows the delay time when the input is preset with
100 mV across the inputs and then is driven the other way by 1 mV to 500 mV.
The transition from high to low or low to high is fast. Typically 1 μs rise and 400 ns fall.
With a small signal input, the comparators will provide a square wave output from sine wave inputs at
frequencies as high as 25 kHz. Figure 13 shows a worst case example where a ±5 mV sine wave is applied to
the input. Note that the output is delayed by almost 180°.
Figure 13.
NOISE
Most comparators have rather low gain. This allows the output to spend time between high and low when the
input signal changes slowly. The result is the output may oscillate between high and low when the differential
input is near zero.
The exceptionally high gain of these comparators, 10,000 V/mV, eliminates this problem. Less then 1 μV of
change on the input will drive the output from one rail to the other rail.
If the input signal is noisy, the output cannot ignore the noise unless some hysteresis is provided by positive
feedback.
Figure 14.
Copyright © 1999–2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: LMC7215 LMC7225
LMC7215, LMC7225
SNOS882E –SEPTEMBER 1999–REVISED MARCH 2013
www.ti.com
INPUT VOLTAGE RANGE
The LMC7215/25 have input voltage ranges that are larger than the supply voltage ensures that signals from
other parts of the system cannot overdrive the inputs. This allows sensing supply current by connecting one input
directly to the V+ line and the other to the other side of a current sense resistor. The same is true if the sense
resistor is in the ground return line.
Sensing supply voltage is also easy by connecting one input directly to the supply.
The inputs of these comparators are protected by diodes to both supplies. This protects the inputs from both
ESD as well as signals that greatly exceed the supply voltages. As a result, current will flow through these
forward biased diodes whenever the input voltage is more than a few hundred millivolts larger than the supplies.
Until this occurs, there is essentially no input current. As a result, placing a large resistor in series with any input
that may be exposed to large voltages, will limit the input current but have no other noticeable effect.
If the input current is limited to less than 5 mA by a series resistor, (see Figure 14), a threshold or zero crossing
detector, that works with inputs from as low as a few millivolts to as high as 5,000V, is made with only one
resistor and the comparator.
INPUTS
As mentioned above, these comparators have near zero input current. This allows very high resistance circuits to
be used without any concern for matching input resistances. This also allows the use of very small capacitors in
R-C type timing circuits. This reduces the cost of the capacitors and amount of board space used.
CAPACITIVE LOADS
The high output current drive allows large capacitive loads with little effect. Capacitive loads as large as 10,000
pF have no effect upon delay and only slow the transition by about 3 μs.
OUTPUT CURRENT
Even though these comparators use less than 1 μA supply current, the outputs are able to drive very large
currents.
The LMC7215 can source up to 50 mA when operated on a 5V supply. Both the LMC7215 and LMC7225 can
sink over 20 mA. (See the graph of Max IO vs. VSUPPLY in the " Typical Characteristics” section.)
This large current handling ability allows driving heavy loads directly. LEDs, beepers and other loads can be
driven easily.
The push-pull output stage of the LMC7215 is a very important feature. This keeps the total system power
consumption to the absolute minimum. The only current consumed is the less than 1 μA supply current and the
current going directly into the load. No power is wasted in a pull-up resistor when the output is low. The
LMC7225 is only recommended where a level shifting function from one logic level to another is desired, where
the LMC7225 is being used as a drop-in lower power replacement for an older comparator or in circuits where
more than one output will be paralleled.
POWER DISSIPATION
The large output current ability makes it possible to exceed the maximum operating junction temperature of 85°C
and possibly even the absolute maximum junction temperature of 150°C.
The thermal resistance of the 8-pin SOIC package is 165°C/W. Shorting the output to ground with a 2.7V supply
will only result in about 5°C rise above ambient.
The thermal resistance of the much smaller 5-Pin SOT-23 package is 325°C/W. With a 2.7V supply, the raise is
only 10.5°C but if the supply is 5V and the short circuit current is 50 mA, this will cause a raise of 41°C in the 8-
Pin SOIC and 81°C in the 5-Pin SOT-23. This should be kept in mind if driving very low resistance loads.
8
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LMC7215 LMC7225
LMC7215, LMC7225
www.ti.com
SNOS882E –SEPTEMBER 1999–REVISED MARCH 2013
SHOOT-THROUGH
Shoot-through is a common occurrence on digital circuits and comparators where there is a push-pull output
stage. This occurs when a signal is applied at the same time to both the N-channel and P-channel output
transistors to turn one off and turn the other on. (See Figure 15.) If one of the output devices responds slightly
faster than the other, the fast one can be turned on before the other has turned off. For a very short time, this
allows supply current to flow directly through both output transistors. The result is a short spike of current drawn
from the supply.
Figure 15.
Figure 16. RS = 100Ω
The LMC7215 produces a small current spike of 300 μA peak for about 400 ns with 2.7V supply and 1.8 mA
peak for 400 ns with a 5V supply. This spike only occurs when the output is going from high to low. It does not
occur when going from low to high. Figure 16 and Figure 17 show what this current pulse looks like on 2.7V and
5V supplies. The upper trace is the output voltage and the lower trace is the supply current as measured with the
circuit in Figure 18.
If the power supply has a very high impedance, a bypass capacitor of 0.01 μF should be more than enough to
minimize the effects of this small current pulse.
Copyright © 1999–2013, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: LMC7215 LMC7225
LMC7215, LMC7225
SNOS882E –SEPTEMBER 1999–REVISED MARCH 2013
www.ti.com
Figure 17. RS = 10Ω
Figure 18.
LATCH-UP
In the past, most CMOS IC's were susceptible to a damaging phenomena known as latch-up. This occurred
when an ESD current spike or other large signal was applied to any of the pins of an IC. The LMC7215 and
LMC7225 both are designed to make them highly resistant to this type of damage. They have passed
qualification tests with input currents on any lead up to 300 mA at temperatures up to 125°C.
SPICE MODELS
For a SPICE model of the LMC7215, LMC7225 and many other op amps and comparators, visit www.ti.com.
10
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LMC7215 LMC7225
LMC7215, LMC7225
www.ti.com
SNOS882E –SEPTEMBER 1999–REVISED MARCH 2013
REVISION HISTORY
Changes from Revision D (March 2013) to Revision E
Page
•
Changed layout of National Data Sheet to TI format .......................................................................................................... 10
Copyright © 1999–2013, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: LMC7215 LMC7225
PACKAGE OPTION ADDENDUM
www.ti.com
8-Oct-2015
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(6)
(3)
(4/5)
LMC7215IM/NOPB
ACTIVE
SOIC
D
8
95
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 85
LMC72
15IM
C02B
C02B
LMC7215IM5
NRND
SOT-23
SOT-23
DBV
DBV
5
5
1000
1000
TBD
Call TI
CU SN
Call TI
-40 to 85
-40 to 85
LMC7215IM5/NOPB
ACTIVE
Green (RoHS
& no Sb/Br)
Level-1-260C-UNLIM
LMC7215IM5X
NRND
SOT-23
SOT-23
DBV
DBV
5
5
3000
3000
TBD
Call TI
CU SN
Call TI
-40 to 85
-40 to 85
C02B
C02B
LMC7215IM5X/NOPB
ACTIVE
Green (RoHS
& no Sb/Br)
Level-1-260C-UNLIM
LMC7215IMX/NOPB
LMC7215QIM5/NOPB
LMC7215QIM5X/NOPB
ACTIVE
ACTIVE
ACTIVE
SOIC
D
8
5
5
2500
1000
3000
Green (RoHS
& no Sb/Br)
CU SN
CU SN
CU SN
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-40 to 85
-40 to 85
-40 to 85
LMC72
15IM
SOT-23
SOT-23
DBV
DBV
Green (RoHS
& no Sb/Br)
C02Q
Green (RoHS
& no Sb/Br)
C02Q
LMC7225IM5
NRND
SOT-23
SOT-23
DBV
DBV
5
5
1000
1000
TBD
Call TI
CU SN
Call TI
-40 to 85
-40 to 85
C03B
C03B
LMC7225IM5/NOPB
ACTIVE
Green (RoHS
& no Sb/Br)
Level-1-260C-UNLIM
LMC7225IM5X/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 85
C03B
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
8-Oct-2015
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF LMC7215, LMC7215-Q1 :
Catalog: LMC7215
•
Automotive: LMC7215-Q1
•
NOTE: Qualified Version Definitions:
Catalog - TI's standard catalog product
•
Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
•
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
2-Sep-2015
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LMC7215IM5
SOT-23
SOT-23
SOT-23
SOT-23
SOIC
DBV
DBV
DBV
DBV
D
5
5
5
5
8
5
5
5
5
5
1000
1000
3000
3000
2500
1000
3000
1000
1000
3000
178.0
178.0
178.0
178.0
330.0
178.0
178.0
178.0
178.0
178.0
8.4
8.4
8.4
8.4
12.4
8.4
8.4
8.4
8.4
8.4
3.2
3.2
3.2
3.2
6.5
3.2
3.2
3.2
3.2
3.2
3.2
3.2
3.2
3.2
5.4
3.2
3.2
3.2
3.2
3.2
1.4
1.4
1.4
1.4
2.0
1.4
1.4
1.4
1.4
1.4
4.0
4.0
4.0
4.0
8.0
4.0
4.0
4.0
4.0
4.0
8.0
8.0
8.0
8.0
12.0
8.0
8.0
8.0
8.0
8.0
Q3
Q3
Q3
Q3
Q1
Q3
Q3
Q3
Q3
Q3
LMC7215IM5/NOPB
LMC7215IM5X
LMC7215IM5X/NOPB
LMC7215IMX/NOPB
LMC7215QIM5/NOPB
SOT-23
DBV
DBV
DBV
DBV
DBV
LMC7215QIM5X/NOPB SOT-23
LMC7225IM5
SOT-23
SOT-23
SOT-23
LMC7225IM5/NOPB
LMC7225IM5X/NOPB
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
2-Sep-2015
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
LMC7215IM5
LMC7215IM5/NOPB
LMC7215IM5X
SOT-23
SOT-23
SOT-23
SOT-23
SOIC
DBV
DBV
DBV
DBV
D
5
5
5
5
8
5
5
5
5
5
1000
1000
3000
3000
2500
1000
3000
1000
1000
3000
210.0
210.0
210.0
210.0
367.0
210.0
210.0
210.0
210.0
210.0
185.0
185.0
185.0
185.0
367.0
185.0
185.0
185.0
185.0
185.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
LMC7215IM5X/NOPB
LMC7215IMX/NOPB
LMC7215QIM5/NOPB
LMC7215QIM5X/NOPB
LMC7225IM5
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
DBV
DBV
DBV
DBV
DBV
LMC7225IM5/NOPB
LMC7225IM5X/NOPB
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
相关型号：
LMC7215IM5/NOPB
IC COMPARATOR, 8000 uV OFFSET-MAX, 17000 ns RESPONSE TIME, PDSO5, SOT-23, 5 PIN, Comparator
NSC
LMC7215IM5/NOPB
COMPARATOR, 8000uV OFFSET-MAX, 17000ns RESPONSE TIME, PDSO5, SOT-23, 5 PIN
ROCHESTER
LMC7215IM5X
Micro-Power, Rail-to-Rail CMOS Comparators with Open-Drain/Push-Pull Outputs and TinyPak⑩ Package
NSC
LMC7215IM5X/NOPB
COMPARATOR, 8000uV OFFSET-MAX, 17000ns RESPONSE TIME, PDSO5, LEAD FREE, SOT-23, 5 PIN
ROCHESTER
LMC7215IMX
Micro-Power, Rail-to-Rail CMOS Comparators with Open-Drain/Push-Pull Outputs and TinyPak⑩ Package
NSC
LMC7215IMX/NOPB
IC COMPARATOR, 8000 uV OFFSET-MAX, 17000 ns RESPONSE TIME, PDSO8, SOIC-8, Comparator
NSC
©2020 ICPDF网 联系我们和版权申明