LMH0384 [TI]
3G HD/SD SDI 远距离和可配置自适应电缆均衡器;
| 型号： | LMH0384 |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | 3G HD/SD SDI 远距离和可配置自适应电缆均衡器 |
| 文件： | 总31页 (文件大小：751K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Sample &
Buy
Support &
Community
Product
Folder
Tools &
Software
Technical
Documents
LMH0384
SNLS308G –APRIL 2009–REVISED JUNE 2015
LMH0384 3-Gbps HD - SD SDI Extended Reach and Configurable Adaptive Cable
Equalizer
1 Features
3 Description
The LMH0384 3-Gbps HD - SD SDI Extended Reach
and Configurable Adaptive Cable Equalizer is
designed to equalize data transmitted over cable (or
1
•
Compliant With ST 424, ST 292, ST 344, and ST
259
•
•
Supports DVB-ASI at 270 Mbps
any
media
with
similar
dispersive
loss
Wide Range of Data Rates: 125 Mbps to 2.97
Gbps
characteristics). The equalizer operates over a wide
range of data rates from 125 Mbps to 2.97 Gbps and
supports ST 424, ST 292, ST 344, and ST 259
standards.
•
Equalizes up to 140 Meters of Belden 1694A at
2.97 Gbps, up to 200 Meters of Belden 1694A at
1.485 Gbps, or Up to 400 Meters of Belden 1694A
at 270 Mbps
The LMH0384 device includes active sensing
features and design enhancements including longer
cable equalization, lower output jitter, configurable pin
mode and SPI modes, a power-saving sleep mode,
and programmable output common-mode voltage and
swing. The LMH0384 implements DC restoration to
correctly handle pathological data conditions.
•
Power Save Mode With Auto Sleep Control (35
mW Typical Power Consumption in Power Save
Mode)
•
•
Optional SPI Register Access
Manual Bypass and Output Mute With a
Programmable Threshold
The LMH0384 includes an auto sleep mode to power
down the device when no input signal is detected.
Other features include separate carrier detect and
output mute pins which may be tied together to mute
the output when no input signal is present, and a
programmable mute reference which may be used to
mute the output at a selectable level of signal
degradation.
•
•
Internally Terminated 100-Ω LVDS Outputs With
SPI Programmable Output Common-Mode
Voltage and Swing
Programmable Launch Amplitude Optimization in
SPI Mode
•
•
•
•
•
Cable Length Indicator in SPI Mode
Single 3.3-V Supply Operation
The LMH0384 supports two modes of operation. In
pin mode (non-SPI mode) the LMH0384 is footprint
compatible with the LMH0344 and legacy SDI
equalizers. In the optional SPI mode, the LMH0384
provides register access to all of its features along
with a cable length indicator, programmable output
common-mode voltage and swing, and launch
amplitude optimization.
16-Pin WQFN Package
Industrial Temperature Range: −40°C to +85°C
Footprint Compatible With the LMH0344,
LMH0044, and LMH0074 in Pin Mode
2 Applications
Device Information(1)
•
ST 424, ST 292, ST 344, and ST 259 Serial
Digital Interfaces
PART NUMBER
PACKAGE
BODY SIZE (NOM)
LMH0384
WQFN (16)
4.00 mm × 4.00 mm
•
•
Serial Digital Data Equalization and Reception
(1)
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Data Recovery Equalization
Functional Block Diagram
BYPASS
Output
Driver
DC
SDI
SDI
SDO
SDO
Equalizer
Filter
Restoration/
Level Control
MUTE
Energy
Detect
Energy
Detect
SPI Control
Carrier
Detect
CD
SPI_EN
6
(1) Due to SMPTE naming convention, all SMPTE Engineering
Documents will be numbered as a 2-letter prefix and a
number. Documents and references with the same root
number and year are functionally identical; for example ST
424-2006 and SMPTE 424M-2006 refer to the same
Automatic
Equalization
Control
MUTE
MUTE
REF
REF
AUTO SLEEP
AEC+ AEC-
document.
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LMH0384
SNLS308G –APRIL 2009–REVISED JUNE 2015
www.ti.com
Table of Contents
7.4 Device Functional Modes........................................ 12
7.5 Programming........................................................... 13
7.6 Register Maps......................................................... 16
Application and Implementation ........................ 18
8.1 Application Information............................................ 18
8.2 Typical Application .................................................. 18
8.3 Dos and Don'ts........................................................ 20
Power Supply Recommendations...................... 21
1
2
3
4
5
6
Features.................................................................. 1
Applications ........................................................... 1
Description ............................................................. 1
Revision History..................................................... 2
Pin Configuration and Functions......................... 3
Specifications......................................................... 5
6.1 Absolute Maximum Ratings ...................................... 5
6.2 ESD Ratings.............................................................. 5
6.3 Recommended Operating Conditions....................... 5
6.4 Thermal Information.................................................. 5
6.5 DC Electrical Characteristics .................................... 5
6.6 AC Electrical Characteristics..................................... 6
6.7 Timing Requirements................................................ 7
6.8 Switching Characteristics.......................................... 7
6.9 Typical Characteristics.............................................. 9
Detailed Description ............................................ 10
7.1 Overview ................................................................. 10
7.2 Functional Block Diagram ....................................... 10
7.3 Feature Description................................................. 10
8
9
10 Layout................................................................... 21
10.1 Layout Guidelines ................................................. 21
10.2 Layout Example .................................................... 22
11 Device and Documentation Support ................. 23
11.1 Documentation Support ........................................ 23
11.2 Community Resources.......................................... 23
11.3 Trademarks........................................................... 23
11.4 Electrostatic Discharge Caution............................ 23
11.5 Glossary................................................................ 23
7
12 Mechanical, Packaging, and Orderable
Information ........................................................... 23
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision F (April 2013) to Revision G
Page
•
Added, updated, or renamed the following sections: Device Information Table, Pin Configuration and Functions;
Specifications; Applications and Implementation; Detailed Description; Layout;Device and Documentation Support;
Mechanical, Packaging, and Ordering Information ............................................................................................................... 1
•
•
Added "(logic zero)" to Pin 14 - MUTE - in Pin Descriptions – Pin Mode (non-SPI) / SPI_EN = GND / LMH0344
Compatible table..................................................................................................................................................................... 3
Added note "Typical pullup or pulldown for digital pin is 100 kΩ. The tolerance is between 69K to 131K" to DC
Electrical Characteristics ........................................................................................................................................................ 5
Changes from Revision E (April 2013) to Revision F
Page
•
Changed layout of National Data Sheet to TI format ........................................................................................................... 17
2
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LMH0384
LMH0384
www.ti.com
SNLS308G –APRIL 2009–REVISED JUNE 2015
5 Pin Configuration and Functions
RUM Package
16-Pin WQFN
Top View
16
15
14
13
V
1
2
3
4
12 AUTO SLEEP
EE
SDI
SDO
SDO
11
10
9
LMH0384
SDI
SPI_EN
V
EE
5
6
7
8
DAP = V
EE
NOTE: The exposed die attach pad is a negative electrical terminal for this device. It should be connected to the negative
power supply voltage.
Pin Functions – Pin Mode (non-SPI) / SPI_EN = GND / LMH0344 Compatible
PIN
I/O, TYPE
DESCRIPTION
NO.
1
NAME
VEE
Ground
I, SDI
Negative power supply (ground).
Serial data true input.
2
SDI
3
SDI
I, SDI
Serial data complement input.
4
SPI_EN
I, LVCMOS
SPI register access enable. This pin has an internal pulldown.
H = SPI register access mode.
L = Pin mode.
5
6
7
AEC+
AEC-
I/O, Analog
I/O, Analog
I, LVCMOS
AEC loop filter external capacitor (1-µF) positive connection.
AEC loop filter external capacitor (1-µF) negative connection.
BYPASS
Equalization bypass. This pin has an internal pulldown.
H = Equalization is bypassed (no equalization occurs).
L = Normal operation.
8
MUTEREF
I, Analog
Mute reference input. Sets the threshold for CD and (with CD tied to MUTE) determines the
maximum cable to be equalized before muting. MUTEREF may be either unconnected or
connected to ground for normal CD operation.
9
VEE
SDO
SDO
I, LVCMOS
O, LVDS
Connect this pin to ground or drive it logic low.
Serial data complement output.
Serial data true output.
10
11
12
O, LVDS
AUTO
SLEEP
I, LVCMOS
Auto Sleep. AUTO SLEEP has precedence over MUTE and BYPASS. This pin has an
internal pullup.
H = Device will power down when no input is detected.
L = Normal operation (device will not enter auto power down).
13
14
VCC
Power
Positive power supply (+3.3 V).
MUTE
I, LVCMOS
Output mute. CD may be tied to this pin to inhibit the output when no input signal is present.
MUTE has precedence over BYPASS. This pin has an internal pulldown.
H = Outputs forced to a muted state (logic zero).
L = Outputs enabled.
15
CD
O, LVCMOS Carrier detect.
H = No input signal detected.
L = Input signal detected.
16
—
VCC
VEE
Power
Positive power supply (+3.3 V).
Ground
Connect exposed DAP to negative power supply (ground).
Copyright © 2009–2015, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LMH0384
LMH0384
SNLS308G –APRIL 2009–REVISED JUNE 2015
www.ti.com
RUM Package
16-Pin WQFN
Top View
16
15
14
13
V
EE
MISO
SDO
1
2
3
4
12
11
10
9
SDI
LMH0384
SDO
SS
SDI
SPI_EN
5
6
7
8
DAP = V
EE
NOTE: The exposed die attach pad is a negative electrical terminal for this device. It should be connected to the negative
power supply voltage.
Pin Functions – SPI Mode / SPI_EN = VCC
PIN
I/O, TYPE
DESCRIPTION
NO.
1
NAME
VEE
Ground
I, SDI
Negative power supply (ground).
Serial data true input.
2
SDI
3
SDI
I, SDI
Serial data complement input.
4
SPI_EN
I, LVCMOS
SPI register access enable. This pin has an internal pulldown.
H = SPI register access mode.
L = Pin mode.
5
6
7
AEC+
AEC-
CD
I/O, Analog
I/O, Analog
AEC loop filter external capacitor (1 µF) positive connection.
AEC loop filter external capacitor (1 µF) negative connection.
O, LVCMOS Carrier detect.
H = No input signal detected.
L = Input signal detected.
8
MUTEREF
I, Analog
Mute reference input. Sets the threshold for CD and (with CD tied to MUTE) determines the
maximum cable to be equalized before muting. MUTEREF may be either unconnected or
connected to ground for normal CD operation.
9
SS (SPI)
SDO
I, LVCMOS
O, LVDS
O, LVDS
SPI slave select. This pin has an internal pullup.
Serial data complement output.
Serial data true output.
10
11
12
13
14
15
16
—
SDO
MISO (SPI)
VCC
O, LVCMOS SPI Master Input / Slave Output. LMH0384 data transmit.
Power
I, LVCMOS
I, LVCMOS
Power
Positive power supply (+3.3 V).
SCK (SPI)
MOSI (SPI)
VCC
SPI serial clock input.
SPI Master Output / Slave Input. LMH0384 data receive.
Positive power supply (+3.3 V).
VEE
Ground
Connect exposed DAP to negative power supply (ground).
4
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LMH0384
LMH0384
www.ti.com
SNLS308G –APRIL 2009–REVISED JUNE 2015
6 Specifications
6.1 Absolute Maximum Ratings(1)
MIN
−0.3
−65
MAX
4.0
UNIT
V
Supply voltage
Input voltage (all inputs)
Junction temperature
Storage temperature
VCC+0.3
125
V
°C
°C
150
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
6.2 ESD Ratings
VALUE
±6500
±2000
±400
UNIT
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1)
Charged-device model (CDM), per JEDEC specification JESD22-C101(2)
Machine model (MM)
V(ESD)
Electrostatic discharge
V
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. Manufacturing with
less than 500-V HBM is possible with the necessary precautions. Pins listed as ±6500 V may actually have higher performance.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process. Manufacturing with
less than 250-V CDM is possible with the necessary precautions. Pins listed as ±2000 V may actually have higher performance.
6.3 Recommended Operating Conditions
MIN
NOM
3.3
1
MAX UNIT
VCC – VEE
Supply Voltage
3.135
3.465
V
Input Coupling Capacitance
µF
µF
°C
AEC Capacitor (Connected between AEC+ and AEC-)
Operating Free Air Temperature
1
TA
−40
85
6.4 Thermal Information
LMH0384
THERMAL METRIC(1)
WQFN (RUM)
UNIT
16 PINS
RθJA
Junction-to-ambient thermal resistance
40
6
°C/W
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
6.5 DC Electrical Characteristics
Over Supply Voltage and Operating Temperature ranges, unless otherwise specified.(1)(2)(3)(4)
PARAMETER
TEST CONDITIONS
MIN
2
TYP
MAX
VCC
0.8
UNIT
V
VIH
Input Voltage High Level (Logic Inputs)
Input Voltage Low Level
VIL
VEE
720
V
VSDI
VCMIN
Input Voltage Swing (SDI, SDI)
Input Common-Mode Voltage (SDI, SDI)
0 m cable length(5)
800
950 mVP−P
V
1.75
(1) Current flow into device pins is defined as positive. Current flow out of device pins is defined as negative. All voltages are stated
referenced to VEE = 0 Volts.
(2) Typical values are stated for VCC = +3.3 V and TA = +25°C.
(3) Typical pullup or pulldown for digital pin is 100 kΩ.
(4) Due to SMPTE naming convention, all SMPTE Engineering Documents will be numbered as a two-letter prefix and a number.
Documents and references with the same root number and year are functionally identical; for example ST 424-2006 and SMPTE 424M-
2006l refer to the same document.
(5) The LMH0384 can be optimized for different launch amplitudes through the SPI.
Copyright © 2009–2015, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: LMH0384
LMH0384
SNLS308G –APRIL 2009–REVISED JUNE 2015
www.ti.com
DC Electrical Characteristics (continued)
Over Supply Voltage and Operating Temperature ranges, unless otherwise specified.(1)(2)(3)(4)
PARAMETER
TEST CONDITIONS
MIN
500
250
TYP
700
350
MAX
UNIT
Differential Output Voltage, P-P (SDO,
SDO)
VSSP-P
VOD
900 mVP-P
Differential Output Voltage (SDO, SDO)
450
50
mV
mV
V
Change in Magnitude of VOD for
Complementary Output States (SDO,
SDO)
ΔVOD
VOS
100-Ω load, default values(6)
,
see Figure 1
Offset Voltage (SDO, SDO)
1.125
1.25
1.375
50
Change in Magnitude of VOS for
Complementary Output States (SDO,
SDO)
ΔVOS
IOS
mV
Output Short Circuit Current (SDO, SDO)
30
mA
V
MUTEREF MUTEREF DC Voltage (floating)
MUTEREF Range
1.3
0.8
V
VOH
VOL
Output Voltage High Level (CD, MISO)
Output Voltage Low Level (CD, MISO)
IOH = -2 mA
IOL = +2 mA
2.4
V
0.4
85
V
Normal operation, equalizing cable <
140m (Belden 1694A)(7)
70
mA
ICC
Supply Current
Normal operation, equalizing cable >
140 m (Belden 1694A)
90
10
110
14
mA
mA
Power save mode
(6) The differential output voltage and offset voltage are adjustable through the SPI.
(7) The equalizer automatically shifts equalization stages at cable lengths less than 140 m (Belden 1694A) to reduce power consumption.
This power savings is also achieved by setting Extended 3G Reach Mode = 1 through the SPI.
6.6 AC Electrical Characteristics
Over Supply Voltage and Operating Temperature ranges, unless otherwise specified
(1)
.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Minimum Input Data Rate (SDI,
SDI)
BRMIN
BRMAX
125
Mbps
Maximum Input Data Rate (SDI,
SDI)
2970
0.2
Mbps
270 Mbps, Belden 1694A,
0 to 350 meters(2)
270 Mbps, Belden 1694A,
350 to 400 meters
0.2
0.3
1.485 Gbps, Belden 1694A,
0 to 170 meters(2)
0.25
0.3
TJRAW
Jitter for Various Cable Lengths
UI
1.485 Gbps, Belden 1694A,
170 to 200 meters
2.97 Gbps, Belden 1694A,
0-110 meters(2)
2.97 Gbps, Belden 1694A,
110 to 140 meters
20% to 80%, 100-Ω load(3)
,
0.35
80
Output Rise Time, Fall Time
(SDO, SDO)
tr,tf
130
ps
ps
see Figure 1
Mismatch in Rise/Fall Time (SDO,
SDO)
(3)
See
2
15
(3)
tOS
Output Overshoot (SDO, SDO)
See
1%
5%
(1) Typical values are stated for VCC = +3.3 V and TA = +25°C.
(2) Based on design and characterization data over the full range of recommended operating conditions of the device. Jitter is measured in
accordance with ST RP 184, ST RP 192, and the applicable serial data transmission standard: ST 424, ST 292, or ST 259.
(3) Specification is ensured by characterization.
6
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LMH0384
LMH0384
www.ti.com
SNLS308G –APRIL 2009–REVISED JUNE 2015
AC Electrical Characteristics (continued)
(1)
Over Supply Voltage and Operating Temperature ranges, unless otherwise specified
.
PARAMETER
TEST CONDITIONS
5 MHz to 1.5 GHz(4)
1.5 GHz to 3.0 GHz(4)
MIN
TYP
MAX
UNIT
dB
15
10
RLIN
Input Return Loss (SDI, SDI)
dB
RIN
CIN
Input Resistance (SDI, SDI)
Input Capacitance (SDI, SDI)
single-ended
1.3
0.7
kΩ
single-ended
pF
(4) Input return loss is dependent onboard design. The LMH0384 exceeds this specification on the SD384 evaluation board with a return
loss network consisting of a 5.6 nH inductor in parallel with the 75-Ω series resistor on the input.
6.7 Timing Requirements
over operating free-air temperature range (unless otherwise noted)
MIN
TYP
MAX
UNIT
fSCK
tPH
SCK Frequency
20
MHz
% SCK
period
SCK Pulse Width High
40
40
See Figure 2 and Figure 3
% SCK
period
tPL
SCK Pulse Width Low
tSU
MOSI Setup Time
MOSI Hold Time
SS Setup Time
SS Hold Time
SS Off Time
4
4
ns
ns
ns
ns
ns
See Figure 2 and Figure 3
See Figure 2 and Figure 3
tH
tSSSU
tSSH
tSSOF
4
4
10
6.8 Switching Characteristics
over operating free-air temperature range (unless otherwise noted)
MIN
TYP
MAX
15
UNIT
ns
tODZ
tOZD
tOD
MISO Driven-to-Tristate Time
MISO Tristate-to-Driven Time
MISO Output Delay Time
See Figure 3
15
ns
15
ns
VOD
-
VOS
VOD
+
80%
80%
+ VOD
VSSP-P
0V differential
- VOD
20%
20%
VSSP-P = (VOD+) – (VOD-)
tr
tf
Figure 1. LVDS Output Voltage, Offset, and Timing Parameters
Copyright © 2009–2015, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: LMH0384
LMH0384
SNLS308G –APRIL 2009–REVISED JUNE 2015
www.ti.com
SS
(host)
t
t
t
PL
SSSU
PH
tSSH tSSOF
SCK
(host)
t
H
t
SU
MOSI
(host)
0
A6
A5
A4
A3
A2
A1
A0
D7
D6
D5
D4
D3
D2
D1
D0
Hi-Z
MISO
(device)
Figure 2. SPI Write
SS
(host)
t
t
t
PL
SSSU
PH
t
SSH
t
SSOF
SCK
(host)
t
H
t
SU
MOSI
(host)
Hi-Z
1
A6
A5
A4
A3
A2
A1
A0
t
t
OZD
OD
t
ODZ
Hi-Z
Hi-Z
MISO
(device)
D7
D6
D5
D4
D3
D2
D1
D0
Figure 3. SPI Read
8
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LMH0384
LMH0384
www.ti.com
SNLS308G –APRIL 2009–REVISED JUNE 2015
6.9 Typical Characteristics
Typical device characteristics at TA = +25°C and VDD = 3.3 V, unless otherwise noted.
Time: 50 ps/div
Figure 5. 100-M B1694A PRBS10 2.97 Gbps
Time: 50 ps/div
Figure 4. 20-M B1694A PRBS10 2.97 Gbps
Copyright © 2009–2015, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: LMH0384
LMH0384
SNLS308G –APRIL 2009–REVISED JUNE 2015
www.ti.com
7 Detailed Description
7.1 Overview
The LMH0384 3-Gbps HD - SD SDI Extended Reach and Configurable Adaptive Cable Equalizer is designed to
equalize data transmitted over cable (or any media with similar dispersive loss characteristics). The equalizer
operates over a wide range of data rates from 125 Mbps to 2.97 Gbps and supports ST 424, ST 292, ST 344,
and ST 259 standards. The LMH0384 includes active sensing features and design enhancements including
longer cable equalization, lower output jitter, configurable pin mode and SPI modes, a power-saving sleep mode,
and programmable output common-mode voltage and swing. The LMH0384 implements DC restoration to
correctly handle pathological data conditions.
7.2 Functional Block Diagram
BYPASS
Output
Driver
DC
SDI
SDI
SDO
SDO
Equalizer
Filter
Restoration/
Level Control
MUTE
Energy
Detect
Energy
Detect
SPI Control
Carrier
Detect
CD
SPI_EN
6
Automatic
Equalization
Control
MUTE
MUTE
REF
REF
AUTO SLEEP
AEC+ AEC-
Figure 6. Pin Mode
7.3 Feature Description
7.3.1 Block Description
The Equalizer Filter block is a multistage adaptive filter. If BYPASS is high, the equalizer filter is disabled.
The DC Restoration / Level Control block receives the differential signals from the equalizer filter block. This
block incorporates a self-biasing DC restoration circuit to fully DC restore the signals. If BYPASS is high, this
function is disabled.
The signals before and after the DC Restoration / Level Control block are used to generate the Automatic
Equalization Control (AEC) signal. This control signal sets the gain and bandwidth of the equalizer filter. The
loop response in the AEC block is controlled by an external 1-µF capacitor placed across the AEC+ and AEC-
pins.
The Carrier Detect block generates the carrier detect signal based on the SDI input and an adjustment from the
Mute Reference block.
10
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LMH0384
LMH0384
www.ti.com
SNLS308G –APRIL 2009–REVISED JUNE 2015
Feature Description (continued)
The SPI Control block uses the MOSI, MISO, SCK, and SS signals in SPI mode to control the SPI registers.
SPI_EN selects between SPI mode and pin mode. In pin mode, SPI_EN is driven logic low.
The Output Driver produces SDO and SDO.
7.3.2 Mute Reference (MUTEREF
)
The mute reference sets the threshold for CD and (with CD tied to MUTE) determines the amount of cable to
equalize before automatically muting the outputs. This is set by applying a voltage inversely proportional to the
length of cable to equalize. The applied voltage must be greater than the MUTEREF floating voltage (typically 1.3
V) in order to change the CD threshold. As the applied MUTEREF voltage is increased, the amount of cable that
can be equalized before carrier detect is deasserted and the outputs are muted is decreased. MUTEREF may be
left unconnected or connected to ground for normal CD operation.
7.3.3 Carrier Detect (CD) and Mute
Carrier detect CD indicates if a valid signal is present at the LMH0384 input. If MUTEREF is used, the carrier
detect threshold will be altered accordingly. CD provides a high voltage when no signal is present at the
LMH0384 input. CD is low when a valid input signal is detected.
MUTE can be used to manually mute or enable SDO and SDO. Applying a high input to MUTE will mute the
LMH0384 outputs by forcing the output to a logic zero. Applying a low input will force the outputs to be active.
CD and MUTE may be tied together to automatically mute the output when no input signal is present.
7.3.4 Auto Sleep
The auto sleep mode allows the LMH0384 to power down when no input signal is detected. If the AUTO SLEEP
pin is set high, the LMH0384 goes into a deep power save mode when no signal is detected. The device powers
on again once an input signal is detected. The auto sleep functionality can be turned off by setting AUTO SLEEP
low or tying this pin to ground. An additional auto sleep setting available in SPI mode can be used to force the
equalizer to power down regardless of whether there is an input signal or not. Auto sleep has precedence over
mute and bypass modes.
In auto sleep mode, the time to power down the equalizer when the input signal is removed is less than 200 µs
and should not have any impact on the system timing requirements. The device will wake up automatically once
an input signal is detected (within 1 μs). The overall system will be limited only by the settling time constant of
the equalizer adaptation loop.
7.3.5 Input Interfacing
The LMH0384 accepts either differential or single-ended input. The input must be AC-coupled. Functional Block
Diagram shows the typical configuration for a single-ended input. The unused input must be properly terminated
as shown.
The LMH0384 can be optimized for different launch amplitudes through the SPI (see Launch Amplitude
Optimization in Programming).
The LMH0384 correctly handles equalizer pathological signals for standard definition and high definition serial
digital video, as described in SMPTE RP 178 and RP 198, respectively.
7.3.6 Output Interfacing
SDO and SDO together are internally terminated 100-Ω LVDS outputs. These outputs can be DC coupled to
most common differential receivers.
The default output common-mode voltage (VOS) is 1.25 V. The output common-mode voltage may be adjusted
through the SPI in 200-mV increments, from 1.05 V to 1.85 V (see Output Driver Adjustments in Programming).
This adjustable output common-mode voltage offers flexibility for interfacing to many types of receivers.
The default differential output swing (VSSP-P) is 700 mVP-P. The differential output swing may be adjusted through
the SPI in 100 mV increments from 400 mVP-P to 800 mVP-P (see Output Driver Adjustments in Programming).
Copyright © 2009–2015, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: LMH0384
LMH0384
SNLS308G –APRIL 2009–REVISED JUNE 2015
www.ti.com
Feature Description (continued)
The LMH0384 output should be DC coupled to the input of the receiving device as long as the common-mode
ranges of both devices are compatible. 100-Ω differential transmission lines should be used to connect between
the LMH0384 outputs and the input of the receiving device where possible. Figure 7 shows an example of a DC-
coupled interface between the LMH0384 and LMH0346 SDI reclocker. All that is required is the 100-Ω differential
termination as shown. The resistor should be placed as close as possible to the LMH0346 input. If desired, this
network may be terminated with two 50-Ω resistors and a center tap capacitor to ground in place of the signal
100-Ω resistor.
Figure 8 shows an example of a DC-coupled interface between the LMH0384 and LMH0356 SDI reclocker. The
LMH0356 inputs have 50-Ω internal terminations (100-Ω differential) to terminate the transmission line, so no
additional components are required.
The LMH0384 allows flexibility when interfacing to low voltage crosspoint switches (that is, 1.8 V) and other
devices with limited input ranges. The LMH0384 outputs can be DC coupled to these devices in most cases,
avoiding the need to AC couple.
The LMH0384 may be AC-coupled to the receiving device when necessary. For example, the LMH0384 outputs
are not strictly compatible with 3.3 V CML and thus should not be connected through 50-Ω resistors to 3.3 V. If
the input common-mode range of the receiving device is not compatible with the output common-mode range of
the LMH0384, then AC coupling is required. Following the AC-coupling capacitors, the signal may have to be
biased at the input of the receiving device.
Coaxial Cable
1.0 PF
75:
SDI
SDI
SDI
SDO
SDO
LMH0346
3G/HD/SD
SDI Reclocker
LMH0384
100:
100: Differential T-Line
1.0 PF
5.6 nH
SDI
75:ꢀ
37.4:
Figure 7. DC Output Interface to LMH0346 Reclocker
Coaxial Cable
1.0 PF
75:
SDI
SDO
SDO
SDI0
SDI0
LMH0356
3G/HD/SD
SDI Reclocker
LMH0384
100: Differential T-Line
1.0 PF
5.6 nH
SDI
75:ꢀ
37.4:
Figure 8. DC Output Interface to LMH0356 Reclocker
7.4 Device Functional Modes
The LMH0384 supports two modes of operation: Pin and SPI Mode. In pin mode the LMH0384 is footprint
compatible with the LMH0344 and legacy SDI equalizers. In the optional SPI mode, the LMH0384 provides
register access to all of its features along with a cable length indicator, programmable output common-mode
voltage and swing, and launch amplitude optimization.
12
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LMH0384
LMH0384
www.ti.com
SNLS308G –APRIL 2009–REVISED JUNE 2015
7.5 Programming
Setting SPI_EN high enables the optional SPI register access mode. In SPI mode, the LMH0384 provides
register access to all of its features along with a cable length indicator, programmable output common-mode
voltage and swing, and launch amplitude optimization. There are five supported 8-bit registers in the device (see
Table 1). With SPI_EN set low, the device operates in pin mode and is footprint compatible with the LMH0344,
LMH0044, and LMH0074.
7.5.1 SPI Write
The SPI write is shown in Figure 2. The MOSI payload consists of a “0” (write command), seven address bits,
and eight data bits. The SS signal is driven low, and the 16 bits are sent to the LMH0384's MOSI input. Data is
latched on the rising edge of SCK. The MISO output is normally tri-stated during this operation. After the SPI
write, SS must return high.
7.5.2 SPI Read
The SPI read is shown in Figure 3. The MOSI payload consists of a “1” (read command) and seven address bits.
The SS signal is driven low, and the eight bits are sent to the LMH0384's MOSI input. The addressed location is
accessed immediately after the rising edge of the 8th clock and the eight data bits are shifted out on MISO
starting with the falling edge of the 8th clock. MOSI must be tri-stated immediately after the rising edge of the 8th
clock. After the SPI read, SS must return high.
7.5.3 Output Driver Adjustments
The output driver swing (amplitude) and offset voltage (common-mode voltage) are adjustable through SPI
register 01h.
The output swing is adjustable through bits [7:5] of SPI register 01h. The default value for these register bits is
“011” for a peak to peak differential output voltage of 700 mVP-P. The output swing can be adjusted in 100 mV
increments from 400 mVP-P to 800 mVP-P
.
The offset voltage is adjustable through bits [4:2] of SPI register 01h. The default value for these register bits is
“001” for an output offset of 1.25 V. The output common-mode voltage may be adjusted in 200-mV increments,
from 1.05 V to 1.85 V. It can also be set to “101” for the maximum offset voltage. At this maximum offset voltage
setting, the outputs are referenced to the positive supply and the offset voltage is around 2.1 V.
7.5.4 Launch Amplitude Optimization
The LMH0384 can compensate for attenuation of the input signal prior to the equalizer. This compensation is
useful for applications with a passive splitter at the equalizer input or a non-ideal input termination network, and
is controlled by SPI register 02h.
Bit 7 of SPI register 02h is used for coarse control of the launch amplitude setting. At the default setting of “0”,
the LMH0384 operates normally and expects a launch amplitude of 800 mVP-P. Bit 7 may be set to “1” to optimize
the LMH0384 for input signals with 6 dB of attenuation (400 mVP-P).
Once the coarse control is set, the LMH0384 input compensation may be further fine tuned by bits [6:3] of SPI
register 02h. These bits may be used to tweak the input gain stage -22% to +40% around the coarse control
setting.
Copyright © 2009–2015, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: LMH0384
LMH0384
SNLS308G –APRIL 2009–REVISED JUNE 2015
www.ti.com
Programming (continued)
7.5.5 Cable Length Indicator (CLI)
The Cable Length Indicator (CLI) provides an indication of the length of cable attached to the input. CLI is
accessible through bits [7:3] of SPI register 03h. The 5-bit CLI ranges in decimal value from 0 to 25 (“00000” to
“11001” binary) and increases as the cable length is increased. Figure 9 shows typical CLI values vs. Belden
1694A cable length. CLI is valid for Belden 1694A cable lengths of up to 140 m at 2.97 Gbps, 200 m at 1.485
Gbps, and 400 m at 270 Mbps.
30
25
20
15
10
5
0
0
50 100 150 200 250 300 350 400
BELDEN 1694A CABLE LENGTH (m)
Figure 9. CLI vs. Belden 1694A Cable Length
7.5.6 Application of CLI: Extending 3G Reach
An application of CLI is to extend the 3G reach in systems which have margin in the jitter budget. This allows for
additional cable reach at 2.97 Gbps at the expense of slightly higher output jitter. The extended 3G reach mode
provides 15m of additional Belden 1694A cable reach, with an increase of output jitter at this longer cable length
of 0.05 to 0.1 UI.
The extended 3G reach mode is accessible through bit 2 of SPI register 00h. In order to achieve longer 3G cable
reach while still maintaining the performance at HD and SD data rates, a state machine can be implemented as
shown in Figure 10. (Note: If this procedure is not followed, the maximum equalizable cable lengths for HD and
SD data rates will be limited to less than what can be achieved in normal mode).
14
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LMH0384
LMH0384
www.ti.com
SNLS308G –APRIL 2009–REVISED JUNE 2015
Programming (continued)
(CD = 0) || (CLI > 180m)
(Reg 00h, bit 7 = 0) || (Reg 03h, bits [7:3] > 10010)
Normal Mode
(CD = 1) && (CLI < 180m)
(Reg 00h, bit 7 = 1) && (Reg 03h, bits [7:3] < 10010)
Extended 3G Reach Æ Normal
Normal Æ Extended 3G Reach
Register Processing:
Register Processing:
1. Force EQ to Sleep: Reg 00h, bits [4:3] = 10
2. Force Extended 3G Reach Mode OFF: Reg 00h, bit 2 = 0
3. Wait > 1 ms
1. Force EQ to Sleep: Reg 00h, bits [4:3] = 10
2. Force Extended 3G Reach Mode ON: Reg 00h, bit 2 = 1
3. Wait > 1 ms
4. Set Sleep Mode to Auto: Reg 00h, bits [4:3] = 01
4. Set Sleep Mode to Auto: Reg 00h, bits [4:3] = 01
CD = 0
(Reg 00h, bit 7 = 0)
Extended 3G
Reach Mode
Figure 10. Extended 3G Reach Mode State Machine Example
7.5.7 Explanation of Extended 3G Reach Mode State Machine (Figure 10)
When the LMH0384 is powered on, it will be in normal mode. If there is no input signal (register 00h, bit 7 = 0) or
if the input cable is longer than a user programmable cable length (that is 180m, which means register 03h, bits
[7:3] > 10010), then the device should remain in normal mode.
Once an input signal is detected (register 00h, bit 7 = 1) AND the detected cable length is shorter than the user
programmed cable length of 180m (register 03h, bits [7:3] < 10010), then the equalizer can enter the extended
3G reach mode to allow for longer cable lengths at 2.97 Gbps. This requires the following procedure:
1. Force the equalizer to sleep by writing “10” to bits [4:3] of register 00h.
2. Turn on the extended 3G reach mode by writing “1” to bit 2 of register 00h.
3. Wait at least 1ms.
4. Set the sleep mode to auto by writing “01” to bits [4:3] of register 00h. Alternately, sleep mode may be set to
off by writing “00” to bits [4:3] of register 00h.
The equalizer remains in extended 3G reach mode until the cable length is changed. If the cable length is
changed, the input signal drops out momentarily. Once this happens (register 00h, bit 7 = 0), then the following
procedure must be used to set the device back to normal mode:
1. Force the equalizer to sleep by writing “10” to bits [4:3] of register 00h.
2. Turn off the extended 3G reach mode by writing “0” to bit 2 of register 00h.
3. Wait at least 1ms.
4. Set the sleep mode to auto by writing “01” to bits [4:3] of register 00h. Alternately, sleep mode may be set to
off by writing “00” to bits [4:3] of register 00h.
Copyright © 2009–2015, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: LMH0384
LMH0384
SNLS308G –APRIL 2009–REVISED JUNE 2015
www.ti.com
7.6 Register Maps
Table 1. SPI Registers
ADDRESS
R/W
NAME
BITS
FIELD
DEFAULT
DESCRIPTION
0: No carrier detected.
1: Carrier detected.
7
6
5
Carrier Detect
Mute has precedence over
Bypass.
0: Normal operation.
1: Outputs muted.
Mute
0
0
0: Normal operation.
1: Equalizer bypassed.
Bypass
Sleep mode control. Sleep has
precedence over Mute and
Bypass.
00: Disable sleep mode (force
equalizer to stay enabled).
01: Sleep mode active when no
input signal detected.
00h
R/W
General Control
4:3
Sleep Mode
01
10: Force equalizer into sleep
mode (powered down)
regardless of whether there is
an input signal or not.
11: Reserved.
Extended 3G reach mode to
extend the cable length for 2.97
Gbps applications.
0: Normal operation.
1: Extended 3G reach mode.
2
Extended 3G Reach Mode
Reserved
0
Reserved as 00. Always write
00 to these bits.
1:0
00
Output driver swing (VSSP-P).
000: VSSP-P = 400 mVP-P
001: VSSP-P = 500 mVP-P
010: VSSP-P = 600 mVP-P
011: VSSP-P = 700 mVP-P
100: VSSP-P = 800 mVP-P
.
.
.
.
.
7:5
Output Swing
011
101, 110, 111: Reserved.
Output driver offset voltage
(common-mode voltage).
000: VOS = 1.05V.
01h
R/W
Output Driver
001: VOS = 1.25V.
010: VOS = 1.45V.
011: VOS = 1.65V.
100: VOS = 1.85V.
101: VOS referenced to positive
supply.
4:2
1:0
Offset Voltage
Reserved
001
00
110, 111: Reserved.
Reserved as 00. Always write
00 to these bits.
16
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LMH0384
LMH0384
www.ti.com
SNLS308G –APRIL 2009–REVISED JUNE 2015
Register Maps (continued)
Table 1. SPI Registers (continued)
ADDRESS
R/W
NAME
BITS
FIELD
DEFAULT
DESCRIPTION
Coarse launch amplitude
optimization.
0: Normal optimization with no
external attenuation (800 mVP-P
launch amplitude).
7
Coarse Control
0
1: Optimized for 6 dB external
attenuation (400 mVP-P launch
amplitude).
Launch amplitude optimization
fine tuning.
0000: Nominal.
0001: -4% from nominal.
0010: -8% from nominal.
0011: -11% from nominal.
0100: -14% from nominal.
0101: -17% from nominal.
0110: -20% from nominal.
0111: -22% from nominal.
1000: Nominal.
02h
R/W
Launch Amplitude
6:3
Fine Control
0000
1001: +4% from nominal.
1010: +9% from nominal.
1011: +14% from nominal.
1100: +20% from nominal.
1101: +26% from nominal.
1110: +33% from nominal.
1111: +40% from nominal.
Reserved as 000. Always write
000 to these bits.
2:0
7:3
Reserved
CLI
000
Cable Length Indicator.
Provides an indication of the
length of cable attached to the
input. CLI increases as the
cable length increases.
03h
04h
R
R
CLI
2:0
7:0
Reserved
000
Reserved.
Device ID
Die Revision
00000010
Die revision.
Copyright © 2009–2015, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links: LMH0384
LMH0384
SNLS308G –APRIL 2009–REVISED JUNE 2015
www.ti.com
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The LMH0384 is a single-channel, 3-Gbps HD - SD SDI Adaptive Cable Equalizer designed to equalize data
transmitted over cable or any media with similar dispersive loss characteristics. The equalizer operates over a
wide range of data rates from 125 Mbps to 2.97 Gbps and supports ST 424, ST 292, ST 344, and ST 259.
Additional features include separate carrier detect and output mute pins which may be tied together to mute the
output when no signal is present. A programmable mute reference is provided to mute the output at a selectable
level of signal degradation. The bypass pin allows the adaptive equalizer to be bypassed. The LMH0384 accepts
either a differential or single-ended input. The input must be AC-coupled.
The LMH0384 correctly handles equalizer pathological signals for standard definition and high definition serial
digital video, as described in ST RP 178 and RP 198, respectively.
8.1.1 Replacing the LMH0344
In pin mode, the LMH0384 is a drop-in replacement for the LMH0344SQ SDI cable equalizer. When replacing an
LMH0344 with an LMH0384, it is important to consider the following points:
1. The LMH0384 auto sleep function is mapped to pin 12 which is a ground pin on the LMH0344SQ. When this
pin is grounded on the LMH0384, the auto sleep function is disabled. To enable auto sleep mode on the
LMH0384, pin 12 must be pulled high.
2. Pin 4 and pin 9 on the LMH0344SQ are true ground pins. For the LMH0384, pin 4 and pin 9 may be driven
logic low in pin mode (they do not require a true ground connection).
3. The LMH0384 has lower input capacitance than the LMH0344 which allows for improved input return loss.
The input return loss network may need to be modified. In most cases, the LMH0384 should provide superior
input return loss.
4. The LMH0384 default output common-mode voltage is different than that of the LMH0344. In most cases,
this should not cause an issue. The LMH0384 and LMH0344 outputs can both be DC coupled to TI's SDI
reclockers and cable drivers. In addition, the LMH0384 output can be DC coupled to LVDS and other inputs
that require lower input common-mode voltages than the LMH0344. The LMH0384 output common-mode
voltage is adjustable through the SPI.
8.2 Typical Application
Figure 11 and Figure 12 show the application circuit for the LMH0384 in SPI mode and Pin mode.
18
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LMH0384
LMH0384
www.ti.com
SNLS308G –APRIL 2009–REVISED JUNE 2015
Typical Application (continued)
(SPI) MISO
(SPI) SCK
(SPI) MOSI
V
CC
V
CC
0.1 PF
0.1 PF
1
2
3
4
12
11
10
9
V
MISO
SDO
SDO
SS
EE
Coaxial Cable
75:
1.0 PF
SDI
Differential
Output
LMH0384
SDI
5.6 nH
75:ꢀꢀ
1.0 PF
SPI_EN
V
CC
37.4:
DAP
1.0 PF
CD
MUTE
REF
(SPI) SS
Figure 11. Application Circuit (SPI Mode)
LMH0384 3G SDI
Adaptive Cable
Equalizer
LMH0341 3G SDI
Deserializer
Coaxial Cable
75:
1.0 PF
SDO
SDO
TXOUT
TXOUT
SDI
SDI
RXIN0
RXIN0
Reclocked
Loopthrough
5.6 nH
1.0 PF
MUTE
MUTE
RX[4:0]
RXCLK
To FPGA
75:ꢀꢀ
REF
37.4:
CD
BYPASS
5-bit LVDS
+ clk
AUTO SLEEP
SPI_EN
MUTE
MUTE
REF
CD
BYPASS
AUTO SLEEP
1.0 PF
Figure 12. Typical Application (Pin Mode)
8.2.1 Design Requirements
Table 2 lists the design parameters for the LMH0384.
Table 2. LMH0384 Design Parameters
DESIGN PARAMETER
REQUIREMENT
Required. A common type of AC-coupling capacitor is 1 µF ±10% X7R ceramic
capacitor (0402 or 0201 size). Capacitors may be implemented on the PCB or in the
connector.
Input AC-coupling capacitors
Copyright © 2009–2015, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Links: LMH0384
LMH0384
SNLS308G –APRIL 2009–REVISED JUNE 2015
www.ti.com
Typical Application (continued)
Table 2. LMH0384 Design Parameters (continued)
DESIGN PARAMETER
REQUIREMENT
The user should check input common mode voltage. If AC coupling capacitor is
required, SDO AC-coupling capacitor is expected to be 4.7 µF ±10%.
Output AC-coupling capacitors
Distance from Device to BNC
Input launch amplitude
Keep this distance as short as possible to minimize parasitic
Refer to DC Electrical Characteristics
8.2.2 Detailed Design Procedure
1. Maximum power draw for PCB regulator selection. For this use maximum power consumption in the data
sheet.
2. Closely compare schematic against typical connection diagram in the data sheet.
3. Plan out the PCB layout and component placement to minimize parasitic.
4. Consult the BNC vendor for optimum BNC landing pattern.
8.2.3 Application Curves
Figure 13 and Figure 14 depict the differential output eye diagrams for SDO, SDO at 2.97 Gbps. Measurements
were done at default operating conditions.
Time: 50 ps/div
Figure 13. 1-M B1694A PRBS10 2.97 Gbps
Time: 50 ps/div
Figure 14. 100-M B1694A PRBS10 2.97 Gbps
8.3 Dos and Don'ts
Pay special attention to the PCB layout for the high speed signals. The SMPTE specifies the requirements for
the Serial Digital Interface to transport digital video at SD, HD, and 3 Gbps data rates over coaxial cables. One of
the requirements is meeting the required Return Loss. This requirement specifies how closely the port resembles
75-Ω impedance across a specified frequency band. The SMPTE specifications also defines the use of AC-
coupling capacitors for transporting uncompressed serial data streams with heavy low frequency content. This
specification requires the use of a 1-µF AC-coupling capacitors on the input of the LMH0384 to avoid low
frequency DC wander.
20
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LMH0384
LMH0384
www.ti.com
SNLS308G –APRIL 2009–REVISED JUNE 2015
9 Power Supply Recommendations
Follow these general guidelines when designing the power supply:
1. The power supply should be designed to provide the recommended operating conditions in terms of DC
voltage, and maximum current consumption.
2. The maximum current draw for the LMH0384 is provided in the data sheet. This figure can be used to
calculate the maximum current the supply must provide. Current consumption can be derived from the typical
power consumption specification in the data sheet.
3. The LMH0384 does not require any special power supply filtering, provided the recommended operating
conditions are met. Only standard supply decoupling is required.
10 Layout
10.1 Layout Guidelines
For information on layout and soldering of the WQFN package, please refer to the following application note: AN-
1187 Leadless Leadframe Package (LLP) (SNOA401).
The ST 424, 292, and 259 standards have stringent requirements for the input return loss of receivers, which
essentially specify how closely the input must resemble a 75-Ω network. Any non-idealities in the network
between the BNC and the equalizer will degrade the input return loss. Take care to minimize impedance
discontinuities between the BNC and the equalizer to ensure that the characteristic impedance of this trace is 75
Ω.
Please consider the following PCB recommendations:
•
Use surface-mount components, and use the smallest components available. In addition, use the smallest
size component pads.
•
•
Select trace widths that minimize the impedance mismatch between the BNC and the equalizer.
Select a board stack up that supports both 75-Ω single-ended traces and 100-Ω loosely-coupled differential
traces.
•
•
•
•
•
Place return loss components closest to the equalizer input pins.
Maintain symmetry on the complementary signals.
Route 100-Ω traces uniformly (keep trace widths and trace spacing uniform along the trace).
Avoid sharp bends in the signal path; use 45° or radial bends.
Place bypass capacitors close to each power pin, and use the shortest path to connect equalizer power and
ground pins to the respective power or ground planes.
Copyright © 2009–2015, Texas Instruments Incorporated
Submit Documentation Feedback
21
Product Folder Links: LMH0384
LMH0384
SNLS308G –APRIL 2009–REVISED JUNE 2015
www.ti.com
10.2 Layout Example
Figure 15 and Figure 16 demonstrate the LMH0384EVM PCB layout. Ground and supply relief under the return
loss passive components and pads reduces parasitic - improving return loss performance. Note 5 vias without
solder paste are located between 4 squares solder paste mainly for thermal as well as to improve soldering
during board assembly.
Figure 15. LMH0384EVM Top Etch Layout Example
Figure 16. LMH384EVM Top Solder Paste Mask
22
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: LMH0384
LMH0384
www.ti.com
SNLS308G –APRIL 2009–REVISED JUNE 2015
11 Device and Documentation Support
11.1 Documentation Support
11.1.1 Related Documentation
For additional information, see the following:
Application Note AN- 1187, Leadless Leadframe Package (LLP) (SNOA401).
11.2 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.3 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.4 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.5 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2009–2015, Texas Instruments Incorporated
Submit Documentation Feedback
23
Product Folder Links: LMH0384
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
LMH0384SQ/NOPB
LMH0384SQE/NOPB
LMH0384SQX/NOPB
ACTIVE
ACTIVE
ACTIVE
WQFN
WQFN
WQFN
RUM
RUM
RUM
16
16
16
1000 RoHS & Green
250 RoHS & Green
4500 RoHS & Green
SN
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
-40 to 85
-40 to 85
-40 to 85
L0384
L0384
L0384
SN
SN
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Aug-2022
TAPE AND REEL INFORMATION
REEL DIMENSIONS
TAPE DIMENSIONS
K0
P1
W
B0
Reel
Diameter
Cavity
A0
A0 Dimension designed to accommodate the component width
B0 Dimension designed to accommodate the component length
K0 Dimension designed to accommodate the component thickness
Overall width of the carrier tape
W
P1 Pitch between successive cavity centers
Reel Width (W1)
QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE
Sprocket Holes
Q1 Q2
Q3 Q4
Q1 Q2
Q3 Q4
User Direction of Feed
Pocket Quadrants
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LMH0384SQ/NOPB
LMH0384SQE/NOPB
LMH0384SQX/NOPB
WQFN
WQFN
WQFN
RUM
RUM
RUM
16
16
16
1000
250
178.0
178.0
330.0
12.4
12.4
12.4
4.3
4.3
4.3
4.3
4.3
4.3
1.3
1.3
1.3
8.0
8.0
8.0
12.0
12.0
12.0
Q1
Q1
Q1
4500
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Aug-2022
TAPE AND REEL BOX DIMENSIONS
Width (mm)
H
W
L
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
LMH0384SQ/NOPB
LMH0384SQE/NOPB
LMH0384SQX/NOPB
WQFN
WQFN
WQFN
RUM
RUM
RUM
16
16
16
1000
250
208.0
208.0
356.0
191.0
191.0
356.0
35.0
35.0
35.0
4500
Pack Materials-Page 2
PACKAGE OUTLINE
RUM0016A
WQFN - 0.8 mm max height
S
C
A
L
E
3
.
0
0
0
PLASTIC QUAD FLATPACK - NO LEAD
4.1
3.9
A
B
PIN 1 INDEX AREA
4.1
3.9
0.8
0.7
C
SEATING PLANE
0.05
0.00
0.08 C
DIM A
OPT 1
0.2
OPT 2
0.1
2X 1.95
SYMM
(DIM A) TYP
5
8
EXPOSED
THERMAL PAD
4
9
2X 1.95
SYMM
17
2.6 0.1
12X 0.65
1
12
0.35
0.25
16X
PIN 1 ID
(45 X 0.3)
13
16
0.1
C A B
0.5
0.3
0.05
16X
4214998/A 11/2021
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. The package thermal pad must be soldered to the printed circuit board for thermal and mechanical performance.
www.ti.com
EXAMPLE BOARD LAYOUT
RUM0016A
WQFN - 0.8 mm max height
PLASTIC QUAD FLATPACK - NO LEAD
(
2.6)
SYMM
SEE SOLDER MASK
DETAIL
13
16
16X (0.6)
1
12
16X (0.3)
17
SYMM
12X (0.65)
(3.8)
(1.05)
4
9
(R0.05) TYP
(
0.2) TYP
VIA
5
8
(1.05)
(3.8)
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE: 20X
0.07 MIN
ALL AROUND
0.07 MAX
ALL AROUND
METAL UNDER
SOLDER MASK
METAL EDGE
EXPOSED METAL
SOLDER MASK
OPENING
EXPOSED
METAL
SOLDER MASK
OPENING
NON SOLDER MASK
SOLDER MASK DEFINED
DEFINED
(PREFERRED)
SOLDER MASK DETAILS
4214998/A 11/2021
NOTES: (continued)
4. This package is designed to be soldered to a thermal pad on the board. For more information, see Texas Instruments literature
number SLUA271 (www.ti.com/lit/slua271).
5. Vias are optional depending on application, refer to device data sheet. If any vias are implemented, refer to their locations shown
on this view. It is recommended that vias under paste be filled, plugged or tented.
www.ti.com
EXAMPLE STENCIL DESIGN
RUM0016A
WQFN - 0.8 mm max height
PLASTIC QUAD FLATPACK - NO LEAD
(0.675) TYP
13
16
16X (0.6)
1
12
16X (0.3)
(0.675) TYP
(3.8)
17
SYMM
12X (0.65)
4X ( 1.15)
9
4
(R0.05) TYP
8
5
SYMM
(3.8)
SOLDER PASTE EXAMPLE
BASED ON 0.125 MM THICK STENCIL
SCALE: 20X
EXPOSED PAD 17
78% PRINTED SOLDER COVERAGE BY AREA UNDER PACKAGE
4214998/A 11/2021
NOTES: (continued)
6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2022, Texas Instruments Incorporated
相关型号：
LMH0387SL/NOPB
3 Gbps HD/SD SDI Configurable I/O Adaptive Cable Equalizer / Cable Driver 48-TLGA -40 to 85
TI
LMH0387SLE/NOPB
3 Gbps HD/SD SDI Configurable I/O Adaptive Cable Equalizer / Cable Driver 48-TLGA -40 to 85
TI
©2020 ICPDF网 联系我们和版权申明