LMV7219M7/NOPB [TI]
具有轨到轨输出的 7 nsec、2.7V 至 5V 比较器 | DCK | 5 | -40 to 85;型号: | LMV7219M7/NOPB |
厂家: | TEXAS INSTRUMENTS |
描述: | 具有轨到轨输出的 7 nsec、2.7V 至 5V 比较器 | DCK | 5 | -40 to 85 放大器 光电二极管 比较器 |
文件: | 总29页 (文件大小:2005K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Support &
Community
Product
Folder
Order
Now
Tools &
Software
Technical
Documents
LMV7219
SNOS458I –APRIL 2000–REVISED JUNE 2016
LMV7219 7-ns 2.7-V to 5-V Comparator with Rail-to-Rail Output
1 Features
3 Description
The LMV7219 is a low-power, high-speed comparator
with internal hysteresis. The LMV7219 operating
voltage ranges from 2.7 V to 5 V with push-pull rail-
to-rail output. This device achieves
1
•
(VS = 5 V, TA = 25°C, Typical Values Unless
Specified)
•
•
•
Propagation Delay 7 ns
a
7-ns
Low Supply Current 1.1 mA
propagation delay while consuming only 1.1 mA of
supply current at 5 V.
Input Common Mode Voltage Range Extends
200 mv Below Ground
The LMV7219 inputs have a common mode voltage
range that extends 200 mV below ground, allowing
ground sensing. The internal hysteresis ensures
clean output transitions even with slow-moving inputs
signals.
•
•
•
•
Ideal for 2.7-V and 5-V Single Supply Applications
Internal Hysteresis Ensures Clean Switching
Fast Rise and Fall Time 1.3 ns
Available in Space-saving Packages: SC-70 and
SOT-23
The LMV7219 is available in the SC-70 and SOT-23
packages, which are ideal for systems where small
size and low power are critical.
•
Supports 105°C PCB Temperature
Device Information(1)
2 Applications
PART NUMBER
PACKAGE
SC-70 (5)
SOT-23 (5)
BODY SIZE (NOM)
2.00 mm × 1.25 mm
2.88 mm × 1.60 mm
•
•
•
•
•
•
•
Portable and Battery-powered Systems
Scanners
LMV7219
Set Top Boxes
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
High Speed Differential Line Receiver
Window Comparators
Zero-crossing Detectors
High-speed Sampling Circuits
Typical Application
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LMV7219
SNOS458I –APRIL 2000–REVISED JUNE 2016
www.ti.com
Table of Contents
7.3 Feature Description................................................. 11
7.4 Device Functional Modes........................................ 11
Application and Implementation ........................ 12
8.1 Application Information............................................ 12
8.2 Typical Application ................................................. 12
Power Supply Recommendations...................... 16
1
2
3
4
5
6
Features.................................................................. 1
Applications ........................................................... 1
Description ............................................................. 1
Revision History..................................................... 2
Pin Configuration and Functions......................... 3
Specifications......................................................... 4
6.1 Absolute Maximum Ratings ...................................... 4
6.2 ESD Ratings.............................................................. 4
6.3 Recommended Operating Conditions....................... 4
6.4 Thermal Information ................................................. 4
6.5 Electrical Characteristics 2.7 V ................................ 5
6.6 Electrical Characteristics 5 V ................................... 6
6.7 Typical Performance Characteristics ........................ 8
Detailed Description ............................................ 11
7.1 Overview ................................................................. 11
7.2 Functional Block Diagram ....................................... 11
8
9
10 Layout................................................................... 16
10.1 Layout Guidelines ................................................. 16
10.2 Layout Example .................................................... 17
11 Device and Documentation Support ................. 18
11.1 Documentation Support ........................................ 18
11.2 Receiving Notification of Documentation Updates 18
11.3 Community Resources.......................................... 18
11.4 Trademarks........................................................... 18
11.5 Electrostatic Discharge Caution............................ 18
7
12 Mechanical, Packaging, and Orderable
Information ........................................................... 18
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision H (April 2016) to Revision I
Page
•
•
•
•
•
Added Supports 105°C PCB Temperature to Features List................................................................................................... 1
Changed Operating Temperature to Ambient Temperature .................................................................................................. 4
Added Junction Temperature of 125 °C................................................................................................................................. 4
Added PCB Temperature of 105 °C ...................................................................................................................................... 4
Added TPCB ≤ 105°C throughout Electrical Tables ................................................................................................................ 5
Changes from Revision G (January 2015) to Revision H
Page
•
•
Changed "Infrared or Convection (20 sec)" from 235 °C ....................................................................................................... 4
Added thermal data for SOT23 and SC70 packages ............................................................................................................ 4
Changes from Revision F (April 2013) to Revision G
Page
•
Added, updated, or renamed the following sections: Device Information Table, Pin Configurations and Functions;
Specifications; Application and Implementation; Power Supply Recommendations; Layout; Device and
Documentation Support; Mechanical, Packaging, and Ordering Information ........................................................................ 1
•
Changed from "transient response" to "eliminate possible output chatter" in Circuit Layout and Bypassing ..................... 16
Changes from Revision E (March 2013) to Revision F
Page
•
Changed layout of National Data Sheet to TI format ............................................................................................................. 1
2
Submit Documentation Feedback
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: LMV7219
LMV7219
www.ti.com
SNOS458I –APRIL 2000–REVISED JUNE 2016
5 Pin Configuration and Functions
5-Pin SC-70 and SOT-23
Packages DCK and DBV
(Top View)
Pin Functions
PIN
I/O
DESCRIPTION
NUMBER
NAME
OUT
V-
1
2
3
4
5
O
I
Output
Negative Supply
Non-inverting input
Inverting input
+IN
I
-IN
I
V+
I
Positive Supply
Copyright © 2000–2016, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LMV7219
LMV7219
SNOS458I –APRIL 2000–REVISED JUNE 2016
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)
(1)(2)
MIN
MAX
± Supply Voltage
See(3)
UNIT
Differential input voltage
Output short circuit duration
Supply voltage (V+ - V−)
5.5
V
Infrared or Convection (20 sec)
Soldering information
260
°C
°C
Wave Soldering (10 sec)
260 (lead temp)
(V+) + 0.4
Voltage at input/output pins
V
(V−) − 0.4
Current at input pin(4)
±10
150
150
mA
°C
Maximum junction temperature
Storage temperature
−65
°C
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is intended to be functional, but specific performance is not ensured. For ensured specifications and the test
conditions, see the Electrical characteristics.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
(3) Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in
exceeding the maximum allowed junction temperature of 150°C. Output currents in excess of ±30mA over long term may adversely
affect reliability.
(4) Limiting input pin current is only necessary for input voltages that exceed absolute maximum input voltage ratings.
6.2 ESD Ratings
VALUE
±2000
±150
UNIT
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1)
Charged-device model (CDM), per JEDEC specification JESD22-C101(2)
Electrostatic
discharge
V(ESD)
V
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. Manufacturing with
less than 500-V HBM is possible with the necessary precautions. Pins listed as ±2000 V may actually have higher performance.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process. Manufacturing with
less than 250-V CDM is possible with the necessary precautions. Pins listed as ±150 V may actually have higher performance.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
2.7
MAX
5
UNIT
V
Supply voltages (V+ - V−)
Ambient Temperature(1)
Junction Temperature
PCB Temperature
−40
+85
125
105
°C
°C
°C
(1) The maximum power dissipation is a function of TJ(MAX), RθJA, and TA. The maximum allowable power dissipation at any ambient
temperature is PD = (TJ(MAX) - TA)/RθJA. All numbers apply for packages soldered directly into a PC board.
6.4 Thermal Information
LMV7219
LMV7219
DCK (SC70)
5 PINS
296
THERMAL METRIC(1)
DBV (SOT23)
UNIT
5 PINS
209
170
68
RθJA
Junction-to-ambient thermal resistance
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
Junction-to-top characterization parameter
°C/W
°C/W
°C/W
°C/W
RθJC(top)
RθJB
132
76
ψJT
52
8.6
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
4
Submit Documentation Feedback
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: LMV7219
LMV7219
www.ti.com
SNOS458I –APRIL 2000–REVISED JUNE 2016
Thermal Information (continued)
LMV7219
LMV7219
DCK (SC70)
5 PINS
75
THERMAL METRIC(1)
DBV (SOT23)
UNIT
5 PINS
68
ψJB
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
°C/W
°C/W
RθJC(bot)
N/A
N/A
6.5 Electrical Characteristics 2.7 V
Unless otherwise specified, all limits ensured for TJ = 25°C, VCM = V+/2, V+ = 2.7 V, V− = 0 V, CL = 10 pF and RL > 1MΩ to V−.
PARAMETER
TEST CONDITIONS
MIN
TYP(1)
MAX(2) UNIT
1
6
VOS
Input offset voltage
mV
8
−40°C ≤ TJ ≤ +85°C and TPCB ≤ 105°C
−40°C ≤ TJ ≤ +85°C and TPCB ≤ 105°C
−40°C ≤ TJ ≤ +85°C and TPCB ≤ 105°C
450
50
950
nA
IB
Input bias current
Input offset current
2000
200
nA
IOS
400
62
55
85
CMRR Common mode rejection ratio
0 V < VCM < 1.50 V
V+ = 2.7 V to 5 V
dB
dB
−40°C ≤ TJ ≤ +85°C
and TPCB ≤ 105°C
65
85
PSRR
Power supply rejection ratio
Input common-voltage range
−40°C ≤ TJ ≤ +85°C
and TPCB ≤ 105°C
55
V
CC −1.2
CC −1.3
V
CC −1
−40°C ≤ TJ ≤ +85°C
and TPCB ≤ 105°C
V
VCM
CMRR > 50 dB
V
−0.2
−0.1
−40°C ≤ TJ ≤ +85°C
and TPCB ≤ 105°C
0
V
CC −0.3
CC −0.4
V
CC −0.22
CC −0.02
130
IL = 4 mA,
VID = 500 mV
−40°C ≤ TJ ≤ +85°C
and TPCB ≤ 105°C
V
Output swing high
V
V
CC −0.05
CC −0.15
V
IL = 0.4 mA,
VID = 500 mV
−40°C ≤ TJ ≤ +85°C
and TPCB ≤ 105°C
V
VO
200
300
IL = −4 mA,
VID = −500 mV
−40°C ≤ TJ ≤ +85°C
and TPCB ≤ 105°C
Output swing low
mV
50
15
IL = −0.4 mA,
VID = −500 mV
−40°C ≤ TJ ≤ +85°C
and TPCB ≤ 105°C
150
Sourcing, VO = 0 V(3)
Sinking, VO = 2.7 V(3)
20
20
ISC
Output short circuit current
mA
1.6
0.9
IS
Supply current
No Load
See(4)
mA
2.2
−40°C ≤ TJ ≤ +85°C
and TPCB ≤ 105°C
VHYST
Input hysteresis voltage
7
3
mV
+
VTRIP
Input referred positive trip point (see Figure 19)
8
mV
(1) Typical Values represent the most likely parametric norm.
(2) All limits are specified by testing or statistical analysis.
(3) Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in
exceeding the maximum allowed junction temperature of 150°C. Output currents in excess of ±30mA over long term may adversely
affect reliability.
(4) The LMV7219 comparator has internal hysteresis. The trip points are the input voltage needed to change the output state in each
+
−
direction. The offset voltage is defined as the average of Vtrip and Vtrip , while the hysteresis voltage is the difference of these two.
Copyright © 2000–2016, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: LMV7219
LMV7219
SNOS458I –APRIL 2000–REVISED JUNE 2016
www.ti.com
Electrical Characteristics 2.7 V (continued)
Unless otherwise specified, all limits ensured for TJ = 25°C, VCM = V+/2, V+ = 2.7 V, V− = 0 V, CL = 10 pF and RL > 1MΩ to V−.
PARAMETER
Input referred negative trip point (see Figure 19)
Overdrive = 5 mV, VCM = 0V(5)
TEST CONDITIONS
MIN
TYP(1)
−4
12
MAX(2) UNIT
−
VTRIP
−8
mV
tPD
Propagation delay
Overdrive = 15 mV, VCM = 0 V(5)
Overdrive = 50 mV, VCM = 0 V(5)
See(6)
11
ns
10
20
ns
ns
ns
tSKEW
Propagation delay skew
Output rise time
1
tr
tf
10% to 90%
2.5
2
Output fall time
90% to 10%
(5) Propagation delay measurements made with 100 mV steps. Overdrive is measured relative to VTrip
.
(6) Propagation Delay Skew is defined as absolute value of the difference between tPDLH and tPDHL
.
6.6 Electrical Characteristics 5 V
Unless otherwise specified, all limits ensured for TJ = 25°C, VCM = V+/2, V+ = 5 V, V− = 0 V, CL = 10 pF and RL > 1 MΩ to V−.
PARAMETER
TEST CONDITIONS
MIN
TYP(1)
MAX(2) UNIT
1
6
VOS
Input offset voltage
mV
8
−40°C ≤ TJ ≤ +85°C and TPCB ≤ 105°C
−40°C ≤ TJ ≤ +85°C and TPCB ≤ 105°C
−40°C ≤ TJ ≤ +85°C and TPCB ≤ 105°C
500
50
950
nA
IB
Input bias current
Input offset current
2000
200
nA
IOS
400
65
55
85
CMRR Common mode rejection ratio
0 V < VCM < 3.8 V
V+ = 2.7 V to 5 V
dB
dB
−40°C ≤ TJ ≤ +85°C
and TPCB ≤ 105°C
65
85
PSRR
Power supply rejection ratio
−40°C ≤ TJ ≤ +85°C
and TPCB ≤ 105°C
55
V
CC −1.2
CC −1.3
VCC −1
V
−40°C ≤ TJ ≤ +85°C
and TPCB ≤ 105°C
V
Input common-mode voltage
range
VCM
CMRR > 50 dB
−0.2
−0.1
V
0
−40°C ≤ TJ ≤ +85°C
and TPCB ≤ 105°C
V
CC −0.2
CC −0.3
V
CC −0.13
CC −0.02
80
IL = 4 mA,
VID = 500 mV
−40°C ≤ TJ ≤ +85°C
and TPCB ≤ 105°C
V
Output swing high
Output swing low
V
V
CC −0.05
CC −0.15
V
IL = 0.4 mA,
VID = 500 mV
−40°C ≤ TJ ≤ +85°C
and TPCB ≤ 105°C
V
VO
180
280
IL = −4 mA,
VID = −500 mV
−40°C ≤ TJ ≤ +85°C
and TPCB ≤ 105°C
mV
50
10
IL = −0.4 mA,
VID = −500 mV
−40°C ≤ TJ ≤ +85°C
and TPCB ≤ 105°C
150
(1) Typical Values represent the most likely parametric norm.
(2) All limits are specified by testing or statistical analysis.
6
Submit Documentation Feedback
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: LMV7219
LMV7219
www.ti.com
SNOS458I –APRIL 2000–REVISED JUNE 2016
Electrical Characteristics 5 V (continued)
Unless otherwise specified, all limits ensured for TJ = 25°C, VCM = V+/2, V+ = 5 V, V− = 0 V, CL = 10 pF and RL > 1 MΩ to V−.
PARAMETER
TEST CONDITIONS
MIN
TYP(1)
MAX(2) UNIT
30
68
Sourcing, VO = 0 V(3)
Sinking, VO = 5 V(3)
−40°C ≤ TJ ≤ +85°C
and TPCB ≤ 105°C
20
30
20
ISC
Output short circuit current
mA
65
−40°C ≤ TJ ≤ +85°C
and TPCB ≤ 105°C
1.1
1.8
IS
Supply current
No Load
See(4)
mA
2.4
−40°C ≤ TJ ≤ +85°C
and TPCB ≤ 105°C
VHYST
Input hysteresis voltage
7.5
3.5
mV
+
VTrip
Input referred positive trip point (See Figure 19)
8
mV
Input referred negative trip
(See Figure 19)
point
−
VTrip
−8
−4
mV
Overdrive = 5 mV, VCM = 0 V(5)
Overdrive = 15 mV, VCM = 0 V(5)
Overdrive = 50 mV, VCM = 0 V(5)
See(6)
9
8
tPD
Propagation delay
20
19
ns
7
tSKEW
Propagation delay skew
Output rise time
0.4
1.3
1.25
ns
ns
ns
tr
tf
10% to 90%
Output fall time
90% to 10%
(3) Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in
exceeding the maximum allowed junction temperature of 150°C. Output currents in excess of ±30mA over long term may adversely
affect reliability.
(4) The LMV7219 comparator has internal hysteresis. The trip points are the input voltage needed to change the output state in each
+
−
direction. The offset voltage is defined as the average of Vtrip and Vtrip , while the hysteresis voltage is the difference of these two.
(5) Propagation delay measurements made with 100 mV steps. Overdrive is measured relative to VTrip
.
(6) Propagation Delay Skew is defined as absolute value of the difference between tPDLH and tPDHL
.
Copyright © 2000–2016, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: LMV7219
LMV7219
SNOS458I –APRIL 2000–REVISED JUNE 2016
www.ti.com
6.7 Typical Performance Characteristics
Unless otherwise specified, VS = 5 V, CL = 10 pF, TA = 25°C
Figure 1. Supply Current vs. Supply Voltage
Figure 2. VOS vs. Supply Voltage
VS = 2.7 V
Figure 4. Sourcing Current vs. Output Voltage
Figure 3. Input Offset and Trip Voltage vs. Supply Voltage
VS = 5 V
VS = 2.7 V
Figure 5. Sourcing Current vs. Output Voltage
Figure 6. Sinking Current vs. Output Voltage
8
Submit Documentation Feedback
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: LMV7219
LMV7219
www.ti.com
SNOS458I –APRIL 2000–REVISED JUNE 2016
Typical Performance Characteristics (continued)
Unless otherwise specified, VS = 5 V, CL = 10 pF, TA = 25°C
VS = 2.7 V
VS = 5 V
VOD = 15 mV
Figure 8. Propagation Delay vs. Temperature
Figure 7. Sinking Current vs. Output Voltage
VS = 5V
VS = 5 V
VOD = 15 mV
VOD = 15 mV
Figure 9. Propagation Delay vs. Temperature
Figure 10. Propagation Delay vs. Capacitive Load
VS = 2.7 V
CL = 10 pF
VOD = 15 mV
−
Figure 12. Propagation Delay (tPD
)
Figure 11. Propagation Delay vs. Input Overdrive
Copyright © 2000–2016, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: LMV7219
LMV7219
SNOS458I –APRIL 2000–REVISED JUNE 2016
www.ti.com
Typical Performance Characteristics (continued)
Unless otherwise specified, VS = 5 V, CL = 10 pF, TA = 25°C
VS = 2.7 V
CL = 10 pF
VOD = 15 mV
+
Figure 13. Propagation Delay (tPD
)
10
Submit Documentation Feedback
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: LMV7219
LMV7219
www.ti.com
SNOS458I –APRIL 2000–REVISED JUNE 2016
7 Detailed Description
7.1 Overview
LMV7219 is a single supply comparator with internal hysteresis, 7 ns of propagation delay and only 1.1 mA of
supply current.
The LMV7219 has a typical input common mode voltage range of −0.2 V below the ground to 1 V below Vcc. The
differential input stage is a pair of PNP transistors, therefore, the input bias current flows out of the device. If
either of the input signals falls below the negative common mode limit, the parasitic PN junction formed by the
substrate and the base of the PNP will turn on, resulting in an increase of input bias current.
7.2 Functional Block Diagram
7.3 Feature Description
If one of the inputs goes above the positive common mode limit, the output will still maintain the correct logic
level as long as the other input stays within the common mode range. However, the propagation delay will
increase. When both inputs are outside the common mode voltage range, current saturation occurs in the input
stage, and the output becomes unpredictable.
7.4 Device Functional Modes
The propagation delay does not increase significantly with large differential input voltages. However, large
differential voltages greater than the supply voltage should be avoided to prevent damages to the input stage.
The LMV7219 has a push-pull output. When the output switches, there is a direct path between VCC and ground,
causing high output sinking or sourcing current during the transition. After the transition, the output current
decreases and the supply current settles back to about 1.1 mA at 5 V, thus conserving power consumption.
Most high-speed comparators oscillate when the voltage of one of the inputs is close to or equal to the voltage
on the other input due to noise or undesirable feedback. The LMV7219 has 7 mV of internal hysteresis to counter
parasitic effects and noise. The hysteresis does not change significantly with the supply voltages and the
common mode input voltages as reflected in the specification table.
Copyright © 2000–2016, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: LMV7219
LMV7219
SNOS458I –APRIL 2000–REVISED JUNE 2016
www.ti.com
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The following section explains in detail how to manipulate the hysteresis voltage of the LMV7219. Detailed
expressions are provided along with practical considerations for designing hysteresis.
8.2 Typical Application
Figure 14 shows the typical method of adding external hysteresis to a comparator. The positive feedback is
responsible for shifting the comparator trip point depending on the state of the output.
Figure 14. Additional Hysteresis
8.2.1 Design Requirements
The internal hysteresis creates two trip points, one for the rising input voltage and one for the falling input
voltage, as shown in Figure 19. The difference between the trip points is the hysteresis. With internal hysteresis,
when the comparator's input voltages are equal, the hysteresis effectively causes one comparator-input voltage
to move quickly past the other, thus taking the input out of the region where oscillation occurs. Standard
comparators require hysteresis to be added with external resistors. The fixed internal hysteresis eliminates these
resistors.
8.2.2 Detailed Design Procedure
8.2.2.1 Additional Hysteresis
If additional hysteresis is desired, this can be done with the addition of three resistors using positive feedback, as
shown in Figure 14. The positive feedback method slows the comparator response time. Calculate the resistor
values as follows:
1. Select R3. The current through R3 should be greater than the input bias current to minimize errors. The
current through R3 (IF) at the trip point is (VREF - VOUT) /R3. Consider the two possible output states when solving
for R3, and use the smaller of the two resulting resistor values. The two formulas are:
R3 = VREF/IF
(1)
When VOUT = 0:
12
Submit Documentation Feedback
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: LMV7219
LMV7219
www.ti.com
SNOS458I –APRIL 2000–REVISED JUNE 2016
Typical Application (continued)
R3 = VCC - VREF /IF
(2)
When VOUT = VCC
2. Choose a hysteresis band required (VHB).
3. Calculate R1, where R1 = R3 X(VHB/VCC
:
)
4. Choose the trip point for VIN rising. This is the threshold voltage (VTHR) at which the comparator switches from
low to high as VIN rises about the trip point.
5. Calculate R2 as follows:
(3)
6. Verify the trip voltage and hysteresis as follows:
(4)
This method is recommended for additional hysteresis of up to a few hundred millivolts. Beyond that, the
impedance of R3 is low enough to affect the bias string and adjustment of R1 may be also required.
8.2.2.2 Zero-Crossing Detector
The inverting input is connected to ground and the non-inverting input is connected to 100mVp-p signal. As the
signal at the non-inverting input crosses 0 V, the comparator's output Changes State.
Figure 15. Zero-Crossing Detector
8.2.2.3 Threshold Detector
Instead of tying the inverting input to 0 V, the inverting input can be tied to a reference voltage. The non-inverting
input is connected to the input. As the input passes the VREF threshold, the comparator's output changes state.
Copyright © 2000–2016, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: LMV7219
LMV7219
SNOS458I –APRIL 2000–REVISED JUNE 2016
www.ti.com
Typical Application (continued)
Figure 16. Threshold Detector
8.2.2.4 Crystal Oscillator
A simple crystal oscillator using the LMV7219 is shown in Figure 17. Resistors R1 and R2 set the bias point at
the comparator's non-inverting input. Resistors R3, R4 and C1 sets the inverting input node at an appropriate DC
average level based on the output. The crystal's path provides resonant positive feedback and stable oscillation
occurs. The output duty cycle for this circuit is roughly 50%, but it is affected by resistor tolerances and to a
lesser extent by the comparator offset.
Figure 17. Crystal Oscillator
8.2.2.5 IR Receiver
The LMV7219 is an ideal candidate to be used as an infrared receiver. The infrared photo diode creates a
current relative to the amount of infrared light present. The current creates a voltage across RD. When this
voltage level cross the voltage applied by the voltage divider to the inverting input, the output transitions.
14
Submit Documentation Feedback
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: LMV7219
LMV7219
www.ti.com
SNOS458I –APRIL 2000–REVISED JUNE 2016
Typical Application (continued)
Figure 18. IR Receiver
8.2.3 Application Curve
Figure 19. Input and Output Waveforms, Non-Inverting Input Varied
Copyright © 2000–2016, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: LMV7219
LMV7219
SNOS458I –APRIL 2000–REVISED JUNE 2016
www.ti.com
9 Power Supply Recommendations
The LMV7219 can operate off a single supply or with dual supplies as long as the input CM voltage range (VCM
)
has the required headroom to the positive rail V+. The input range extends to slightly below V- voltage. Supplies
should be decoupled with low inductance, often ceramic, capacitors to ground less than 0.5 inches from the
device pins. The use of ground plane is recommended, and as in most high speed devices, it is advisable to
remove ground plane close to device sensitive pins such as the inputs.
10 Layout
10.1 Layout Guidelines
10.1.1 Circuit Layout and Bypassing
The LMV7219 requires high-speed layout. Follow these layout guidelines:
1. Power supply bypassing is critical, and will improve stability and eliminate possible output chatter. A
decoupling capacitor such as 0.1-µF ceramic should be placed as close as possible to V+ pin (and to V- pin if
used with dual supplies) as shown in Figure 20. An additional 2.2-µF tantalum capacitor may be required for
extra noise reduction.
2. Keep all leads short to reduce stray capacitance and lead inductance. It will also minimize unwanted parasitic
feedback around the comparator.
3. The device should be soldered directly to the PC board instead of using a socket.
4. Use a PC board with a good, unbroken low inductance ground plane as shown in Figure 20. Make sure
ground paths are low-impedance, especially were heavier currents are flowing.
5. Input traces should be kept away from output traces. This can be achieved by running a topside ground
plane between the output and inputs.
6. Run the ground trace under the device up to the bypass capacitor to shield the inputs from the outputs.
7. To prevent parasitic feedback when input signals are slow-moving, a small capacitor of 1000 pF or less can
be placed between the inputs. It can also help eliminate oscillations in the transition region. However, this
capacitor can cause some degradation to tpd when the source impedance is low.
16
Submit Documentation Feedback
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: LMV7219
LMV7219
www.ti.com
SNOS458I –APRIL 2000–REVISED JUNE 2016
10.2 Layout Example
Figure 20. SOT-23 Board Layout Example
Copyright © 2000–2016, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links: LMV7219
LMV7219
SNOS458I –APRIL 2000–REVISED JUNE 2016
www.ti.com
11 Device and Documentation Support
11.1 Documentation Support
11.1.1 Related Documentation
For related documentation, see the following:
•
•
Absolute Maximum Ratings for Soldering (SNOA549)
Semiconductor and IC Package Thermal Metrics (SPRA953)
11.2 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
11.3 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.4 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.5 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
18
Submit Documentation Feedback
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: LMV7219
PACKAGE OPTION ADDENDUM
www.ti.com
22-Oct-2022
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
LMV7219M5
ACTIVE
SOT-23
DBV
5
1000
Non-RoHS
& Green
Call TI
Level-1-260C-UNLIM
-40 to 85
C14A
Samples
LMV7219M5/NOPB
LMV7219M5X
ACTIVE
ACTIVE
SOT-23
SOT-23
DBV
DBV
5
5
1000 RoHS & Green
SN
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-40 to 85
-40 to 85
C14A
C14A
Samples
Samples
3000
Non-RoHS
& Green
Call TI
LMV7219M5X/NOPB
LMV7219M7
ACTIVE
ACTIVE
SOT-23
SC70
DBV
DCK
5
5
3000 RoHS & Green
SN
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-40 to 85
-40 to 85
C14A
C15
Samples
Samples
1000
Non-RoHS
& Green
Call TI
LMV7219M7/NOPB
LMV7219M7X/NOPB
ACTIVE
ACTIVE
SC70
SC70
DCK
DCK
5
5
1000 RoHS & Green
SN
SN
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-40 to 85
-40 to 85
C15
C15
Samples
Samples
3000 RoHS & Green
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
22-Oct-2022
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
29-Oct-2021
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LMV7219M5
LMV7219M5/NOPB
LMV7219M5X
SOT-23
SOT-23
SOT-23
SOT-23
SC70
DBV
DBV
DBV
DBV
DCK
DCK
DCK
5
5
5
5
5
5
5
1000
1000
3000
3000
1000
1000
3000
178.0
178.0
178.0
178.0
178.0
178.0
178.0
8.4
8.4
8.4
8.4
8.4
8.4
8.4
3.2
3.2
3.2
3.2
1.4
1.4
1.4
1.4
1.2
1.2
1.2
4.0
4.0
4.0
4.0
4.0
4.0
4.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
Q3
Q3
Q3
Q3
Q3
Q3
Q3
3.2
3.2
LMV7219M5X/NOPB
LMV7219M7
3.2
3.2
2.25
2.25
2.25
2.45
2.45
2.45
LMV7219M7/NOPB
LMV7219M7X/NOPB
SC70
SC70
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
29-Oct-2021
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
LMV7219M5
LMV7219M5/NOPB
LMV7219M5X
SOT-23
SOT-23
SOT-23
SOT-23
SC70
DBV
DBV
DBV
DBV
DCK
DCK
DCK
5
5
5
5
5
5
5
1000
1000
3000
3000
1000
1000
3000
208.0
208.0
208.0
208.0
208.0
208.0
208.0
191.0
191.0
191.0
191.0
191.0
191.0
191.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
LMV7219M5X/NOPB
LMV7219M7
LMV7219M7/NOPB
LMV7219M7X/NOPB
SC70
SC70
Pack Materials-Page 2
PACKAGE OUTLINE
DBV0005A
SOT-23 - 1.45 mm max height
S
C
A
L
E
4
.
0
0
0
SMALL OUTLINE TRANSISTOR
C
3.0
2.6
0.1 C
1.75
1.45
1.45
0.90
B
A
PIN 1
INDEX AREA
1
2
5
(0.1)
2X 0.95
1.9
3.05
2.75
1.9
(0.15)
4
3
0.5
5X
0.3
0.15
0.00
(1.1)
TYP
0.2
C A B
NOTE 5
0.25
GAGE PLANE
0.22
0.08
TYP
8
0
TYP
0.6
0.3
TYP
SEATING PLANE
4214839/G 03/2023
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. Refernce JEDEC MO-178.
4. Body dimensions do not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed 0.25 mm per side.
5. Support pin may differ or may not be present.
www.ti.com
EXAMPLE BOARD LAYOUT
DBV0005A
SOT-23 - 1.45 mm max height
SMALL OUTLINE TRANSISTOR
PKG
5X (1.1)
1
5
5X (0.6)
SYMM
(1.9)
2
3
2X (0.95)
4
(R0.05) TYP
(2.6)
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:15X
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
METAL
EXPOSED METAL
EXPOSED METAL
0.07 MIN
ARROUND
0.07 MAX
ARROUND
NON SOLDER MASK
DEFINED
SOLDER MASK
DEFINED
(PREFERRED)
SOLDER MASK DETAILS
4214839/G 03/2023
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
DBV0005A
SOT-23 - 1.45 mm max height
SMALL OUTLINE TRANSISTOR
PKG
5X (1.1)
1
5
5X (0.6)
SYMM
(1.9)
2
3
2X(0.95)
4
(R0.05) TYP
(2.6)
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
SCALE:15X
4214839/G 03/2023
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
www.ti.com
PACKAGE OUTLINE
DCK0005A
SOT - 1.1 max height
S
C
A
L
E
5
.
6
0
0
SMALL OUTLINE TRANSISTOR
C
2.4
1.8
0.1 C
1.4
1.1
B
1.1 MAX
A
PIN 1
INDEX AREA
1
2
5
NOTE 4
(0.15)
(0.1)
2X 0.65
1.3
2.15
1.85
1.3
4
3
0.33
5X
0.23
0.1
0.0
(0.9)
TYP
0.1
C A B
0.15
0.22
0.08
GAGE PLANE
TYP
0.46
0.26
8
0
TYP
TYP
SEATING PLANE
4214834/C 03/2023
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. Refernce JEDEC MO-203.
4. Support pin may differ or may not be present.
www.ti.com
EXAMPLE BOARD LAYOUT
DCK0005A
SOT - 1.1 max height
SMALL OUTLINE TRANSISTOR
PKG
5X (0.95)
1
5
5X (0.4)
SYMM
(1.3)
2
3
2X (0.65)
4
(R0.05) TYP
(2.2)
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:18X
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
METAL
EXPOSED METAL
EXPOSED METAL
0.07 MIN
ARROUND
0.07 MAX
ARROUND
NON SOLDER MASK
DEFINED
SOLDER MASK
DEFINED
(PREFERRED)
SOLDER MASK DETAILS
4214834/C 03/2023
NOTES: (continued)
4. Publication IPC-7351 may have alternate designs.
5. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
DCK0005A
SOT - 1.1 max height
SMALL OUTLINE TRANSISTOR
PKG
5X (0.95)
1
5
5X (0.4)
SYMM
(1.3)
2
3
2X(0.65)
4
(R0.05) TYP
(2.2)
SOLDER PASTE EXAMPLE
BASED ON 0.125 THICK STENCIL
SCALE:18X
4214834/C 03/2023
NOTES: (continued)
6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
7. Board assembly site may have different recommendations for stencil design.
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023, Texas Instruments Incorporated
相关型号:
LMV721M5/NOPB
Single, 5.5-V, 10-MHz, low noise (8.5-nV/√Hz) operational amplifier | DBV | 5 | -40 to 85
TI
©2020 ICPDF网 联系我们和版权申明