LMR23630QDRRRQ1 [TI]
通过汽车级认证的 SIMPLE SWITCHER® 4V 至 36V、3A 同步降压转换器 | DRR | 12 | -40 to 125;型号: | LMR23630QDRRRQ1 |
厂家: | TEXAS INSTRUMENTS |
描述: | 通过汽车级认证的 SIMPLE SWITCHER® 4V 至 36V、3A 同步降压转换器 | DRR | 12 | -40 to 125 转换器 |
文件: | 总42页 (文件大小:3588K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Support &
Community
Product
Folder
Order
Now
Tools &
Software
Technical
Documents
LMR23630-Q1
ZHCSFR2B –DECEMBER 2016–REVISED MARCH 2018
LMR23630-Q1 SIMPLE SWITCHER® 36V、3A 同步降压转换器
1 特性
2 应用
1
•
符合汽车应用 标准
•
•
•
汽车信息娱乐系统:仪表组、音响主机、抬头显示
•
具有符合 AEC-Q100 标准的下列特性:
USB 充电
一般电池供电 应用
空白
–
器件温度 1 级:-40℃ 至 +125℃ 的环境运行温
度范围
–
–
器件 HBM ESD 分类等级 2
器件 CDM ESD 分类等级:
3 说明
LMR23630-Q1 SIMPLE SWITCHER®是一款简便易用
的 36V、3A 同步降压稳压器。该器件具有 4V 至 36V
的宽输入范围, 适用于 从工业到汽车各类应用中非稳
压电源的电压调节。采用峰值电流模式控制来实现简单
控制环路补偿和逐周期电流限制。其静态电流低至
75µA,因此适用于电池供电类系统。内部环路补偿意
味着用户不用承担设计环路补偿组件的枯燥工作。这样
还能够最大限度地减少外部元件数。该器件还具有恒定
频率 FPWM 模式,可在轻载时实现较小的输出电压纹
波。该器件的扩展系列产品能够以引脚到引脚兼容的封
装提供 1A (LMR23610-Q1)、1.5A (LMR23615-Q1) 和
2.5A (LMR23625-Q1) 负载电流选项,从而可以实现简
单且最佳的 PCB 布局。利用精密使能端输入可以简化
稳压器控制和系统电源定序。保护 特性 包括逐周期电
流限制、间断模式短路保护和过多功率耗散而引起的热
关断。
–
–
带 RT 的 SOIC 和 WSON - C4B 级
带 PGOOD 的 WSON - C5 级
•
•
•
•
•
•
4V 至 36V 的输入范围
3A 持续输出电流
最短导通时间:60ns
内置补偿功能,便于使用
400kHz 固定开关频率和可调开关频率两种选择
在轻负载条件下,有脉频调制 (PFM) 和强制脉宽调
制 (PWM) 两种模式可供选项
•
•
•
•
•
•
•
与外部时钟频率同步
对于 PFM 选项,无负载条件下的静态电流为 75µA
电源正常选项
软启动至预偏置负载
支持高占空比运行模式
具有间断模式的输出短路保护
8 引脚 HSOIC 和 12 引脚 WSON 可湿侧面,具有
PowerPAD™封装选项
结合使用 LMR23630-Q1 和 WEBENCH® 电源设计
器创建定制设计
器件信息(1)
•
器件型号
封装
HSOIC (8)
WSON (12)
封装尺寸(标称值)
4.90mm × 3.90mm
3.00mm × 3.00mm
LMR23630-Q1
(1) 要了解所有不同可用选项的详细部件号,请参见数据表末尾的
可订购产品附录。
简化原理图
效率与负载间的关系,VIN = 12V,PFM 选项
VIN up to 36 V
100
CIN
VIN
90
80
70
60
BOOT
SW
EN/SYNC
AGND
CBOOT
L
VOUT
RFBT
COUT
RFBB
VCC
FB
50
CVCC
VOUT = 5 V
VOUT = 3.3 V
PGND
40
0.0001
0.001
0.01
0.1
1
10
IOUT (A)
D001
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
English Data Sheet: SNVSAR6
LMR23630-Q1
ZHCSFR2B –DECEMBER 2016–REVISED MARCH 2018
www.ti.com.cn
目录
8.3 Feature Description................................................. 11
8.4 Device Functional Modes........................................ 18
Application and Implementation ........................ 19
9.1 Application Information............................................ 19
9.2 Typical Applications ................................................ 19
1
2
3
4
5
6
7
特性.......................................................................... 1
应用.......................................................................... 1
说明.......................................................................... 1
修订历史记录 ........................................................... 2
Product Portfolio.................................................... 3
Pin Configuration and Functions......................... 3
Specifications......................................................... 4
7.1 Absolute Maximum Ratings ...................................... 4
7.2 ESD Ratings.............................................................. 4
7.3 Recommended Operating Conditions ...................... 4
7.4 Thermal Information.................................................. 5
7.5 Electrical Characteristics........................................... 5
7.6 Timing Characteristics............................................... 6
7.7 Switching Characteristics.......................................... 7
7.8 Typical Characteristics.............................................. 8
Detailed Description ............................................ 10
8.1 Overview ................................................................. 10
8.2 Functional Block Diagram ....................................... 10
9
10 Power Supply Recommendations ..................... 26
11 Layout................................................................... 26
11.1 Layout Guidelines ................................................. 26
11.2 Layout Examples................................................... 28
12 器件和文档支持 ..................................................... 29
12.1 使用 WEBENCH® 工具创建定制设计 ................... 29
12.2 接收文档更新通知 ................................................. 29
12.3 社区资源................................................................ 29
12.4 商标....................................................................... 29
12.5 静电放电警告......................................................... 29
12.6 Glossary................................................................ 29
13 机械、封装和可订购信息....................................... 29
8
4 修订历史记录
注:之前版本的页码可能与当前版本有所不同。
Changes from Revision A (April 2017) to Revision B
Page
•
•
•
•
•
•
•
•
•
•
•
•
在 12 引脚 WSON 中添加了“可湿”一词 .................................................................................................................................. 1
删除了“汽车电池稳压、工业电源、电信和数据通信系统”并修改了“应用”中的措辞 ................................................................ 1
已删除 针对市场发布从 WSON 内容中删除了“预览”;对格式进行了编辑性更新 ................................................................... 1
Updating the the drawing title for Pin Configurations and Functions for WSON with RT and WSON with PGOOD ............ 3
Corrected the column title for WSON with RT and WSON with PGOOD ............................................................................. 3
Updating the ESD Ratings to include both SOIC and WSON packages ............................................................................... 4
Changing from EN Pin to EN/SYNC Pin ............................................................................................................................... 5
Added WSON only on the Electrical Characteristic table for PGOOD................................................................................... 5
Changing the minimum value for VPG_OV from 105% to 104% .............................................................................................. 5
Adding a row for WSON Peak and Valley inductor current limit ............................................................................................ 6
Changed the min and max for minimum adjustable frequency from 180kHz and 220kHz to 150kHz and 250kHz .............. 7
Changed the min,typ, and max values for maximum adjustable frequency from 1980kHz,2200kHz, and 2420kHz to
1750kHz,2150kHz and 2425kHz ............................................................................................................................................ 7
Changes from Original (December 2016) to Revision A
Page
•
Changed the ESD HBM rating to ±2000 from ±2500 ............................................................................................................. 4
2
Copyright © 2016–2018, Texas Instruments Incorporated
LMR23630-Q1
www.ti.com.cn
ZHCSFR2B –DECEMBER 2016–REVISED MARCH 2018
5 Product Portfolio
PACKAGE
PART NUMBER
FIXED 400 kHz ADJUSTABLE FREQUENCY
POWER GOOD
FPWM
No
LMR23630AQDDARQ1
LMR23630AFQDDARQ1
LMR23630QDRRRQ1
LMR23630FQDRRRQ1
LMR23630APQDRRRQ1
Yes
Yes
No
No
No
No
No
SOIC (8)
Yes
No
Yes
Yes
No
No
WSON (12) (Pin 6 is RT)
No
No
Yes
No
WSON (12) (Pin 6 is PGOOD)
Yes
Yes
6 Pin Configuration and Functions
DRR Package
DDA Package
DRR Package
12-Pin WSON With PGOOD and Thermal
8-Pin SOIC With PowerPAD
12-Pin WSON With RT and Thermal Pad
Pad
Top View
Top View
Top View
PGND
PGND
VIN
1
2
3
4
5
6
12
11
10
9
SW
BOOT
VCC
SW
SW
1
2
3
8
7
PGND
NC
SW
SW
1
2
3
4
5
6
12
11
10
9
NC
VIN
VIN
Thermal
Pad
9
BOOT
VCC
VIN
BOOT
VCC
FB
PAD
13
PAD
13
6
5
AGND
VIN
EN/SYNC
FB
8
EN/SYNC
AGND
FB
4
8
EN/SYNC
AGND
7
PGOOD
7
RT
Pin Functions
PIN
I/O(1)
DESCRIPTION
WSON
With
PGOOD
WSON
With RT
NAME
SOIC
Switching output of the regulator. Internally connected to both power MOSFETs.
Connect to power inductor.
SW
1
2
1, 2
1, 2
3
P
P
Boot-strap capacitor connection for high-side driver. Connect a high-quality, 100-nF
capacitor from BOOT to SW.
BOOT
3
4
Internal bias supply output for bypassing. Connect a 2.2-μF, 16-V or higher
capacitance bypass capacitor from this pin to AGND. Do not connect external
loading to this pin. Never short this pin to ground during operation.
VCC
3
4
P
Feedback input to regulator, connect the midpoint of feedback resistor divider to this
pin.
FB
4
5
N/A
6
5
6
A
A
A
Connect a resistor RT from this pin to AGND to program switching frequency. Leave
floating for 400-kHz default switching frequency.
RT
N/A
N/A
Open drain output for power-good flag. Use a 10-kΩ to 100-kΩ pullup resistor to
logic rail or other DC voltage no higher than 12 V.
PGOOD
N/A
Enable input to regulator. High = On, Low = Off. Can be connected to VIN. Do not
float. Adjust the input undervoltage lockout with two resistors. The internal oscillator
can be synchronized to an external clock by coupling a positive pulse into this pin
through a small coupling capacitor. See Enable/Synchronization for details.
EN/SYNC
5
8
8
A
Analog ground pin. Ground reference for internal references and logic. Connect to
system ground.
AGND
VIN
6
7
7
7
G
P
9, 10
9, 10
Input supply voltage.
Power ground pin, connected internally to the low side power FET. Connect to
system ground, PAD, AGND, ground pins of CIN and COUT. Path to CIN must be as
short as possible.
PGND
8
12
12
G
Low impedance connection to AGND. Connect to PGND on PCB. Major heat
dissipation path of the die. Must be used for heat sinking to ground plane on PCB.
PAD
NC
9
13
11
13
11
G
N/A
N/A Not for use. Leave this pin floating.
(1) A = Analog, P = Power, G = Ground.
Copyright © 2016–2018, Texas Instruments Incorporated
3
LMR23630-Q1
ZHCSFR2B –DECEMBER 2016–REVISED MARCH 2018
www.ti.com.cn
7 Specifications
7.1 Absolute Maximum Ratings
Over the recommended operating junction temperature range of –40°C to +125°C (unless otherwise noted)(1)
PARAMETER
VIN to PGND
MIN
–0.3
–5.5
–0.3
–0.3
–0.3
–0.3
–1
MAX
42
UNIT
EN/SYNC to AGND
FB to AGND
VIN + 0.3
4.5
Input voltages
V
RT to AGND
4.5
PGOOD to AGND
AGND to PGND
SW to PGND
15
0.3
VIN + 0.3
42
SW to PGND less than 10-ns transients
BOOT to SW
-5
Output voltages
V
–0.3
–0.3
–40
–65
5.5
4.5(2)
VCC to AGND
Junction temperature, TJ
Storage temperature, Tstg
150
°C
°C
150
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) In shutdown mode, the VCC to AGND maximum value is 5.25 V.
7.2 ESD Ratings
VALUE
±2000
±2500
UNIT
Human-body model (HBM) for SOIC(1)
Human-body model (HBM) for WSON with RT or
PGOOD
V(ESD)
Electrostatic discharge
V
Charged-device model (CDM) for SOIC
±1000
±1000
±750
Charged-device model (CDM) for WSON with RT
Charged-device model (CDM) for WSON with PGOOD
(1) AEC Q100-002 indicates that HBM stressing shall be in accordance with the ANSI/ESDA/JEDEC JS-001 specification.
7.3 Recommended Operating Conditions
Over the recommended operating junction temperature range of –40°C to +125°C (unless otherwise noted)
(1)
MIN
4
MAX
36
36
1.2
12
1
UNIT
VIN
EN/SYNC
FB
–5
–0.3
–0.3
0
Input voltage
V
PGOOD
Input current
PGOOD pin current
mA
V
Output voltage, VOUT
Output current, IOUT
1
28
3
0
A
Operating junction temperature, TJ
–40
125
°C
(1) Recommended Operating Ratings indicate conditions for which the device is intended to be functional, but do not ensure specific
performance limits. For specified specifications, see Electrical Characteristics.
4
Copyright © 2016–2018, Texas Instruments Incorporated
LMR23630-Q1
www.ti.com.cn
ZHCSFR2B –DECEMBER 2016–REVISED MARCH 2018
7.4 Thermal Information
LMR23630-Q1
THERMAL METRIC(1)(2)
DDA (SOIC)
8 PINS
42.0
DRR (WSON)
12 PINS
41.5
UNIT
RθJA
Junction-to-ambient thermal resistance
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
RθJC(top)
RθJB
5.9
0.3
23.4
16.5
ψJT
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
45.8
39.1
ψJB
3.6
3.4
RθJC(bot)
23.4
16.3
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
(2) Determine power rating at a specific ambient temperature TA with a maximum junction temperature (TJ) of 125°C, which is illustrated in
Recommended Operating Conditions section.
7.5 Electrical Characteristics
Limits apply over the recommended operating junction temperature (TJ) range of –40°C to +125°C, unless otherwise stated.
Minimum and Maximum limits are specified through test, design or statistical correlation. Typical values represent the most
likely parametric norm at TJ = 25°C, and are provided for reference purposes only.
PARAMETER
POWER SUPPLY (VIN PIN)
TEST CONDITIONS
MIN
TYP
MAX UNIT
VIN
Operation input voltage
4
3.3
2.9
36
3.9
3.5
V
V
Rising threshold
3.7
3.3
VIN_UVLO
Undervoltage lockout thresholds
Falling threshold
VEN = 0 V, VIN = 12 V, TJ = –40°C to
125°C
ISHDN
IQ
Shutdown supply current
2
4
μA
μA
Operating quiescent current (non-
switching)
VIN = 12 V, VFB = 1.1 V, TJ = –40°C to
125°C, PFM mode
75
ENABLE (EN/SYNC PIN)
VEN_H
Enable rising threshold voltage
1.4
0.4
1.55
0.4
1.7
V
V
VEN_HYS
VWAKE
Enable hysteresis voltage
Wake-up threshold
V
VIN = 4 V to 36 V, VEN= 2 V
VIN = 4 V to 36 V, VEN= 36 V
10
100
1
nA
μA
IEN
Input leakage current at EN pin
VOLTAGE REFERENCE (FB PIN)
VIN = 4 V to 36 V, TJ = 25°C
VIN = 4 V to 36 V, TJ = –40°C to 125°C
VFB= 1 V
0.985
0.98
1
1
1.015
1.02
VREF
Reference voltage
V
ILKG_FB
Input leakage current at FB pin
10
nA
POWER GOOD (PGOOD PIN) WSON Only
Power-good flag overvoltage tripping
threshold
% of reference voltage
% of reference voltage
% of reference voltage
VPG_OV
104% 107%
110%
Power-good flag undervoltage tripping
threshold
VPG_UV
92%
94%
96.5%
VPG_HYS
Power-good flag recovery hysteresis
1.5%
50 μA pullup to PGOOD pin, VEN = 0 V, TJ
= 25°C
V
V
VIN_PG_MIN
Minimum VIN for valid PGOOD output
1.5
0.4
0.4
50 μA pullup to PGOOD pin, VIN = 1.5 V,
VEN = 0 IN
V
VPG_LOW
PGOOD low level output voltage
0.5 mA pullup to PGOOD pin, V =13.5 V,
VEN = 0 V
Copyright © 2016–2018, Texas Instruments Incorporated
5
LMR23630-Q1
ZHCSFR2B –DECEMBER 2016–REVISED MARCH 2018
www.ti.com.cn
Electrical Characteristics (continued)
Limits apply over the recommended operating junction temperature (TJ) range of –40°C to +125°C, unless otherwise stated.
Minimum and Maximum limits are specified through test, design or statistical correlation. Typical values represent the most
likely parametric norm at TJ = 25°C, and are provided for reference purposes only.
PARAMETER
INTERNAL LDO (VCC PIN)
TEST CONDITIONS
MIN
TYP
MAX UNIT
VCC
Internal LDO output voltage
4.1
3.2
2.8
V
Rising threshold
2.8
2.4
3.6
V
VCC_UVLO
VCC undervoltage lockout thresholds
Falling threshold
3.2
CURRENT LIMIT
IHS_LIMIT Peak inductor current limit
HSOIC package
WSON package
HSOIC package
WSON package
3.8
4
5
5.5
6.2
A
6.6
2.9
2.9
3.6
4.6
4.2
A
ILS_LIMIT
Valley inductor current limit
3.6
IL_ZC
Zero cross current limit
–0.04
–2
A
A
IL_NEG
Negative current limit (FPWM option)
–2.7
–1.3
INTEGRATED MOSFETS
HSOIC package, VIN = 12 V, IOUT = 1 A
WSON package, VIN = 12 V, IOUT = 1 A
HSOIC package, VIN = 12 V, IOUT = 1 A
WSON package, VIN = 12 V, IOUT = 1 A
185
160
105
95
RDS_ON_HS High-side MOSFET ON-resistance
mΩ
mΩ
RDS_ON_LS
Low-side MOSFET ON-resistance
THERMAL SHUTDOWN
TSHDN Thermal shutdown threshold
THYS Hysteresis
162
170
15
178
°C
°C
7.6 Timing Characteristics
Over the recommended operating junction temperature range of –40°C to +125°C (unless otherwise noted)
MIN
NOM
MAX UNIT
HICCUP MODE
Number of cycles that LS current limit is tripped
to enter Hiccup mode
Cycle
s
(1)
NOC
64
SOIC package
5
TOC
Hiccup retry delay time
ms
WSON package
10
SOFT START
SOIC package
1
2
6
3
Internal soft-start time. The time of internal
reference to increase from 0 V to 1 V
TSS
ms
WSON package
POWER GOOD
TPGOOD_RISE
TPGOOD_FALL
Power-good flag rising transition deglitch delay
Power-good flag falling transition deglitch delay
150
18
μs
μs
(1) Specified by design.
6
Copyright © 2016–2018, Texas Instruments Incorporated
LMR23630-Q1
www.ti.com.cn
ZHCSFR2B –DECEMBER 2016–REVISED MARCH 2018
7.7 Switching Characteristics
Over the recommended operating junction temperature range of –40°C to +125°C (unless otherwise noted)
PARAMETER
TEST CONDITION
MIN
TYP
MAX UNIT
SW (SW PIN)
TON_MIN
Minimum turnon time
Minimum turnoff time
60
90
ns
ns
(1)
TOFF_MIN
100
OSCILLATOR (RT and EN/SYNC PIN)
fSW_DEFAULT Oscillator default frequency
Fixed frequency option or RT pin open
circuit
kHz
340
400
460
fADJ
Minimum adjustable frequency
Maximum adjustable frequency
SYNC frequency range
RT = 198 kΩ with 1% accuracy
RT = 17.8 kΩ with 1% accuracy
150
1750
200
200
250 kHz
2425 kHz
2200 kHz
2150
fSYNC
VSYNC
Amplitude of SYNC clock AC signal
(measured at SYNC pin)
V
2.8
5.5
TSYNC_MIN
Minimum sync clock ON- and OFF-time
100
ns
(1) Specified by design.
Copyright © 2016–2018, Texas Instruments Incorporated
7
LMR23630-Q1
ZHCSFR2B –DECEMBER 2016–REVISED MARCH 2018
www.ti.com.cn
7.8 Typical Characteristics
Unless otherwise specified the following conditions apply: VIN = 12 V, fSW = 400 kHz, L = 8.2 µH, COUT = 150 µF, TA = 25°C.
100
90
80
70
60
50
40
30
20
10
0
100
90
80
70
60
50
40
30
20
10
0
PFM, VIN = 12 V
PFM, VIN = 24 V
PFM, VIN = 36 V
FPWM, VIN = 12 V
FPWM, VIN = 24 V
FPWM, VIN = 36 V
PFM, VIN = 12 V
PFM, VIN = 24 V
PFM, VIN = 36 V
FPWM, VIN = 12 V
FPWM, VIN = 24 V
FPWM, VIN = 36 V
1E-5
0.0001
0.001
0.01
0.1
1
10
1E-5
0.0001
0.001
0.01
0.1
1
10
IOUT (A)
IOUT (A)
D001
D002
fSW = 400 kHz
VOUT = 5 V
fSW = 400 kHz
VOUT = 3.3 V
Figure 1. Efficiency vs Load Current
Figure 2. Efficiency vs Load Current
100
90
80
70
60
50
40
30
20
10
0
100
90
80
70
60
50
40
30
20
10
0
PFM, VIN = 12 V
PFM, VIN = 12 V
PFM, VIN = 24 V
PFM, VIN = 36 V
FPWM, VIN = 12 V
FPWM, VIN = 24 V
FPWM, VIN = 36 V
PFM, VIN = 24 V
PFM, VIN = 36 V
FPWM, VIN = 12 V
FPWM, VIN = 24 V
FPWM, VIN = 36 V
1E-5
0.0001
0.001
0.01
0.1
1
10
1E-5
0.0001
0.001
0.01
0.1
1
10
IOUT (A)
IOUT (A)
D003
D004
fSW = 200 kHz
(Sync)
VOUT = 5 V
fSW = 200 kHz
(Sync)
VOUT = 3.3 V
Figure 3. Efficiency vs Load Current
Figure 4. Efficiency vs Load Current
5.09
5.08
5.07
5.06
5.05
5.04
5.03
5.02
5.01
5
5.015
5.01
5.005
5
VIN = 12 V
VIN = 24 V
VIN = 36 V
VIN = 12 V
VIN = 24 V
VIN = 36 V
4.99
0
0.5
1
1.5
2
2.5
3
0
0.5
1
1.5
2
2.5
3
IOUT (A)
IOUT (A)
D004
D005
PFM Option
VOUT = 5 V
FPWM Option
VOUT = 5 V
Figure 5. Load Regulation
Figure 6. Load Regulation
8
Copyright © 2016–2018, Texas Instruments Incorporated
LMR23630-Q1
www.ti.com.cn
ZHCSFR2B –DECEMBER 2016–REVISED MARCH 2018
Typical Characteristics (continued)
Unless otherwise specified the following conditions apply: VIN = 12 V, fSW = 400 kHz, L = 8.2 µH, COUT = 150 µF, TA = 25°C.
5.5
3.6
3.3
3
5
4.5
4
2.7
IOUT = 0.5 A
IOUT = 1.0 A
IOUT = 2.0 A
IOUT = 3.0 A
IOUT = 0.5 A
IOUT = 1.0 A
IOUT = 2.0 A
IOUT = 3.0 A
3.5
3
2.4
4
4.5
5
5.5
6
3.3
3.5
3.7
3.9
4.1
4.3
4.5
VIN (V)
VIN (V)
D006
D007
VOUT = 5 V
VOUT = 3.3 V
Figure 8. Dropout Curve
Figure 7. Dropout Curve
80
75
70
65
60
3.67
3.66
3.65
3.64
3.63
3.62
3.61
-50
0
50
100
150
-50
0
50
100
150
Temperature (°C)
Temperature (°C)
D008
D009
VIN = 12 V
VFB = 1.1 V
Figure 9. IQ vs Junction Temperature
Figure 10. VIN UVLO Rising Threshold vs Junction
Temperature
5.5
5
0.425
LS Limit
HS Limit
0.42
0.415
0.41
4.5
4
3.5
3
-50
0
50
100
150
-50
0
50
100
150
Temperature (°C)
Temperature (°C)
D010
D011
VIN = 12 V
Figure 11. VIN UVLO Hysteresis vs Junction Temperature
Figure 12. HS and LS Current Limit vs Junction
Temperature
Copyright © 2016–2018, Texas Instruments Incorporated
9
LMR23630-Q1
ZHCSFR2B –DECEMBER 2016–REVISED MARCH 2018
www.ti.com.cn
8 Detailed Description
8.1 Overview
The LMR23630-Q1 SIMPLE SWITCHER® regulator is an easy-to-use synchronous step-down DC/DC converter
operating from 4-V to 36-V supply voltage. The device is capable of delivering up to 3-A DC load current with
good thermal performance in a small solution size. For both SOIC and WSON packages, an extended family is
available in multiple current options from 1-A to 3-A in pin-to-pin compatible packages.
The LMR23630-Q1 employs constant-frequency peak-current-mode control. The device enters PFM mode at
light load to achieve high efficiency. A user-selectable FPWM option is provided to achieve low output voltage
ripple, tight output voltage regulation, and constant switching frequency. The device is internally compensated,
which reduces design time and requires few external components. The switching frequency is fixed 400 kHz. For
the option which has an RT pin, the switching frequency is adjustable from 200 kHz to 2.2 MHz. Also, the
LMR23630-Q1 is capable of synchronization to an external clock within the range of 200 kHz to 2.2 MHz.
Additional features such as precision enable, power-good flag, and internal soft start provide a flexible and easy-
to-use solution for a wide range of applications. Protection features include thermal shutdown, VIN and VCC
undervoltage lockout, cycle-by-cycle current limit, and hiccup-mode short-circuit protection.
The family requires very few external components and has a pinout designed for simple, optimum PCB layout.
8.2 Functional Block Diagram
VCC
EN/SYNC
SYNC Signal
SYNC
VCC
LDO
VIN
Detector
Enable
Precision
Enable
CBOOT
Internal
SS
HS I Sense
EA
REF
Rc
Cc
TSD
UVLO
(PGOOD)
PWM CONTROL LOGIC
PFM
Detector
SW
OV/UV
Detector
FB
Slope
Comp
Freq
Foldback
Zero
Cross
HICCUP
Detector
AGND
SYNC Signal
(RT)
Oscillator
LS I Sense
FB
PGND
Copyright © 2016, Texas Instruments Incorporated
10
Copyright © 2016–2018, Texas Instruments Incorporated
LMR23630-Q1
www.ti.com.cn
ZHCSFR2B –DECEMBER 2016–REVISED MARCH 2018
8.3 Feature Description
8.3.1 Fixed-Frequency Peak-Current-Mode Control
The following operating description of the LMR23630-Q1 refers to the Functional Block Diagram and to the
waveforms in Figure 13. LMR23630-Q1 is a step-down synchronous buck regulator with integrated high-side
(HS) and low-side (LS) switches (synchronous rectifier). The LMR23630-Q1 supplies a regulated output voltage
by turning on the HS and LS NMOS switches with controlled duty cycle. During high-side switch ON-time, the
SW pin voltage swings up to approximately VIN, and the inductor current iL increase with linear slope (VIN – VOUT
)
/ L. When the HS switch is turned off by the control logic, the LS switch is turned on after an anti-shoot-through
dead time. Inductor current discharges through the LS switch with a slope of –VOUT / L. The control parameter of
a buck converter is defined as duty cycle D = tON / TSW, where tON is the high-side switch ON-time and TSW is the
switching period. The regulator control loop maintains a constant output voltage by adjusting the duty cycle D. In
an ideal buck converter, where losses are ignored, D is proportional to the output voltage and inversely
proportional to the input voltage: D = VOUT / VIN.
VSW
D = tON/ TSW
VIN
tON
tOFF
t
0
-VD
TSW
iL
ILPK
IOUT
DiL
t
0
Figure 13. SW Node and Inductor Current Waveforms in
Continuous Conduction Mode (CCM)
The LMR23630-Q1 employs fixed-frequency peak-current-mode control. A voltage feedback loop is used to get
accurate DC voltage regulation by adjusting the peak current command based on voltage offset. The peak
inductor current is sensed from the high-side switch and compared to the peak current threshold to control the
ON time of the high-side switch. The voltage feedback loop is internally compensated, which allows for fewer
external components, makes it easy to design, and provides stable operation with almost any combination of
output capacitors. The regulator operates with fixed switching frequency at normal load condition. At light load
condition, the LMR23630-Q1 operates in PFM mode to maintain high efficiency (PFM option) or in FPWM mode
for low output voltage ripple, tight output voltage regulation, and constant switching frequency (FPWM option).
8.3.2 Adjustable Frequency
For adjustable switching frequency option of LMR23630-Q1. The switching frequency can be programmed by the
impedance RT from the RT pin to ground. The frequency is inversely proportional to the RT resistance. The RT
pin can be left floating, and the LMR23630-Q1 will operate at 400-kHz default switching frequency. The RT pin is
not designed to be shorted to ground. For a desired requency, typical RT resistance can be found by Equation 1.
Table 1 gives typical RT values for a given fSW
.
RT(kΩ) = 40200 / fSW(kHz) – 0.6
(1)
Copyright © 2016–2018, Texas Instruments Incorporated
11
LMR23630-Q1
ZHCSFR2B –DECEMBER 2016–REVISED MARCH 2018
www.ti.com.cn
Feature Description (continued)
250
200
150
100
50
0
0
500
1000
1500
2000
2500
Switching Frequency (kHz)
C008
Figure 14. RT vs Frequency Curve
Table 1. Typical Frequency Setting RT Resistance
fSW (kHz)
RT (kΩ)
200
200
350
115
500
78.7
53.6
39.2
26.1
19.6
17.8
750
1000
1500
2000
2200
8.3.3 Adjustable Output Voltage
A precision 1-V reference voltage is used to maintain a tightly regulated output voltage over the entire operating
temperature range. The output voltage is set by a resistor divider from output voltage to the FB pin. TI
recommends using 1% tolerance resistors with a low temperature coefficient for the FB divider. Select the low-
side resistor RFBB for the desired divider current and use Equation 2 to calculate high-side RFBT. RFBT in the
range from 10 kΩ to 100 kΩ is recommended for most applications. A lower RFBT value can be used if static
loading is desired to reduce VOUT offset in PFM operation. Lower RFBT reduces efficiency at very light load. Less
static current goes through a larger RFBT and might be more desirable when light load efficiency is critical. But
RFBT larger than 1 MΩ is not recommended because it makes the feedback path more susceptible to noise.
Larger RFBT value requires more carefully designed feedback path on the PCB. The tolerance and temperature
variation of the resistor dividers affect the output voltage regulation.
V
OUT
R
FBT
FBB
FB
R
Figure 15. Output Voltage Setting
VOUT - VREF
RFBT
=
ìRFBB
VREF
(2)
12
Copyright © 2016–2018, Texas Instruments Incorporated
LMR23630-Q1
www.ti.com.cn
ZHCSFR2B –DECEMBER 2016–REVISED MARCH 2018
8.3.4 Enable/Synchronization
The voltage on the EN pin controls the ON or OFF operation of LMR23630-Q1. A voltage less than 1 V (typical)
shuts the device down while a voltage higher than 1.6 V (typical) is required to start the regulator. The EN/SYNC
pin is an input and cannot be left open or floating. The simplest way to enable the operation of the LMR23630-
Q1 is to connect the EN to VIN. This allows self-start-up of the LMR23630-Q1 when VIN is within the operation
range.
Many applications benefit from the employment of an enable divider RENT and RENB (Figure 16) to establish a
precision system UVLO level for the converter. System UVLO can be used for supplies operating from utility
power as well as battery power. It can be used for sequencing, ensuring reliable operation, or supply protection,
such as a battery discharge level. An external logic signal can also be used to drive EN input for system
sequencing and protection.
VIN
RENT
EN/SYNC
RENB
Figure 16. System UVLO by Enable Divider
The EN pin also can be used to synchronize the internal oscillator to an external clock. The internal oscillator can
be synchronized by AC coupling a positive edge into the EN pin. The AC coupled peak-to-peak voltage at the EN
pin must exceed the SYNC amplitude threshold of 2.8 V (typical) to trip the internal synchronization pulse
detector, and the minimum SYNC clock ON and OFF time must be longer than 100ns (typ). A 3.3 V or a higher
amplitude pulse signal coupled through a 1 nF capacitor CSYNC is a good starting point. Keeping RENT // RENB
(RENT parallel with RENB) in the 100-kΩ range is a good choice. RENT is required for this synchronization circuit,
but RENB can be left unmounted if system UVLO is not needed. LMR23630-Q1 switching action can be
synchronized to an external clock from 200 kHz to 2.2 MHz. Figure 18 and Figure 19 show the device
synchronized to an external system clock.
VIN
RENT
CSYNC
EN/SYNC
RENB
Clock
Source
Figure 17. Synchronize to External Clock
Copyright © 2016–2018, Texas Instruments Incorporated
13
LMR23630-Q1
ZHCSFR2B –DECEMBER 2016–REVISED MARCH 2018
www.ti.com.cn
Figure 18. Synchronizing in PWM Mode
Figure 19. Synchronizing in PFM Mode
8.3.5 VCC, UVLO
The LMR23630-Q1 integrates an internal LDO to generate VCC for control circuitry and MOSFET drivers. The
nominal voltage for VCC is 4.1 V. The VCC pin is the output of an LDO and must be properly bypassed. Place a
high-quality ceramic capacitor with a value of 2.2 µF to 10 µF, 16 V or higher rated voltage as close as possible
to VCC and grounded to the exposed PAD and ground pins. Do not load the VCC output pin or short to ground
during operation. Shorting VCC to ground during operation may cause damage to the LMR23630-Q1.
VCC undervoltage lockout (UVLO) prevents the LMR23630-Q1 from operating until the VCC voltage exceeds 3.2
V (typical). The VCC UVLO threshold has 400 mV (typical) of hysteresis to prevent undesired shutdown due to
temporary VIN drops.
8.3.6 Minimum ON-time, Minimum OFF-time and Frequency Foldback at Dropout Conditions
Minimum ON-time, TON_MIN, is the smallest duration of time that the HS switch can be on. TON_MIN is typically 60
ns in the LMR23630-Q1. Minimum OFF-time, TOFF_MIN, is the smallest duration that the HS switch can be off.
TOFF_MIN is typically 100 ns in the LMR23630-Q1. In CCM operation, TON_MIN and TOFF_MIN limit the voltage
conversion range given a selected switching frequency.
The minimum duty cycle allowed is:
DMIN = TON_MIN × fSW
(3)
And the maximum duty cycle allowed is:
DMAX = 1 – TOFF_MIN × fSW
(4)
Given fixed TON_MIN and TOFF_MIN, the higher the switching frequency the narrower the range of the allowed duty
cycle. In the LMR23630-Q1, a frequency foldback scheme is employed to extend the maximum duty cycle when
TOFF_MIN is reached. The switching frequency decreases once longer duty cycle is needed under low VIN
conditions. Wide range of frequency foldback allows the LMR23630-Q1 output voltage stay in regulation with a
much lower supply voltage VIN. This leads to a lower effective dropout voltage.
Given an output voltage, the choice of the switching frequency affects the allowed input voltage range, solution
size and efficiency. The maximum operation supply voltage can be found by:
VOUT
V
=
IN_MAX
f
ì TON_MIN
SW
(5)
At lower supply voltage, the switching frequency will decrease once TOFF_MIN is tripped. The minimum VIN without
frequency foldback can be approximated by:
VOUT
V
=
IN_MIN
1- f
ì TOFF _MIN
SW
(6)
Taking considerations of power losses in the system with heavy load operation, VIN_MAX is higher than the result
calculated in Equation 5. With frequency foldback, VIN_MIN is lowered by decreased fSW
.
14
Copyright © 2016–2018, Texas Instruments Incorporated
LMR23630-Q1
www.ti.com.cn
ZHCSFR2B –DECEMBER 2016–REVISED MARCH 2018
450
400
350
300
250
200
150
100
50
IOUT = 0.5 A
IOUT = 1.0 A
IOUT = 2.0 A
IOUT = 3.0 A
0
4.6
4.8
5
5.2
5.4
5.6
5.8
6
6.2
6.4
VIN (V)
D013
Figure 20. Frequency Foldback at Dropout (VOUT = 5 V, fSW = 400 kHz)
8.3.7 Power Good (PGOOD)
The power-good version of LMR23630-Q1 has a built-in power-good flag shown on PGOOD pin to indicate
whether the output voltage is within its regulation level. The PGOOD signal can be used for start-up sequencing
of multiple rails or fault protection. The PGOOD pin is an open-drain output that requires a pullup resistor to an
appropriate DC voltage. Voltage detected by the PGOOD pin must never exceed 15 V, and the maximum current
into this pin must be limited to 1 mA. A typical range of pullup resistor value is 10 kΩ to 100 kΩ.
When the FB voltage is within the power-good band, +6% above and –6% below the internal reference voltage
VREF typically, the PGOOD switch is turned off, and the PGOOD voltage is as high as the pulled-up voltage.
When the FB voltage is outside of the tolerance band, +7% above or –7% below VREF typically, the PGOOD
switch is turned on, and the PGOOD pin voltage is pulled low to indicate power bad. A glitch filter prevents false-
flag operation for short excursions in the output voltage, such as during line and load transients. The values for
the various filter and delay times can be found in the Timing Characteristics table. Power-good operation can
best be understood by reference to Figure 21.
VREF
107%
106%
94%
93%
PGOOD
High
Low
Figure 21. Power-Good Flag
Copyright © 2016–2018, Texas Instruments Incorporated
15
LMR23630-Q1
ZHCSFR2B –DECEMBER 2016–REVISED MARCH 2018
www.ti.com.cn
8.3.8 Internal Compensation and CFF
The LMR23630-Q1 is internally compensated as shown in Functional Block Diagram. The internal compensation
is designed such that the loop response is stable over the entire operating frequency and output voltage range.
Depending on the output voltage, the compensation loop phase margin can be low with all ceramic capacitors.
An external feed-forward capacitor CFF is recommended to be placed in parallel with the top resistor divider RFBT
for optimum transient performance.
VOUT
CFF
RFBT
FB
RFBB
Figure 22. Feedforward Capacitor for Loop Compensation
The feed-forward capacitor CFF in parallel with RFBT places an additional zero before the cross over frequency of
the control loop to boost phase margin. The zero frequency can be found by
1
fZ _ CFF
=
2pìCFF ìRFBT
(7)
An additional pole is also introduced with CFF at the frequency of
1
fP _ CFF
=
2pìCFF ìRFBT //RFBB
(8)
The zero fZ_CFF adds phase boost at the crossover frequency and improves transient response. The pole fP-CFF
helps maintaining proper gain margin at frequency beyond the crossover. Table 2 lists the combination of COUT
,
CFF and RFBT for typical applications, designs with similar COUT but RFBT other than recommended value, adjust
CFF such that (CFF × RFBT) is unchanged and adjust RFBB such that (RFBT / RFBB) is unchanged.
Designs with different combinations of output capacitors need different CFF. Different types of capacitors have
different equivalent series resistance (ESR). Ceramic capacitors have the smallest ESR and need the most CFF.
Electrolytic capacitors have much larger ESR and the ESR zero frequency would be low enough to boost the
phase up around the crossover frequency. Designs using mostly electrolytic capacitors at the output may not
need any CFF.
1
fZ _ESR
=
2pìC
ìESR
OUT
(9)
The CFF creates a time constant with RFBT that couples in the attenuate output voltage ripple to the FB node. If
the CFF value is too large, it can couple too much ripple to the FB and affect VOUT regulation. Therefore, calculate
CFF based on output capacitors used in the system. At cold temperatures, the value of CFF might change based
on the tolerance of the chosen component. This may reduce its impedance and ease noise coupling on the FB
node. To avoid this, more capacitance can be added to the output or the value of CFF can be reduced.
8.3.9 Bootstrap Voltage (BOOT)
The LMR23630-Q1 provides an integrated bootstrap voltage regulator. A small capacitor between the BOOT and
SW pins provides the gate-drive voltage for the high-side MOSFET. The BOOT capacitor is refreshed when the
high-side MOSFET is off and the low-side switch conducts. The recommended value of the BOOT capacitor is
0.1 μF or higher. TI recommends ceramic capacitor with an X7R or X5R grade dielectric with a voltage rating of
16 V or higher for stable performance over temperature and voltage.
8.3.10 Overcurrent and Short-Circuit Protection
The LMR23630-Q1 is protected from overcurrent conditions by cycle-by-cycle current limit on both the peak and
valley of the inductor current. Hiccup mode will be activated if a fault condition persists to prevent over-heating.
16
Copyright © 2016–2018, Texas Instruments Incorporated
LMR23630-Q1
www.ti.com.cn
ZHCSFR2B –DECEMBER 2016–REVISED MARCH 2018
High-side MOSFET overcurrent protection is implemented by the nature of the peak-current-mode control. The
HS switch current is sensed when the HS is turned on after a set blanking time. The HS switch current is
compared to the output of the error amplifier (EA) minus slope compensation every switching cycle. See
Functional Block Diagram for more details. The peak current of HS switch is limited by a clamped maximum peak
current threshold IHS_LIMIT which is constant. So the peak current limit of the HS switch is not affected by the
slope compensation and remains constant over the full duty-cycle range.
The current going through LS MOSFET is also sensed and monitored. When the LS switch turns on, the inductor
current begins to ramp down. The LS switch is not turned OFF at the end of a switching cycle if its current is
above the LS current limit ILS_LIMIT. The LS switch is kept ON so that inductor current keeps ramping down, until
the inductor current ramps below the LS current limit ILS_LIMIT. The LS switch is then turned OFF, and the HS
switch turned on after a dead time. This is somewhat different than the more typical peak-current limit, and
results in Equation 10 for the maximum load current.
V - V
(
)
ì
VOUT
IN
OUT
IOUT _MAX = ILS _LIMIT
+
2ì fSW ìL
V
IN
(10)
If the current of the LS switch is higher than the LS current limit for 64 consecutive cycles, hiccup current-
protection mode is activated. In hiccup mode, the regulator is shut down and kept off for 5 ms typically before the
LMR23630-Q1 tries to start again. If overcurrent or short-circuit fault condition still exist, hiccup repeats until the
fault condition is removed. Hiccup mode reduces power dissipation under severe overcurrent conditions,
prevents over-heating and potential damage to the device.
For FPWM option, the inductor current is allowed to go negative. If this current exceeds IL_NEG, the LS switch is
turned off until the next clock cycle. This is used to protect the LS switch from excessive negative current.
8.3.11 Thermal Shutdown
The LMR23630-Q1 provides an internal thermal shutdown to protect the device when the junction temperature
exceeds 170°C (typical). The device is turned off when thermal shutdown activates. Once the die temperature
falls below 155°C (typical), the device reinitiates the power-up sequence controlled by the internal soft-start
circuitry.
Copyright © 2016–2018, Texas Instruments Incorporated
17
LMR23630-Q1
ZHCSFR2B –DECEMBER 2016–REVISED MARCH 2018
www.ti.com.cn
8.4 Device Functional Modes
8.4.1 Shutdown Mode
The EN pin provides electrical ON and OFF control for the LMR23630-Q1. When VEN is below 1 V (typical), the
device is in shutdown mode. The LMR23630-Q1 also employs VIN and VCC UVLO protection. If VIN or VCC
voltage is below their respective UVLO level, the regulator is turned off.
8.4.2 Active Mode
The LMR23630-Q1 is in active mode when VEN is above the precision enable threshold, VIN and VCC are above
their respective UVLO level. The simplest way to enable the LMR23630-Q1 is to connect the EN pin to VIN pin.
This allows self startup when the input voltage is in the operating range: 4 V to 36 V. See VCC, UVLO and
Enable/Synchronization for details on setting these operating levels.
In active mode, depending on the load current, the LMR23630-Q1 is in one of four modes:
1. Continuous conduction mode (CCM) with fixed switching frequency when load current is above half of the
peak-to-peak inductor current ripple (for both PFM and FPWM options).
2. Discontinuous conduction mode (DCM) with fixed switching frequency when load current is lower than half of
the peak-to-peak inductor current ripple in CCM operation (only for PFM option).
3. Pulse frequency modulation mode (PFM) when switching frequency is decreased at very light load (only for
PFM option).
4. Forced pulse width modulation mode (FPWM) with fixed switching frequency even at light load (only for
FPWM option).
8.4.3 CCM Mode
CCM operation is employed in the LMR23630-Q1 when the load current is higher than half of the peak-to-peak
inductor current. In CCM operation, the frequency of operation is fixed, output voltage ripple will be at a minimum
in this mode and the maximum output current of 3 A can be supplied by the LMR23630-Q1.
8.4.4 Light Load Operation (PFM Option)
For PFM option, when the load current is lower than half of the peak-to-peak inductor current in CCM, the
LMR23630-Q1 operates in DCM, also known as Diode Emulation Mode (DEM). In DCM, the LS switch is turned
off when the inductor current drops to IL_ZC (–40 mA typical). Both switching losses and conduction losses are
reduced in DCM, compared to forced PWM operation at light load.
At even lighter current loads, PFM is activated to maintain high efficiency operation. When either the minimum
HS switch ON-time (tON_MIN ) or the minimum peak inductor current IPEAK_MIN (300 mA typical) is reached, the
switching frequency decreases to maintain regulation. In PFM, switching frequency is decreased by the control
loop when load current reduces to maintain output voltage regulation. Switching loss is further reduced in PFM
operation due to less frequent switching actions. The external clock synchronizing is not be valid when
LMR23630-Q1 enters into PFM mode.
8.4.5 Light Load Operation (FPWM Option)
For FPWM option, LMR23630-Q1 is locked in PWM mode at full load range. This operation is maintained, even
at no-load, by allowing the inductor current to reverse its normal direction. This mode trades off reduced light
load efficiency for low output voltage ripple, tight output voltage regulation, and constant switching frequency. In
this mode, a negative current limit of IL_NEG is imposed to prevent damage to the regulators LS FET. When in
FPWM mode the converter synchronizes to any valid clock signal on the EN/SYNC input.
18
Copyright © 2016–2018, Texas Instruments Incorporated
LMR23630-Q1
www.ti.com.cn
ZHCSFR2B –DECEMBER 2016–REVISED MARCH 2018
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
The LMR23630-Q1 is a step-down DC-to-DC regulator. It is typically used to convert a higher DC voltage to a
lower DC voltage with a maximum output current of 3 A. The following design procedure can be used to select
components for the LMR23630-Q1. Alternately, the WEBENCH software may be used to generate complete
designs. When generating a design, the WEBENCH software utilizes iterative design procedure and accesses
comprehensive databases of components. See Custom Design With WEBENCH® Tools and ti.com for more
details.
9.2 Typical Applications
The LMR23630-Q1 only requires a few external components to convert from a wide voltage range supply to a
fixed output voltage. Figure 23 shows a basic schematic.
VIN 12 V
CBOOT
BOOT
SW
VIN
0.1 ꢀF
L
VOUT
5 V/3 A
CIN
10 ꢀF
10 ꢀH
EN/
SYNC
PAD
CFF
47 pF
RFBT
88.7 kΩ
COUT
100 ꢀF
FB
RFBB
22.1 kΩ
CVCC
2.2 ꢀF
VCC
PGND
AGND
Copyright © 2016, Texas Instruments Incorporated
Figure 23. Application Circuit
The external components have to fulfill the needs of the application, but also the stability criteria of the device
control loop. Table 2 can be used to simplify the output filter component selection.
Table 2. L, COUT and CFF Typical Values
fSW (kHz)
400
VOUT (V)
L (µH)(1)
COUT (µF)(2)
CFF (pF)
75
RFBT (kΩ)(3)
3.3
5
6.8
150
100
68
51
400
10
47
88.7
243
510
400
12
24
15
See note(4)
See note(4)
400
15
47
(1) Inductance value is calculated based on VIN = 36 V.
(2) All the COUT values are after derating. Add more when using ceramic capacitors.
(3) RFBT = 0 Ω for VOUT = 1 V. RFBB = 22.1 kΩ for all other VOUT setting.
(4) High ESR COUT gives enough phase boost, and CFF not needed.
Copyright © 2016–2018, Texas Instruments Incorporated
19
LMR23630-Q1
ZHCSFR2B –DECEMBER 2016–REVISED MARCH 2018
www.ti.com.cn
9.2.1 Design Requirements
Detailed design procedure is described based on a design example. For this design example, use the
parameters listed in Table 3 as the input parameters.
Table 3. Design Example Parameters
DESIGN PARAMETER
Input voltage, VIN
EXAMPLE VALUE
12 V typical, range from 8 V to 28 V
Output voltage, VOUT
5 V
3 A
Maximum output current IO_MAX
Transient Response 0.3 A to 3 A
Output voltage ripple
5%
50 mV
400 mV
400 kHz
Input voltage ripple
Switching frequency fSW
9.2.2 Detailed Design Procedure
9.2.2.1 Custom Design With WEBENCH® Tools
Click here to create a custom design using the LMR23630-Q1 device with the WEBENCH® Power Designer.
1. Start by entering the input voltage (VIN), output voltage (VOUT), and output current (IOUT) requirements.
2. Optimize the design for key parameters such as efficiency, footprint, and cost using the optimizer dial.
3. Compare the generated design with other possible solutions from Texas Instruments.
The WEBENCH Power Designer provides a customized schematic along with a list of materials with real-time
pricing and component availability.
In most cases, these actions are available:
•
•
•
•
Run electrical simulations to see important waveforms and circuit performance
Run thermal simulations to understand board thermal performance
Export customized schematic and layout into popular CAD formats
Print PDF reports for the design, and share the design with colleagues
Get more information about WEBENCH tools at www.ti.com/WEBENCH.
9.2.2.2 Output Voltage Setpoint
The output voltage of LMR23630-Q1 is externally adjustable using a resistor divider network. The divider network
is comprised of top feedback resistor RFBT and bottom feedback resistor RFBB. Equation 11 is used to determine
the output voltage:
VOUT - VREF
RFBT
=
ìRFBB
VREF
(11)
Choose the value of RFBB to be 22.1 kΩ. With the desired output voltage set to 5 V and the VREF = 1 V, the RFBB
value can then be calculated using Equation 11. The formula yields to a value 88.7 kΩ.
9.2.2.3 Switching Frequency
The default switching frequency of the LMR23630-Q1 is 400 kHz. For other required switching frequency, adjust
RT value or synchronize the device to an external clock to get the target frequency, refer to Adjustable Frequency
andEnable/Synchronization for more details.
20
Copyright © 2016–2018, Texas Instruments Incorporated
LMR23630-Q1
www.ti.com.cn
ZHCSFR2B –DECEMBER 2016–REVISED MARCH 2018
9.2.2.4 Inductor Selection
The most critical parameters for the inductor are the inductance, saturation current, and the rated current. The
inductance is based on the desired peak-to-peak ripple current ΔiL. Since the ripple current increases with the
input voltage, the maximum input voltage is always used to calculate the minimum inductance LMIN. Use
Equation 13 to calculate the minimum value of the output inductor. KIND is a coefficient that represents the
amount of inductor ripple current relative to the maximum output current of the device. A reasonable value of
KIND should be 20% to 40%. During an instantaneous short or over current operation event, the RMS and peak
inductor current can be high. The inductor current rating should be higher than the current limit of the device.
VOUT ì V
- VOUT
(
)
IN_MAX
DiL =
VIN_MAX ìL ì fSW
(12)
(13)
V
- VOUT
VOUT
IN_MAX
LMIN
=
ì
IOUT ìKIND
VIN_MAX ì fSW
In general, it is preferable to choose lower inductance in switching power supplies, because it usually
corresponds to faster transient response, smaller DCR, and reduced size for more compact designs. But too low
of an inductance can generate too large of an inductor current ripple such that over current protection at the full
load could be falsely triggered. It also generates more conduction loss and inductor core loss. Larger inductor
current ripple also implies larger output voltage ripple with same output capacitors. With peak-current-mode
control, TI recommends not to have an inductor current rippple that is too small. A larger peak current ripple
improves the comparator signal-to-noise ratio.
For this design example, choose KIND = 0.4, the minimum inductor value is calculated to be 8.56 µH. Choose the
nearest standard 8.2-μH ferrite inductor with a capability of 4-A RMS current and 6-A saturation current.
9.2.2.5 Output Capacitor Selection
Choose the output capacitor(s), COUT, with care since it directly affects the steady state output voltage ripple,
loop stability, and the voltage over/undershoot during load current transients.
The output ripple is essentially composed of two parts. One is caused by the inductor current ripple going
through the ESR of the output capacitors:
DVOUT_ESR = DiL ìESR = KIND ìIOUT ìESR
(14)
The other is caused by the inductor current ripple charging and discharging the output capacitors:
DiL
KIND ìIOUT
DVOUT _C
=
=
8ì f ìCOUT
8ì f ìCOUT
SW
SW
(15)
The two components in the voltage ripple are not in phase, so the actual peak-to-peak ripple is smaller than the
sum of two peaks.
Output capacitance is usually limited by transient performance specifications if the system requires tight voltage
regulation with presence of large current steps and fast slew rate. When a fast large load increase happens,
output capacitors provide the required charge before the inductor current can slew up to the appropriate level.
The regulator’s control loop usually needs four or more clock cycles to respond to the output voltage droop. The
output capacitance must be large enough to supply the current difference for four clock cycles to maintain the
output voltage within the specified range. Equation 16 shows the minimum output capacitance needed for
specified output undershoot. When a sudden large load decrease happens, the output capacitors absorb energy
stored in the inductor. which results in an output voltage overshoot. Equation 17 calculates the minimum
capacitance required to keep the voltage overshoot within a specified range.
Copyright © 2016–2018, Texas Instruments Incorporated
21
LMR23630-Q1
ZHCSFR2B –DECEMBER 2016–REVISED MARCH 2018
www.ti.com.cn
4ì IOH -IOL
(
)
COUT
>
fSW ì VUS
(16)
2
IOH2 -IOL
COUT
>
2
(VOUT + VOS)2 - VOUT
where
•
•
•
•
•
KIND = Ripple ratio of the inductor ripple current (ΔiL / IOUT
IOL = Low level output current during load transient
IOH = High level output current during load transient
VUS = Target output voltage undershoot
)
VOS = Target output voltage overshoot
(17)
For this design example, the target output ripple is 50 mV. Presuppose ΔVOUT_ESR = ΔVOUT_C = 50 mV, and
chose KIND = 0.4. Equation 14 yields ESR no larger than 41.7 mΩ and Equation 15 yields COUT no smaller than
7.5 μF. For the target over/undershoot range of this design, VUS = VOS = 5% × VOUT = 250 mV. The COUT can be
calculated to be no smaller than 108 μF and 28.5 μF by Equation 16 and Equation 17 respectively. Consider of
derating, one 47-μF, 16-V and one 100-μF, 10-V ceramic capacitor with 5-mΩ ESR are used in parallel.
9.2.2.6 Feed-Forward Capacitor
The LMR23630-Q1 is internally compensated. Depending on the VOUT and frequency fSW, if the output capacitor
COUT is dominated by low ESR (ceramic types) capacitors, it could result in low phase margin. To improve the
phase boost an external feed-forward capacitor CFF can be added in parallel with RFBT. CFF is chosen such that
phase margin is boosted at the crossover frequency without CFF. A simple estimation for the crossover frequency
(fX) without CFF is shown in Equation 18, assuming COUT has very small ESR, and COUT value is after derating.
8.32
fX
=
VOUT ìCOUT
(18)
Equation 19 for CFF was tested:
1
CFF
=
4pì fX ìRFBT
(19)
For designs with higher ESR, CFF is not needed when COUT has very high ESR and CFF calculated from
Equation 19 should be reduced with medium ESR. Table 2 can be used as a quick starting point.
For the application in this design example, a 47-pF, 50-V, COG capacitor is selected.
9.2.2.7 Input Capacitor Selection
The LMR23630-Q1 device requires high-frequency input decoupling capacitor(s) and a bulk input capacitor,
depending on the application. The typical recommended value for the high-frequency decoupling capacitor is 4.7
μF to 10 μF. TI recommends a high-quality ceramic capacitor type X5R or X7R with sufficiency voltage rating. To
compensate the derating of ceramic capacitors, a voltage rating of twice the maximum input voltage is
recommended. Additionally, some bulk capacitance can be required, especially if the LMR23630-Q1 circuit is not
located within approximately 5 cm from the input voltage source. This capacitor is used to provide damping to the
voltage spike due to the lead inductance of the cable or the trace. For this design, two 4.7-μF, 50-V, X7R ceramic
capacitors are used. Use 0.1-μF for high-frequency filtering and place it as close as possible to the device pins.
9.2.2.8 Bootstrap Capacitor Selection
Every LMR23630-Q1 design requires a bootstrap capacitor (CBOOT). The recommended capacitor is 0.1 μF and
rated 16 V or higher. The bootstrap capacitor is located between the SW pin and the BOOT pin. The bootstrap
capacitor must be a high-quality ceramic type with an X7R or X5R grade dielectric for temperature stability.
22
Copyright © 2016–2018, Texas Instruments Incorporated
LMR23630-Q1
www.ti.com.cn
ZHCSFR2B –DECEMBER 2016–REVISED MARCH 2018
9.2.2.9 VCC Capacitor Selection
The VCC pin is the output of an internal LDO for LMR23630-Q1. To insure stability of the device, place a
minimum of 2.2-μF, 16-V, X7R capacitor from this pin to ground.
9.2.2.10 UVLO Setpoint
The system UVLO is adjusted using the external voltage divider network of RENT and RENB. The UVLO has two
thresholds, one for power up when the input voltage is rising and one for power down or brownouts when the
input voltage is falling. Use Equation 20 to determine the VIN UVLO level.
RENT + RENB
V
= VENH ì
IN_RISING
RENB
(20)
The EN rising threshold (VENH) for LMR23630-Q1 is set to be 1.55 V (typical). Choose the value of RENB to be
287 kΩ to minimize input current from the supply. If the desired VIN UVLO level is at 6 V, then the value of RENT
can be calculated using Equation 21:
V
≈
’
IN_RISING
RENT
=
-1 ìR
∆
∆
÷
ENB
÷
VENH
«
◊
(21)
Equation 21 yields a value of 820 kΩ. The resulting falling UVLO threshold, equals 4.4 V, can be calculated by
Equation 22, where EN hysteresis (VEN_HYS) is 0.4 V (typical).
RENT + RENB
V
= VENH - VEN_HYS
(
ì
)
IN_FALLING
RENB
(22)
Copyright © 2016–2018, Texas Instruments Incorporated
23
LMR23630-Q1
ZHCSFR2B –DECEMBER 2016–REVISED MARCH 2018
www.ti.com.cn
9.2.3 Application Curves
Unless otherwise specified the following conditions apply: VIN = 12 V, fSW = 400 kHz, L = 8.2 µH, COUT = 150 µF, TA = 25 °C.
VOUT = 5 V
IOUT = 3 A
fSW = 400 kHz
VOUT = 5 V
IOUT = 150 mA
fSW = 400 kHz
Figure 24. CCM Mode
Figure 25. DCM Mode
VOUT = 5 V
IOUT = 0 mA
fSW = 400 kHz
VOUT = 5 V
IOUT = 0 mA
fSW = 400 kHz
Figure 26. PFM Mode
Figure 27. FPWM Mode
VIN = 12 V
VOUT = 5 V
IOUT = 2 A
VIN = 12 V
VOUT = 5 V
IOUT = 2 A
Figure 28. Start-Up by VIN
Figure 29. Start-Up by EN
24
Copyright © 2016–2018, Texas Instruments Incorporated
LMR23630-Q1
www.ti.com.cn
ZHCSFR2B –DECEMBER 2016–REVISED MARCH 2018
Unless otherwise specified the following conditions apply: VIN = 12 V, fSW = 400 kHz, L = 8.2 µH, COUT = 150 µF, TA = 25 °C.
VIN = 12 V
VOUT = 5 V
IOUT = 0.3 A to 3 A,
VIN = 7 V to 36 V,
VOUT = 5 V
IOUT = 3 A
100 mA / μs
2 V / μs
Figure 30. Load Transient
Figure 31. Line Transient
VOUT = 5 V
IOUT = 1 A to short
VOUT = 5 V
IOUT = short to 1 A
Figure 32. Short Protection
Figure 33. Short Recovery
Copyright © 2016–2018, Texas Instruments Incorporated
25
LMR23630-Q1
ZHCSFR2B –DECEMBER 2016–REVISED MARCH 2018
www.ti.com.cn
10 Power Supply Recommendations
The LMR23630-Q1 is designed to operate from an input voltage supply range between 4 V and 36 V. This input
supply must be able to withstand the maximum input current and maintain a stable voltage. The resistance of the
input supply rail must be low enough that an input current transient does not cause a high enough drop at the
LMR23630-Q1 supply voltage that can cause a false UVLO fault triggering and system reset. If the input supply
is located more than a few inches from the LMR23630-Q1, additional bulk capacitance may be required in
addition to the ceramic input capacitors. The amount of bulk capacitance is not critical, but a 47-μF or 100-μF
electrolytic capacitor is a typical choice.
11 Layout
11.1 Layout Guidelines
Layout is a critical portion of good power supply design. The following guidelines will help users design a PCB
with the best power conversion performance, thermal performance, and minimized generation of unwanted EMI.
1. The input bypass capacitor CIN must be placed as close as possible to the VIN and PGND pins. Grounding
for both the input and output capacitors must consist of localized top side planes that connect to the PGND
pin and PAD.
2. Place bypass capacitors for VCC close to the VCC pin and ground the bypass capacitor to device ground.
3. Minimize trace length to the FB pin net. Locate both feedback resistors, RFBT and RFBB close to the FB pin.
Place CFF directly in parallel with RFBT. If VOUT accuracy at the load is important, make sure VOUT sense is
made at the load. Route VOUT sense path away from noisy nodes and preferably through a layer on the other
side of a shielded layer.
4. Use ground plane in one of the middle layers as noise shielding and heat-dissipation path.
5. Have a single point ground connection to the plane. Route the ground connections for the feedback and
enable components to the ground plane. This prevents any switched or load currents from flowing in the
analog ground traces. If not properly handled, poor grounding can result in degraded load regulation or
erratic output voltage ripple behavior.
6. Make VIN, VOUT and ground bus connections as wide as possible. This reduces any voltage drops on the
input or output paths of the converter and maximizes efficiency.
7. Provide adequate device heat-sinking. Use an array of heat-sinking vias to connect the exposed pad to the
ground plane on the bottom PCB layer. If the PCB has multiple copper layers, these thermal vias can also be
connected to inner layer heat-spreading ground planes. Ensure enough copper area is used for heat sinking
to keep the junction temperature below 125°C.
11.1.1 Compact Layout for EMI Reduction
Radiated EMI is generated by the high di/dt components in pulsing currents in switching converters. The larger
area covered by the path of a pulsing current, the more EMI is generated. High frequency ceramic bypass
capacitors at the input side provide primary path for the high di/dt components of the pulsing current. Placing
ceramic bypass capacitor(s) as close as possible to the VIN and PGND pins is the key to EMI reduction.
The SW pin connecting to the inductor must be as short as possible, and just wide enough to carry the load
current without excessive heating. Use short, thick traces or copper pours (shapes) for high current conduction
path to minimize parasitic resistance. The output capacitors must be placed close to the VOUT end of the inductor
and closely grounded to PGND pin and exposed PAD.
Place the bypass capacitors on VCC as close as possible to the pin and closely grounded to PGND and the
exposed PAD.
26
Copyright © 2016–2018, Texas Instruments Incorporated
LMR23630-Q1
www.ti.com.cn
ZHCSFR2B –DECEMBER 2016–REVISED MARCH 2018
Layout Guidelines (continued)
11.1.2 Ground Plane and Thermal Considerations
It is recommended to use one of the middle layers as a solid ground plane. Ground plane provides shielding for
sensitive circuits and traces. It also provides a quiet reference potential for the control circuitry. Connect the
AGND and PGND pins to the ground plane using vias right next to the bypass capacitors. PGND pin is
connected to the source of the internal LS switch. They must be connected directly to the grounds of the input
and output capacitors. The PGND net contains noise at switching frequency and may bounce due to load
variations. PGND trace, as well as VIN and SW traces, must be constrained to one side of the ground plane. The
other side of the ground plane contains much less noise and should be used for sensitive routes.
It is recommended to provide adequate device heat sinking by utilizing the PAD of the IC as the primary thermal
path. Use a minimum 4 by 2 array of 12 mil thermal vias to connect the PAD to the system ground plane heat
sink. The vias must be evenly distributed under the PAD. Use as much copper as possible, for system ground
plane, on the top and bottom layers for the best heat dissipation. Use a four-layer board with the copper
thickness for the four layers, starting from the top of, 2 oz / 1 oz / 1 oz / 2 oz. Four layer boards with enough
copper thickness provides low current conduction impedance, proper shielding and lower thermal resistance.
The thermal characteristics of the LMR23630-Q1 are specified using the parameter RθJA, which characterize the
junction temperature of silicon to the ambient temperature in a specific system. Although the value of RθJA is
dependent on many variables, it still can be used to approximate the operating junction temperature of the
device. To obtain an estimate of the device junction temperature, one may use Equation 23:
TJ = PD × RθJA + TA
where
•
•
•
•
•
TJ = Junction temperature in °C
PD = VIN × IIN × (1 – Efficiency) – 1.1 x IOUT2 × DCR in Watt
DCR = Inductor DC parasitic resistance in Ω
RθJA = Junction to ambient thermal resistance of the device in °C/W
TA = Ambient temperature in °C
(23)
The maximum operating junction temperature of the LMR23630-Q1 is 125°C. RθJA is highly related to PCB size
and layout, as well as environmental factors such as heat sinking and air flow.
11.1.3 Feedback Resistors
To reduce noise sensitivity of the output voltage feedback path, it is important to place the resistor divider and
CFF close to the FB pin, rather than close to the load. The FB pin is the input to the error amplifier, so it is a high
impedance node and very sensitive to noise. Placing the resistor divider and CFF closer to the FB pin reduces the
trace length of FB signal and reduces noise coupling. The output node is a low impedance node, so the trace
from VOUT to the resistor divider can be long if short path is not available.
If voltage accuracy at the load is important, make sure voltage sense is made at the load. Doing so corrects for
voltage drops along the traces and provide the best output accuracy. Route the voltage sense trace from the
load to the feedback resistor divider away from the SW node path and the inductor to avoid contaminating the
feedback signal with switch noise, while also minimizing the trace length. This is most important when high value
resistors are used to set the output voltage. TI recommends routing the voltage sense trace and place the
resistor divider on a different layer than the inductor and SW node path, such that there is a ground plane in
between the feedback trace and inductor/SW node polygon. This provides further shielding for the voltage
feedback path from EMI noises.
Copyright © 2016–2018, Texas Instruments Incorporated
27
LMR23630-Q1
ZHCSFR2B –DECEMBER 2016–REVISED MARCH 2018
www.ti.com.cn
11.2 Layout Examples
Output Bypass
Capacitor
Output Inductor
Input Bypass
Capacitor
SW
PGND
VIN
BOOT Capacitor
BOOT
VCC
FB
AGND
VCC
Capacitor
EN/
SYNC
UVLO Adjust Resistor
Output Voltage Set
Resistor
Thermal VIA
VIA (Connect to GND Plane)
Figure 34. SOIC Layout
Output
Inductor
Output Bypass
Capacitor
PGND
NC
SW
SW
Input Bypass
Capacitor
BOOT
Capacitor
BOOT
VCC
FB
VIN
VIN
VCC
Capacitor
EN/SYNC
AGND
UVLO Adjust
Resistor
RT
RT
Thermal VIA
Output Voltage
Set Resistor
VIA (Connect to GND Plane)
Figure 35. WSON Layout
28
版权 © 2016–2018, Texas Instruments Incorporated
LMR23630-Q1
www.ti.com.cn
ZHCSFR2B –DECEMBER 2016–REVISED MARCH 2018
12 器件和文档支持
12.1 使用 WEBENCH® 工具创建定制设计
请单击此处,结合 LMR23630-Q1 器件和 WEBENCH® 电源设计器创建定制设计。
1. 首先键入输入电压 (VIN)、输出电压 (VOUT) 和输出电流 (IOUT) 要求。
2. 使用优化器拨盘优化关键参数设计,如效率、封装和成本。
3. 将生成的设计与德州仪器 (TI) 的其他解决方案进行比较。
WEBENCH 电源设计器可提供定制原理图以及罗列实时价格和组件供货情况的物料清单。
在多数情况下,可执行以下操作:
•
•
•
•
运行电气仿真,观察重要波形以及电路性能
运行热性能仿真,了解电路板热性能
将定制原理图和布局方案导出至常用 CAD 格式
打印设计方案的 PDF 报告并与同事共享
有关 WEBENCH 工具的详细信息,请访问 www.ti.com/WEBENCH。
12.2 接收文档更新通知
要接收文档更新通知,请导航至 TI.com.cn 上的器件产品文件夹。请单击右上角的提醒我 进行注册,即可每周接收
产品信息更改摘要。有关更改的详细信息,请查看任何已修订文档中包含的修订历史记录。
12.3 社区资源
下列链接提供到 TI 社区资源的连接。链接的内容由各个分销商“按照原样”提供。这些内容并不构成 TI 技术规范,
并且不一定反映 TI 的观点;请参阅 TI 的 《使用条款》。
TI E2E™ 在线社区 TI 的工程师对工程师 (E2E) 社区。此社区的创建目的在于促进工程师之间的协作。在
e2e.ti.com 中,您可以咨询问题、分享知识、拓展思路并与同行工程师一道帮助解决问题。
设计支持
TI 参考设计支持 可帮助您快速查找有帮助的 E2E 论坛、设计支持工具以及技术支持的联系信息。
12.4 商标
PowerPAD, E2E are trademarks of Texas Instruments.
WEBENCH, SIMPLE SWITCHER are registered trademarks of Texas Instruments.
All other trademarks are the property of their respective owners.
12.5 静电放电警告
这些装置包含有限的内置 ESD 保护。 存储或装卸时,应将导线一起截短或将装置放置于导电泡棉中,以防止 MOS 门极遭受静电损
伤。
12.6 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 机械、封装和可订购信息
以下页面包含机械、封装和可订购信息。这些信息是指定器件的最新可用数据。数据如有变更,恕不另行通知,且
不会对此文档进行修订。如需获取此数据表的浏览器版本,请查阅左侧的导航栏。
版权 © 2016–2018, Texas Instruments Incorporated
29
PACKAGE OPTION ADDENDUM
www.ti.com
23-Jun-2023
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
LMR23630AFQDDAQ1
LMR23630AFQDDARQ1
LMR23630APQDRRRQ1
LMR23630APQDRRTQ1
LMR23630AQDDAQ1
LMR23630AQDDARQ1
LMR23630FQDRRRQ1
LMR23630FQDRRTQ1
LMR23630QDRRRQ1
LMR23630QDRRTQ1
ACTIVE SO PowerPAD
ACTIVE SO PowerPAD
DDA
DDA
DRR
DRR
DDA
DDA
DRR
DRR
DRR
DRR
8
8
75
RoHS & Green
NIPDAUAG
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
F30AFQ
Samples
Samples
Samples
Samples
Samples
Samples
Samples
Samples
Samples
Samples
2500 RoHS & Green
3000 RoHS & Green
NIPDAUAG
F30AFQ
363PQ
363PQ
F30AQ
F30AQ
363FQ
363FQ
3630Q
3630Q
ACTIVE
ACTIVE
WSON
WSON
12
12
8
SN
SN
250
75
RoHS & Green
RoHS & Green
ACTIVE SO PowerPAD
ACTIVE SO PowerPAD
NIPDAUAG
NIPDAUAG
SN
8
2500 RoHS & Green
3000 RoHS & Green
ACTIVE
ACTIVE
ACTIVE
ACTIVE
WSON
WSON
WSON
WSON
12
12
12
12
250
3000 RoHS & Green
250 RoHS & Green
RoHS & Green
SN
SN
SN
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
23-Jun-2023
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF LMR23630-Q1 :
Catalog : LMR23630
•
NOTE: Qualified Version Definitions:
Catalog - TI's standard catalog product
•
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Jun-2023
TAPE AND REEL INFORMATION
REEL DIMENSIONS
TAPE DIMENSIONS
K0
P1
W
B0
Reel
Diameter
Cavity
A0
A0 Dimension designed to accommodate the component width
B0 Dimension designed to accommodate the component length
K0 Dimension designed to accommodate the component thickness
Overall width of the carrier tape
W
P1 Pitch between successive cavity centers
Reel Width (W1)
QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE
Sprocket Holes
Q1 Q2
Q3 Q4
Q1 Q2
Q3 Q4
User Direction of Feed
Pocket Quadrants
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LMR23630AFQDDARQ1
SO
DDA
8
2500
330.0
12.8
6.4
5.2
2.1
8.0
12.0
Q1
PowerPAD
LMR23630APQDRRRQ1 WSON
LMR23630APQDRRTQ1 WSON
DRR
DRR
DDA
12
12
8
3000
250
330.0
180.0
330.0
12.4
12.4
12.8
3.3
3.3
6.4
3.3
3.3
5.2
1.0
1.0
2.1
8.0
8.0
8.0
12.0
12.0
12.0
Q2
Q2
Q1
LMR23630AQDDARQ1
SO
2500
PowerPAD
LMR23630FQDRRRQ1
LMR23630FQDRRTQ1
LMR23630QDRRRQ1
LMR23630QDRRTQ1
WSON
WSON
WSON
WSON
DRR
DRR
DRR
DRR
12
12
12
12
3000
250
330.0
180.0
330.0
180.0
12.4
12.4
12.4
12.4
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
1.0
1.0
1.0
1.0
8.0
8.0
8.0
8.0
12.0
12.0
12.0
12.0
Q2
Q2
Q2
Q2
3000
250
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Jun-2023
TAPE AND REEL BOX DIMENSIONS
Width (mm)
H
W
L
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
LMR23630AFQDDARQ1
LMR23630APQDRRRQ1
LMR23630APQDRRTQ1
LMR23630AQDDARQ1
LMR23630FQDRRRQ1
LMR23630FQDRRTQ1
LMR23630QDRRRQ1
LMR23630QDRRTQ1
SO PowerPAD
WSON
DDA
DRR
DRR
DDA
DRR
DRR
DRR
DRR
8
2500
3000
250
366.0
367.0
213.0
366.0
367.0
213.0
367.0
213.0
364.0
367.0
191.0
364.0
367.0
191.0
367.0
191.0
50.0
38.0
35.0
50.0
38.0
35.0
38.0
35.0
12
12
8
WSON
SO PowerPAD
WSON
2500
3000
250
12
12
12
12
WSON
WSON
3000
250
WSON
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Jun-2023
TUBE
T - Tube
height
L - Tube length
W - Tube
width
B - Alignment groove width
*All dimensions are nominal
Device
Package Name Package Type
Pins
SPQ
L (mm)
W (mm)
T (µm)
B (mm)
LMR23630AFQDDAQ1
LMR23630AQDDAQ1
DDA
DDA
HSOIC
HSOIC
8
8
75
75
517
517
7.87
7.87
635
635
4.25
4.25
Pack Materials-Page 3
PACKAGE OUTLINE
DRR0012D
WSON - 0.8 mm max height
SCALE 4.000
PLASTIC SMALL OUTLINE - NO LEAD
3.1
2.9
B
A
PIN 1 INDEX AREA
3.1
2.9
0.1 MIN
(0.05)
S
C
A
L
E
3
0
.
A
SECTION A-A
TYPICAL
0.8
0.7
C
SEATING PLANE
0.08 C
0.05
0.00
EXPOSED
THERMAL PAD
(0.2) TYP
1.7 0.1
6
7
A
A
13
2X
2.5
2.5 0.1
1
12
10X 0.5
0.3
0.2
12X
0.38
0.28
12X
PIN 1 ID
0.1
C A B
C
(OPTIONAL)
0.05
4223146/D 10/2018
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. The package thermal pad must be soldered to the printed circuit board for thermal and mechanical performance.
www.ti.com
EXAMPLE BOARD LAYOUT
DRR0012D
WSON - 0.8 mm max height
PLASTIC SMALL OUTLINE - NO LEAD
(1.7)
12X (0.53)
SYMM
1
12
12X (0.25)
13
SYMM
(2.5)
10X (0.5)
(1)
(R0.05) TYP
6
7
(0.6)
(2.87)
(
0.2) VIA
TYP
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:20X
0.07 MIN
ALL AROUND
0.07 MAX
ALL AROUND
EXPOSED METAL
EXPOSED METAL
SOLDER MASK
OPENING
METAL EDGE
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
NON SOLDER MASK
DEFINED
SOLDER MASK
DEFINED
(PREFERRED)
SOLDER MASK DETAILS
4223146/D 10/2018
NOTES: (continued)
4. This package is designed to be soldered to a thermal pad on the board. For more information, see Texas Instruments literature
number SLUA271 (www.ti.com/lit/slua271).
5. Vias are optional depending on application, refer to device data sheet. If any vias are implemented, refer to their locations shown
on this view. It is recommended that vias under paste be filled, plugged or tented.
www.ti.com
EXAMPLE STENCIL DESIGN
DRR0012D
WSON - 0.8 mm max height
PLASTIC SMALL OUTLINE - NO LEAD
SYMM
(0.47)
12X (0.53)
1
12
12X (0.25)
METAL
TYP
(0.675)
SYMM
13
10X (0.5)
(1.15)
(R0.05) TYP
6
7
(0.74)
(2.87)
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
EXPOSED PAD
80.1% PRINTED SOLDER COVERAGE BY AREA
SCALE:25X
4223146/D 10/2018
NOTES: (continued)
6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
www.ti.com
重要声明和免责声明
TI“按原样”提供技术和可靠性数据(包括数据表)、设计资源(包括参考设计)、应用或其他设计建议、网络工具、安全信息和其他资源,
不保证没有瑕疵且不做出任何明示或暗示的担保,包括但不限于对适销性、某特定用途方面的适用性或不侵犯任何第三方知识产权的暗示担
保。
这些资源可供使用 TI 产品进行设计的熟练开发人员使用。您将自行承担以下全部责任:(1) 针对您的应用选择合适的 TI 产品,(2) 设计、验
证并测试您的应用,(3) 确保您的应用满足相应标准以及任何其他功能安全、信息安全、监管或其他要求。
这些资源如有变更,恕不另行通知。TI 授权您仅可将这些资源用于研发本资源所述的 TI 产品的应用。严禁对这些资源进行其他复制或展示。
您无权使用任何其他 TI 知识产权或任何第三方知识产权。您应全额赔偿因在这些资源的使用中对 TI 及其代表造成的任何索赔、损害、成
本、损失和债务,TI 对此概不负责。
TI 提供的产品受 TI 的销售条款或 ti.com 上其他适用条款/TI 产品随附的其他适用条款的约束。TI 提供这些资源并不会扩展或以其他方式更改
TI 针对 TI 产品发布的适用的担保或担保免责声明。
TI 反对并拒绝您可能提出的任何其他或不同的条款。IMPORTANT NOTICE
邮寄地址:Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023,德州仪器 (TI) 公司
相关型号:
©2020 ICPDF网 联系我们和版权申明